STMicroelectronics M74HCT273B1R Octal d type flip flop with clear Datasheet

M54HCT273
M74HCT273
OCTAL D TYPE FLIP FLOP WITH CLEAR
.
.
.
.
.
.
.
HIGH SPEED
fMAX = 80 MHz (TYP.) AT VCC = 5 V
LOW POWER DISSIPATION
ICC = 4 µA (MAX.) AT TA = 25 °C
COMPATIBLE WITH TTL OUTPUTS
VIH = 2V (MIN.) VIL = 0.8V (MAX)
OUTPUT DRIVE CAPABILITY
10 LSTTL LOADS
SYMMETRICAL OUTPUT IMPEDANCE
IOH = IOL = 4 mA (MIN.)
BALANCED PROPAGATION DELAYS
tPLH = tPHL
PIN AND FUNCTION COMPATIBLE WITH
54/74LS273
DESCRIPTION
The M54/74HCT273 is a high speed CMOS OCTAL
D-TYPE FLIP FLOP WITH CLEAR fabricated in sili2
con gate C MOS technology. It has the same high
speed performance of LSTTL combined with true
CMOS low power consumption. Information signals
applied to D inputs are transferred to the Q outputs
on the positive-going edge of the clock pulse.
When the CLEAR input is held low, the Q output are
in the low logic level independent of the other inputs.
All inputs are equipped with protection circuits
against static discharge and transient excess voltage. This integrated circuit has input and output
characteristics that are fully compatible with 54/74
LSTTL logic families. M54/74HCT devices are de2
signed to directly interface HSC MOS systems with
TTL and NMOS components. They are also plug in
replacements for LSTTL devices giving a reduction
of power consumption. All inputs are equipped with
protection circuits against static discharge and transient excess voltage.
B1R
(Plastic Package)
F1R
(Ceramic Package)
M1R
(Micro Package)
C1R
(Chip Carrier)
ORDER CODES :
M54HCT273F1R
M74HCT273M1R
M74HCT273B1R
M74HCT273C1R
PIN CONNECTIONS (top view)
INPUT AND OUTPUT EQUIVALENT CIRCUIT
NC =
No Internal
Connection
February 1993
1/10
M54/M74HCT273
PIN DESCRIPTION
IEC LOGIC SYMBOL
PIN No
SYMBOL
1
CLEAR
2, 5, 6, 9,
12, 15, 16,
19
3, 4, 7, 8,
13, 14, 17,
18
11
Q0 to Q7
Master Reset Input
(Active LOW)
Flip Flop Outputs
NAME AND FUNCTION
D0 to D7
Data Inputs
CLOCK
10
GND
Clock Input (LOW to
HIGH, Edge Triggered)
Ground (0V)
20
V CC
Positive Supply Voltage
TRUTH TABLE
CLEAR
INPUTS
CLOCK
D
L
X
FUNCTION
CLEAR
X
L
H
H
L
H
L
H
H
X
Qn
X: Don’t Care
LOGIC DIAGRAM
2/10
OUTPUS
QA
NO CHANGE
M54/M74HCT273
ABSOLUTE MAXIMUM RATINGS
Symbol
Value
Unit
VCC
VI
Supply Voltage
DC Input Voltage
-0.5 to +7
-0.5 to VCC + 0.5
V
V
VO
DC Output Voltage
-0.5 to VCC + 0.5
V
IIK
IOK
DC Input Diode Current
DC Output Diode Current
± 20
± 20
mA
mA
IO
DC Output Source Sink Current Per Output Pin
± 25
mA
DC VCC or Ground Current
± 50
mA
500 (*)
mW
ICC or IGND
Parameter
PD
Power Dissipation
Tstg
TL
Storage Temperature
Lead Temperature (10 sec)
-65 to +150
300
o
o
C
C
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition isnotimplied.
(*) 500 mW: ≅ 65 oC derate to 300 mW by 10mW/oC: 65 oC to 85 oC
RECOMMENDED OPERATING CONDITIONS
Symbol
VCC
Parameter
Supply Voltage
VI
Input Voltage
VO
Top
Output Voltage
Operating Temperature: M54HC Series
M74HC Series
Input Rise and Fall Time (VCC = 4.5 to 5.5V)
tr, tf
Value
4.5 to 5.5
Unit
V
0 to VCC
V
0 to VCC
-55 to +125
-40 to +85
0 to 500
V
C
o
C
ns
o
3/10
M54/M74HCT273
DC SPECIFICATIONS
Test Conditions
Symbol
Parameter
VCC
(V)
VIH
High Level Input
Voltage
4.5
to
5.5
V IL
Low Level Input
Voltage
4.5
to
5.5
V OH
High Level
Output Voltage
VOL
II
ICC
∆ICC
4/10
Low Level Output
Voltage
Input Leakage
Current
Quiescent Supply
Current
Additional worst
case supply
current
Value
TA = 25 oC
54HC and 74HC
Min. Typ. Max.
