CY28341 Universal Single-Chip Clock Solution for VIA P4M266/KM266 DDR Systems Features FS(3:0) 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1100 1111 Supports VIA P4M266/KM266 chipsets Supports Pentium® 4, Athlon™ processors Supports two DDR DIMMS Supports three SDRAMS DIMMS at 100 MHz Provides: — Two different programmable CPU clock pairs — Six differential SDRAM DDR pairs — Three low-skew/low-jitter AGP clocks — Seven low-skew/low-jitter PCI clocks — One 48M output for USB — One programmable 24M or 48M for SIO • Dial-a-Frequency™ and Dial-a-dB features • Spread Spectrum for best electromagnetic interference (EMI) reduction • Watchdog feature for systems recovery • SMBus-compatible for programmability • 56-pin SSOP and TSSOP packages VDDR XIN REF(0:1) XTAL REF0 VDDI CPUCS_T/C FS0 FS2 SELP4_K7# VDDC CPU(0:1)/CPU0D_T/C PLL1 VDDPCI PCI(3:6) FS3 FS1 PCI_F MULTSEL PCI2 PD# PCI1 VDDAGP AGP(0:2) SDATA SCLK SMBus VDD48M 48M PLL2 /2 WDEN 24_48M SRESET# VDDD FBOUT WD SELSDR_DDR Buf_IN AGP 66.80 66.80 60.00 66.67 72.00 70.00 64.00 70.00 77.00 73.33 60.00 60.00 60.00 66.67 66.67 66.67 PCI 33.40 33.40 30.00 33.33 36.00 35.00 32.00 35.00 38.50 36.67 30.00 30.00 30.00 33.33 33.33 33.33 Pin Configuration[1] Block Diagram XOUT CPU 66.80 100.00 120.00 133.33 72.00 105.00 160.00 140.00 77.00 110.00 180.00 150.00 90.00 100.00 200.00 133.33 S2D *FS0/REF0 VSSR XIN XOUT VDDAGP AGP0 *SELP4_K7/AGP1 AGP2 VSSAGP **FS1/PCI_F **SELSDR_DDR/PCI1 *MULTSEL/PCI2 VSSPCI PCI3 PCI4 VDDPCI PCI5 PCI6 VSS48M **FS3/48M **FS2/24_48M VDD48M VDD VSS IREF *PD#/SRESET# SCLK SDATA 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 VTTPWRGD#/REF1 VDDR VSSC CPUT/CPUOD_T CPUC/CPUOD_C VDDC VDDI CPUCS_C CPUCS_T VSSI FBOUT BUF_IN DDRT0/SDRAM0 DDRC0/SDRAM1 DDRT1/SDRAM2 DDRC1/SDRAM3 VDDD VSSD DDRT2/SDRAM4 DDRC2/SDRAM5 DDRT3/SDRAM6 DDRC3/SDRAM7 VDDD VSSD DDRT4/SDRAM8 DDRC4/SDRAM9 DDRT5/SDRAM10 DDRC5/SDRAM11 56 pin SSOP DDRT(0:5)/SDRAM(0,2,4,6,8,10) DDRC(0:5)/SDRAM(1,3,5,7,9,11) CONVERT C Y 283 41 • • • • • Table 1. Frequency Selection Table Note: 1. Pins marked with [*] have internal pull-up resistors. Pins marked with [**] have internal pull-down resistors. Cypress Semiconductor Corporation Document #: 38-07367 Rev. *A • 3901 North First Street • San Jose • CA 95134 • 408-943-2600 Revised December 26, 2002 CY28341 Pin Description[2] Pin Name PWR I/O Description I Oscillator Buffer Input. Connect to a crystal or to an external clock. O Oscillator Buffer Output. Connect to a crystal. Do not connect when an external clock is applied at XIN. 3 XIN 4 XOUT VDD 1 FS0/REF0 VDD 56 VTTPWRGD# VDDR I If SELP4_K7 = 1, with a P4 processor setup as CPUT/C. At power-up, VTT_PWRGD# is an input. When this input transitions to a logic LOW, the FS (3:0) and MULTSEL are latched and all output clocks are enabled. After the first HIGH to LOW transition on VTT_PWRGD#, this pin is ignored and will not effect the behavior of the device thereafter. When the VTT_PWRGD# feature is not used, please connect this signal to ground through a 10KΩ resistor. REF1 VDDR O If SELP4_K7 = 0, with an Athlon (K7) processor as CPU_OD(T:C). VTT_PWRGD# function is disabled, and the feature is ignored. This pin becomes REF1 and is a buffered copy of the signal applied at XIN. 44,42,38, DDRT VDDD 36,32,30 (0:5)/SDRAM(0,2,4,6, 8,10) O These pins are programmable through strapping pin11, SELSDR_DDR#.If SELSDR_DDR#.= 0, these pins are configured for DDR clock outputs. They are “True” copies of signal applied at Pin45, BUF_IN. In this mode, VDDD must be 2.5VIf SelSDR_DDR#.= 1, these pins are configured for SDRAM(0,2,4,6,8,10) single ended clock outputs, copies of (and in phase with) signal applied at Pin45, BUF_IN. In this mode, VDDD must be 3.3V 43,41,37 DDRC VDDD 35,31,29 (0:5)/SDRAM(1,3,5,7, 9,11) O These pins are programmable through strapping pin11, SELSDR_DDR#.If SelSDR_DDR#.= 0, these pins are configured for DDR clock outputs. They are “Complementary” copies of signal applied at Pin45, BUF_IN. In this mode, VDDD must be 2.5VIf SelSDR_DDR#.= 1, these pins are configured for SDRAM(1,3,5,7,9,11) single-ended clock outputs, copies of (and in phase with) signal applied at Pin45, BUF_IN. In this mode, VDDD must be 3.3V. I/O Power-on Bidirectional Input/Output. At power-up, FS0 is the input. When PU the power supply voltage crosses the input threshold voltage, FS0 state is latched and this pin becomes REF0, buffered copy of signal applied at XIN. 7 SELP4_K7 / AGP1 VDDAG P I/O Power-on Bidirectional Input/Output. At power-up, SELP4_K7 is the input. PU When the power supply voltage crosses the input threshold voltage, SELP4_K7 state is latched and this pin becomes AGP1 clock output. SELP4_K7 = 1, P4 mode. SELP4_K7 = 0, K7 mode. 12 MULTSEL / PCI2 VDDPCI I/O Power-on Bidirectional Input/Output. At power-up, MULTSEL is the input. PU When the power supply voltage crosses the input threshold voltage, MULTSEL state is latched and this pin becomes PCI2 clock output. MULTSEL = 0, Ioh is 4 x IREFMULTSEL = 1, Ioh is 6 x IREF. 53 CPUT/CPUOD_T VDDC O 3.3V CPU Clock outputs. This pin is programmable through strapping pin7, SELP4_K7. If SELP4_K7 = 1, this pin is configured as the CPUT Clock Output. If SELP4_K7 = 0, this pin is configured as the CPUOD_T Open Drain Clock Output. See Table 1. 