AD AD8400AR10 1-/2-/4-channel digital potentiometer Datasheet

1-/2-/4-Channel
Digital Potentiometers
AD8400/AD8402/AD8403
a
FEATURES
256 Position
Replaces 1, 2 or 4 Potentiometers
1 kV, 10 kV, 50 kV, 100 kV
Power Shut Down—Less than 5 mA
3-Wire SPI Compatible Serial Data Input
10 MHz Update Data Loading Rate
+2.7 V to +5.5 V Single-Supply Operation
Midscale Preset
APPLICATIONS
Mechanical Potentiometer Replacement
Programmable Filters, Delays, Time Constants
Volume Control, Panning
Line Impedance Matching
Power Supply Adjustment
FUNCTIONAL BLOCK DIAGRAM
VDD
AD8403
8-BIT
LATCH
CK
DGND
Each VR has its own VR latch that holds its programmed
resistance value. These VR latches are updated from an SPI
compatible serial-to-parallel shift register that is loaded from a
standard 3-wire serial-input digital interface. Ten data bits make
up the data word clocked into the serial input register. The data
word is decoded where the first two bits determine the address
of the VR latch to be loaded, the last eight bits are data. A serial
data output pin at the opposite end of the serial register allows
simple daisy-chaining in multiple VR applications without additional external decoding logic.
RDAC1
A1
W1
B1
SHDN
RS
AGND1
1
DAC
2
SELECT
3
A1, A0
8-BIT
LATCH
8
RDAC2
4
CK
RS
SHDN
A2
W2
B2
AGND2
2
10-BIT
SERIAL
LATCH
SDI
8
8-BIT
LATCH
CK
D
8
RDAC3
A3
W3
SHDN
RS
B3
AGND3
CK Q RS
CLK
8-BIT
LATCH
CS
GENERAL DESCRIPTION
The AD8400/AD8402/AD8403 provide a single, dual or quad
channel, 256 position digitally controlled variable resistor (VR)
device. These devices perform the same electronic adjustment
function as a potentiometer or variable resistor. The AD8400
contains a single variable resistor in the compact SO-8 package.
The AD8402 contains two independent variable resistors in
space saving SO-14 surface mount package. The AD8403 contains four independent variable resistors in 24-lead PDIP, SOIC
and TSSOP packages. Each part contains a fixed resistor with a
wiper contact that taps the fixed resistor value at a point determined by a digital code loaded into the controlling serial input
register. The resistance between the wiper and either endpoint
of the fixed resistor varies linearly with respect to the digital
code transferred into the VR latch. Each variable resistor offers
a completely programmable value of resistance, between the A
terminal and the wiper or the B terminal and the wiper. The
fixed A to B terminal resistance of 1 kΩ, 10 kΩ, 50 kΩ or 100 kΩ
has a ±1% channel-to-channel matching tolerance with a nominal
temperature coefficient of 500 ppm/°C. A unique switching circuit minimizes the high glitch inherent in traditional switched
resistor designs avoiding any make-before-break or break-beforemake operation.
8
CK
SDO
8
RDAC4
RS
SHDN
RS
SHDN
A4
W4
B4
AGND4
The reset (RS) pin forces the wiper to the midscale position by
loading 80H into the VR latch. The SHDN pin forces the resistor to an end-to-end open circuit condition on the A terminal
and shorts the wiper to the B terminal, achieving a microwatt
power shutdown state. When SHDN is returned to logic high,
the previous latch settings put the wiper in the same resistance
setting prior to shutdown. The digital interface is still active in
shutdown so that code changes can be made which will produce
new wiper positions when the device is taken out of shutdown.
The AD8400 is available in both the SO-8 surface mount and
the 8-lead plastic DIP package.
The AD8402 is available in both surface mount (SO-14) and
the 14-lead plastic DIP package, while the AD8403 is available
in a narrow body 24-lead plastic DIP and the 24-lead surface
mount package. The AD8402/AD8403 are also offered in the
1.1 mm thin TSSOP-14/TSSOP-24 package for PCMCIA applications. All parts are guaranteed to operate over the extended
industrial temperature range of –40°C to +85°C.
REV. B
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 617/329-4700
World Wide Web Site: http://www.analog.com
Fax: 617/326-8703
© Analog Devices, Inc., 1997
AD8400/AD8402/AD8403–SPECIFICATIONS
10 kV VERSION
ELECTRICAL CHARACTERISTICS
Parameter
(VDD = +3 V 6 10% or + 5 V 6 10%, VA = +VDD, VB = 0 V, –408C ≤ TA ≤ +858C unless
otherwise noted)
Symbol
Conditions
DC CHARACTERISTICS RHEOSTAT MODE Specifications Apply to All VRs
Resistor Differential NL2
R-DNL
RWB, VA = NC
R-INL
RWB, VA = NC
Resistor Nonlinearity2
Nominal Resistance3
R
TA = +25°C, Model: AD840XYY10
VAB = VDD, Wiper = No Connect
Resistance Tempco
∆RAB/∆T
Wiper Resistance
RW
IW = 1 V/R
Nominal Resistance Match
∆R/RO
CH 1 to 2, 3, or 4, VAB = VDD, TA = +25°C
DC CHARACTERISTICS POTENTIOMETER DIVIDER Specifications Apply to All VRs
Resolution
N
INL
Integral Nonlinearity4
Differential Nonlinearity4
DNL
VDD = +5 V
TA = +25°C
DNL
VDD = +3 V
DNL
VDD = +3 V
TA = –40°C, +85°C
Code = 80H
Voltage Divider Tempco
∆VW/∆T
Full-Scale Error
VWFSE
Code = FFH
Zero-Scale Error
VWZSE
Code = 00H
RESISTOR TERMINALS
Voltage Range5
Capacitance6 Ax, Bx
Capacitance6 Wx
Shutdown Current7
Shutdown Wiper Resistance
VA, B, W
CA, B
CW
IA_SD
RW_SD
DIGITAL INPUTS & OUTPUTS
Input Logic High
Input Logic Low
Input Logic High
Input Logic Low
Output Logic High
Output Logic Low
Input Current
Input Capacitance6
VIH
VIL
VIH
VIL
VOH
VOL
IIL
CIL
POWER SUPPLIES
Power Supply Range
Supply Current (CMOS)
Supply Current (TTL)8
Power Dissipation (CMOS)9
Power Supply Sensitivity
DYNAMIC CHARACTERISTICS6, 10
Bandwidth –3 dB
Total Harmonic Distortion
VW Settling Time
Resistor Noise Voltage
Crosstalk11
Min
Typ1
Max
Units
–1
–2
8
± 1/4
± 1/2
10
500
50
0.2
+1
+2
12
LSB
LSB
kΩ
ppm/°C
Ω
%
± 1/2
± 1/4
± 1/4
± 1/2
15
–2.8
+1.3
+2
+1
+1
+1.5
8
–2
–1
–1
–1.5
–4
0
0
f = 1 MHz, Measured to GND, Code = 80H
f = 1 MHz, Measured to GND, Code = 80H
VA = VDD, VB = 0 V, SHDN = 0
VA = VDD, VB = 0 V, SHDN = 0, VDD = +5 V
VDD = +5 V
VDD = +5 V
VDD = +3 V
VDD = +3 V
RL = 1 kΩ to VDD
IOL = 1.6 mA, VDD = +5 V
VIN = 0 V or +5 V, VDD = +5 V
100
1
0
+2
VDD
75
120
0.01
100
5
200
2.4
V
pF
pF
µA
Ω
5
V
V
V
V
V
V
µA
pF
0.8
2.1
0.6
VDD–0.1
0.4
±1
2.7
Bits
LSB
LSB
LSB
LSB
ppm/°C
LSB
LSB
VDD Range
IDD
IDD
PDISS
PSS
PSS
VIH = VDD or VIL = 0 V
VIH = 2.4 V or 0.8 V, VDD = +5.5 V
VIH = VDD or VIL = 0 V, VDD = +5.5 V
VDD = +5 V ± 10%
VDD = +3 V ± 10%
5.5
5
4
27.5
0.0002 0.001
0.006 0.03
V
µA
mA
µW
%/%
%/%
BW_10K
THDW
tS
eNWB
CT
R = 10 kΩ
VA = 1 V rms + 2 V dc, VB = 2 V dc, f = 1 kHz
VA = VDD, VB = 0 V, ± 1% Error Band
RWB = 5 kΩ, f = 1 kHz, RS = 0
VA = VDD, VB = 0 V
600
0.003
2
9
–65
kHz
%
µs
nV/√Hz
dB
0.01
0.9
NOTES FOR 10 kΩ VERSION
1
Typicals represent average readings at +25°C and VDD = +5 V.
