Kemet C0603C3331RAC Surface mount ceramic chip capacitors extended values 0603, x7r dielectric, 100 & 200 volt Datasheet

New Product Release
Surface Mount Ceramic Chip Capacitors
Extended Values 0603, X7R Dielectric, 100 & 200 Volts
100 Volts – 12,000 pF - 39,000 pF
200 Volts – 1,200 pF - 10,000 pF
Outline Drawings
Table 1 - Dimensions - Millimeters
EIA
Metric Size
Size Code Code (Ref)
0603*
1608
L#
Length
W#
Width
Thickness
B
Bandwidth
S
Min. Separation
Mounting
Technique
1.6 (.063) ± 0.15 (.006)
0.8 (.032) ± 0.15 (.006)
See Table 2
0.35 (.014) ± 0.15 (.006)
0.7 (.028)
Solder Wave or
Solder Reflow
Table 2 - Ratings & Part Number Listing
Cap Values
KEMET Part Number
Capacitance Tolerance
Thickness - mm
Qty 7” Reel
Qty 13” Reel
12,000pF
C0603C123(1)1RAC
J,K,M
0.8 ± 0.1
4,000
10,000
15,000pF
C0603C153(1)1RAC
J,K,M
0.8 ± 0.1
4,000
10,000
18,000pF
C0603C183(1)1RAC
J,K,M
0.8 ± 0.1
4,000
10,000
22,000pF
C0603C223(1)1RAC
J,K,M
0.8 ± 0.1
4,000
10,000
27,000pF
C0603C273(1)1RAC
J,K,M
0.8 ± 0.1
4,000
10,000
33,000pF
C0603C333(1)1RAC
J,K,M
0.8 ± 0.1
4,000
10,000
39,000pF
C0603C393(1)1RAC
J,K,M
0.8 ± 0.1
4,000
10,000
1,200pF
C0603C122(1)2RAC
J,K,M
0.8 ± 0.1
4,000
10,000
1,500pF
C0603C152(1)2RAC
J,K,M
0.8 ± 0.1
4,000
10,000
1,800pF
C0603C182(1)2RAC
J,K,M
0.8 ± 0.1
4,000
10,000
2,200pF
C0603C222(1)2RAC
J,K,M
0.8 ± 0.1
4,000
10,000
2,700pF
C0603C272(1)2RAC
J,K,M
0.8 ± 0.1
4,000
10,000
3,300pF
C0603C332(1)2RAC
J,K,M
0.8 ± 0.1
4,000
10,000
3,900pF
C0603C392(1)2RAC
J,K,M
0.8 ± 0.1
4,000
10,000
4,700pF
C0603C472(1)2RAC
J,K,M
0.8 ± 0.1
4,000
10,000
5,600pF
C0603C562(1)2RAC
J,K,M
0.8 ± 0.1
4,000
10,000
6,800pF
C0603C682(1)2RAC
J,K,M
0.8 ± 0.1
4,000
10,000
8,200pF
C0603C822(1)2RAC
J,K,M
0.8 ± 0.1
4,000
10,000
10,000pF
C0603C103(1)2RAC
J,K,M
0.8 ± 0.1
4,000
10,000
To complete the KEMET part number, insert capacitance tolerance: J - ±5%, K - ±10% or M ±20%.
F3272 02/05
Electrical Parameters
As detailed in the KEMET Surface Mount Catalog F3102 for X7R, with following specific requirements based on
room temperature (25°C) parameters:
• Operating Range: -55°C to +125°C, with no-bias capacitance shift limited to ± 15% over that range
• Insulation Resistance (IR) measured after 2 minutes at rated voltage @ 25°C: Limit is 1000
megohm microfarads or 100 gigohms, whichever is less.
• Capacitance and Dissipation Factor (DF) measured at 1KHz at 1.0Vrms.
25 Volts - DF Limit is 3.5%
>25 Volts - DF Limit is 2.5%.
Soldering Process
Wave soldering or reflow soldering is acceptable for these chips.
Marking
These chips are normally supplied unmarked. If required, they can be laser marked as an extra cost option.
More detail on the marking format is included in our Surface Mount Catalog F3102.
In general, the information in the KEMET Surface Mount catalog F3102 applies to these capacitors. The information in
this bulletin supplements that in the catalog.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • (864) 963-6300 • www.kemet.com
Similar pages