52 CPUC/CPUOD_C VDDC O 3.3V CPU Clock outputs. This pin is programmable through strapping pin7, SELP4_K7. If SELP4_K7 = 1, this pin is configured as the CPUC Clock Output. If SELP4_K7 = 0, this pin is configured as the CPUOD_C Open Drain Clock Output. See Table 1. 48,49 CPUCS_T/C VDDI O 2.5V CPU Clock Outputs for Chipset. See Table 1. 14,15,17, PCI (3:6) 18 VDDPCI O PCI Clock Outputs. Are synchronous to CPU clocks. See Table 1. 10 FS1/PCI_F VDDPCI I/O Power-on Bidirectional Input/Output. At power-up, FS0 is the input. When PD the power supply voltage crosses the input threshold voltage, FS1 state is latched and this pin becomes PCI_F clock output. 20 FS3/48M VDD48M I/O Power-on Bidirectional Input/Output. At power-up, FS3 is the input. When PD the power supply voltage crosses the input threshold voltage, FS3 state is latched and this pin becomes 48M, a USB clock output. Document #: 38-07367 Rev. *A Page 2 of 21 CY28341 Pin Description[2] (continued) Pin Name PWR I/O Description 11 SELSDR_DDR#/PCI VDDPCI 1 I/O Power-on Bidirectional Input/Output. At power-up, SELSDR_DDR is the PD input. When the power supply voltage crosses the input threshold voltage, SELSDR_DDR state is latched and this pin becomes PCI clock output.SelSDR_DDR#. = 0, DDR Mode. SelSDR_DDR#. = 1, SDR Mode. 21 FS2/24_48M VDD48M I/O Power-on Bidirectional Input/Output. At power-up, FS2 is the input. When PD the power supply voltage crosses the input threshold voltage, FS2 state is latched and this pin becomes 24_48M, a SIO programmable clock output. 6 AGP0 VDDAG P O AGP Clock Output. Is synchronous to CPU clocks. See Table 1. 8 AGP2 VDDAG P O AGP Clock Output. Is synchronous to CPU clocks. See Table 1. 25 IREF I Current reference programming input for CPU buffers. A precise resistor is attached to this pin, which is connected to the internal current reference. 28 SDATA I/O Serial Data Input. Conforms to the Philips I2C specification of a Slave Receive/Transmit device. It is an input when receiving data. It is an open drain output when acknowledging or transmitting data. 27 SCLK 26 PD#/SRESET# I Serial Clock Input. Conforms to the Philips I2C specification. 45 BUF_IN If SelSDR_DDR#.= 0, 2.5V CMOS type input to the DDR differential buffers.If SelSDR_DDR#.= 1, 3.3V CMOS type input to the SDR buffer. 46 FBOUT If SelSDR_DDR#.= 0, 2.5V single ended SDRAM buffered output of the signal applied at BUF_IN. It is in phase with the DDRT(0:5) signals.If SelSDR_DDR#.= 1, 3.3V single ended SDRAM buffered output of the signal applied at BUF_IN. It is in phase with the SDRAM(0:11) signals 5 VDDAGP 3.3V Power Supply for AGP clocks 51 VDDC 3.3V Power Supply for CPUT/C clocks 16 VDDPCI 3.3V Power Supply for PCI clocks 55 VDDR 3.3V Power Supply for REF clock 50 VDDI 2.5V Power Supply for CPUCS_T/C clocks 22 VDD48M 3.3V Power Supply for 48M I/O Power-down Input/System Reset Control Output. If Byte6 Bit7 = 0, this pin PU becomes a SRESET# open drain output, and the internal pulled up is not active. See system reset description. If Byte6 Bit7 = 1 (default), this pin becomes PD# input with an internal pull-up. When PD# is asserted LOW, the device enters power-down mode. See power management function. 23 VDD 3.3V Common Power Supply 34,40 VDDD If SelSDR_DDR#.= 0, 2.5V Power Supply for DDR clocksIf SelSDR_DDR#.= 1, 3.3V Power Supply for SDR clocks. 9 VSSAGP Ground for AGP clocks 13 VSSPCI Ground for PCI clocks 54 VSSC Ground for CPUT/C clocks 33,39 VSSD Ground for DDR clocks 19 VSS48M Ground for 48M clock 47 VSSI Ground for ICPUCS_T/C clocks 24 VSS Common Ground Note: 2. PU = internal Pull-up. PD = internal Pull-down. Typically = 250 kW (range 200 kW to 500 kW). Document #: 38-07367 Rev. *A Page 3 of 21 CY28341 Serial Data Interface Data Protocol To enhance the flexibility and function of the clock synthesizer, a two-signal serial interface is provided. Through the Serial Data Interface, various device functions such as individual clock output buffers, etc., can be individually enabled or disabled. The clock driver serial protocol accepts Byte Write, Byte Read, Block Write, and Block Read operation from the controller. For Block Write/Read operation, the bytes must be accessed in sequential order from lowest to highest byte (most significant bit first) with the ability to stop after any complete byte has been transferred. For Byte Write and Byte Read operations, the system controller can access individual indexed bytes. The offset of the indexed byte is encoded in the command code, as described in Table 2. The registers associated with the Serial Data Interface initializes to their default setting upon power-up, and therefore use of this interface is optional. Clock device register changes are normally made upon system initialization, if any are required. The interface can also be used during system operation for power management functions. The Block Write and Block Read protocol is outlined in Table 3, while Table 4 outlines the corresponding Byte Write and Byte Read protocol. The slave receiver address is 11010010 (D2h). Table 2. Command Code Definition Bit 7 (6:0) Description 0 = Block Read or Block Write operation 1 = Byte Read or Byte Write operation Byte offset for Byte Read or Byte Write operation. For