2
Resistor position nonlinearity error R-INL is the deviation from an ideal value measured between the maximum resistance and the minimum resistance wiper
positions. R-DNL measures the relative step change from ideal between successive tap positions. Parts are guaranteed monotonic. See Figure 30 test circuit.
IW = 50 µA for VDD = +3 V and IW = 400 µA for VDD = +5 V for the 10 kΩ versions.
3
VAB = VDD, Wiper (VW) = No Connect.
4
INL and DNL are measured at V W with the RDAC configured as a potentiometer divider similar to a voltage output D/A converter. V A = VDD and VB = 0 V.
DNL Specification limits of ± 1 LSB maximum are Guaranteed Monotonic operating conditions. See Figure 29 test circuit.
5
Resistor terminals A, B, W have no limitations on polarity with respect to each other.
6
Guaranteed by design and not subject to production test. Resistor-terminal capacitance tests are measured with 2.5 V bias on the measured terminal. The remaining
resistor terminals are left open circuit.
7
Measured at the Ax terminals. All Ax terminals are open circuited in shutdown mode.
8
Worst case supply current consumed when input logic level at 2.4 V, standard characteristic of CMOS logic. See Figure 21 for a plot of I DD versus logic voltage.
9
PDISS is calculated from (IDD × VDD). CMOS logic level inputs result in minimum power dissipation.
10
All Dynamic Characteristics use V DD = +5 V.
11
Measured at a V W pin where an adjacent V W pin is making a full-scale voltage change.
Specifications subject to change without notice.
–2–
REV. B
SPECIFICATIONS
50 kV & 100 kV VERSION
ELECTRICAL CHARACTERISTICS
Parameter
AD8400/AD8402/AD8403
(VDD = +3 V 6 10% or + 5 V 6 10%, VA = +VDD, VB = 0 V, –408C ≤ TA ≤ +858C unless
otherwise noted)
Symbol
Conditions
DC CHARACTERISTICS RHEOSTAT MODE Specifications Apply to All VRs
Resistor Differential NL2
R-DNL
RWB, VA = NC
Resistor Nonlinearity2
R-INL
RWB, VA = NC
R
TA = +25°C, Model: AD840XYY50
Nominal Resistance3
R
TA = +25°C, Model: AD840XYY100
Resistance Tempco
∆RAB/∆T
VAB = VDD, Wiper = No Connect
IW = 1 V/R
Wiper Resistance
RW
Nominal Resistance Match
∆R/RO
CH 1 to 2, 3, or 4, VAB = VDD, TA = +25°C
DC CHARACTERISTICS POTENTIOMETER DIVIDER Specifications Apply to All VRs
Resolution
N
INL
Integral Nonlinearity4
Differential Nonlinearity4
DNL
VDD = +5 V
TA = +25°C
DNL
VDD = +3 V
DNL
VDD = +3 V
TA = –40°C, +85°C
Voltage Divider Tempco
∆VW/∆T
Code = 80H
Code = FFH
Full-Scale Error
VWFSE
Zero-Scale Error
VWZSE
Code = 00H
RESISTOR TERMINALS
Voltage Range5
Capacitance6 Ax, Bx
Capacitance6 Wx
Shutdown Current7
Shutdown Wiper Resistance
VA, B, W
CA, B
CW
IA_SD
RW_SD
DIGITAL INPUTS & OUTPUTS
Input Logic High
Input Logic Low
Input Logic High
Input Logic Low
Output Logic High
Output Logic Low
Input Current
Input Capacitance6
VIH
VIL
VIH
VIL
VOH
VOL
IIL
CIL
POWER SUPPLIES
Power Supply Range
Supply Current (CMOS)
Supply Current (TTL)8
Power Dissipation (CMOS)9
Power Supply Sensitivity
DYNAMIC CHARACTERISTICS6, 10
Bandwidth –3 dB
Total Harmonic Distortion
VW Settling Time
Resistor Noise Voltage
Crosstalk11
Min
Typ1
Max
Units
–1
–2
35
70
± 1/4
± 1/2
50
100
500
53
0.2
+1
+2
65
130
LSB
LSB
kΩ
kΩ
ppm/°C
Ω
%
±1
± 1/4
± 1/4
± 1/2
15
–0.25
+0.1
+4
+1
+1
+1.5
8
–4
–1
–1
–1.5
–1
0
0
f = 1 MHz, Measured to GND, Code = 80H
f = 1 MHz, Measured to GND, Code = 80H
VA = VDD, VB = 0 V, SHDN = 0
VA = VDD, VB = 0 V, SHDN = 0, VDD = +5 V
VDD = +5 V
VDD = +5 V
VDD = +3 V
VDD = +3 V
RL = 1 kΩ to VDD
IOL = 1.6 mA, VDD = +5 V
VIN = 0 V or +5 V, VDD = +5 V
100
1
0
+1
VDD
15
80
0.01
100
5
200
2.4
V
pF
pF
µA
Ω
5
V
V
V
V
V
V
µA
pF
0.8
2.1
0.6
VDD–0.1
0.4
±1
2.7
Bits
LSB
LSB
LSB
LSB
ppm/°C
LSB
LSB
VDD Range
IDD
IDD
PDISS
PSS
PSS
VIH = VDD or VIL = 0 V
VIH = 2.4 V or 0.8 V, VDD = +5.5 V
VIH = VDD or VIL = 0 V, VDD = +5.5 V
VDD = +5 V ± 10%
VDD = +3 V ± 10%
5.5
5
4
27.5
0.0002 0.001
0.006 0.03
V
µA
mA
µW
%/%
%/%
BW_50K
BW_100K
THDW
tS_50K
tS_100K
eNWB_50K
eNWB _100K
CT
R = 50 kΩ
R = 100 kΩ
VA = 1 V rms + 2 V dc, VB = 2 V dc, f = 1 kHz
VA = VDD, VB = 0 V, ± 1% Error Band
VA = VDD, VB = 0 V, ± 1% Error Band
RWB = 25 kΩ, f = 1 kHz, RS = 0
RWB = 50 kΩ, f = 1 kHz, RS = 0
VA = VDD, VB = 0 V
125
71
0.003
9
18
20
29
–65
kHz
kHz
%
µs
µs
nV/√Hz
nV/√Hz
dB
0.01
0.9
NOTES FOR 50 kΩ and 100 kΩ VERSIONS
1
Typicals represent average readings at +25°C and VDD = +5 V.
2
Resistor position nonlinearity error R-INL is the deviation from an ideal value measured between the maximum resistance and the minimum resistance wiper
positions. R-DNL measures the relative step change from ideal between successive tap positions. Parts are guaranteed monotonic. See Figure 30 test circuit.
IW = VDD/R for VDD = +3 V or +5 V for the 50 kΩ and 100 kΩ versions.
3
VAB = VDD, Wiper (VW) = No Connect.
4
INL and DNL are measured at V W with the RDAC configured as a potentiometer divider similar to a voltage output D/A converter. V A = VDD and VB = 0 V.
DNL Specification limits of ± 1 LSB maximum are Guaranteed Monotonic operating conditions. See Figure 29 test circuit.
5
Resistor terminals A, B, W have no limitations on polarity with respect to each other.
6
Guaranteed by design and not subject to production test. Resistor-terminal capacitance tests are measured with 2.5 V bias on the measured terminal. The remaining
resistor terminals are left open circuit.
7
Measured at the Ax terminals. All Ax terminals are open circuited in shutdown mode.
8
Worst case supply current consumed when input logic level at 2.4 V, standard characteristic of CMOS logic. See Figure 21 for a plot of I DD versus logic voltage.
9
PDISS is calculated from (IDD × VDD). CMOS logic level inputs result in minimum power dissipation.
10
All Dynamic Characteristics use V DD = +5 V.
11
Measured at a V W pin where an adjacent V W pin is making a full-scale voltage change.
Specifications subject to change without notice.
