LINER LT1799

Final Electrical Specifications
LTC1799
1kHz to 30MHz
Resistor Set SOT-23 Oscillator
U
DESCRIPTIO
FEATURES
■
■
■
■
■
■
■
■
■
■
■
■
One External Resistor Sets the Frequency
1kHz to 30MHz Frequency Range
SOT-23 Miniature Package
Frequency Error ≤1.5% 5kHz to 20MHz
(TA = 25°C)
Frequency Error ≤ 2% 5kHz to 20MHz
(TA = 0°C to 70°C)
±40ppm/°C Temperature Stability
0.05%/V Supply Stability
50% ±1% Duty Cycle 1kHz to 2MHz
50% ±5% Duty Cycle 2MHz to 20MHz
1mA Typical Supply Current
100Ω CMOS Output Driver
Operates from a Single 2.7V to 5.5V Supply
U
APPLICATIO S
■
■
■
■
■
■
■
Low Cost Precision Oscillator
Charge Pump Driver
Switching Power Supply Clock Reference
Clocking Switched Capacitor Filters
Fixed Crystal Oscillator Replacement
Ceramic Oscillator Replacement
Small Footprint Replacement for Econ Oscillators
January 2001
The LTC®1799 is a precision oscillator that is easy to use
and occupies very little PC board space. The oscillator
frequency is programmed by a single external resistor
(RSET). The LTC1799 has been designed for high accuracy
operation (≤1.5% frequency error) without the need for
external trim components.
The LTC1799 operates with a single 2.7V to 5.5V power
supply and provides a rail-to-rail, 50% duty cycle square
wave output. The CMOS output driver ensures fast rise/fall
times and rail-to-rail switching. The frequency-setting
resistor can vary from 3.32k to 1M to select a master
oscillator frequency between 100kHz and 30MHz (5V
supply). The three-state DIV input determines whether the
master clock is divided by 1, 10 or 100 before driving the
output, providing three frequency ranges spanning 1kHz
to 30MHz (5V supply). The LTC1799 features a proprietary
feedback loop that linearizes the relationship between
RSET and frequency, eliminating the need for tables to
calculate frequency. The oscillator can be easily programmed using the simple formula outlined below:
fOSC
100, DIV PIN = V +
 10k 

= 10MHz • 
 , N = 10, DIV PIN = Hi - Z
 N • RSET 
1, DIV PIN = GND

, LTC and LT are registered trademarks of Linear Technology Corporation.
U
TYPICAL APPLICATIO
Typical Distribution of Frequency Error, TA = 25°C
25
Basic Connection
1
0.1µF
5k ≤ RSET ≤ 200k
2
3
V+
OUT
LTC1799
V+
GND
SET
DIV
1799 TA01
4
÷100
÷10
Hi-Z
15
10
÷10
GND
SOT-23 Actual Size
20
5kHz ≤ fOSC ≤ 20MHz
5
UNITS (%)
V+
5
0
–1.25
–0.75
–0.25 0 0.25
0.75
FREQUENCY ERROR (%)
1.25
1799 TA02
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
1
LTC1799
U
W
U
PACKAGE/ORDER I FOR ATIO
U
W W
W
ABSOLUTE
AXI U RATI GS
(Note 1)
Supply Voltage (V +) to GND ........................– 0.3V to 6V
DIV to GND .................................... – 0.3V to (V + + 0.3V)
SET to GND ................................... – 0.3V to (V + + 0.3V)
OUT to GND ................................... – 0.3V to (V + + 0.3V)
Operating Temperature Range
LTC1799C ............................................... 0°C to 70°C
LTC1799I ............................................ – 40°C to 85°C
Storage Temperature Range ................. – 65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
ORDER PART NUMBER
TOP VIEW
V+
5 OUT
1
LTC1799CS5
LTC1799IS5
GND 2
SET 3
4 DIV
S5 PART MARKING
S5 PACKAGE
5-LEAD PLASTIC SOT-23
LTND
LTNE
TJMAX = 125°C, θJA = 256°C/W
Consult factory for parts specified with wider operating temperature ranges.
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. V+ = 2.7V to 5.5V, RL=5k, CL = 5pF, Pin 4 = V+ unless otherwise noted.
All voltages are with respect to GND.
