TI MSP430F2274-EP Mixed signal microcontroller Datasheet

MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
MIXED SIGNAL MICROCONTROLLER
Check for Samples: MSP430F2274-EP
FEATURES
1
•
•
•
•
•
•
•
•
Low Supply Voltage Range 1.8 V to 3.6 V
Ultralow-Power Consumption
– Active Mode: 270 mA at 1 MHz, 2.2 V
– Standby Mode: 0.7 mA
– Off Mode (RAM Retention): 0.1 mA
Ultrafast Wake-Up From Standby Mode in Less
than 1 ms
16-Bit RISC Architecture, 62.5 ns Instruction
Cycle Time
Basic Clock Module Configurations
– Internal Frequencies up to 16 MHz With
Four Calibrated Frequencies to ±1%
– Internal Very Low Power LF Oscillator
– 32-kHz Crystal
(Available Only from –40°C to 105°C)
– High-Frequency Crystal up to 16 MHz
(Available Only from –40°C to 105°C)
– Resonator
– External Digital Clock Source
– External Resistor
16-Bit Timer_A With Three Capture/Compare
Registers
16-Bit Timer_B With Three Capture/Compare
Registers
Universal Serial Communication Interface
– Enhanced UART Supporting
Auto-Baud-Rate Detection (LIN)
– IrDA Encoder and Decoder
– Synchronous SPI
– I2C™
•
•
•
•
•
•
•
•
•
10-Bit, 200-ksps A/D Converter With Internal
Reference, Sample-and-Hold, and Autoscan
and Data Transfer Controller
Two Configurable Operational Amplifiers
Brownout Detector
Serial Onboard Programming, No External
Programming Voltage Needed Programmable
Code Protection by Security Fuse
Bootstrap Loader
On-Chip Emulation Logic
Family Members Include the MSP430F2274
With 32KB + 256B Flash Memory, 1KB RAM
Available in 40-Pin QFN Package and 38-Pin
Thin Shrink Small-Outline DA Package
For Complete Module Descriptions, Refer to
the MSP430x2xx Family User'sGuide
SUPPORTS DEFENSE, AEROSPACE,
AND MEDICAL APPLICATIONS
•
•
•
•
•
•
•
(1)
Controlled Baseline
One Assembly/Test Site
One Fabrication Site
Available in Military (–55°C/125°C)
Temperature Range (1)
Extended Product Life Cycle
Extended Product-Change Notification
Product Traceability
Custom temperature ranges available
DESCRIPTION
The Texas Instruments MSP430 family of ultralow power microcontrollers consists of several devices featuring
different sets of peripherals targeted for various applications. The architecture, combined with five low power
modes, is optimized to achieve extended battery life in portable measurement applications. The device features a
powerful 16-bit RISC CPU, 16-bit registers, and constant generators that attribute to maximum code efficiency.
The digitally controlled oscillator (DCO) allows wake-up from low-power modes to active mode in less than 1 ms.
The MSP430F2274M series is an ultralow-power mixed signal microcontroller with two built-in 16-bit timers, a
universal serial communication interface, 10-bit A/D converter with integrated reference and data transfer
controller (DTC), two general-purpose operational amplifiers in the MSP430F2274M devices, and 32 I/O pins.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2008–2010, Texas Instruments Incorporated
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
Typical applications include sensor systems that capture analog signals, convert them to digital values, and then
process the data for display or for transmission to a host system. Stand-alone RF sensor front end is another
area of application.
Table 1. ORDERING INFORMATION (1)
TA
–55°C to 125°C
(1)
(2)
PACKAGE (2)
ORDERABLE PART NUMBER
QFN (RHA)
MSP430F2274MRHATEP
DA (TSSOP)
MSP430F2274MDATEP
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
Web site at www.ti.com.
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
DEVICE PINOUTS
DVSS
39 38 37 36 35 34 33 32
1
P1.2/TA1
P1.3/TA2
P1.4/SMCLK/TCK
P1.5/TA0/TMS
P1.6/TA1/TDI/TCLK
TEST/SBWTCK
P1.7/TA2/TDO/TDI
DVCC
DVCC
P2.5/Rosc
RHA PACKAGE
(TOP VIEW)
30
P1.1/TA 0
XOUT /P2.7
2
29
P1.0/TACLK /ADC 10 CLK
XIN /P2.6
3
28
P2.4/TA 2/A4/VREF +/VeREF +/OA 1I0
DVSS
4
27
P2.3/TA 1/A3/VREF -/VeREF -/OA 1I1/OA 1O
RST /NMI /SBWTDIO
5
26
P3.7/A7/OA 1I2
P2.0/ACLK /A0/OA 0I0
6
25
P3.6/A6/OA 0I2
P2.1/TAINCLK /SMCLK /A1/OA 0O
7
24
P3.5/UCA 0RXD /UCA 0SOMI
P2.2/TA 0/A2/OA 0I1
8
23
P3.4/UCA 0TXD /UCA 0SIMO
P3.0/UCB 0STE /UCA 0CLK/A5
9
22
P4.7/TBCLK
21
P4.6/TBOUTH /A15 /OA 1I3
P3.1/UCB 0SIMO /UCB 0SDA
10
M4F2274
MRHATEP
TI YMS
LLLLG4
2
Submit Documentation Feedback
P4.5/TB2/A14/OA0I3
P4.4/TB1/A13/OA1O
P4.3/TB0/A12/OA0O
P4.2/TB2
P4.1/TB1
P4.0/TB0
AVCC
AVSS
P3.3/UCB0CLK/UCA0STE
P3.2/UCB0SOMI/UCB0SCL
12 13 14 15 16 17 18 19
TI = TI
YM = YEAR/MONTH
LLLL = LOT TRACE CODE
S = ASSEMBLY SITE CODE
G4 = RoHS with underscore
O = PIN 1 indicator
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
DA PACKAGE
(TOP VIEW)
TEST/SBWTCK
1
38
P1.7/TA2/TDO/TDI
DVCC
2
37
P1.6/TA1/TDI
P2.5/Rosc
3
36
P1.5/TA0/TMS
DVSS
4
35
P1.4/SMCLK/TCK
XOUT/P2.7
5
34
P1.3/TA2
XIN/P2.6
6
33
P1.2/TA1
RST/NMI/SBWTDIO
7
32
P1.1/TA0
P2.0/ACLK/A0/OA0I0
8
31
P1.0/TACLK/ADC 10CLK
P2.1/TAINCLK/SMCLK/A1/OA00
9
30
P2.4/TA2/A4/VREF+/VeREF+/OA1I0
P2.2/TA0/A2/OA0I1
10
29
P2.3/TA1/A3/VREF-/VeREF-/OA1I1/OA10
P3.0/UCB 0STE/UCA 0CLK/A5
11
28
P3.7/A7/OA1I2
P3.1/UCB 0SIMO/UCB 0SDA
12
27
P3.6/A6/OA0I2
P3.2/UCB 0SOMI/UCB 0SCL
13
26
P3.5/UCA0RXD/UCA0SOMI
P3.3/UCB 0CLK/UCA 0STE
14
25
P3.4/UCA0TXD/UCA0SIMO
AVSS
15
24
P4.7/TBCLK
AVCC
16
23
P4.6/TBOUTH/A15/OA1I3
P4.0/TB0
17
22
P4.5/TB2/A14/OA1I3
P4.1/TB1
18
21
P4.4/TB1/A13/OA1O
P4.2/TB2
19
20
P4.3/TB0/A12/OA0O
FUNCTIONAL BLOCK DIAGRAM
VCC
P1.x/P2.x
VSS
2x8
XIN
P3.x/P4.x
2x8
XOUT
Basic Clock
System+
ACLK
Flash
ADC10
10−Bit
Ports P1/P2
Ports P3/P4
OA0, OA1
32kB
16kB
8kB
SMCLK
MCLK
16MHz
CPU
incl. 16
Registers
RAM
1kB
512B
512B
12
Channels,
Autoscan,
DTC
2 Op Amps
2x8 I/O
pull−up/down
resistors
MAB
MDB
Emulation
(2BP)
JTAG
Interface
2x8 I/O
Interrupt
capability,
pull−up/down
resistors
Timer_B3
Brownout
Protection
Watchdog
WDT+
15/16−Bit
Timer_A3
3 CC
Registers
Spy−Bi Wire
3 CC
Registers,
Shadow
Reg
USCI_A0:
UART/LIN,
IrDA, SPI
USCI_B0:
SPI, I2C
RST/NMI
NOTE: See port schematics section for detailed I/O information.
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
3
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
TERMINAL FUNCTIONS (1)
TERMINAL
DA
NO.
RHA
NO.
I/O
P1.0/TACLK/ADC10CLK
31
29
I/O
General-purpose digital I/O pin
Timer_A, clock signal TACLK input
ADC10, conversion clock
P1.1/TA0
32
30
I/O
General-purpose digital I/O pin
Timer_A, capture: CCI0A input, compare: OUT0 output/BSL
transmit
P1.2/TA1
33
31
I/O
General-purpose digital I/O pin
Timer_A, capture: CCI1A input, compare: OUT1 output
P1.3/TA2
34
32
I/O
General-purpose digital I/O pin
Timer_A, capture: CCI2A input, compare: OUT2 output
P1.4/SMCLK/TCK
35
33
I/O
General-purpose digital I/O pin/SMCLK signal output
Test Clock input for device programming and test
P1.5/TA0/TMS
36
34
I/O
General-purpose digital I/O pin/Timer_A, compare: OUT0 output
Test Mode Select input for device programming and test
P1.6/TA1/TDI/TCLK
37
35
I/O
General-purpose digital I/O pin/Timer_A, compare: OUT1 output
Test Data Input or Test Clock Input for programming and test
P1.7/TA2/TDO/TDI (2)
38
36
I/O
General-purpose digital I/O pin/Timer_A, compare: OUT2 output
Test Data Output or Test Data Input for programming and test
P2.0/ACLK/A0/OA0I0
8
6
I/O
General-purpose digital I/O pin/ACLK output
ADC10, analog input A0 / OA0, analog input I0
P2.1/TAINCLK/SMCLK/A1/
OA0O
9
7
I/O
General-purpose digital I/O pin/Timer_A, clock signal at INCLK
SMCLK signal output
ADC10, analog input A1/OA0, analog output
P2.2/TA0/A2/OA0I1
10
8
I/O
General-purpose digital I/O pin
Timer_A, capture: CCI0B input/BSL receive, compare: OUT0
output
ADC10, analog input A2/OA0, analog input I1
P2.3/TA1/A3/VREF–/VeREF–/
OA1I1/OA1O
29
27
I/O
General-purpose digital I/O pin
Timer_A, capture CCI1B input, compare: OUT1 output
ADC10, analog input A3 / negative reference voltage output/input
OA1, analog input I1/OA1, analog output
P2.4/TA2/A4/VREF+/VeREF+/OA1I0
30
28
I/O
General-purpose digital I/O pin/Timer_A, compare: OUT2 output
ADC10, analog input A4/positive reference voltage output/input
OA1, analog input I0
P2.5/ROSC
3
40
I/O
General-purpose digital I/O pin
Input for external DCO resistor to define DCO frequency
XIN/P2.6
6
3
I/O
Input terminal of crystal oscillator
General-purpose digital I/O pin
XOUT/P2.7
5
2
I/O
Output terminal of crystal oscillator
General-purpose digital I/O pin
P3.0/UCB0STE/UCA0CLK/A5
11
9
I/O
General-purpose digital I/O pin
USCI_B0 slave transmit enable/USCI_A0 clock input/output
ADC10, analog input A5
P3.1/UCB0SIMO/UCB0SDA
12
10
I/O
General-purpose digital I/O pin
USCI_B0 slave in/master out in SPI mode, SDA I2C data in I2C
mode
P3.2/UCB01SOMI/UCB0SCL
13
11
I/O
General-purpose digital I/O pin
USCI_B0 slave out/master in SPI mode, SCL I2C clock in I2C
mode
P3.3/UCB0CLK/UCA0STE
14
12
I/O
General-purpose digital I/O pin
USCI_B0 clock input/output/USCI_A0 slave transmit enable
P3.4/UCA0TXD/UCA0SIMO
25
23
I/O
General-purpose digital I/O pin
USCI_A0 transmit data output in UART mode, slave in/master out
in SPI mode
NAME
(1)
(2)
4
DESCRIPTION
If XOUT/P2.7ca7 is used as an input, excess current flows until P2SEL.7 is cleared. This is due to the oscillator output driver connection
to this pad after reset.
TDO or TDI is selected via JTAG instruction.
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
TERMINAL FUNCTIONS (1) (continued)
TERMINAL
DA
NO.
RHA
NO.
I/O
DESCRIPTION
P3.5/UCA0RXD/UCA0SOMI
26
24
I/O
General-purpose digital I/O pin
USCI_A0 receive data input in UART mode, slave out/master in in
SPI mode
P3.6/A6/OA0I2
27
25
I/O
General-purpose digital I/O pin
ADC10 analog input A6/OA0 analog input I2
P3.7/A7/OA1I2
28
26
I/O
General-purpose digital I/O pin
ADC10 analog input A7/OA1 analog input I2
P4.0/TB0
17
15
I/O
General-purpose digital I/O pin
Timer_B, capture: CCI0A input, compare: OUT0 output
P4.1/TB1
18
16
I/O
General-purpose digital I/O pin
Timer_B, capture: CCI1A input, compare: OUT1 output
P4.2/TB2
19
17
I/O
General-purpose digital I/O pin
Timer_B, capture: CCI2A input, compare: OUT2 output
P4.3/TB0/A12/OA0O
20
18
I/O
General-purpose digital I/O pin
Timer_B, capture: CCI0B input, compare: OUT0 output
ADC10 analog input A12/OA0 analog output
P4.4/TB1A13/OA1O
21
19
I/O
General-purpose digital I/O pin
Timer_B, capture: CCI1B input, compare: OUT1 output
ADC10 analog input A13/OA1 analog output
P4.5/TB2A14/OA0I3
22
20
I/O
General-purpose digital I/O pin
Timer_B, compare: OUT2 output
ADC10 analog input A14/OA0 analog input I3
P4.6/TBOUTHA15/OA1I3
23
21
I/O
General-purpose digital I/O pin
Timer_B, switch all TB0 to TB3 outputs to high impedance
ADC10 analog input A15/OA1 analog input I3
P4.7/TBCLK
24
22
I/O
General-purpose digital I/O pin
Timer_B, clock signal TBCLK input
RST/NMI/SBWTDIO
7
5
I
Reset or nonmaskable interrupt input
Spy-Bi-Wire test data input/output during programming and test
TEST/SBWTCK
1
37
I
Selects test mode for JTAG pins on Port1. The device protection
fuse is connected to TEST.
Spy-Bi-Wire test clock input during programming and test
DVCC
2
38, 39
Digital supply voltage
AVCC
16
14
Analog supply voltage
DVSS
4
1, 4
Digital ground reference
AVSS
15
13
Analog ground reference
NA
Package
Pad
NAME
QFN Pad
NA
QFN package pad connection to DVSS recommended.
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
5
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
SHORT-FORM DESCRIPTION
CPU
The MSP430 CPU has a 16-bit RISC architecture
that is highly transparent to the application. All
operations, other than program-flow instructions, are
performed as register operations in conjunction with
seven addressing modes for source operand and four
addressing modes for destination operand.
Program Counter
PC/R0
Stack Pointer
SP/R1
Status Register
SR/CG1/R2
Constant Generator
CG2/R3
General-Purpose Register
R4
General-Purpose Register
R5
General-Purpose Register
R6
General-Purpose Register
R7
General-Purpose Register
R8
Peripherals are connected to the CPU using data,
address, and control buses, and can be handled with
all instructions.
General-Purpose Register
R9
General-Purpose Register
R10
Instruction Set
General-Purpose Register
R11
The instruction set consists of 51 instructions with
three formats and seven address modes. Each
instruction can operate on word and byte data.
Table 2 shows examples of the three types of
instruction formats; the address modes are listed in
Table 3.
General-Purpose Register
R12
General-Purpose Register
R13
General-Purpose Register
R14
General-Purpose Register
R15
The CPU is integrated with 16 registers that provide
reduced
instruction
execution
time.
The
register-to-register operation execution time is one
cycle of the CPU clock.
Four of the registers, R0 to R3, are dedicated as
program counter, stack pointer, status register, and
constant generator respectively. The remaining
registers are general-purpose registers.
Table 2. Instruction Word Formats
Dual operands, source-destination
e.g., ADD R4,R5
R4 + R5 → R5
Single operands, destination only
e.g., CALL R8
PC → (TOS), R8 → PC
Relative jump, un/conditional
e.g., JNE
Jump-on-equal bit = 0
Table 3. Address Mode Descriptions
ADDRESS MODE
(1)
(2)
6
S
(1)
D
(2)
SYNTAX
EXAMPLE
OPERATION
Register
•
•
MOV Rs,Rd
MOV R10,R11
R10 → R11
MOV 2(R5),6(R6)
M(2+R5) → M(6+R6)
Indexed
•
•
MOV X(Rn),Y(Rm)
Symbolic (PC relative)
•
•
MOV EDE,TONI
M(EDE) → M(TONI)
Absolute
•
•
MOV &MEM,&TCDAT
M(MEM) → M(TCDAT)
Indirect
•
MOV @Rn,Y(Rm)
MOV @R10,Tab(R6)
M(R10) → M(Tab+R6)
Indirect autoincrement
•
MOV @Rn+,Rm
MOV @R10+,R11
M(R10) → R11
R10 + 2 → R10
Immediate
•
MOV #X,TONI
MOV #45,TONI
#45 → M(TONI)
S = source
D = destination
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
Operating Modes
The MSP430 has one active mode and five software selectable low-power modes of operation. An interrupt
event can wake up the device from any of the five low-power modes, service the request and restore back to the
low-power mode on return from the interrupt program.
The following six operating modes can be configured by software:
• Active mode ( AM)
– All clocks are active.
• Low-power mode 0 (LPM0)
– CPU is disabled.
