Features • Low-voltage and Standard-voltage Operation ─ 1.8 (VCC = 1.8V to 5.5V) • • • • • • • • • • Internally Organized 512 x 8 (4K), or 1024 x 8 (8K) Two-wire Serial Interface Schmitt Trigger, Filtered Inputs for Noise Suppression Bidirectional Data Transfer Protocol 1 MHz (5V), 400 kHz (1.8V, 2.5V, 2.7V) Compatibility Write Protect Pin for Hardware Data Protection 16-byte Page (4K, 8K) Write Modes Partial Page Writes Allowed Self-timed Write Cycle (5 ms max) High-reliability Two-wire Serial EEPROM 4K (512 x 8) 8K (1024 x 8) ─ Endurance: 1 Million Write Cycles ─ Data Retention: 100 Years • 8-lead PDIP, 8-lead JEDEC SOIC, 8-lead Ultra-Thin Mini-MAP (MLP 2x3), 5-lead SOT23, 8-lead TSSOP and 8-ball dBGA2 Packages • Lead-free/Halogen-free • Die Sales: Wafer Form and Tape and Reel Description The AT24C04B/08B provides 4096/8192 bits of serial electrically erasable and programmable read-only memory (EEPROM) organized as 512/1024 words of 8 bits each. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential. The AT24C04B/08B is available in space-saving 8-lead PDIP, 8-lead JEDEC SOIC, 8-lead Ultra-Thin MiniMAP (MLP 2x3), 5-lead SOT23, 8-lead TSSOP, and 8-ball dBGA2 packages and is accessed via a Two-wire serial interface. In addition, the AT24C04B/08B is available in 1.8V (1.8V to 5.5V) version. AT24C04B AT24C08B Not Recommended for New Design. Replaced by AT24C04C or AT24C08C. Figure 1. Pin Configurations Pin Name A0 – A2 Description Address Inputs SDA Serial Data SCL Serial Clock Input 8-lead Ultra-Thin Mini-MAP (MLP 2x3) VCC 8 1 A0 WP 7 SCL 6 SDA 5 2 A1 3 A2 4 GND 8-ball dBGA2 VCC WP SCL SDA Bottom View WP Write Protect NC No Connect GND Ground VCC Power Supply Note: For use of 5-lead SOT23 4K: The software A2 and A1 bits in the device address word must be set to zero to properly communicate. 8K: The software A2 bit in the device address word must be set to zero to properly communicate. 8 VCC 2 7 3 6 4 5 WP SCL SDA A0 A1 A2 GND 5-lead SOT23 1 GND 2 SDA 3 2 6 5 8-lead SOIC 1 SCL 1 7 Bottom View 8-lead TSSOP A0 A1 A2 GND A0 A1 3 A2 4 GND 8 1 8 2 7 3 6 4 5 VCC WP SCL SDA 8-lead PDIP 5 WP 4 VCC A0 A1 A2 GND 1 2 3 4 8 7 6 5 VCC WP SCL SDA 5226G–SEEPR–11/09 Absolute Maximum Ratings *NOTICE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other condition beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Operating Temperature ..........................−55°C to +125°C Storage Temperature ...........................−65°C to + 150°C Voltage on Any Pin with Respect to Ground .................................. − 0.1V to +7.0V Maximum Operating Voltage ................................... 6.25V DC Output Current ................................................ 5.0 mA Figure 2. Block Diagram VCC GND WP START STOP LOGIC SDA SERIAL CONTROL LOGIC LOAD DEVICE ADDRESS COMPARATOR A2 A1 A0 R/W EN H.V. PUMP/TIMING COMP LOAD DATA RECOVERY INC DATA WORD ADDR/COUNTER Y DEC X DEC SCL EEPROM SERIAL MUX DOUT/ACK LOGIC DIN DOUT 2 AT24C04B/08B 5226G–SEEPR–11/09 Two-wire Serial EEPROM 1. Pin Description SERIAL CLOCK (SCL): The SCL input is used to positive edge clock data into each EEPROM device and negative edge clock data out of each device. SERIAL DATA (SDA): The SDA pin is bidirectional for serial data transfer. This pin is open drain driven and may be wire-ORed with any number of other open-drain or open-collector devices. DEVICE/PAGE ADDRESSES (A2, A1, A0): The AT24C04B uses the A2 and A1 inputs for hard wire addressing and a toal of four 4K devices may be addressed on a single bus system. The A0 pin is a no