ACDC 125 Watts CLC Series xppower.com • 125 W Forcedcooled Rating • Low Profile 1.25” • Industry Standard 2” x 4” & 3” x 5” Package Sizes • 12 V Fan Supply • Optional ORing Diode • <0.5 W No Load Input Power • 3 Year Warranty Specification Input General • 85-264 VAC (120-370 VDC), Derate output power linearly to 90% from 90 VAC to 85 VAC Input Frequency • 47-63 Hz Input Current • 2.3 A typical at 115 VAC, full load 1.1 A typical at 230 VAC, full load Inrush Current • 40 A max at 230 VAC, cold start 25 °C Power Factor • EN61000-3-2, class A No Load Input Power • <0.5 W Earth Leakage Current • 80/160 µA typical 115/230 VAC 50 Hz 300 µA at 264 VAC/60 Hz max. Input Protection • Internal T5 A/250 V fuse in line Input Voltage Output Output Voltage Output Voltage Trim Initial Set Accuracy Minimum Load Start Up Delay Start Up Rise Time Hold Up Time Drift Line Regulation Load Regulation Over/Undershoot Transient Response • • • • • • • • • • • • Ripple & Noise Overvoltage Protection Overload Protection Short Circuit Protection Temperature Coefficient • • • • • 12-48 VDC (see tables) ±10% ±1% No minimum load required 1 s typical 50 ms 16 ms min at 230 VAC ±0.2% after 20 min warm up ±0.5% max ±1% 5% typical 4% max. deviation, recovery to within 1% in 500 µs for a 50-75-50% load change 1% pk-pk V1, 20 MHz bandwidth 115-140% Vnom, recycle input to reset 110-150% Continuous trip and restart (hiccup mode) 0.05%/˚C Efficiency Isolation Switching Frequency MTBF • 88% typical • 3000 VAC Input to Output, 1500 VAC Input to Ground, 500 VDC Output to Ground • 65 KHz typical • 1,245 KHrs to Telecordia SR-332 at 25 °C, GB Environmental Operating Temperature • 0 ˚C to +70 ˚C derate linearly from +50 ˚C at 2.5%/˚C to 50% load at +70 ˚C. Cooling • Forced cooled, 10 CFM Operating Humidity • 95% RH, non-condensing Storage Temperature • -40 ˚C to +85 ˚C Operating Altitude • 3000 m Shock • 30 g pk, half sine, 6 axes Vibration • 2 g rms, 5 Hz to 500 kHz, 3 axes EMC & Safety Low Voltage PSU EMC • EN61204-3, high severity level as below Emissions • EN55022 level B conducted EN55022 level A radiated Harmonic Currents • EN61000-3-2, class A Voltage Flicker • EN61000-3-3 Radiated Immunity • EN61000-4-3, level 3 Perf Criteria A EFT/Burst • EN61000-4-4, level 3 Perf Criteria A Surge • EN61000-4-5, installation class 3 Perf Criteria A Conducted Immunity • EN61000-4-6, level 3 Perf Criteria A Dips & Interruptions • EN61000-4-11, 30% 10 ms, 60% 100 ms, 100% 5000 ms, Perf Criteria A, B, B Safety Approvals • IEC60950-1 CB report, CSA 22.2 No. 60950-1, UL60950-1, TUV EN60950-1 Equipment Protection • Class I Class Output Power Output Voltage V1 Output Current Fan Supply V2 55 W 12.0 VDC 10.4 A 12 V / 0.5 A CLC125US12 55 W 24.0 VDC 5.2 A 12 V / 0.5 A CLC125US24 125 W 55 W 48.0 VDC 2.6 A 12 V / 0.5 A CLC125US48 125 W 55 W 12.0 VDC 10.4 A 12 V / 0.5 A CLC125US12-3x5(1) 125 W 55 W 24.0 VDC 5.2 A 12 V / 0.5 A CLC125US24-3x5(1) 125 W 55 W 48.0 VDC 2.6 A 12 V / 0.5 A CLC125US48-3x5(1) 125 W 55 W 12.0 VDC 10.4 A 12 V / 0.5 A CLC125US12D-3x5(1) 125 W 55 W 24.0 VDC 5.2 A 12 V / 0.5 A CLC125US24D-3x5(1) 125 W 55 W 48.0 VDC 2.6 A 12 V / 0.5 A CLC125US48D-3x5(1) 10 CFM Convection 125 W 125 W Model Number Notes 1. The 3 x 5 models share the same specification as the other models except the PCB size is increased to 3” x 5” from 2” x 4”. The ‘D’ models have an integral output ORing diode. Mechanical Details CLC125 4.00 (101.6) 1.25 (31.8) J1 mates with Molex housing p/n 09-50-1031, and Molex series 5194 crimp terminals 3.750 (95.25) 0.125 (3.18) Voltage Adj. Output Connector J2 Molex PN 09-65-2048 Pin 1 +V1 Pin 2 +V1 Pin 3 RTN Pin 2 RTN 1.750 (44.45) 2.00 (50.8) J1 J2 1.29 (32.7) 1.00 (25.4) J2 mates with Molex housing p/n 09-50-1041 and Molex series 5194 crimp terminals Fan Supply Connector J3 Molex PN 22-04-1021 Pin 1 Fan+ Pin 2 Fan- 0.45 J3 (11.4) 0.125 (3.18) 0.20 (5.1) 0.29 (7.3) 0.20 (5.1) 0.25 Faston Ground Tab 0.14 (3.5) SMD Component Height 4 X ø.156 (3.96) Mounting Holes ø.312 (7.92) Clearance top and bottom CLC125 3x5 & CLC125 D 3x5 5.00 (127.0) 0.225 (5.72) 4.55 (115.57) 3.0 (76.2) 1.20 (30.5) Voltage Adj. 0.20 (5.10) J2 1.79 (45.4) J3 0.95 (24.1) 0.225 (5.72) 0.25 Faston Ground Tab 4 X ø.156 (3.96) Mounting Holes ø.312 (7.92) Clearance top and bottom J3 mates with Molex housing p/n 22-01-1024 and Molex series 5103 crimp terminals Input Connector J1 Molex PN 09-65-2038 Pin 1 Line Pin 2 Neutral J1 mates with Molex housing p/n 09-50-1031, and Molex series 5194 crimp terminals Output Connector J2 Molex PN 09-65-2048 Pin 1 +V1 Pin 2 +V1 Pin 3 RTN Pin 2 RTN 2.55 (64.77) 1.52 (38.6) Input Connector J1 Molex PN 09-65-2038 Pin 1 Line Pin 2 Neutral 0.20 (5.1) 0.13 (3.2) 0.14 (3.5) SMD Component Height J2 mates with Molex housing p/n 09-50-1041 and Molex series 5194 crimp terminals Fan Supply Connector J3 Molex PN 22-04-1021 Pin 1 Fan+ Pin 2 FanJ3 mates with Molex housing p/n 22-01-1024 and Molex series 5103 crimp terminals Notes 1. All dimensions in inches (mm). 2. Weight 0.386 lbs (175 g) 3. Tolerance .xx = ±0.02 (0.50); .xxx = ±0.01 (0.25) 21-Jan-11 ACDC CLC125 Models and Ratings