ACLK and SMCLK remain active. MCLK is disabled.
• Low-power mode 1 (LPM1)
– CPU is disabled ACLK and SMCLK remain active. MCLK is disabled.
DCO's dc-generator is disabled if DCO not used in active mode.
• Low-power mode 2 (LPM2)
– CPU is disabled.
MCLK and SMCLK are disabled.
DCO's dc-generator remains enabled.
ACLK remains active.
• Low-power mode 3 (LPM3)
– CPU is disabled.
MCLK and SMCLK are disabled.
DCO's dc-generator is disabled.
ACLK remains active.
• Low-power mode 4 (LPM4)
– CPU is disabled.
ACLK is disabled.
MCLK and SMCLK are disabled.
DCO's dc-generator is disabled.
Crystal oscillator is stopped.
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
7
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
Interrupt Vector Addresses
The interrupt vectors and the power-up starting address are located in the address range of 0FFFFh–0FFC0h.
The vector contains the 16-bit address of the appropriate interrupt handler instruction sequence.
If the reset vector (located at address 0FFFEh) contains 0FFFFh (e.g., flash is not programmed), the CPU goes
into LPM4 immediately after power up.
INTERRUPT SOURCE
INTERRUPT FLAG
Power up
External reset
Watchdog
Flash key violation
PC out-of-range (1)
PORIFG
RSTIFG
WDTIFG
KEYV
NMI
Oscillator fault
Flash memory access violation
(6)
8
Reset
0FFFEh
31, highest
(non)-maskable,
(non)-maskable,
(non)-maskable
0FFFCh
30
(2)
NMIIFG
OFIFG
ACCVIFG (2)
(3)
maskable
0FFFAh
29
Timer_B3
TBCCR1 and TBCCR2
CCIFGs, TBIFG (2) (4)
maskable
0FFF8h
28
0FFF6h
27
Watchdog Timer
WDTIFG
maskable
0FFF4h
26
Timer_A3
TACCR0 CCIFG (4)
maskable
0FFF2h
25
Timer_A3
TACCR1 CCIFG,
TACCR2 CCIFG,
TAIFG (2) (4)
maskable
0FFF0h
24
USCI_A0/USCI_B0 Receive
UCA0RXIFG, UCB0RXIFG (2)
maskable
0FFEEh
23
USCI_A0/USCI_B0 Transmit
UCA0TXIFG, UCB0TXIFG (2)
maskable
0FFECh
22
maskable
0FFEAh
21
0FFE8h
20
I/O Port P1 (eight flags)
(4)
(5)
PRIORITY
TBCCR0 CCIFG (4)
I/O Port P2 (eight flags)
(2)
(3)
WORD ADDRESS
Timer_B3
ADC10
(1)
SYSTEM
INTERRUPT
ADC10IFG
(4)
P2IFG.6 to P2IFG.7 (2)
P1IFG.0 to P1IFG.7
(4)
maskable
0FFE6h
19
(2) (4)
maskable
0FFE4h
18
0FFE2h
17
0FFE0h
16
(5)
0FFDEh
15
(6)
0FFDCh ... 0FFC0h
14 ... 0, lowest
A reset is generated if the CPU tries to fetch instructions from within the module register memory address range (0h–01FFh) or from
within unused address range.
Multiple source flags
(non)-maskable: the individual interrupt-enable bit can disable an interrupt event, but the general interrupt enable cannot.
Nonmaskable: neither the individual nor the general interrupt-enable bit disables an interrupt event.
Interrupt flags are located in the module.
This location is used as bootstrap loader security key (BSLSKEY). A 0AA55h at this location disables the BSL completely. A zero (0h)
disables the erasure of the flash if an invalid password is supplied.
The interrupt vectors at addresses 0FFDCh to 0FFC0h are not used in this device and can be used for regular program code if
necessary.
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
Special Function Registers
Most interrupt and module enable bits are collected into the lowest address space. Special function register bits
not allocated to a functional purpose are not physically present in the device. Simple software access is provided
with this arrangement.
Interrupt Enable 1 and 2
Address
7
6
00h
5
4
ACCVIE
rw-0
3
2
1
0
NMIIE
OFIE
WDTIE
rw-0
rw-0
rw-0
WDTIE:
Watchdog Timer interrupt enable. Inactive if watchdog mode is selected. Active if Watchdog Timer
is configured in interval timer mode.
OFIE:
Oscillator fault enable
NMIIE:
(Non)maskable interrupt enable
ACCVIE:
Flash access violation interrupt enable
Address
7
6
5
4
01h
UCA0RXIE
USCI_A0 receive-interrupt enable
UCA0TXIE
USCI_A0 transmit-interrupt enable
UCB0RXIE
USCI_B0 receive-interrupt enable
UCB0TXIE
USCI_B0 transmit-interrupt enable
3
2
1
0
UCB0TXIE
UCB0RXIE
UCA0TXIE
UCA0RXIE
rw-0
rw-0
rw-0
rw-0
Interrupt Flag Register 1 and 2
Address
7
6
5
02h
4
3
2
1
0
NMIIFG
RSTIFG
PORIFG
OFIFG
WDTIFG
rw-0
rw-(0)
rw-(1)
rw-1
rw-(0)
WDTIFG: Set on Watchdog Timer overflow (in watchdog mode) or security key violation.
Reset on VCC power-up or a reset condition at RST/NMI pin in reset mode.
OFIFG:
Flag set on oscillator fault
RSTIFG:
External reset interrupt flag. Set on a reset condition at RST/NMI pin in reset mode. Reset on VCC
power up.
PORIFG: Power-On Reset interrupt flag. Set on VCC power up.
NMIIFG:
Address
Set via RST/NMI-pin
7
6
5
03h
4
3
2
1
0
UCB0
TXIFG
UCB0
RXIFG
UCA0
TXIFG
UCA0
RXIFG
rw-1
rw-0
rw-1
rw-0
UCA0RXIFG USCI_A0 receive-interrupt flag
UCA0TXIFG USCI_A0 transmit-interrupt flag
UCB0RXIFG USCI_B0 receive-interrupt flag
UCB0TXIFG USCI_B0 transmit-interrupt flag
xxx
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
9
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
Legend:
rw:
Bit can be read and written.
rw-0, 1:
Bit can be read and written. It is Reset or Set by PUC.
rw-(0), (1):
Bit can be read and written. It is Reset or Set by POR.
SFR bit is not present in device.
Memory Organization
MSP430F223x
MSP430F225x
MSP430F227x
Memory
Main: interrupt vector
Main: code memory
Size
Flash
Flash
8KB Flash
0FFFFh–0FFC0h
0FFFFh–0E000h
16KB Flash
0FFFFh–0FFC0h
0FFFFh–0C000h
32KB Flash
0FFFFh–0FFC0h
0FFFFh–08000h
Information memory
Size
Flash
256 Byte
010FFh–01000h
256 Byte
010FFh–01000h
256 Byte
010FFh–01000h
Boot memory
Size
ROM
1KB
0FFFh–0C00h
1KB
0FFFh–0C00h
1KB
0FFFh–0C00h
Size
512 Byte
03FFh–0200h
512 Byte
03FFh–0200h
1KB
05FFh–0200h
16-bit
8-bit
8-bit SFR
01FFh–0100h
0FFh–010h
0Fh–00h
01FFh–0100h
0FFh–010h
0Fh–00h
01FFh–0100h
0FFh–010h
0Fh–00h
RAM
Peripherals
Bootstrap Loader (BSL)
The MSP430 bootstrap loader (BSL) enables users to program the flash memory or RAM using a UART serial
interface. Access to the MSP430 memory via the BSL is protected by user-defined password. For complete
description of the features of the BSL and its implementation, see the application report, Features of the MSP430
Bootstrap Loader, TI literature number SLAA089.
BSL Function
DA Package Pins
RHA Package Pins
Data Transmit
32 - P1.1
30 – P1.1
Data Receive
10 - P2.2
8 – P2.2
Flash Memory
The flash memory can be programmed via the Spy-Bi-Wire/JTAG port, or in-system by the CPU. The CPU can
perform single-byte and single-word writes to the flash memory. Features of the flash memory include:
• Flash memory has n segments of main memory and four segments of information memory (A to D) of 64
bytes each. Each segment in main memory is 512 bytes in size.
• Segments 0 to n may be erased in one step, or each segment may be individually erased.
• Segments A to D can be erased individually, or as a group with segments 0–n.
Segments A to D are also called information memory.
• Segment A contains calibration data. After reset segment A is protected against programming and erasing. It
can be unlocked but care should be taken not to erase this segment if the device-specific calibration data is
required.
10
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
Peripherals
Peripherals are connected to the CPU through data, address, and control busses and can be handled using all
instructions. For complete module descriptions, refer to the MSP430x2xx Family User's Guide.
Oscillator and System Clock
The clock system is supported by the basic clock module that includes support for a 32768-Hz watch crystal
oscillator, an internal very low power, low frequency oscillator and an internal digitally-controlled oscillator (DCO).
The basic clock module is designed to meet the requirements of both low system cost and low-power
consumption. The internal DCO provides a fast turn-on clock source and stabilizes in less than 1 ms. The basic
clock module provides the following clock signals:
• Auxiliary clock (ACLK), sourced either from a 32768-Hz watch crystal or the internal LF oscillator for –40°C to
105°C operation. For > 105°C, use external clock source.
• Main clock (MCLK), the system clock used by the CPU
• Sub-Main clock (SMCLK), the sub-system clock used by the peripheral modules
DCO Calibration Data (provided from factory in flash info memory segment A)
DCO Frequency
1 MHz
8 MHz
12 MHz
16 MHz
Calibration Register
Size
Address
CALBC1_1MHZ
byte
010FFh
CALDCO_1MHZ
byte
010FEh
CALBC1_8MHZ
byte
010FDh
CALDCO_8MHZ
byte
010FCh
CALBC1_12MHZ
byte
010FBh
CALDCO_12MHZ
byte
010FAh
CALBC1_16MHZ
byte
010F9h
CALDCO_16MHZ
byte
010F8h
Brownout
The brownout circuit is implemented to provide the proper internal reset signal to the device during power on and
power off.
Digital I/O
There are four 8-bit I/O ports implemented – ports P1, P2, P3, and P4:
• All individual I/O bits are independently programmable.
• Any combination of input, output, and interrupt condition is possible.
• Edge-selectable interrupt input capability for all the eight bits of port P1 and P2.
• Read/write access to port-control registers is supported by all instructions.
• Each I/O has an individually programmable pullup/pulldown resistor.
WDT+ Watchdog Timer
The primary function of the watchdog timer (WDT+) module is to perform a controlled system restart after a
software problem occurs. If the selected time interval expires, a system reset is generated. If the watchdog
function is not needed in an application, the module can be disabled or configured as an interval timer and can
generate interrupts at selected time intervals.
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
11
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
Timer_A3
Timer_A3 is a 16-bit timer/counter with three capture/compare registers. Timer_A3 can support multiple
capture/compares, PWM outputs, and interval timing. Timer_A3 also has extensive interrupt capabilities.
Interrupts may be generated from the counter on overflow conditions and from each of the capture/compare
registers.
Timer_A3 Signal Connections
Input Pin Number
DA
RHA
Device
Input
Signal
31 - P1.0
29 - P1.0
TACLK
TACLK
ACLK
ACLK
SMCLK
SMCLK
Module
Block
Module
Output
Signal
Timer
NA
Output Pin Number
DA
RHA
30 - P1.1
9 - P2.1
7 - P2.1
TAINCLK
INCLK
32 - P1.1
30 - P1.1
TA0
CCI0A
32 - P1.1
10 - P2.2
8 - P2.2
TA0
CCI0B
10 - P2.2
8 - P2.2
VSS
GND
36 - P1.5
34 - P1.5
CCR0
TA0
VCC
VCC
33 - P1.2
31 - P1.2
TA1
CCI1A
33 - P1.2
31 - P1.2
29 - P2.3
27 - P2.3
TA1
CCI1B
29 - P2.3
27 - P2.3
37 - P1.6
35 - P1.6
34 - P1.3
32 - P1.3
30 - P2.4
28 - P2.4
38 - P1.7
36 - P1.7
34 - P1.3
12
Module
Input
Name
32 - P1.3
Submit Documentation Feedback
VSS
GND
VCC
VCC
TA2
CCI2A
ACLK
(internal)
CCI2B
VSS
GND
VCC
VCC
CCR1
CCR2
TA1
TA2
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
Timer_B3
Timer_B3 is a 16-bit timer/counter with three capture/compare registers. Timer_B3 can support multiple
capture/compares, PWM outputs, and interval timing. Timer_B3 also has extensive interrupt capabilities.
Interrupts may be generated from the counter on overflow conditions and from each of the capture/compare
registers.
Timer_B3 Signal Connections
Input Pin Number
DA
RHA
Device
Input
Signal
24 - P4.7
22 - P4.7
TBCLK
Module
Input
Name
TBCLK
ACLK
ACLK
SMCLK
SMCLK
Module
Block
Module
Output
Signal
Timer
NA
Output Pin Number
DA
RHA
24 - P4.7
22 - P4.7
TBCLK
INCLK
17 - P4.0
15 - P4.0
TB0
CCI0A
17 - P4.0
15 - P4.0
20 - P4.3
18 - P4.3
TB0
CCI0B
20 - P4.3
18 - P4.3
VSS
GND
CCR0
TB0
VCC
VCC
18 - P4.1
16 - P4.1
TB1
CCI1A
18 - P4.1
16 - P4.1
21 - P4.4
19 - P4.4
TB1
CCI1B
21 - P4.4
19 - P4.4
VSS
GND
19 - P4.2
17 - P4.2
22 - P4.5
20 - P4.5
19 - P4.2
17 - P4.2
VCC
VCC
TB2
CCI2A
ACLK
(internal)
CCI2B
VSS
GND
VCC
VCC
CCR1
CCR2
TB1
TB2
USCI
The universal serial communication interface (USCI) module is used for serial data communication. The USCI
module supports synchronous communication protocols like SPI (3 or 4 pin), I2C and asynchronous
communication protocols like UART, enhanced UART with automatic baud-rate detection (LIN), and IrDA.
USCI_A0 provides support for SPI (3 or 4 pin), UART, enhanced UART and IrDA.
USCI_B0 provides support for SPI (3 or 4 pin) and I2C.
ADC10
The ADC10 module supports fast, 10-bit analog-to-digital conversions. The module implements a 10-bit SAR
core, sample select control, reference generator and data transfer controller, or DTC, for automatic conversion
result handling allowing ADC samples to be converted and stored without any CPU intervention.
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
13
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
Operational Amplifier (OA)
The MSP430F2274M has two configurable low-current general-purpose operational amplifiers. Each OA input
and output terminal is software-selectable and offer a flexible choice of connections for various applications. The
OA op amps primarily support front-end analog signal conditioning prior to analog-to-digital conversion.
