Compact Flash© Card Connectors Complies with Compact Flash Association MI20/21 Series (a)Space-saving design .75 0 7. 51 ■Features (b)Suitable for automatic mounting 1. Compact design occupies minimum space Automatic equipment pick up area. Connectors are designed with small width and depth for miniaturization and the foot print on the board has been made smaller. (See (a) to the right) 2. Supplied with ground terminals The MI21 Series are furnished with ground terminals. 3. Card ejection mechanism Two point ejection mechanism to assure even card ejection. 4. Designed and packaged for board placement with automatic equipment Headers are designed with a pick up area to accommodate the pick-and -place nozzles of automatic mounting machines. (Patents pending) Receptacles are designed to be mounted on top the board, and automatic mounting is possibble on the specified board. 5. Card ejection mechanism Available in several termination and mouting styles, with and without ejection mechanism, with and without standoffs. Fixed HRS Product Feature Fixed fittings make slider immobile. Construction facilitates pick-and-place process. ●Producut variation Series Mounting offset None 6. Rich variations A rich assortment of variations allows selection of a type to suit the specific card and the equipment to which it will be installed. (1)Suitable cards: Type I , type I/II . (2)Eject button: None, right , left (3)Standoff: 0 mm, 2.2 mm (4)Board mounting type: Standard , reverse Ejector None Type1or2 ---- Type1 YES Right Standard 2.2 mm MI20 Cards Built-in nuts Left Reverse 2.2 mm None None Type1 Ø(None) Right Left Standard MI21 Type1or2 Reverse 2.2 mm None None None Note 1: Hexagonal nuts (M2∞0.4) are required. ■Applications PDA, digital still cameras, etc. C2 YES ■ Product Specifications Current rating 0.5 A Rating Voltage rating 125 V AC Operating temperature range -55 to +85ç (Note 1) Storage temperature range -10 to +60ç Operating humidity range Relative humidity 95% or less Storage humidity range -40 to 70% (No condensation) Item Specification 1. Insulation resistance Conditions 500 V DC 1,000 M ohms min. 2. Withstanding voltage No flashover or insulation breakdown. 500 V AC / 1 minute 3. Contact resistance 40 m ohms max. (initial value) (Note 3) 1 mA 4. Vibration No electrical discontinuity of 100ns or more Frequency: 10 to 2000 Hz, full amplitude of 1.52 mm or acceleration of 147 m/s2(peak), 4 hours in each of the 3 directions. 5. Humidity (Steady state) Insulation resistance of 100 M ohms min. 96 hours at temperature of 40ç and humidity of 90% to 95% 6. Temperature cycle Insulation resistance of 100 M ohms min. Temperature: -55ç for 30 min. --> +5 to 35ç within 5 min. 85ç for 30 min. --> +5 to 35ç within 5 min. for 5 cycles 7. Durability (Insertion/withdrawal) Change of contact resistance from initial value is 20 m ohms max. 10000 cycles at 400 to 600 cycles per hour 8. Resistance to Soldering No deformation of components affecting performance. heat Reflow: At the recommended temperature profile Manual soldering: 300ç for 3 seconds Note 1: Includes temperature rise caused by current flow. Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers non- conducting condition of installed connectors in storage, shipment or during transportation. Note 3: This does not include the resistance of the conductor . ■Materials Item Receptacle Header Part Material Finish Remarks Insulator PPS Color:Black UL94V-0 Contacts Phosphor bronze Contact Area : Gold plating Lead Area : Solder plating --------------- Insulator PPS Color:Black UL94V-0 Contacts Brass Contact Area : Gold plating Termination Area : Solder plating --------------- Metal fitting Brass --------------- Applied to eject mechanism Eject fitting Stainless steel --------------- --------------- Ground clip Stainless steel --------------- Applied to MI21 series Nut Steel Solder plating --------------- ■Ordering Information ●Receptacles 1 Series name: MI MI 20 - 50 RD - SF 1 2 3 4 2 Series No. 20: for type I cards (✽) 5 21: for type I and