REV. B
–3–
AD8400/AD8402/AD8403–SPECIFICATIONS
1 kV VERSION
ELECTRICAL CHARACTERISTICS
Parameter
(VDD = +3 V 6 10% or + 5 V 6 10%, VA = +VDD, VB = 0 V, –408C ≤ TA ≤ +858C unless
otherwise noted)
Symbol
Conditions
DC CHARACTERISTICS RHEOSTAT MODE Specifications Apply to All VRs
Resistor Differential NL2
R-DNL
RWB, VA = NC
R-INL
RWB, VA = NC
Resistor Nonlinearity2
Nominal Resistance3
R
TA = +25°C, Model: AD840XYY1
VAB = VDD, Wiper = No Connect
Resistance Tempco
∆RAB/∆T
Wiper Resistance
RW
IW = 1 V/RAB
Nominal Resistance Match
∆R/RO
CH 1 to 2, VAB = VDD, TA = +25°C
DC CHARACTERISTICS POTENTIOMETER DIVIDER Specifications Apply to All VRs
Resolution
N
INL
Integral Nonlinearity4
Differential Nonlinearity4
DNL
VDD = +5 V
DNL
VDD = +3 V, TA = +25°C
Voltage Divider Temperature Coefficent ∆VW/∆T
Code = 80H
Code = FFH
Full-Scale Error
VWFSE
Zero-Scale Error
VWZSE
Code = 00H
RESISTOR TERMINALS
Voltage Range5
Capacitance6 Ax, Bx
Capacitance6 Wx
Shutdown Supply Current7
Shutdown Wiper Resistance
VA, B, W
CA, B
CW
IDD_SD
RW_SD
DIGITAL INPUTS & OUTPUTS
Input Logic High
Input Logic Low
Input Logic High
Input Logic Low
Output Logic High
Output Logic Low
Input Current
Input Capacitance6
VIH
VIL
VIH
VIL
VOH
VOL
IIL
CIL
POWER SUPPLIES
Power Supply Range
Supply Current (CMOS)
Supply Current (TTL)8
Power Dissipation (CMOS)9
Power Supply Sensitivity
DYNAMIC CHARACTERISTICS6, 10
Bandwidth –3 dB
Total Harmonic Distortion
VW Settling Time
Resistor Noise Voltage
Crosstalk11
Min
Typ1
Max
Units
–5
–4
0.8
–1
± 1.5
1.2
700
53
0.75
+3
+4
1.5
LSB
LSB
kΩ
ppm/°C
Ω
%
±2
–1.5
–2
25
–12
6
+6
+2
+5
8
–6
–4
–5
–20
0
0
f = 1 MHz, Measured to GND, Code = 80H
f = 1 MHz, Measured to GND, Code = 80H
VA = VDD, VB = 0 V, SHDN = 0
VA = VDD, VB = 0 V, SHDN = 0, VDD = +5 V
VDD = +5 V
VDD = +5 V
VDD = +3 V
VDD = +3 V
RL = 1 kΩ to VDD
IOL = 1.6 mA, VDD = +5 V
VIN = 0 V or +5 V, VDD = +5 V
100
2
0
10
VDD
75
120
0.01
50
5
100
2.4
V
pF
pF
µA
Ω
5
V
V
V
V
V
V
µA
pF
0.8
2.1
0.6
VDD–0.1
0.4
±1
2.7
Bits
LSB
LSB
LSB
ppm/°C
LSB
LSB
VDD Range
IDD
IDD
PDISS
PSS
PSS
VIH = VDD or VIL = 0 V
VIH = 2.4 V or 0.8 V, VDD = +5.5 V
VIH = VDD or VIL = 0 V, VDD = +5.5 V
∆VDD = +5 V ± 10%
∆VDD = +3 V ± 10%
5.5
5
4
27.5
0.0035 0.008
0.05
0.13
V
µA
mA
µW
%/%
%/%
BW_1K
THDW
tS
eNWB
CT
R = 1 kΩ
VA = 1 V rms + 2 V dc, VB = 2 V dc, f = 1 kHz
VA = VDD, VB = 0 V, ± 1% Error Band
RWB = 500 Ω, f = 1 kHz, RS = 0
VA = VDD, VB = 0 V
5,000
0.015
0.5
3
–65
kHz
%
µs
nV/√Hz
dB
0.01
0.9
NOTES FOR 1 kΩ VERSION
1
Typicals represent average readings at +25°C and VDD = +5 V.
2
Resistor position nonlinearity error R-INL is the deviation from an ideal value measured between the maximum resistance and the minimum resistance wiper
positions. R-DNL measures the relative step change from ideal between successive tap positions. See Figure 30 test circuit.
IW = 500 µA for VDD = +3 V and IW = 4 mA for VDD = +5 V for 1 kΩ version.
3
VAB = VDD, Wiper (VW) = No Connect.
4
INL and DNL are measured at V W with the RDAC configured as a potentiometer divider similar to a voltage output D/A converter. V A = VDD and VB = 0 V.
DNL Specification limits of ± 1 LSB maximum are Guaranteed Monotonic operating conditions. See Figure 29 test circuit.
5
Resistor terminals A, B, W have no limitations on polarity with respect to each other.
6
Guaranteed by design and not subject to production test. Resistor-terminal capacitance tests are measured with 2.5 V bias on the measured terminal. The remaining
resistor terminals are left open circuit.
7
Measured at the Ax terminals. All Ax terminals are open circuited in shutdown mode.
8
Worst case supply current consumed when input logic level at 2.4 V, standard characteristic of CMOS logic. See Figure 21 for a plot of I DD versus logic voltage.
9
PDISS is calculated from (I DD × VDD). CMOS logic level inputs result in minimum power dissipation.
10
All Dynamic Characteristics use V DD = +5 V.
11
Measured at a VW pin where an adjacent V W pin is making a full-scale voltage change.
Specifications subject to change without notice.
–4–
REV. B
AD8400/AD8402/AD8403–SPECIFICATIONS
All VERSIONS
(V = +3 V 6 10% or + 5 V 6 10%, V = +V
ELECTRICAL CHARACTERISTICS otherwise noted)
DD
Parameter
DD,
A
VB = 0 V, –408C ≤ TA ≤ +858C unless
Symbol
Conditions
Min
tCH, tCL
tDS
tDH
tPD
tCSS
tCSW
tRS
tCSH
tCS1
Clock Level High or Low
10
5
5
1
10
10
50
0
10
Typ1
Max
Units
2, 3
SWITCHING CHARACTERISTICS
Input Clock Pulse Width
Data Setup Time
Data Hold Time
CLK to SDO Propagation Delay4
CS Setup Time
CS High Pulse Width
Reset Pulse Width
CLK Fall to CS Rise Hold Time
CS Rise to Clock Rise Setup
RL = 1 kΩ to +5 V, CL ≤ 20 pF
25
ns
ns
ns
ns
ns
ns
ns
ns
ns
NOTES
1
Typicals represent average readings at +25°C and VDD = +5 V.
2
Guaranteed by design and not subject to production test. Resistor-terminal capacitance tests are measured with 2.5 V bias on the measured terminal. The remaining
resistor terminals are left open circuit.
3
See timing diagram for location of measured values. All input control voltages are specified with t R = tF = 1 ns (10% to 90% of V DD) and timed from a voltage level
of 1.6 V. Switching characteristics are measured using V DD = +3 V or +5 V. To avoid false clocking a minimum input logic slew rate of 1 V/ µs should be maintained.
4
Propagation Delay depends on value of V DD, RL and CL–see applications text.
Specifications subject to change without notice.