OA0 Signal Connections
Analog Input
Pin Number
DA
RHA
Device Input Signal
Module Input Name
8 - A0
6 - A0
OA0I0
OAxI0
10 - A2
8 - A2
OA0I1
OA0I1
10 - A2
8 - A2
OA0I1
OAxI1
27 - A6
25 - A6
OA0I2
OAxIA
22 - A14
20 - A14
OA0I3
OAxIB
xxxx
OA1 Signal Connections
Analog Input
Pin Number
14
Device Input Signal
Module Input Name
DA
RHA
30 - A4
28 - A4
OA0I0
OAxI0
10 - A2
8 - A2
OA0I1
OA0I1
29 - A3
27 - A3
OA0I1
OAxI1
28 - A7
26 - A7
OA0I2
OAxIA
23 - A15
21 - A15
OA0I3
OAxIB
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
Peripheral File Map
PERIPHERALS WITH WORD ACCESS
ADC10
ADC
ADC
ADC
ADC
ADC
ADC
ADC
ADC
Timer_B
data transfer start address
memory
control register 1
control register 0
analog enable 0
analog enable 1
data transfer control register 1
data transfer control register 0
ADC10SA
ADC10MEM
ADC10CTL1
ADC10CTL0
ADC10AE0
ADC10AE1
ADC10DTC1
ADC10DTC0
1BCh
1B4h
1B2h
1B0h
04Ah
04Bh
049h
048h
Capture/compare register
Capture/compare register
Capture/compare register
Timer_B register
Capture/compare control
Capture/compare control
Capture/compare control
Timer_B control
Timer_B interrupt vector
TBCCR2
TBCCR1
TBCCR0
TBR
TBCCTL2
TBCCTL1
TBCCTL0
TBCTL
TBIV
0196h
0194h
0192h
0190h
0186h
0184h
0182h
0180h
011Eh
Timer_A
Capture/compare register
Capture/compare register
Capture/compare register
Timer_A register
Capture/compare control
Capture/compare control
Capture/compare control
Timer_A control
Timer_A interrupt vector
TACCR2
TACCR1
TACCR0
TAR
TACCTL2
TACCTL1
TACCTL0
TACTL
TAIV
0176h
0174h
0172h
0170h
0166h
0164h
0162h
0160h
012Eh
Flash Memory
Flash control 3
Flash control 2
Flash control 1
FCTL3
FCTL2
FCTL1
012Ch
012Ah
0128h
Watchdog Timer+
Watchdog/timer control
WDTCTL
0120h
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
15
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
PERIPHERALS WITH BYTE ACCESS
OA1
Operational Amplifier 1 control register 1
Operational Amplifier 1 control register 1
OA1CTL1
OA1CTL0
0C3h
0C2h
OA0
Operational Amplifier 0 control register 1
Operational Amplifier 0 control register 1
OA0CTL1
OA0CTL0
0C1h
0C0h
USI_B0
USCI_B0 transmit buffer
USCI_B0 receive buffer
USCI_B0 status
USCI_B0 bit rate control 1
USCI_B0 bit rate control 0
USCI_B0 control 1
USCI_B0 control 0
USCI_B0 I2C slave address
USCI_B0 I2C own address
UCB0TXBUF
UCB0RXBUF
UCB0STAT
UCB0BR1
UCB0BR0
UCB0CTL1
UCB0CTL0
UCB0SA
UCB0OA
06Fh
06Eh
06Dh
06Bh
06Ah
069h
068h
011Ah
0118h
USI_A0
USCI_A0 transmit buffer
USCI_A0 receive buffer
USCI_A0 status
USCI_A0 modulation control
USCI_A0 baud rate control 1
USCI_A0 baud rate control 0
USCI_A0 control 1
USCI_A0 control 0
USCI_A0 IrDA receive control
USCI_A0 IrDA transmit control
USCI_A0 auto baud rate control
UCA0TXBUF
UCA0RXBUF
UCA0STAT
UCA0MCTL
UCA0BR1
UCA0BR0
UCA0CTL1
UCA0CTL0
UCA0IRRCTL
UCA0IRTCTL
UCA0ABCTL
067h
066h
065h
064h
063h
062h
061h
060h
05Fh
05Eh
05Dh
Basic Clock System+
Basic clock system control 3
Basic clock system control 2
Basic clock system control 1
DCO clock frequency control
BCSCTL3
BCSCTL2
BCSCTL1
DCOCTL
053h
058h
057h
056h
Port P4
Port P4 resistor enable
Port P4 selection
Port P4 direction
Port P4 output
Port P4 input
P4REN
P4SEL
P4DIR
P4OUT
P4IN
011h
01Fh
01Eh
01Dh
01Ch
Port P3
Port P3 resistor enable
Port P3 selection
Port P3 direction
Port P3 output
Port P3 input
P3REN
P3SEL
P3DIR
P3OUT
P3IN
010h
01Bh
01Ah
019h
018h
Port P2
Port P2 resistor enable
Port P2 selection
Port P2 interrupt enable
Port P2 interrupt edge select
Port P2 interrupt flag
Port P2 direction
Port P2 output
Port P2 input
P2REN
P2SEL
P2IE
P2IES
P2IFG
P2DIR
P2OUT
P2IN
02Fh
02Eh
02Dh
02Ch
02Bh
02Ah
029h
028h
Port P1
Port P1 resistor enable
Port P1 selection
Port P1 interrupt enable
Port P1 interrupt edge select
Port P1 interrupt flag
Port P1 direction
Port P1 output
Port P1 input
P1REN
P1SEL
P1IE
P1IES
P1IFG
P1DIR
P1OUT
P1IN
027h
026h
025h
024h
023h
022h
021h
020h
Special Function
SFR
SFR
SFR
SFR
IFG2
IFG1
IE2
IE1
003h
002h
001h
000h
16
Submit Documentation Feedback
interrupt flag 2
interrupt flag 1
interrupt enable 2
interrupt enable 1
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
Absolute Maximum Ratings (1)
VALUE
UNIT
Voltage applied at VCC to VSS
–0.3 to 4.1
V
Voltage applied to any pin (2)
–0.3 to VCC + 0.3
V
Diode current at any device terminal
Storage temperature, Tstg (unprogrammed device (3))
Storage temperature, Tstg (programmed device
(1)
(2)
(3)
(3)
)
±2
mA
–55 to 150
°C
–55 to 125
°C
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages referenced to VSS. The JTAG fuse-blow voltage, VFB, is allowed to exceed the absolute maximum rating. The voltage is
applied to the TEST pin when blowing the JTAG fuse.
Higher temperature may be applied during board soldering process according to the current JEDEC J-STD-020 specification with peak
reflow temperatures not higher than classified on the device label on the shipping boxes or reels.
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
17
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
Recommended Operating Conditions (1)
(2)
MIN
VCC
UNIT
3.6
V
Supply voltage during program/erase flash memory
2.2
3.6
V
–55
125
°C
VCC = 1.8 V, Duty Cycle = 50% ±10%
dc
4.15
VCC = 2.7 V, Duty Cycle = 50% ±10%
dc
12
VCC ≥ 3.3 V, Duty Cycle = 50% ±10%
dc
16
Supply voltage
TA
Operating free-air temperature range
0
Processor frequency fSYSTEM
(Maximum MCLK frequency) (1)
(see Figure 1)
(2)
MAX
1.8
VSS
(1)
NOM
Supply voltage during program execution
(2)
V
MHz
The MSP430 CPU is clocked directly with MCLK. Both the high and low phase of MCLK must not exceed the pulse width of the
specified maximum frequency.
Modules might have a different maximum input clock specification. Refer to the specification of the respective module in this data sheet.
System Frequency −MHz
16 MHz
12 MHz
7.5 MHz
4.15 MHz
1.8 V
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
2.2 V
2.7 V
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
Legend:
Supply voltage range,
during flash memory
programming
Supply voltage range,
during program execution
3.3 V 3.6 V
Supply Voltage −V
NOTE: Minimum processor frequency is defined by system clock. Flash program or erase operations require a minimum VCC
of 2.2 V.
Figure 1. Operating Area
18
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
Active-Mode Supply Current (Into DVCC + AVCC) Excluding External Current – Electrical
Characteristics (1) (2)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
IAM,
IAM,
IAM,
TA
VCC
1MHz
fDCO = fMCLK = fSMCLK = 1 MHz,
fACLK = 32,768 Hz,
Program executes in flash,
Active-mode (AM)
BCSCTL1 = CALBC1_1 MHZ,
current (1 MHz)
DCOCTL = CALDCO_1 MHZ,
CPUOFF = 0, SCG0 = 0, SCG1 = 0,
OSCOFF = 0
1MHz
fDCO = fMCLK = fSMCLK = 1 MHz,
fACLK = 32,768 Hz,
Program executes in RAM,
Active-mode (AM)
BCSCTL1 = CALBC1_1 MHZ,
current (1 MHz)
DCOCTL = CALDCO_1 MHZ,
CPUOFF = 0, SCG0 = 0, SCG1 = 0,
OSCOFF = 0
–55°C to 85°C
4kHz
fMCLK = fSMCLK = fACLK = 32,768 Hz/8 = 4,096
Hz,
fDCO = 0 Hz,
Active-mode (AM) Program executes in flash,
current (4 kHz)
SELMx = 11, SELS = 1,
DIVMx = DIVSx = DIVAx = 11,
CPUOFF = 0, SCG0 = 1, SCG1 = 0,
OSCOFF = 0
fMCLK = fSMCLK = fDCO(0, 0) Ⅹ 100 kHz,
fACLK = 0 Hz,
Active-mode (AM) Program executes in flash,
current (100 kHz) RSELx = 0, DCOx = 0,
CPUOFF = 0, SCG0 = 0, SCG1 = 0,
OSCOFF = 1
–55°C to 85°C
IAM,100kHz
(1)
(2)
TEST CONDITIONS
–55°C to 125°C
MIN
TYP MAX
2.2 V
270
390
3V
390
550
2.2 V
240
3V
340
5
2.2 V
125°C
6
3V
60
9
10
mA
85
95
–55°C to 85°C
72
3V
125°C
mA
20
2.2 V
125°C
mA
18
–55°C to 85°C
125°C
UNIT
mA
95
125
All inputs are tied to 0 V or VCC. Outputs do not source or sink any current.
For TA < 105°C, the currents are characterized with a Micro Crystal CC4V-T1A SMD crystal with a load capacitance of 9 pF.
The internal and external load capacitance is chosen to closely match the required 9 pF. For TA > 105°C, the currents are characterized
using a 32-kHz external clock source for ACLK..
Typical Characteristics – Active-Mode Supply Current (Into DVCC + AVCC)
5.0
8.0
fDCO = 16 MHz
TA = 85 °C
Active Mode Current − mA
Active Mode Current − mA
7.0
6.0
fDCO = 12 MHz
5.0
4.0
fDCO = 8 MHz
3.0
2.0
4.0
TA = 25 °C
3.0
VCC = 3 V
2.0
TA = 85 °C
TA = 25 °C
1.0
1.0
0.0
1.5
VCC = 2.2 V
fDCO = 1 MHz
2.0
2.5
3.0
3.5
4.0
0.0
0.0
VCC − Supply Voltage − V
Figure 2. Active-Mode Current vs VCC, TA = 25°C
4.0
8.0
12.0
16.0
fDCO − DCO Frequency − MHz
Figure 3. Active-Mode Current vs DCO Frequency
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
19
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
Low-Power-Mode Supply Currents (Into DVCC + AVCC) Excluding External Current – Electrical
Characteristics (1) (2)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
ILPM0, 1MHz
ILPM0, 100kHz
ILPM2
TEST CONDITIONS
Low-power mode 0
(LPM0) current (3)
fMCLK = 0 MHz,
fSMCLK = fDCO = 1 MHz,
fACLK = 32,768 Hz,
BCSCTL1 = CALBC1_1 MHZ,
DCOCTL = CALDCO_1 MHZ,
CPUOFF = 1, SCG0 = 0, SCG1 = 0,
OSCOFF = 0
Low-power mode 0
(LPM0) current (3)
fMCLK = 0 MHz,
fSMCLK = fDCO(0, 0) Ⅹ 100 kHz,
fACLK = 0 Hz,
RSELx = 0, DCOx = 0,
CPUOFF = 1, SCG0 = 0, SCG1 = 0,
OSCOFF = 1
Low-power mode 2
(LPM2) current (4)
fMCLK = fSMCLK = 0 MHz, fDCO = 1 MHz,
fACLK = 32,768 Hz,
BCSCTL1 = CALBC1_1 MHZ,
DCOCTL = CALDCO_1 MHZ,
CPUOFF = 1, SCG0 = 0, SCG1 = 1,
OSCOFF = 0
TA
–55°C to 125°C
–55°C to 125°C
–55°C to 85°C
125°C
VCC
75
90
3V
90
120
2.2 V
37
48
3V
41
65
22
29
2.2 V
25
ILPM3,LFXT1
Low-power mode 3
(LPM3) current (4)
0.7
1.4
2.8
4.5
125°C
6
18
–55°C
0.9
1.5
0.9
1.5
3.0
5.0
85°C
25°C
Low-power mode 3
current, (LPM3) (4)
6.5
19
–55°C
0.4
1.0
0.5
1.0
2.2
4.2
125°C
5.7
16.5
–55°C
0.5
1.2
0.6
1.2
2.5
4.5
85°C
25°C
85°C
ILPM4
(1)
(2)
(3)
(4)
(5)
20
Low-power mode 4
(LPM4) current (5)
fDCO = fMCLK = fSMCLK = 0 MHz,
fACLK = 0 Hz,
CPUOFF = 1, SCG0 = 1, SCG1 = 1,
OSCOFF = 1
3V
125°C
25°C
ILPM3,VLO
2.2 V
2.2 V
3V
125°C
6.0
17
–55°C
0.1
0.5
0.1
0.5
1.9
4.0
5.5
16
25°C
85°C
125°C
2.2 V/
3V
mA
mA
mA
45
1.4
85°C
fDCO = fMCLK = fSMCLK = 0 MHz,
fACLK from internal LF oscillator (VLO),
CPUOFF = 1, SCG0 = 1, SCG1 = 1,
OSCOFF = 0
32
0.7
25°C
UNIT
40
3V
–55°C
fDCO = fMCLK = fSMCLK = 0 MHz,
fACLK = 32,768 Hz,
CPUOFF = 1, SCG0 = 1, SCG1 = 1,
OSCOFF = 0
TYP MAX
2.2 V
–55°C to 85°C
125°C
MIN
mA
mA
mA
All inputs are tied to 0 V or VCC. Outputs do not source or sink any current.
For TA < 105°C, the currents are characterized with a Micro Crystal CC4V-T1A SMD crystal with a load capacitance of 9 pF.
The internal and external load capacitance is chosen to closely match the required 9 pF. For TA > 105°C, ACLK was sourced from an
external clock source.
Current for brownout and WDT clocked by SMCLK included.
Current for brownout and WDT clocked by ACLK included.
Current for brownout included.
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
Schmitt-Trigger Inputs (Ports P1, P2, P3, P4, and RST/NMI (1)) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
VIT+
Positive-going input threshold voltage
–55°C to 125°C
VIT–
Negative-going input threshold voltage
–55°C to 125°C
Vhys
Input voltage hysteresis (VIT+ – VIT–)
–55°C to 125°C
RPull
Pullup/pulldown resistor
For pullup: VIN = VSS;
For pulldown:
VIN = VCC
CI
Input capacitance
VIN = VSS or VCC
(1)
VCC
MIN
TYP MAX
2.2 V
1.00
1.65
3V
1.35
2.25
2.2 V
.55
1.20
3V
.75
1.65
2.2 V
0.2
1.0
3V
0.3
1.0
–55°C to 125°C
20
35
50
5
UNIT
V
V
V
kΩ
pF
RST/NMI limit values specified for -55°C to 125°C.
Inputs (Ports P1 and P2) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
t(int)
(1)
External interrupt timing
TEST CONDITIONS
TA
VCC
Port P1, P2: P1.x to P2.x, External
trigger pulse width to set interrupt flag (1)
–55°C to 125°C
2.2 V/3 V
MIN MAX
20
UNIT
ns
An external signal sets the interrupt flag every time the minimum interrupt pulse width t(int) is met. It may be set even with trigger signals
shorter than t(int).
Leakage Current (Ports P1, P2, P3 and P4) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
Ilkg(Px.x)
(1)
(2)
High-impedance leakage
current
TEST CONDITIONS
(1) (2)
TA
VCC
–55°C to 125°C
2.2 V/3 V
MIN MAX
±50
UNIT
nA
The leakage current is measured with VSS or VCC applied to the corresponding pin(s), unless otherwise noted.
The leakage of the digital port pins is measured individually. The port pin is selected for input and the pullup/pulldown resistor is
disabled.
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
21
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
Outputs (Ports P1, P2, P3, and P4) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
IOH(max) = –1.5 mA
High-level output
voltage
VOH
Low-level output
voltage
VOL
(1)
(2)
IOH(max) = –6 mA
(2)
VCC
–55°C to 125°C
IOH(max) = –1.5 mA (1)
–55°C to 125°C
IOH(max) = –6 mA (2)
–55°C to 125°C
IOL(max) = 1.5 mA (1)
–55°C to 125°C
IOL(max) = 6 mA (2)
–55°C to 125°C
IOL(max) = 1.5 mA
(1)
IOL(max) = 6 mA (2)
(1)
TA
–55°C to 125°C
–55°C to 125°C
–55°C to 125°C
2.2 V
3V
MIN
MAX
VCC – 0.25
VCC
VCC – 0.6
VCC
VCC – 0.25
VCC
VCC – 0.6
VCC
VSS
VSS+0.25
VSS
VSS+0.6
VSS
VSS+0.25
VSS
VSS+0.6
2.2 V
3V
UNIT
V
V
The maximum total current, IOH(max) and IOL(max), for all outputs combined, should not exceed ±12 mA to hold the maximum voltage drop
specified.
The maximum total current, IOH(max) and IOL(max), for all outputs combined, should not exceed ±48 mA to hold the maximum voltage drop
specified.
Output Frequency (Ports P1, P2, P3, and P4) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
fPx.y
Port output frequency
(with load)
P1.4/SMCLK, CL = 20 pF, RL = 1 kΩ against
VCC/2 (1) (2)
–55°C to 125°C
fPort_CLK
Clock output
frequency
P2.0/ACLK, P1.4/SMCLK, CL = 20 pF (2)
–55°C to 125°C
(1)
(2)
22
VCC
MIN
MAX
2.2 V
10
3V
12
2.2 V
12
3V
16
UNIT
MHz
MHz
A resistive divider with 2 times 0.5 kΩ between VCC and VSS is used as load. The output is connected to the center tap of the divider.
The output voltage reaches at least 10% and 90% VCC at the specified toggle frequency.
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
Typical Characteristics – Outputs
TYPICAL LOW-LEVEL OUTPUT CURRENT
vs
LOW-LEVEL OUTPUT VOLTAGE
TYPICAL LOW-LEVEL OUTPUT CURRENT
vs
LOW-LEVEL OUTPUT VOLTAGE
50.0
VCC = 2.2 V
P4.5
TA = 25°C
20.0
I OL − Typical Low-Level Output Current − mA
I OL − Typical Low-Level Output Current − mA
25.0
TA = 85°C
15.0
10.0
5.0
0.0
0.0
0.5
1.0
1.5
2.0
VCC = 3 V
P4.5
TA = 85°C
30.0
20.0
10.0
0.0
0.0
2.5
TA = 25°C
40.0
0.5
VOL − Low-Level Output Voltage − V
1.0
Figure 4.
3.0
3.5
0.0
VCC = 2.2 V
P4.5
I OH − Typical High-Level Output Current − mA
I OH − Typical High-Level Output Current − mA
2.5
TYPICAL HIGH-LEVEL OUTPUT CURRENT
vs
HIGH-LEVEL OUTPUT VOLTAGE
0.0
−5.0
−10.0
−15.0
−25.0
0.0
2.0
Figure 5.
TYPICAL HIGH-LEVEL OUTPUT CURRENT
vs
HIGH-LEVEL OUTPUT VOLTAGE
−20.0
1.5
VOL − Low-Level Output Voltage − V
TA = 85°C
TA = 25°C
0.5
1.0
1.5
2.0
2.5
VCC = 3 V
P4.5
−10.0
−20.0
−30.0
TA = 85°C
−40.0
−50.0
0.0
TA = 25°C
0.5
VOH − High-Level Output Voltage − V
Figure 6.
1.0
1.5
2.0
2.5
3.0
3.5
VOH − High-Level Output Voltage − V
Figure 7.
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
23
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
POR/Brownout Reset (BOR) – Electrical Characteristics (1)
(2)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
TEST
CONDITIONS
PARAMETER
TA
See Figure 8
dVCC/dt ≤ 3 V/s
V(B_IT–)
See Figure 8 through Figure 10
dVCC/dt ≤ 3 V/s
–55°C to 125°C
Vhys(B_IT–)
See Figure 8
dVCC/dt ≤ 3 V/s
–55°C to 125°C
td(BOR)
See Figure 8
–55°C to 125°C
t(reset)
Pulse length needed at RST/NMI
pin to accepted reset internally
–55°C to 125°C
(2)
MIN
TYP MAX
0.7 ×
V(B_IT–)
VCC(start)
(1)
VCC
70
2.2 V/3 V
2
130
UNIT
V
1.71
V
210
mV
2000
ms
ms
The current consumption of the brownout module is already included in the ICC current consumption data. The voltage level V(B_IT–) +
Vhys(B_IT– ) is ≤ 1.8 V.