II cards 1 Series name: MI 2 Series No.: 20 3 Number of contacts: 50 4 Connector type 5 Contact form 3 Stand off type Blank : None A RD: Receptacle SF: SMT ●Headers : 2.2 mm 2 4 5 6 7 R : Reverse 7 Contact type SF: SMT 8 Eject button position EJR : Right button EJL 5 Connector type Blank : None PD: Header 3 Blank : Standard 4 Number of contacts: 50 MI 20 A - 50 PD R - SF - EJR (31) 1 6 Board mounting type : Left button 9 Built-in nut type (31): With built-in nuts Blank: Standard product 8 9 (✽) Can accommodate type II cards only when standard mounting is used and stand off is 0 mm. C3 ■Receptacle 35.86 32.97 30.48 No.1 3.3 1.27 1.27 No.25 -2 No.26 No.50 2.7 2.6 3 6 0.5 0.2 (offset) No.1 No.26 0.635 No.50 No.25 (t0.08∞w0.3) 1 1 A 31.115 Note 1 The coplanarity of the conductor is 0.1 mm Max. Part Number CL No. Number of Contacts Packaging MI20-50RD-SF 640-7001-0 50 Tray BPCB mounting pattern (35) 33.4 +0.1 +0 31.115±0.05 50-0.4±0.03 3max 0.635±0.03 1.2 +0.2 +0 2min (4.2) 2-R1max (Recommended board thickness=0.4) C4 0.05 ■Headers for Type I or II Cards ●Eject button : None ●Offset : None ●Mounting style : Standard mounting 1.95 49 48 No.50 No.38 No.26 No.25 No.13 No.1 30 12.25 18 (20) 43.03 (10) MI20--50PD 0.635 No.50 31.115 No.2 No.26 Polartiy mark No.1 No.25 40.4 2.5 (0.8) 1.35 3.8 2.5 t : 0.25 ∞ w : 0.25 Note 1: Coplanarity of all surface mount terminals and components is 0.1. Note 2: Dimensions in parentheses ( ) are reference dimensions. Part Number CL No. Number of Contacts Packaging MI20-50PD-SF 640-7002-2 50 Tray BPCB mounting pattern 51±0.1 45.5±0.05 44.6±0.1 37±0.05 4.5max 4±0.05 +0 +0 .1 .1 +0 0 .6 + Ø1 2- 8.25min 18±0.05 12.25±0.1 2-Ø 1.4 2.9425±0.05 No.1 0.634±0.03 50-0.4±0.03 31.115±0.05 C5 ■Headers for Type I Cards 48.3 46.3 4.15 ●Eject button : None ●Offset : 2.2 mm ●Mounting style : Reverse mounting No.1 No.13 No.25 No.38 No.50 No.26 22.25 37.9 (27.9) 43.03 (10) (4.5) (17.2) No.1 No.2 0.635 No.25 No.26 No.50 31.115 42.3 33.7 (4.3) (1) (0.15) 6.6 (4.3) t : 0.25∞w : 0.25 44 Note 1: Coplanarity of all surface mount terminals and components is 0.1. Note 2: Dimensions in parentheses ( ) are reference dimensions. Part Number CL No. Number of Contacts Packaging MI20A-50PDR-SF 640-7003-5 50 Tray BPCB mounting pattern 44±0.05 +0.1 0 41.3±0.05 37±0.05 3.5±0.05 4±0.1 28.5±0.05 43.9±0.1 50.3±0.1 +0.1 0 1.6 + +0.1 0 2.4 + 2-Ø 2-Ø 8.25min 22.25±0.1 2-Ø1.3 + 1 4.5max 2.9425±0.05 No.1 0.635±0.03 31.115±0.05 50-0.4±0.03 ) illustrated in the figure are only required when screws are used for fastening. Note 1 The holes (2-Ø2.4 +0.1 0 C6 ■Headers for Type I Cards ●Eject button : Right button ●Offset : 2.2 mm ●Mounting style : Standard mounting Note 1: The amount of card and button protrusion from the connector after mating is 13.6 mm. Note 2: The dimensions of mating portion of this product comply with CFA standards. Note 3: This product can be automatically mounted. The suction surface for automatic mounting is positioned as illustrated in the figure. 3 This part is fixed in the initial condition, but released with a single operation of the ejector. (Amount of actual card ejection: 3.5 mm) Note 4: The coplanarity (degree of flatness) of the SMT lead tip portion and the reinforced fitting mounting end face is to be 0.1 maximum. Note 5: Dimensions in parentheses ( ) are to be regarded as reference dimensions. Part Number CL No. Number of Contacts Packaging MI20A-50PD-SF-EJR 640-7004-8 50 Tray BPCB mounting pattern ) illustrated in the figure are only required when screws are used for fastening. Note 1 The holes (2-Ø2.4 +0.1 0 C7 ■Headers for Type I Cards ●Eject button : Left side ●Offset : 2.2 mm ●Mounting style : Standard mounting Note 1: The amount of card and button protrusion from the connector after mating is 13.6 mm. Note 2: The dimensions of mating portion of this product comply with CFA standards. Note 3: This product can be automatically mounted. The suction surface for automatic mounting is positioned as illustrated in the figure. 