connect and can be connected to ground (device addressing is discussed in detail under the Device Addressing section). The AT24C08B only uses the A2 input for hardware addressing and a total of two 8K devices may be addressed on a single bus system. The A0 and A1 pins are no connects and can be connected to ground (device addressing is discussed in detail under the Device Addressing section). Table 1. Write Protect WP Pin Status Part of the Array Protected 24C04B/08B At VCC Full Array At GND Normal Read/Write Operations 3 5226G–SEEPR–11/09 2. Memory Organization AT24C04B, 4K SERIAL EEPROM: Internally organized with 32 pages of 16 bytes each, the 4K requires a 9-bit data word address for random word addressing. AT24C08B, 8K SERIAL EEPROM: Internally organized with 64 pages of 16 bytes each, the 8K requires a 10-bit data word address for random word addressing. Table 2. Pin Capacitance(1) Applicable over recommended operating range from TA = 25°C, f = 1.0 MHz, VCC = +1.8V Symbol Test Condition Max Units Conditions CI/O Input/Output Capacitance (SDA) 8 pF VI/O = 0V CIN Input Capacitance (A0, A1, A2, SCL) 6 pF VIN = 0V Note: 1. This parameter is characterized and is not 100% tested. Table 3. DC Characteristics Applicable over recommended operating range from: TAI = –40°C to +85°C, VCC = +1.8V to +5.5V (unless otherwise noted) Symbol Test Condition Min Typ Max Units VCC1 Supply Voltage 1.8 5.5 V VCC2 Supply Voltage 2.5 5.5 V VCC3 Supply Voltage 2.7 5.5 V VCC4 Supply Voltage 4.5 5.5 V ICC Supply Current VCC = 5.0V READ at 100 kHz 0.4 1.0 mA ICC Supply Current VCC = 5.0V WRITE at 100 kHz 2.0 3.0 mA ISB1 Supply Current VCC = 1.8V VIN = VCC or VSS 0.6 3.0 µA ISB2 Supply Current VCC = 2.5V VIN = VCC or VSS 1.4 4.0 µA ISB3 Supply Current VCC = 2.7V VIN = VCC or VSS 1.6 4.0 µA ISB4 Supply Current VCC = 5.0V VIN = VCC or VSS 8.0 18.0 µA ILI Input Leakage Current VIN = VCC or VSS 0.10 3.0 µA ILO Output Leakage Current VOUT = VCC or VSS 0.05 3.0 µA - 0.6 VCC x 0.3 V VCC x 0.7 VCC + 0.5 V (1) VIL Input Low Level VIH Input High Level(1) VOL2 Output Low Level VCC = 3.0V IOL = 2.1 mA 0.4 V VOL1 Output Low Level VCC = 1.8V IOL = 0.15 mA 0.2 V Note: 4 Parameter 1. VIL min and VIH max are reference only and are not tested. AT24C04B/08B 5226G–SEEPR–11/09 Two-wire Serial EEPROM Table 4. AC Characteristics Applicable over recommended operating range from TAI = –40°C to +85°C, VCC = +1.8V to +5.5V, CL = 1 TTL Gate and 100 pF (unless otherwise noted) 1.8, 2.5, 2.7 Symbol 5.0-volt Parameter Units Min Max Min fSCL Clock Frequency, SCL tLOW Clock Pulse Width Low 1.2 0.4 µs tHIGH Clock Pulse Width High 0.6 0.4 µs tI Noise Suppression Time tAA Clock Low to Data Out Valid 0.1 tBUF Time the bus must be free before a new transmission can start 1.2 0.5 µs tHD.STA Start Hold Time 0.6 0.25 µs tSU.STA Start Setup Time 0.6 0.25 µs tHD.DAT Data in Hold Time 0 0 µs tSU.DAT Data In Setup Time 100 100 ns tR Inputs Rise Time(1) 0.3 0.3 µs tF Inputs Fall Time(1) 300 100 ns TSU.STO Stop Setup Time 0.6 .25 µs tDH Data Out Hold Time 50 50 ns tWR Write Cycle Time Endurancec(1) 5.0V, 25°C, Byte Mode Note: 1. 