SYMBOL
∆f
PARAMETER
CONDITIONS
Frequency Accuracy
V+ = 5V
(Notes 2, 3)
V+ = 3V
MIN
5kHz < f < 20MHz
5kHz < f < 20MHz, LTC1799C
5kHz < f < 20MHz, LTC1799I
1kHz < f < 5kHz
20MHz < f < 30MHz
5kHz < f < 10MHz
5kHz < f < 10MHz, LTC1799C
5kHz < f < 10MHz, LTC1799I
1kHz < f < 5kHz
10MHz < f < 20MHz
TYP
MAX
UNITS
±0.5
±1.5
±2
±2.5
%
%
%
%
%
±1.5
±2
±2.5
%
%
%
%
%
200
200
kΩ
kΩ
●
●
±2.5
±2.5
±0.5
●
●
±2.5
±2.5
RSET
Frequency-Setting Resistor Range
∆f < 1.5%
V + = 5V
V + = 3V
fMAX
Maximum Frequency
∆f < 2.5%, Pin 4= 0V
V + = 5V
V + = 3V
fMIN
Minimum Frequency
∆f < 2.5%, Pin 4= V +
∆f/∆T
Freq Drift Over Temp (Note 3)
RSET = 31.6k
●
±0.004
∆f/∆V
Freq Drift Over Supply (Note 3)
V+ = 2.7V to 5.5V, RSET = 31.6k
●
0.05
Timing Jitter
(Note 4)
Pin 4 = V +
5
10
Pin 4 = Floating
Pin 4 = 0V
Long-Term Stability of Output Frequency
Duty Cycle
V+
IS
or Floating (DIV Either by 100 or 10)
Pin 4 = 0V (DIV by 1)
Operating Supply Range
Power Supply Current
VIH
High Level DIV Input Voltage
VIL
Low Level DIV Input Voltage
IDIV
DIV Input Current
2
Pin 4 = V +
RSET = 200k, Pin 4 = V +, RL
=0
V+
RSET = 10k, Pin 4 = 0V, No Load
V+
●
●
49
45
●
2.7
= 5V
●
= 5V
V + = 3V
●
●
30
20
MHz
MHz
1
kHz
%/°C
0.1
0.06
0.13
0.4
%
%
%
300
ppm/√kHr
50
50
0.7
51
55
%
%
5.5
V
1.1
mA
2.4
2
mA
mA
● V+ – 0.4
V
●
Pin 4 = V +
Pin 4 = 0V
●
●
%/V
5
–5
0.5
V
8
8
µA
µA
LTC1799
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. V+ = 2.7V to 5.5V, RL=5k, CL = 5pF, Pin 4 = V+ unless otherwise noted.
All voltages are with respect to GND.
SYMBOL
PARAMETER
CONDITIONS
VOH
High Level Output Voltage
V + = 5V
IOH = – 1mA
IOH = – 4mA
●
●
4.8
4.5
4.95
4.8
V
V
V + = 3V
IOH = – 1mA
IOH = – 4mA
●
●
2.7
2.2
2.9
2.6
V
V
V + = 5V
IOL = 1mA
IOL = 4mA
●
●
0.05
0.2
0.15
0.4
V
V
V + = 3V
IOL = 1mA
IOL = 4mA
●
●
0.1
0.4
0.3
0.7
V
V
V + = 5V
Pin 4 = V+ or Floating, RL = 0
Pin 4 = 0V, RL = 0
14
7
ns
ns
V + = 3V
Pin 4 = V+ or Floating, RL = 0
Pin 4 = 0V, RL = 0
19
11
ns
ns
V + = 5V
Pin 4 = V+ or Floating, RL = 0
Pin 4 = 0V, RL = 0
13
6
ns
ns
V + = 3V
Pin 4 = V+ or Floating, RL = 0
Pin 4 = 0V, RL = 0
19
10
ns
ns
VOL
Low Level Output Voltage
tr
OUT Rise Time
(Note 5)
tf
OUT Fall Time
(Note 5)
MIN
Note 1: Absolute Maximum Ratings are those values beyond which the life
of the device may be impaired.
Note 2: Frequencies near 100kHz and 1MHz may be generated using two
different values of RSET (see the Table 1 in the Applications Information
section). For these frequencies, the error is specified under the following
assumption: 10k < RSET ≤ 100k.
Note 3: Frequency error (defined as the deviation from the fOSC equation)
includes drift over temperature and over supply.
TYP
MAX
UNITS
Note 4: Jitter is the ratio of the peak-to-peak distribution of the period to
the mean of the period. This specification is based on characterization and
is not 100% tested.
Note 5: Output rise and fall times are measured between the 10% and
90% power supply levels. These specifications are based on
characterization.
U
U
U
PI FU CTIO S
V+ (Pin 1): Voltage Supply (2.7V ≤ V+ ≤ 5.5V). This supply
must be kept free from noise and ripple. It should be
bypassed directly to a ground plane.
GND (Pin 2): Ground. Should be tied to a ground plane for
best performance.
