HPL11PT CHENMKO ENTERPRISE CO.,LTD THRU SURFACE MOUNT GLASS PASSIVATED HIGH EFFICIENCY SILICON RECTIFIER VOLTAGE RANGE 50 - 1000 Volts CURRENT 1.0 Ampere HPL18PT PROVISIONAL SPEC. FEATURE *Sm al l S u r f ac e M o u n t i n g T y p e. (SMP) * Low forward voltage, high current capability * Low leakage current * Glass passivated junction * High temperature soldering guaranteed : 260oC/10 seconds at terminals SMP 0.081 (2.05) 0.077 (1.95) 0.170 (4.31) 0.163 (4.15) (3) (1) (2) 0.019 (0.50 Min.) 0.077 (1.95) 0.073 (1.85) 0.045 (1.16) 0.042 (1.07) 0.005 (0.15 Min.) 0.019 (0.50 Min.) 0.264 (6.70) 0.254 (6.46) CIRCUIT 2 0.212 (5.38) 0.208 (5.29) 1 0.055 (1.40) 0.051 (1.30) SMP Dimensions in inches and (millimeters) 3 MAXIMUM RATINGES ( At TA = 25oC unless otherwise noted ) RATINGS SYMBOL HPL11PT HPL12PT HPL13PT HPL14PT HPL15PT HPL16PT HPL17PT HPL18PT UNITS Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 300 400 600 800 1000 Volts Maximum RMS Voltage VRMS 35 70 140 210 280 420 560 700 Volts Maximum DC Blocking Voltage VDC 50 100 200 300 400 600 800 1000 Volts o Maximum Average Forward Rectified Current TL = 110 C IO 1.0 Amps IFSM 30 Amps Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note 1) Operating and Storage Temperature Range CJ 15 TJ, TSTG 12 pF o -65 to +150 C ELECTRICAL CHARACTERISTICS ( At TA = 25oC unless otherwise noted ) CHARACTERISTICS SYMBOL Maximum Instantaneous Forward Voltage at 1.0 A DC Maximum DC Reverse Current at Rated DC Blocking Voltage at TA = 25oC Maximum Full Load Reverse Current Average, Full Cycle at TA = 55oC Maximum Reverse Recovery Time (Note 2) NOTES : 1. Measured at 1.0 MHZ and applied reverse voltage of 4.0 volts 2. Test Conditions : IF = 0.5 A, IR = -1.0 A, IRR = -0.25 A VF HPL11PT HPL12PT HPL13PT HPL14PT HPL15PT HPL16PT HPL17PT HPL18PT 1.0 1.3 1.5 1.7 UNITS Volts 5.0 uAmps 100 uAmps IR trr 50 70 nSec 2004-7 RATING CHARACTERISTIC CURVES ( HPL11PT THRU HPL18PT ) 10 NONINDUCTIVE trr +0.5A (-) D.U.T (+) 0 PULSE GENERATOR (NOTE 2) 25 Vdc (approx) (-) 1 NONINDUCTIVE OSCILLOSCOPE (NOTE 1) -0.25A (+) -1.0A 1cm NOTES: 1. Rise Time = 7 ns max. Input Impedance = 1 megohm. 22 pF. 2. Rise Time = 10 ns max. Source Impedlance= 50 ohms. SET TIME BASE FOR 10/20 nS/cm FIG. 3 - TYPICAL REVERSE CHARACTERISTICS 1.0 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.5 0 0 25 50 75 100 125 150 175 LEAD TEMPERATURE ( OC ) TJ =100oC 1.0 TJ =25oC .1 8P T 6P L1 HP L1 HP HP L1 L14 7P PT T~ ~H PT L11 HP ~H PL1 PL1 5PT 3PT Pulse Width = 300uS 1% Duty Cycle 1.0 HP TJ =125oC 10 T 10 INSTANTANEOUS FORWARD CURRENT, ( A ) INSTANTANEOUS REVERSE CURRENT, (uA) 1.5 FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 100 0.1 TJ =25oC .01 .001 .01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, ( % ) 0 .2 .4 .6 .8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, ( V ) FIG. 5 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 1.8 FIG. 6 - TYPICAL JUNCTION CAPACITANCE 35 200 30 JUNCTION CAPACITANCE, ( pF ) PEAK FORWARD SURGE CURRENT, ( A ) FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT, ( A ) FIG. 1 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50 NONINDUCTIVE 8.3ms Single Half Sine-Wave (JEDEC Method) 25 20 15 10 5 0 100 60 40 HPL1 1~HP L15 20 HPL16 10 ~HPL1 8 6 4 TJ =25oC 2 1 1 2 5 10 20 NUMBER OF CYCLES AT 60 Hz 50 100 .1 .2 .4 1.0 2 4 10 20 REVERSE VOLTAGE, ( V ) 40 100