During power up, the CPU begins code execution following a period of td(BOR) after VCC = V(B_IT–) + Vhys(B_IT–). The default DCO settings
must not be changed until VCC ≥ VCC(min), where VCC(min) is the minimum supply voltage for the desired operating frequency.
VCC
Vhys(B_IT−)
V(B_IT−)
VCC(start)
1
0
t d(BOR)
Figure 8. POR/Brownout Reset (BOR) vs Supply Voltage
24
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
Typical Characteristics - POR/Brownout Reset (BOR)
VCC
3V
2
VCC(drop) − V
VCC = 3 V
Typical Conditions
t pw
1.5
1
VCC(drop)
0.5
0
0.001
1
1000
1 ns
tpw − Pulse Width − µs
1 ns
tpw − Pulse Width − µs
Figure 9. VCC(drop) Level With a Square Voltage Drop to Generate a POR/Brownout Signal
VCC
2
t pw
3V
VCC(drop) − V
VCC = 3 V
1.5
Typical Conditions
1
VCC(drop)
0.5
0
0.001
tf = tr
1
1000
tpw − Pulse Width − µs
tf
tr
tpw − Pulse Width − µs
Figure 10. VCC(drop) Level With a Triangle Voltage Drop to Generate a POR/Brownout Signal
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
25
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
Main DCO Characteristics
•
•
•
All ranges selected by RSELx overlap with RSELx + 1: RSELx = 0 overlaps RSELx = 1, ... RSELx = 14
overlaps RSELx = 15.
DCO control bits DCOx have a step size as defined by parameter SDCO.
Modulation control bits MODx select how often fDCO(RSEL,DCO+1) is used within the period of 32 DCOCLK
cycles. The frequency fDCO(RSEL,DCO) is used for the remaining cycles. The frequency is an average equal to:
32 f DCO(RSEL,DCO) f DCO(RSEL,DCO ) 1)
f average +
MOD f DCO(RSEL,DCO) ) (32 * MOD) f DCO(RSEL,DCO ) 1)
DCO Frequency – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
VCC
Supply voltage range
MIN
TYP MAX
RSELx < 14
TEST CONDITIONS
–55°C to 125°C
TA
VCC
1.8
3.6
RSELx = 14
–55°C to 125°C
2.2
3.6
RSELx = 15
–55°C to 125°C
3.0
3.6
UNIT
V
fDCO(0,0)
DCO frequency (0, 0)
RSELx = 0, DCOx = 0,
MODx = 0
–55°C to 125°C
2.2 V/3 V
0.06
0.14
MHz
fDCO(0,3)
DCO frequency (0, 3)
RSELx = 0, DCOx = 3,
MODx = 0
–55°C to 125°C
2.2 V/3 V
0.07
0.17
MHz
fDCO(1,3)
DCO frequency (1, 3)
RSELx = 1, DCOx = 3,
MODx = 0
–55°C to 125°C
2.2 V/3 V
0.10
0.20
MHz
fDCO(2,3)
DCO frequency (2, 3)
RSELx = 2, DCOx = 3,
MODx = 0
–55°C to 125°C
2.2 V/3 V
0.14
0.28
MHz
fDCO(3,3)
DCO frequency (3, 3)
RSELx = 3, DCOx = 3,
MODx = 0
–55°C to 125°C
2.2 V/3 V
0.20
0.40
MHz
fDCO(4,3)
DCO frequency (4, 3)
RSELx = 4, DCOx = 3,
MODx = 0
–55°C to 125°C
2.2 V/3 V
0.28
0.54
MHz
fDCO(5,3)
DCO frequency (5, 3)
RSELx = 5, DCOx = 3,
MODx = 0
–55°C to 125°C
2.2 V/3 V
0.39
0.77
MHz
fDCO(6,3)
DCO frequency (6, 3)
RSELx = 6, DCOx = 3,
MODx = 0
–55°C to 125°C
2.2 V/3 V
0.54
1.06
MHz
fDCO(7,3)
DCO frequency (7, 3)
RSELx = 7, DCOx = 3,
MODx = 0
–55°C to 125°C
2.2 V/3 V
0.80
1.50
MHz
fDCO(8,3)
DCO frequency (8, 3)
RSELx = 8, DCOx = 3,
MODx = 0
–55°C to 125°C
2.2 V/3 V
1.10
2.10
MHz
fDCO(9,3)
DCO frequency (9, 3)
RSELx = 9, DCOx = 3,
MODx = 0
–55°C to 125°C
2.2 V/3 V
1.60
3.00
MHz
fDCO(10,3)
DCO frequency (10, 3)
RSELx = 10, DCOx = 3,
MODx = 0
–55°C to 125°C
2.2 V/3 V
2.50
4.30
MHz
fDCO(11,3)
DCO frequency (11, 3)
RSELx = 11, DCOx = 3,
MODx = 0
–55°C to 125°C
2.2 V/3 V
3.00
5.50
MHz
fDCO(12,3)
DCO frequency (12, 3)
RSELx = 12, DCOx = 3,
MODx = 0
–55°C to 125°C
2.2 V/3 V
4.30
7.30
M Hz
fDCO(13,3)
DCO frequency (13, 3)
RSELx = 13, DCOx = 3,
MODx = 0
–55°C to 125°C
2.2 V/3 V
6.00
9.60
MHz
fDCO(14,3)
DCO frequency (14, 3)
RSELx = 14, DCOx = 3,
MODx = 0
–55°C to 125°C
2.2 V/3 V
8.60
13.9
MHz
fDCO(15,3)
DCO frequency (15, 3)
RSELx = 15, DCOx = 3,
MODx = 0
–55°C to 125°C
3V
12.0
18.5
MHz
fDCO(15,7)
DCO frequency (15, 7)
RSELx = 15, DCOx = 7,
MODx = 0
–55°C to 125°C
3V
16.0
26.0
MHz
SRSEL
Frequency step
between range RSEL
and RSEL+1
SRSEL =
fDCO(RSEL+1,DCO)/fDCO(RSEL,DCO)
–55°C to 125°C
2.2 V/3 V
1.55
ratio
26
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
DCO Frequency – Electrical Characteristics (continued)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
SDCO
Duty cycle
Frequency step
between tap DCO and
DCO+1
TEST CONDITIONS
TA
VCC
MIN
TYP MAX
UNIT
SDCO =
fDCO(RSEL,DCO+1)/fDCO(RSEL,DCO)
–55°C to 125°C
2.2 V/3 V
1.05
1.08
1.12
ratio
Measured at P1.4/SMCLK
–55°C to 125°C
2.2 V/3 V
40
50
60
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
%
27
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
Calibrated DCO Frequencies (Tolerance at Calibration) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
Frequency tolerance at calibration
TA
VCC
MIN
TYP
MAX
25°C
3V
–1
±0.2
1
UNIT
25°C
3V
0.990
1
1.010
MHz
%
fCAL(1 MHz)
1-MHz calibration value
BCSCTL1 = CALBC1_1MHZ,
DCOCTL = CALDCO_1MHZ,
Gating time: 5 ms
fCAL(8 MHz)
8-MHz calibration value
BCSCTL1 = CALBC1_8MHZ,
DCOCTL = CALDCO_8MHZ,
Gating time: 5 ms
25°C
3V
7.920
8
8.080
MHz
fCAL(12 MHz)
12-MHz calibration value
BCSCTL1 = CALBC1_12MHZ,
DCOCTL = CALDCO_12MHZ,
Gating time: 5 ms
25°C
3V
11.88
12
12.12
MHz
fCAL(16 MHz)
16-MHz calibration value
BCSCTL1 = CALBC1_16MHZ,
DCOCTL = CALDCO_16MHZ,
Gating time: 2 ms
25°C
3V
15.84
16
16.16
MHz
Calibrated DCO Frequencies (Tolerance Over Temperature) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
TA
VCC
MIN
TYP
MAX
1-MHz tolerance over temperature
PARAMETER
–55°C to 125°C
3V
–2.5
±0.5
2.5
%
8-MHz tolerance over temperature
–55°C to 125°C
3V
–2.5
±1.0
2.5
%
12-MHz tolerance over temperature
–55°C to 125°C
3V
–2.5
±1.0
2.5
%
16-MHz tolerance over temperature
–55°C to 125°C
3V
–3.0
±2.0
3.0
%
2.2 V
0.970
1
1.030
3V
0.975
1
1.025
3.6 V
0.970
1
1.030
2.2 V
7.760
8
8.400
3V
7.800
8
8.200
3.6 V
7.600
8
8.240
2.2 V
11.70
12
12.30
3V
11.70
12
12.30
3.6 V
11.70
12
12.30
3V
15.52
16
16.48
3.6 V
15.00
16
16.48
fCAL(1MHz)
fCAL(8MHz)
fCAL(12MHz)
fCAL(16MHz)
28
1-MHz calibration value
8-MHz calibration value
TEST CONDITIONS
BCSCTL1 = CALBC1_1MHz,
DCOCTL = CALDCO_1MHZ,
Gating time: 5 ms
BCSCTL1 = CALBC1_8MHZ,
DCOCTL = CALDCO_8MHZ,
Gating time: 5 ms
12-MHz calibration value
BCSCTL1 = CALBC1_12MHZ,
DCOCTL = CALDCO_12MHZ,
Gating time: 5 ms
16-MHz calibration value
BCSCTL1 = CALBC1_16MHZ,
DCOCTL = CALDCO_16MHZ,
Gating time: 2 ms
Submit Documentation Feedback
–55°C to 125°C
–55°C to 125°C
–55°C to 125°C
–55°C to 125°C
UNIT
MHz
MHz
MHz
MHz
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
Calibrated DCO Frequencies (Tolerance Over Supply Voltage VCC) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
TA
VCC
MIN
TYP
MAX
1-MHz tolerance over VCC
PARAMETER
TEST CONDITIONS
25°C
1.8 V to 3.6 V
–3
±2
3
%
8-MHz tolerance overVCC
25°C
1.8 V to 3.6 V
–3
±2
3
%
12-MHz tolerance over VCC
25°C
2.2 V to 3.6 V
–3
±2
3
%
–6
±2
3
%
16-MHz tolerance over VCC
UNIT
25°C
3 V to 3.6 V
25°C
1.8 V to 3.6 V
0.970
1
1.030
MHz
fCAL(1MHz)
1-MHz
calibration value
BCSCTL1 = CALBC1_1MHZ,
DCOCTL = CALDCO_1MHZ,
Gating time: 5 ms
fCAL(8MHz)
8-MHz
calibration value
BCSCTL1 = CALBC1_8MHZ,
DCOCTL = CALDCO_8MHZ,
Gating time: 5 ms
25°C
1.8 V to 3.6 V
7.760
8
8.240
MHz
fCAL(12MHz)
12-MHz
calibration value
BCSCTL1 = CALBC1_12MHZ,
DCOCTL = CALDCO_12MHZ,
Gating time: 5 ms
25°C
2.2 V to 3.6 V
11.64
12
12.36
MHz
fCAL(16MHz)
16-MHz
calibration value
BCSCTL1 = CALBC1_16MHZ,
DCOCTL = CALDCO_16MHZ,
Gating time: 2 ms
25°C
3 V to 3.6 V
15.00
16
16.48
MHz
Calibrated DCO Frequencies (Overall Tolerance) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
TA
VCC
1-MHz tolerance
over temperature
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
–55°C to 125°C
8-MHz tolerance
over temperature
UNIT
1.8 V to 3.6 V
-5
±2
+5
%
–55°C to 125°C
1.8 V to 3.6 V
-5
±2
+5
%
12-MHz tolerance
over temperature
–55°C to 125°C
2.2 V to 3.6 V
-5
±2
+5
%
16-MHz tolerance
over temperature
–55°C to 125°C
3 V to 3.6 V
-6
±3
+6
%
fCAL(1MHz)
1-MHz
calibration value
BCSCTL1 = CALBC1_1MHZ,
DCOCTL = CALDCO_1MHZ,
Gating time: 5 ms
–55°C to 125°C
1.8 V to 3.6 V
.950
1
1.050
MHz
fCAL(8MHz)
8-MHz
calibration value
BCSCTL1 = CALBC1_8MHZ,
DCOCTL = CALDCO_8MHZ,
Gating time: 5 ms
–55°C to 125°C
1.8 V to 3.6 V
7.6
8
8.4
MHz
fCAL(12MHz)
12-MHz
calibration value
BCSCTL1 = CALBC1_12MHZ,
DCOCTL = CALDCO_12MHZ,
Gating time: 5 ms
–55°C to 125°C
2.2 V to 3.6 V
11.4
12
12.6
MHz
fCAL(16MHz)
16-MHz
calibration value
BCSCTL1 = CALBC1_16MHZ,
DCOCTL = CALDCO_16MHZ,
Gating time: 2 ms
–55°C to 125°C
3 V to 3.6 V
15.00
16
17.00
MHz
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
29
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
Typical Characteristics – Calibrated 1-MHz DCO Frequency
1.03
1.03
1.02
1.02
Frequency − MHz
1.00
VCC = 2.2 V
VCC = 3.0 V
0.99
Frequency - MHz
VCC = 1.8 V
1.01
TA = 125 °C
1.01
TA = 85 °C
1.00
TA = 25 °C
0.99
TA = -40 °C
VCC = 3.6 V
0.98
0.98
0.97
−50.0
−25.0
0.0
25.0
50.0
75.0
100.0
0.97
1.5
2.0
TA − Temperature − °C
Figure 11. Calibrated 1-MHz Frequency vs
Temperature
2.5
3.0
3.5
4.0
VCC - Suppl y Voltage - V
Figure 12. Calibrated 1-MHz Frequency vs VCC
Wake-Up From Lower-Power Modes (LPM3/4) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
tDCO,LPM3/4
tCPU,LPM3/4
DCO clock wake-up time
from LPM3/4 (1)
TA
VCC
BCSCTL1 =
CALBC1_1MHZ,
DCOCTL =
CALDCO_1MHZ,
TEST CONDITIONS
MIN
TYP
MAX
–55°C to 125°C
2.2 V/3 V
2
BCSCTL1 =
CALBC1_8MHZ,
DCOCTL =
CALDCO_8MHZ,
–55°C to 125°C
2.2 V/3 V
1.5
BCSCTL1 =
CALBC1_12MHZ,
DCOCTL =
CALDCO_12MHZ,
–55°C to 125°C
3V
1
BCSCTL1 =
CALBC1_16MHZ,
DCOCTL =
CALDCO_16MHZ,
–55°C to 125°C
3V
1
UNIT
ms
1/fMCL
K+
tClock,L
CPU wake-up time from
LPM3/4 (2)
PM3/4
(1)
(2)
30
The DCO clock wake-up time is measured from the edge of an external wake-up signal (e.g., port interrupt) to the first clock edge
observable externally on a clock pin (MCLK or SMCLK).
Parameter applicable only if DCOCLK is used for MCLK.
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
Typical Characteristics – DCO Clock Wake-Up Time From LPM3/4
DCO Wake Time − us
10.00
RSELx = 0...11
RSELx = 12...15
1.00
0.10
0.10
1.00
10.00
DCO Frequency − MHz
Figure 13. Clock Wake-Up Time From LPM3 vs DCO Frequency
DCO With External Resistor ROSC – Electrical Characteristics (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
TYP
1.8
UNIT
fDCO,ROSC
DCO output frequency with ROSC
DCOR = 1, RSELx = 4, DCOx = 3, MODx = 0,
TA = 25°C
2.2 V
3V
1.95
Dt
Temperature drift
DCOR = 1, RSELx = 4, DCOx = 3, MODx = 0
2.2 V/3 V
±0.1
%/°C
DV
Drift with VCC
DCOR = 1, RSELx = 4, DCOx = 3, MODx = 0
2.2 V/3 V
10
%/V
(1)
MHz
ROSC = 100kΩ. Metal film resistor, type 0257. 0.6 watt with 1% tolerance and TK = ±50ppm/°C
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
31
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
Typical Characteristics - DCO With External Resistor ROSC
10.00
DCO Frequency − MHz
DCO Frequency − MHz
10.00
1.00
0.10
RSELx = 4
0.01
10.00
100.00
1000.00
1.00
0.10
RSELx = 4
0.01
10.00
10000.00
100.00
ROSC − External Resistor − kW
Figure 14. DCO Frequency vs ROSC,
VCC = 2.2 V, TA = 25°C
2.50
2.25
ROSC = 100k
2.00
DCO Frequency − MHz
1.75
1.50
1.25
1.00
ROSC = 270k
0.75
0.50
DCO Frequency − MHz
2.25
ROSC = 100k
2.00
1.75
1.50
1.25
1.00
ROSC = 270k
0.75
0.50
ROSC = 1M
0.25
−25.0
0.0
25.0
50.0
75.0
ROSC = 1M
0.25
100.0
0.00
2.0
2.5
TA − Temperature − 5C
Figure 16. DCO Frequency vs Temperature, VCC =
3.0 V
32
10000.00
Figure 15. DCO Frequency vs ROSC,
VCC = 3.0 V, TA = 25°C
2.50
0.00
−50.0
1000.00
ROSC − External Resistor − kW
Submit Documentation Feedback
3.0
3.5
4.0
VCC − Supply Voltage − V
Figure 17. DCO Frequency vs VCC, TA = 25°C
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
Crystal Oscillator (LFXT1) Low-Frequency Modes – Electrical Characteristics (1)
(2)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
fLFXT1,LF
LFXT1 oscillator crystal
frequency, LF mode 0, 1
LFXT1 oscillator
fLFXT1,LF logic-level square-wave
input frequency, LF
,logic
mode
OALF
Oscillation allowance for
LF crystals
TEST CONDITIONS
TA
VCC
XTS = 0, LFXT1Sx = 0 or 1
–40°C to
105°C
1.8 V to 3.6 V
XTS = 0, LFXT1Sx = 3
–55°C to
125°C
1.8 V to 3.6 V
XTS = 0, LFXT1Sx = 0;
fLFXT1,LF = 32,768 kHz,
CL,eff = 6 pF
–40°C to
105°C
500
XTS = 0, LFXT1Sx = 0;
fLFXT1,LF = 32,768 kHz,
CL,eff = 12 pF
–40°C to
105°C
200
TYP
10,000
1
Duty
Cycle
LF mode
XTS = 0, Measured at
P1.4/ACLK,
fLFXT1,LF = 32,768 Hz
fFault,LF
Oscillator fault frequency
XTS = 0, LFXT1Sx = 3 (5)
threshold, LF mode (4)
–40°C to
105°C
(2)
(3)
(4)
(5)
Hz
pF
8.5
XCAPx = 3
(1)
50,000
kΩ
5.5
XCAPx = 2
UNIT
Hz
32,768
XCAPx = 1
XTS = 0
MAX
32,768
XCAPx = 0
Integrated effective load
capacitance,
LF mode (3)
CL,eff
MIN
11
–55°C to
125°C
2.2 V/3 V
30
–55°C to
125°C
2.2 V/3 V
10
50
70
%
10,000
Hz
To improve EMI on the LFXT1 oscillator the following guidelines should be observed:
(a) Keep as short of a trace as possible between the device and the crystal.