1
A1
SDI
A0
D7
D6
D5
D4
D3
D2
D1
tRS
1
D0
RS
0
0
1
tS
CLK
0
VOUT
VDD
VDD/2
DAC REGISTER LOAD
1
±1%
±1% ERROR BAND
CS
0
VOUT
VDD
Figure 1c. Reset Timing Diagram
0V
ABSOLUTE MAXIMUM RATINGS*
(TA = +25°C, unless otherwise noted)
Figure 1a. Timing Diagram
SDI
(DATA IN)
SDO
(DATA OUT)
VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V, +8 V
VA, VB, VW to GND . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V, VDD
AX–BX, AX–WX, BX–WX . . . . . . . . . . . . . . . . . . . . . . ± 20 mA
Digital Input and Output Voltage to GND . . . . . . . 0 V, +8 V
Operating Temperature Range . . . . . . . . . . . . –40°C to +85°C
Maximum Junction Temperature (TJ max) . . . . . . . . . +150°C
Storage Temperature . . . . . . . . . . . . . . . . . . –65°C to +150°C
Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . . . +300°C
Package Power Dissipation . . . . . . . . . . . . . . (TJ max–TA)/θJA
Thermal Resistance (θJA)
P-DIP (N-14) . . . . . . . . . . . . . . . . . . . . . . . . . . . . +83°C/W
P-DIP (N-24) . . . . . . . . . . . . . . . . . . . . . . . . . . . . +63°C/W
SOIC (SO-14) . . . . . . . . . . . . . . . . . . . . . . . . . . . +70°C/W
SOIC (SOL-24) . . . . . . . . . . . . . . . . . . . . . . . . . +120°C/W
TSSOP-14 (RU-14) . . . . . . . . . . . . . . . . . . . . . . +180°C/W
TSSOP-24 (RU-24) . . . . . . . . . . . . . . . . . . . . . . +143°C/W
1
Ax OR Dx
Ax OR Dx
0
tDS
tDH
1
A'x OR D'x
A'x OR D'x
0
tPD_MIN
tPD_MAX
tCH
1
tCS1
CLK
0
1
tCSS
tCL
tCSH
tCSW
CS
0
tS
VDD
VOUT
0V
±1 %
±1 % ERROR BAND
*Stresses above those listed under “Absolute Maximum Ratings” may cause
permanent damage to the device. This is a stress rating only; functional operation
of the device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
Figure 1b. Detail Timing Diagram
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD8400/AD8402/AD8403 feature proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore,
proper ESD precautions are recommended to avoid performance degradation or loss of functionality.
–5–
WARNING!
ESD SENSITIVE DEVICE
REV. B
AD8400/AD8402/AD8403
ORDERING GUIDE
Table I. Serial Data Word Format
Model
#CHs/
kV
Temperature
Range
Package
Package
Description Option*
ADDR
B9
B8
B7
AD8400AN10
AD8400AR10
AD8402AN10
AD8402AR10
AD8402ARU10
AD8403AN10
AD8403AR10
AD8403ARU10
X1/10
X1/10
X2/10
X2/10
X2/10
X4/10
X4/10
X4/10
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
PDIP-8
SO-8
PDIP-14
SO-14
TSSOP-14
PDIP-24
SOIC-24
TSSOP-24
N-8
SO-8
N-14
SO-14
RU-14
N-24
SOL-24
RU-24
A1
MSB
29
D7 D6
MSB
27
AD8400AN50
AD8400AR50
AD8402AN50
AD8402AR50
AD8403AN50
AD8403AR50
X1/50
X1/50
X2/50
X2/50
X4/50
X4/50
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
PDIP-8
SO-8
PDIP-14
SO-14
PDIP-24
SOIC-24
N-8
SO-8
N-14
SO-14
N-24
SOL-24
AD8400AN100
AD8400AR100
AD8402AN100
AD8402AR100
AD8402ARU100
AD8403AN100
AD8403AR100
AD8403ARU100
X1/100
X1/100
X2/100
X2/100
X2/100
X4/100
X4/100
X4/100
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
PDIP-8
SO-8
PDIP-14
SO-14
TSSOP-14
PDIP-24
SOIC-24
TSSOP-24
N-8
SO-8
N-14
SO-14
RU-14
N-24
SOL-24
RU-24
AD8400AN1
AD8400AR1
AD8402AN1
AD8402AR1
AD8403AN1
AD8403AR1
AD8403ARU1
X1/1
X1/1
X2/1
X2/1
X4/1
X4/1
X4/1
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
PDIP-8
SO-8
PDIP-14
SO-14
PDIP-24
SOIC-24
TSSOP-24
N-8
SO-8
N-14
SO-14
N-24
SOL-24
RU-24
A0
LSB
28
B6
DATA
B5 B4
B3
B2
B1
B0
D5
D3
D2
D1
D0
LSB
20
D4
PIN CONFIGURATIONS
8 A1
B1 1
AD8400
7 W1
TOP VIEW
CS 3 (Not to Scale) 6 VDD
GND 2
5 CLK
SDI 4
AGND 1
14 B1
B2 2
13 A1
A2 3
AD8402
12 W1
DGND 5
TOP VIEW 11 VDD
(Not to Scale)
10 RS
SHDN 6
9 CLK
W2 4
CS 7
8 SDI
AGND2 1
24 B1
B2 2
23 A1
A2 3
22 W1
W2 4
AGND4 5
21 AGND1
AD8403
20 B3
B4 6
TOP VIEW 19 A3
A4 7 (Not to Scale) 18 W3
*N = Plastic DIP; SO = Small Outline; RU = Thin Shrink SO.
The AD8400, AD8402 and the AD8403 contain 720 transistors.
W4 8
–6–
17 AGND3
DGND 9
16 VDD
SHDN 10
15 RS
CS 11
14 CLK
SDI 12
13 SDO
REV. B
AD8400/AD8402/AD8403
AD8400 PIN DESCRIPTIONS
AD8403 PIN DESCRIPTIONS
Pin
Name
Description
Pin
Name
Description
1
2
3
B1
GND
CS
4
5
6
SDI
CLK
VDD
7
W1
Terminal B RDAC
Ground
Chip Select Input, Active Low. When CS
returns high data in the serial input register is
loaded into the DAC register.
Serial Data Input
Serial Clock Input, positive edge triggered
Positive power supply, specified for operation
at both +3 V and +5 V.
Wiper RDAC, addr = 002
1
2
3
4
5
6
7
8
9
10
AGND2
B2
A2
W2
AGND4
B4
A4
W4
DGND
SHDN
8
A1
Terminal A RDAC
11
CS
12
13
SDI
SDO
14
15
CLK
RS
16
VDD
17
18
19
20
21
22
23
24
AGND3
W3
A3
B3
AGND1
W1
A1
B1
Analog Ground #2*
Terminal B RDAC #2
Terminal A RDAC #2
Wiper RDAC #2, addr = 012
Analog Ground #4*
Terminal B RDAC #4
Terminal A RDAC #4
Wiper RDAC #4, addr = 112
Digital Ground*
Active Low Input. Terminal A open circuit.
Shutdown controls variable resistors #1
through #4
Chip Select Input, Active Low. When CS
returns high data in the serial input register
is decoded based on the address bits and
loaded into the target DAC register.
Serial Data Input
Serial Data Output, Open Drain transistor
requires pull-up resistor
Serial Clock Input, positive edge triggered
Active low reset to midscale; sets RDAC
registers to 80H
Positive power supply, specified for
operation at both +3 V and +5 V
Analog Ground #3*
Wiper RDAC #3, addr = 102
Terminal A RDAC #3
Terminal B RDAC #3
Analog Ground #1*
Wiper RDAC #1, addr = 002
Terminal A RDAC #1
Terminal B RDAC #1
AD8402 PIN DESCRIPTIONS
Pin
Name
Description
1
2
3
4
5
6
AGND
B2
A2
W2
DGND
SHDN
Analog Ground*
Terminal B RDAC #2
Terminal A RDAC #2
Wiper RDAC #2, Addr = 012
Digital Ground*
Terminal A open circuit. Shutdown controls
Variable Resistors #1 and #2
Chip Select Input, Active Low. When CS
returns high data in the serial input register is
decoded based on the address bits and loaded
into the target DAC register.
Serial Data Input
Serial Clock Input, positive edge triggered
Active low reset to midscale; sets RDAC
registers to 80H
Positive power supply, specified for operation
at both +3 V and +5 V
Wiper RDAC #1, addr = 002
Terminal A RDAC #1
Terminal B RDAC #1
7
CS
8
9
10
SDI
CLK
RS
11
VDD
12
13
14
W1
A1
B1
*All AGNDs must be connected to DGND.
*All AGNDs must be connected to DGND.
