ASW220 CATV MMIC Amplifier Description The ASW220, a wideband Description Features Features 16.8 dB Gain at 500 MHz linear amplifier MMIC, has a high linearity and low noise over a wide range of frequency 5 MHz to 3 GHz, being suitable for use in the fiber receiver, distribution amplifiers and drop amplifiers of CATV systems, and in the mobile wireless repeaters and BTS. The amplifier is available in a SOT89 package and passes through the stringent DC, RF, and reliability tests. 18.5 dBm P1dB at 500 MHz 37 dBm Output IP3 at 500 MHz 3.4 dB NF at 500 MHz 75 Input & Output Match Bandwidth 5 ~ 1200 MHz Single Supply +5 V ASW220 Package Style: SOT89 Typical Performance Application Circuit (Supply Voltage = +5 V, TA = +25 C, Z0 = 75 ) Parameters Units Typical Frequency MHz 5 50 500 860 1200 2100 Noise Figure dB 3.3 3.3 3.4 3.4 3.4 4.2 CATV & 50 ~ 1200 MHz Gain dB 16.9 17.0 16.8 16.7 16.0 15.7 CATV & 5 ~ 200 MHz S11 dB -20 -20 -20 -16 -17 -12 S22 dB -20 -20 -18 -18 -16 -10 Output P1dB dBm 17.5 18.0 18.5 17.0 17.0 16.5 SMATV & 200 ~ 3000 MHz Output IP31) dBm 36.0 36.5 37.0 32.0 31.5 29.5 5000 ~ 6000 MHz Output IP21),2) dBm 47 48 48 42 45 35 CSO3) dBc 60 CTB3) dBc 75 Current mA 75 90 Device Voltage V +5 +5 CATV & 50 ~ 1000 MHz SMATV & 900 ~ 2100 MHz 1) OIP3 and OIP2 are measured with two tones at an output power of +5 dBm/tone separated by 1 MHz (up-link) or 6 MHz (down-link). 2) OIP2 is measured at F1+F2 Frequency. 3) 60 channels, +28 dBmV per channel (measured at output). Product Specifications Parameters Units Min Typ. Testing Frequency MHz 500 Gain dB 16.8 S11 dB -20 S22 dB -18 Output IP3 dBm 37 Noise Figure dB 3.4 Output P1dB dBm 18.5 Current mA 75 Device Voltage V +5 Max Pin Configuration Absolute Maximum Ratings Parameters Rating Operating Case Temperature -40 to 85 C Storage Temperature -40 to 150 C Device Voltage +6 V Operating Junction Temperature Pin No. Function 1 RF IN +150 C 2 GND Input RF Power (Continuous)* +25 dBm 3 RF OUT & Bias Thermal Resistance 158 C/W * Please find the max. input power data from http://www.asb.co.kr/pdf/Maximum_Input_Power_Analysis.pdf 1/12 ASB Inc. [email protected] Tel: +82-42-528-7223 June 2017 ASW220 CATV MMIC Amplifier Outline Drawing Part No. Lot No. ASW220 Pxxxx Symbols A L b b1 C D D1 E E1 e1 H S e Dimensions (In mm) MIN NOM 1.40 1.50 0.89 1.04 0.36 0.42 0.41 0.47 0.38 0.40 4.40 4.50 1.40 1.60 3.64 --2.40 2.50 2.90 3.00 0.35 0.40 0.65 0.75 1.40 1.50 Pin No. Function 1 RF IN 2 GND 3 RF OUT & Bias MAX 1.60 1.20 0.48 0.53 0.43 4.60 1.75 4.25 2.60 3.10 0.45 0.85 1.60 Mounting Recommendation (In mm) Note: 1. The number and size of ground via holes in a circuit board is critical for thermal and RF grounding considerations. 