2.0
-40 to 85 oC -55 to 125 oC
74HC
54HC
Min. Max. Min. Max.
2.0
0.8
4.5
VI = IO=-20 µA
VIH
or IO=-4.0 mA
V IL
4.5
VI = IO= 20 µA
VIH
or IO= 4.0 mA
V IL
2.0
0.8
V
0.8
4.4
4.5
4.4
4.4
4.18
4.31
4.13
4.10
Unit
V
V
0.0
0.1
0.1
0.1
0.17
0.26
0.33
0.4
VI = VCC or GND
±0.1
±1
±1
µA
5.5
VI = VCC or GND
4
40
80
µA
5.5
Per Input pin
VI = 0.5V or
V I = 2.4V
Other Inputs at
V CC or GND
IO= 0
2.0
2.9
3.0
mA
5.5
V
M54/M74HCT273
AC ELECTRICAL CHARACTERISTICS (C L = 50 pF, Input t r = tf = 6 ns)
Test Conditions
Value
-40 to 85 oC -55 to 125 oC
74HC
54HC
Min. Max. Min. Max.
19
22
Symbol
Parameter
VCC
(V)
tTLH
tTHL
tPLH
tPHL
Output Transition
Time
Propagation
Delay Time
(CLOCK - Q)
Propagation
Delay Time
(CLEAR - Q)
Maximum Clock
Frequency
Input Capacitance
Power Dissipation
Capacitance
4.5
TA = 25 oC
54HC and 74HC
Min. Typ. Max.
9
15
4.5
19
30
38
45
ns
4.5
22
32
40
48
ns
tPLH
tPHL
fMAX
CIN
CPD (*)
4.5
30
71
5
29
24
10
Unit
ns
MHz
10
10
pF
pF
(*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load.
(Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC(opr) = CPD •VCC •fIN + ICC/8 (per Flip FLop), and the
total CPD when n pcs of Flip Flop operate can be gained by the following equations: CPD (total) = 32 + 11 x n
SWITCHING CHARACTERISTICS TEST WAVEFORM
TEST CIRCUIT ICC (Opr.)
5/10
M54/M74HCT273
Plastic DIP20 (0.25) MECHANICAL DATA
mm
DIM.
MIN.
a1
0.254
B
1.39
TYP.
inch
MAX.
MIN.
TYP.
MAX.
0.010
1.65
0.055
0.065
b
0.45
0.018
b1
0.25
0.010
D
25.4
1.000
E
8.5
0.335
e
2.54
0.100
e3
22.86
0.900
F
7.1
0.280
I
3.93
0.155
L
Z
3.3
0.130
1.34
0.053
P001J
6/10
M54/M74HCT273
Ceramic DIP20 MECHANICAL DATA
mm
DIM.
MIN.
TYP.
inch
MAX.
MIN.
TYP.
MAX.
A
25
0.984
B
7.8
0.307
D
E
3.3
0.5
e3
0.130
1.78
0.020
22.86
0.070
0.900
F
2.29
2.79
0.090
0.110
G
0.4
0.55
0.016
0.022
I
1.27
1.52
0.050
0.060
L
0.22
0.31
0.009
0.012
M
0.51
1.27
0.020
0.050
N1
P
Q
4° (min.), 15° (max.)
7.9
8.13
5.71
0.311
0.320
0.225
P057H
7/10
M54/M74HCT273
SO20 MECHANICAL DATA
mm
DIM.
MIN.
TYP.
A
a1
inch
MAX.
MIN.
TYP.
2.65
0.10
0.104
0.20
a2
MAX.
0.004
0.007
2.45
0.096
b
0.35
0.49
0.013
0.019
b1
0.23
0.32
0.009
0.012
C
0.50
0.020
c1
45° (typ.)
D
12.60
13.00
0.496
0.512
E
10.00
10.65
0.393
0.419
e
1.27
0.050
e3
11.43
0.450
F
7.40
7.60
0.291
0.299
L
0.50
1.27
0.19
0.050
M
S
0.75
0.029
8° (max.)
P013L
8/10
M54/M74HCT273
PLCC20 MECHANICAL DATA
mm
DIM.
MIN.
TYP.
inch
MAX.
MIN.
TYP.
MAX.
A
9.78
10.03
0.385
0.395
B
8.89
9.04
0.350
0.356
D
4.2
4.57
0.165
0.180
d1
2.54
0.100
d2
0.56
0.022
E
7.37
8.38
0.290
0.330
e
1.27
0.050
e3
5.08
0.200
F
0.38
0.015
G
0.101
0.004
M
1.27
0.050
M1
1.14
0.045
P027A
9/10
M54/M74HCT273
Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No
license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned
in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied.
SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express
written approval of SGS-THOMSON Microelectonics.
 1994 SGS-THOMSON Microelectronics - All Rights Reserved
SGS-THOMSON Microelectronics GROUP OF COMPANIES
Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A
10/10
Similar pages