REV. B
–7–
AD8400/AD8402/AD8403–Typical Performance Characteristics
10
5
VDD = +3V OR +5V
6
4
RWB
48
40H
FREQUENCY
VWB VOLTAGE – V
4
2
SS = 184 UNITS
VDD = 4.5V
TA = +25°C
FFH
8
RESISTANCE – kΩ
60
80H
20H
3
CODE = 10H
2
1
RWA
05H
36
24
12
TA = +25°C
VDD = +5V
0
32
64
96 128 160 192 224
CODE – Decimal
0
0
256
Figure 2. Wiper to End Terminal
Resistance vs. Code
2
3
4
5
IWA CURRENT – mA
6
10
RAB (END-TO-END)
TA = +25°C
FREQUENCY
TA = +85°C
0
TA = –40°C
TA = +25°C
36
24
–0.5
12
0
64
96 128 160 192 224
32
DIGITAL INPUT CODE – Decimal
0
256
Figure 6. 10 kΩ Wiper-ContactResistance Histogram
48
0.5
TA = +25°C
TA = –40°C
0
–0.5
TA = +85°C
0
32
64
96 128 160 192 224
DIGITAL INPUT CODE – Decimal
Figure 8. Potentiometer Divider
Nonlinearity Error vs. Code
SS = 184 UNITS
VDD = 4.5V
TA = +25°C
36
24
12
256
0
35 37
39
41 43
45
47
49 51
53
55
WIPER RESISTANCE – Ω
Figure 9. 50 kΩ Wiper-ContactResistance Histogram
–8–
6
RWB (WIPER-TO-END)
4
CODE = 80H
2
100
125
Figure 7. Nominal Resistance vs.
Temperature
POTENTIOMETER MODE TEMPCO – ppm/C°
60
VDD = +5V
FREQUENCY
INL NONLINEARITY ERROR – LSB
1
8
0
25
50
75
–75 –50 –25 0
TEMPERATURE – °C
40.0 42.5 45.0 47.5 50.0 52.5 55.0 57.5 60.0 62.5 65.0
WIPER RESISTANCE – Ω
Figure 5. Resistance Step Position
Nonlinearity Error vs. Code
–1
Figure 4. 100 kΩ Wiper-ContactResistance Histogram
SS = 1205 UNITS
VDD = 4.5V
48
0.5
40.0 42.5 45.0 47.5 50.0 52.5 55.0 57.5 60.0 62.5 65.0
WIPER RESISTANCE – Ω
60
VDD = +5V
–1
0
7
Figure 3. Resistance Linearity vs.
Conduction Current
1
R-INL ERROR – LSB
1
NOMINAL RESISTANCE – Ω
0
70
VDD = +5V
TA = –40°C/+85°C
60
VA = 2.00V
50
VB = 0V
40
30
20
10
0
–10
0
32
64
96 128 160 192 224 256
CODE – DECIMAL
Figure 10. DVWB /DT Potentiometer
Mode Tempco
REV. B
AD8400/AD8402/AD8403
6
VDD = +5V
TA = –40°C/+85°C
600
80
–6
VA = NO CONNECT
500
CODE = FF
0
RWB MEASURED
400
300
200
20
–18
10
–24
08
–30
04
–36
CS
(5V/DIV)
100
40
–12
RW
(20mV/DIV)
GAIN – dB
RHEOSTAT MODE TEMPCO – ppm/C°
700
02
–42
0
01
TA = +25°C
–48
SEE TEST FIGURE 33
–100
0
32
–54
96 128 160 192 224 256
CODE – DECIMAL
64
Figure 11. DRWB /DT Rheostat Mode
Tempco
TIME 500ns/DIV
Figure 12. One Position Step Change
at Half-Scale (Code 7FH to 80H)
1k
10k
100k
FREQUENCY – Hz
CODE = FFH
0
VDD = +5V
–6
SS = 158 UNITS
GAIN – dB
AVG
0
80H
–12
OUTPUT
AVG + 2 SIGMA
0.25
–0.25
40H
–18
20H
–24
10H
–30
08H
–36
AVG – 2 SIGMA
04H
–42
INPUT
–0.5
02H
–48
–0.75
0
100
200
300
400
500
HOURS OF OPERATION AT 150°C
1k
6
FILTER = 22kHz
VDD = +5V
80H
–6
TA = +25°C
40H
GAIN – dB
–12
VOUT
(50mV/DIV)
SEE TEST CIRCUIT FIGURE 32
20H
–18
10H
–24
08H
–30
04H
–36
02H
0.01
–42
SEE TEST CIRCUIT FIGURE 31
01H
–48
–54
100
1k
10k
FREQUENCY – Hz
100k
Figure 17. Total Harmonic Distortion
Plus Noise vs. Frequency
REV. B
1M
CODE = FFH
0
0.1
0.001
10
10k
100k
FREQUENCY – Hz
Figure 16. 50 kΩ Gain vs. Frequency vs. Code
Figure 15. Large Signal Settling
Time
10
THD + NOISE – %
01H
–54
TIME = 5µs/DIV
600
Figure 14. Long-Term Drift
Accelerated by Burn-In
1
1M
6
CODE = 80H
∆RWB RESISTANCE – %
100
Figure 13. Gain vs. Frequency for
R = 10 kΩ
0.75
0.5
10
1k
TIME 200ns/DIV
Figure 18. Digital Feedthrough
vs. Time
–9–
100k
10k
FREQUENCY – Hz
1M
Figure 19. 100 kΩ Gain vs. Frequency vs. Code
AD8400/AD8402/AD8403
IDD – SUPPLY CURRENT – mA
VDD = +5V
TA = +25°C
R = 10kΩ
R = 50kΩ
10k
1k
100k
FREQUENCY – Hz
VDD = +5V
SEE TEST CIRCUIT
FIGURE 32
0
0
100
5
1
2
3
4
INPUT LOGIC VOLTAGE – Volts
0
–6
f–3dB = 71kHz, R = 100kΩ
–12
–18
f–3dB = 125kHz, R = 50kΩ
–24
VIN = 100mV rms
VDD = +5V
–30
–36
1000
800
B – VDD = 3.3V
CODE = 55H
600
C – VDD = 5.5V
CODE = FFH
400
D – VDD = 3.3V
CODE = FFH
140
VDD = +2.7V
120
100
200
1M
Figure 23. –3 dB Bandwidths
40
C
100k
1M
FREQUENCY – Hz
0
10M
Figure 24. Supply Current vs.
Clock Frequency
0
VDD = +5V
TA = +25°C
–90
WIPER SET AT
HALF-SCALE 80H
IDD – SUPPLY CURRENT –µA
PHASE – Degrees
–45
–20
1
2
3
VDD
4
6
5
1
LOGIC INPUT
VOLTAGE = 0, VDD
VDD = +5V
IA SHUTDOWN CURRENT – nA
GAIN – dB
–10
0
Figure 25. AD8403 Incremental
Wiper ON Resistance vs. VDD
100
0
SEE TEST CIRCUIT
FIGURE 36
20
D
10k
VDD = +5.5V
60
A
1k
80
B
0
100k
10k
FREQUENCY – Hz
1M
TA = +25°C
TA = +25°C
RL = 1MΩ
1k
10k
100k
FREQUENCY – Hz
160
A – VDD = 5.5V
CODE = 55H
–42
1k
Figure 22. Power Supply Rejection
vs. Frequency
RON – Ω
IDD – SUPPLY CURRENT – µA
f–3dB = 700kHz, R = 10kΩ
40
20
1200
6
VA = 4V, VB = 0V
VDD = +3V
Figure 21. Supply Current vs. Logic
Input Voltage
12
CL = 10pF
0.1
1M
Figure 20. Normalized Gain Flatness vs. Frequency
CODE = 80H
60
0.01
100
VDD = +5V DC ± 1V p-p AC
TA = +25°C
1
R = 100kΩ
10
GAIN – dB
80
TA = +25°C
PSRR – dB
NORMALIZED GAIN FLATNESS – 0.1dB/DIV
10
SEE TEST CIRCUIT 33
CODE = 80H
10
0.1
VDD = +5.5V
0.01
VDD = +3.3V
100k 200k 400k
1M
2M
4M 6M 10M
FREQUENCY – Hz
Figure 26. 1 kΩ Gain and Phase
vs. Frequency
1
–55 –35 –15
5 25 45 65 85 105 125
TEMPERATURE – °C
Figure 27. Shutdown Current vs.
Temperature
–10–
0.001
–55 –35 –15
5 25 45 65 85 105 125
TEMPERATURE – °C
Figure 28. Supply Current vs.