2. We recommend that the ground via holes be placed on the bottom of the lead pin 2 and exposed pad of the device for better RF and thermal performance, as shown in the drawing at the left side. ESD Classification HBM Class 1A Voltage Level: 400 V MM Class A Voltage Level: 50 V CAUTION: ESD-sensitive device! ` Moisture Sensitivity Level (MSL) Level 3 at 260 C reflow 2/12 ASB Inc. [email protected] Tel: +82-42-528-7223 June 2017 ASW220 CATV MMIC Amplifier APPLICATION CIRCUIT CATV Frequency (MHz) 50 500 860 Noise Figure (dB) 3.6 3.7 3.6 Magnitude S21 (dB) 16.7 16.5 16.0 Magnitude S11 (dB) -17 -17 -16 Magnitude S22 (dB) -17 -14 -11 Output P1dB (dBm) 18.0 17.5 16.5 Output IP31) (dBm) 37.0 35.5 32.0 48 50 45 50 ~ 1000 MHz Output IP2 +5 V CSO3) (dBc) 60 CTB3) (dBc) 75 Device Voltage (V) +5 Current (mA) 75 1),2) (dBm) . 1) OIP3 and OIP2 are measured with two tones at an output power of +5 dBm/tone separated by 6 MHz. 2) OIP2 is measured at F1+F2 Frequency. 3) 60 channels, +28 dBmV per channel (measured at output). Board Layout (FR4, 40x40 mm2, 0.8T) Schematic S-parameters 0 25 -5 -10 15 S11 (dB) Gain (dB) 20 10 -15 -20 5 0 -25 -30 0 200 400 600 800 1000 0 200 400 600 800 1000 Frequency (MHz) Frequency (MHz) 0 -5 S22 (dB) -10 -15 -20 -25 -30 0 200 400 600 800 1000 Frequency (MHz) 3/12 ASB Inc. [email protected] Tel: +82-42-528-7223 June 2017 ASW220 CATV MMIC Amplifier APPLICATION CIRCUIT CATV Frequency (MHz) 50 500 1200 Noise Figure (dB) 3.7 3.9 3.4 Magnitude S21 (dB) 16.7 16.5 16.0 Magnitude S11 (dB) -17 -17 -17 Magnitude S22 (dB) -17 -16 -16 Output P1dB (dBm) 18.0 17.5 17.0 Output IP31) (dBm) 37.0 35.5 31.5 48 50 45 50 ~ 1200 MHz Output IP2 +5 V CSO3) (dBc) - CTB3) (dBc) - Device Voltage (V) +5 Current (mA) 75 1),2) (dBm) . 1) OIP3 and OIP2 are measured with two tones at an output power of +5 dBm/tone separated by 6 MHz. 2) OIP2 is measured at F1+F2 Frequency. Board Layout (FR4, 40x40 mm2, 0.8T) Schematic S-parameters 0 25 -5 -10 15 S11 (dB) Gain (dB) 20 10 -15 -20 5 0 -25 -30 0 200 400 600 800 1000 1200 1400 0 200 Frequency (MHz) 400 600 800 1000 1200 1400 Frequency (MHz) 0 -5 S22 (dB) -10 -15 -20 -25 -30 0 200 400 600 800 1000 1200 1400 Frequency (MHz) 4/12 ASB Inc. [email protected] Tel: +82-42-528-7223 June 2017 ASW220 CATV MMIC Amplifier APPLICATION CIRCUIT CATV Frequency (MHz) 50 500 860 Noise Figure (dB) 3.3 3.5 3.5 Magnitude S21 (dB) 16.5 16.6 16.0 Magnitude S11 (dB) -12 -17 -11 Magnitude S22 (dB) -10 -14 -10 Output P1dB (dBm) 18.0 18.5 17.5 Output IP31) (dBm) 35 37 33 45 50 50 50 ~ 1000 MHz Output IP2 +5 V CSO3) (dBc) 60 CTB3) (dBc) 75 Device Voltage (V) +5 Current (mA) 75 1),2) (dBm) . 1) OIP3 and OIP2 are measured with two tones at an output power of +5 dBm/tone separated by 6 MHz. 2) OIP2 is measured at F1+F2 Frequency. 