RoHS KPC35005W-3510W SINGLE-PHASE BRIDGE RECTIFIER FEATURES Low cost This series is UL recognized under component index, file number E127707 High forward surge current capability Low thermal resistance. High isolation voltage from case to leads. High temperature soldering guaranteed: 260/10 second, at 5 lbs. (2.3kg) tension. MECHANICAL DATA Case: Metal case Terminal: Plated 0.04" (1.02mm) lug. Polarity: Polarity symbols marked on case. Mounting: Thru hole for #10 screw, 20 in,- lbs. Torqute Max. Weight: 0.93 ounce, 26.4gram R T O MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 ambient temperature unless otherwise specified Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load derate current by 20% C E L SYMBOLS Maximum Repetitive Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Output Current, at TC = 50 (Note 1,2) Peak Forward Surge Current 8.3ms single half sine - wave superimposed on rated load (JEDEC method ) Rating for Fusing (t<8.3ms) J E E Maximum Instantaneous Forward Voltage Drop per bridge element at 17.5A Maximum DC Reverse Current at rated TA = 25 DC blocking voltage per element TA Isolation Voltage from case to leads. Typical Thermal Resistance Operating Temperature Range Storage Temperature Range W IC C D T ,. L O N KBPC KBPC KBPC KBPC KBPC KBPC KBPC 35005W 3501W 3502W 3504W 3506W 3508W 3510W VRRM VRMS VDC 400 280 400 Volts Volts Volts I(AV) Amps IFSM Amps 2 2 It As VF Volts IR A mA VAC /W VISO R TJ TSTG 2.0 (-65 to +150) (-65 to +150) 1. Unit mounted on 9" X 3.5" X 4.6" (23cm X 9cm X 11.8cm)Al. finned Plate. 2. Bolt down on heat-sink with silicon thermal compound between bridge and mounting sutfae for maximum heat transfer efficiency with # 10 screw. WEJ ELECTRONIC CO. UNIT MB3505W MB351W MB352W MB354W MB356W MB358W MB3510W Http:// www.wej.cn E-mail:[email protected] RoHS KPC35005W-3510W FIG.1-DERATING CURVE FOR FORWARD SURGE CURRENT PER ELEMENT 700 9"X 3.5"X 4.6" Thick (23 X 9 X 11.8cm) AL.Finned Plate Single Phase Half Wave 60Hz 10 Inductive or Resistive 600 8.3ms Single Half Sine-Wave Tj (JEDEC Method) =T 500 CURRENT, (A) PEAK FORWARD SURGE Heat Sink Mounting CURRENT,(A) AVERAGE FORWARD OUTPUT 30 20 1 Cycle 400 300 200 100 Load 0 1 0 25 0 50 75 D T ,. L O FIG.2-MAXIMUM NON-REPETITIVE PEAK OUTPUT RECTIFIED CURRENT 35 125 100 150 2 4 6 8 10 175 20 C j max 40 60 100 NUMBER OF CYCLES AT 60 Hz CASE TEMPERATURE, ( ° C) FIG.4-TYPICAL REVERSE FIG.3-TYPICAL FORWARD CHARACTERISTICS R T Tj =25 ° C Pulse Width=300uS 1%Duty Cycle 0.1 0.6 C E L 1.0 0.8 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE,(V) 1.8 Tj =100 ° C O N 10 (uA) INSTANTANEOUS REVERSE CURRENT, 1.0 0.4 IC 100 10 (A) INSTANTANEOUS FORWARD CURRENT, 100 0.01 CHARACTERISTICS PER BRIDGE ELEMENT PER BRIDGE LEMENT 1.0 Tj =25 ° C 0.1 0.01 60 40 20 0 120 100 80 140 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) FIG.5-TYPICAL JUNCTION CAPACITANCE FIG.6-MAXIMUM POWER DISSIPATION PER BRIDGE ELEMENT W Tj =25 ° C f=1MHz V sig =50mV p-p 10 0.1 1.0 10 REVRESE VOLTAGE,(V) WEJ ELECTRONIC CO. 100 Http:// www.wej.cn 80 (W) J E 100 E 100 AVERAGE POWER DISSIPATION OF BRIDGE, JUNCTION CAPACITANCE,(pF) 1000 Tj =T j max 60 Capacitive Load 40 Resistive or Inductive 20 Load 0 0 5 10 15 20 25 30 35 AVERAGE OUTPUT CURRENT, (A) E-mail:[email protected]