Temperature
REV. B
Parametric Test Circuits–AD8400/AD8402/AD8403
DUT
V+ = VDD
A
1LSB = V+/256
V+
W
B
DUT
A
B
+5V
W
~ VIN
VMS
VOUT
OP279
OFFSET
GND
2.5V DC
Figure 29. Potentiometer Divider Nonlinearity Error Test
Circuit (INL, DNL)
Figure 33. Inverting Programmable Gain Test Circuit
+5V
VOUT
NO CONNECT
OP279
IW
DUT
A
VIN
~
W
W
A
OFFSET
GND
B
VMS
B
DUT
2.5V
Figure 30. Resistor Position Nonlinearity Error (Rheostat
Operation; R-INL, R-DNL)
Figure 34. Noninverting Programmable Gain Test Circuit
IMS
+15V
A
DUT
A
V+
W
IW = 1V/RNOMINAL
VW
B
V+ ≈ VDD
VIN
VW2 – [VW1 + IW (RAWII RBW)]
RW = ––––––––––––––––––––––––––
IW
DUT
VOUT
OP42
B
OFFSET
GND
WHERE VW1 = VMS WHEN IW = 0
VMS
~
W
2.5V
AND VW2 = VMS WHEN IW = 1/R
–15V
Figure 35. Gain vs. Frequency Test Circuit
Figure 31. Wiper Resistance Test Circuit
VA
~
V+ = VDD ± 10%
W
B
RSW = 0.1V
ISW
DUT
A
PSRR (dB) = 20LOG
VMS
∆V
W
MS
( –––––
)
∆V
∆VMS%
PSS (%/%) = –––––––
∆VDD%
CODE = ØØH
→
V+
VDD
B
DD
ISW
0.1V
0 toVDD
Figure 36. Incremental ON Resistance Test Circuit
Figure 32. Power Supply Sensitivity Test Circuit (PSS,
PSRR)
REV. B
–11–
AD8400/AD8402/AD8403
OPERATION
The AD8400/AD8402/AD8403 provide a single, dual and quad
channel, 256 position digitally controlled variable resistor (VR)
device. Changing the programmed VR settings is accomplished
by clocking in a 10-bit serial data word into the SDI (Serial
Data Input) pin. The format of this data word is two address
bits, MSB first, followed by eight data bits, MSB first. Table I
provides the serial register data word format. The AD8400/
AD8402/AD8403 has the following address assignments for the
ADDR decode, which determines the location of VR latch receiving the serial register data in Bits B7 through B0:
VR# = A1 × 2 + A0 + 1
Equation 1
The single-channel AD8400 requires A1 = A0 = 0. The dualchannel AD8402 requires A1 = 0. VR settings can be changed
one at a time in random sequence. The serial clock running at
10 MHz makes it possible to load all 4 VRs in under 4 µs (10 ×
4 × 100 ns) for the AD8403. The exact timing requirements are
shown in Figures 1a, 1b and 1c.
The AD8402/AD8403 resets to midscale by asserting the RS
pin, simplifying initial conditions at power up. Both parts have a
power shutdown SHDN pin that places the VR in a zero power
consumption state where terminals Ax are open circuited and
the wiper Wx is connected to Bx resulting in only leakage currents being consumed in the VR structure. In shutdown mode
the VR latch settings are maintained so that returning to operational mode from power shutdown, the VR settings return to
their previous resistance values. The digital interface is still active in shutdown, except that SDO is deactivated. Code changes
in the registers can be made that will produce new wiper positions when the device is taken out of shutdown.
Ax
RS
SHDN
D7
D6
D5
D4
D3
D2
D1
D0
RS
RS
Wx
RDAC
LATCH
&
DECODER
RS
Bx
RS = RNOMINAL/256
Figure 37. AD8402/AD8403 Equivalent VR (RDAC) Circuit
PROGRAMMING THE VARIABLE RESISTOR
Rheostat Operation
The nominal resistance of the VR (RDAC) between terminals A
and B are available with values of 1 kΩ, 10 kΩ, 50 kΩ and 100 kΩ.
The final digits of the part number determine the nominal resistance value, e.g., 10 kΩ = 10; 100 kΩ = 100. The nominal resistance (RAB) of the VR has 256 contact points accessed by the
wiper terminal, plus the B terminal contact. The 8-bit data word
in the RDAC latch is decoded to select one of the 256 possible
settings. The wiper’s first connection starts at the B terminal for
data 00H. This B terminal connection has a wiper contact resistance of 50 Ω. The second connection (10 kΩ part) is the first
tap point located at 89 Ω [= RBA (nominal resistance)/256 + RW
= 39 Ω + 50 Ω] for data 01H. The third connection is the next
tap point representing 78 + 50 = 128 Ω for data 02H. Each LSB
data value increase moves the wiper up the resistor ladder until
the last tap point is reached at 10011 Ω. The wiper does not directly connect to the B terminal. See Figure 37 for a simplified
diagram of the equivalent RDAC circuit.
The AD8400 contains one RDAC, the AD8402 contains two
independent RDACs and the AD8403 contains four independent
RDACs. The general transfer equation that determines the digitally programmed output resistance between Wx and Bx is:
RWB (Dx) = (Dx)/256 × RBA + RW
Equation 2
where Dx is the data contained in the 8-bit RDAC# latch, and
RBA is the nominal end-to-end resistance.
For example, when VB = 0 V and A terminal is open circuit, the
following output resistance values will be set for the following
RDAC latch codes (applies to 10 kΩ potentiometers):
D
(Dec)
RWB
(Ω)
Output State
255
128
1
0
10011
5050
89
50
Full Scale
Midscale (RS = 0 Condition)
1 LSB
Zero-Scale (Wiper Contact Resistance)
Note in the zero-scale condition a finite wiper resistance of 50 Ω
is present. Care should be taken to limit the current flow between W and B in this state to a maximum value of 5 mA to
avoid degradation or possible destruction of the internal switch
contact.
Like the mechanical potentiometer the RDAC replaces, it is totally symmetrical. The resistance between the wiper W and terminal A also produces a digitally controlled resistance RWA.
When these terminals are used the B terminal should be tied to
the wiper. Setting the resistance value for RWA starts at a maximum value of resistance and decreases as the data loaded in the
RDAC latch is increased in value. The general transfer equation
for this operation is:
RWA (Dx) = (256–Dx)/256 × RBA + RW
–12–
Equation 3
REV. B
AD8400/AD8402/AD8403
where Dx is the data contained in the 8-bit RDAC# latch, and
RBA is the nominal end-to-end resistance. For example, when
VA = 0 V and B terminal is open circuit, the following output
resistance values will be set for the following RDAC latch codes
(applies to 10 kΩ potentiometers):
D
(Dec)
RWA
(Ω)
suitable means. The Figure 38 block diagrams show more detail
of the internal digital circuitry. When CS is taken active low, the
clock loads data into the 10-bit serial register on each positive
clock edge (see Table II).
VDD
CS
Output State
CLK
D7
EN
255
128
1
0
89
5050
10011
10050
Full Scale
Midscale (RS = 0 Condition)
1 LSB
Zero Scale
ADDR
DEC
A1
A0
D0
SDI
W1
B1
DI
AD8400
D0
8
GND
The wiper-to-end-terminal resistance temperature coefficient
has the best performance over the 10% to 100% of adjustment
range where the internal wiper contact switches do not contribute
any significant temperature related errors. The graph in Figure
11 shows the performance of RWB tempco vs. code, using the
trimmer with codes below 32 results in the larger temperature
coefficients plotted.
a.
AD8402
CS
CLK
ADDR
DEC
A1
A0
D0
VDD
A1
D7
EN
PROGRAMMING THE POTENTIOMETER DIVIDER
Voltage Output Operation
R
DAC
LAT
#1
W1
B1
R
D7
The digital potentiometer easily generates an output voltage
proportional to the input voltage applied to a given terminal.
For example, connecting A terminal to +5 V and B terminal to
ground produces an output voltage at the wiper starting at zero
volts up to 1 LSB less than +5 V. Each LSB of voltage is equal
to the voltage applied across terminal AB divided by the 256
position resolution of the potentiometer divider. The general
equation defining the output voltage with respect to ground for
any given input voltage applied to terminals AB is:
SDI
DI
A4
D7
10-BIT
SER
REG
D0
D0
8
W4
R
DAC
LAT
#2
B4
R
SHDN
DGND
AGND
RS
b.
Equation 4
Operation of the digital potentiometer in the divider mode results in more accurate operation over temperature. Here the
output voltage is dependent on the ratio of the internal resistors,
not the absolute value; therefore, the temperature drift improves
to 15 ppm/°C.