3) 60 channels, +28 dBmV per channel (measured at output). Board Layout (FR4, 40x40 mm2, 0.8T) Schematic Vs=5 V C3=1 F L1=390 nH (Coil Inductor) RF IN C1=1 nF C2=1 nF RF OUT ASW220 25 0 20 -5 15 -10 S11 (dB) Gain (dB) S-parameters 10 5 -15 -20 0 -25 0 100 200 300 400 500 600 700 800 900 1000 0 100 Frequency (MHz) 200 300 400 500 600 700 800 900 1000 Frequency (MHz) 0 -5 S22 (dB) -10 -15 -20 -25 0 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) 5/12 ASB Inc. [email protected] Tel: +82-42-528-7223 June 2017 ASW220 CATV MMIC Amplifier APPLICATION CIRCUIT CATV 5 ~ 200 MHz Frequency (MHz) 5 50 200 Noise Figure (dB) 3.3 3.3 3.3 Magnitude S21 (dB) 16.9 17.0 16.9 Magnitude S11 (dB) -20 -20 -20 Magnitude S22 (dB) -20 -20 -15 Output P1dB (dBm) 17.5 17.5 17.5 Output IP3 (dBm) 36 36 36 Output IP21),2) (dBm) 47 47 49 Device Voltage (V) +5 Current (mA) 75 1) +5 V . 1) OIP3 and OIP2 are measured with two tones at an output power of +5 dBm/tone separated by 1 MHz. 2) OIP2 is measured at F1+F2 Frequency. Board Layout (FR4, 40x40 mm2, 0.8T) Schematic S-parameters 0 25 20 15 S11 (dB) Gain (dB) -10 10 -20 -30 5 0 -40 0 50 100 150 200 250 300 0 50 100 150 200 250 300 Frequency (MHz) Frequency (MHz) 0 S22 (dB) -10 -20 -30 -40 0 50 100 150 200 250 Frequency (MHz) 6/12 ASB Inc. [email protected] Tel: +82-42-528-7223 June 2017 ASW220 CATV MMIC Amplifier APPLICATION CIRCUIT CATV 5 ~ 200 MHz Frequency (MHz) 5 50 200 Noise Figure (dB) 4.3 4.5 4.6 Magnitude S21 (dB) 10.2 10.3 10.3 Magnitude S11 (dB) -7 -7 -7 Magnitude S22 (dB) -7 -7 -7 Output P1dB (dBm) 16.5 16.5 17.0 Output IP3 (dBm) 34 34 35 Output IP21),2) (dBm) 46 47 50 Device Voltage (V) +5 Current (mA) 75 1) +5 V . 1) OIP3 and OIP2 are measured with two tones at an output power of +5 dBm/tone separated by 1 MHz. 2) OIP2 is measured at F1+F2 Frequency. Board Layout (FR4, 40x40 mm2, 0.8T) Schematic 20 0 15 -5 S11 (dB) Gain (dB) S-parameters 10 5 0 -10 -15 0 50 100 150 200 250 300 -20 0 50 Frequency (MHz) 100 150 200 250 300 Frequency (MHz) 0 S22 (dB) -5 -10 -15 -20 0 50 100 150 200 250 Frequency (MHz) 7/12 ASB Inc. [email protected] Tel: +82-42-528-7223 June 2017 ASW220 CATV MMIC Amplifier APPLICATION CIRCUIT CATV 5 ~ 200 MHz Frequency (MHz) 5 50 200 Noise Figure (dB) 3.3 3.2 3.7 Magnitude S21 (dB) 16.5 16.5 16.5 Magnitude S11 (dB) -20 -20 -20 Magnitude S22 (dB) -18 -20 -15 Output P1dB (dBm) 12.0 12.0 12.0 Output IP3 (dBm) 30.0 30.0 30.5 Output IP21),2) (dBm) 39.5 40.0 41.0 Device Voltage (V) +3.3 Current (mA) 48 1) +3.3 V . 1) OIP3 and OIP2 are measured with two tones at an output power of +0 dBm/tone separated by 1 MHz. 2) OIP2 is measured at F1+F2 Frequency. Board Layout (FR4, 40x40 mm2, 0.8T) Schematic S-parameters 25 0 20 15 S11 (dB) Gain (dB) -10 10 -20 -30 5 0 -40 0 50 100 150 200 250 300 0 50 100 150 200 250 300 Frequency (MHz) Frequency (MHz) 0 S22 (dB) -10 -20 -30 -40 0 50 100 150 200 250 Frequency (MHz) 8/12 ASB Inc. [email protected] Tel: +82-42-528-7223 June 2017 ASW220 CATV MMIC Amplifier APPLICATION CIRCUIT SMATV 900 ~ 2100 MHz Frequency (MHz) 900 1500 2100 Noise Figure (dB) 3.9 4.0 4.2 Magnitude S21 (dB) 16.5 16.0 15.7 Magnitude S11 (dB) -10 -13 -12 Magnitude S22 (dB) -17 -12 -10 Output P1dB (dBm) 16.5 19.0 16.5 Output IP3 (dBm) 32.0 34.0 29.5 Output IP21),2) (dBm) 40 42 35 Device Voltage (V) +5 Current (mA) 75 1) +5 V . 