LM2622 600kHz/1.3MHz Step-up PWM DC/DC Converter General Description Features The LM2622 is a step-up DC/DC converter with a 1.6A, 0.2Ω internal switch and pin selectable operating frequency. With the ability to convert 3.3V to multiple outputs of 8V, -8V, and 23V, the LM2622 is an ideal part for biasing TFT displays. The LM2622 can be operated at switching frequencies of 600kHz and 1.3MHz allowing for easy filtering and low noise. An external compensation pin gives the user flexibility in setting frequency compensation, which makes possible the use of small, low ESR ceramic capacitors at the output. The LM2622 is available in a low profile 8-lead MSOP package. n n n n n 1.6A, 0.2Ω, internal switch Operating voltage as low as 2.0V 600kHz/1.3MHz pin selectable frequency operation Over temperature protection 8-Lead MSOP package Applications n n n n n TFT Bias Supplies Handheld Devices Portable Applications GSM/CDMA Phones Digital Cameras Typical Application Circuit 10127331 600 kHz Operation © 2004 National Semiconductor Corporation DS101273 www.national.com LM2622 600kHz/1.3MHz Step-up PWM DC/DC Converter May 2004 LM2622 Connection Diagram Top View 10127304 8-Lead Plastic MSOP NS Package Number MUA08A Ordering Information Order Number Package Type NSC Package Drawing Supplied As Package ID LM2622MM-ADJ MSOP-8 MUA08A 1000 Units, Tape and Reel S18B LM2622MMX-ADJ MSOP-8 MUA08A 3500 Units, Tape and Reel S18B Pin Description Pin Name Function 1 VC Compensation network connection. Connected to the output of the voltage error amplifier. 2 FB Output voltage feedback input. 3 SHDN 4 GND 5 SW Power switch input. Switch connected between SW pin and GND pin. 6 VIN Analog power input. 7 FSLCT 8 NC www.national.com Shutdown control input, active low. Analog and power ground. Switching frequency select input. VIN = 1.3MHz. Ground = 600kHz. Connect to ground or leave open. Connect to GND pin directly beneath the device if possible. If other traces are in the way or it is otherwise not possible to directly connect it to GND leave this pin open and shield it from sources of EMI. 2 LM2622 Block Diagram 10127303 3 www.national.com LM2622 Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Vapor Phase (60 sec.) 215˚C Infrared (15 sec.) 220˚C ESD Susceptibility (Note 3) VIN 12V Human Body Model SW Voltage 18V Machine Model FB Voltage 7V VC Voltage 7V SHDN Voltage 7V FSLCT Operating Conditions 12V Maximum Junction Temperature 150˚C Power Dissipation(Note 2) Operating Junction Temperature Range (Note 4) −40˚C to +125˚C Storage Temperature −65˚C to +150˚C Supply Voltage Internally Limited Lead Temperature 2kV 200V 2V to 12V 300˚C Electrical Characteristics Specifications in standard type face are for TJ = 25˚C and those with boldface type apply over the full Operating Temperature Range ( TJ = −40˚C to +125˚C)Unless otherwise specified. VIN =2.0V and IL = 0A, unless otherwise specified. Symbol Parameter Conditions IQ Quiescent Current VFB Feedback Voltage ICL(Note 6) Switch Current Limit VIN = 2.7V (Note 7) Min (Note 4) FB = 0V (Not Switching) VSHDN = 0V Units 1.3 2.0 mA 5 10 µA 1.26 1.2915 V 1.0 1.65 2.3 A ∆VO/∆ILOAD Load Regulation VIN = 3.3V Feedback Voltage Line Regulation 2.0V ≤ VIN ≤ 12.0V IB FB Pin Bias Current (Note 8) VIN Input Voltage Range 2 gm Error Amp Transconductance ∆I = 5µA 40 AV Error Amp Voltage Gain DMAX Maximum Duty Cycle fS Switching Frequency 6.7 0.013 0.5 78 FSLCT = Ground 135 mV/A 0.1 %/V 20 nA 12 V 290 µmho 135 V/V 85 % 480 600 720 kHz 1 1.25 1.5 MHz VSHDN = VIN 0.01 0.1 µA VSHDN = 0V −0.5 -1 FSLCT = VIN Shutdown Pin Current Max (Note 4) 1.2285 %VFB/∆VIN ISHDN Typ (Note 5) IL Switch Leakage Current VSW = 18V 0.01 3 µA RDSON Switch RDSON VIN = 2.7V, ISW = 1A 0.2 0.4 Ω ThSHDN SHDN Threshold Output High UVP 0.9 0.6 0.6 0.3 V On Threshold 1.8 1.92 2.0 V Off Threshold 1.7 1.82 1.9 V Output Low θJA Thermal Resistance Junction to Ambient(Note 9) 235 Junction to Ambient(Note 10) 225 Junction to Ambient(Note 11) 220 Junction to Ambient(Note 12) 200 Junction to Ambient(Note 13) 195 V ˚C/W Note 1: Absolute maximum ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions for which the device is intended to be functional, but device parameter specifications may not be guaranteed. For guaranteed specifications and test conditions, see the Electrical Characteristics. Note 2: The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction-to-ambient thermal resistance, θJA, and the ambient temperature, TA. See the Electrical Characteristics table for the thermal resistance of various layouts. The maximum allowable power dissipation at any ambient temperature is calculated using: PD (MAX) = (TJ(MAX) − TA)/θJA. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. Note 3: The human body model is a 100 pF capacitor discharged through a 1.5kΩ resistor into each pin. The machine model is a 200pF capacitor discharged directly into each pin. www.national.com 4 (Continued) Note 4: All limits guaranteed at room temperature (standard typeface) and at temperature extremes (bold typeface). All room temperature limits are 100% production tested. All limits at temperature extremes are guaranteed via correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL). Note 5: Typical numbers are at 25˚C and represent the most likely norm. Note 6: Duty cycle affects current limit due to ramp generator. Note 7: Current limit at 0% duty cycle. See TYPICAL PERFORMANCE section for Switch Current Limit vs. VIN Note 8: Bias current flows into FB pin. Note 9: Junction to ambient thermal resistance (no external heat sink) for the MSO8 package with minimal trace widths (0.010 inches) from the pins to the circuit. See "Scenario ’A’" in the Power Dissipation section. Note 10: Junction to ambient thermal resistance for the MSO8 package with minimal trace widths (0.010 inches) from the pins to the circuit and approximately 0.0191 sq. in. of copper heat sinking. See "Scenario ’B’" in the Power Dissipation section. Note 11: Junction to ambient thermal resistance for the MSO8 package with minimal trace widths (0.010 inches) from the pins to the circuit and approximately 0.0465 sq. in. of copper heat sinking. See "Scenario ’C’" in the Power Dissipation section. Note 12: Junction to ambient thermal resistance for the MSO8 package with minimal trace widths (0.010 inches) from the pins to the circuit and approximately 0.2523 sq. in. of copper heat sinking. See "Scenario ’D’" in the Power Dissipation section. Note 13: Junction to ambient thermal resistance for the MSO8 package with minimal trace widths (0.010 inches) from the pins to the circuit and approximately 0.0098 sq. in. of copper heat sinking on the top layer and 0.0760 sq. in. of copper heat sinking on the bottom layer, with three 0.020 in. vias connecting the planes. See "Scenario ’E’" in the Power Dissipation section. Typical Performance Characteristics Efficiency vs. Load Current (VOUT = 8V, fS = 1.3 MHz) Efficiency vs. Load Current (VOUT = 8V, fS = 600 kHz) 10127326 10127325 Switch Current Limit vs. Temperature (VIN = 3.3V, VOUT = 8V) Switch Current Limit vs. VIN 10127320 10127322 5 www.national.com LM2622 Electrical Characteristics LM2622 Typical Performance Characteristics (Continued) RDSON vs. VIN (ISW = 1A) IQ vs. VIN (600 kHz, not switching) 10127327 10127328 IQ vs. VIN (1.3 MHz, not switching) IQ vs. VIN (600 kHz, switching) 10127329 10127321 IQ vs. VIN (In shutdown) IQ vs. VIN (1.3 MHz, switching) 10127319 www.national.com 10127318 6 LM2622 Typical Performance Characteristics (Continued) Frequency vs. VIN (600 kHz) Frequency vs. VIN (1.3 MHz) 10127323 10127324 Load Transient Response (600 kHz operation) Load Transient Response (1.3 MHz operation) 10127317 10127316 Test circuit is shown in Figure 5 Test circuit is shown in Figure 4. 7 www.national.com LM2622 Operation 10127302 FIGURE 1. Simplified Boost Converter Diagram (a) First Cycle of Operation (b) Second Cycle Of Operation CONTINUOUS CONDUCTION MODE The LM2622 is a current-mode, PWM boost regulator. A boost regulator steps the input voltage up to a higher output voltage. In continuous conduction mode (when the inductor current never reaches zero at steady state), the boost regulator operates in two cycles. In the first cycle of operation, shown in Figure 1 (a), the transistor is closed and the diode is reverse biased. Energy is collected in the inductor and the load current is supplied by COUT. The second cycle is shown in Figure 1 (b). During this cycle, the transistor is open and the diode is forward biased. The energy stored in the inductor is transferred to the load and output capacitor. The ratio of these two cycles determines the output voltage. The output voltage is defined approximately as: INTRODUCTION TO COMPENSATION where D is the duty cycle of the switch, D and D' will be required for design calculations. SETTING THE OUTPUT VOLTAGE The output voltage is set using the feedback pin and a resistor divider connected to the output as shown in the typical operating circuit. The feedback pin voltage is 1.26V, so the ratio of the feedback resistors sets the output voltage according to the following equation: www.national.com 10127305 FIGURE 2. (a) Inductor current. (b) Diode current. 