Block Read or Block Write operations, these bits should be “0000000” Table 3. Block Read and Block Write Protocol Bit 1 2:8 9 10 11:18 19 20:27 28 29:36 37 38:45 46 .... .... .... .... Block Write Protocol Description Start Slave address – 7 bits Write Acknowledge from slave Command Code – 8-bit “00000000” stands for Block operation Acknowledge from slave Byte Count – 8 bits Acknowledge from slave Data byte 0 – 8 bits Acknowledge from slave Data byte 1 – 8 bits Acknowledge from slave Data Byte N/Slave acknowledge... Data Byte N – 8 bits Acknowledge from slave Stop Document #: 38-07367 Rev. *A Bit 1 2:8 9 10 11:18 19 20 21:27 28 29 30:37 38 39:46 47 48:55 56 .... .... .... .... Block Read Protocol Description Start Slave address – 7 bits Write Acknowledge from slave Command Code – 8-bit “00000000” stands for Block operation Acknowledge from slave Repeat start Slave address – 7 bits Read Acknowledge from slave Byte count from slave – 8 bits Acknowledge Data byte from slave – 8 bits Acknowledge Data byte from slave – 8 bits Acknowledge Data bytes from slave/Acknowledge Data byte N from slave – 8 bits Not Acknowledge Stop Page 4 of 21 CY28341 Table 4. Byte Read and Byte Write Protocol Byte Write Protocol Byte Read Protocol Bit Description Bit Description 1 Start 1 Start 2:8 Slave address – 7 bits 2:8 Slave address – 7 bits 9 Write 9 Write 10 Acknowledge from slave 10 Acknowledge from slave 11:18 Command Code – 8 bits “1xxxxxxx” stands for byte operationbit[6:0] of the command code represents the offset of the byte to be accessed 11:18 Command Code – 8 bits “1xxxxxxx” stands for byte operationbit[6:0] of the command code represents the offset of the byte to be accessed 19 Acknowledge from slave 19 Acknowledge from slave 20:27 Byte Count – 8 bits 20 Repeat start 28 Acknowledge from slave 21:27 Slave address – 7 bits 29 Stop 28 Read 29 Acknowledge from slave 30:37 Data byte from slave – 8 bits 38 Not Acknowledge 39 Stop Serial Control Registers Byte 0: Frequency Select Register Bit @Pup Pin# Name Reserved Description 7 0 6 H/W Setting 21 FS2 Reserved 5 H/W Setting 10 FS1 For Selecting Frequencies see Table 1. 4 H/W Setting 1 FS0 For Selecting Frequencies see Table 1. 3 0 2 H/W Setting 11 1 H/W Setting 20 FS3 0 H/W Setting 7 SELP4_K7 For Selecting Frequencies see Table 1. If this bit is programmed to “1,” it enables Write to bits (6:4,1) for selecting the frequency via software (SMBus). If this bit is programmed to a “0,” it enables only Read of bits (6:4,1), which reflects the hardware setting of FS(0:3). SELSDR_DDR Only for reading the hardware setting of the SDRAM interface mode, status of SELSDR_DDR# strapping. For Selecting frequencies see Table 1. Only for reading the hardware setting of the CPU interface mode, status of SELP4_K7# strapping. Byte 1: CPU Clocks Register Bit 7 @Pup 0 Pin# Name MODE Description 0 = Down Spread. 1 = Center Spread. See Table 9. 6 5 1 SSCG 1 = Enable (default). 0 = Disable 1 SST1 Select spread bandwidth. See Table 9. 4 1 3 1 48,49 CPUCS_T, CPUCS_C 2 1 53,52 CPUT/CPUOD_T CPUC/CPUOD_C 1 1 53,52 CPUT/C In K7 mode, this bit is ignored.In P4 mode, 0 = when PD# asserted LOW, CPUT stops in a HIGH state, CPUC stops in a LOW state. In P4 mode, 1 = when PD# asserted LOW, CPUT and CPUC stop in High-Z. 0 1 11 MULT0 Only For reading the hardware setting of the Pin11 MULT0 value. SST0 Document #: 38-07367 Rev. *A Select spread bandwidth. See Table 9. 1 = output enabled (running). 0 = output disabled asynchronously in a LOW state. 1 = output enabled (running). 0 = output disable. Page 5 of 21 CY28341 Byte 2: PCI Clock Register Bit @Pup 7 0 Pin# Name Description PCI_DRV PCI clock output drive strength 0 = Normal, 1 = increase the drive strength 20%. 6 1 10 PCI_F 1 = output enabled (running). 0 = output disabled asynchronously in a LOW state. 5 1 18 PCI6 1 = output enabled (running). 0 = output disabled asynchronously in a LOW state. 4 1 17 PCI5 1 = output enabled (running). 0 = output disabled asynchronously in a LOW state. 3 1 15 PCI4 1 = output enabled (running). 0 = output disabled asynchronously in a LOW state. 2 1 14 PCI3 1 = output enabled (running). 0 = output disabled asynchronously in a LOW state. 1 1 12 PCI2 1 = output enabled (running). 0 = output disabled asynchronously in a LOW state. 0 1 11 PCI1 1 = output enabled (running). 0 = output disabled asynchronously in a LOW state. Byte 3: AGP/Peripheral Clocks Register Bit @Pup Pin# Name Description 24_48M “0” = pin21 output is 24MHz. Writing a “1” into this register asynchronously changes the frequency at pin21 to 48 MHz. 7 0 21 6 1 20 48MHz 1 = output enabled (running). 0 = output disabled asynchronously in a LOW state. 5 1 21 24_48M 1 = output enabled (running). 0 = output disabled asynchronously in a LOW state. 4 0 6,7,8 DASAG1 3 0 6,7,8 DASAG0 Programming these bits allow shifting skew of the AGP(0:2) signals relative to their default value. See Table 5. 2 1 8 AGP2 1 = output enabled (running). 0 = output disabled asynchronously in a LOW state. 1 1 7 AGP1 1 = output enabled (running). 0 = output disabled asynchronously in a LOW state. 0 1 6 AGP0 1 = output enabled (running). 