SET (Pin 3): Frequency-Setting Resistor Input. The value
of the resistor connected between this pin and V+ determines the oscillator frequency. The voltage on this pin is
held by the LTC1799 to approximately 1.1V below the V+
voltage. For best performance, use a precision metal film
resistor with a value between 10k and 200k and limit the
capacitance on this pin to less than 2pF.
DIV (Pin 4): Divider-Setting Input. This three-state input
selects among three divider settings, determining the
value of N in the frequency equation. Pin 4 should be tied
to GND for the ÷1 setting, the highest frequency range.
Floating Pin 4 divides the master oscillator by 10. Pin 4
should be tied to V+ for the ÷100 setting, the lowest
frequency range. To detect a floating DIV pin, the LTC1799
attempts to pull the pin toward midsupply. Therefore,
driving the DIV pin high requires sourcing approximately
5µA. Likewise, driving DIV low requires sinking 5µA.
When floated, the DIV pin will be held near midsupply by
these current sources. When it is floated, it is recommended that the DIV pin be bypassed by a 1nF capacitor
or surrounded by a ground shield to prevent excessive
coupling from other PCB traces.
OUT (Pin 5): Oscillator Output. This pin can easily drive
5kΩ or 10pF loads. Larger loads may cause inaccuracies
due to supply bounce at high frequencies.
3
LTC1799
U
W
U
U
APPLICATIO S I FOR ATIO
Table 1. Frequency Range vs Divider Setting
Selecting the Divider Setting and Resistor
The LTC1799’s master oscillator has a frequency range
spanning 0.1MHz to 30MHz. However, accuracy may
suffer if the master oscillator is operated at greater than
10MHz with a supply voltage lower than 4V. A programmable divider extends the frequency range to greater than
three decades. Table 1 describes the recommended frequencies for each divider setting. Note that the ranges
overlap; at some frequencies there are two divider/resistor
combinations that result in the desired frequency.
In general, any given oscillator frequency (fOSC) should be
obtained using the lowest master oscillator frequency.
Lower master oscillator frequencies use less power and
are more accuate. For instance, fOSC = 100kHz can be
obtained by either RSET = 10k, N = 100, master oscillator
= 10MHz or RSET = 100k, N = 10, master oscillator = 1MHz.
The RSET = 100k is preferred for lower power and better
accuracy.
DIVIDER SETTING
FREQUENCY RANGE
÷1
⇒
DIV (Pin 4) = GND
÷10
⇒
DIV (Pin 4) = Floating
÷100 ⇒
> 500kHz*
50kHz to 1MHz
DIV (Pin 4) = V+
< 100kHz
*At master oscillator frequencies greater than 10MHz (R
SET
< 10kΩ), the
LTC1799 may suffer reduced accuracy with a supply voltage less than 4V.
After choosing the proper divider setting, determine the
correct frequency-setting resistor. Because of the linear
correspondence between oscillation period and resistance, a simple equation relates resistance with frequency.
RSET = 10k • [10MHz/(N • fOSC)], N = 1, 10, 100
(RSETMIN = 3.32k (5V Supply), 5k (3V Supply),
RSETMAX = 1M)
Any resistor, RSET, tolerance adds to the inaccuracy of the
oscillator, fOSC.
Settling Time
The settling time is proportional to RSET and is approximately tSETTLE ≈ RSET • (5µs/kΩ). This parameter is
guaranteed by design and not 100% tested.
U
PACKAGE DESCRIPTIO
Dimensions in inches (millimeters) unless otherwise noted.
S5 Package
5-Lead Plastic SOT-23
(LTC DWG # 05-08-1633)
2.60 – 3.00
(0.102 – 0.118)
1.50 – 1.75
(0.059 – 0.069)
0.35 – 0.55
(0.014 – 0.022)
0.00 – 0.15
(0.00 – 0.006)
0.09 – 0.20
(0.004 – 0.008)
(NOTE 2)
0.35 – 0.50
0.90 – 1.30
(0.014 – 0.020)
(0.035 – 0.051)
FIVE PLACES (NOTE 2)
NOTE:
1. DIMENSIONS ARE IN MILLIMETERS
2. DIMENSIONS ARE INCLUSIVE OF PLATING
3. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR
4. MOLD FLASH SHALL NOT EXCEED 0.254mm
5. PACKAGE EIAJ REFERENCE IS SC-74A (EIAJ)
4
Linear Technology Corporation
0.90 – 1.45
(0.035 – 0.057)
2.80 – 3.00
(0.110 – 0.118)
(NOTE 3)
1.90
(0.074)
REF
0.95
(0.037)
REF
S5 SOT-23 0599
1799i LT/TP 0101 2K • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408)432-1900 ● FAX: (408) 434-0507 ● www.linear-tech.com
 LINEAR TECHNOLOGY CORPORATION 2001