SIDACtor ® Protection Thyristors SLIC Protection Battrax® Series - Single Port Negative - MS-013 Description The Battrax® series offers programmable SIDACtor® overvoltage protection devices for SLIC applications. The Single Port Negative Battrax Series provides a programmable device that is referenced to a negative voltage souce while internal diodes provide protection from positive surge events. Features and Benefits t Single-port protection t Low on-state voltage t Gate triggered tracking device t Does not degrade with use Agency Approvals Agency t Low voltage overshoot t Fails short circuit when surged in excess of ratings Agency File Number E133083 t Integrated diodes for positive voltage Applicable Global Standards Pinout Designation t TIA-968-A t GR 1089 Intra-building 1 6 t TIA-968-B t IEC 61000-4-5 2 5 t ITU K.20/21 Enhanced Level t YD/T 1082 3 4 t ITU K.20/21 Basic Level t YD/T 950 t YD/T 993 t GR 1089 Inter-building Schematic Symbol 6 (No Connect) (T) 1 (-VREF) 2 5 (G) 4 (No Connect) (R) 3 Electrical Characteristics Part Number Marking VDRM @lDRM=5μA VS @100V/μs V min V max IS IH mA min mA max IT VT @IT=2.2 Amps VF A max V max V max Capacitance* pF min pF max B1101UCLxx B1101UC I-VREF* *7* I-VREF* *7* 100 100 2.2 4 5 30 200 B1161UCLxx B1161UC I-VREF* *7* I-VREF* *7* 160 100 2.2 4 5 30 200 B1201UCLxx B1201UC I-VREF* *7* I-VREF* *7* 200 100 2.2 4 5 30 200 - VREF Max Value for the negative Battrax is -200 V. - XX = Part Number Suffix: ‘TP’ (Tube Pack) or ‘RP’ (Reel Pack). Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are uni-directional - All electrical characteristics shown are defined from Tip (pin 1) to Ground (pin 5), and Ring (pin 3) to Ground (pin 5) © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. * Off-state capacitance (CO) is measured across pins 1 & 5 and 3 & 5 at 1 MHz with a 2V bias. 118 Revised: February 22, 2011 SIDACtor ® Protection Thyristors SLIC Protection Surge Ratings Series IPP ITSM 50/60 Hz di/dt A min A min A/μs max 200 50 500 0.2x310 1 0.5x700 2 2x10 1 2x10 2 8x20 1 1.2x50 2 10x160 1 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 A min A min A min A min A min A min A min A min 50 500 400 200 150 200 175 100 C Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPPSBUJOHTBQQMJDBCMFPWFSUFNQFSBUVSFSBOHFPG$UP $ *PP rating assumes VREFFRVBMT 7 - The device must initially be in thermal equilibrium with -40°C < TJ < ¡$ 1 Current waveform in μs 2 Voltage waveform in μs Thermal Considerations Package Symbol Modified MS-013 6 Parameter Value Unit TJ Operating Junction Temperature Range UP °C TS Storage Temperature Range UP °C 60 °C/W 5 4 1 2 R0JA 3 Thermal Resistance: Junction to Ambient V-I Characteristics tr x td Pulse Waveform IPP – Peak Pulse Current – %IPP +I V VREF VS VDRM IF VT -V +V IDRM IH IS IT IPP 100 Waveform = tr x td 50 Half Value 0 PIN CONNECTED TO GROUND Pin51-2: PIN TOGROUND VREF PIN22CONNECTED CONNECTED TO -I tr = rise time to peak value td = decay time to half value Peak Value PIN 3 CONNECTED TO VREF 0 td tr t – Time (μs) Normalized DC Holding Current vs. Case Temperature Normalized VS Change vs. Junction Temperature IH 8 6 25 °C 4 2 IH (TC = 25ºC) 10 Ratio of Percent of VS Change – % 2.0 14 12 0 -4 -6 -8 -40 -20 0 1.6 1.4 25°C 1.2 