400 Max 1000 50 0.9 40 0.05 5 1M 0.55 5 1M kHz ns µs ms Write cycles This parameter is ensured by characterization only. 5 5226G–SEEPR–11/09 3. Device Operation CLOCK and DATA TRANSITIONS: The SDA pin is normally pulled high with an external device. Data on the SDA pin may change only during SCL low time periods (see Figure 6 ). Data changes during SCL high periods will indicate a start or stop condition as defined below. START CONDITION: A high-to-low transition of SDA with SCL high is a start condition which must precede any other command (see Figure 7). STOP CONDITION: A low-to-high transition of SDA with SCL high is a stop condition. After a read sequence, the stop command will place the EEPROM in a standby power mode (see Figure 7). ACKNOWLEDGE: All addresses and data words are serially transmitted to and from the EEPROM in 8-bit words. The EEPROM sends a zero to acknowledge that it has received each word. This happens during the ninth clock cycle. STANDBY MODE: The AT24C04B/08B features a low-power standby mode which is enabled: (a) Upon power-up and (b) After the receipt of the STOP bit and the completion of any internal operations. 2-WIRE SOFTWARE RESET: After an interruption in protocol, power loss or system reset, 2-wire part can be reset by following these steps: (a) Create a start bit condition, (b) Clock 9 cycles, (c) Create another start bit followed by a stop bit condition as shown below. The device is ready for the next communication after the above steps have been completed. Figure 3. Software reset Dummy Clock Cycles Start bit SCL any 1 2 3 Start bit 8 Stop bit 9 SDA 6 AT24C04B/08B 5226G–SEEPR–11/09 Two-wire Serial EEPROM 4. Bus Timing Figure 4. SCL: Serial Clock, SDA: Serial Data I/O® tHIGH tF tR tLOW tLOW SCL tSU.STA tHD.STA tHD.DAT tSU.DAT tSU.STO SDA IN tAA tDH tBUF SDA OUT 5. Write Cycle Timing Figure 5. SCL: Serial Clock, SDA: Serial Data I/O SCL SDA 8th BIT ACK WORDn twr STOP CONDITION Note: 1. (1) START CONDITION The write cycle time tWR is the time from a valid stop condition of a write sequence to the end of the internal clear/write cycle. 7 5226G–SEEPR–11/09 Figure 6. Data Validity SDA SCL DATA STABLE DATA STABLE DATA CHANGE Figure 7. Start and Stop Definition SDA SCL START Figure 8. STOP Output Acknowledge 1 SCL 8 9 DATA IN DATA OUT START 8 ACKNOWLEDGE AT24C04B/08B 5226G–SEEPR–11/09 Two-wire Serial EEPROM 6. Device Addressing The 4K and 8K EEPROM device requires an 8-bit device address word following a start condition to enable the chip for a read or write operation (refer to Figure 9 ). The device address word consists of a mandatory one, zero sequence for the first four most significant bits as shown. This is common to all the EEPROM devices. The 4K EEPROM only uses the A2 and A1 device address bits with the third bit being a memory page address bit. The two device address bits must compare to their corresponding hard-wired input pins. The A0 pin is no connect. The 8K EEPROM only uses the A2 device address bit with the next 2 bits being for memory page addressing. The A2 must compare to its corresponding hard-wired input pin. The A1 and A0 pins are no connect. For the SOT23 Package Offering: The 4K EEPROM software A2 and A1 bits in the device address word must be set to zero to properly communicate. The 8K EEPROM software A2 bit in the device address word must be set to zero to properly communicate. 7. Write Operations BYTE WRITE: A write operation requires an 8-bit data word address following the device address word and acknowledgment. Upon receipt of this address, the EEPROM will again respond with a zero and then clock in the first 8-bit data word. Following receipt of the 8-bit data word, the EEPROM will output a zero and the addressing device, such as a microcontroller, must terminate the write sequence with a stop condition. At this time the EEPROM enters an internally timed write cycle, tWR, to the nonvolatile memory. All inputs are disabled during this write cycle and the EEPROM will not respond