(b) Design a good ground plane around the oscillator pins.
(c) Prevent crosstalk from other clock or data lines into oscillator pins XIN and XOUT.
(d) Avoid running PCB traces underneath or adjacent to the XIN and XOUT pins.
(e) Use assembly materials and praxis to avoid any parasitic load on the oscillator XIN and XOUT pins.
(f) If conformal coating is used, ensure that it does not induce capacitive/resistive leakage between the oscillator pins.
(g) Do not route the XOUT line to the JTAG header to support the serial programming adapter as shown in other documentation. This
signal is no longer required for the serial programming adapter.
Use of the LFXT1 Crystal Oscillator with TA > 105°C is not guaranteed. It is recommended that an external digital clock source or the
internal DCO is used to provide clocking.
Includes parasitic bond and package capacitance (approximately 2 pF per pin). Since the PCB adds additional capacitance it is
recommended to verify the correct load by measuring the ACLK frequency. For a correct setup the effective load capacitance should
always match the specification of the used crystal.
Frequencies below the MIN specification set the fault flag, frequencies above the MAX specification do not set the fault flag.
Frequencies in between might set the flag.
Measured with logic-level input frequency, but also applies to operation with crystals with TA < 105°C.
Internal Very-Low-Power, Low-Frequency Oscillator (VLO) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
TEST
CONDITIONS
PARAMETER
fVLO
VLO frequency
dfVLO/dT
VLO frequency temperature drift
dfVLO/dVCC VLO frequency supply voltage drift
(1)
(2)
TA
VCC
–55°C to 85°C
2.2 V/3 V
125°C
2.2 V/3 V
(1)
–55°C to 125°C
2.2 V/3 V
(2)
25°C
1.8 V –
3.6V
MIN
4
TYP MAX
12
20
22
UNIT
kHz
0.5
%/°C
4
%/V
Calculated using the box method:
I Version: [MAX(–55...85°C) – MIN(–55...85°C)]/MIN(55–...85°C)/[85°C – (–55°C)]
T Version: [MAX(–55...125°C) – MIN(–55...125°C)]/MIN(–55...125°C)/[125°C – (–55°C)]
Calculated using the box method: [MAX(1.8...3.6 V) – MIN(1.8...3.6 V)]/MIN(1.8...3.6 V)/(3.6 V – 1.8 V)
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
33
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
Crystal Oscillator (LFXT1) High Frequency Modes – Electrical Characteristics (1)
(2)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
fLFXT1,H
F0
fLFXT1,H
F1
fLFXT1,H
F2
TA
VCC
MIN
TYP MAX UNIT
XTS = 1, LFXT1Sx = 0
–40°C to 105°C
1.8 V to 3.6 V
0.4
1 MHz
LFXT1 oscillator lcrystal frequency,
XTS = 1, LFXT1Sx = 1
HF mode 1
–40°C to 105°C
1.8 V to 3.6 V
1
4 MHz
1.8 V to 3.6 V
2
10
LFXT1 oscillator crystal frequency,
HF mode 2
–40°C to 105°C
2.2 V to 3.6 V
2
12 MHz
LFXT1 oscillator crystal frequency,
HF mode 0
TEST CONDITIONS
XTS = 1, LFXT1Sx = 2
3 V to 3.6 V
fLFXT1,H
F,logic
LFXT1 oscillator logic-level
square-wave input frequency,
HF mode
XTS = 1, LFXT1Sx = 3
–40°C to 105°C
2
16
1.8 V to 3.6 V
0.4
10
2.2 V to 3.6 V
0.4
12 MHz
3 V to 3.6 V
0.4
16
XTS = 0, LFXT1Sx = 0;
fLFXT1,HF = 1 MHz,
CL,eff = 15 pF
OAHF
Oscillation allowance for HF
crystals
(see Figure 18 and Figure 19)
XTS = 0, LFXT1Sx = 1
fLFXT1,HF = 4 MHz,
CL,eff = 15 pF
2700
–40°C to 105°C
XTS = 0, LFXT1Sx = 2
fLFXT1,HF = 16 MHz,
CL,eff = 15 pF
CL,eff
Duty
Cycle
fFault,HF
(1)
(2)
(3)
(4)
(5)
(6)
34
Integrated effective load
capacitance,
HF mode (3)
HF mode
Oscillator fault frequency, HF mode
(5)
Ω
800
300
XTS = 1 (4)
–40°C to 105°C
XTS = 1, Measured at
P1.4/ACLK,
fLFXT1,HF = 10 MHz
–55°C to 125°C
XTS = 1, Measured at
P1.4/ACLK,
fLFXT1,HF = 16 MHz
–55°C to 125°C
XTS = 1, LFXT1Sx = 3 (6)
–55°C to 125°C
1
40
50
pF
60
2.2 V/3 V
%
40
2.2 V/3 V
30
50
60
300
kHz
To improve EMI on the LFXT1 oscillator the following guidelines should be observed:
(a) Keep as short of a trace as possible between the device and the crystal.
(b) Design a good ground plane around the oscillator pins.
(c) Prevent crosstalk from other clock or data lines into oscillator pins XIN and XOUT.
(d) Avoid running PCB traces underneath or adjacent to the XIN and XOUT pins.
(e) Use assembly materials and praxis to avoid any parasitic load on the oscillator XIN and XOUT pins.
(f) If conformal coating is used, ensure that it does not induce capacitive/resistive leakage between the oscillator pins.
(g) Do not route the XOUT line to the JTAG header to support the serial programming adapter as shown in other documentation. This
signal is no longer required for the serial programming adapter.
Use of the LFXT1 Crystal Oscillator with TA > 105°C is not guaranteed. It is recommended that an external digital clock source or the
internal DCO is used to provide clocking.
Includes parasitic bond and package capacitance (approximately 2 pF per pin). Since the PCB adds additional capacitance it is
recommended to verify the correct load by measuring the ACLK frequency. For a correct setup the effective load capacitance should
always match the specification of the used crystal.
Requires external capacitors at both terminals. Values are specified by crystal manufacturers.
Frequencies below the MIN specification set the fault flag, frequencies above the MAX specification do not set the fault flag.
Frequencies in between might set the flag.
Measured with logic-level input frequency, but also applies to operation with crystals
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
Typical Characteristics – LFXT1 Oscillator in HF Mode (XTS = 1)
800.0
100000.00
Oscillation Allowance – W
10000.00
1000.00
LFXT1Sx = 3
100.00
LFXT1Sx = 1
LFXT1Sx = 2
XT Oscillator Supply Current − uA
LFXT1Sx = 3
700.0
600.0
500.0
400.0
300.0
LFXT1Sx = 2
200.0
100.0
LFXT1Sx = 1
10.00
0.10
1.00
10.00
0.0
0.0
100.00
Crystal Frequency − MHz
4.0
8.0
12.0
16.0
20.0
Crystal Frequency − MHz
Figure 18. Oscillation Allowance vs Crystal
Frequency, CL,eff = 15 pF, TA = 25°C
Figure 19. XT Oscillator Supply Current vs Crystal
Frequency, CL,eff = 15 pF, TA = 25°C
Timer_A – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
fTA
Timer_A clock frequency
Internal: SMCLK, ACLK,
External: TACLK, INCLK,
Duty cycle = 50% ± 10%
tTA,cap
Timer_A, capture timing
TA0, TA1, TA2
TA
VCC
–55°C to 125°C
–55°C to 125°C
MIN
MAX
2.2 V
10
3V
16
2.2 V/3 V
20
UNIT
MHz
ns
Timer_B – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
VCC
fTB
Timer_B clock frequency
Internal: SMCLK, ACLK,
External: TBCLK,
Duty Cycle = 50% ± 10%
–55°C to 125°C
tTB,cap
Timer_B, capture timing
TB0, TB1, TB2
–55°C to 125°C
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MIN
MAX
2.2 V
10
3V
16
2.2 V/3 V
20
Submit Documentation Feedback
UNIT
MHz
ns
35
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
USCI (UART Mode) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
Internal: SMCLK, ACLK,
External: UCLK;
Duty cycle = 50% ± 10%
TA
VCC
fUSCI
USCI input clock frequency
fBITCLK
BITCLK clock frequency
(equals baud rate in MBaud)
–55°C to 125°C
tt
UART receive deglitch time (1)
–55°C to 125°C
(1)
MIN
TYP
–55°C to 125°C
MAX
UNIT
fSYSTE
MHz
M
2.2 V/3 V
1
2.2 V
50
150
600
3V
50
150
600
MHz
ns
Pulses on the UART receive input (UCxRX) shorter than the UART receive deglitch time are suppressed. To ensure that pulses are
correctly recognized, their width should exceed the maximum specification of the deglitch time.
USCI (SPI Master Mode) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 20 and
Figure 21)
PARAMETER
TEST CONDITIONS
SMCLK, ACLK,
Duty cycle = 50% ± 10%
TA
fUSCI
USCI input clock frequency
tSU,MI
SOMI input data setup time
–55°C to 125°C
tHD,MI
SOMI input data hold time
–55°C to 125°C
tVALID,MO
SIMO output data valid time
UCLK edge to SIMO valid,
CL = 20 pF
VCC
MIN
–55°C to 125°C
–55°C to 125°C
2.2 V
110
3V
75
2.2 V
0
3V
0
MAX
UNIT
fSYSTEM
MHz
ns
ns
2.2 V
30
3V
20
ns
USCI (SPI Slave Mode) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 22 and
Figure 23)
PARAMETER
TEST CONDITIONS
TA
VCC
MIN
TYP MAX
UNIT
tSTE,LEAD
STE lead time,
STE low to clock
tSTE,LAG
STE lag time,
Last clock to STE high
tSTE,ACC
STE access time,
STE low to SOMI data out
2.2 V/3 V
50
ns
tSTE,DIS
STE disable time,
STE high to SOMI high
impedance
2.2 V/3 V
50
ns
tSU,SI
SIMO input data setup time
–55°C to 125°C
tHD,SI
SIMO input data hold time
–55°C to 125°C
tVALID,SO
SOMI output data valid time
36
Submit Documentation Feedback
2.2 V/3 V
–55°C to 125°C
UCLK edge to SOMI valid,
CL = 20 pF
–55°C to 125°C
2.2 V/3 V
50
ns
10
2.2 V
20
3V
15
2.2 V
10
3V
10
ns
ns
ns
2.2 V
75
110
3V
50
75
ns
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
1/fUCxCLK
CKPL
=0
CKPL
=1
UCLK
tLOW/HIGH tLOW/HIGH
tSU,MI
tHD,MI
SCMI
tVALID, MO
SIMO
Figure 20. SPI Master Mode, CKPH = 0
1/fUCxCLK
CKPL
=0
CKPL
=1
UCLK
tLOW/HIGH tLOW/HIGH
tSU,MI
tHD,MI
SCMI
tVALID, MO
SIMO
Figure 21. SPI Master Mode, CKPH = 1
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
37
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
tSTE,LEAD
tSTE,LAG
STE
1/fUCxCLK
CKPL = 0
UCLK
CKPL = 1
tLOW,HIGH tLOW,HIGH
tSU,SIMO
tHD,SIMO
SIMO
tACC
tVALID,SOMI
tDIS
SOMI
Figure 22. SPI Slave Mode, CKPH = 0
tSTE,LEAD
tSTE,LAG
STE
1/fUCxCLK
CKPL = 0
UCLK
CKPL = 1
tLOW,HIGH tLOW,HIGH
tHD,SI
,
tSU,SI
SIMO
tACC
tVALID,SO
tDIS
SOMI
Figure 23. SPI Slave Mode, CKPH = 1
38
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
USCI (I2C Mode) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 24)
PARAMETER
TEST CONDITIONS
fUSCI
USCI input clock frequency
fSCL
SCL clock frequency
TA
VCC
MIN
Internal: SMCLK, ACLK,
External: UCLK,
Duty cycle = 50% ± 10%
TYP
MAX
fSYST
UNIT
MHz
EM
–55°C to 125°C
fSCL ≤ 100 kHz
–55°C to 125°C
fSCL > 100 kHz
–55°C to 125°C
fSCL ≤ 100 kHz
–55°C to 125°C
fSCL > 100 kHz
–55°C to 125°C
2.2 V/3 V
400
kHz
tHD,STA
Hold time (repeated) START
tSU,STA
Set-up time for a repeated
START
tHD,DAT
Data hold time
–55°C to 125°C
2.2 V/3 V
0
ns
tSU,DAT
Data set-up time
–55°C to 125°C
2.2 V/3 V
250
ns
tSU,STO
Set-up time for STOP
–55°C to 125°C
2.2 V/3 V
4.0
2.2 V
50
150
600
3V
50
100
600
tSP
Pulse width of spikes
suppressed by input filter
–55°C to 125°C
tHD ,STA
2.2 V/3 V
0
4.0
2.2 V/3 V
ms
0.6
4.7
ms
0.6
tSU ,STA tHD ,STA
ms
ns
tBUF
SDA
t
LOW
tHIGH
tSP
SCL
tSU ,DAT
tSU , STO
tHD ,DAT
Figure 24. I2C Mode Timing
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
39
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
10-Bit ADC, Power-Supply and Input Range Conditions – Electrical Characteristics (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
VCC
TEST CONDITIONS
Analog supply voltage range
VAx
Analog input voltage range
IADC10
IREF+
(2)
ADC10 supply current (3)
Reference supply current,
reference buffer disabled (4)
MIN
TYP MAX
VSS = 0 V
–55°C to125 °C
TA
VCC
2.2
3.6
V
All Ax terminals,
Analog inputs selected in
ADC10AE register
–55°C to 125°C
0
VCC
V
fADC10CLK = 5.0 MHz,
ADC10ON = 1, REFON = 0,
ADC10SHT0 = 1,
ADC10SHT1 = 0,
ADC10DIV = 0
2.2 V
0.52
1.05
–55°C to 125°C
3V
0.6
1.2
fADC10CLK = 5.0 MHz,
ADC10ON = 0, REF2_5V = 0,
REFON = 1, REFOUT = 0
–55°C to 125°C
fADC10CLK = 5.0 MHz,
ADC10ON = 0, REF2_5V = 1,
REFON = 1, REFOUT = 0
0.25
.4
–55°C to 125°C
3V
1.1
1.4
fADC10CLK = 5.0 MHz,
ADC10ON = 0, REFON = 1,
REF2_5V = 0,
REFOUT = 1, ADC10SR = 0
–55°C to 85°C
2.2 V/3 V
Reference buffer supply current
with ADC10SR = 0 (4)
125°C
2.2 V/3 V
2.2 V/3 V
Reference buffer supply current
with ADC10SR = 1 (4)
fADC10CLK = 5.0 MHz,
ADC10ON = 0, REFON = 1,
REF2_5V = 0, REFOUT = 1,
ADC10SR=1
–55°C to 85°C
IREFB,1
125°C
2.2 V/3 V
CI
Input capacitance
Only one terminal Ax selected at
a time
RI
Input MUX ON resistance
0 V ≤ VAx ≤ VCC
40
mA
2.2 V/3 V
IREFB,0
(1)
(2)
(3)
(4)
UNIT
2.2 V/3 V
1.8
0.5
mA
mA
.7
mA
.8
mA
27
pF
2000
Ω
The leakage current is defined in the leakage current table with Px.x/Ax parameter.
The analog input voltage range must be within the selected reference voltage range VR+ to VR– for valid conversion results.
The internal reference supply current is not included in current consumption parameter IADC10.
The internal reference current is supplied via terminal VCC. Consumption is independent of the ADC10ON control bit, unless a
conversion is active. The REFON bit enables the built-in reference to settle before starting an A/D conversion.
