Product Specification 2.125 Gb/s RoHS Compliant Short Wavelength 2x5 SFF Transceiver FTLF8519F2xCL PRODUCT FEATURES Up to 2.125 Gb/s bi-directional data links Standard 2x5 pin SFF footprint (MSA compliant) 850nm Oxide VCSEL laser transmitter Duplex LC connector RoHS compliant and Lead Free Up to 500m on 50/125μm MMF, 300m on 62.5/125μm MMF APPLICATIONS Metal enclosure, for lower EMI 1.25 Gb/s 1000Base-SX Ethernet Single 3.3V power supply Low power dissipation <750mW Dual Rate 1.063/2.125 Gb/s Fibre Channel Commercial operating temperature range: 0°C to 70°C Finisar’s FTLF8519F2xCL Small Form Factor (SFF) transceivers comply with the 2x5 standard package defined by the Small Form Factor Multi-Sourcing Agreement (MSA)1. They are simultaneously compatible with Gigabit Ethernet as specified in IEEE Std 802.32 and Fibre Channel FC-PI-2 10.03. They are RoHS compliant and lead-free per Directive 2002/95/EC4 and Finisar Application Note AN-2038. PRODUCT SELECTION FTLF8519F2xCL x G K H 2 Grounding Pins, Short EMI shield 2 Grounding Pins, Long EMI shield 6 Grounding Pins, Long EMI shield © Finisar Corporation April 7, 2006 Rev E Page 1 FTLF8519F2xCL 2x5 Pin SFF Product Specification – April 2006 I. Pin Descriptions Pin MS Symbol MS 1 2 3 4 5 6 7 8 9 10 VEER VCCR SD RDRD+ VCCT VEET TDIS TD+ TD- Name/Description Mounting Studs are for mechanical attachment and are connected to chassis ground. Chassis ground is internally isolated from circuit grounds. Connection to user’s ground plane is recommended. Receiver Ground (Common with Transmitter Ground) Receiver Power Supply Signal Detect. Logic 1 indicates normal operation. Receiver Inverted DATA out. AC Coupled Receiver Non-inverted DATA out. AC Coupled Transmitter Power Supply Transmitter Ground (Common with Receiver Ground) Transmitter Disable Transmitter Non-Inverted DATA in. AC Coupled. Transmitter Inverted DATA in. AC Coupled Logic Family NA NA NA LVTTL See Rx spec. See Rx spec. NA NA LVTTL See Tx spec. See Tx spec. MS 10 9 8 7 6 TOP VIEW 12345 MS II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Relative Humidity Hand Lead Soldering Temperature/Time Wave Lead Soldering Temperature/Time Symbol Vcc TS TOP RH Min -0.5 -40 0 0 Typ Max 4.0 85 70 85 260/10 260/10 Unit V °C °C % °C/s °C/s Ref. 1 Notes: 1. Non condensing. © Finisar Corporation April 7, 2006 Rev G Page 2 FTLF8519F2xCL 2x5 Pin SFF Product Specification – April 2006 III. Electrical Characteristics (TOP = 0 to 70 °C, VCC = 3.0 to 3.6 Volts) Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single ended data input swing Transmit Disable Voltage Transmit Enable Voltage Receiver Output differential impedance Single ended data output swing Data output rise/fall time Signal Detect Normal Signal Detect Fault Power Supply Rejection Total Jitter Contribution (p-p) Symbol Vcc Icc Min 3.0 Typ Rin Vin,pp VD VEN 80 250 2 Vee 100 Rout Vout,pp tr/ tf SD normal SD fault PSR RX Δ TJ 80 250 100 350 180 Vee Max 3.6 240 Unit V mA Ref. 120 1200 Vcc Vee+ 0.8 Ω mV V V 1 120 550 170 VccHOST Vee+0.5 100 123 Ω mV ps V V mVpp ps 1 3 4 5 5 6 7 2 Notes: 1. AC coupled. 2. Or open circuit. 3. Into 100 Ω differential termination. Data pattern is PRBS 27-1. 4. 20 – 80 %. 5. Signal detect is LVTTL. Logic 1 indicates normal operation; logic 0 indicates no signal detected. 6. All transceiver specifications are compliant with a power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the power supply filtering network shown on page 23 of the Small Form-factor Pluggable (SFP) Transceiver MultiSource Agreement (MSA), September 14, 20005. 7. If measured with TJ-free data input signal. In actual application, output TJ will be given by: TJ OUT = DJ IN + ΔDJ + (TJ IN − DJ IN ) + (ΔTJ − ΔDJ ) © Finisar Corporation April 7, 2006 Rev G 2 2 Page 3 FTLF8519F2xCL 2x5 Pin SFF Product Specification – April 2006 IV. Optical Characteristics (TOP = 0 to 70 °C, VCC = 3.0 to 3.6 Volts) Parameter Transmitter Output Opt. Pwr: 50 or 62.5 MMF Optical Wavelength Spectral Width Optical Modulation Amplitude Optical Rise/Fall Time Relative Intensity Noise Total Jitter Contribution (p-p) Extinction Ratio @ 1.25 Gb/s Receiver Receiver Sensitivity = 1.0625 Gb/s Receiver Sensitivity = 2.125 Gb/s Receiver Sensitivity = 1.25 