HLCP-J100 10-Element Bar Graph Array Data Sheet HLCP-J100 HDSP-4820 HDSP-4830 HDSP-4832 Description These 10-element LED arrays are designed to display information in easily recognizable bar graph form. The packages are end stackable and therefore capable of displaying long strings of information. Use of these bar graph arrays eliminates the alignment, intensity, and color matching problems associated with discrete LEDs. The HDSP-4820/4830/4840/4850 and HLCP-J100 each contain LEDs of one color. The HDSP-4832/4836 are multicolor arrays with High Efficiency Red, Yellow, and High Performance Green LEDs in a single package. Applications • Industrial controls • Instrumentation • Office equipment • Computer peripherals • Consumer products Features • Custom multicolor array capability • Matched LEDs for uniform appearance • End stackable • Package interlock ensures correct alignment • Low profile package • Rugged construction • Large, easily recognizable segments • High ON-OFF contrast, segment to segment • Wide viewing angle • Categorized for luminous intensity • HDSP-4832/4836/4840/4850 categorized for dominant wavelength • HLCP-J100 operates at low current Typical intensity of 1.0 mcd at 1 mA drive current Package Dimensions 25.40 (1.000) MAX. 0.38 (0.015) 10.16 (0.400) MAX. 5.08 (0.200) 2.54 (0.100) DATE CODE PIN ONE MARKING 1.52 (0.060) LUMINOUS INTENSITY CATEGORY COLOR BIN (NOTE 3) HDSP XXXX XYY 0.61 (0.024) 1. DIMENSIONS IN MILLIMETERS (INCHES). 2. ALL UNTOLERANCED DIMEMSIONS FOR REFERENCE ONLY. 3. HDSP-4832/-4836/-4840/-4850 ONLY. 6.10 ± 0.25 (0.240 ± 0.010) 5.08 (0.200) ZW 2.54 ± 0.25 (0.100 ± 0.010) 4.06 (0.160) MIN. 0.38 (0.015) 7.62 ± 0.38 (0.300 ± 0.015) Absolute Maximum Ratings[7] Parameter Average Power Dissipation per LED (TA = 25°C) Peak Forward Current per LED DC Forward Current per LED Operating Temperature Range Storage Temperature Range Reverse Voltage per LED Lead Solder Dipping Temperature (1.59 mm (1/16 inch) below seating plane)[6] Wave Soldering Temperature (at 2 mm distance from the body) Red HDSP-4820 63 mW AlGaAs Red HLCP-J100 37 mW HER HDSP-4830 87 mW Yellow Green HDSP-4840 HDSP-4850 50 mW 105 mW 150 mA[1] 30 mA[4] -40°C to +85°C -40°C to +85°C 3.0 V 45 mA[2] 90 mA[3] 60 mA[3] 15 mA[4] 30 mA[5] 20 mA[5] -20°C to +100°C -40°C to +85°C -55°C to +100°C -40°C to +85°C 5.0 V 3.0 V [8] 260°C for 5 seconds 90 mA[3] 30 mA[5] -20°C to +85°C 250°C for 3 seconds Notes: 1. See Figure 1 to establish pulsed operating conditions. Maximum pulse width is 1.5 ms. 2. See Figure 2 to establish pulsed operating conditions. Maximum pulse width is 1.5 ms. 3. See Figure 8 to establish pulsed operating conditions. Maximum pulse width is 2 ms. 4. Derate maximum DC current for Red above TA = 62°C at 0.79 mA/°C, and AlGaAs Red above TA = 91°C at 0.8 mA/°C. See Figure 3. 5. Derate maximum DC current for HER above TA = 48°C at 0.58 mA/°C, Yellow above TA = 70°C at 0.66 mA/°C, and Green above TA = 37°C at 0.48 mA/°C. See Figure 9. 6. Clean only in water, isopropanol, ethanol, Freon TF or TE (or equivalent), or Genesolve DI-15 (or equivalent). 7. Absolute maximum ratings for HER, Yellow, and Green elements of the multicolor arrays are identical to the HDSP-4830/4840/4850 maximum ratings. 8. Maximum tolerable component side temperature is 134°C during solder process. Internal Circuit Diagram 1 2 3 b c 20 Pin Function Pin Function 19 1 2 3 4 5 6 7 8 9 10 Anode a Anode b Anode c Anode d Anode e Anode f Anode g Anode h Anode i Anode j 11 12 13 14 15 16 17 18 19 20 Cathode j Cathode i Cathode h Cathode g Cathode f Cathode e Cathode d Cathode c Cathode b Cathode a 18 4 d 17 5 e 16 6 7 8 9 10 2 a f g h i j 15 14 13 12 11 Multicolor Array Segment Colors HDSP-4832 Segment Segment Color a HER b HER c HER d Yellow e Yellow f Yellow g Yellow h Green i Green j Green HDSP-4836 Segment Color HER HER Yellow Yellow Green Green Yellow Yellow HER HER Electrical/Optical Characteristics at TA = 25°C[4] Red HDSP-4820 Parameter Symbol Luminous Intensity per LED (Unit Average)[1] IV Peak Wavelength lPEAK Dominant Wavelength[2] ld Forward Voltage per LED VF Reverse Voltage per LED[5] VR Temperature Coefficient VF per LED ∆VF/°C Thermal Resistance LED Junction-to-Pin RqJ-PIN AlGaAs Red HLCP-J100 Parameter Luminous Intensity per LED (Unit Average)[1] Symbol IV Peak Wavelength Dominant Wavelength[2] Forward Voltage per LED lPEAK ld VF Reverse Voltage per LED[5] Temperature Coefficient VF per LED Thermal Resistance LED Junction-to-Pin 3 VR ∆VF/°C RqJ-PIN Min. 610 3 Min. 600 5 Typ. 1250 655 645 1.6 12 -2.0 300 Max. Typ. 1000 5200 Max. 645 637 1.6 1.8 15 -2.0 300 2.0 Units µcd nm nm V V mV/°C °C/W/LED Test Conditions IF = 20 mA Units µcd Test Conditions IF = 1 mA IF = 20 mA Pk; 1 of 4 Duty Factor nm nm V 2.2 V mV/°C °C/W/LED IF = 20 mA IR = 100 µA IF = 1 mA IF = 20 mA IR = 100 µA High Efficiency Red HDSP-4830 Parameter Luminous Intensity per LED (Unit Average)[1,4] Peak Wavelength Dominant Wavelength[2] Forward Voltage per LED Reverse Voltage per LED[5] Temperature Coefficient VF per LED Thermal Resistance LED Junction-to-Pin Symbol IV lPEAK ld VF VR ∆VF/°C RqJ-PIN Min. 900 Yellow HDSP-4840 Parameter Symbol IV Luminous Intensity per LED (Unit Average)[1,4] Peak Wavelength lPEAK Dominant Wavelength[2,3] ld Forward Voltage per LED VF Reverse Voltage per LED[5] VR Typ. 3500 635 626 2.1 30 -2.0 300 Max. Min. Typ. Max. 600 3 581 3 Units µcd nm nm V V mV/°C °C/W/LED Test Conditions IF = 10 mA Units Test Conditions 1900 µcd IF = 10 mA 583 nm 2.5 585 592 nm 2.2 2.5 V IF = 20 mA 40 V IR = 100 µA Temperature Coefficient VF per LED ∆VF/°C -2.0 mV/°C Thermal Resistance LED Junction-to-Pin RqJ-PIN 300 °C/W/LED Green HDSP-4850 Parameter Symbol Min. Typ. IV 600 Luminous Intensity per LED (Unit Average)[1,4] IF = 20 mA IR = 100 µA Max. Units Test Conditions 1900 µcd IF = 10 mA nm Peak Wavelength lPEAK 566 Dominant Wavelength[2,3] ld 571 577 nm Forward Voltage per LED VF 2.1 2.5 V IF = 10 mA 50 V IR = 100 µA Reverse Voltage per LED[5] VR 3 Temperature Coefficient VF per LED ∆VF/°C -2.0 mV/°C Thermal Resistance LED Junction-to-Pin RqJ-PIN 300 °C/W/LED Notes: 1. The bar graph arrays are categorized for luminous intensity. The category is designated by a letter located on the side of the package. 2. The dominant wavelength, ld, is derived from the CIE chromaticity diagram and is that single wavelength which defines the color of the device. 3. The HDSP-4832/-4836/-4840/-4850 bar graph arrays are categorized by dominant wavelength with the category designated by a number adjacent to the intensity category letter. Only the yellow elements of the HDSP-4832/-4836 are categorized for color. 4. Electrical/optical characteristics of the High-Efficiency Red elements of the HDSP-4832/-4836 are identical to the HDSP-4830 characteristics. Characteristics of Yellow elements of the HDSP-4832/-4836 are identical to the HDSP-4840. Characteristics of Green elements of the HDSP-4832/-4836 are identical to the HDSP-4850. 5. Reverse voltage per LED should be limited to 3.0 V max. for the HDSP-4820/-4830/-4840/-4850/-4832/-4836 and 5.0 V max. for the HLCP-J100. 4 1 10 100 1000 10000 DC OPERATION 2 1 1 10 tP – PULSE DURATION – µSEC IDC MAX – MAXIMUM DC CURRENT PER SEGMENT – mA 40 Rθ J-A = 600°C/W 35 RED 25 20 15 AlGaAs RED 10 5 0 25 35 45 55 65 75 85 95 105 η PEAK – RELATIVE EFFICIENCY (NORMALIZED TO 1 AT 20 mA FOR RED: AT 1mA FOR AlGaAs RED) Figure 1. Maximum Tolerable Peak Current vs. Pulse Duration – Red. 30 1000 10000 DC OPERATION Figure 2. Maximum Tolerable Peak Current vs. Pulse Duration – AlGaAs Red. 1.2 1.1 AlGaAs RED RED 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0 20 40 60 80 100 120 140 160 IPEAK – PEAK SEGMENT CURRENT – mA TA – AMBIENT TEMPERATURE – °C Figure 3. Maximum Allowable DC Current vs. Ambient Temperature. TJMAX = 100°C for Red and TJMAX = 110°C for AlGaAs Red. Figure 4. Relative Efficiency (Luminous Intensity per Unit Current) vs. Peak Current. 1.4 160 140 RED 120 100 80 60 40 AlGaAs RED 20 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 VF – FORWARD VOLTAGE – V Figure 5. Forward Current vs. Forward Voltage. 20 RELATIVE LUMINOUS INTENSITY (NORMALIZED TO 1 AT 1mA) RELATIVE LUMINOUS INTENSITY (NORMALIZED TO 1.0 AT 20 mA) 100 tP – PULSE DURATION – µs IF – FORWARD CURRENT PER SEGMENT – mA 1 3 OPERATION IN THIS REGION REQUIRES TEMPERATURE DERATING OF IDC MAX TE RA 1.5 H ES EFR f-R Hz 100 Hz 300 Hz 2 4 z TE RA 3 5 1K z 6 5 4 10 9 8 7 6 Hz 10 K OPERATION IN THIS REGION REQUIRES TEMPERATURE DERATING OF IDC MAX ESH EFR f-R Hz 100 Hz 300 z Hz KH 8 1K 10 15 12.5 10 3KH IPEAK MAX RATIO OF MAXIMUM OPERATING PEAK CURRENT TO TEMPERATURE IDC MAX DERATED MAXIMUM DC CURRENT 20 3KH IPEAK MAX RATIO OF MAXIMUM OPERATING PEAK CURRENT TO TEMPERATURE IDC MAX DERATED MAXIMUM DC CURRENT Red, AlGaAs Red 1.2 1.0 0.8 0.6 0.4 0.2 0 0 5 10 15 20 25 IF – FORWARD CURRENT PER SEGMENT – mA Figure 6. Relative Luminous Intensity vs. DC Forward Current – Red. 10 5 2 1 0.1 0.1 0.2 0.5 1 5 10 20 IF – FORWARD CURRENT PER SEGMENT Figure 7. Relative Luminous Intensity vs. DC Forward Current – AlGaAs. For a Detailed Explanation on the Use of Data Sheet Information and Recommended Soldering Procedures, See Application Note 1005. 5 IPEAK MAX RATIO OF MAXIMUM OPERATING PEAK CURRENT TO TEMPERATURE IDC MAX DERATED MAXIMUM DC CURRENT HER, Yellow, Green 20 15 GREEN 12 10 8 OPERATION IN THIS REGION REQUIRES TEMPERATURE DERATING OF IDC MAX HER fH ES FR RE 6 YELLOW 4 z Hz 0H 30 1K z Hz KH 3K 10 2 TE Hz RA 100 3 1.5 1 1 10 100 1000 10000 DC OPERATION tP – PULSE DURATION – µSEC Figure 8. Maximum Tolerable Peak Current vs. Pulse Duration – HER/Yellow/Green. IDC MAX – MAXIMUM DC CURRENT PER SEGMENT – mA Rθ J-A = 600°C/W 35 GREEN/HER 30 GREEN 25 HER YELLOW 20 YELLOW 15 10 5 0 15 ηPEAK – RELATIVE EFFICIENCY 1.6 40 1.5 YELLOW SERIES 1.4 HER SERIES 1.3 GREEN SERIES 1.2 1.1 1.0 0.9 0.8 0.7 0.6 25 35 45 55 65 75 85 0 10 20 30 40 50 60 70 80 90 100 95 IPEAK – PEAK SEGMENT CURRENT – mA TA – AMBIENT TEMPERATURE – °C Figure 10. Relative Efficiency (Luminous Intensity per Unit Current) vs. Peak Current. 90 4.0 GREEN SERIES 80 70 60 YELLOW SERIES 50 40 30 HER SERIES 20 10 0 1.0 RELATIVE LUMINOUS INTENSITY IF – FORWARD CURRENT PER SEGMENT – mA Figure 9. Maximum Allowable DC Current vs. Ambient Temperature. TJMAX = 100°C. 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 2.0 3.0 4.0 5.0 VF – FORWARD VOLTAGE – V Figure 11. Forward Current vs. Forward Voltage. 0 5 10 15 20 25 30 35 40 IF – FORWARD CURRENT PER SEGMENT – mA Figure 12. Relative Luminous Intensity vs. DC Forward Current. For a Detailed Explanation on the Use of Data Sheet Information and Recommended Soldering Procedures, See Application Note 1005. 6 Electrical/Optical These versatile bar graph arrays are composed of ten light emitting diodes. The light from each LED is optically stretched to form individual elements. The Red (HDSP-4820) bar graph array LEDs use a p-n junction diffused into a GaAsP epitaxial layer on a GaAs substrate. The AlGaAs Red (HLCP-J100) bar graph array LEDs use double heterojunction AlGaAs on a GaAs substrate. HER (HDSP4830) and Yellow (HDSP-4840) bar graph array LEDs use a GaAsP epitaxial layer on a GaP substrate. Green (HDSP-4850) bar graph array LEDs use liquid phase GaP epitaxial layer on a GaP substrate. The multicolor bar graph arrays (HDSP-4832/ 4836) have HER, Yellow, and Green LEDs in one package. These displays are designed for strobed operation. The typical forward voltage values can be scaled from Figures 5 and 11. These values should be used to calculate the current limiting resistor value and typical power consumption. Expected maximum VF values for driver circuit design and maximum power dissipation may be calculated using the VFMAX models: 7 Standard Red HDSP-4820 series VFMAX = 1.8 V + IPeak (10 Ω) For: IPeak ≥ 5 mA AlGaAs Red HLCP-J100 series VFMAX = 1.8 V + IPeak (20 Ω) For: IPeak ≤ 20 mA VFMAX = 2.0 V + IPeak (10 Ω) For: IPeak ≥ 20 mA HER (HDSP-4830) and Yellow (HDSP-4840) series VFMAX = 1.6 + IPeak (45 Ω) For: 5 mA ≤ IPeak ≤ 20 mA VFMAX = 1.75 + IPeak (38 Ω) For: IPeak ≥ 20 mA Green (HDSP-4850) series VFMAX = 2.0 + IPeak (50 Ω) For: IPeak > 5 mA Figures 4 and 10 allow the designer to calculate the luminous intensity at different peak and average currents. The following equation calculates intensity at different peak and average currents: IVAVG = (IFAVG/IFAVG DATA SHEET)hpeak)(IVDATA SHEET) Where: IVAVG is the calculated time averaged luminous intensity resulting from IFAVG. IFAVG is the desired time averaged LED current. IFAVG DATA SHEET is the data sheet test current for IVDATA SHEET. hpeak is the relative efficiency at the peak current, scaled from Figure 4 or 10. IV DATA SHEET is the data sheet luminous intensity, resulting from IFAVG DATA SHEET. For example, what is the luminous intensity of an HDSP4830 driven at 50 mA peak 1/5 duty factor? IFAVG = (50 mA)(0.2) = 10 mA IFAVG DATA SHEET = 10 mA hpeak = 1.3 IV DATA SHEET = 3500 µcd Therefore IVAVG = (10 mA/10 mA) (1.3)(3500 µcd) = 4550 µcd For product information and a complete list of distributors, please go to our website: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries. Data subject to change. Copyright © 2006 Avago Technologies Limited. All rights reserved. Obsoletes 5989-2902EN AV01-0277EN June 26, 2006