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
10-Bit ADC, Built-In Voltage Reference – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
VCC,REF+
Positive built-in
reference analog
supply voltage range
VREF+
Positive built-in
reference voltage
ILD,VREF+
Maximum VREF+ load
current
VREF+ load regulation
TEST CONDITIONS
TA
VCC
MIN
TYP MAX
IVREF+ ≤ 1 mA, REF2_5V = 0
–55°C to 125°C
2.2
IVREF+ ≤ 0.5 mA, REF2_5V = 1
–55°C to 125°C
2.8
IVREF+ ≤ 1 mA, REF2_5V = 1
–55°C to 125°C
2.9
IVREF+ ≤ IVREF+max, REF2_5V = 0
–55°C to 125°C
2.2 V/3 V
1.41
1.5
1.59
IVREF+ ≤ IVREF+max, REF2_5V = 1
–55°C to 125°C
3V
2.35
2.5
2.65
–55°C to 125°C
IVREF+ = 500 mA ± 100 mA,
Analog input voltage VAx Ⅹ 0.75 V,
REF2_5V = 0
–55°C to 125°C
IVREF+ = 500 mA ± 100 mA,
Analog input voltage VAx Ⅹ 1.25 V,
REF2_5V = 1
–55°C to 125°C
2.2 V
UNIT
V
±0.5
3V
±1
2.2 V/3 V
±2
V
mA
LSB
IVREF+ = 100 mA→900
mA,
VAx Ⅹ 0.5 × VREF+,
Error of conversion
result ≤ 1 LSB
CVREF+
Maximum capacitance
at pin VREF+ (1)
IVREF+ ≤ = 1 mA,
REFON = 1, REFOUT = 1
–55°C to 125°C
2.2 V/3 V
100
pF
TCREF+
Temperature
coefficient
IVREF+ = const. with
0 mA ≤ IVREF+ ≤ 1 mA
–55°C to 125°C
2.2 V/3 V
±100
ppm/°
C
tREFON
Settling time of internal IVREF+ = 0.5 mA, REF2_5V = 0
reference voltage (2)
REFON = 0 → 1
–55°C to 125°C
3.6 V
tREFBURST
(1)
(2)
–55°C to 125°C
ADC10SR = 1
–55°C to 125°C
±2
VREF+ load regulation
response time
Settling time of
reference buffer (2)
ADC10SR = 0
3V
IVREF+ = 0.5 mA,
REF2_5V = 0,
REFON = 1,
REFBURST = 1
ADC10SR = 0
–55°C to 125°C
ADC10SR = 1
–55°C to 125°C
IVREF+ = 0.5 mA,
REF2_5V = 1,
REFON = 1,
REFBURST = 1
ADC10SR = 0
–55°C to 125°C
ADC10SR = 1
–55°C to 125°C
400
3V
2000
30
ns
ms
1
2.2 V
2.5
2
3V
ms
4.5
The capacitance applied to the internal buffer operational amplifier, if switched to terminal P2.4/TA2/A4/VREF+/VeREF+ (REFOUT = 1),
must be limited; the reference buffer may become unstable otherwise.
The condition is that the error in a conversion started after tREFON or tRefBuf is less than ±0.5 LSB.
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
41
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
10-Bit ADC, External Reference – Electrical Characteristics (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
Positive external reference input
voltage range (2)
VeREF+
VeREF– ≤ VeREF+ ≤ VCC – 0.15
V,SREF1 = 1, SREF0 = 1 (3)
–55°C to 125°C
1.4
3.0
–55°C to 125°C
0
1.2
V
–55°C to 125°C
1.4
VCC
V
Differential external reference
input voltage range,
ΔVeREF = VeREF+ – VeREF–
(1)
(2)
(3)
(4)
(5)
Static input current into VeREF–
UNIT
VCC
ΔVeREF
IVeREF–
MIN MAX
1.4
Negative external reference input
VeREF+ > VeREF–
voltage range (4)
Static input current into VeREF+
VCC
–55°C to 125°C
VeREF–
IVeREF+
TA
VeREF+ > VeREF–,
SREF1 = 1, SREF0 = 0
VeREF+ > VeREF–
V
(5)
0 V ≤ VeREF+ ≤ VCC,
SREF1 = 1, SREF0 = 0
–55°C to 125°C
2.2 V/3 V
±1
0 V ≤ VeREF+ ≤ VCC – 0.15 V ≤ 3
V,
SREF1 = 1, SREF0 = 1(3)
–55°C to 125°C
2.2 V/3 V
0
0 V ≤ VeREF– ≤ VCC
–55°C to 125°C
2.2 V/3 V
±1
mA
mA
The external reference is used during conversion to charge and discharge the capacitance array. The input capacitance, CI, is also the
dynamic load for an external reference during conversion. The dynamic impedance of the reference supply should follow the
recommendations on analog-source impedance to allow the charge to settle for 10-bit accuracy.
The accuracy limits the minimum positive external reference voltage. Lower reference voltage levels may be applied with reduced
accuracy requirements.
Under this condition the external reference is internally buffered. The reference buffer is active and requires the reference buffer supply
current IREFB. The current consumption can be limited to the sample and conversion period with REBURST = 1.
The accuracy limits the maximum negative external reference voltage. Higher reference voltage levels may be applied with reduced
accuracy requirements.
The accuracy limits the minimum external differential reference voltage. Lower differential reference voltage levels may be applied with
reduced accuracy requirements.
10-Bit ADC, Timing Parameters – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
VCC
MIN
ADC10SR=0
–55°C to 125°C
2.2 V/3 V
0.45
TYP
MAX
6.5
ADC10SR=1
–55°C to 125°C
2.2 V/3 V
0.45
1.5
fADC10CLK
ADC10 input clock
frequency
For specified
performance of ADC10
linearity parameters
fADC10OSC
ADC10 built-in
oscillator frequency
ADC10DIVx = 0, ADC10SSELx = 0,
fADC10CLK = fADC10OSC
–55°C to 125°C
2.2 V/3 V
3.25
6.45
ADC10 built-in oscillator,
ADC10SSELx = 0,
fADC10CLK = fADC10OSC
–55°C to 125°C
2.2 V/3 V
2.06
3.51
tCONVERT
Conversion time
fADC10CLK from ACLK, MCLK, or
SMCLK: ADC10SSELx ≠ 0
tADC10ON
(1)
42
Turn-on settling time
of the ADC
–55°C to 125°C
(1)
–55°C to 125°C
UNIT
MHz
MHz
ms
13 =
ADC10DIVx
1/fADC10CLK
100
ns
The condition is that the error in a conversion started after tADC10ON is less than ±0.5 LSB. The reference and input signal are already
settled.
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
10-Bit ADC, Linearity Parameters – Electrical Characteristics (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
TA
VCC
TYP MAX
UNIT
EI
Integral linearity error
PARAMETER
–55°C to 125°C
2.2 V/3 V
±1
LSB
ED
Differential linearity error
–55°C to 125°C
2.2 V/3 V
±1
LSB
EO
Offset error
Source impedance RS < 100 Ω
–55°C to 125°C
2.2 V/3 V
±1
LSB
SREFx = 010, un-buffered external
reference,
VeREF+ = 1.5 V
–55°C to 125°C
2.2 V
±1.1
±2
SREFx = 010; un-buffered external
reference,
VeREF+ = 2.5 V
–55°C to 125°C
3V
±1.1
±2
SREFx = 011, buffered external
reference (2),
VeREF+ = 1.5 V
–55°C to 125°C
2.2 V
±1.1
±4
SREFx = 011, buffered external
reference (2),
VeREF+ = 2.5 V
–55°C to 125°C
3V
±1.1
±3
SREFx = 010, unbuffered external
reference,
VeREF+ = 1.5 V
–55°C to 125°C
2.2 V
±2
±5
SREFx = 010, unbuffered external
reference,
VeREF+ = 2.5 V
–55°C to 125°C
3V
±2
±5
SREFx = 011, buffered external
reference (2),
VeREF+ = 1.5 V
–55°C to 125°C
2.2 V
±2
±7
SREFx = 011, buffered external
reference (2),
VeREF+ = 2.5 V
–55°C to 125°C
3V
±2
±6
EG
ET
(1)
(2)
Gain error
Total unadjusted error
TEST CONDITIONS
MIN
LSB
LSB
2.2V Not Production Tested.
The reference buffer's offset adds to the gain and total unadjusted error.
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
43
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
10-Bit ADC, Temperature Sensor and Built-In VMID – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
Temperature sensor
supply current (1)
ISENSOR
REFON = 0, INCHx = 0Ah,
TA = 25°C
ADC10ON = 1, INCHx = 0Ah
TCSENSOR
VOffset,Sensor
VSensor
Sensor offset voltage
Sensor output voltage
(3)
tSensor(sample Sample time required
if channel 10 is selected
)
(4)
TA
VCC
–55°C to 125°C
3V
60
160
–55°C to 125°C
-100
Temperature sensor voltage at
TA = 125°C(T version only)
–55°C to 125°C
1265 1365 1465
Temperature sensor voltage at
TA = 85°C
–55°C to 125°C
2.2 V/3 V
3.44
3.55
Temperature sensor voltage at
TA = 25°C
–55°C to 125°C
985 1085 1185
Temperature sensor voltage at
TA = 0°C
–55°C to 125°C
895
ADC10ON = 1, INCHx = 0Ah,
Error of conversion result ≤ 1
LSB
–55°C to 125°C
VMID
VCC divider at channel 11
ADC10ON = 1, INCHx = 0Bh,
VMID is Ⅹ 0.5 × VCC
–55°C to 125°C
tVMID(sample)
Sample time required
if channel 11 is selected
ADC10ON = 1, INCHx = 0Bh,
Error of conversion result ≤ 1
LSB
–55°C to 125°C
UNIT
mA
3.66 mV/°C
100
mV
1195 1295 1395
2.2 V/3 V
–55°C to 125°C
(3)
(4)
(5)
(6)
120
ADC10ON = 1, INCHx =
0Ah (2)
ADC10ON = 1, INCHx = 0Bh
(2)
40
–55°C to 125°C
Current into divider
at channel 11 (5)
(1)
TYP MAX
(2)
IVMID
(6)
MIN
2.2 V
mV
2.2 V/3 V
995 1095
30
ms
2.2 V
NA
3V
NA
2.2 V
1.06
1.1
1.14
3V
1.46
1.5
1.54
2.2 V
1400
3V
1220
mA
V
ns
The sensor current ISENSOR is consumed if (ADC10ON = 1 and REFON = 1) or (ADC10ON = 1 and INCH = 0Ah and sample signal is
high). When REFON = 1, ISENSOR is included in IREF+. When REFON = 0, ISENSOR applies during conversion of the temperature sensor
input (INCH = 0Ah).
The following formula can be used to calculate the temperature sensor output voltage:
VSensor,typ = TCSensor (273 + T [°C] ) + VOffset,sensor [mV] or
VSensor,typ = TCSensor T [°C] + VSensor(TA = 0°C) [mV]
Results based on characterization and/or production test, not TCSensor or VOffset,sensor.
The typical equivalent impedance of the sensor is 51 kΩ. The sample time required includes the sensor-on time tSENSOR(on).
No additional current is needed. The VMID is used during sampling.
The on-time tVMID(on) is included in the sampling time tVMID(sample); no additional on time is needed.
Operational Amplifier (OA) Supply Specifications – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
VCC
Supply voltage range
ICC
Supply current (1)
PSSR
(1)
44
Power-supply rejection ratio
TEST CONDITIONS
TA
VCC
–55°C to 125°C
Fast Mode
–55°C to 125°C
Medium Mode
–55°C to 125°C
Slow Mode
–55°C to 125°C
Noninverting
MIN
TYP
2.2
2.2 V/3 V
2.2 V/3 V
MAX
3.6
180
290
110
190
50
80
70
UNIT
V
mA
dB
Corresponding pins configured as OA inputs and outputs, respectively.
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
Operational Amplifier (OA) Input/Output Specifications – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VI/P
Input voltage range
Ilkg
Input leakage
current (1) (2)
TA
VCC
MIN
–15
±0.5
15
–20
±5
20
55°C to 85°C
2.2 V/3 V
–50
fV(I/P) = 1 kHz
80
140
fV(I/P) = 10 kHz
50
Slow Mode
65
Offset voltage, I/P
–55°C to 125°C
Offset temperature
drift, I/P
(3)
Offset voltage drift
with supply, I/P
0.3 V ≤ VIN ≤ VCC – 1.0 V
ΔVCC ≤ ±10%, TA = 25°C
–55°C to 125°C
High-level output
voltage,
O/P
Fast Mode, ISOURCE ≤ –500 mA
–55°C to 125°C
Slow Mode, ISOURCE ≤ –150 mA
–55°C to 125°C
Low-level output
voltage,
O/P
Fast Mode, ISOURCE ≤ 500 mA
–55°C to 125°C
Slow Mode, ISOURCE ≤ 150 mA
–55°C to 125°C
2.2 V/3 V
(1)
(2)
(3)
(4)
Common-mode
rejection ratio
±10
2.2 V/3 V
2.2 V/3 V
2.2 V/3 V
mV
mV/°C
±1.5
VCC –
0.2
VCC
VCC –
0.1
VCC
VSS
0.2
VSS
0.1
mV/V
V
V
150
RLoad = 3 kΩ, CLoad = 50 pF,
VO/P(OAx) > VCC – 1.2 V
2.2 V/3 V
RLoad = 3 kΩ, CLoad = 50 pF,
0.2 V ≤ VO/P(OAx) ≤ VCC – 0.2 V
CMRR
±10
2.2 V/3 V
RLoad = 3 kΩ, CLoad = 50 pF,
VO/P(OAx) < 0.2 V
Output resistance (4)
(see Figure 25)
nV/√Hz
30
Medium Mode
RO/P(OAx)
nA
50
50
Medium Mode
VOL
V
–55°C to 55°C
Voltage noise density, Slow Mode
I/P
Fast Mode
VOH
UNIT
–0.1
Fast Mode
VIO
MAX
VCC 1.2
–55°C to 125°C
85°C to 125°C
Vn
TYP
150
Ω
0.1
Noninverting
2.2 V/3 V
70
dB
ESD damage can degrade input current leakage.
The input bias current is overridden by the input leakage current.
Calculated using the box method
Specification valid for voltage-follower OAx configuration
ILoad
RLoad
AV CC
OAx
O/P(OAx)
RO/P(OAx)
Max
2
CLoad
Min
0.2V
AV CC−0.2V AV
V
CC OUT
Figure 25. OAx Output Resistance Tests
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
45
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
Operational Amplifier (OA) Dynamic Specifications – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
SR
TEST CONDITIONS
Slew rate
TA
VCC
MIN
TYP
Fast Mode
1.2
Medium Mode
0.8
Slow Mode
0.3
Open-loop voltage gain
fm
UNIT
V/ms
100
dB
Phase margin
CL = 50 pF
60
deg
Gain margin
CL = 50 pF
20
dB
Noninverting, Fast Mode,
RL = 47 kΩ, CL = 50 pF
2.2
Gain-bandwidth product
(see Figure 26 and Figure 27)
GBW
MAX
Noninverting, Medium Mode,
RL = 300 kΩ, CL = 50 pF
2.2 V/3 V
1.4
Noninverting, Slow Mode,
RL = 300 kΩ, CL = 50 pF
ten(on)
Enable time on
ten(off)
Enable time off
MHz
0.5
ton, noninverting, Gain = 1
–55°C to 125°C
2.2 V/3 V
–55°C to 125°C
2.2 V/3 V
TYPICAL OPEN-LOOP GAIN vs FREQUENCY
10
20
ms
1
ms
TYPICAL PHASE vs FREQUENCY
140
0
120
100
−50
80
Fast Mode
Fast Mode
Phase − degrees
Gain − dB
60
40
Medium Mode
20
0
Slow Mode
−100
Medium Mode
−150
−20
Slow Mode
−40
−200
−60
−80
1
10
100
1000
10000
100000
Input Frequency − kHz
−250
1
10
100
1000
10000
100000
Input Frequency − kHz
Figure 26.
Figure 27.
Operational Amplifier OA Feedback Network, Resistor Network – Electrical Characteristics (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
Rtotal
Total resistance of resistor
string
Runit
Unit resistor of resistor string (2)
(1)
(2)
46
TEST CONDITIONS
TA
MIN
TYP
MAX
UNIT
96
kΩ
6
kΩ
A single resistor string is composed of 4 Runit + 4 Runit + 2 Runit + 2 Runit + 1 Runit + 1 Runit + 1 Runit + 1 Runit = 16 Runit = Rtotal.
For the matching (i.e., the relative accuracy) of the unit resistors on a device, refer to the gain and level specifications of the respective
configurations.
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
Operational Amplifier (OA) Feedback Network, Comparator Mode (OAFCx = 3) – Electrical
Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
VLevel
Comparator level
TEST CONDITIONS
TA
VCC
MIN
TYP
MAX
OAFBRx = 1, OARRIP = 0
–55°C to 125°C
0.242
1/4
0.262
OAFBRx = 2, OARRIP = 0
–55°C to 125°C
0.492
½
0.512
OAFBRx = 3, OARRIP = 0
–55°C to 125°C
0.619
5/8
0.639
OAFBRx = 4, OARRIP = 0
N/A (1)
OAFBRx = 5, OARRIP = 0
N/A (1)
OAFBRx = 6, OARRIP = 0
N/A (1)
OAFBRx = 7, OARRIP = 0
OAFBRx = 1, OARRIP = 1
–55°C to 125°C
OAFBRx = 2, OARRIP = 1
–55°C to 125°C
OAFBRx = 3, OARRIP = 1
–55°C to 125°C
OAFBRx = 4, OARRIP = 1
OAFBRx = 5, OARRIP = 1
OAFBRx = 6, OARRIP = 1
2.2 V/3 V
N/A (1)
0.057
1/16
0.071
0.122
1/8
0.128
0.182
3/16
0.197
–55°C to 125°C
0.242
1/4
0.262
–55°C to 125°C
0.367
3/8
0.383
–55°C to 125°C
0.492
½
0.512
Fast Mode, Overdrive 10 mV
40
Fast Mode, Overdrive 100 mV
4
Fast Mode, Overdrive 500 mV
3
Medium Mode, Overdrive 10 mV
Propagation delay
(low-high and high-low)
60
Medium Mode, Overdrive 100 mV
2.2 V/3 V
6
Medium Mode, Overdrive 500 mV
(1)
VCC
N/A (1)
OAFBRx = 7, OARRIP = 1
tPLH, tPHL
UNIT
ms
5
Slow Mode, Overdrive 10 mV
160
Slow Mode, Overdrive 100 mV
20
Slow Mode, Overdrive 500 mV
15
The level is not available due to the analog input voltage range of the operational amplifier.