0 = output disabled asynchronously in a LOW state. Table 5. Dial-a-Skew™ AGP(0:2) DASAG (1:0) AGP(0:2) Skew Shift 00 Default 01 –280 ps 10 +280 ps 11 +480 ps Byte 4: Peripheral Clocks Register Bit @Pup Pin# Name Description 7 1 20 48M 1 = normal strength, 0 = high strength 1 = normal strength, 0 = high strength 6 1 21 24_48M 1 = normal strength, 0 = high strength 1 = normal strength, 0 = high strength 5 0 6,7,8 4 0 6,7,8 DARAG1 Programming these bits allow modifying the frequency ratio of the AGP(2:0), PCI(6:1, F) clocks DARAG0 relative to the CPU clocks. See Table 6. 3 1 1 REF0 1 = output enabled (running). 0 = output disabled asynchronously in a LOW state. 2 1 56 REF1 1 = output enabled (running). 0 = output disabled asynchronously in a LOW state. (K7 Mode only.) 1 1 1 REF0 1 = normal strength, 0 = high strength 0 1 56 REF1 1 = normal strength, 0 = high strength (K7 Mode only.) Table 6. Dial-A-Ratio™ AGP(0:2) DARAG (1:0) CU/AGP Ratio 00 Frequency Selection Default 01 2/1 10 2.5/1 11 3/1 Document #: 38-07367 Rev. *A Page 6 of 21 CY28341 Byte 5: SDR/DDR Clock Register Bit @Pup Pin# Name 7 0 45 BUF_IN threshold voltage Description 6 1 46 5 1 29,30 DDRT/C5/SD 1 = output enabled (running). 0 = output disabled asynchronously in a LOW state. RAM(10,11) 4 1 31,32 DDRT/C4/SD 1 = output enabled (running). 0 = output disabled asynchronously in a LOW state. RAM(8,9) 3 1 35,36 DDRT/C3/SD 1 = output enabled (running). 0 = output disabled asynchronously in a LOW state. RAM(6,7) 2 1 37,38 DDRT/C2/SD 1 = output enabled (running). 0 = output disabled asynchronously in a LOW state. RAM(4,5) 1 1 41,42 DDRT/C1/SD 1 = output enabled (running). 0 = output disabled asynchronously in a LOW state. RAM(2,3) 0 1 43,44 DDRT/C0/SD 1 = output enabled (running). 0 = output disabled asynchronously in a LOW state. RAM(0,1) DDR Mode, BUF_IN threshold setting. 0 = 1.15V, 1 = 1.05VSDR Mode, BUF_IN threshold setting. 0 = 1.35V, 1 = 1.25V FBOUT 1 = output enabled (running). 0 = output disabled asynchronously in a LOW state. Byte 6: Watchdog Register Bit @Pup Pin# 7 1 6 0 26 Name Description SRESET# 1 = Pin 26 is the input pin as PD# signal. 0 = Pin 26 is the output pin as SRESET# signal. Frequency This bit allows setting the Revert Frequency once the system is rebooted due to Watchdog time Revert out only.0 = selects frequency of existing H/W setting1 = selects frequency of the second to last S/W setting (the software setting prior to the one that caused a system reboot). 5 0 WDTEST WD-Test, ALWAYS program to “0.” 4 0 WD Alarm This bit is set to “1” when the Watchdog times out. It is reset to “0” when the system clears the WD time stamps (WD3:0). 3 0 WD3 This bit allows the selection of the time stamp for the Watchdog timer. See Table 7. 2 0 WD2 This bit allows the selection of the time stamp for the Watchdog timer. See Table 7. 1 0 WD1 This bit allows the selection of the time stamp for the Watchdog timer. See Table 7. 0 0 WD0 This bit allows the selection of the time stamp for the Watchdog timer. See Table 7. Table 7. Watchdog Time Stamp WD3 0 WD2 0 WD1 0 WD0 0 0 0 0 1 1 second 0 0 0 0 0 0 1 1 1 1 0 0 0 1 0 1 2 seconds 3 seconds 4 seconds 5 seconds 0 1 1 0 6 seconds 0 1 1 1 7 seconds 1 0 0 0 8 seconds 1 0 0 1 9 seconds 1 0 1 0 10 seconds 1 0 1 1 11 seconds 1 1 0 0 12 seconds 1 1 0 1 13 seconds 1 1 1 1 1 1 0 1 14 seconds 15 seconds Document #: 38-07367 Rev. *A FUNCTION Off Page 7 of 21 CY28341 Byte 7: Dial-a-Frequency Control Register N Bit 7 6 5 4 3 2 1 0 @Pup 0 0 0 0 0 0 0 0 Pin# Name Reserved N6, MSB N5 N4 N3 N2 N3 N0, LSB Description Reserved for device function test. These bits are for programming the PLL’s internal N register. This access allows the user to modify the CPU frequency at very high resolution (accuracy). All other synchronous clocks (clocks that are generated from the same PLL, such as PCI) remain at their existing ratios relative to the CPU clock. Byte 8: Silicon Signature Register (All bits are Read-only) Bit 7 @Pup 0 6 Pin# Name Revision_ID3 Revision ID bit [3] Description 0 Revision_ID2 Revision ID bit [2] 5 4 0 0 Revision_ID1 Revision_ID0 Revision ID bit [1] Revision ID bit [0] 3 1 Vender_ID3 Cypress Vender ID bit [3]. 2 0 Vender_ID2 Cypress Vender ID bit [2]. 1 0 0 0 Vender_ID1 Vender_ID0 Cypress Vender ID bit [1]. Cypress Vender ID bit [0]. Byte9: Dial-A-Frequency Control Register R Bit @Pup 7 0 Pin# Name Description Reserved 6 5 0 0 R5, MSB R4 These bits are for programming the PLL’s internal R register. This access allows the user to modify the CPU frequency at very high resolution (accuracy). All other synchronous clocks (clocks that are generated from the same PLL, such as PCI) remain at their existing ratios relative to the CPU clock. 