until the write is complete (see Figure 10 ). PAGE WRITE: The 4K/8K EEPROM is capable of an 16-byte page write. A page write is initiated the same as a byte write, but the microcontroller does not send a stop condition after the first data word is clocked in. Instead, after the EEPROM acknowledges receipt of the first data word, the microcontroller can transmit up to fifteen data words. The EEPROM will respond with a zero after each data word received. The microcontroller must terminate the page write sequence with a stop condition. (see Figure 11 ). The data word address lower four bits are internally incremented following the receipt of each data word. The higher data word address bits are not incremented, retaining the memory page row location. When the word address, internally generated, reaches the page boundary, the following byte is placed at the beginning of the same page. If more than sixteen data words are transmitted to the EEPROM, the data word address will “roll over” and previous data will be overwritten. ACKNOWLEDGE POLLING: Once the internally timed write cycle has started and the EEPROM inputs are disabled, acknowledge polling can be initiated. This involves sending a start condition followed by the device address word. The read/write bit is representative of the operation desired. Only if the internal write cycle has completed will the EEPROM respond with a zero allowing the read or write sequence to continue. 9 5226G–SEEPR–11/09 8. Read Operations Read operations are initiated the same way as write operations with the exception that the read/write select bit in the device address word is set to one. There are three read operations: current address read, random address read and sequential read. CURRENT ADDRESS READ: The internal data word address counter maintains the last address accessed during the last read or write operation, incremented by one. This address stays valid between operations as long as the chip power is maintained. The address “roll over” during read is from the last byte of the last memory page to the first byte of the first page. The address “roll over” during write is from the last byte of the current page to the first byte of the same page. Once the device address with the read/write select bit set to one is clocked in and acknowledged by the EEPROM, the current address data word is serially clocked out. The microcontroller does not respond with an input zero but does generate a following stop condition (see Figure 12). RANDOM READ: A random read requires a “dummy” byte write sequence to load in the data word address. Once the device address word and data word address are clocked in and acknowledged by the EEPROM, the microcontroller must generate another start condition. The microcontroller now initiates a current address read by sending a device address with the read/write select bit high. The EEPROM acknowledges the device address and serially clocks out the data word. The microcontroller does not respond with a zero but does generate a following stop condition (see Figure 13). SEQUENTIAL READ: Sequential reads are initiated by either a current address read or a random address read. After the microcontroller receives a data word, it responds with an acknowledge. As long as the EEPROM receives an acknowledge, it will continue to increment the data word address and serially clock out sequential data words. When the memory address limit is reached, the data word address will “roll over” and the sequential read will continue. The sequential read operation is terminated when the microcontroller does not respond with a zero but does generate a following stop condition (see Figure 14 ). Figure 9. 