Operational Amplifier (OA) Feedback Network, Noninverting Amplifier Mode (OAFCx = 4) –
Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
G
Gain
MIN
TYP
MAX UNIT
OAFBRx = 0
TEST CONDITIONS
–55°C to 125°C
0.970
1.00
1.035
OAFBRx = 1
–55°C to 125°C
1.325
1.334
1.345
OAFBRx = 2
–55°C to 125°C
1.985
2.001
2.017
OAFBRx = 3
–55°C to 125°C
2.638
2.667
2.696
OAFBRx = 4
–55°C to 125°C
3.94
4.00
4.06
OAFBRx = 5
–55°C to 125°C
5.22
5.33
5.44
OAFBRx = 6
–55°C to 125°C
7.76
7.97
8.18
OAFBRx = 7
–55°C to 125°C
15.0
15.8
16.7
THD
Total harmonic
distortion/nonlinearity
All gains
tSettle
Settling time (1)
All power modes
(1)
TA
–55°C to 125°C
VCC
2.2 V/3 V
2.2 V
–60
3V
–70
2.2 V/3 V
7
dB
12
ms
The settling time specifies the time until an ADC result is stable. This includes the minimum required sampling time of the ADC. The
settling time of the amplifier itself might be faster.
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
47
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
Operational Amplifier (OA) Feedback Network, Inverting Amplifier Mode (OAFCx = 6) –
Electrical Characteristics (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
G
Gain
TEST CONDITIONS
VCC
MIN
TYP
MAX UNIT
OAFBRx = 1
–55°C to 125°C
-0.385
–0.335
-0.305
OAFBRx = 2
–55°C to 125°C
-1.023
–1.002
-0.979
OAFBRx = 3
–55°C to 125°C
-1.712
–1.668
-1.624
OAFBRx = 4
–55°C to 125°C
-3.10
–3.00
-2.90
OAFBRx = 5
–55°C to 125°C
-4.51
–4.33
-4.15
OAFBRx = 6
–55°C to 125°C
-7.37
–6.97
-6.57
OAFBRx = 7
–55°C to 125°C
-16.6
–14.8
-13.1
THD
Total harmonic
distortion/nonlinearity
All gains
tSettle
Settling time (2)
All power modes
(1)
(2)
TA
–55°C to 125°C
2.2 V/3 V
2.2 V
–60
3V
–70
2.2 V/3 V
dB
7
12
ms
This includes the 2 OA configuration "inverting amplifier with input buffer". Both OA needs to be set to the same power mode OAPMx.
The settling time specifies the time until an ADC result is stable. This includes the minimum required sampling time of the ADC. The
settling time of the amplifier itself might be faster.
Flash Memory – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST
CONDITIO
NS
TA
VCC
MIN
TYP MAX
UNIT
2.2
3.6
V
VCC(PGM/ERASE) Program and erase supply voltage
–55°C to 125°C
fFTG
Flash timing generator frequency
–55°C to 125°C
476
kHz
IPGM
Supply current from VCC during program
–55°C to 125°C
2.2 V/3.6 V
1
5
mA
IERASE
Supply current from VCC during erase
–55°C to 125°C
2.2 V/3.6 V
1
10.5
mA
10
ms
(1)
257
tCPT
Cumulative program time
–55°C to 125°C
2.2 V/3.6 V
tCMErase
Cumulative mass erase time
–55°C to 125°C
2.2 V/3.6 V
Program/Erase endurance
–55°C to 125°C
20
104
ms
105
cycles
tRetention
Data retention duration (2)
TJ = 25°C
tWord
Word or byte program time
(3)
30
tFTG
tBlock,
0
Block program time for 1st byte or word
(3)
25
tFTG
1-63
Block program time for each additional
byte or word
(3)
18
tFTG
Block program end-sequence wait time
(3)
6
tFTG
tFTG
tFTG
tBlock,
tBlock,
End
100
years
tMass Erase
Mass erase time
(3)
1059
3
tSeg Erase
Segment erase time
(3)
4819
(1)
(2)
(3)
48
The cumulative program time must not be exceeded when writing to a 64-byte flash block. This parameter applies to all programming
methods: individual word/byte write and block write modes.
To test the flash data retention at various temperatures we make use of accelerated tests on the flash with 500-Hours Baking Time at
250°C. These tests are wholly based on Arrhenius law and equation. For more information refer to Figure 28.
These values are hardwired into the Flash Controller's state machine (tFTG = 1/fFTG).
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
30
25
Time - (Yrs)
20
15
10
5
0
85
90
95
100
105
110
115
120
125
130
135
140
145
150
Junction Temperature - T J (C)
Figure 28. Flash Data Retention vs Junction Temperature
RAM – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
V(RAMh)
(1)
RAM retention supply voltage
TEST CONDITIONS
(1)
TA
CPU halted
MIN MAX
–55°C to 125°C
UNIT
1.6
V
This parameter defines the minimum supply voltage VCC when the data in RAM remains unchanged. No program execution should
happen during this supply voltage condition.
JTAG and Spy-Bi-Wire Interface – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
fSBW
TEST CONDITIONS
Spy-Bi-Wire input frequency
tSBW,Low Spy-Bi-Wire low clock pulse length
TA
VCC
MIN
TYP MAX
UNIT
–55°C to 125°C
2.2 V/3 V
0
20
MHz
–55°C to 125°C
2.2 V/3 V
0.02
5
15
ms
1
ms
100
ms
tSBW,En
Spy-Bi-Wire enable time
(TEST high to acceptance of first clock
edge (1))
–55°C to 125°C
2.2 V/3 V
tSBW,Ret
Spy-Bi-Wire return to normal operation
time
–55°C to 125°C
2.2 V/3 V
15
fTCK
TCK input frequency (2)
–55°C to 125°C
2.2 V
0
5
MHz
3V
0
10
MHz
RInternal
Internal pulldown resistance on TEST
–55°C to 125°C
2.2 V/3 V
25
90
kΩ
(1)
(2)
60
Tools accessing the Spy-Bi-Wire interface need to wait for the maximum tSBW,En time after pulling the TEST/SBWCLK pin high before
applying the first SBWCLK clock edge.
fTCK may be restricted to meet the timing requirements of the module selected.
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
49
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
JTAG Fuse (1) – Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
MIN
TA = 25°C
2.5
MAX
UNIT
VCC(FB)
Supply voltage during fuse-blow condition
VFB
Voltage level on TEST for fuse blow
–40°C to 125°C
IFB
Supply current into TEST during fuse blow
–40°C to 125°C
100
mA
tFB
Time to blow fuse
–40°C to 125°C
1
ms
(1)
50
6
V
7
V
Once the fuse is blown, no further access to the JTAG/Test, Spy-Bi-Wire, and emulation feature is possible, and JTAG is switched to
bypass mode.
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
APPLICATION INFORMATION
Port P1 Pin Schematic: P1.0 to P1.3, Input/Output With Schmitt Trigger
Pad Logic
P1REN.x
P1DIR.x
0
0
Module X OUT
1
0
1
1
Direction
0: Input
1: Output
1
P1OUT.x
DVSS
DVCC
P1.0/TACLK/ADC10CLK
P1.1/TA0
P1.2/TA1
P1.3/TA2
P1SEL.x
P1IN.x
EN
Module X IN
D
P1IE.x
P1IRQ.x
EN
Q
P1IFG.x
Set
Interrupt
Edge
Select
P1SEL.x
P1IES.x
Port P1 (P1.0 to P1.3) Pin Functions
PIN NAME (P1.X)
FUNCTION (1)
X
P1DIR.x
P1SEL.x
I: 0; O: 1
0
Timer_A3.TACLK
0
1
ADC10CLK
1
1
I: 0; O: 1
0
Timer_A3.CCI0A
0
1
Timer_A3.TA0
1
1
I: 0; O: 1
0
0
1
P1.0 (3)
P1.0/TACLK/ADC10CLK
0
P1.1
P1.1/TA0
1
(4)
(I/O)
P1.2 (4) (I/O)
P1.2/TA1
2
Timer_A3.CCI0A
Timer_A3.TA0
1
1
I: 0; O: 1
0
Timer_A3.CCI0A
0
1
Timer_A3.TA0
1
1
P1.3 (4) I/O
P1.3/TA2
(1)
(2)
(3)
(4)
3
CONTROL BITS/SIGNALS (2)
N/A: Not available or not applicable
X: Don't care
Default after reset (PUC/POR)
Default after reset (PUC/POR)
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
51
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
Port P1 Pin Schematic: P1.4 to P1.6, Input/Output With Schmitt Trigger and In-System Access
Features
Pad Logic
P1REN.x
P1DIR.x
0
0
Module X OUT
1
0
1
1
Direction
0: Input
1: Output
1
P1OUT.x
DVSS
DVCC
P1.4/SMCLK/TCK
P1.5/TA0/TMS
P1.6/TA1/TDI
Bus
Keeper
P1SEL.x
EN
P1IN.x
EN
Module X IN
D
P1IE.x
P1IRQ.x
EN
Q
P1IFG.x
Set
Interrupt
Edge
Select
P1SEL.x
P1IES.x
To JTAG
From JTAG
Port P1 (P1.4 to P1.6) Pin Functions
PIN NAME (P1.X)
CONTROL BITS/SIGNALS (2)
FUNCTION (1)
X
P1.4 (3) (I/O)
P1.4/SMCLK/TCK
4
5
6
52
0
1
1
0
X
X
1
I: 0; O: 1
0
0
Timer_A3.TA0
1
1
0
TMS
X
X
1
I: 0; O: 1
0
0
1
1
0
X
X
1
Timer_A3.TA1
TDI/TCLK
(1)
(2)
(3)
(4)
4-Wire JTAG
0
TCK
P1.6 (3) (I/O)
P1.6/TA1/TDI/TCLK
P1SEL.x
SMCLK
P1.5 (3) (I/O)
P1.5/TA0/TMS
P1DIR.x
I: 0; O: 1
(4)
N/A: Not available or not applicable
X: Don't care
Default after reset (PUC/POR)
Function controlled by JTAG
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
Port P1 Pin Schematic: P1.7, Input/Output With Schmitt Trigger and In-System Access Features
Pad Logic
P1REN.7
P1DIR.7
0
0
Module X OUT
1
0
1
1
Direction
0: Input
1: Output
1
P1OUT.7
DVSS
DVCC
P1.7/TA2/TDO/TDI
Bus
Keeper
P1SEL.7
EN
P1IN.7
EN
Module X IN
D
P1IE.7
P1IRQ.7
EN
Q
Set
P1IFG.7
Interrupt
Edge
Select
P1SEL.7
P1IES.7
To JTAG
From JTAG
From JTAG
From JTAG (TDO)
Port P1 (P1.7) Pin Functions
PIN NAME (P1.X)
FUNCTION (1)
X
P1.7 (3) (I/O)
P1.7/TA2/TDO/TDI
7
Timer_A3.TA2
TDO/TDI
(1)
(2)
(3)
(4)
(4)
CONTROL BITS/SIGNALS (2)
P1DIR.x
P1SEL.x
4-Wire JTAG
I: 0; O: 1
0
0
1
1
0
X
X
1
N/A: Not available or not applicable
X: Don't care
Default after reset (PUC/POR)
Function controlled by JTAG
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
53
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
Port P2 Pin Schematic: P2.0, P2.2, Input/Output With Schmitt Trigger
Pad Logic
To ADC 10
INCHx = y
ADC10AE0.y
P2REN.x
P2DIR.x
0
0
Module X OUT
1
0
1
1
Direction
0: Input
1: Output
1
P2OUT.x
DVSS
DVCC
P2.0/ACLK/A0/OA0I0
P2.2/TA0/A2/OA0I1
Bus
Keeper
P2SEL.x
EN
P2IN.x
EN
Module X IN
D
P2IE.x
P2IRQ.x
EN
Q
P2IFG.x
Set
Interrupt
Edge
Select
P2SEL.x
P2IES.x
+
OA0
−
Port P2 (P2.0, P2.2) Pin Functions
Pin Name (P2.X)
X
FUNCTION (1)
Y
P2.0 (3) (I/O)
P2.0/ACLK/A0/OA0I0
0
0
(1)
(2)
(3)
(4)
54
2
P2SEL.x
ADC10AE0.y
0
0
1
1
0
(4)
P2.2 (3) (I/O)
2
P2DIR.x
I: 0; O: 1
ACLK
A0/OA0I0
P2.2/TA0/A2/OA0I1
CONTROL BITS/SIGNALS (2)
X
X
1
I: 0; O: 1
0
0
0
1
0
Timer_A3.CCI0B
Timer_A3.TA0
1
1
0
A2/OA0I1 (4)
X
X
1
N/A: Not available or not applicable
X: Don't care
Default after reset (PUC/POR)
Setting the ADC10AE0.y bit disables the output driver as well as the input Schmitt trigger to prevent parasitic cross currents when
applying analog signals.
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
Port P2 Pin Schematic: P2.1, Input/Output With Schmitt Trigger
Pad Logic
To ADC 10
INCHx = 1
ADC10AE0.1
P2REN.1
P2DIR.1
0
0
Module X OUT
1
0
DVCC
1
1
Direction
0: Input
1: Output
1
P2OUT.1
DVSS
P2.1/TAINCLK/SMCLK/
A1/OA0O
Bus
Keeper
P2SEL.1
EN
P2IN.1
EN
Module X IN
D
P2IE.1
P2IRQ.1
EN
Q
P2IFG.1
Set
+
OA0
P2SEL.1
P2IES.1
OAADCx
OAFCx
OAPMx
Interrupt
Edge
Select
1
−
(OAADCx = 10 or OAFCx = 000) and OAPMx > 00
To OA0 Feedback Network
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
1
Submit Documentation Feedback
55
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
Port P2 Pin Schematic: P2.3, Input/Output With Schmitt Trigger
SREF2
VSS
0
To ADC 10 VR−
Pad Logic
1
To ADC 10
INCHx = 3
ADC10AE0.3
P2REN.3
P2DIR.3
0
0
Module X OUT
1
0
1
1
Direction
0: Input
1: Output
1
P2OUT.3
DVSS
DVCC
P2.3/TA1/
A3/VREF−/VeREF−/
OA1I1/OA1O
Bus
Keeper
P2SEL.3
EN
P2IN.3
EN
Module X IN
D
P2IE.3
P2IRQ.3
P2IFG.3
P2SEL.3
P2IES.3
OAADCx
OAFCx
OAPMx
EN
Q
Set
Interrupt
Edge
Select
+
1
OA1
−
(OAADCx = 10 or OAFCx = 000) and OAPMx > 00
To OA1 Feedback Network
56
Submit Documentation Feedback
1
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
Port P2 (P2.1) Pin Functions
PIN NAME (P2.X)
X
FUNCTION (1)
Y
P2.1
P2.1/TAINCLK/SMCLK/A1/OA0O
(1)
(2)
(3)
(4)
1
1
(3)
(I/O)
CONTROL BITS/SIGNALS (2)
P2DIR.x
P2SEL.x
ADC10AE0.y
I: 0; O: 1
0
0
Timer_A3.INCLK
0
1
0
SMCLK
1
1
0
A1/OA0O (4)
X
X
1
N/A: Not available or not applicable
X: Don't care
Default after reset (PUC/POR)
Setting the ADC10AE0.y bit disables the output driver as well as the input Schmitt trigger to prevent parasitic cross currents when
applying analog signals.
Port P2 (P2.3) Pin Functions
PIN NAME (P2.X)
X
Y
FUNCTION (1)
P2DIR.x
P2SEL.x
ADC10AE0.y
I: 0; O: 1
0
0
Timer_A3.CCI1B
0
1
0
Timer_A3.TA1
1
1
0
A3/VREF–/VeREF–/OA1I1/OA1O (4)
X
X
1
P2.3 (3) (I/O)
P2.3/TA1/A3/VREF–/VeREF–/OA1I1/OA1O
(1)
(2)
(3)
(4)
3
3
CONTROL BITS/SIGNALS (2)
N/A: Not available or not applicable
X: Don't care
Default after reset (PUC/POR)
Setting the ADC10AE0.y bit disables the output driver as well as the input Schmitt trigger to prevent parasitic cross currents when
applying analog signals.
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
57
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
Port P2 Pin Schematic: P2.4, Input/Output With Schmitt Trigger
Pad Logic
To /from ADC10
positive reference
To ADC 10
INCHx = 4
ADC10AE0.4
P2REN.4
P2DIR.4
0
0
Module X OUT
1
0
1
1
Direction
0: Input
1: Output
1
P2OUT.4
DVSS
DVCC
P2.4/TA2/
A4/VREF+/VeREF+/
OA1I0
Bus
Keeper
P2SEL.4
EN
P2IN.4
EN
Module X IN
D
P2IE.4
P2IRQ.4
EN
Q
P2IFG.4
Set
Interrupt
Edge
Select
P2SEL.4
P2IES.4
+
OA1
−
Port P2 (P2.4) Pin Functions
PIN NAME (P2.X)
X
Y
CONTROL BITS/SIGNALS (2)
FUNCTION (1)
P2.4 (3) (I/O)
P2.4/TA2/A4/VREF+/VeREF+/OA1I0
4
4
Timer_A3.TA2
A4/VREF+/VeREF+/OA1I0
(1)
(2)
(3)
(4)
58
(4)
P2DIR.x
P2SEL.x
ADC10AE0.y
I: 0; O: 1
0
0
1
1
0
X
X
1
N/A: Not available or not applicable
X: Don't care
Default after reset (PUC/POR)
Setting the ADC10AE0.y bit disables the output driver as well as the input Schmitt trigger to prevent parasitic cross currents when
applying analog signals.