4 0 R3 3 0 R2 2 0 R1 1 0 R0 0 0 DAF_ENB This Edge-trigger bit enables the Dial-a-Frequency N and R bits. It is the transition of this bit from “0” to “1” that latches the N(6:0) and R(5:0) data into the internal N and R registers. The user must only program a one time “1” into this bit for every new N and R values Dial-a-Frequency Feature SMBus Dial-a-Frequency feature is available in this device via Byte7 and Byte9. P is a PLL constant that depends on the frequency selection prior to accessing the Dial-a-Frequency feature. Table 8. FS(4:0) XXXXX P 96016000 Spread Spectrum Clock Generation (SSCG) Spread Spectrum is enabled/disabled via SMBus register Byte 1, Bit 7. Document #: 38-07367 Rev. *A Page 8 of 21 CY28341 operation of the system in case of a hang-up due to the frequency change. Table 9. Spread Spectrum Table Mode SST1 SST0 % Spread 0 0 0 –1.5% 0 0 1 –1.0% 0 1 0 –0.7% 0 1 1 –0.5% 1 0 0 ±0.75% 1 0 1 ±0.5% 1 1 0 ±0.35% 1 1 1 ±0.25% When the system sends an SMBus command requesting a frequency change through Byte 4 or through Bytes 13 and 14, it must have previously sent a command to Byte 12, for selecting which time out stamp the Watchdog must perform, otherwise the System Self Recovery feature will not be applicable. Consequently, this device will change frequency and then the Watchdog timer starts timing. Meanwhile, the system BIOS is running its operation with the new frequency. If this device receives a new SMBus command to clear the bits originally programmed in Byte 12,Bits (3:0) (reprogram to 0000), before the Watchdog times out, then this device will keep operating in its normal condition with the new selected frequency. If the Watchdog times out the first time before the new SMBus reprograms Byte12,Bits (3:0) to (0000), then this device will send a low system reset pulse, on SRESET# (see Byte12,Bit7), and changes WD alarm (Byte12,Bit4) status to “1” then restarts the Watchdog timer again. If the Watchdog times out a second time, then this device will send another low pulse on SRESET#, will relatch original hardware strapping frequency (or second to last software selected frequency, see Byte12,Bit6) selection, set WD alarm bit (Byte12,Bit4) to “1,” then start WD timer again. The above-described sequence will keep repeating until the BIOS clears the SMBus Byte12,Bits(3:0). Once the BIOS sets Byte12,Bits(3:0) = 0000, then the Watchdog timer is turned off and the WD alarm bit (Byte12,Bit4) is reset to”0.” Swing Select Functions Through Hardware MULT- Board Target Reference R, Output SEL Trace/Term Z IREF = VDD/(3*Rr) Current VOH@Z 0 50 Ohm Rr = 221 1%, IOH = 4 * 1.0V@50 IREF = 5.00 mA Iref 1 50 Ohm Rr = 475 1%, IOH = 6 * 0.7V@50 IREF = 2.32 mA Iref System Self-recovery Clock Management This feature is designed to allow the system designer to change frequency while the system is running and reboot the S y s t e m r u n n in g w it h o rig in a lly s e le c te d fre q u e n c y v ia h a r d w a r e s tr a p p in g . N o F r e q u e n c y w ill c h a n g e b u t S y s t e m S e lf R e c o v e r y n o t a p p lic a b le ( n o t im e s t a m p s e le c t e d a n d b y t e 1 2 , b it ( 3 : 0 ) is s t ill = "0 0 0 0 " R e c e iv e F r e q u e n c y C h a n g e R e q u e s t v ia S M B u s B y t e 4 o r V ia D ia la -fre q u e n c y ? Y e s C h a n g e to a n e w fre q u e n c y N o Is S M B u s B y te 9 , tim e o u t s t a m p e n a b le d - ( b y t e 1 2 , b it (3 :0 ) 0 0 0 0 )? 1 ) S e n d a n o th e r 3 m S lo w p u ls e o n S 2 ) R e la tc h o r ig in a l h a r d w a r e s tr a p p in f o r r e t u r n t o o r ig in a l f r e q u e n c y s e t t in g 3 ) S e t W D A la r m b it ( b y t e 1 2 , B it 4 ) t o 4 ) S ta r t W D tim e r Y e s R E S E T g s e le c t io n s . "1 " S t a r t in t e r n a l w a t c h d o g t im e r . Y e s W a tc h D o g tim e o u t? 1 ) S e n d S R E S E T p u ls e 2 ) S e t W D b it ( b y t e 1 2 , b it 4 ) t o ’1 ’ 3 ) S ta r t W D tim e r Y e s W a t c h D o g t im e o u t ? N o N o S M B u s b y te 1 2 tim e o u t s ta m p d is a b le d ? N o S M B u s b y te 9 tim e o u t s ta m p d is a b le d , B y te 1 2 , b it(3 :0 ) = (0 0 0 0 ) ? N o Y e s Y e s T u r n o ff w a tc h d o g tim e r. K e e p n e w f r e q u e n c y s e t t in g . S e t W D b i t ( b y t e 1 2 , b i t 4 ) t o ’’0 ’ a la rm Figure 1. Power Management Functions All clocks can be individually enabled or stopped via the 2-wire control interface. All clocks are stopped in the LOW state. All clocks maintain a valid HIGH period on transitions from running to stop and on transitions from stopped to running Document #: 38-07367 Rev. *A when the chip was not powered down. On power-up, the VCOs will stabilize to the correct pulse widths within about 0.5 mS. Page 9 of 21 CY28341 Maximum Ratings[3] This device contains circuitry to protect inputs against damage due to high-static voltages or electric field. However, precautions should be take to avoid application of any voltage higher than the maximum-rated voltages to this circuit. For proper operation, VIN and VOUT should be constrained to the range: Input Voltage Relative to VSS:.............................. VSS – 0.3V Input Voltage Relative to VDDQ or AVDD: ............. VDD + 0.3V Storage Temperature: ................................–65°C to + 150°C VSS < (VIN or VOUT) < VDD. Operating Temperature: .................................... 0°C to +70°C Unused inputs must always be tied to an appropriate logic voltage level (either VSS or VDD). Maximum ESD .............................................................2000V Maximum Power Supply: ................................................5.5V DC Parameters VDD = VDDPCI = VDDAGP = VDDR = VDD48M = VDDC = 3.3V ± 5%, VDDI = VDD = 2.5V ± 5%, TA = 0°C to +70°C Parameter VIL1 VIH1 VIL2 VIH2 Vol Iol Ioz Idd3.3V Idd2.5V Ipd Ipup Ipdwn Cin Cout Lpin Cxtal Description Input Low Voltage Input High Voltage Input Low Voltage Input High Voltage Output Low Voltage for SRESET# Pull-down Current for SRESET# Three-state Leakage Current Dynamic Supply Current Dynamic Supply Current Power-down Supply Current Internal Pull-up Device Current Internal Pull-down Device Current Input Pin Capacitance Output Pin Capacitance Pin Inductance Crystal Pin Capacitance Conditions Applicable to PD#, F S(0:4) Min. Typ. Max. 0.8 Unit Vdc Vdc Vdc Vdc V mA µA mA mA µA µA µA pF pF pF pF 2.0 Applicable to SDATA and SCLK 1.0 2.2 0.4 24 IOL VOL = 0.4V 35 CPU Frequency Set at 133.3 MHz[5] CPU Frequency Set at 133.3 MHz[5] PD# = 0 Input @ VSS Input @ VDD Measured from the XIN or XOUT to VSS 10 190 195 600 –25 10 5 6 7 45 150 175 95 27 36 AC Parameters Parameter Description XTAL TDC XIN Duty Cycle TPeriod XIN Period VHIGH XIN High Voltage VLOW XIN Low Voltage Tr/Tf XIN Rise and Fall Times TCCJ XIN Cycle to Cycle Jitter Txs Crystal Start-up Time P4 Mode CPU at 0.7V TDC CPUT/C Duty Cycle TPeriod CPUT/C Period Tr/Tf CPUT/C Rise and Fall Times Rise/Fall Matching Delta Tr/Tf Rise/Fall Time Variation TSKEW CPUCS_T/C to CPUT/C Clock Skew TCCJ CPUT/C Cycle to Cycle Jitter 100 MHz Min. Max. 133MHz Min. Max 200 MHz Min. Max Unit Notes[4] 45 69.841 0.7VDD 0 55 71.0 VDD 0.3VDD 10.0 500 30 45 69.84 0.7VDD 0 55 71.0 VDD 0.3VDD 10 500 30 45 69.84 0.7VDD 0 55 71.0 VDD 0.3VDD 10 500 30 % ns V V ns ps ms 7,8 7,8 9 10 10 11,12 12,9 45 55 45 55 45 55 % 9.85 10.2 7.35 7.65 4.85 5.1 ns 175 175 0 700 20% 125 200 ps 0 700 20% 125 150 175 0 700 20% 125 200 ps ps 7,11,14,21, 22 7,11,14,21, 22 23,24 23,26,24 11,23,22 11,15,21,22 –150 +150 –150 +150 –200 +200 ps 11,15,21,22 Notes: 3. Multiple Supplies: The Voltage on any input or I/O pin cannot exceed the power pin during power-up. Power supply sequencing is NOT required. 4. All notes for this table may be found at the end of the table, on page 12. Document #: 38-07367 Rev. *A Page 10 of 21 CY28341 AC Parameters (continued) 100 MHz 133MHz 200 MHz Min. Max. Min. Max Min. Max Parameter Description Vcross Crossing Point Voltage at 0.7V 280 430 280 430 280 430 Swing P4 Mode CPU at 1.0V TDC CPUT/C Duty Cycle 45 55 45 55 45 55 TPeriod CPUT/C Period 9.85 10.2 7.35 7.65 4.85 5.1 Differential CPUT/C Rise and Fall Times 175 467 175 467 175 467 Tr/Tf TSKEW CPUCS_T/C to CPUT/C Clock 0 200 0 150 0 200 Skew TCCJ CPUT/C Cycle to Cycle Jitter –150 +150 –150 +150 –200 +200 Vcross Crossing Point Voltage at 1V 510 760 510 760 510 760 Swing Absolute Single-ended Rise/Fall 325 325 325 SEDeltaSlew Waveform Symmetry K7 Mode TDC CPUOD_T/C Duty Cycle 45 55 45 55 45 55 TPeriod CPUOD_T/C Period 9.98 10.5 7.5 8.0 5 5.5 TLOW CPUOD_T/C LOW Time 2.8 1.67 2.8 Tf CPUOD_T/C Fall Time 0.4 1.6 0.4 1.6 0.4 1.6 TSKEW CPUCS_T/C to CPUT/C Clock 0 200 0 150 0 200 Skew TCCJ CPUOD_T/C Cycle to Cycle Jitter –150 +150 –150 +150 –200 +200 VD Differential Voltage AC 0.4 Vp+.6V 0.4 Vp+.6V 0.4 Vp+.6V VX Differential Crossover Voltage 500 1100 500 1100 500 1100 CHIPSET CLOCK TDC CPUCS_T/C Duty Cycle 45 55 45 55 45 55 TPeriod CPUCS_T/C Period 10.0 10.5 15 15.5 10.0 10.5 Tr / Tf CPUCS_T/C Rise and Fall Times 0.4 1.6 0.4 1.6 0.4 1.6 VD Differential Voltage AC 0.4 Vp+.6V 0.4 Vp+.6V 0.4 Vp+.6V VX Differential Crossover Voltage 0.5*VDDI 0.5*VDDI + 0.5*VDDI 0.5*VDDI 0.5*VDDI 0.5*VDDI – 0.2 – 0.2 – 0.2 0.2 + 0.2 + 0.2 AGP TDC AGP(0:2) Duty Cycle 45 55 45 55 45 55 TPeriod AGP(0:2) Period 15 16 15 16 15 16 THIGH AGP(0:2) HIGH Time 5.25 5.25 5.25 TLOW AGP(0:2) LOW Time 5.05 5.05 5.05 Tr / Tf AGP(0:2) Rise and Fall Times 0.4 1.6 0.4 1.6 0.4 1.6 TSKEW Any AGP to Any AGP clock Skew 250 250 250 TCCJ AGP(0:2) Cycle to Cycle Jitter 500 500 500 PCI TDC PCI(_F,1:6) Duty Cycle 45 55 45 55 45 55 TPeriod PCI(_F,1:6) Period 30.0 30.0 30.0 THIGH PCI(_F,1:6) HIGH Time 12.0 12.0 12.0 TLOW PCI(_F,1:6) LOW Time 12.0 12.0 12.0 Tr / Tf PCI(_F,1:6) Rise and Fall Times 0.5 2.5 0.5 2.5 0.5 2.5 TSKEW Any PCI to Any PCI Clock Skew 500 500 500 TCCJ PCI(_F,1:6) Cycle to Cycle Jitter 500 500 500 48MHz TDC 48MHz Duty Cycle 45 55 45 55 45 55 TPeriod 48MHz Period 20.8299 20.8333 20.8299 20.8333 20.8299 20.8333 Document #: 38-07367 Rev. *A Unit mV Notes[4] 22 % nS ps 11,14,21 11,14,21 13,15,25 0 11,15,21 ps mV 11,15,21 26 ps 24,31 % ns ns ns 0 11,14 11,14 11,14 11,13 11,15,21 ps V mV 11,14 20 19 % ns ns V V 7,11,14 7,11,14 7,11,13 27 21 % ns ns ns ns ps ps 7,11,14 7,11,14 11,16 11,17 11,13 11,15 11,14,15 % ns ns ns ns ps ps 7,11,14 7,11,14 11,16 11,17 11,13 11,15 11,14,15 % ns 7,11,14 7,11,14 Page 11 of 21 CY28341 AC Parameters (continued) Parameter Tr / Tf TCCJ 24MHz TDC TPeriod Tr / Tf TCCJ REF TDC TPeriod Tr / Tf TCCJ DDR VX VD TDC TPeriod Tr / Tf TSKEW TCCJ THPJ TDelay TSKEW tstable Description 48MHz Rise and Fall Times 48MHz Cycle to Cycle Jitter 100 MHz Min. Max. 1.0 4.0 500 133MHz Min. Max 1.0 4.0 500 200 MHz Min. Max 1.0 4.0 500 Unit ns ps Notes[4] 11,13 11,14,15 24MHz Duty Cycle 24MHz Period 24MHz Rise and Fall Times 24MHz Cycle to Cycle Jitter 45 41.660 1.0 55 41.667 4.0 500 45 41.660 1.0 55 41.667 4.0 500 45 41.660 1.0 55 41.667 4.0 500 % ns ns ps 7,11,14 7,11,14 11,13 11,14,15 REF Duty Cycle REF Period REF Rise and Fall Times REF Cycle to Cycle Jitter 45 69.8413 1.0 55 71.0 4.0 1000 45 69.8413 1.0 55 71.0 4.0 1000 45 69.8413 1.0 55 71.0 4.0 1000 % ns ns ps 7,11,14 7,11,14 11,13 11,14,15 0.5*VDD 0.5*VDDD + 0.5*VDDD 0.5*VDDD 0.5*VDDD 0.5*VDDD V – 0.2 + 0.2 –0.2 +0.2 0.2 – 0.2 0.7 VDDD + 0.6 0.7 VDDD + 0.7 VDDD + V 0.6 0.6 DDRT/C(0:5) Duty Cycle 45 55 45 55 45 55 % DDRT/C(0:5) Period 9.85 10.2 14.85 15.3 9.85 10.2 ns DDRT/C(0:5) Rise/Fall Slew Rate 1 3 1 3 1 3 V/ns DDRT/C to Any DDRT/C Clock 100 100 100 ps Skew DDRT/C(0:5) Cycle to Cycle Jitter ±75 ±75 ±75 ps DDRT/C(0:5) Half-period Jitter ±100 ±100 ±100 ps BUF_IN to Any DDRT/C Delay 1 4 1 4 1 4 ns FBOUT to Any DDRT/CSkew 100 100 100 ps All Clock Stabilization from 3 3 3 ms Power-up Crossing Point Voltage of DDRT/C Differential Voltage Swing 19 20 21 21 13 11,15,21 11,15,21 11,15,21 11,14 11,14 18 Notes: 5. All outputs loaded as per maximum capacitive load table. 6. All outputs are not loaded. 7. This parameter is measured as an average over a 1-µs duration, with a crystal center frequency of 14.31818 MHz. 8. This is required for the duty cycle on the REF clock out to be as specified. The device will operate reliably with input duty cycles up to 30/70 but the REF clock duty cycle will not be within data sheet specifications. 9. When crystal meets minimum 40-ohm device series resistance specification. 10. Measured between 0.2VDD and 0.7VDD. 11. All outputs loaded as per loading specified in the Table 11. 12. When XIN is driven from an external clock source (3.3V parameters apply). 13. Probes are placed on the pins, and measurements are acquired between 0.4V and 2.4V for 3.3V signals and between 0.4V and 2.0V for 2.5V signals, and between 20% and 80% for differential signals. 14. Probes are placed on the pins, and measurements are acquired at 1.5V for 3.3V signals and at 1.25V for 2.5V, and 50% point for differential signals. 15. This measurement is applicable with Spread ON or spread OFF. 16. Probes are placed on the pins, and measurements are acquired at 2.4V for 3.3V signals and at 2.0V for 2.5V signals) 17. Probes are placed on the pins, and measurements are acquired at 0.4V. 18. The time specified is measured from when all VDD’s reach their respective supply rail (3.3V and 2.5V) till the frequency output is stable and operating within the specifications. 19. The typical value of VX is expected to be 0.5*VDDD (or 0.5*VDDC for CPUCS signals) and will track the variations in the DC level of the same. 20. VD is the magnitude of the difference between the measured voltage level on a DDRT (and CPUCS_T) clock and the measured voltage level on its complementary DDRC (and CPUCS_C) one. 21. Measured at VX, or where subtraction of CLK-CLK# crosses 0 volts. 22. See Figure 10. for 0.7V loading specification. 23. Measured from Vol=0.175V to Voh=0.525V. 24. Measurements taken from common mode waveforms, measure rise/fall time from 0.41V to 0.86V. Rise/fall time matching is defined as “the instantaneous difference between maximum clk rise (fall) and minimum clk# fall (rise) time, or minimum clk rise (fall) and maximum clk# fall (rise) time”. This parameter is designed for waveform symmetry. 25. Measurement taken from differential waveform, from -0.35V to +0.35V. 26. Measured in absolute voltage, i.e. single-ended measurement. 27. Measured at VX between the rising edge and the following falling edge of the signal. 28. Measured at VX between the falling edge and the following rising edge of the signal. 29. This parameter is intended to be 0.45*Tperiod(min) for minimum spec. and 0.55*Tperiod(min) for maximum spec. 30. Determined as a fraction of 2*(Trise-Tfall)/(Trise+Tfall). Document #: 38-07367 Rev. *A Page 12 of 21 CY28341 P4 Processor SELP4_K7# = 1 Power-down Assertion (P4 Mode) When PD# is sampled LOW by two consecutive rising edges of CPU# clock then all clock outputs except CPU clocks must be held LOW on their next HIGH to LOW transition. CPU clocks must be held with the CPU clock pin driven HIGH with a value of 2 x Iref, and CPU# undriven. Note that Figure 4 shows CPU = 133 MHz, this diagram and description is applicable for all valid CPU frequencies 66, 100, 133, 200MHz.Due to the state of internal logic, stopping and holding the REF clock outputs in the LOW state may require more than one clock cycle to complete. PW RDW N# CPUT 133M Hz CPUT# 133M Hz PCI 33M Hz AG P 66M Hz USB 48M Hz R E F 1 4 .3 1 8 M H z D DRT 133M Hz DDR C 133M Hz SD RAM 133M Hz Figure 2. Power-down Assertion Timing Waveform (in P4 Mode) Document #: 38-07367 Rev. *A Page 13 of 21 CY28341 Rise and Fall Times Power-down Deassertion (P4 Mode) The power-up latency needs to be less than 3 mS. < 1 .5 m s e c PW RDW N# CPU 133MHz C PU# 133MHz PCI 33MHz AGP 66MHz USB 48MHz R E F 1 4 .3 1 8 M H z D DRT 133MHz DD RC 133MHz SDR AM 133MHz Figure 3. Power-down Deassertion Timing Waveform (in P4 Mode) AMD K7 Processor SELP4_K7# = 0 Power-down Assertion (K7 Mode) When the PD# signal is asserted LOW, all clocks are disabled to a LOW level in an orderly fashion prior to removing power from the part. When PD# is asserted (forced) LOW, the device transitions to a shutdown (power-down) mode and all power supplies may then be removed. When PD# is sampled LOW Document #: 38-07367 Rev. *A by two consecutive rising edges of CPU clock, then all affected clocks are stopped in a LOW state as soon as possible. When in power-down (and before power