Series AM10CW-NZ 10 Watt | DC-DC Converter Picture coming soon FEATURES: Wide 4:1 Input Voltage Range High efficiency up to 88% 1500 VDC Isolation Over Current Protection No load consumption ≤ 0.12W Operating Temperature -40ºC to +85ºC Output Over Voltage protection Continuous Short Circuit Protection Input Under voltage Protection Remote On/Off control Models Single output Model Input Voltage (V) Output Voltage (V) Output Current max (A) Isolation (VDC) Max Capacitive Load (uF) Efficiency (%) AM10CW-2403S-NZ AM10CW-2405S-NZ AM10CW-2409S-NZ AM10CW-2412S-NZ AM10CW-2415S-NZ AM10CW-2424S-NZ AM10CW-4803S-NZ AM10CW-4805S-NZ AM10CW-4812S-NZ AM10CW-4815S-NZ AM10CW-4824S-NZ 9-36 9-36 9-36 9-36 9-36 9-36 18-75 18-75 18-75 18-75 18-75 3.3 5 9 12 15 24 3.3 5 12 15 24 2.4 2 1.11 0.83 0.66 0.41 2.4 2 0.83 0.66 0.41 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 2200 2200 680 470 330 100 2200 2200 470 330 100 79 83 86 87 87 88 79 83 87 87 88 Input Voltage (V) Output Voltage (V) Output Current max (A) Isolation (VDC) Max Capacitive Load (uF) Efficiency (%) Models Dual output Model AM10CW-2405D-NZ 9-36 ±5 ±1 1500 ±1000 83 AM10CW-2412D-NZ 9-36 ±12 ±0.41 1500 ±470 87 AM10CW-2415D-NZ 9-36 ±15 ±0.33 1500 ±330 87 AM10CW-2424D-NZ 9-36 ±24 ±0.2 1500 ±100 87 AM10CW-4805D-NZ 18-75 ±5 ±1 1500 ±1000 83 AM10CW-4812D-NZ 18-75 ±12 ±0.41 1500 ±470 87 AM10CW-4815D-NZ 18-75 ±15 ±0.33 1500 ±330 87 AM10CW-4824D-NZ 18-75 ±24 ±0.2 1500 ±100 87 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Voltage range Nominal Typical 24 Vin 48 Vin 9-36 18-75 Filter Absolute Maximum Rating (100ms) No Load Input Current Input reflected current Input Under voltage turn off Startup time Remote On/Off Control www.aimtec.com F 051e R13 Maximum Units VDC Pi 24 Vin 48 Vin 24 Vin 48 Vin 24 Vin 48 Vin 24 Vin 48 Vin Nominal input, resistive load On Off -0.7 - 50 -0.7 - 100 12 8 40 30 6.5 15.5 10 mA mA VDC ms 3.5-12VDC or leave open 0-1.2VDC or connect to GND, idle current 6-10mA Tel: +1 514 620 2722 1 of 3 VDC Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM10CW-NZ 10 Watt | DC-DC Converter Isolation Specifications Parameters Tested I/O voltage Resistance Capacitance Conditions Typical 60 sec, <1mA 500VDC I/O, 100KHz/0.1V 1500 Maximum Units >1000 VDC MOhm pF 1000 Output Specifications Parameters Voltage accuracy Voltage balance (Dual Output Models) Over voltage protection Over current protection Short Circuit protection Short circuit restart Line voltage regulation (Single) Line voltage regulation (Dual) Load voltage regulation (Single) Load voltage regulation (Dual) Cross Regulation (Dual Output Models) Temperature coefficient Ripple & Noise Transient recovery time Transient recovery deviation Conditions Typical Maximum Units 5% to 100% load Balanced Load ±2 ±3 ±1.5 % % % of Vout % of Iout ±0.5 ±1 ±1 ±1.5 % of Vin % of Vin % % 110-160 110-190 Continuous Auto-Recovery Full load, LL to HL Full load, LL to HL 5% to 100% load 5% to 100% load 50% load on one output & 10-100% load on second load 100% load 20MHz Bandwidth, 5-100% load 25% load step change 25% load step change ±5 % ±0.03 80 500 ±5 %/oC mV p-p µs % General Specifications Parameters Conditions Typical Switching frequency Operating temperature Storage temperature Maximum case temperature Cooling Humidity Case material Weight Dimensions (L x W x H) MTBF Maximum soldering temperature 100% load See derating curve 350 Maximum Units 100 KHz oC oC oC -40 to +85 -55 to +125 Free air convection 95 Aluminum Alloy 15 1 x 1 x 0.46 inches 25.40 x 25.40 x 11.70 mm o >1,000,000 hours (MIL-HDBK -217F, Ground Benign, t=+25 C) 1.5mm from case for 10 sec 300 % RH g oC Environmental Specifications Parameters Vibration Test mode Acceleration 10-55Hz 10G, 30min one cycle, every axis tested Safety Specifications Parameters Approval Standards www.aimtec.com F 051e R13 CE, UL, pending EN 55022, class B (with the recommended EMC circuit) Electrostatic Discharge Immunity IEC 61000-4-2, Contact ±4KV, Criteria B RF, Electromagnetic Field Immunity IEC 61000-4-3, 10V/m, Criteria A Electrical Fast Transient / Burst Immunity IEC 61000-4-4, ±2KV, Criteria B (with the recommended EMC circuit) Surge Immunity IEC 61000-4-5, ±2KV, Criteria B (with the recommended EMC circuit) RF, Conducted Disturbance Immunity IEC 61000-4-6, 3 Vrms, Criteria A Voltage dips, Short Interruptions & Voltage IEC 61000-4-29: 0-70%, Criteria B variations Immunity Tel: +1 514 620 2722 2 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM10CW-NZ 10 Watt | DC-DC Converter Pin Out Specifications Bottom View 2.54 (0.10) Top View 25.40 (1.00) 10.16 2.54 (0.40) (0.10) 10.16 (0.40) 5 4 +V Output 20.32 (0.80) 1 2 3 4 5 6 Dimensions Dual +V Input -V Input On/Off Control +V Output Common -V Output 25.40 (1.00) Single +V Input -V Input On/Off Control +V Output No pin -V Output Pin +V Input Derating 1 6 -V Output -V Input CTRL 2 3 65 ºC 3.3, 5V & ±5V models Side View 71ºC Other models 80 10.16 (0.40) 5.08 7.62 (0.20) (0.30) Printed Face 11.70 (0.46) 60 Safe Operating Area 40 2.54 (0.10) ᴓ 1.00 (0.39) 4.10 (0.16) Output Power (%) 100 2.54 (0.10) Free Air Convection 20 0 - 20 - 40 0 20 40 65 71 60 Dimensions mm (inch) Case Tolerance ±0.50 (±0.02) Pin Diameter 1.0 ± 0.10 (0.04 ± 0.004) 80 85 100 Ambient Temperature º C Recommended EMC Circuits CY1 1nF/2KV LDM 4.7µH F1 +Vin C1 MOV +Vo C3 C2 DC‐DC Converter ‐Vo ‐Vin CY2 1nF/2KV MOV C1 C2 C3 24V input S14K35 330µF/50V 1µF/50V 10µF/50V 48V input S14K60 330µF/100V 1µF/100V 10µF/100V NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R13 Tel: +1 514 620 2722 3 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only