8 LM2622 Operation (Continued) The LM2622 is a current mode PWM boost converter. The signal flow of this control scheme has two feedback loops, one that senses switch current and one that senses output voltage. To keep a current programmed control converter stable above duty cycles of 50%, the inductor must meet certain criteria. The inductor, along with input and output voltage, will determine the slope of the current through the inductor (see Figure 2 (a)). If the slope of the inductor current is too great, the circuit will be unstable above duty cycles of 50%. A 10µH inductor is recommended for most 600 kHz applications, while a 4.7µH inductor may be used for most 1.25 MHz applications. If the duty cycle is approaching the maximum of 85%, it may be necessary to increase the inductance by as much as 2X. See Inductor and Diode Selection for more detailed inductor sizing. The LM2622 provides a compensation pin (VC) to customize the voltage loop feedback. It is recommended that a series combination of RC and CC be used for the compensation network, as shown in the typical application circuit. For any given application, there exists a unique combination of RC and CC that will optimize the performance of the LM2622 circuit in terms of its transient response. The series combination of RC and CC introduces a pole-zero pair according to the following equations: where fs is the switching frequency, D is the duty cycle, and RDSON is the ON resistance of the internal switch taken from the graph "RDSON vs. VIN" in the Typical Performance Characteristics section. This equation is only good for duty cycles greater than 50% (D > 0.5), for duty cycles less than 50% the recommended values may be used. The corresponding inductor current ripple as shown in Figure 2 (a) is given by: The inductor ripple current is important for a few reasons. One reason is because the peak switch current will be the average inductor current (input current or ILOAD/D’) plus ∆iL. As a side note, discontinuous operation occurs when the inductor current falls to zero during a switching cycle, or ∆iL is greater than the average inductor current. Therefore, continuous conduction mode occurs when ∆iL is less than the average inductor current. Care must be taken to make sure that the switch will not reach its current limit during normal operation. The inductor must also be sized accordingly. It should have a saturation current rating higher than the peak inductor current expected. The output voltage ripple is also affected by the total ripple current. The output diode for a boost regulator must be chosen correctly depending on the output voltage and the output current. The typical current waveform for the diode in continuous conduction mode is shown in Figure 2 (b). The diode must be rated for a reverse voltage equal to or greater than the output voltage used. The average current rating must be greater than the maximum load current expected, and the peak current rating must be greater than the peak inductor current. During short circuit testing, or if short circuit conditions are possible in the application, the diode current rating must exceed the switch current limit. Using Schottky diodes with lower forward voltage drop will decrease power dissipation and increase efficiency. where RO is the output impedance of the error amplifier, approximately 1MegΩ. For most applications, performance can be optimized by choosing values within the range 5kΩ ≤ RC ≤ 20kΩ (RC can be up to 200kΩ if CC2 is used, see High Output Capacitor ESR Compensation) and 680pF ≤ CC ≤ 4.7nF. Refer to the Applications Information section for recommended values for specific circuits and conditions. Refer to the Compensation section for other design requirement. COMPENSATION This section will present a general design procedure to help insure a stable and operational circuit. The designs in this datasheet are optimized for particular requirements. If different conversions are required, some of the components may need to be changed to ensure stability. Below is a set of general guidelines in designing a stable circuit for continuous conduction operation (loads greater than approximately 75mA), in most all cases this will provide for stability during discontinuous operation as well. The power components and their effects will be determined first, then the compensation components will be chosen to produce stability. DC GAIN AND OPEN-LOOP GAIN Since the control stage of the converter forms a complete feedback loop with the power components, it forms a closedloop system that must be stabilized to avoid positive feedback and instability. A value for open-loop DC gain will be required, from which you can calculate, or place, poles and zeros to determine the crossover frequency and the phase margin. A high phase margin (greater than 45˚) is desired for the best stability and transient response. For the purpose of stabilizing the LM2622, choosing a crossover point well below where the right half plane zero is located will ensure sufficient phase margin. A discussion of the right half plane zero and checking the crossover using the DC gain will follow. INDUCTOR AND DIODE SELECTION Although the inductor sizes mentioned earlier are fine for most applications, a more exact value can be calculated. To ensure stability at duty cycles above 50%, the inductor must have some minimum value determined by the minimum input voltage and the maximum output voltage. This equation is: INPUT AND OUTPUT CAPACITOR SELECTION The switching action of a boost regulator causes a triangular voltage waveform at the input. A capacitor is required to reduce the input ripple and noise for proper operation of the regulator. The size used is dependant on the application and board layout. If the regulator will be loaded uniformly, with 9 www.national.com LM2622 Operation given in the Introduction to Compensation section to set this pole in the area of 10Hz to 500Hz. The frequency of the pole created is determined by the equation: (Continued) very little load changes, and at lower current outputs, the input capacitor size can often be reduced. The size can also be reduced if the input of the regulator is very close to the source output. The size will generally need to be larger for applications where the regulator is supplying nearly the maximum rated output or if large load steps are expected. A minimum value of 10µF should be used for the less stressful condtions while a 22µF to 47µF capacitor may be required for higher power and dynamic loads. Larger values and/or lower ESR may be needed if the application requires very low ripple on the input source voltage. where RO is the output impedance of the error amplifier, approximately 1MegΩ. Since RC is generally much less than RO, it does not have much effect on the above equation and can be neglected until a value is chosen to set the zero fZC. fZC is created to cancel out the pole created by the output capacitor, fP1. The output capacitor pole will shift with different load currents as shown by the equation, so setting the zero is not exact. Determine the range of fP1 over the expected loads and then set the zero fZC to a point approximately in the middle. The frequency of this zero is determined by: The choice of output capacitors is also somewhat arbitrary and depends on the design requirements for output voltage ripple. It is recommended that low ESR (Equivalent Series Resistance, denoted RESR) capacitors be used such as ceramic, polymer electrolytic, or low ESR tantalum. Higher ESR capacitors may be used but will require more compensation which will be explained later on in the section. The ESR is also important because it determines the peak to peak output voltage ripple according to the approximate equation: ∆VOUT ) 2∆iLRESR (in Volts) A minimum value of 10µF is recommended and may be increased to a larger value. After choosing the output capacitor you can determine a pole-zero pair introduced into the control loop by the following equations: Now RC can be chosen with the selected value for CC. Check to make sure that the pole fPC is still in the 10Hz to 500Hz range, change each value slightly if needed to ensure both component values are in the recommended range. After checking the design at the end of this section, these values can be changed a little more to optimize performance if desired. This is best done in the lab on a bench, checking the load step response with different values until the ringing and overshoot on the output voltage at the edge of the load steps is minimal. This should produce a stable, high performance circuit. For improved transient response, higher values of RC should be chosen. This will improve the overall bandwidth which makes the regulator respond more quickly to transients. If more detail is required, or the most optimal performance is desired, refer to a more in depth discussion of compensating current mode DC/DC switching regulators. Where RL is the minimum load resistance corresponding to the maximum load current. The zero created by the ESR of the output capacitor is generally very high frequency if the ESR is small. If low ESR capacitors are used it can be neglected. If higher ESR capacitors are used see the High Output Capacitor ESR Compensation section. HIGH OUTPUT CAPACITOR ESR COMPENSATION When using an output capacitor with a high ESR value, or just to improve the overall phase margin of the control loop, another pole may be introduced to cancel the zero created by the ESR. This is accomplished by adding another capacitor, CC2, directly from the compensation pin VC to ground, in parallel with the series combination of RC and CC. The pole should be placed at the same frequency as fZ1, the ESR zero. The equation for this pole follows: RIGHT HALF PLANE ZERO A current mode control boost regulator has an inherent right half plane zero (RHP zero). This zero has the effect of a zero in the gain plot, causing an imposed +20dB/decade on the rolloff, but has the effect of a pole in the phase, subtracting another 90˚ in the phase plot. This can cause undesirable effects if the control loop is influenced by this zero. To ensure the RHP zero does not cause instability issues, the control loop should be designed to have a bandwidth of less than 1⁄2 the frequency of the RHP zero. This zero occurs at a frequency of: To ensure this equation is valid, and that CC2 can be used without negatively impacting the effects of RC and CC, fPC2 must be greater than 10fZC. CHECKING THE DESIGN The final step is to check the design. This is to ensure a bandwidth of 1⁄2 or less of the frequency of the RHP zero. This is done by calculating the open-loop DC gain, ADC. After this value is known, you can calculate the crossover visually by placing a −20dB/decade slope at each pole, and a +20dB/ decade slope for each zero. The point at which the gain plot crosses unity gain, or 0dB, is the crossover frequency. If the crossover frequency is less than 1⁄2 the RHP zero, the phase margin should be high enough for stability. The phase mar- where ILOAD is the maximum load current. SELECTING THE COMPENSATION COMPONENTS The first step in selecting the compensation components RC and CC is to set a dominant low frequency pole in the control loop. Simply choose values for RC and CC within the ranges www.national.com 10 where RL is the minimum load resistance, VIN is the minimum input voltage, gm is the error amplifier transconductance found in the Electrical Characteristics table, and RDSON is the value chosen from the graph "RDSON vs. VIN " in the Typical Performance Characteristics section. (Continued) gin can also be improved by adding CC2 as discussed earlier in the section. The equation for ADC is given below with additional equations required for the calculation: LAYOUT CONSIDERATIONS The input bypass capacitor CIN, as shown in the typical operating circuit, must be placed close to the IC. This will reduce copper trace resistance which effects input voltage ripple of the IC. For additional input voltage filtering, a 100nF bypass capacitor can be placed in parallel with CIN, close to the VIN pin, to shunt any high frequency noise to ground. The output capacitor, COUT, should also be placed close to the IC. Any copper trace connections for the COUT capacitor can increase the series resistance, which directly effects output voltage ripple. The feedback network, resistors RFB1 and RFB2, should be kept close to the FB pin, and away from the inductor, to minimize copper trace connections that can inject noise into the system. Trace connections made to the inductor and schottky diode should be minimized to reduce power dissipation and increase overall efficiency. For more detail on switching power supply layout considerations see Application Note AN-1149: Layout Guidelines for Switching Power Supplies. mc ) 0.072fs (in V/s) 11 www.national.com LM2622 Operation LM2622 Application Information 10127308 FIGURE 3. Triple Output TFT Bias (600 kHz operation) TRIPLE OUTPUT TFT BIAS The circuit in Figure 3 shows how the LM2622 can be configured to provide outputs of 8V, −8V, and 23V, convenient for biasing TFT displays. The 8V output is regulated, while the −8V and 23V outputs are unregulated. The 8V output is generated by a typical boost topology. The basic operation of the boost converter is described in the OPERATION section. The output voltage is set with RFB1 and RFB2 by: mended to insure the converter is stable at duty cycles greater than 50%. Refer to the COMPENSATION section for more information. The -8V output is derived from a diode inverter. During the second cycle, when the transistor is open, D2 conducts and C1 charges to 8V minus a diode drop ()0.4V if using a Schottky). When the transistor opens in the first cycle, D3 conducts and C1’s polarity is reversed with respect to the output at C2, producing -8V. The 23V output is realized with a series of capacitor charge pumps. It consists of four stages: the first stage includes C4, D4, and the LM2622 switch; the second stage uses C5, D5, and D1; the third stage includes C6, D6, and the LM2622 switch; the final stage is C7 and D7. In the first stage, C4 charges to 8V when the LM2622 switch is closed, which causes D5 to conduct when the switch is open. In the second stage, the voltage across C5 is VC4 + VD1 - VD5 = VC4 ) 8V when the switch is open. However, because C5 is referenced to the 8V output, the voltage at C5 is 16V when CFB is placed across RFB1 to act as a pseudo soft-start. The compensation network of RC and CC are chosen to optimally stabilize the converter. The inductor also affects the stability. When operating at 600 kHz, a 10uH inductor is recom- www.national.com 12 (Continued) referenced to ground. In the third stage, the 16V at C5 appears across C6 when the switch is closed. When the switch opens, C6 is referenced to the 8V output minus a diode drop, which raises the voltage at C6 with respect to ground to about 24V. Hence, in the fourth stage, C7 is charged to 24V when the switch is open. From the first stage to the last, there are three diode drops that make the output voltage closer to 24 - 3xVDIODE (about 22.8V if a 0.4V forward drop is assumed). TABLE 1. Components For Circuits in Figure 3 Component 600 kHz 1.3 MHz L 10µH 4.7µH COUT1 10µF 22µF COUT2 10µF NOT USED CC 3.9nF 1.5nF CFB1 0.1µF 15nF CFB2 NOT USED 560pF CIN 10µF 22µF C1 4.7µF 4.7µF Component 600 kHz C2 0.1µF 0.1µF C4 1µF 1µF C5 1µF 1µF C6 1µF 1µF C7 1µF 1µF RFB1 40.2kΩ 91kΩ RFB2 7.5kΩ 18kΩ RC 5.1kΩ 10kΩ D1 MBRM140T3 MBRM140T3 BAT54S BAT54S BAT54S BAT54S BAT54S BAT54S D2 D3 D4 D5 D6 D7 1.3 MHz 600 KHZ OPERATION 10127331 FIGURE 4. 600 kHz operation 13 www.national.com LM2622 Application Information LM2622 Application Information 1.3 MHZ OPERATION (Continued) 10127330 FIGURE 5. 1.3 MHz operation POWER DISSIPATION The output power of the LM2622 is limited by its maximum power dissipation. The maximum power dissipation is determined by the formula PD = (Tjmax - TA)/θJA where Tjmax is the maximum specidfied junction temperature (125˚C), TA is the ambient temperature, and θJA is the thermal resistance of the package. θJA is dependant on the layout of the board as shown below. 10127312 10127311 10127313 www.national.com 14 LM2622 Application Information (Continued) 10127315 10127314 15 www.national.com LM2622 600kHz/1.3MHz Step-up PWM DC/DC Converter Physical Dimensions inches (millimeters) unless otherwise noted LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: [email protected] National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.