is removed), all outputs are synchronously stopped in a LOW state (see figure3 below), all PLL’s are shut off, and the crystal oscillator is disabled. When the device is shutdown, the I2C function is also disabled. Page 14 of 21 CY28341 PW RDW N# C P U O D _T 133M H z C P U C S _T 133M H z C P U O D _C 133M H z C P U C S _C 133M H z P C I 33M H z A G P 66M H z U S B 48M H z R E F 14.318M H z D D R T 133M H z D D R C 133M H z S D R A M 133M H z Figure 4. Power-down Assertion Timing Waveform (in K7 Mode) Document #: 38-07367 Rev. *A Page 15 of 21 CY28341 Power-down Deassertion (K7 Mode) When de-asserted PD# to HIGH level, all clocks are enabled and start running on the rising edge of the next full period in order to guarantee a glitch-free operation, no partial clock pulses. < 1 .5 m se c PW RDW N# CPU 133MHz CPU# 133MHz PCI 33MHz AGP 66MHz USB 48MHz R E F 1 4 .3 1 8 M H z DDRT 133MHz DDRC 133MHz SDRAM 133MHz Figure 5. Power-down Deassertion Timing Waveform (in K7 mode) VID (0:3), SEL (0,1) VTT_PW RGD# PW RGD 0.2-0.3m S Delay VDD Clock Gen Clock State Clock Outputs Clock VCO State 0 W ait for VTT_GD# State 1 State 2 Off Off Sam ple Sels State 3 On (Note A) On Figure 6. VTT_PWGD# Timing Diagram (With Advanced PIII Processor SelP4_K7 = 1)[31] Note: 31. This time diagram shows that VTT_PWRGD# transits to a logic LOW in the first time at power-up. After the first HIGH to LOW transition of VTT_PWRGD#, device is not affected, VTT_PWRGD# is ignored. Document #: 38-07367 Rev. *A Page 16 of 21 WR TP =L VT S1 ow GD # CY28341 S2 W a it fo r 1 .1 4 6 m s S a m p le In p u ts F S ( 3 :0 ) D e la y 0 .2 5 m S E n a b le O u tp u te s V D D A = 2 .0 V S0 S3 P o w e r O ff N o rm a l O p e r a tio n V D D 3 .3 = O f f Figure 7. Clock Generator Power-up/ Run State Diagram (with P4 Processor SELP4_K7# = 1) Connection Circuit DDRT/C Signals For Open Drain CPU Output Signals (with K7 Processor SELP4_K7# = 0) VDDCPU(1.5V) 3.3V 60.4 Ohm CPUOD_T 47 Ohm 52 Ohm 5" 500 Ohm Measurement Point 52 Ohm 1" 680 pF 20 pF 500 Ohm 301 Ohm 47 Ohm CPUOD_C VDDCPU(1.5V) 52 Ohm 1" 500 Ohm 52 Ohm 5" 680 pF 60.4 Ohm 500 Ohm Measurement Point 20 pF 3.3V Figure 8. 6” 6” Figure 9. Document #: 38-07367 Rev. *A Page 17 of 21 CY28341 Table 10. Signal Loading Table Clock Name Max Load (in pF) REF (0:1), 48MHz (USB), 24_48MHz 20 AGP(0:2), SDRAM (0:11) 30 PCI_F(0:5) 30 DDRT/C (0:5), FBOUT CPUT/C See Figure 10 CPUOD_T/C See Figure 8 CPUCS_T/C See Figure 9 For Differential CPU Output Signals (with P4 Processor SELP4_K7= 1) The following diagram shows lumped test load configurations for the differential Host Clock Outputs. CLK Measurement Point T PCB CPUT RtA1 RtB1 R LB1 RLA1 C LA RD MULTSEL CLK Measurement Point T PCB CPUT# RtA2 RLA2 R LB2 RtB2 C LB R ref Figure 10. Group Timing Relationships and Tolerances[32] Table 11. Lumped Test Load Configuration Component 0.7V Amplitude Value 1.0V Amplitude Value RtA1, RtA2 33Ω 0Ω RLA1, RLA2 49.9Ω ∞ TPCB 3” 50 ΩZ 3” 50 ΩZ RLB1, RLB2 ∞ 63Ω RD ∞ 470Ω RtB1, RtB2 0Ω 33Ω CLA, CLB 2 pF 2 pF Rref 475Ω w/mult0 = 1 221Ω w/mult0 = 0 Offset (ps) Tolerance (ps) Conditions tCSAGP CPUCS to AGP tAP AGP to PCI 750 500 CPUCS Leads 1,250 500 AGP Leads Note: 32. Ideally the probes should be placed on the pins. If there is a transmission line between the test point and the pin for one signal of the pair (e.g., CPU), the same length transmission line to the other signal of the pair (e.g., AGP) should be added. Document #: 38-07367 Rev. *A Page 18 of 21 CY28341 0ns 10ns 20ns 30ns CPU CLOCK 66.6MHz CPU CLOCK 100MHz CPU CLOCK 133.3MHz tCSAGP AGP CLOCK 66.6MHz tAP PCI CLOCK 33.3MHz Ordering Information Part Number CY28341OC CY28341OCT CY28341ZC CY28341ZCT Package Type 56-pin Shrunk Small Outline package (SSOP) 56-pin Shrunk Small Outline package (SSOP)–Tape and Reel 56-pin Thin Shrunk Small Outline package (TSSOP) 56-pin Thin Shrunk Small Outline package (TSSOP)–Tape and Reel Document #: 38-07367 Rev. *A Product Flow Commercial, 0° to 70°C Commercial, 0° to 70°C Commercial, 0° to 70°C Commercial, 0° to 70°C Page 19 of 21 CY28341 Package Drawing and Dimensions 56-lead Thin Shrunk Small Outline Package, Type II (6 mm × 12 mm) Z56 51-85060-B 56-lead Shrunk Small Outline Package O56 51-85062-C Purchase of I2C components from Cypress or one of its sublicensed Associated Companies conveys a license under the Philips I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips. VIA is a trademark of VIA Technologies, Inc. Pentium 4 is a registered trademark of Intel Corporation. Athlon is a trademark of AMD Corporation, Inc. Dial-a-Frequency, Dial-a-dB, Dial-a-Skew, and Dial-a-Ratio are trademarks of Cypress Semiconductor. All product and computer names mentioned in this document may be the trademarks of their respective holders. Document #: 38-07367 Rev. *A Page 20 of 21 © Cypress Semiconductor Corporation, 2002. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges. CY28341 Document Title: CY28341 Universal Single-Chip Clock Solution for VIA P4M266/KM266 DDR Systems Document Number: 38-07367 REV. ECN NO. Issue Date Orig. of Change ** 112783 05/28/02 DMG *A 122908 12/26/02 RBI Document #: 38-07367 Rev. *A Description of Change New Data Sheet Add power requirements to maximum ratings information Page 21 of 21