10 Device Address 4K 1 0 1 0 A2 A1 P0 R/W 8K 1 0 1 0 A2 P1 P0 R/W AT24C04B/08B 5226G–SEEPR–11/09 Two-wire Serial EEPROM Figure 10. Byte Write Figure 11. Page Write Figure 12. Current Address Read 11 5226G–SEEPR–11/09 12 Figure 13. Random Read Figure 14. Sequential Read AT24C04B/08B 5226G–SEEPR–11/09 Two-wire Serial EEPROM 9. AT24C04B Ordering Information Table 5. Ordering Information Ordering Code AT24C04B-PU Voltage Package 1.8 8P3 1.8 8S1 (NiPdAu Lead Finish) 1.8 8S1 (NiPdAu Lead Finish) 1.8 8A2 (NiPdAu Lead Finish) 1.8 8A2 (NiPdAu Lead Finish) 1.8 8Y6 1.8 5TS1 (Bulk form only) AT24C04BN-SH-B (1) (NiPdAu Lead Finish) AT24C04BN-SH-T AT24C04B-TH-B AT24C04B-TH-T (2) (1) (2) AT24C04BY6-YH-T AT24C04B-TSU-T (2) (2) AT24C04BU3-UU-T (2) AT24C04B-W-11(3) Note: 1. 2. 3. 1.8 8U3-1 1.8 Die Sale Operational range Lead-free/Halogen-free/ Industrial Temperature (–40°C to 85°C) Industrial Temperature (-40°C to 85°C) “-B” denotes bulk. “-T” denotes tape and reel. SOIC = 4K per reel. TSSOP, Ultra Thin Mini-MAP, SOT23, and dBGA2 = 5K per reel. Available in tape and reel and wafer form; order as SL788 for inkless wafer form. Please contact Serial Interface Marketing. Package Type 8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) 8Y6 8-lead, 2.00 mm x 3.00 mm Body, 0.50 mm Pitch, Ultra Thin Mini-MAP, Dual No Lead Package (DFN), (MLP 2x3 mm) 5TS1 5-lead, 2.90 mm x 1.60 mm Body, Plastic Thin Shrink Small Outline Package (SOT23) 8U3-1 8-ball, die Ball Grid Array Package (dBGA2) Options -1.8 Low-voltage (1.8V to 5.5V) 13 5226G–SEEPR–11/09 10. AT24C08B Ordering Information Table 6. Ordering Information Ordering Code AT24C08B-PU AT24C08BN-SH-B (1) Voltage Package (Bulk form only) 1.8 8P3 (NiPdAu Lead Finish) 1.8 8S1 AT24C08BN-SH-T (2) (NiPdAu Lead Finish) 1.8 8S1 AT24C08B-TH-B(1) (NiPdAu Lead Finish) 1.8 8A2 (NiPdAu Lead Finish) 1.8 8A2 (NiPdAu Lead Finish) 1.8 8Y6 1.8 5TS1 1.8 8U3-1 1.8 Die Sale AT24C08B-TH-T (2) AT24C08BY6-YH-T AT24C08B-TSU-T (2) (2) AT24C08BU3-UU-T (2) (3) AT24C08B-W-11 Note: 1. 2. 3. Operational range Lead-free/Halogen-free/ Industrial Temperature (–40°C to 85°C) Industrial Temperature (-40°C to 85°C) “-B” denotes bulk. “-T” denotes tape and reel. SOIC = 4K per reel. TSSOP, Ultra Thin Mini-MAP, SOT23, and dBGA2 = 5K per reel. Available in tape and reel and wafer form; order as SL788 for inkless wafer form. Please contact Serial Interface Marketing. Package Type 8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8A2 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) 8Y6 8-lead, 2.00 mm x 3.00 mm Body, 0.50 mm Pitch, Ultra Thin Mini-MAP, Dual No Lead Package (DFN), (MLP 2x3 mm) 5TS1 5-lead, 2.90 mm x 1.60 mm Body, Plastic Thin Shrink Small Outline Package (SOT23) 8U3-1 8-ball, die Ball Grid Array Package (dBGA2) Options -1.8 14 Low-voltage (1.8V to 5.5V) AT24C04B/08B 5226G–SEEPR–11/09 Two-wire Serial EEPROM 11. Part Marketing Scheme 11.1. AT24C04B Device Package Marking 8-PDIP Seal Year Top Mark --A --0 * --- Seal Week --- --- --T M L --- --- --4 B Lot Number --- --- --- --- --- --- --U Y W W --- --- --- --1 --- --- --- --- Pin 1 Indicator (Dot) Y = 6: 7: 8: 9: SEAL YEAR 2006 0: 2007 1: 2008 2: 2009 3: 2010 2011 2012 2013 WW = SEAL WEEK 02 = Week 2 04 = Week 4 :: : :::: : :: : :::: :: 50 = Week 50 52 = Week 52 Lot Number to Use ALL Characters in Marking BOTTOM MARK No Bottom Mark Y = 6: 7: 8: 9: SEAL YEAR 2006 0: 2007 1: 2008 2: 2009 3: 2010 2011 