ASM3P2969A Low Power Peak EMI Reducing Solution Description The ASM3P2969A is a versatile spread spectrum frequency modulator designed specifically for a wide range of clock frequencies. The ASM3P2969A reduces electromagnetic interference (EMI) at the clock source, allowing system wide reduction of EMI of all clock dependent signals. The ASM3P2969A allows significant system cost savings by reducing the number of circuit board layers, ferrite beads and shielding that are traditionally required to pass EMI regulations. The ASM3P2969A uses the most efficient and optimized modulation profile approved by the FCC and is implemented by using a proprietary all digital method. The ASM3P2969A modulates the output of a single PLL in order to “spread” the bandwidth of a synthesized clock, and more importantly, decreases the peak amplitudes of its harmonics. This results in significantly lower system EMI compared to the typical narrow band signal produced by oscillators and most frequency generators. Lowering EMI by increasing a signal’s bandwidth is called ‘spread spectrum clock generation.’ Applications The ASM3P2969A is targeted towards all portable devices with very low power requirements like MP3 players, Notebooks and digital still cameras. http://onsemi.com TSOT−6 O SUFFIX CASE 419AF • • • • SOIC−8 S SUFFIX CASE 751BD PIN CONFIGURATIONS 1 REFOUT/2 VSS ModOUT XOUT VDD XIN / CLKIN 6−Pin TSOT−23 Package (Top View) Features • • • • • • TSSOP−8 T SUFFIX CASE 948AL 1 Generates an EMI Optimized Clock Signal at the Output Integrated Loop Filter Components Operates with a 3.3 V / 2.5 V Supply Operating Current less than 4 mA Low Power CMOS Design Input Frequency Range: 6 MHz to 12 MHz for 2.5 V 6 MHz to 13 MHz for 3.3 V Generates a 1X Low EMI Spread Spectrum Clock of the Input Frequency Frequency Deviation: ±1% @ 10 MHz Available in 6−pin TSOT−23, 8−pin SOIC and 8−pin TSSOP Packages These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS Compliant VDD XIN / CLKIN NC XOUT ModOUT REFOUT/2 VSS NC 8−Pin SOIC and TSSOP Packages (Top View) KEY SPECIFICATIONS Specification Description Supply Voltages VDD = 3.3 V / 2.5 V Cycle−to−Cycle Jitter 200 pS (Max) Output Duty Cycle 45/55% Modulation Rate Equation FIN/256 Frequency Deviation ±1% @ 10 MHz ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 10 of this data sheet. © Semiconductor Components Industries, LLC, 2011 August, 2011 − Rev. 3 1 Publication Order Number: ASM3P2969A/D ASM3P2969A VDD PLL Modulation XIN XOUT Frequency Divider Crystal Oscillator Phase Detector Feedback Divider Loop Filter VCO Output Divider ModOUT DIV/2 REFOUT/2 VSS Figure 1. Block Diagram Table 1. PIN DESCRIPTION (6−Pin TSOT−23 Package) Pin# Pin Name Type Description 1 REFOUT/2 O Buffered and divided by 2 output of the input frequency. 2 XOUT O Crystal connection. If using an external reference, this pin must be left unconnected. 3 XIN / CLKIN I Crystal connection or external reference frequency input. This pin has dual functions. It can be connected either to an external crystal or an external reference clock. 4 VDD P Power supply for the entire chip. 5 ModOUT O Spread spectrum clock output. 6 VSS P Ground connection. Table 2. PIN DESCRIPTION (8−Pin SOIC and TSSOP Packages) Pin# Pin Name Type 1 XIN / CLKIN I Crystal connection or external reference frequency input. This pin has dual functions. It can be connected either to an external crystal or an external reference clock. Description 2 XOUT O Crystal connection. If using an external reference, this pin must be left unconnected. 