3 This part is fixed in the initial condition, but released with a single operation of the ejector. (Amount of actual card ejection: 3.5 mm) Note 4: The coplanarity (degree of flatness) of the SMT lead tip portion and the reinforced fitting mounting end face is to be 0.1 maximum. Note 5: Dimensions in parentheses ( ) are to be regarded as reference dimensions. Part Number CL No. Number of Contacts Packaging MI20A-50PD-SF-EJL 640-7005-0 50 Tray BPCB mounting pattern ) illustrated in the figure are only required when screws are used for fastening. Note 1 The holes (2-Ø2.4 +0.1 0 C8 ■Headers for Type I or II Cards ●Eject button : Right side ●Offset : 0 mm ●Mounting style : Standard mounting Note 1: This item is a (standard type) header for use with CompactFlash cards. Note 2: The dimensions of mating portion of this product comply with CFA standards. Note 3: This product can be automatically mounted. The suction surface for automatic mounting is positioned as illustrated in the figure. 3 This part is fixed in the initial condition, but released with a single operation of the ejector. (Amount of actual card ejection: 3.5 mm) Note 4: The coplanarity (degree of flatness) of the SMT lead tip portion and the reinforced fitting mounting end face is to be 0.1 maximum. Note 5: Dimensions in parentheses ( ) are to be regarded as reference dimensions. Part Number CL No. Number of Contacts Packaging MI21-50PD-SF-EJR 640-7107-0 50 Tray BPCB mounting pattern ) illustrated in the figure are only required when screws are used for fastening. Note 1 The holes (2-Ø2.4 +0.1 0 C9 ■Headers for Type I or II Cards ●Eject button : Left side ●Offset : None ●Mounting style : Standard mounting Note 1: This item is a (standard type) header for use with CompactFlash cards. Note 2: The dimensions of mating portion of this product comply with CFA standards. Note 3: This product can be automatically mounted. The suction surface for automatic mounting is positioned as illustrated in the figure. 3 This part is fixed in the initial condition, but released with a single operation of the ejector. (Amount of actual card ejection: 3.5 mm) Note 4: The coplanarity (degree of flatness) of the SMT lead tip portion and the reinforced fitting mounting end face is to be 0.1 maximum. Note 5: Dimensions in parentheses ( ) are to be regarded as reference dimensions. Part Number CL No. Number of Contacts Packaging MI21-50PD-SF-EJL 640-7108-3 50 Tray BPCB mounting pattern ) illustrated in the figure are only required when screws are used for fastening. Note 1 The holes (2-Ø2.4 +0.1 0 C10 ■Headers for Type I or II Cards ●Eject button : None ●Offset : None ●Mounting style : Standard mounting Note 1: This item is a (standard type) header for use with CompactFlash cards. Note 2: The dimensions of mating portion of this product comply with CFA standards. Note 3: The coplanarity (degree of flatness) of the SMT lead tip portion and the reinforced fitting mounting end face is to be 0.1 maximum Note 4: Dimensions in parentheses ( ) are to be regarded as reference dimensions. Part Number CL No. Number of Contacts Packaging MI21-50PD-SF 640-7109-6 50 Tray BPCB mounting pattern ) illustrated in the figure are only required when screws are used for fastening. Note 1 The holes (2-Ø2.4 +0.1 0 C11 ■Headers for Type I or II Cards ●Eject button : None ●Offset : None ●Mounting style : Reverse mounting Note 1: Coplanarity of all surface mount terminals and components is 0.1. Note 2: Dimensions in parentheses ( ) are reference dimensions. Part Number CL No. Number of Contacts Packaging MI21A-50PDR-SF 640-7106-8 50 Tray BPCB mounting pattern C12 ■Headers for Type I and II Cards ●Eject button : Right side ●Offset : 2.2 mm ●Mounting style : Standard mounting Note 1: This item is a (standard type) header for use with CompactFlash cards. Note 2: The dimensions of mating portion of this product comply with CFA standards. Note 3: This product can be automatically mounted. The suction surface for automatic mounting is positioned as illustrated in the figure. 