SINGLE-PHASE BRIDGE RECTIFIER DF005 THRU DF10 DB101 THRU DB107 CURRENT FEATURES • • • • 50 to 1000 Volts VOLTAGE RANGE 1.0 Ampere DFM Glass passivated chip junction High forward surge current capability Ideal for printed circuit board High temperature soldering guaranteed: 260℃/10 seconds at terminals .365 (9.3) .320 ( 8.12) .135 (3.4) .115 (2.9) .165 (4.2) .020 .155 ( 3.9) ( 0.5) .350 (8.9) .300 ( 7.6) .060 ( 1.5) MECHANICAL DATA • • • • • • .205 (5.2) .195 ( 5.0) Case: Transfer molded plastic Epoxy: UL94V-0 rate flame retardant Terminals solderable per MIL-STD-202E method 208C Polarity: Molded on body Mounting position: Any Weight: 0.04 ounce, 1.0 gram - + ~ ~ .255 (6.5) .245 ( 6.2) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25℃ ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% Maximum Reverse Peak Repetitive Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Output Current, 0.06”(1.5mm) lead length at T A=40℃ (Note 2) Peak Forward Surge Current 8.3ms single half sine wave superimposed on rated load (JEDEC Method) Rating for Fusing (t＜8.3ms) Maximum Instantaneous Forward Voltage drop Per Bridge element 1.0A Maximum Reverse Current at rated DC blocking voltage per element TA=25℃ TA=125℃ Typical Junction Capacitance (Note 1) Typical Thermal Resistance (Note 2) Operating and Storage Temperature Range SYMBOLS DF005 DB101 DF01 DB102 DF02 DB103 DF04 DB104 DF06 DB105 DF08 DB106 DF10 DB107 UNIT VRRM VRMS VDC 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 Volts Volts Volts I(AV) 1.0 Amps IFSM 50 Amps I2 t 10 A2s VF 1.1 Volts 5 0.5 25 40 -55 to +150 IR CJ RΘJA TJ ,TSTG Notes: 1. Measured at 1.0MHz and applied reverse voltage of 4.0 Volts. 2.Unit mounted on P.C.B. with 0.51”×0.51” ( 13×13mm) copper pads. E-mail: [email protected] Web Site: www.cnmic.com µAmps mAmps pF ℃/W ℃ SINGLE-PHASE BRIDGE RECTIFIER DF005 THRU DF10 DB101 THRU DB107 CURRENT RATINGS AND CHARACTERISTIC CURVES FIG. 2- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER ELEMENT 70 1.0 PEAK FORWARD SURGE, CURRENT,(A) AVERAGE FORWARD OUTPUT, CURRENT,(A) 1.2 0.8 0.6 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.4 0.2 0 0 25 75 40 50 100 150 125 175 60 Tj =Tj max Single Half Sine-Wave ( JEDEC Method) 50 40 30 20 10 0 1 CYCLE 1 2 4 AMBIENT TEMPERATURE, ℃ 6 8 10 40 20 60 80 100 NUMBER OF CYCLES AT 60 Hz FIG. 3- TYPICAL FORWORD CHARACTERISTICS PER BRIDGE ELEMENT FIG. 4- TYPICAL REVERSE CHARACTERISTICS PER BRIDGE ELEMENT 20 100 10 INSTANTANEOUS REVERSE CURRENT, (μA) INSTANTANEOUS FORWARD CURRENT, (A) 1.0 Ampere DF10 DF005 THRU DB101 DB107 FIG. 1- DERATING CURVE FOR OUTPUT RECTIFIED CURRENT 1.0 0.1 0.01 Tj =25℃ PULSE WIDTH=300μs 1% DUTY CYCLE 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, (V) 100 JUNCTION CAPACITANCE, (pF) 50 to 1000 Volts VOLTAGE RANGE 10 Tj =125℃ 1.0 0.1 Tj =25℃ FIG. 5- TYPICAL JUNCTION CAPACITANCE PER BRIDGE ELEMENT 0.01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) 10 T j =25℃ f=1MHz Vsig=50mVp-p 1 0.1 1.0 10 100 REVRESE VOLTAGE,(V) E-mail: [email protected] Web Site: www.cnmic.com 120 140