ISL28156, ISL28256 ® Data Sheet December 16, 2008 39µA Micropower Single and Dual Precision Rail-to-Rail Input-Output (RRIO) Low Input Bias Current Op Amps The ISL28156 and ISL28256 are micropower precision operational amplifiers optimized for single supply operation at 5V and can operated down to 2.4V. These devices feature an Input Range Enhancement Circuit (IREC), which enables them to maintain CMRR performance for input voltages greater than the positive supply. The input signal is capable of swinging 0.5V above a 5.0V supply (0.25V for a 2.5V supply) and to within 10mV from ground. The output operation is rail-to-rail. The 1/f corner of the voltage noise spectrum is at 1kHz. This results in low frequency noise performance, which can only be found on devices with an order of magnitude higher than the supply current. ISL28156 and ISL28256 can be operated from one lithium cell or two Ni-Cd batteries. The input range includes both positive and negative rail. The output swings to both rails. Ordering Information PART NUMBER (Note) PART MARKING Features • 39µA typical supply current • 5nA max input bias current • 250kHz gain bandwidth product (AV = 1) • 2.4V to 5.5V single supply voltage range • Rail-to-rail input and output • Enable pin (ISL28156 only) • Pb-free (RoHS compliant) Applications • Battery- or solar-powered systems • 4mA to 20mA current loops • Handheld consumer products • Medical devices • Sensor amplifiers • ADC buffers • DAC output amplifiers PACKAGE (Pb-free) PKG. DWG. # ISL28156FHZ-T7* GABV 6 Ld SOT-23 MDP0038 ISL28156FBZ 28156 FBZ 8 Ld SOIC MDP0027 ISL28156FBZ-T7* 28156 FBZ 8 Ld SOIC MDP0027 Coming Soon ISL28256FBZ 28256 FBZ 8 Ld SOIC MDP0027 Coming Soon ISL28256FBZ-T7* 28256 FBZ 8 Ld SOIC MDP0027 Coming Soon ISL28256FUZ 8256Z 8 Ld MSOP MDP0043 Coming Soon ISL28256FUZ-T7* 8256Z 8 Ld MSOP MDP0043 Pinouts OUT 1 V- 2 + - 6 V+ NC 1 5 ENABLE IN- 2 4 IN- IN+ 3 8 ENABLE 7 V+ + 6 OUT V- 4 OUT_A 1 IN-_A 2 IN+_A 3 V- 4 8 V+ - + + - 5 NC ISL28256 (8 LD MSOP) TOP VIEW ISL28256 (8 LD SOIC) TOP VIEW *Please refer to TB347 for details on reel specifications. NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. ISL28156 (8 LD SOIC) TOP VIEW ISL28156 (6 LD SOT-23) TOP VIEW IN+ 3 1 FN6154.5 OUT_A 1 7 OUT_B IN-_A 2 6 IN-_B IN+_A 3 5 IN+_B V- 4 8 V+ 7 OUT_B - + + - 6 IN-_B 5 IN+_B CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2006, 2007, 2008. All Rights Reserved. All other trademarks mentioned are the property of their respective owners. ISL28156, ISL28256 Absolute Maximum Ratings (TA = +25°C) Thermal Information Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5V Supply Turn On Voltage Slew Rate . . . . . . . . . . . . . . . . . . . . . 