2012 2013 8-SOIC Seal Year Top Mark --A --0 * --- --- --- --T M L --- --- --4 B Lot Number --- --- --- Seal Week --- --- --- --H Y W W --- --- --- --1 --- --- --- --- WW = SEAL WEEK 02 = Week 2 04 = Week 4 :: : :::: : :: : :::: :: 50 = Week 50 52 = Week 52 Lot Number to Use ALL Characters in Marking BOTTOM MARK 1 Pin 1 Indicator (Dot) No Bottom Mark 8-TSSOP Top Mark Pin 1 Indicator (Dot) --- --- --- --* H Y W W --- --- --- --- --0 4 B 1 --- --- --- --- --- Y = 6: 7: 8: 9: SEAL YEAR 2006 0: 2007 1: 2008 2: 2009 3: 2010 2011 2012 2013 WW 02 04 :: :: 50 52 = = = : : = = SEAL Week Week :::: :::: Week Week WEEK 2 4 : :: 50 52 Bottom Mark --- --- --- --- --- --- --- --P H --- --- --- --- --- --- --- --A A A A A A A A <- Pin 1 Indicator 15 5226G–SEEPR–11/09 8-Ultra Thin Mini Map Top Mark Y = YEAR OF ASSEMBLY --- --- --0 4 B --- --- --H 1 XX = ATMEL LOT NUMBER TO COORESPOND WITH NSEB TRACE CODE LOG BOOK. (e.g. XX = AA, AB, AC,...AX, AY, AZ) --- --- --Y X X --- --- --* Pin 1 Indicator (Dot) Y = 6: 7: 8: 9: SEAL YEAR 2006 0: 2007 1: 2008 2: 2009 3: 2010 2011 2012 2013 ULA Top Mark --- --- --0 4 B --- --- --Y X X --- --- --* Y 2006 2007 Pin 1 Indicator (Dot) = BUILD YEAR = 6 2008 = 8 = 7 Etc. . . . XX = ATMEL LOT NUMBER TO COORESPOND WITH NSEB TRACE CODE LOG BOOK. (e.g. XX = AA, AB, AC,...AX, AY, AZ) 16 AT24C04B/08B 5226G–SEEPR–11/09 Two-wire Serial EEPROM SOT23 Top Mark Line 1 -----------> XX V W U = = = = --- --- --- --- --4 B 1 B U --- --- --- --- --* Device Voltage Indicator Write Protect Feature Material Set Pin 1 Indicator (Dot) Bottom Mark --- --- --- --Y M T C --- --- --- --Y M = = TC = One Digit Year Code Seal Month (Use Alpha Designator A-L) Trace Code dBGA2 Top Mark Line 1 -----------> Line 2 -----------> XXX U Y M TC = = = = = 04BU YMTC <--- Pin 1 This Corner Device Material Set One Digit Year Code Seal Month (Use Alpha Designator A-L) Trace Code 17 5226G–SEEPR–11/09 11.2. AT24C08B Device Package Marking dBGA2 Top Mark Line 1 -----------> Line 2 -----------> 08BU YMXX <--- Pin 1 This Corner Y = ONE DIGIT YEAR CODE 8: 2008 1: 2011 9: 2009 2: 2012 0: 2010 3: 2013 1 M = A B " J K L SEAL MONTH (USE ALPHA DESIGNATOR A-L) = JANUARY = FEBRUARY " """"""" = OCTOBER = NOVEMBER = DECEMBER XX = TRACE CODE (ATMEL LOT NUMBERS TO CORRESPOND WITH ATK TRACE CODE LOG BOOK) 8-Ultra Thin Mini MAP Top Mark --- --- --0 8 B --- --- --H 1 --- --- --Y X X --- --- --* Pin 1 Indicator (Dot) Y = YEAR OF ASSEMBLY XX = TRACE ATMEL LOT NUMBER TO COORESPOND WITH TRACE CODE LOG BOOK. (e.g. XX = AA, AB, AC,...AX, AY, AZ) Y = SEAL YEAR 6: 2006 7: 2007 8: 2008 9: 2009 18 0: 1: 2: 3: 1 2010 2011 2012 2013 AT24C04B/08B 5226G–SEEPR–11/09 Two-wire Serial EEPROM 8-PDIP and 8-SOIC Seal Year Seal Week Top Mark --A --0 * --- --- --- --T M L --- --- --8 B Lot Number --- --- --- --- --- --- --H Y W W --- --- --- --1 --- --- --- --- Pin 1 Indicator (Dot) Y = SEAL YEAR 8: 2008 9: 2009 0: 2010 1: 2011 1 2: 3: 4: 5: 1 1 WW = SEAL WEEK 2012 02 = Week 2 2013 04 = Week 4 2014 :: : :::: : 2015 :: : :::: :: 50 = Week 50 52 = Week 52 SOT23 Top Mark Line 1 -----------> --- --- --- --- --8 B 1 B U --- --- --- --- --* Pin 1 Indicator (Dot) BACKSIDE MARKING --- --- --- --Y M X X --- --- --- --Y = ONE DIGIT YEAR CODE 4: 2004 7: 2007 5: 2005 8: 2008 6: 2006 9: 2009 M = A B " J K L SEAL MONTH (USE ALPHA DESIGNATOR A-L) = JANUARY = FEBRUARY " """"""" = OCTOBER = NOVEMBER = DECEMBER XX = TRACE CODE (ATMEL LOT NUMBERS TO CORRESPOND WITH TRACE CODE LOG BOOK) 19 5226G–SEEPR–11/09 8-TSSOP Pin 1 Indicator (Dot) --- --- --- --* H Y W W --- --- --- --- --0 8 B 1 --- --- --- --- --Bottom Mark --- --- --- --- --- --- --C O O --- --- --- --- --- --- --A A A A A A A <- Pin 1 Indicator COO = Country of Origin Y = SEAL YEAR 6: 2006 0: 2010 7: 2007 1: 2011 8: 2008 2: 2012 9: 2009 3: 2013 20 WW = 02 04 :: :: 50 52 SEAL WEEK = Week 2 = Week 4 : :::: : : :::: :: = Week 50 = Week 52 AT24C04B/08B 5226G–SEEPR–11/09 Two-wire Serial EEPROM 12. Packaging Information 8P3 – PDIP Figure 15. 