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
Port P2 Pin Schematic: P2.5, Input/Output With Schmitt Trigger and External ROSC for DCO
Pad Logic
To DCO
DCOR
P1REN.x
P1DIR.x
0
P1OUT.x
0
1
0
DVCC
1
1
Direction
0: Input
1: Output
1
Module X OUT
DVSS
P2.5/ROSC
Bus
Keeper
P1SEL.x
EN
P1IN.x
EN
Module X IN
D
P1IE.x
EN
P1IRQ.x
Q
Set
P1IFG.x
Interrupt
Edge
Select
P1SEL.x
P1IES.x
Port P2 (P2.5) Pin Functions
PIN NAME (P2.X)
X
FUNCTION
P2.5
P2.5/ROSC
(1)
(2)
(3)
5
(2)
CONTROL BITS/SIGNALS (1)
P2DIR.x
P2SEL.x
DCOR
0/1
0
0
N/A (3)
(I/O)
0
1
0
DVSS
1
1
0
ROSC
X
X
1
X: Don't care
Default after reset (PUC/POR)
N/A: Not available or not applicable
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
59
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
Port P2 Pin Schematic: P2.6, Input/Output With Schmitt Trigger and Crystal Oscillator Input
BCSCTL3.LFXT1Sx = 11
LFXT1 Oscillator
P2.7/XOUT
LFXT1 off
0
LFXT1CLK
1
Pad Logic
P2SEL.7
P2REN.6
P2DIR.6
0
0
Module X OUT
1
0
DVCC
1
1
Direction
0: Input
1: Output
1
P2OUT.6
DVSS
P2.6/XIN
Bus
Keeper
P2SEL.6
EN
P2IN.6
EN
Module X IN
D
P2IE.6
P2IRQ.6
EN
Q
P2IFG.6
P2SEL.6
P2IES.6
Set
Interrupt
Edge
Select
Port P2 (P2.6) Pin Functions
PIN NAME (P2.X)
P2.6/XIN
(1)
(2)
(3)
60
6
CONTROL BITS/SIGNALS (2)
FUNCTION (1)
X
P2.6 (I/O)
XIN (3)
P2DIR.x
P2SEL.x
I: 0; O: 1
0
X
1
N/A: Not available or not applicable
X: Don't care
Default after reset (PUC/POR)
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
Port P2 Pin Schematic: P2.7, Input/Output With Schmitt Trigger and Crystal Oscillator Output
BCSCTL3.LFXT1Sx = 11
LFXT1 Oscillator
LFXT1 off
0
LFXT1CLK
From P2.6/XIN
1
P2.6/XIN
Pad Logic
P2SEL.6
P2REN.7
P2DIR.7
0
0
Module X OUT
1
0
DVCC
1
1
Direction
0: Input
1: Output
1
P2OUT.7
DVSS
P2.7/XOUT
Bus
Keeper
P2SEL.7
EN
P2IN.7
EN
Module X IN
D
P2IE.7
P2IRQ.7
EN
Q
Set
P2IFG.7
Interrupt
Edge
Select
P2SEL.7
P2IES.7
Port P2 (P2.7) Pin Functions
PIN NAME (P2.X)
XOUT/P2.7
(1)
(2)
(3)
(4)
FUNCTION (1)
X
6
CONTROL BITS/SIGNALS (2)
P2DIR.x
P2SEL.x
P2.7 (I/O)
I: 0; O: 1
0
XOUT (3)
X
1
(4)
N/A: Not available or not applicable
X: Don't care
Default after reset (PUC/POR)
If the pin XOUT/P2.7 is used as an input a current can flow until P2SEL.7 is cleared due to the oscillator output driver connection to this
pin after reset.
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
61
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
Port P3 Pin Schematic: P3.0, Input/Output With Schmitt Trigger
Pad Logic
To ADC 10
INCHx = 5
ADC10AE0.5
P3REN.0
P3DIR.0
USCI Direction
Control
0
P3OUT.0
0
Module X OUT
1
DVSS
0
DVCC
1
1
Direction
0: Input
1: Output
1
P3.0/UC1STE/UC0CLK/A5
Bus
Keeper
P3SEL.0
EN
P3IN.0
EN
Module X IN
D
Port P3 (P3.0) Pin Functions
PIN NAME (P1.X)
X
FUNCTION (1)
Y
P3.0 (3) (I/O)
P3.0/UC1STE/UC0CLK/A5
0
5
UC1STE/UC0CLK (4)
CONTROL BITS/SIGNALS (2)
P3DIR.x
P3SEL.x
ADC10AE0.y
I: 0; O: 1
0
0
X
1
0
X
X
1
(5)
A5 (6)
(1)
(2)
(3)
(4)
(5)
(6)
62
N/A: Not available or not applicable
X: Don't care
Default after reset (PUC/POR)
The pin direction is controlled by the USCI module.
UC0CLK function takes precedence over UC1STE function. If the pin is required as UC0CLK input or output USCI1 is forced to 3-wire
SPI mode if 4-wire SPI mode is selected.
Setting the ADC10AE0.y bit disables the output driver as well as the input Schmitt trigger to prevent parasitic cross currents when
applying analog signals.
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
Port P3 Pin Schematic: P3.1 to P3.5, Input/Output With Schmitt Trigger
Pad Logic
DVSS
P3REN.x
P3DIR.x
USCI Direction
Control
0
P3OUT.x
0
Module X OUT
1
DVSS
0
DVCC
1
1
Direction
0: Input
1: Output
1
P3.1/UC1SIMO/UC1SCL
P3.2/UC1SOMI/UC1SDA
P3.3/UC1CLK/UC0STE
P3.4/UC0TXD/UC0SIMO
P3.5/UC0RXD/UC0SOMI
Bus
Keeper
P3SEL.x
EN
P3IN.x
EN
Module X IN
D
Port P3 (P3.1 to P3.5) Pin Functions
PIN NAME (P3.X)
P3.1/UC1SIMO/UC1SDA
P3.2/UC1SOMI/UC1SCL
P3.3/UC1CLK/UC0STE
P3.4/UC0TXD/UC0SIMO
P3.5/UC0RXD/UC0SOMI
(1)
(2)
(3)
(4)
(5)
(6)
(7)
FUNCTION (1)
X
1
1
1
1
1
P3.1 (3) (I/O)
UC1SIMO/UC1SDA (4)
P3.2 (5) (I/O)
UC1SOMI/UC1SCL
(6)
P3.3 (5) (I/O)
UC1CLK/UC0STE (6)
P3.4
(5)
(7)
(I/O)
UC0TXD/UC0SIMO (6)
P3.5 (5) (I/O)
UC0RXD/UC0SOMI
(6)
CONTROL BITS/SIGNALS (2)
P3DIR.x
P3SEL.x
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
I: 0; O: 1
0
X
1
N/A: Not available or not applicable
X: Don't care
Default after reset (PUC/POR)
The pin direction is controlled by the USCI module.
Default after reset (PUC/POR)
The pin direction is controlled by the USCI module.
UC1CLK function takes precedence over UC0STE function. If the pin is required as UC1CLK input or output, USCI0 is orced to 3-wire
SPI mode even if 4-wire SPI mode is selected.
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
63
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
Port P3 Pin Schematic: P3.6 to P3.7, Input/Output With Schmitt Trigger
Pad Logic
To ADC 10
INCHx = y
ADC10AE0.y
P3REN.x
P3DIR.x
0
0
Module X OUT
1
0
DVCC
1
1
Direction
0: Input
1: Output
1
P3OUT.x
DVSS
P3.6/A6/OA0I2
P3.7/A7/OA1I2
Bus
Keeper
P3SEL.x
EN
P3IN.x
EN
Module X IN
D
+
OA0/1
−
Port P3 (P3.6, P3.7) Pin Functions
PIN NAME (P3.X)
P3.6/A6/OA0I2
P3.7/A7/OA1I2
(1)
(2)
(3)
(4)
(5)
64
X
6
7
FUNCTION (1)
Y
6
7
CONTROL BITS/SIGNALS (3)
(2)
P3DIR.x
P3SEL.x
ADC10AE0.y
P3.6 (4) (I/O)
I: 0; O: 1
0
0
A6/OA0I2 (5)
X
X
1
P3.7 (4) (I/O)
I: 0; O: 1
0
0
X
X
1
A7/OA1I2
(5)
N/A: Not available or not applicable
UC0CLK function takes precedence over UC0STE function. If the pin is required as UC1CLK input or output, USCI0 is forced to 3-wire
SPI mode if 4-wire SPI mode is selected.
X: Don't care
Default after reset (PUC/POR)
Setting the ADC10AE0.y bit disables the output driver as well as the input Schmitt trigger to prevent parasitic cross currents when
applying analog signals.
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
Port P4 Pin Schematic: P4.0 to P4.2, Input/Output With Schmitt Trigger
Timer_B Output Tristate Logic
P4.6/TBOUTH/A15/OA1I3
P4SEL.6
P4DIR.6
ADC10AE1.7
Pad Logic
P4REN.x
P4DIR.x
0
0
Module X OUT
1
0
1
1
Direction
0: Input
1: Output
1
P4OUT.x
DVSS
DVCC
P4.0/TB0
P4.1/TB1
P4.2/TB2
Bus
Keeper
P4SEL.x
EN
P4IN.x
EN
Module X IN
D
Port P4 (P4.0 to P4.2) Pin Functions
PIN NAME (P4.X)
FUNCTION (1)
X
P4DIR.x
P4SEL.x
I: 0; O: 1
0
Timer_B3.CCI0A
0
1
Timer_B3.TB0
1
1
P4.0 (2) (I/O)
P4.0/TB0
0
P4.1
P4.1/TB1
1
(1)
(2)
2
(2)
I: 0; O: 1
0
Timer_B3.CCI1A
0
1
Timer_B3.TB1
1
1
P4.2
P4.2/TB2
CONTROL BITS/SIGNALS
(2)
(I/O)
I: 0; O: 1
0
Timer_B3.CCI2A
(I/O)
0
1
Timer_B3.TB2
1
1
N/A: Not available or not applicable.
Default after reset (PUC/POR)
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
65
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
Port P4 Pin Schematic: P4.3 to P4.4, Input/Output With Schmitt Trigger
Timer_B Output Tristate Logic
P4.6/TBOUTH/A15/OA1I3
P4SEL.6
P4DIR.6
ADC10AE1.7
Pad Logic
To ADC 10
†
INCHx = 8+y
ADC10AE1.y
P4REN.x
P4DIR.x
0
0
Module X OUT
1
0
1
1
Direction
0: Input
1: Output
1
P4OUT.x
DVSS
DVCC
P4.3/TB0/A12/OA0O
P4.4/TB1/A13/OA1O
Bus
Keeper
P4SEL.x
EN
P4IN.x
EN
Module X IN
D
+
1
OA0/1
−
OAADCx
OAPMx
OAADCx = 01 and OAPMx > 00
To OA0/1 Feedback Network
1
†
If OAADCx = 11 and not OAFCx = 000, the ADC input A12 or A13 is internally connected to the OA0 or OA1 output,
respectively, and the connections from the ADC and the operational amplifiers to the pad are disabled.
66
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
Port P4 (P4.3 to P4.4) Pin Functions
PIN NAME (P4.X)
X
FUNCTION (1)
Y
P4.3
P4.3/TB0/A12/OA0O
3
4
4
5
ADC10AE1.y
0
0
0
1
0
Timer_B3.TB0
1
1
0
A12/OA0O (4)
X
X
1
I: 0; O: 1
0
0
Timer_B3.CCI1B
(I/O)
0
1
0
Timer_B3.TB1
1
1
0
X
X
1
A13/OA1O
(1)
(2)
(3)
(4)
P4SEL.x
I: 0; O: 1
(3)
(I/O)
P4DIR.x
Timer_B3.CCI0B
P4.4
P4.4/TB1/A13/OA1O
(3)
CONTROL BITS/SIGNALS (2)
(4)
N/A: Not available or not applicable
X: Don't care
Default after reset (PUC/POR)
Setting the ADC10AE1.y bit disables the output driver as well as the input Schmitt trigger to prevent parasitic cross currents when
applying analog signals.
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
67
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
Port P4 Pin Schematic: P4.5, Input/Output With Schmitt Trigger
Timer_B Output Tristate Logic
P4.6/TBOUTH/A15/OA1I3
P4SEL.6
P4DIR.6
ADC10AE1.7
Pad Logic
To ADC 10
INCHx = 14
ADC10AE1.6
P4REN.5
P4DIR.5
0
0
Module X OUT
1
0
1
1
Direction
0: Input
1: Output
1
P4OUT.5
DVSS
DVCC
P4.5/TB3/A14/OA0I3
Bus
Keeper
P4SEL.5
EN
P4IN.5
EN
Module X IN
D
+
OA0
−
Port P4 (P4.5) Pin Functions
PIN NAME (P4.X)
X
CONTROL BITS/SIGNALS (2)
FUNCTION (1)
Y
P4DIR.x
P4SEL.x
ADC10AE1.y
I: 0; O: 1
0
0
Timer_B3.TB2
1
1
0
A14/OA0I3 (4)
X
X
1
P4.5 (3) (I/O)
P4.5/TB3/A14/OA0I3
(1)
(2)
(3)
(4)
68
5
6
N/A: Not available or not applicable
X: Don't care
Default after reset (PUC/POR)
Setting the ADC10AE1.y bit disables the output driver as well as the input Schmitt trigger to prevent parasitic cross currents when
applying analog signals.
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
Port P4 Pin Schematic: P4.6, Input/Output With Schmitt Trigger
Pad Logic
To ADC 10
INCHx = 15
ADC10AE1.7
P4REN.6
P4DIR.6
0
0
Module X OUT
1
0
1
1
Direction
0: Input
1: Output
1
P4OUT.6
DVSS
DVCC
P4.6/TBOUTH/
A15/OA1I3
Bus
Keeper
P4SEL.6
EN
P4IN.6
EN
Module X IN
D
+
OA1
−
Port P4 (P4.6) Pin Functions
PIN NAME (P4.X)
X
FUNCTION (1)
Y
P4.6
P4.6/TBOUTH/A15/OA1I3
(1)
(2)
(3)
(4)
6
7
(3)
(I/O)
CONTROL BITS/SIGNALS (2)
P4DIR.x
P4SEL.x
ADC10AE1.y
I: 0; O: 1
0
0
TBOUTH
0
1
0
DVSS
1
1
0
A15/OA1I3 (4)
X
X
1
N/A: Not available or not applicable
X: Don't care
Default after reset (PUC/POR)
Setting the ADC10AE1.y bit disables the output driver as well as the input Schmitt trigger to prevent parasitic cross currents when
applying analog signals.
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
69
MSP430F2274-EP
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
www.ti.com
Port P4 Pin Schematic: P4.7, Input/Output With Schmitt Trigger
Pad Logic
DVSS
P4REN.x
P4DIR.x
0
0
Module X OUT
1
0
DVCC
1
1
Direction
0: Input
1: Output
1
P4OUT.x
DVSS
P4.7/TBCLK
Bus
Keeper
P4SEL.x
EN
P4IN.x
EN
Module X IN
D
Port P4 (Pr.7) Pin Functions
PIN NAME (P4.X)
CONTROL BITS/SIGNALS
FUNCTION (1)
X
P4DIR.x
P4SEL.x
I: 0; O: 1
0
Timer_B3.TBCLK
0
1
DVSS
1
1
P4.7 (2) (I/O)
P4.7/TBCLK
(1)
(2)
70
7
N/A: Not available or not applicable
Default after reset (PUC/POR)
Submit Documentation Feedback
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
MSP430F2274-EP
www.ti.com
SLAS614B – SEPTEMBER 2008 – REVISED JANUARY 2010
JTAG Fuse Check Mode
MSP430 devices that have the fuse on the TEST terminal have a fuse check mode that tests the continuity of the
fuse the first time the JTAG port is accessed after a power-on reset (POR). When activated, a fuse check
current, ITF , of 1 mA at 3 V, 2.5 mA at 5 V can flow from the TEST pin to ground if the fuse is not burned. Care
must be taken to avoid accidentally activating the fuse check mode and increasing overall system power
consumption.
When the TEST pin is again taken low after a test or programming session, the fuse check mode and sense
currents are terminated.
Activation of the fuse check mode occurs with the first negative edge on the TMS pin after power up or if TMS is
being held low during power up. The second positive edge on the TMS pin deactivates the fuse check mode.
After deactivation, the fuse check mode remains inactive until another POR occurs. After each POR the fuse
check mode has the potential to be activated.
The fuse check current flows only when the fuse check mode is active and the TMS pin is in a low state (see
Figure 29). Therefore, the additional current flow can be prevented by holding the TMS pin high (default
condition).
Time TMS Goes Low After POR
TMS
ITF
ITEST
Figure 29. Fuse Check Mode Current, MSP430F22xx
NOTE
The CODE and RAM data protection is ensured if the JTAG fuse is blown and the
256-bit bootloader access key is used. Also, see the Bootstrap Loader section for
more information.
Copyright © 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): MSP430F2274-EP
Submit Documentation Feedback
71
PACKAGE OPTION ADDENDUM
www.ti.com
17-Feb-2010
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
MSP430F2274MDATEP
ACTIVE
TSSOP
DA
38
MSP430F2274MRHAEP
PREVIEW
VQFN
RHA
40
MSP430F2274MRHATEP
ACTIVE
VQFN
RHA
40
V62/08631-01XE
ACTIVE
VQFN
RHA
40
2000
Lead/Ball Finish
MSL Peak Temp (3)
TBD
Call TI
Call TI
TBD
Call TI
Call TI
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF MSP430F2274-EP :
• Catalog: MSP430F2274
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
6-Jan-2010
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
MSP430F2274MRHATEP
Package Package Pins
Type Drawing
VQFN
RHA
40
SPQ
250
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
180.0
16.4
Pack Materials-Page 1
6.3
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
6.3
1.5
12.0
16.0
Q2
PACKAGE MATERIALS INFORMATION
www.ti.com
6-Jan-2010
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
MSP430F2274MRHATEP
VQFN
RHA
40
250
190.5
212.7
31.8
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DLP® Products
www.dlp.com
Communications and
Telecom
www.ti.com/communications
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
www.ti.com/clocks
Consumer Electronics
www.ti.com/consumer-apps
Interface
interface.ti.com
Energy
www.ti.com/energy
Logic
logic.ti.com
Industrial
www.ti.com/industrial
Power Mgmt
power.ti.com
Medical
www.ti.com/medical
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
www.ti.com/video
Wireless
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated