EPCOS B41252B4339M000 Aluminum electrolytic capacitor Datasheet

Aluminum electrolytic capacitors
Snap-in capacitors
Series/Type:
B41252
Date:
November 2008
© EPCOS AG 2008. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
Snap-in capacitors
B41252
Standard series 105 °C
General-purpose grade capacitors
Applications
Switch-mode power supplies in industrial and entertainment
electronics
Features
High ripple current capability
RoHS-compatible
Useful life of 2000 h at 105 °C
Construction
Aluminum case, fully insulated
Snap-in solder pins to hold component in place on PC-board
Minus pole marking on the insulating sleeve
Case with safety vent
Please read Cautions and warnings and
Important notes at the end of this document.
Page 2 of 19
B41252
Standard series 105 °C
Specifications and characteristics in brief
Rated voltage VR
Surge voltage VS
Rated capacitance CR
Capacitance tolerance
Dissipation factor (max.)
(20 °C, 120 Hz)
10 ... 100 V DC
1.15 VR
820 ... 56000 µF
±20% M
VR (V DC)
tan δ
10 16 25 35 50 63 80 100
0.45 0.35 0.30 0.20 0.20 0.15 0.12 0.12
Leakage current Ileak
(20 °C, after 5 minutes)
Useful life
85 °C; VR; IAC,R
2000 h
Shelf life
Operating temperature
range
Characteristics at low
temperature
Sectional specification
Requirements:
∆C/C
≤ 20% of initial value
tan δ
≤ 2 times initial specified limit
Ileak
≤ initial specified limit
After storage for 1000 h at 105 °C, the capacitors shall meet the
requirement of load life test after reforming process. After test: VR to be
applied for 30 minutes, 24 to 48 hours before measurement.
40 °C ... +105 °C
Max. impedance ratio at 120 Hz
VR
≤ 16 V 25 V
Z -25 °C / Z 20 °C
4
3
Z -40 °C / Z 20 °C
15
10
IEC 60384-4
Please read Cautions and warnings and
Important notes at the end of this document.
Page 3 of 19
35 V
3
8
50 ... 63 V ≥ 80 V
2
2
6
5
B41252
Standard series 105 °C
Dimensional drawing
* = Shorter terminal (4.5 1) mm is also available upon request.
Dimensions (mm)
d +1
l ±2
22
25
22
30
22
35
22
40
22
45
22
50
25.4
25
25.4
30
25.4
35
25.4
40
25.4
45
25.4
50
Approx.
weight (g)
Packing
units (pcs.)
13.0
15.0
20.5
23.0
25.0
29.5
13.5
19.5
25.0
28.0
31.0
39.0
200
100
100
100
100
100
100
50
50
50
50
50
Please read Cautions and warnings and
Important notes at the end of this document.
Dimensions (mm)
d +1
l ±2
30
25
30
30
30
35
30
40
30
45
30
50
35
30
35
35
35
40
35
45
35
50
Page 4 of 19
Approx.
weight (g)
Packing
units (pcs.)
24.5
25.5
32.5
39.0
43.5
55.5
43.0
50.5
52.0
65.0
70.5
100
100
50
50
50
50
80
50
50
50
50
B41252
Standard series 105 °C
Overview of available types
VR (V DC)
10
16
25
35
50
63
80
100
22
× 25 22 × 30
25.4 × 25
Case dimensions d × l (mm)
CR (µF)
820
22 × 30 22 × 35
25.4 × 25 25.4 × 30
1000
× 25 22 × 30 22 × 40
25.4 × 25 25.4 × 35
30 × 25
1200
22
1500
22 × 30 22 × 35 22 × 45
25.4 × 25 25.4 × 30 25.4 × 40
30 × 30
1800
22 × 30 22 × 40 25.4 × 45
25.4 × 25 25.4 × 35 30 × 35
30 × 25
2200
22 × 35 22 × 45 25.4 × 50
25.4 × 30 25.4 × 35 30 × 40
30 × 30 35 × 30
2700
22
× 30 22 × 40 25.4 × 45 30
25.4 × 30 30 × 35 35
30 × 25
× 45
× 35
× 35 22 × 50 25.4 × 50 30
25.4 × 40 30 × 40 35
30 × 30 35 × 30
× 50
× 40
3300
22
× 25 22
3900
22
× 30 22 × 40 25.4 × 45 30
25.4 × 35 30 × 35 35
30 × 25
× 45 35
× 35
× 45
× 50
4700
22
× 25 22 × 35 22 × 45 25.4 × 50 30
25.4 × 25 25.4 × 40 30 × 40 35
30 × 30 35 × 30
× 50 35
× 40
5600
22
× 30 22 × 35 22 × 50 30
25.4 × 30 25.4 × 40 35
30 × 25 30 × 35
× 45 35
× 35
× 45
6800
22
× 30 22 × 40 25.4 × 50 30
25.4 × 35 30 × 40 35
30 × 30 35 × 30
× 50 35
× 40
× 50
8200
22
× 25 22 × 35 22 × 50 30
25.4 × 30 25.4 × 40 35
30 × 30
Please read Cautions and warnings and
Important notes at the end of this document.
Page 5 of 19
× 45 35
× 35
× 45
B41252
Standard series 105 °C
VR (V DC)
10
16
25
35
50
63
80
100
Case dimensions d × l (mm)
CR (µF)
10000
22
× 25 22 × 30 22 × 40 25.4 × 45 30
25.4 × 25 25.4 × 35 30 × 35 35
× 50 35
× 40
12000
22
× 30 22 × 35 22 × 45 25.4 × 50 35
25.4 × 30 25.4 × 40 30 × 40
30 × 25 30 × 30 35 × 30
× 45
15000
22 × 35 22 × 40 25.4 × 45 30
25.4 × 25 25.4 × 35 30 × 35 35
30 × 30 35 × 30
× 45 35
× 35
18000
22 × 35 22 × 45 25.4 × 50 35
25.4 × 30 25.4 × 40 30 × 40
30 × 30 35 × 35
× 40
22000
22 × 40 25.4 × 45 30
25.4 × 35 30 × 35 35
30 × 25
× 45 35
× 35
× 45
27000
22 × 50 25.4 × 50 35
25.4 × 40 30 × 40
30 × 30 35 × 30
× 45
33000
25.4 × 45 30
30 × 35 35
× 45
× 35
39000
25.4 × 50 30
30 × 40 35
35 × 30
× 50
× 40
47000
30
35
× 45 35
× 35
× 45
56000
35
× 45
× 50
× 50
The capacitance and voltage ratings listed above are available in different cases upon request.
Other voltage and capacitance ratings are also available upon request.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 6 of 19
B41252
Standard series 105 °C
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
VR = 10 V DC
10000
22 × 25
12000
22 × 30
15000
22 × 35
15000
25.4 × 25
18000
22 × 35
18000
25.4 × 30
22000
22 × 40
22000
25.4 × 35
22000
30 × 25
27000
22 × 50
27000
25.4 × 40
27000
30 × 30
33000
25.4 × 45
33000
30 × 35
39000
25.4 × 50
39000
30 × 40
39000
35 × 30
47000
30 × 45
47000
35 × 35
56000
35 × 45
VR = 16 V DC
8200
22 × 25
10000
22 × 30
10000
25.4 × 25
12000
22 × 35
12000
25.4 × 30
12000
30 × 25
15000
22 × 40
15000
25.4 × 35
15000
30 × 30
18000
22 × 45
18000
25.4 × 40
18000
30 × 30
22000
25.4 × 45
22000
30 × 35
tan δmax
120 Hz
20 °C
IAC,max
120 Hz
60 °C
A
IAC,max
120 Hz
85 °C
A
IAC,R
120 Hz
105 °C
A
Ordering code
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
4.99
5.70
6.51
6.33
6.90
7.15
7.71
8.00
7.77
8.92
8.90
8.72
9.80
9.66
10.58
10.51
10.26
11.39
11.20
12.63
3.80
4.34
4.95
4.81
5.25
5.44
5.86
6.09
5.92
6.79
6.77
6.63
7.46
7.35
8.05
8.00
7.81
8.66
8.52
9.61
2.17
2.48
2.83
2.75
3.00
3.11
3.35
3.48
3.38
3.88
3.87
3.79
4.26
4.20
4.60
4.57
4.46
4.95
4.87
5.49
B41252A3109M000
B41252A3129M000
B41252A3159M000
B41252B3159M000
B41252A3189M000
B41252B3189M000
B41252A3229M000
B41252B3229M000
B41252C3229M000
B41252A3279M000
B41252B3279M000
B41252C3279M000
B41252A3339M000
B41252B3339M000
B41252A3399M000
B41252B3399M000
B41252C3399M000
B41252A3479M000
B41252B3479M000
B41252A3569M000
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
4.92
5.70
5.89
6.44
6.67
6.83
7.29
7.57
7.77
8.05
8.40
8.21
9.27
9.15
3.75
4.34
4.48
4.90
5.08
5.20
5.55
5.76
5.92
6.13
6.39
6.25
7.05
6.97
2.14
2.48
2.56
2.80
2.90
2.97
3.17
3.29
3.38
3.50
3.65
3.57
4.03
3.98
B41252A4828M000
B41252A4109M000
B41252B4109M000
B41252A4129M000
B41252B4129M000
B41252C4129M000
B41252A4159M000
B41252B4159M000
B41252C4159M000
B41252A4189M000
B41252B4189M000
B41252C4189M000
B41252A4229M000
B41252B4229M000
Please read Cautions and warnings and
Important notes at the end of this document.
Page 7 of 19
B41252
Standard series 105 °C
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
VR = 16 V DC
27000
25.4 × 50
27000
30 × 40
27000
35 × 30
33000
30 × 45
33000
35 × 35
39000
30 × 50
39000
35 × 40
47000
35 × 45
VR = 25 V DC
4700
22 × 25
5600
22 × 30
6800
22 × 30
8200
22 × 35
8200
25.4 × 30
10000
22 × 40
10000
25.4 × 35
12000
22 × 45
12000
25.4 × 40
12000
30 × 30
15000
25.4 × 45
15000
30 × 35
15000
35 × 30
18000
25.4 × 50
18000
30 × 40
18000
35 × 35
22000
30 × 45
22000
35 × 35
27000
35 × 45
VR = 35 V DC
3300
22 × 25
3900
22 × 30
4700
22 × 35
4700
25.4 × 25
5600
22 × 35
5600
25.4 × 30
5600
30 × 25
tan δmax
120 Hz
20 °C
IAC,max
120 Hz
60 °C
A
IAC,max
120 Hz
85 °C
A
IAC,R
120 Hz
105 °C
A
Ordering code
0.35
0.35
0.35
0.35
0.35
0.35
0.35
0.35
10.17
10.10
9.87
11.02
10.83
11.87
11.73
12.65
7.74
7.68
7.51
8.38
8.24
9.03
8.93
9.63
4.42
4.39
4.29
4.79
4.71
5.16
5.10
5.50
B41252A4279M000
B41252B4279M000
B41252C4279M000
B41252A4339M000
B41252B4339M000
B41252A4399M000
B41252B4399M000
B41252A4479M000
0.30
0.30
0.30
0.30
0.30
0.30
0.30
0.30
0.30
0.30
0.30
0.30
0.30
0.30
0.30
0.30
0.30
0.30
0.30
3.98
4.55
4.92
5.57
5.75
6.37
6.62
7.11
7.41
7.25
8.33
8.21
8.40
9.15
9.09
9.34
10.03
9.84
11.32
3.03
3.47
3.75
4.24
4.38
4.85
5.04
5.41
5.64
5.51
6.34
6.25
6.39
6.97
6.91
7.11
7.63
7.49
8.61
1.73
1.98
2.14
2.42
2.50
2.77
2.88
3.09
3.22
3.15
3.62
3.57
3.65
3.98
3.95
4.06
4.36
4.28
4.29
B41252A5478M000
B41252A5568M000
B41252A5688M000
B41252A5828M000
B41252B5828M000
B41252A5109M000
B41252B5109M000
B41252A5129M000
B41252B5129M000
B41252C5129M000
B41252A5159M000
B41252B5159M000
B41252C5159M000
B41252A5189M000
B41252B5189M000
B41252C5189M000
B41252A5229M000
B41252B5229M000
B41252A5279M000
0.20
0.20
0.20
0.20
0.20
0.20
0.20
2.90
4.32
4.92
4.81
5.27
5.45
5.59
2.21
3.29
3.75
3.66
4.01
4.15
4.25
1.26
1.88
2.14
2.09
2.29
2.37
2.43
B41252A7338M000
B41252B7398M000
B41252A7478M000
B41252B7478M000
B41252A7568M000
B41252B7568M000
B41252C7568M000
Please read Cautions and warnings and
Important notes at the end of this document.
Page 8 of 19
B41252
Standard series 105 °C
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
VR = 35 V DC
6800
22 × 40
6800
25.4 × 35
6800
30 × 30
8200
22 × 50
8200
25.4 × 40
8200
30 × 30
10000
25.4 × 45
10000
30 × 35
12000
25.4 × 50
12000
30 × 40
12000
35 × 30
15000
30 × 45
15000
35 × 35
18000
35 × 40
22000
35 × 45
VR = 50 V DC
2700
22 × 30
3300
22 × 35
3900
22 × 40
3900
25.4 × 35
3900
30 × 25
4700
22 × 45
4700
25.4 × 40
4700
30 × 30
5600
22 × 50
5600
25.4 × 40
5600
30 × 35
6800
25.4 × 50
6800
30 × 40
6800
35 × 30
8200
30 × 45
8200
35 × 35
10000
30 × 50
10000
35 × 40
12000
35 × 45
15000
35 × 50
tan δmax
120 Hz
20 °C
IAC,max
120 Hz
60 °C
A
IAC,max
120 Hz
85 °C
A
IAC,R
120 Hz
105 °C
A
Ordering code
0.20
0.20
0.20
0.20
0.20
0.20
0.20
0.20
0.20
0.20
0.20
0.20
0.20
0.20
0.20
6.00
6.23
6.42
6.95
6.95
6.79
7.89
7.77
8.69
8.63
8.44
9.64
9.48
10.40
11.39
4.57
4.74
4.88
5.29
5.29
5.16
6.00
5.92
6.62
6.56
6.42
7.33
7.21
7.91
8.66
2.61
2.71
2.79
3.02
3.02
2.95
3.43
3.38
3.78
3.75
3.67
4.19
4.12
4.52
4.95
B41252A7688M000
B41252B7688M000
B41252C7688M000
B41252A7828M000
B41252B7828M000
B41252C7828M000
B41252A7109M000
B41252B7109M000
B41252A7129M000
B41252B7129M000
B41252C7129M000
B41252A7159M000
B41252B7159M000
B41252A7189M000
B41252A7229M000
0.20
0.20
0.20
0.20
0.20
0.20
0.20
0.20
0.20
0.20
0.20
0.20
0.20
0.20
0.20
0.20
0.20
0.20
0.20
0.20
4.46
5.06
5.80
6.03
5.84
6.46
6.74
6.60
7.15
7.15
7.38
8.37
8.30
8.12
9.06
8.90
10.17
10.05
10.99
12.05
3.40
3.85
4.41
4.59
4.45
4.92
5.13
5.02
5.44
5.44
5.62
6.37
6.32
6.18
6.90
6.77
7.74
7.65
8.37
9.17
1.94
2.20
2.52
2.62
2.54
2.81
2.93
2.87
3.11
3.11
3.21
3.64
3.61
3.53
3.94
3.87
4.42
4.37
4.78
5.24
B41252A6278M000
B41252A6338M000
B41252A6398M000
B41252B6398M000
B41252C6398M000
B41252A6478M000
B41252B6478M000
B41252C6478M000
B41252A6568M000
B41252B6568M000
B41252C6568M000
B41252A6688M000
B41252B6688M000
B41252C6688M000
B41252A6828M000
B41252B6828M000
B41252A6109M000
B41252B6109M000
B41252A6129M000
B41252A6159M000
Please read Cautions and warnings and
Important notes at the end of this document.
Page 9 of 19
B41252
Standard series 105 °C
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
VR = 63 V DC
1200
22 × 25
1500
22 × 30
1500
25.4 × 25
1800
22 × 30
1800
25.4 × 25
2200
22 × 35
2200
25.4 × 30
2700
22 × 40
2700
25.4 × 30
2700
30 × 25
3300
22 × 50
3300
25.4 × 40
3300
30 × 30
3900
25.4 × 45
3900
30 × 35
4700
25.4 × 50
4700
30 × 40
4700
35 × 30
5600
30 × 45
5600
35 × 35
6800
30 × 50
6800
35 × 40
8200
35 × 45
10000
35 × 50
VR = 80 V DC
820
22 × 25
1000
22 × 30
1000
25.4 × 25
1200
22 × 30
1200
25.4 × 25
1500
22 × 35
1500
25.4 × 30
1800
22 × 40
1800
25.4 × 35
1800
30 × 25
2200
22 × 45
2200
25.4 × 35
2200
30 × 30
tan δmax
120 Hz
20 °C
IAC,max
120 Hz
60 °C
A
IAC,max
120 Hz
85 °C
A
IAC,R
120 Hz
105 °C
A
Ordering code
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
3.15
3.45
3.54
3.77
3.89
4.28
4.42
4.99
4.90
5.01
5.82
5.82
5.70
6.62
6.53
7.36
7.29
7.13
8.07
7.96
9.02
8.92
9.71
10.90
2.40
2.63
2.70
2.87
2.96
3.26
3.36
3.80
3.73
3.82
4.43
4.43
4.34
5.04
4.97
5.60
5.55
5.43
6.14
6.06
6.86
6.79
7.39
8.30
1.37
1.50
1.54
1.64
1.69
1.86
1.92
2.17
2.13
2.18
2.53
2.53
2.48
2.88
2.84
3.20
3.17
3.10
3.51
3.46
3.92
3.88
4.22
4.74
B41252A8128M000
B41252A8158M000
B41252B8158M000
B41252A8188M000
B41252B8188M000
B41252A8228M000
B41252B8228M000
B41252A8278M000
B41252B8278M000
B41252C8278M000
B41252A8338M000
B41252B8338M000
B41252C8338M000
B41252A8398M000
B41252B8398M000
B41252A8478M000
B41252B8478M000
B41252C8478M000
B41252A8568M000
B41252B8568M000
B41252A8688M000
B41252B8688M000
B41252A8828M000
B41252A8109M000
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
3.15
3.73
3.84
3.84
3.96
4.55
4.72
5.24
5.45
5.29
5.77
5.73
5.89
2.40
2.84
2.92
2.92
3.01
3.47
3.59
3.99
4.15
4.03
4.39
4.36
4.48
1.37
1.62
1.67
1.67
1.72
1.98
2.05
2.28
2.37
2.30
2.51
2.49
2.56
B41252A0827M000
B41252A0108M000
B41252B0108M000
B41252A0128M000
B41252B0128M000
B41252A0158M000
B41252B0158M000
B41252A0188M000
B41252B0188M000
B41252C0188M000
B41252A0228M000
B41252B0228M000
B41252C0228M000
Please read Cautions and warnings and
Important notes at the end of this document.
Page 10 of 19
B41252
Standard series 105 °C
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
VR = 80 V DC
2700
25.4 × 45
2700
30 × 35
3300
25.4 × 50
3300
30 × 40
3300
35 × 30
3900
30 × 45
3900
35 × 35
4700
30 × 50
4700
35 × 40
5600
35 × 45
6800
35 × 50
VR = 100 V DC
820
22 × 30
820
25.4 × 25
1000
22 × 35
1000
25.4 × 30
1200
22 × 40
1200
25.4 × 35
1200
30 × 25
1500
22 × 45
1500
25.4 × 40
1500
30 × 30
1800
25.4 × 45
1800
30 × 35
2200
25.4 × 50
2200
30 × 40
2200
35 × 30
2700
30 × 45
2700
35 × 35
3300
30 × 50
3300
35 × 40
3900
35 × 45
4700
35 × 50
tan δmax
120 Hz
20 °C
IAC,max
120 Hz
60 °C
A
IAC,max
120 Hz
85 °C
A
IAC,R
120 Hz
105 °C
A
Ordering code
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
6.97
6.88
7.66
7.59
7.43
8.63
8.49
9.43
9.34
10.21
11.27
5.30
5.23
5.83
5.78
5.65
6.56
6.46
7.18
7.11
7.77
8.58
3.03
2.99
3.33
3.30
3.23
3.75
3.69
4.10
4.06
4.44
4.90
B41252A0278M000
B41252B0278M000
B41252A0338M000
B41252B0338M000
B41252C0338M000
B41252A0398M000
B41252B0398M000
B41252A0478M000
B41252B0478M000
B41252A0568M000
B41252A0688M000
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
3.36
3.47
3.93
4.07
4.28
4.46
4.32
5.01
5.24
5.13
6.00
5.91
6.56
6.51
6.35
7.52
7.41
8.26
8.17
9.27
10.12
2.56
2.64
2.99
3.10
3.26
3.40
3.29
3.82
3.99
3.90
4.57
4.50
4.99
4.95
4.83
5.72
5.64
6.28
6.21
7.05
7.70
1.46
1.51
1.71
1.77
1.86
1.94
1.88
2.18
2.28
2.23
2.61
2.57
2.85
2.83
2.76
3.27
3.22
3.59
3.55
4.03
4.40
B41252A9827M000
B41252B9827M000
B41252A9108M000
B41252B9108M000
B41252A9128M000
B41252B9128M000
B41252C9128M000
B41252A9158M000
B41252B9158M000
B41252C9158M000
B41252A9188M000
B41252B9188M000
B41252A9228M000
B41252B9228M000
B41252C9228M000
B41252A9278M000
B41252B9278M000
B41252A9338M000
B41252B9338M000
B41252A9398M000
B41252A9478M000
Please read Cautions and warnings and
Important notes at the end of this document.
Page 11 of 19
B41252
Standard series 105 °C
Useful life
depending on ambient temperature TA under ripple current operating conditions1)
Frequency factor of permissible ripple
current IAC versus frequency f
Frequency characteristics of ESR
Typical behavior
1) Refer to chapter "General technical information, 5.3 Calculation of useful life" for an explanation on how to interpret the useful life
graphs.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 12 of 19
B41252
Standard series 105 °C
Impedance Z versus frequency f
Typical behavior at 20 °C
Please read Cautions and warnings and
Important notes at the end of this document.
Page 13 of 19
B41252
Standard series 105 °C
Cautions and warnings
Personal safety
The electrolytes used by EPCOS have not only been optimized with a view to the intended
application, but also with regard to health and environmental compatibility. They do not contain
any solvents that are detrimental to health, e.g. dimethyl formamide (DMF) or dimethyl acetamide
(DMAC).
Furthermore, part of the high-voltage electrolytes used by EPCOS are self-extinguishing. They
contain flame-retarding substances which will quickly extinguish any flame that may have been
ignited.
As far as possible, EPCOS does not use any dangerous chemicals or compounds to produce
operating electrolytes. However, in exceptional cases, such materials must be used in order to
achieve specific physical and electrical properties because no safe substitute materials are
currently known. However, the amount of dangerous materials used in our products has been
limited to an absolute minimum. Nevertheless, the following rules should be observed when
handling Al electrolytic capacitors:
Any escaping electrolyte should not come into contact with eyes or skin.
If electrolyte does come into contact with the skin, wash the affected parts immediately with
running water. If the eyes are affected, rinse them for 10 minutes with plenty of water. If
symptoms persist, seek medical treatment.
Avoid breathing in electrolyte vapor or mists. Workplaces and other affected areas should be
well ventilated. Clothing that has been contaminated by electrolyte must be changed and
rinsed in water.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 14 of 19
B41252
Standard series 105 °C
Product safety
The table below summarize the safety instructions that must be observed without fail. A detailed
description can be found in the relevant sections of chapter "General technical information".
Topic
Safety information
Polarity
Make sure that polar capacitors are connected
with the right polarity.
Reverse voltage
Voltages polarity classes should be prevented by
connecting a diode.
Do not exceed the upper category temperatur.
Upper category
temperature
Maintenance
Mounting
position of screw
terminal capacitors
Mounting of
single-ended
capacitors
Robustness of
terminals
Soldering
Make periodic inspections of the capacitors.
Before the inspection, make sure that the power
supply is turned off and carefully discharge the
electricity of the capacitors.
Do not apply any mechanical stress to the
capacitor terminals.
Do not mount the capacitor with the terminals
(safety vent) upside down.
Reference
Chapter "General
technical information"
1
"Basic construction of
aluminum electrolytic
capacitors"
3.1.6
"Reverse voltage"
7.2
"Maximum permissible
operating temperature"
10
"Maintenance"
11.1
"Mounting positions of
capacitors with screw
terminals"
The internal structure of single-ended capacitors 11.4
might be damaged if excessive force is applied to "Mounting
the lead wires.
considerations for
Avoid any compressive, tensile or flexural stress. single-ended capacitors"
Do not move the capacitor after soldering to PC
board.
Do not pick up the PC board by the soldered
capacitor.
Do not insert the capacitor on the PC board with a
hole space different to the lead space specified.
The following maximum tightening torques must
11.3
not be exceeded when connecting screw
"Mounting torques"
terminals:
M5: 2 Nm
M6: 2.5 Nm
Do not exceed the specified time or temperature 11.5
limits during soldering.
"Soldering"
Please read Cautions and warnings and
Important notes at the end of this document.
Page 15 of 19
B41252
Standard series 105 °C
Topic
Soldering,
cleaning agents
Passive
flammability
Active
flammability
Safety information
Reference
Chapter "General
technical information"
Do not allow halogenated hydrocarbons to come 11.6
into contact with aluminum electrolytic capacitors. "Cleaning agents"
Avoid external energy, such as fire or electricity.
8.1
"Passive flammability"
Avoid overload of the capacitors.
8.2
"Active flammability"
Breakdown strength Do not damage the insulating sleeve, especially
of insulating
when ring clips are used for mounting.
sleeves
Please read Cautions and warnings and
Important notes at the end of this document.
Page 16 of 19
Reference
Chapter "Capacitors
with screw terminals"
"Screw terminals accessories"
B41252
Standard series 105 °C
Symbols and terms
Symbol
English
German
C
CR
CS
CS,T
Cf
d
dmax
ESL
ESR
ESRf
Capacitance
Rated capacitance
Series capacitance
Series capacitance at temperature T
Capacitance at frequency f
Case diameter, nominal dimension
Maximum case diameter
Self-inductance
Equivalent series resistance
Equivalent series resistance at
frequency f
Equivalent series resistance at
temperature T
Frequency
Current
Alternating current (ripple current)
Root-mean-square value of alternating
current
Ripple current at frequency f
Maximum permissible ripple current
Rated ripple current
Rated ripple current for base cooling
Leakage current
Operating leakage current
Case length, nominal dimension
Maximum case length (without
terminals and mounting stud)
Resistance
Insulation resistance
Balancing resistance
Temperature
Temperature difference
Ambient temperature
Case temperature
Capacitor base temperature
Time
Period
Service life (operating hours)
Kapazität
Nennkapazität
Serienkapazität
Serienkapazität bei Temperatur T
Kapazität bei Frequenz f
Gehäusedurchmesser, Nennmaß
Maximaler Gehäusedurchmesser
Eigeninduktivität
Ersatzserienwiderstand
Ersatzserienwiderstand bei Frequenz f
ESRT
f
I
IAC
IAC,rms
IAC,f
IAC,max
IAC,R
IAC,R (B)
Ileak
Ileak,op
l
lmax
R
Rins
Rsymm
T
∆T
TA
TC
TB
t
∆t
tb
Please read Cautions and warnings and
Important notes at the end of this document.
Ersatzserienwiderstand bei Temperatur T
Frequenz
Strom
Wechselstrom
Wechselstrom, Effektivwert
Wechselstrom bei Frequenz f
Maximal zulässiger Wechselstrom
Nennwechselstrom
Nennwechselstromstrom für Bodenkühlung
Ableitstrom
Ableitstrom bei Betrieb
Gehäuselänge, Nennmaß
Maximale Gehäuselänge (ohne Anschlüsse
und Gewindebolzen)
Widerstand
Isolationswiderstand
Symmetrierwiderstand
Temperatur
Temperaturdifferenz
Umgebungstemperatur
Gehäusetemperatur
Temperatur des Becherbodens
Zeit
Zeitraum
Brauchbarkeitsdauer (Betriebszeit)
Page 17 of 19
B41252
Standard series 105 °C
Symbol
V
VF
Vop
VR
VS
XC
XL
Z
ZT
tan δ
λ
ε0
εr
ω
English
Voltage
Forming voltage
Operating voltage
Rated voltage, DC voltage
Surge voltage
Capacitive reactance
Inductive reactance
Impedance
Impedance at temperature T
Dissipation factor
Failure rate
Absolute permittivity
Relative permittivity
Angular velocity; 2 π f
German
Spannung
Formierspannung
Betriebsspannung
Nennspannung, Gleichspannung
Spitzenspannung
Kapazitiver Blindwiderstand
Induktiver Blindwiderstand
Scheinwiderstand
Scheinwiderstand bei Temperatur T
Verlustfaktor
Ausfallrate
Elektrische Feldkonstante
Dielektrizitätszahl
Kreisfrequenz; 2 π f
Notes
All dimensions are given in mm.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 18 of 19
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar
with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or
failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in
which the malfunction or failure of an electronic component could endanger human life or
health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by
means of suitable design of the customer application or other action taken by the customer
(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by
third parties in the event of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order. We also
reserve the right to discontinue production and delivery of products. Consequently, we
cannot guarantee that all products named in this publication will always be available. The
aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the "General Terms of Delivery for Products and Services in the Electrical Industry" published by the German Electrical and Electronics Industry Association
(ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSSP, CTVS, DSSP, MiniBlue, MKK,
MLSC, MotorCap, PCC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap,
SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks
registered or pending in Europe and in other countries. Further information will be found on
the Internet at www.epcos.com/trademarks.
Page 19 of 19