3 REFOUT/2 O Buffered and divided by 2 output of the input frequency. 4 NC − No connect. 5 VSS P Ground connection. 6 ModOUT O Spread spectrum clock output. 7 NC − No connect. 8 VDD P Power supply for the entire chip. http://onsemi.com 2 ASM3P2969A Figure 2. Modulation Profile Table 3. SPECIFICATIONS Description Frequency Range Specification For 2.5 V Supply 6 MHz < CLKIN < 12 MHz For 3.3 V Supply 6 MHz < CLKIN < 13 MHz Modulation Equation FIN/256 Frequency Deviation ±1% @ 10 MHz Table 4. ABSOLUTE MAXIMUM RATINGS Symbol VDD, VIN TSTG Parameter Rating Unit Voltage on any pin with respect to Ground −0.5 to +4.6 V Storage temperature −65 to +125 °C TA Operating temperature −40 to +85 °C Ts Max. Soldering Temperature (10 sec) 260 °C TJ Junction Temperature 150 °C 2 KV TDV Static Discharge Voltage (As per JEDEC STD22− A114−B) Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. http://onsemi.com 3 ASM3P2969A Table 5. DC ELECTRICAL CHARACTERISTICS FOR 2.5 V SUPPLY (Test condition: All parameters are measured at room temperature (+25°C) unless otherwise stated.) Parameter Symbol Min Typ Max Unit VIL Input low voltage VSS−0.3 − 0.8 V VIH Input high voltage 2.0 − VDD+0.3 V IIL Input low current − − −35 mA IIH Input high current − − 35 mA IXOL XOUT output low current (@ 0.5 V, VDD = 2.5 V) − 3 − mA IXOH XOUT output high current (@ 1.8 V, VDD = 2.5 V) − 3 − mA VOL Output low voltage (VDD = 2.5 V, IOL = 8 mA) − − 0.6 V VOH Output high voltage (VDD = 2.5 V, IOH = 8 mA) 1.8 − − V IDD Static supply current (Note 1) − 1.0 − mA ICC Dynamic supply current (2.5 V, 10 MHz and no load) − 2.5 − mA 2.375 2.5 2.625 V Power−up time (first locked cycle after power−up) − − 5 mS Output impedance − 50 − W Min Typ Max Unit Input frequency 6 − 12 MHz Output frequency 6 − 12 MHz Input Frequency = 6 MHz − ±1.5 − % Input Frequency = 12 MHz − ±0.8 − VDD tON ZOUT Operating Voltage 1. XIN / CLKIN pin is pulled low. Table 6. AC ELECTRICAL CHARACTERISTICS FOR 2.5 V SUPPLY Symbol CLKIN ModOUT fd Parameter Frequency Deviation tLH (Note 2) Output rise time (measured from 0.7 V to 1.7 V) 0.7 1.4 1.7 nS tHL (Note 2) Output fall time (measured from 1.7 V to 0.7 V) 0.4 0.9 1.1 nS tJC Jitter (Cycle−to−Cycle) − − 200 pS tD Output duty cycle 45 50 55 % 2. tLH and tHL are measured into a capacitive load of 15 pF. http://onsemi.com 4 ASM3P2969A Table 7. DC ELECTRICAL CHARACTERISTICS FOR 3.3 V SUPPLY (Test condition: All parameters are measured at room temperature (+25°C) unless otherwise stated.) Parameter Symbol Min Typ Max Unit VIL Input low voltage VSS−0.3 − 0.8 V VIH Input high voltage 2.0 − VDD+0.3 V IIL Input low current − − −35 mA IIH Input high current − − 35 mA IXOL XOUT output low current (@ 0.4 V, VDD = 3.3 V) − 3 − mA IXOH XOUT output high current (@ 2.5 V, VDD = 3.3 V) − 3 − mA VOL Output low voltage (VDD = 3.3 V, IOL = 8 mA) − − 0.4 V VOH Output high voltage (VDD = 3.3 V, IOH = 8 mA) 2.5 − − V IDD Static supply current (Note 3) − 1.1 − mA ICC Dynamic supply current (3.3 V, 10 MHz and no load) − 3.5 − mA 2.7 3.3 3.6 V Power−up time (first locked cycle after power−up) − − 5 mS Output impedance − 45 − W Min Typ Max Unit Input frequency 6 − 13 MHz Output frequency 6 − 13 MHz % VDD tON ZOUT Operating Voltage 3. XIN / CLKIN pin is pulled low. Table 8. AC ELECTRICAL CHARACTERISTICS FOR 3.3 V SUPPLY Symbol CLKIN ModOUT fd Parameter Frequency Deviation