8P3 – PDIP E 1 E1 N Top View c eA End View COMMON DIMENSIONS (Unit of Measure = inches) D e D1 A2 A b2 b3 b 4 PLCS Side View L MIN NOM MAX NOTE A – – 0.210 2 A2 0.115 0.130 0.195 b 0.014 0.018 0.022 5 b2 0.045 0.060 0.070 6 b3 0.030 0.039 0.045 6 c 0.008 0.010 0.014 D 0.355 0.365 0.400 D1 0.005 – – 3 E 0.300 0.310 0.325 4 E1 0.240 0.250 0.280 3 SYMBOL e Notes: 0.100 BSC eA L 3 0.300 BSC 0.115 0.130 4 0.150 2 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA, for additional information. 2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion. 6. b2 and b3 maximum dimensions do not include Dambar protrusions. Dambar protrusions shall not exceed 0.010 (0.25 mm). 01/09/02 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) DRAWING NO. REV. 8P3 B 21 5226G–SEEPR–11/09 8S1 – JEDEC SOIC Figure 16. 8S1 – JEDECSOIC C 1 E E1 L N ∅ Top View End View e B COMMON DIMENSIONS (Unit of Measure = mm) A SYMBOL A1 D Side View MIN NOM MAX A 1.35 – 1.75 A1 0.10 – 0.25 b 0.31 – 0.51 C 0.17 – 0.25 D 4.80 – 5.00 E1 3.81 – 3.99 E 5.79 – 6.20 e NOTE 1.27 BSC L 0.40 – 1.27 ∅ 0˚ – 8˚ Note: These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances,datums, etc. 10/7/03 R 22 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) DRAWING NO. 8S1 REV. B AT24C04B/08B 5226G–SEEPR–11/09 Two-wire Serial EEPROM 8A2 – TSSOP Figure 17. 8A2 – TSSOP 3 2 1 Pin 1 indicator this corner E1 E L1 N L Top View End View COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL A b D MIN 2.90 E e D A2 MAX NOTE 3.00 3.10 2, 5 3, 5 6.40 BSC E1 4.30 4.40 4.50 A – – 1.20 A2 0.80 1.00 1.05 b 0.19 – 0.30 e Side View NOM L 4 0.65 BSC 0.45 L1 0.60 0.75 1.00 REF Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimension D and E1 to be determined at Datum Plane H. 5/30/02 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 8A2, 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP) DRAWING NO. 8A2 REV. B 23 5226G–SEEPR–11/09 8Y6 – Mini Map Figure 18. 8Y6 – Mini Map D2 A b (8X) E E2 Pin 1 Index Area Pin 1 ID L (8X) D A2 e (6X) A1 1.50 REF. COMMON DIMENSIONS (Unit of Measure = mm) A3 SYMBOL MIN 2.00 BSC E 3.00 BSC MAX D2 1.40 1.50 1.60 E2 - - 1.40 A - - 0.60 A1 0.0 0.02 0.05 A2 - - 0.55 A3 L b NOTE 0.20 REF 0.20 e Notes: NOM D 0.30 0.40 0.50 BSC 0.20 0.25 0.30 2 1. This drawing is for general information only. Refer to JEDEC Drawing MO-229, for proper dimensions, tolerances, datums, etc. 2. Dimension b applies to metallized terminal and is measured between 0.15 mm and 0.30 mm from the terminal tip. If the terminal has the optional radius on the other end of the terminal, the dimension should not be measured in thatradius area. 3. Soldering the large thermal pad is optional, but not recommended. No electrical connection is accomplished to the device through this pad, so if soldered it should be tied toground 10/16/07 R 24 2325 Orchard Parkway San Jose, CA 95131 DRAWING NO. TITLE 8Y6, 8-lead 2.0 x 3.0 mm Body, 0.50 mm Pitch, Utlra Thin Mini-Map, 8Y6 Dual No Lead Package (DFN) ,(MLP 2x3) REV. D AT24C04B/08B 5226G–SEEPR–11/09 Two-wire Serial EEPROM 5TS1 – SOT23 Figure 19. 