1V/µs Differential Input Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mA Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5V Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . V- - 0.5V to V+ + 0.5V ESD Rating Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3kV Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300V Thermal Resistance θJA (°C/W) 6 Ld SOT-23 Package . . . . . . . . . . . . . . . . . . . . . . . 230 6 Ld SO Package . . . . . . . . . . . . . . . . . . . . . . . . . . 110 8 Ld MSOP Package . . . . . . . . . . . . . . . . . . . . . . . . 115 Output Short-Circuit Duration . . . . . . . . . . . . . . . . . . . . . . .Indefinite Ambient Operating Temperature Range . . . . . . . . .-40°C to +125°C Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . +125°C Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA Electrical Specifications PARAMETER VOS V+ = 5V, V- = 0V,VCM = 2.5V, TA = +25°C unless otherwise specified. Boldface limits apply over the operating temperature range, -40°C to +125°C. Temperature data established by characterization. DESCRIPTION Input Offset Voltage CONDITIONS MIN (Note 1) TYP MAX (Note 1) UNIT 8 Ld SOIC -120 -200 -7 120 250 µV 6 Ld SOT-23 -400 -450 -7 400 450 µV ΔV OS --------------ΔT Input Offset Drive vs Temperature IOS Input Offset Current -1.5 -5 0.34 1.2 2.5 nA IB Input Bias Current -2 -3.5 1.14 5 5 nA 1.5 µV/°C EN Input Noise Voltage Density FO = 1kHz 46 nV/√Hz IN Input Noise Current Density FO = 1kHz 0.14 pA/√Hz CMIR Input Common-Mode Voltage Range CMRR Common-Mode Rejection Ratio VCM = 0V to 5V 80 75 110 dB PSRR Power Supply Rejection Ratio VS = 2.4V to 5V 90 75 104 dB AVOL Large Signal Voltage Gain VO = 0.5V to 4.5V, RL = 100kΩ 200 175 412 V/mV VO = 0.5V to 4.5V, RL = 1kΩ 35 30 70 V/mV VOUT Maximum Output Voltage Swing 0 Output low, RL = 100kΩ Output low, RL = 1kΩ SR Slew Rate GBW Gain Bandwidth Product IS,ON Supply Current, Enabled 2 5 V 3 6 8 mV 130 150 200 mV Output high, RL = 100kΩ 4.992 4.99 4.985 V Output high, RL = 1kΩ 4.85 4.8 4.88 V 0.05 V/µs AV = 1 250 29 18 39 kHz 47 56 µA FN6154.5 December 16, 2008 ISL28156, ISL28256 Electrical Specifications PARAMETER V+ = 5V, V- = 0V,VCM = 2.5V, TA = +25°C unless otherwise specified. Boldface limits apply over the operating temperature range, -40°C to +125°C. Temperature data established by characterization. (Continued) DESCRIPTION MIN (Note 1) CONDITIONS TYP MAX (Note 1) 10 14 16 UNIT IS,OFF Supply Current, Disabled IO+ Short-Circuit Output Current RL = 10Ω 28 23 31 mA IO- Short-Circuit Output Current RL = 10Ω 24 18 26 mA VSUPPLY Supply Operating Range Guaranteed by PSRR test 2.4 VENH Enable Pin High Level VENL Enable Pin Low Level 0.8 V IENH Enable Pin Input Current VEN = 5V 1 1.2 1.2 µA IENL Enable Pin Input Current VEN = 0V 16 25 30 nA tEN Enable to Output On-state Delay Time (ISL28156) VOUT = 1V (enable state); VEN = High to Low 10.8 µs tEN Enable to Output Off-state Delay Time (ISL28156) VOUT = 0V (disabled state) VEN = Low to High 0.1 µs 5 2 µA V V NOTE: 1. Parts are 100% tested at +25°C. Temperature limits established by characterization and are not production tested. Typical Performance Curves 3 RL = 1k 1 NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 2 0 -1 RL = 10k -2 RL = 100k -3 -4 -5 AV = 1 CL = 16.3pF VOUT = 10mVP-P -6 -7 -8 1k 10k 100k FREQUENCY (Hz) 1M 8 7 6 5 4 3 2 1 0 -1 -2 -3 -4 -5 -6 -7 -8 GAIN (dB) 50 40 Rf = 100k, Rg = 1k, RL = 10k 30 20 10 Rf = 9.09, Rg = 1k, RL = INF 0 Rf = 0, Rg = INF, RL = 10k -10 100 1k 10k 100k 1M FREQUENCY (Hz) FIGURE 3. CLOSED LOOP GAIN vs FREQUENCY 3 CL = 43.3pF CL = 38.3pF CL = 34.3pF AV = 1 RL = 10k VOUT = 10mVP-P 1k 10k 100k FREQUENCY (Hz) 1 RL = 10k CL = 16.3pF VOUT = 10mVP-P 1M VS = 2.4V 0 NORMALIZED GAIN (dB) 60 Rf = 1M, Rg = 1k, RL = 10k CL = 55.3pF CL = 49.3pF FIGURE 2. GAIN vs FREQUENCY vs CL FIGURE 1. GAIN vs FREQUENCY vs RL 70 CL = 63.3pF -1 VS = 5V -2 -3 -4 -5 -6 AV = 1 RL = 10k -8 VOUT = 10mVP-P -9 1k 10k -7 100k 1M FREQUENCY (Hz) FIGURE 4. GAIN vs FREQUENCY vs VS FN6154.5 December 16, 2008 ISL28156, ISL28256 Typical Performance Curves (Continued) 3 0 VOUT = 50mV 1 NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 1 VOUT = 10mV 2 0 -1 -2 VOUT = 100mV VOUT = 1V -3 -4 -5 AV = 1 RL = 1k CL = 16.3pF -6 -7 -8 1k -1 100k -4 -5 -6 -7 -9 1M VOUT = 10mV -3 -8 10k VOUT = 1V -2 VOUT = 50mV AV = 1 RL = 10k CL = 16.3pF VOUT = 100mV 1k 10k FREQUENCY (Hz) -1 0 VOUT = 1V -10 -2 -3 CMRR (dB) NORMALIZED GAIN (dB) 10 VOUT = 10mV 0 VOUT = 50mV -4 -5 -6 -8 -9 VOUT = 100mV AV = 1 RL = 100k CL = 16.3pF -7 1k AV = 1 RL = 10k CL = 16.3pF VCM = 1VP-P PP VS = 5V -30 -40 -50 -60 10k 100k -70 1M 100 1k 0 -10 PSRR- -40 -50 -20 -30 AV = 1 RL = 1k CL = 16.3pF VOUT = 1VP-P VS = 5V PSRR- -40 -50 PSRR+ -60 PSRR+ -60 -70 -70 -80 1M 10 AV = 1 RL = 1k CL = 16.3pF VOUT = 1VP-P VS = 2.4V PSRR (dB) PSRR (dB) -30 100k FIGURE 8. CMRR vs FREQUENCY 10 -20 10k FREQUENCY (Hz) FIGURE 7. GAIN vs FREQUENCY vs VOUT -10 VS = 2.4V -20 FREQUENCY (Hz) 0 1M FIGURE 6. GAIN vs FREQUENCY vs VOUT FIGURE 5. GAIN vs FREQUENCY vs VOUT 1 100k FREQUENCY (Hz) -80 100 1k 10k 100k FREQUENCY (Hz) FIGURE 9. PSRR vs FREQUENCY, VS = 2.4V 4 1M -90 100 1k 10k 100k 1M FREQUENCY (Hz) FIGURE 10. PSRR vs FREQUENCY, VS = 5V FN6154.5 December 16, 2008 ISL28156, ISL28256 Typical Performance Curves (Continued) 1.4 INPUT CURRENT NOISE (pA/√Hz) 140 120 100 80 60 40 20 0 1 10 100 1k 1.2 1.0 0.8 0.6 0.4 0.2 0 10k 1 10 100 FREQUENCY (Hz) FIGURE 11. INPUT VOLTAGE NOISE vs FREQUENCY 0 24 -0.6 -0.8 -1.0 20 18 16 14 12 -1.2 -1.4 RF = Ri = RL = 10k AV = 2 CL = 16.3pF VOUT = 10mVP-P 22 SMALL SIGNAL (mV) INPUT NOISE (µV) -0.4 0 1 2 3 4 5 6 7 8 9 10 10 0 50 100 150 0.6 6 0.4 5 ENABLE (V) 0 -0.6 RF = Ri = RL = 10k AV = 2 CL = 16.3pF VOUT = 1VP-P 0 100 200 350 400 1.0 V-ENABLE 0.8 3 0.6 RF = Ri =RL = 10k AV = 2 CL = 16.3pF VOUT = 10mVP-P 2 1 0.4 0.2 0 300 TIME (µs) FIGURE 15. LARGE SIGNAL STEP RESPONSE 5 300 1.2 4 0.2 -0.4 250 FIGURE 14. SMALL SIGNAL STEP RESPONSE FIGURE 13. 1Hz TO 10Hz INPUT NOISE -0.2 200 TIME (µs) TIME (s) LARGE SIGNAL (V) 10k FIGURE 12. INPUT CURRENT NOISE vs FREQUENCY AV = 1000 RF = 100k Ri = 100 RL = 10k -0.2 1k FREQUENCY (Hz) 400 -1 OUTPUT (V) INPUT VOLTAGE NOISE (nV/√Hz) 160 0 VOUT 0 10 20 30 40 50 60 70 80 90 -0.2 100 TIME (µs) FIGURE 16. ENABLE TO OUTPUT DELAY FN6154.5 December 16, 2008 ISL28156, ISL28256 Typical Performance Curves (Continued) 58 14.5 n = 1000 MAX MAX 12.5 48 CURRENT (µA) CURRENT (µA) n = 1000 13.5 53 MEDIAN 43 38 33 11.5 MEDIAN 10.5 9.5 8.5 MIN 28 7.5 23 -40 6.5 -40 -20 0 20 40 60 80 100 120 MIN -20 0 TEMPERATURE (°C) FIGURE 17. SUPPLY CURRENT ENABLED vs TEMPERATURE VS = ±2.5V 280 n = 1000 MAX 80 100 120 100 120 200 MEDIAN VIO (µV) VIO (µV) 80 -20 -120 -220 MEDIAN 100 0 -100 -200 MIN -320 -420 -40 MAX 300 180 -20 0 20 40 60 80 TEMPERATURE (°C) MIN -300 100 -400 -40 120 -20 0 20 40 60 80 TEMPERATURE (°C) FIGURE 19. VIO SO8 PACKAGE vs TEMPERATURE VS = ±2.5V FIGURE 20. VIO SO8 PACKAGE vs TEMPERATURE VS = ±1.2V 380 400 280 300 n = 1000 MAX MAX n = 1000 180 200 MEDIAN VIO (µV) VIO (µV) 60 400 n = 1000 -20 -120 100 MEDIAN 0 -100 -220 -200 MIN -320 -420 -40 40 FIGURE 18. SUPPLY CURRENT DISABLED vs TEMPERATURE VS = ±2.5V 380 80 20 TEMPERATURE (°C) MIN -300 -20 0 20 40 60 80 TEMPERATURE (°C) 100 120 FIGURE 21. VIO SOT-23 PACKAGE vs TEMPERATURE VS = ±2.5V 6 -400 -40 -20 0 20 40 60 80 TEMPERATURE (°C) 100 120 FIGURE 22. VIO SOT-23 PACKAGE vs TEMPERATURE VS = ±1.2V FN6154.5 December 16, 2008 ISL28156, ISL28256 Typical Performance Curves (Continued) 5 5 n = 1000 4 3 MAX 2 IBIAS- (nA) IBIAS+ (nA) n = 1000 MAX 4 1 MEDIAN 0 3 2 1 MEDIAN MIN -1 0 MIN -2 -3 -40 -20 0 20 40 60 80 100 -1 -40 120 -20 0 TEMPERATURE (°C) FIGURE 23. IBIAS+ vs TEMPERATURE VS = ±2.5V 80 100 120 n = 1000 n = 1000 8 MAX MAX 6 0 -1 IBIAS- (nA) IBIAS+ (nA) 60 10 MEDIAN -2 MEDIAN 4 2 0 -3 -2 MIN -4 -40 -20 0 20 40 60 MIN 80 100 -4 -40 120 -20 0 TEMPERATURE (°C) 20 40 60 80 TEMPERATURE (°C) 100 120 FIGURE 25. IBIAS+ vs TEMPERATURE VS = ±1.5V FIGURE 26. IBIAS- vs TEMPERATURE VS = ±1.2V 4 4 3 n = 1000 MAX 0 1 IOS (nA) 0 -1 -2 MEDIAN -3 -2 MEDIAN -4 -6 MIN -4 MIN -8 -5 -6 -40 n = 1000 MAX 2 2 IOS (nA) 40 FIGURE 24. IBIAS- vs TEMPERATURE VS = ±2.5V 2 1 20 TEMPERATURE (°C) -20 0 20 40 60 80 100 TEMPERATURE (°C) FIGURE 27. IOS vs TEMPERATURE VS = ±2.5V 7 120 -10 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (°C) FIGURE 28. IOS vs TEMPERATURE VS = ±1.5V FN6154.5 December 16, 2008 ISL28156, ISL28256 Typical Performance Curves (Continued) 130 135 130 115 MEDIAN 110 105 100 110 MEDIAN 105 100 95 90 90 -40 85 -40 -20 0 20 40 60 80 TEMPERATURE (°C) 4.900 100 120 MIN -20 0 20 40 60 80 TEMPERATURE (°C) MAX n = 1000 MAX 4.9980 4.885 VOUT (V) MEDIAN 4.880 4.875 4.870 4.9978 MEDIAN 4.9976 4.9974 MIN 4.865 120 4.9984 4.9982 4.890 100 FIGURE 30. PSRR vs TEMPERATURE ±1.2V to ±2.5V n = 1000 4.895 VOUT (V) 115 95 MIN FIGURE 29. CMRR vs TEMPERATURE V+ = ±2.5V, ±1.5V MIN 4.9972 4.860 4.9970 4.855 4.850 -40 -20 0 20 40 60 80 TEMPERATURE (°C) 100 120 4.9968 -40 FIGURE 31. VOUT HIGH vs TEMPERATURE VS = ±2.5V, RL = 1k MAX 4.9982 -20 0 20 40 60 80 TEMPERATURE (°C) n = 1000 MAX 4.5 VOUT (mV) MEDIAN 4.9976 4.9974 4.0 3.5 MEDIAN MIN 4.9972 120 5.0 n = 1000 4.9980 4.9978 100 FIGURE 32. VOUT HIGH VS = ±2.5V, RL = 100k 4.9984 VOUT (V) MAX 120 120 PSRR (dB) CMRR (dB) 125 n = 1000 125 MAX n = 1000 3.0 MIN 4.9970 4.9968 -40 -20 0 20 40 60 80 TEMPERATURE (°C) 100 FIGURE 33. VOUT LOW VS = ±2.5V, RL = 1k 8 120 2.5 -40 -20 0 20 40 60 80 TEMPERATURE (°C) 100 120 FIGURE 34. VOUT LOW VS = ±2.5V, RL = 100k FN6154.5 December 16, 2008 ISL28156, ISL28256 Pin Descriptions ISL28156 (6 Ld SOT-23) ISL28156 (8 Ld SOIC) ISL28256 (8 Ld MSOP) PIN NAME 1, 5 4 2 2 (A) 6 (B) FUNCTION NC Not connected ININ-_A IN-_B Inverting input EQUIVALENT CIRCUIT V+ IN- IN+ VCircuit 1 3 3 (A) 5 (B) IN+ IN+_A IN+_B 4 V- 1 (A) 7 (B) OUT OUT_A OUT_B 3 2 4 1 6 Non-inverting input (See Circuit 1) Negative supply Output V+ OUT VCircuit 2 6 7 5 8 8 V+ ENABLE Positive supply Chip enable V+ CE VCircuit 3 Applications Information Introduction The ISL28156 is a single BiMOS rail-to-rail input, output (RRIO) operational amplifier with an enable feature. The ISL28256 is a dual version without the enable feature. Both devices are designed to operate from single supply (2.4V to 5.0V) or dual supplies (±1.2V to ±2.5V) while drawing only 39µA of supply current per amplifier. This combination of low power and precision performance makes this device suitable for a variety of low power applications including battery powered systems. Input Protection All input terminals have internal ESD protection diodes to both positive and negative supply rails, limiting the input voltage to within one diode beyond the supply rails. They also contain back-to-back diodes across the input terminals. For applications where the input differential voltage is expected to exceed 0.5V, external series resistors must be used to ensure the input currents never exceed 5mA (Figure 35). VIN VOUT RIN + RL Rail-to-Rail Input/Output These devices feature bi-polar inputs, which have an input common mode range that extends up to 0.5V beyond the V+ rail, and to within 10mV of the V- rail. The CMOS outputs typically swing to within about 4mV of the supply rails with a 100kΩ load. The NMOS sinks current to swing the output in the negative direction. The PMOS sources current to swing the output in the positive direction. 9 FIGURE 35. INPUT CURRENT LIMITING Enable/Disable Feature The ISL28156 offers an EN pin that disables the device when pulled up to at least 2.0V. In the disabled state (output in a high impedance state), the part consumes typically 10µA. By disabling the part, multiple ISL28156 parts can be connected together as a MUX. In this configuration, the outputs are tied together in parallel and a channel can be selected by the EN FN6154.5 December 16, 2008 ISL28156, ISL28256 pin. The EN pin also has an internal pull-down. If left open, the EN pin will pull to the negative rail and the device will be enabled by default. The loading effects of the feedback resistors of the disabled amplifier must be considered when multiple amplifier outputs are connected together. Using Only One Channel The ISL28256 is a dual op amp. If the application only requires one channel, the user must configure the unused channel to prevent it from oscillating. The unused channel will oscillate if the input and output pins are floating. This will result in higher than expected supply currents and possible noise injection into the channel being used. The proper way to prevent this oscillation is to short the output to the negative input and ground the positive input (as shown in Figure 36). Power Dissipation It is possible to exceed the +125°C maximum junction temperatures under certain load and power-supply conditions. It is therefore important to calculate the maximum junction temperature (TJMAX) for all applications to determine if power supply voltages, load conditions, or package type need to be modified to remain in the safe operating area. These parameters are related using Equation 1: T JMAX = T MAX + ( θ JA xPD MAXTOTAL ) (EQ. 1) where: • PDMAXTOTAL is the sum of the maximum power dissipation of each amplifier in the package (PDMAX) PDMAX for each amplifier can be calculated using Equation 2: V OUTMAX PD MAX = 2*V S × I SMAX + ( V S - V OUTMAX ) × ---------------------------R L - (EQ. 2) + where: FIGURE 36. PREVENTING OSCILLATIONS IN UNUSED CHANNELS Current Limiting • TMAX = Maximum ambient temperature • θJA = Thermal resistance of the package • PDMAX = Maximum power dissipation of 1 amplifier These devices have no internal current-limiting circuitry. If the output is shorted, it is possible to exceed the Absolute Maximum Rating for output current or power dissipation, potentially resulting in the destruction of the device. • VS = Supply voltage • IMAX = Maximum supply current of 1 amplifier • VOUTMAX = Maximum output voltage swing of the application • RL = Load resistance 10 FN6154.5 December 16, 2008 ISL28156, ISL28256 SOT-23 Package Family MDP0038 e1 D SOT-23 PACKAGE FAMILY A MILLIMETERS 6 N SYMBOL 4 E1 2 E 3 0.15 C D 1 2X 2 3 0.20 C 5 2X e 0.20 M C A-B D B b NX 0.15 C A-B 1 3 SOT23-5 SOT23-6 A 1.45 1.45 MAX A1 0.10 0.10 ±0.05 A2 1.14 1.14 ±0.15 b 0.40 0.40 ±0.05 c 0.14 0.14 ±0.06 D 2.90 2.90 Basic E 2.80 2.80 Basic E1 1.60 1.60 Basic e 0.95 0.95 Basic e1 1.90 1.90 Basic L 0.45 0.45 ±0.10 L1 0.60 0.60 Reference N 5 6 Reference D 2X TOLERANCE Rev. F 2/07 NOTES: C A2 2. Plastic interlead protrusions of 0.25mm maximum per side are not included. SEATING PLANE A1 0.10 C 1. Plastic or metal protrusions of 0.25mm maximum per side are not included. 3. This dimension is measured at Datum Plane “H”. 4. Dimensioning and tolerancing per ASME Y14.5M-1994. NX 5. Index area - Pin #1 I.D. will be located within the indicated zone (SOT23-6 only). (L1) 6. SOT23-5 version has no center lead (shown as a dashed line). H A GAUGE PLANE c L 11 0.25 0° +3° -0° FN6154.5 December 16, 2008 ISL28156, ISL28256 Small Outline Package Family (SO) A D h X 45° (N/2)+1 N A PIN #1 I.D. MARK E1 E c SEE DETAIL “X” 1 (N/2) B L1 0.010 M C A B e H C A2 GAUGE PLANE SEATING PLANE A1 0.004 C 0.010 M C A B L b 0.010 4° ±4° DETAIL X MDP0027 SMALL OUTLINE PACKAGE FAMILY (SO) INCHES SYMBOL SO-14 SO16 (0.300”) (SOL-16) SO20 (SOL-20) SO24 (SOL-24) SO28 (SOL-28) TOLERANCE NOTES A 0.068 0.068 0.068 0.104 0.104 0.104 0.104 MAX - A1 0.006 0.006 0.006 0.007 0.007 0.007 0.007 ±0.003 - A2 0.057 0.057 0.057 0.092 0.092 0.092 0.092 ±0.002 - b 0.017 0.017 0.017 0.017 0.017 0.017 0.017 ±0.003 - c 0.009 0.009 0.009 0.011 0.011 0.011 0.011 ±0.001 - D 0.193 0.341 0.390 0.406 0.504 0.606 0.704 ±0.004 1, 3 E 0.236 0.236 0.236 0.406 0.406 0.406 0.406 ±0.008 - E1 0.154 0.154 0.154 0.295 0.295 0.295 0.295 ±0.004 2, 3 e 0.050 0.050 0.050 0.050 0.050 0.050 0.050 Basic - L 0.025 0.025 0.025 0.030 0.030 0.030 0.030 ±0.009 - L1 0.041 0.041 0.041 0.056 0.056 0.056 0.056 Basic - h 0.013 0.013 0.013 0.020 0.020 0.020 0.020 Reference - 16 20 24 28 Reference - N SO-8 SO16 (0.150”) 8 14 16 Rev. M 2/07 NOTES: 1. Plastic or metal protrusions of 0.006” maximum per side are not included. 2. Plastic interlead protrusions of 0.010” maximum per side are not included. 3. Dimensions “D” and “E1” are measured at Datum Plane “H”. 4. Dimensioning and tolerancing per ASME Y14.5M-1994 12 FN6154.5 December 16, 2008 ISL28156, ISL28256 Mini SO Package Family (MSOP) 0.25 M C A B D MINI SO PACKAGE FAMILY (N/2)+1 N E MDP0043 A E1 MILLIMETERS PIN #1 I.D. 1 B (N/2) e H C SEATING PLANE 0.10 C N LEADS SYMBOL MSOP8 MSOP10 TOLERANCE NOTES A 1.10 1.10 Max. - A1 0.10 0.10 ±0.05 - A2 0.86 0.86 ±0.09 - b 0.33 0.23 +0.07/-0.08 - c 0.18 0.18 ±0.05 - D 3.00 3.00 ±0.10 1, 3 E 4.90 4.90 ±0.15 - E1 3.00 3.00 ±0.10 2, 3 e 0.65 0.50 Basic - L 0.55 0.55 ±0.15 - L1 0.95 0.95 Basic - N 8 10 Reference - 0.08 M C A B b Rev. D 2/07 NOTES: 1. Plastic or metal protrusions of 0.15mm maximum per side are not included. L1 2. Plastic interlead protrusions of 0.25mm maximum per side are not included. A 3. Dimensions “D” and “E1” are measured at Datum Plane “H”. 4. Dimensioning and tolerancing per ASME Y14.5M-1994. c SEE DETAIL "X" A2 GAUGE PLANE A1 L 0.25 3° ±3° DETAIL X All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 13 FN6154.5 December 16, 2008