VDD
CS
CLK
SDO
ADDR
DEC
A1
A0
D7
DO
D0
DI
–13–
W1
B1
AD8403
A4
D7
D0
DIGITAL INTERFACING
The AD8400/AD8402/AD8403 contains a standard SPI compatible three-wire serial input control interface. The three inputs
are clock (CLK), CS and serial data input (SDI). The positiveedge sensitive CLK input requires clean transitions to avoid
clocking incorrect data into the serial input register. For best results use logic transitions faster than 1 V/µs. Standard logic
families work well. If mechanical switches are used for product
evaluation, they should be debounced by a flip-flop or other
R
DAC
LAT
#1
R
SER
REG
SDI
A1
D7
EN
At the lower wiper position settings, the potentiometer divider
temperature coefficient increases due to the contributions of the
CMOS switch wiper resistance becoming an appreciable portion
of the total resistance from terminal B to the wiper. See Figure 10
for a plot of potentiometer tempco performance versus code
setting.
REV. B
R
DAC
LAT
#1
D7
10-BIT
SER
REG
The typical distribution of RBA from channel-to-channel matches
within ± 1%. However, device-to-device matching is process lot
dependent having a ± 20% variation. The change in RBA with
temperature has a positive 500 ppm/°C temperature coefficient.
VW (Dx) = Dx/256 × VAB + VB
A1
8
D0
W4
R
DAC
LAT
#4
B4
R
SHDN
DGND
RS
AGND
c.
Figure 38. Block Diagrams
AD8400/AD8402/AD8403
Table II. Input Logic Control Truth Table
CLK CS
RS
SHDN Register Activity
L
P
H
H
H
H
X
L
L
P
H
H
X
X
H
X
H
L
H
H
X
X
H
H
P
H
H
L
AD8403
CS
No SR effect, enables SDO pin.
Shift One bit in from the SDI pin.
The tenth previously entered bit is
shifted out of the SDO pin.
Load SR data into RDAC latch
based on A1, A0 decode (Table III).
No Operation.
Sets all RDAC latches to midscale,
wiper centered, and SDO latch
cleared.
Latches all RDAC latches to 80H.
Open circuits all resistor
A–terminals, connects W to B,
turns off SDO output transistor.
RDAC 4
CLK
Figure 39. Equivalent Input Control Logic
The target RDAC latch is loaded with the last eight bits of the
serial data word completing one DAC update. In the case of the
AD8403 four separate 10-bit data words must be clocked in to
change all four VR settings.
SHDN
CS
0
1
0
1
RDAC#1
RDAC#2
RDAC#3 AD8403 Only
RDAC#4 AD8403 Only
Q
RS
Figure 40. Detail SDO Output Schematic of the AD8403
All digital pins are protected with a series input resistor and parallel Zener ESD structure shown in Figure 41a. This structure
applies to digital pins CS, SDI, SDO, RS, SHDN, CLK. The
digital input ESD protection allows for mixed power supply
applications where +5 V CMOS logic can be used to drive an
AD8400/AD8402 or AD8403 operating from a +3 V power supply. The analog pins A, B, W are protected with a 20 Ω series
resistor and parallel Zener, see Figure 41b.
1kΩ
DIGITAL
PINS
LOGIC
Figure 41a. Equivalent ESD Protection Circuits
20Ω
A, B, W
Figure 41b. Equivalent ESD Protection Circuit (Analog
Pins)
RDAC
10kΩ
A
B
CA
CW
CB
120pF
Table III. Address Decode Table
0
0
1
1
D
CK RS
The data setup and data hold times in the specification table determine the data valid time requirements. The last 10 bits of the
data word entered into the serial register are held when CS returns high. At the same time CS goes high it gates the address
decoder, which enables one of the two (AD8402) or four
(AD8403) positive edge triggered RDAC latches. See Figure 39
detail and Table III Address Decode Table.
Latch Decoded
SDO
SERIAL
REGISTER
SDI
CLK
The serial data-output (SDO) pin contains an open drain nchannel FET. This output requires a pull-up resistor in order to
transfer data to the next package’s SDI pin. The pull-up resistor
termination voltage may be larger than the VDD supply (but less
than max VDD of +8 V) of the AD8403 SDO output device,
e.g., the AD8403 could operate at VDD = 3.3 V and the pull-up
for interface to the next device could be set at +5 V. This allows
for daisy chaining several RDACs from a single processor serial
data line. The clock period needs to be increased when using a
pull-up resistor to the SDI pin of the following device in the
series. Capacitive loading at the daisy chain node SDO–SDI
between devices must be accounted for to successfully transfer
data. When daisy chaining is used, the CS should be kept low
until all the bits of every package are clocked into their respective serial registers insuring that the address bits and data bits
are in the proper decoding location. This would require 20 bits
of address and data complying to the word format provided in
Table I if two AD8403 four-channel RDACs are daisy chained.
Note, only the AD8403 has a SDO pin. During shutdown
SHDN the SDO output pin is forced to the off (logic high state)
to disable power dissipation in the pull up resistor. See Figure 40
for equivalent SDO output circuit schematic.
A0
SERIAL
REGISTER
SDI
NOTE: P = positive edge, X = don’t care, SR = shift register.
A1
RDAC 1
RDAC 2
ADDR
DECODE
CA = 90.4pF · (
DW
) + 30pF
256
CB = 90.4pF · (1 –
DW
) + 30pF
256
W
Figure 42. RDAC Circuit Simulation Model for RDAC =
10 kΩ
–14–
REV. B
AD8400/AD8402/AD8403
The ac characteristics of the RDACs are dominated by the internal parasitic capacitances and the external capacitive loads. The
–3 dB bandwidth of the AD8403AN10 (10 kΩ resistor) measures 600 kHz at half scale as a potentiometer divider. Figure 23
provides the large signal BODE plot characteristics of the three
available resistor versions 10 kΩ, 50 kΩ, and 100 kΩ. The gain
flatness versus frequency graph, Figure 26, predicts filter applications performance. A parasitic simulation model has been developed, and is shown in Figure 42. Listing I provides a macro
model net list for the 10 kΩ RDAC:
.PARAM DW=255, RDAC=10E3
*
.SUBCKT DPOT (A,W,)
*
CA
A 0 {DW/256*90.4E-12+30E-12}
RAW A W {(1-DW/256)*RDAC+50}
CW
W 0 120E-12
RBW W B {DW/256*RDAC+50}
CB
B 0 {(1-DW/256)*90.4E-12+30E-12}
*
.ENDS DPOT
The total harmonic distortion plus noise (THD+N) is measured
at 0.003% in an inverting op amp circuit using an offset ground
and a rail-to-rail OP279 amplifier, Figure 33. Thermal noise is
primarily Johnson noise, typically 9 nV/√Hz for the 10 kΩ version at f = 1 kHz. For the 100 kΩ device, thermal noise becomes
29 nV/√Hz. Channel-to-channel crosstalk measures less than
–65 dB at f = 100 kHz. To achieve this isolation, the extra ground
pins provided on the package to segregate the individual RDACs
must be connected to circuit ground. AGND and DGND pins
should be at the same voltage potential. Any unused potentiometers in a package should be connected to ground. Power supply rejection is typically –35 dB at 10 kHz (care is needed to
minimize power supply ripple in high accuracy applications).
256
224
DIGITAL CODE – Decimal
Listing I. Macro Model Net List for RDAC
Certain boundary conditions must be satisfied for proper
AD8400/AD8402/AD8403 operation. First, all analog signals
must remain within the 0 to VDD range used to operate the
single-supply AD8400/AD8402/AD8403 products. For standard
potentiometer divider applications, the wiper output can be
used directly. For low resistance loads, buffer the wiper with a
suitable rail-to-rail op amp such as the OP291 or the OP279.