Gb/s Stressed RX sens. = 1.0625 Gb/s Stressed RX sens. = 2.125 Gb/s Stressed RX sens = 1.25 Gb/s Average Received Power Receiver Elec. 3 dB cutoff freq. Optical Center Wavelength Return Loss Signal Detect Normal Signal Detect Fault Signal Detect Hysteresis Symbol Min POUT λ σ OMATx tr/ tf RIN TX Δ TJ ER -9 830 Typ Max Unit -3 860 0.85 dBm nm nm μW ps dB/Hz ps dB 196 150 -120 119 9 RxSENS RxSENS RxSENS -20 -18 -20 0.055 0.096 -13.5 0 1500 860 RxMAX λC RL SD normal SD fault 770 12 -20 -30 0.5 dBm dBm dBm mW mW dBm dBm MHz nm dB dBm dBm dB Ref. 1 2 3 4 5 5 6 7 7 8 Notes: 1. Class 1 Laser Safety per FDA/CDRH, EN (IEC) 60825 laser safety regulations. 2. Equivalent extinction ratio specification for Fibre Channel. Allows smaller ER at higher average power. 3. Unfiltered, 20-80%. Complies with FC 1x and 2x eye mask when filtered. 4. If measured with TJ-free data input signal. In actual application, output TJ will be given by: TJ OUT = DJ IN + ΔDJ + 5. 6. 7. 8. (TJ IN − DJ IN ) + (ΔTJ − ΔDJ ) 2 2 Specifications are for 50 micro-meter or 62.5 micro-meter fiber As measured with 9dB extinction ratio. Measured with conformance signals defined in FC-PI-2 10.0 specifications. Measured with conformance signals defined in IEEE 802.3 specifications. © Finisar Corporation April 7, 2006 Rev G Page 4 FTLF8519F2xCL 2x5 Pin SFF Product Specification – April 2006 V. General Specifications Parameter Data Rate Bit Error Rate Fiber Length on 50/125μm MMF Symbol BR Min Typ 1.062, 1.25 2.125 10-12 500 300 300 150 BER L L Fiber Length on 62.5/125μm MMF Max Units Gb/sec m m Ref. 1 4 2 3 2 3 Notes: 1. Gigabit Ethernet and 1x, 2x Fibre Channel compatible per IEEE 802.3 and FC-PI-2 10.0 respectively. 2. At 1.0625 Gb/s Fibre Channel and 1.25 Gb/s Gigabit Ethernet data rates. 3. At 2.125 Gb/s Fibre Channel data rate. 4. At 1.0625, 1.25, and 2.125Gb/s with PRBS 27-1. VI. Environmental Specifications FTLF8519F2xCL SFF transceivers have an operating temperature range from 0°C to +70°C case temperature. Parameter Case Operating Temperature Storage Temperature Symbol Top Tsto Min 0 -40 Typ Max 70 85 Units °C °C Ref. Notes: 1. SFF transceivers may be water washed. However, the process must be followed by a baking step at 80°C for one hour, to ensure the drying of any water which may be trapped inside then shells of the modules. VII. Regulatory Compliance Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations. These products are certified by TÜV and CSA to meet the Class 1 eye safety requirements of EN (IEC) 60825 and the electrical safety requirements of EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request. © Finisar Corporation April 7, 2006 Rev G Page 5 FTLF8519F2xCL 2x5 Pin SFF Product Specification – April 2006 VIII. Mechanical Specifications Finisar’s Small Form Factor (SFF) transceivers comply with the standard dimensions defined by the Small Form Factor Multi-Sourcing Agreement (MSA). FTLF8519F2GCL © Finisar Corporation April 7, 2006 Rev G Page 6 FTLF8519F2xCL 2x5 Pin SFF Product Specification – April 2006 FTLF8519F2KCL © Finisar Corporation April 7, 2006 Rev G Page 7 FTLF8519F2xCL 2x5 Pin SFF Product Specification – April 2006 FTLF8519F2HCL © Finisar Corporation April 7, 2006 Rev G Page 8 FTLF8519F2xCL 2x5 Pin SFF Product Specification – April 2006 IX. PCB Layout and Bezel Recommendations Minimum Recommended Pitch is 0.600” © Finisar Corporation April 7, 2006 Rev G Page 9 FTLF8519F2xCL 2x5 Pin SFF Product Specification – April 2006 X. References 1. Small Form Factor (SFF) Transceiver Multi-source Agreement (MSA). July 5, 2000. 2. IEEE Std 802.3, 2002 Edition, Clause 38, PMD Type 1000BASE-SX. IEEE Standards Department, 2002. 3. “Fibre Channel Draft Physical Interface Specification (FC-PI-2 10.0)”. American National Standard for Information Systems. 4. Directive 2002/95/EC of the European Council Parliament and of the Council, “on the restriction of the use of certain hazardous substances in electrical and electronic equipment.” January 27, 2003. 5. Small Form-factor Pluggable (SFP) Transceiver Multi-source Agreement (MSA), September 14, 2000. XI. For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 [email protected] www.finisar.com © Finisar Corporation April 7, 2006 Rev G Page 10