5TS1 – SOT23 e1 C 4 5 E1 C L E L1 1 3 2 End View Top View b A2 Seating Plane e A A1 D COMMON DIMENSIONS (Unit of Measure = mm) Side View NOTES: 1. This d rawing is for gene ral information onl y. Refer to JEDEC D rawing MO-193, Variation A B, for additional in formation. 2. Dimension D does not include mold flash, prot rusion s, or gate burrs. Mold flash, prot rusion s, or gate burrs shall not exceed 0.15 mm per end. Dimension E1 does not include inte rlead flash or prot rusion . Inte rlead flash or prot rusion shall not exceed 0.15 mm per sid e. 3. The pa ckage top m ay be smaller than the pa ckage bottom . Dimensions D and E1 are dete rmined at the oute rmost extremes of the plastic body exclusi ve of mold flash, tie bar burrs, gate burrs, and inte rlead flash, but including a ny mismatch bet ween the top and bottom of the plastic bod y. 4. These dimensions apply to the flat section of the lead bet ween 0.08 mm and 0.15 mm from the lead ti p. 5. Dimension "b" does not include Dambar prot rusion . Allowable Dambar protrusion shall be 0.08 mm total in excess of the "b" dimension at maxi mum mate rial condition . The Dambar cannot be located on the l ower radius of the foot. Mini mum space bet ween prot rusion and an adjacent lead shall not be less than 0.07 mm. SYMBOL MIN NOM MAX A – – 1.10 A1 0.00 – 0.10 A2 0.70 0.90 1.00 c 0.08 – 0.20 NOTE 4 D 2.90 BS C 2, 3 E 2.80 BS C 2, 3 E1 1.60 BS C 2, 3 L1 0.60 REF e 0.95 BSC e1 1.90 BSC b 0.30 – 0.50 4, 5 6/25/03 R 1150 E . Cheyenne Mtn . Blvd. Colorado Sp rings, CO 80906 TITLE 5TS1, 5-lead, 1.60 mm Body, Plastic Thin Shrink Small Outline Package (SHRINK SOT) DRAWING NO. PO5TS1 REV. A 25 5226G–SEEPR–11/09 8U3-1 – Dbga2 Figure 20. 8U3-1 – Dbga2 E D 1. b A1 PIN 1 BALL PAD CORNER A2 Top View A Side View PIN 1 BALL PAD CORNER 1 2 3 4 8 7 6 5 (d1) d e COMMON DIMENSIONS (Unit of Measure = mm) (e1) MIN NOM MAX A 0.71 0.81 0.91 A1 0.10 0.15 0.20 A2 0.40 0.45 0.50 b 0.20 0.25 0.30 SYMBOL Bottom Vi ew 8 SOLDER BALLS 1. Dimension “b” is measured at the maximum solder ball diameter. This drawing is for general information only. D 1.50 BSC E 2.00 BSC e 0.50 BSC e1 0.25 REF d 1.00 BSC d1 0.25 REF NOTE 6/24/03 R 26 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE 8U3-1, 8-ball, 1.50 x 2.00 mm Body, 0.50 mm pitch, Small Die Ball Grid Array Package (dBGA2) DRAWING NO. REV. PO8U3-1 A AT24C04B/08B 5226G–SEEPR–11/09 Two-wire Serial EEPROM 13. Revision History Table 7. Revision History Doc. Rev. Date Comments 5226G 07/2012 Not recommended for new design. Use AT24C04C/08C. 5226G 11/2009 Corrected AC Characteristics, TAA minimum value from 0.55 to 0.05 5226F 5/2009 Corrected AT24C08B Part Marking Scheme 5226E 12/2008 Add AT24C08B Device Package Marking Details and removed Bumped wafer offering. 5226D 08/2008 Update into MS Format. 5226D 07/2008 Removed ‘Preliminary’ status 5226C 02/2008 Text changes on page 4 and 9 5226B 08/2007 Updated to new template Updated common Figures Added Package Marking tables 5226A 06/2007 Initial document release 27 5226G–SEEPR–11/09 Headquarters International Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309 78054 Saint-Quentin-enYvelines Cedex France Tel: (33) 1-30-60-70-00 Fax: (33) 1-30-60-71-11 Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Technical Support [email protected] Sales Contact www.atmel.com/contacts Product Contact Web Site www.atmel.com Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN-TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2009 Atmel Corporation. All rights reserved. Atmel®, Atmel logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. 5226G–SEEPR–11/09