Input Frequency = 6 MHz − ±1.5 − Input Frequency = 13 MHz − ±0.75 − tLH (Note 4) Output rise time (measured from 0.8 V to 2.0 V) 0.4 1.2 1.5 nS tHL (Note 4) Output fall time (measured at 2.0 V to 0.8 V) 0.4 1.0 1.2 nS tJC Jitter (Cycle−to−Cycle) − − 200 pS tD Output duty cycle 45 50 55 % 4. tLH and tHL are measured into a capacitive load of 15 pF. http://onsemi.com 5 ASM3P2969A R1 = 510 W Crystal C1 = 27 pF C2 = 27 pF Figure 3. Typical Crystal Oscillator Circuit Table 9. TYPICAL CRYSTAL SPECIFICATIONS Fundamental AT Cut Parallel Resonant Crystal Nominal frequency 8.000 MHz Frequency tolerance ±50 ppm or better at 25°C Operating temperature range −25°C to +85°C Storage temperature −40°C to +85°C Load capacitance 18 pF Shunt capacitance 7 pF maximum ESR 25 W http://onsemi.com 6 ASM3P2969A PACKAGE DIMENSIONS TSOT−23, 6 LEAD CASE 419AF−01 ISSUE O SYMBOL D MIN NOM A e E1 MAX 1.00 A1 0.01 0.05 0.10 A2 0.80 0.87 0.90 b 0.30 c 0.12 E 0.45 0.15 D 2.90 BSC E 2.80 BSC E1 1.60 BSC e 0.95 TYP L 0.30 L1 0.40 0.20 0.50 0.60 REF L2 0.25 BSC 0º θ 8º TOP VIEW A2 A b q L A1 c L1 SIDE VIEW END VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-193. http://onsemi.com 7 L2 ASM3P2969A PACKAGE DIMENSIONS SOIC 8, 150 mils CASE 751BD−01 ISSUE O E1 E SYMBOL MIN A 1.35 1.75 A1 0.10 0.25 b 0.33 0.51 c 0.19 0.25 D 4.80 5.00 E 5.80 6.20 E1 3.80 4.00 MAX 1.27 BSC e PIN # 1 IDENTIFICATION NOM h 0.25 0.50 L 0.40 1.27 θ 0º 8º TOP VIEW D h A1 θ A c e b L END VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MS-012. http://onsemi.com 8 ASM3P2969A PACKAGE DIMENSIONS TSSOP8, 4.4x3 CASE 948AL−01 ISSUE O b SYMBOL MIN NOM A E1 E MAX 1.20 A1 0.05 A2 0.80 b 0.19 0.30 c 0.09 0.20 D 2.90 3.00 3.10 E 6.30 6.40 6.50 E1 4.30 4.40 4.50 0.15 0.90 e 0.65 BSC L 1.00 REF L1 0.50 θ 0º 0.60 1.05 0.75 8º e TOP VIEW D A2 c q1 A A1 L1 SIDE VIEW L END VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-153. http://onsemi.com 9 ASM3P2969A Table 10. ORDERING INFORMATION Part Number Marking ASM3P2969AF−06OR J4LL ASM3P2969AF−08TT Package Type Temperature 6−Pin TSOT−23, TAPE & REEL, Pb Free Commercial 3P2969AF 8−Pin TSSOP, TUBE, Pb Free Commercial ASM3P2969AF−08TR 3P2969AF 8−Pin TSSOP, TAPE & REEL, Pb Free Commercial ASM3P2969AF−08ST 3P2969AF 8−Pin SOIC, TUBE, Pb Free Commercial ASM3P2969AF−08SR 3P2969AF 8−Pin SOIC, TAPE & REEL, Pb Free Commercial ASM3P2969AG−06OR J3LL 6−Pin TSOT−23, TAPE & REEL, Green Commercial ASM3P2969AG−08TT 3P2969AG 8−Pin TSSOP, TUBE, Green Commercial ASM3P2969AG−08TR 3P2969AG 8−Pin TSSOP, TAPE & REEL, Green Commercial ASM3P2969AG−08ST 3P2969AG 8−Pin SOIC, TUBE, Green Commercial ASM3P2969AG−08SR 3P2969AG 8−Pin SOIC, TAPE & REEL, Green Commercial ASM3I2969AF−06OR J5LL ASM3I2969AF−08TT 6−Pin TSOT−23, TAPE & REEL, Pb Free Industrial 3I2969AF 8−Pin TSSOP, TUBE, Pb Free Industrial ASM3I2969AF−08TR 3I2969AF 8−Pin TSSOP, TAPE & REEL, Pb Free Industrial ASM3I2969AF−08ST 3I2969AF 8−Pin SOIC, TUBE, Pb Free Industrial ASM3I2969AF−08SR 3I2969AF 8−Pin SOIC, TAPE & REEL, Pb Free Industrial ASM3I2969AG−06OR J6LL 6−Pin TSOT−23, TAPE & REEL, Green Industrial ASM3I2969AG−08TT 3I2969AG 8−Pin TSSOP, TUBE, Green Industrial ASM3I2969AG−08TR 3I2969AG 8−Pin TSSOP, TAPE & REEL, Green Industrial ASM3I2969AG−08ST 3I2969AG 8−Pin SOIC, TUBE, Green Industrial ASM3I2969AG−08SR 3I2969AG 8−Pin SOIC, TAPE & REEL, Green Industrial ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 10 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative ASM3P2969A/D