1) OIP3 and OIP2 are measured with two tones at an output power of +5 dBm/tone separated by 6 MHz. 2) OIP2 is measured at F1+F2 Frequency. Board Layout (FR4, 40x40 mm2, 0.8T) Schematic Vs=5 V C4=1 F L1=15 nH RF IN C1=1 nF RF OUT C2=1 nF ASW220 C3=0.3 pF 20 0 15 -5 S11 (dB) Gain (dB) S-parameters 10 5 0 -10 -15 0 500 1000 1500 2000 2500 3000 -20 0 500 Frequency (MHz) 1000 1500 2000 2500 3000 Frequency (MHz) 0 -5 S22 (dB) -10 -15 -20 -25 -30 0 500 1000 1500 2000 2500 3000 Frequency (MHz) 9/12 ASB Inc. [email protected] Tel: +82-42-528-7223 June 2017 ASW220 CATV MMIC Amplifier APPLICATION CIRCUIT SMATV 200 ~ 3000 MHz Frequency (MHz) 200 1000 2000 2600 3000 Noise Figure (dB) 3.8 3.5 4.2 4.2 4.2 Magnitude S21 (dB) 16.5 15.5 14.5 14.0 13.0 Magnitude S11 (dB) -16 -14 -13 -9 -8 Magnitude S22 (dB) -18 -12 -9 -8 -8 Output P1dB (dBm) 18 18 16 17 16 Output IP3 (dBm) 39.5 33.5 29.5 30.5 28.0 Output IP21),2) (dBm) 50 44 37 45 34 1) +5 V Device Voltage (V) +5 Current (mA) 75 . 1) OIP3 and OIP2 are measured with two tones at an output power of +5 dBm/tone separated by 6 MHz. 2) OIP2 is measured at F1+F2 Frequency. Board Layout (FR4, 40x40 mm2, 0.8T) Schematic 25 0 20 -5 15 -10 S11 (dB) Gain (dB) S-parameters 10 -20 5 0 -15 -25 0 800 1600 2400 3200 0 800 1600 2400 3200 Frequency (MHz) Frequency (MHz) 0 S22 (dB) -10 -20 -30 -40 0 800 1600 2400 3200 Frequency (MHz) 10/12 ASB Inc. [email protected] Tel: +82-42-528-7223 June 2017 ASW220 CATV MMIC Amplifier APPLICATION CIRCUIT Frequency (MHz) 5000 6000 Noise Figure (dB) 4.10 4.86 Magnitude S21 (dB) 14.2 14.1 Magnitude S11 (dB) -8.8 -7.6 Magnitude S22 (dB) -5.2 -3.3 Output P1dB (dBm) 13.0 12.3 21.3 5000 ~ 6000 MHz Output IP3 (dBm) 24.2 +5 V Device Voltage (V) +5 Current (mA) 75 1) . 1) OIP3 and are measured with two tones at an output power of +5 dBm/tone separated by 1 MHz. Board Layout (FR4, 40x40 mm2, 0.8T) Schematic Vs = 5 V C2 = 1 uF C3 = 100 pF L1 = 5.6 nH RF IN C1 = 10 pF C4 = 10 pF RF OUT ASW220 S-parameters 0 25 20 15 S11 (dB) Gain (dB) -5 10 -10 -15 5 0 4500 5000 5500 Frequency (MHz) 6000 5000 5500 Frequency (MHz) 6000 6500 -20 4500 5000 5500 Frequency (MHz) 6000 6500 0 S22 (dB) -5 -10 -15 -20 4500 11/12 6500 ASB Inc. [email protected] Tel: +82-42-528-7223 June 2017 ASW220 CATV MMIC Amplifier Recommended Soldering Reflow Profile 260 C Ramp-up (3 C/sec) 20~40 sec Ramp-down (6 C/sec) 200 C 150 C 60~180 sec Copyright 2010-2017 ASB Inc. All rights reserved. Datasheet subject to change without notice. ASB assumes no responsibility for any errors which may appear in this datasheet. No part of the datasheet may be copied or reproduced in any form or by any means without the prior written consent of ASB. 12/12 ASB Inc. [email protected] Tel: +82-42-528-7223 June 2017