Second, for ac signals and bipolar dc adjustment applications, a
virtual ground will generally be needed. Whatever method is
used to create the virtual ground, the result must provide the
necessary sink and source current for all connected loads, including adequate bypass capacitance. Figure 33 shows one
channel of the AD8402 connected in an inverting programmable gain amplifier circuit. The virtual ground is set at +2.5 V
which allows the circuit output to span a ± 2.5 volt range with
respect to virtual ground. The rail-to-rail amplifier capability is
necessary for the widest output swing. As the wiper is adjusted
from its midscale reset position (80H) toward the A terminal
(code FFH), the voltage gain of the circuit is increased in successfully larger increments. Alternatively, as the wiper is adjusted toward the B terminal (code 00H), the signal becomes
attenuated. The plot in Figure 43 shows the wiper settings for a
100:1 range of voltage gain (V/V). Note the ± 10 dB of pseudologarithmic gain around 0 dB (1 V/V). This circuit is mainly
useful for gain adjustments in the range of 0.14 V/V to 4 V/V;
beyond this range the step sizes become very large and the resistance of the driving circuit can become a significant term in the
gain equation.
APPLICATIONS
The digital potentiometer (RDAC) allows many of the applications of trimming potentiometers to be replaced by a solid-state
solution offering compact size, freedom from vibration, shock
and open contact problems encountered in hostile environments. A major advantage of the digital potentiometer is its
programmability. Any settings can be saved for later recall in
system memory.
160
128
96
64
32
0
0.1
1.0
10
INVERTING GAIN – V/V
Figure 43. Inverting Programmable Gain Plot
The two major configurations of the RDAC include the
potentiometer divider (basic 3-terminal application) and the
rheostat (2-terminal configuration) connections shown in
Figures 29 and 30.
REV. B
192
–15–
AD8400/AD8402/AD8403
40
ACTIVE FILTER
10k
RDAC4
0
–20
–40
–80
20
100
1k
10k
FREQUENCY – Hz
100k 200k
Figure 45. Programmed Center Frequency Bandpass
Response
40
–19.01
0.01µF
2.00000 k
20
0.01µF
~
B RDAC1
A1
B
A2
A3
RDAC3
±
LOWPASS
B
RDAC2
2.5V
OP279 × 2
A4
BANDPASS
Figure 44. Programmable State Variable Active Filter
AMPLITUDE – dB
VIN
20.0000 k
–60
HIGHPASS
10k
B
–0.16
20
AMPLITUDE – dB
One of the standard circuits used to generate a low-pass, highpass or bandpass filter is the state variable active filter. The digital potentiometer allows full programmability of the frequency,
gain and Q of the filter outputs. Figure 44 shows the filter circuit using a +2.5 V virtual ground, which allows a ± 2.5 VP input
and output swing. RDAC2 and 3 set the LP, HP and BP cutoff
and center frequencies respectively. These variable resistors
should be programmed with the same data (as with ganged potentiometers) to maintain the best circuit Q. Figure 45 shows
the measured filter response at the bandpass output as a function of the RDAC2 and RDAC3 settings which produce a range
of center frequencies from 2 kHz to 20 kHz. The filter gain response at the bandpass output is shown in Figure 46. At a center frequency of 2 kHz, the gain is adjusted over a –20 dB to
+20 dB range determined by RDAC1. Circuit Q is adjusted by
RDAC4. For more detailed reading on the state variable active
filter, see Analog Devices’ application note, AN-318.
0
–20
–40
–60
–80
20
100
1k
10k
FREQUENCY – Hz
100k 200k
Figure 46. Programmed Amplitude Bandpass Response
–16–
REV. B
AD8400/AD8402/AD8403
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm)
8-Pin Plastic DIP (N-8)
8-Lead SOIC (SO-8)
0.1968 (5.00)
0.1890 (4.80)
0.430 (10.92)
0.348 (8.84)
8
5
0.280 (7.11)
0.240 (6.10)
1
0.1574 (4.00)
0.1497 (3.80)
4
0.210 (5.33)
MAX
SEATING
PLANE
14-Pin Plastic DIP Package (N-14)
14
0.0500 0.0192 (0.49)
(1.27) 0.0138 (0.35)
BSC
0.0098 (0.25)
0.0075 (0.19)
8°
0°
0.0500 (1.27)
0.0160 (0.41)
14-Pin Narrow Body SOIC Package (SO-14)
14
0.280 (7.11)
0.240 (6.10)
1
7
8
0.1574 (4.00)
0.1497 (3.80)
PIN 1
7
1
0.325 (8.25)
0.300 (7.62)
0.795 (20.19)
0.725 (18.42)
0.060 (1.52)
0.015 (0.38)
0.210
(5.33)
MAX
0.130
(3.30)
MIN
0.160 (4.06)
0.115 (2.93)
0.100
(2.54)
BSC
0.070 (1.77)
0.045 (1.15)
0.0196 (0.50)
x 45 °
0.0099 (0.25)
0.0688 (1.75)
0.0532 (1.35)
0.015 (0.381)
0.008 (0.204)
0.0098 (0.25)
0.0040 (0.10)
SEATING
PLANE
0.0500
(1.27)
BSC
0.201 (5.10)
0.193 (4.90)
8
0.256 (6.50)
0.246 (6.25)
0.177 (4.50)
0.169 (4.30)
14
1
7
PIN 1
0.006 (0.15)
0.002 (0.05)
SEATING
PLANE
0.2440 (6.20)
0.2284 (5.80)
0.3444 (8.75)
0.3367 (8.55)
0.195 (4.95)
0.115 (2.93)
14-Lead TSSOP
(RU-14)
REV. B
0.0196 (0.50)
x 45°
0.0099 (0.25)
8
PIN 1
0.022 (0.558)
0.014 (0.356)
0.2440 (6.20)
0.2284 (5.80)
0.0688 (1.75)
0.0532 (1.35)
0.0098 (0.25)
0.0040 (0.10)
0.015 (0.381)
0.008 (0.204)
SEATING
PLANE
0.022 (0.558) 0.100 0.070 (1.77)
0.014 (0.356) (2.54) 0.045 (1.15)
BSC
4
PIN 1
0.195 (4.95)
0.115 (2.93)
0.130
(3.30)
MIN
0.160 (4.06)
0.115 (2.93)
5
1
0.325 (8.25)
0.300 (7.62)
0.060 (1.52)
0.015 (0.38)
PIN 1
8
0.0433
(1.10)
MAX
0.0256
(0.65)
BSC
0.0118 (0.30)
0.0075 (0.19)
0.0079 (0.20)
0.0035 (0.090)
–17–
8°
0°
0.028 (0.70)
0.020 (0.50)
0.0192 (0.49)
0.0138 (0.35)
0.0098 (0.25)
0.0075 (0.19)
8°
0°
0.0500 (1.27)
0.0160 (0.41)
AD8400/AD8402/AD8403
24-Pin Narrow Body Plastic DIP Package (N-24)
24
13
1
12
0.280 (7.11)
0.240 (6.10)
PIN 1
1.275 (32.30)
1.125 (28.60)
0.325 (8.25)
0.300 (7.62)
0.015
(0.38)
MIN
0.210
(5.33)
MAX
0.195 (4.95)
0.115 (2.93)
0.130
(3.30)
MIN
0.160 (4.06)
0.115 (2.92)
0.022 (0.558)
0.014 (0.356)
0.070 (1.77)
0.045 (1.15)
0.100 (2.54)
BSC
SEATING
PLANE
0.015 (0.381)
0.008 (0.203)
24-Pin SOIC Package (SOL-24)
24
13
0.2992 (7.60)
0.2914 (7.40)
0.4193 (10.65)
0.3937 (10.00)
PIN 1
12
1
0.1043 (2.65)
0.0926 (2.35)
0.6141 (15.60)
0.5985 (15.20)
0.0118 (0.30)
0.0040 (0.10)
0.0500
(1.27)
BSC
0.0192 (0.49)
0.0138 (0.35)
0.0125 (0.32)
0.0091 (0.23)
0.0291 (0.74)
x 45 °
0.0098 (0.25)
8°
0°
0.0500 (1.27)
0.0157 (0.40)
24-Lead Thin Surface Mount TSSOP Package (RU-24)
0.311 (7.90)
0.303 (7.70)
0.256 (6.50)
1
0.006 (0.15)
12
PIN 1
0.0433
(1.10)
MAX
0.002 (0.05)
SEATING
PLANE
0.246 (6.25)
13
0.169 (4.30)
0.177 (4.50)
24
0.0256 (0.65)
BSC
0.0118 (0.30)
0.0075 (0.19)
–18–
0.0079 (0.20)
8°
0°
0.028 (0.70)
0.020 (0.50)
0.0035 (0.090)
REV. B
–19–
–20–
PRINTED IN U.S.A.
C1997b–12–1/97
Similar pages