3 This part is fixed in the initial condition, but released with a single operation of the ejector. (Amount of actual card ejection: 3.5 mm) Note 4: The coplanarity (degree of flatness) of the SMT lead tip portion and the reinforced fitting mounting end face is to be 0.1 maximum. Note 5: Dimensions in parentheses ( ) are to be regarded as reference dimensions. Part Number CL No. Number of Contacts Packaging MI21A-50PD-SF-EJR 640-7101-4 50 Tray BPCB mounting pattern ) illustrated in the figure are only required when screws are used for fastening. Note 1 The holes (2-Ø2.4 +0.1 0 C13 ■Headers for Type I and II Cards ●Eject button : Left button ●Offset : 2.2 mm ●Mounting style : Standard mounting Note 1: This item is a (standard type) header for use with CompactFlash cards. Note 2: The dimensions of mating portion of this product comply with CFA standards. Note 3: This product can be automatically mounted. The suction surface for automatic mounting is positioned as illustrated in the figure. 3 This part is fixed in the initial condition, but released with a single operation of the ejector. (Amount of actual card ejection: 3.5 mm) Note 4: The coplanarity (degree of flatness) of the SMT lead tip portion and the reinforced fitting mounting end face is to be 0.1 maximum. Note 5: Dimensions in parentheses ( ) are to be regarded as reference dimensions. Part Number CL No. Number of Contacts Packaging MI21A-50PD-SF-EJL 640-7102-7 50 Tray BPCB mounting pattern ) illustrated in the figure are only required when screws are used for fastening. Note 1 The holes (2-Ø2.4 +0.1 0 C14 ■Headers for Type I and II Cards ●Eject button : None ●Offset : 2.2 mm ●Mounting style : Standard mounting Note 1: Coplanarity of all surface mount terminals and components is 0.1. Note 2: Dimensions in parentheses ( ) are reference dimensions. Part Number CL No. Number of Contacts Packaging MI21A-50PD-SF 640-7103-0 50 Tray BPCB mounting pattern ) illustrated in the figure are only required when screws are used for fastening. Note 1 The holes (2-Ø2.4 +0.1 0 C15 BTemperature Profile Applicable Conditions Reflow system : IR reflow Solde : Paste type 63 Sn/37 Pb (Flux content 9 wt%) Test board Glass epoxy 60mm x 60mm x 1.6 mm Metal mask thickness: 0.15 mm Recommended temperature profile. The temperature may be slightly changed according to the solder paste type and amount. C16 BPrecautions for Use 1. Differentiate the side of the card at the time of CF card insertion. This product is furnished with an wrong insertion prevention mechanism which is compliant with CFA standards, but forced wrong insertion of the card may cause damage to the card. 2. Do not move the CF card up and down when it has been partially inserted. It may cause damage to the connector and card. Up CF Card Down 3. The package used for this product is the soft tray. We recommend a check before mounting, since the adjustment may be reqaired depending on the type of mounter. For more detailed information, please contact nearest Hirose account representative. 4. Recommended screw torque values. Screw type Standard torque [Unit: N'm] Upper tolerance limit Steel screws 0.142 0.180 0.124 0.168 Brass screws •Screws : M2 X 0.4 BWashing Conditions This product is a no-wash item, but in the case of washing, please observe the following conditions. 1. Organic Solvent Washing Solvent Room temperature washing Heated washing IPA (Isopropyl alcohol) YES YES HCFC (Hydrochlorofluorocarbon) YES YES 2. Water Type Washing When using water type cleaning agents (e.g., terpene, and alkali saponifiers), select the cleaning agent based on the documentation issued by the various manufacturers of cleaning agents which describes the effects on metals and resins. Be careful that parts are not left with moisture remaining on them. 3. Washing Precautions Residual flux or cleaning agent on the contacts when washing with organic solvents or water type cleaners can give rise to the deterioration of electrical performance. In this regard it is important to check whether a thorough washing has been performed. C17