Cymbet CBC3150-D9C-WP Capacitance to enerchip battery charge conversion guide Datasheet

Preliminary
AN-1057
Application Note
Capacitance to EnerChip Battery Charge Conversion Guide
Introduction
EnerChips are solid state rechargeable batteries that have a high charge-discharge cycle life, very low selfdischarge, and are constructed with solid state materials, making them durable, non-toxic, and safe to use in
a range of environments. EnerChip CC products include an EnerChip battery management circuit co-packaged
in low profile solder reflowable, surface mount QFN and DFN-style packages. EnerChips are often used as a
real-time clock (RTC) and memory backup power source. Supercapacitors are also used in these applications,
although there are significant differences in the operating characteristics of these two categories of energy
storage devices. An important distinction to understand when comparing effective charge storage capacity is
that the EnerChip delivers charge at a relatively fixed voltage, while supercapacitors deliver charge at an everdeclining voltage, the voltage-charge slope being a function of discharge current.
A frequently asked question is: “If I’m using a supercapacitor as a backup power source for an RTC and want
to replace it with a solid state battery, what battery capacity is equivalent to the supercapacitor rating?”
In answering the question, one must recognize the differences in discharge profiles between EnerChips and
supercapacitors. In relative terms, the percentage of supercapacitor storage capacity available to the load is
linearly dependent on the minimum voltage at which the load device (e.g., RTC) will continue to operate. In
contrast, the EnerChip CC output voltage is nearly constant over the entire discharge, as depicted in Figure
1. EnerChip CC products have a self-contained battery management circuit that controls battery charging and
delivers >95% of the stored energy at a relatively steady output voltage of 3.3V before going into cutoff.
Figure 1: Relative Charge Capacity Delivered to a Load - Green Line Represents the EnerChip CC; Blue Line
Represents a Supercapacitor.
Figure 1 Notes:
1) Capacitor charge voltage = 3.3V. 2) Constant current discharge. 3) Assumes negligible self-discharge of capacitor and EnerChip
4) EnerChip CC voltage derived from 3.8V terminal voltage, less 0.5V diode drop to Vout.
©2013 Cymbet Corporation • Tel: +1-763-633-1780 • www.cymbet.com
Doc AN-72-1057 Rev B
Page 1 of 3
Preliminary
AN-1057: Capacitance to EnerChip Battery Charge Conversion Guide
Figure 1 profiles do not account for the effects of self-discharge, which are measurably worse for
supercapacitors than for the EnerChip solid state battery.
Another frequently asked question is: “How much storage capacity do I need for my application?”
The simplest calculation involves multiplying the RTC/MCU/SRAM operating current (at the backup power
source voltage) times the number of hours needed for backup. The product is the amount of charge capacity
needed, in ampere-hours. When calculating the device run time in backup mode, it is sometimes necessary
to include de-rating factors such as storage device characteristics vs. temperature and aging, as well as load
current consumption over temperature and voltage. This is particularly true if precise knowledge of minimum
available backup time over life of product is required.
Comparing - in absolute terms - EnerChip storage capacity to supercapacitors in a comparable energy storage
range, we turn to Figure 2. Recalling the state-of-charge dependence typical of supercapacitors, three lines are
drawn, representing the minimum operating voltage (Vmin) at which the load can operate. Note that as Vmin
rises, a diminishing amount of useful charge is available from the supercapacitor. (Again, the relatively high
self-discharge of supercapacitors has been ignored here for the sake of clarity.) For reference, EnerChips range
from a few microampere-hours to several tens of microampere-hours, corresponding to equivalent capacitance
of tens to hundreds of millifarads.
Figure 2: Charge Capacity of EnerChips vs. Supercapacitors at Several Discharge Cutoff Voltage Levels.
In addition to the battery (EnerChip) management functions, the EnerChip CC has additional functions that
are useful and often necessary in backup power applications - such as supply voltage threshold detection and
a power-good indicator. EnerChip CC devices also have temperature-dependent battery charge compensation
included to improve the service life of the product. For more technical information related to the EnerChip and
EnerChip CC products, refer to the Cymbet Corporation web site: www.cymbet.com.
©2013 Cymbet Corporation • Tel: +1-763-633-1780 • www.cymbet.com
Doc AN-72-1057 Rev B
Page 2 of 3
Preliminary
AN-1057: Capacitance to EnerChip Battery Charge Conversion Guide
Cymbet Product Ordering Information
EnerChip CC Part Number
Description
Notes
CBC3105-R4C
EnerChip CC 5µAh in 16-pin DFN
Shipped in Tube
CBC3105-R4C-TR1
CBC3105-R4C-TR5
EnerChip CC 5µAh in 16-pin DFN
Tape-and-Reel - 1000 pcs (TR1) or
5000 pcs (TR5) per reel
CBC3105-R4C-WP
EnerChip CC 5µAh in 16-pin DFN
Waffle Pack
CBC3112-D7C
EnerChip CC 12µAh in 20-pin D7
DFN Package
Shipped in Tube
CBC3112-D7C-TR1
CBC3112-D7C-TR5
EnerChip CC 12µAh in 20-pin D7
DFN Package
Tape-and-Reel - 1000 pcs (TR1) or
5000 pcs (TR5) per reel
CBC3112-D7C-WP
EnerChip CC 12µAh in 20-pin D7
DFN Package
Waffle Pack
CBC3150-D9C
EnerChip CC 50µAh in 20-pin D9
DFN Package
Shipped in Tube
CBC3150-D9C-TR1
CBC3150-D9C-TR5
EnerChip CC 50µAh in 20-pin D9
DFN Package
Tape-and-Reel - 1000 pcs (TR1) or
5000 pcs (TR5) per reel
CBC3150-D9C-WP
EnerChip CC 50µAh in 20-pin D9
DFN Package
Waffle Pack
U.S. Patent No. 8,044,508. Additional U.S. and Foreign Patents Pending
Disclaimer of Warranties; As Is
The information provided in this data sheet is provided “As Is” and Cymbet Corporation disclaims all representations or warranties of any
kind, express or implied, relating to this data sheet and the Cymbet EnerChip product described herein, including without limitation, the
implied warranties of merchantability, fitness for a particular purpose, non-infringement, title, or any warranties arising out of course of
dealing, course of performance, or usage of trade. Cymbet EnerChip products are not authorized for use in life critical applications. Users
shall confirm suitability of the Cymbet EnerChip product in any products or applications in which the Cymbet EnerChip product is adopted
for use and are solely responsible for all legal, regulatory, and safety-related requirements concerning their products and applications and
any use of the Cymbet EnerChip product described herein in any such product or applications.
Cymbet, the Cymbet Logo, and EnerChip are Cymbet Corporation Trademarks
©2013 Cymbet Corporation • Tel: +1-763-633-1780 • www.cymbet.com
Doc AN-72-1057 Rev B
Page 3 of 3
Similar pages