1.0 0.8 0.6 0.4 20 40 60 80 100 120 140 160 -40 Junction Temperature (TJ) – °C © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 1.8 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC 119 Revised: February 22, 2011 SIDACtor ® Protection Thyristors SLIC Protection Soldering Parameters Pb-Free assembly (see Fig. 1) ¡$ ¡$ 60-180 secs. - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) Figure 1 TP ¡$ - Temperature (tL) 60-150 secs. Peak Temp (TP) tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition TL TS(max) tL Ramp-down Preheat TS(min) tS ¡$ 25 Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed time to peak temperature (t 25ºC to peak) ¡$ Time Environmental Specifications High Temp Voltage Blocking 80% Rated VREF Max. (VDC Peak ¡$PS ¡$ PSIST.*-45% .FUIPE 1040) JEDEC, JESD22-A-101 Temp Cycling ¡$UP ¡$ NJOEXFMM VQUP cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC ¡$ 3) VQUPIST&*" JEDEC, JESD22-A-101 High Temp Storage ¡$IST.*-45% .FUIPE JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock ¡$UP ¡$ NJOEXFMM TFDUSBOTGFS 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) ¡$ 3) BUN VQUPIST&*" JEDEC, JESD22-A-102 Resistance to Solder Heat ¡$ TFDT.*-45% .FUIPE Physical Specifications Lead Material Copper Alloy Terminal Finish 100% Matte-Tin Plated Body Material UL recognized epoxy meeting flammability classification 94V-0 Moisture Sensitivity Level Part Numbering 3) ¡$ IST SFnPXDZDMFT ¡$1FBL +&%&$+45% -FWFM Part Marking B1 xx 1 U C L xx TYPE B1: Negative Battrax SIDACtor HOLDING CURRENT 10: 100 mA 20: 200 mA 16: 160 mA CONSTRUCTION VARIABLE © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. PACKING OPTIONS RP: Reel Pack TP: Tube Pack XXXXXXX RoHS COMPLIANT Part Marking Code (Refer to Electrical Characteristics Table) Date Code IPP RATING XXXXX PACKAGE TYPE 120 Revised: February 22, 2011 SIDACtor ® Protection Thyristors SLIC Protection Dimensions — MS-013 Dimensions 0.065 (1.65) Pad Outline C 0.460 (11.68) 0.138 (3.50) Dimension are in inches (and millimeters). 0.059 (1.50) E D 7º TYP J 7º TYP A G Burr Side H 96º A Mold Split Line 4º A 7º TYP BSC* F MIN Length of Flat 7º TYP Detail A K B A B C D E F G H J K BSC* Inches Min Max Min Max 0.360 0.352 0.400 0.043 0.047 0.293 0.289 0.089 0.041 0.020 0.133 0.364 0.356 0.412 0.045 0.055 0.297 0.293 0.093 0.049 9.14 8.94 10.16 1.09 1.19 7.44 7.34 2.26 1.04 0.51 3.38 9.25 9.04 10.46 1.13 1.40 7.54 7.44 2.36 1.24 0.143 * BSC = Basic Spacing between Centers Packing Options Package Type U Description Quantity Added Suffix Industry Standard Modified MS-013 6-pin Tape and Reel Pack 1500 RP EIA-481-D Modified MS-013 6-pin Tube Pack 500 (50 per tube) TP N/A Tape and Reel Specification — MS-013 .157 (4.0) .630 (16.0) .472 (12.0) 12.99 (330) .512 (13.0) Arbor Hole Dia. Dimensions are in inches (and millimeters) 0.700 (17.8) Direction of Feed Tube Pack Specification — MS-013 Message Location .045 (1.14) .310 (7.87) 90˚ 6 Interior of the Tube .165 (4.19) .150 (3.81) .225 (5.72) .020 ± .005 WALL TYP. (0.51 ± 0.13) .108 (2.74) .005 A .110 (2.79) A Dimensions are in inches (and millimeters) .525 (13.34) © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 121 Revised: February 22, 2011 Millimeters 20.000 ± .030 (508.00 ± 0.76) 3.63