CY2SSTU877 PRELIMINARY 1.8V, 500-MHz, 10-Output JEDEC-Compliant Zero Delay Buffer Features distributes a differential clock input pair (CK, CK#) to ten differential pair of clock outputs (Y[0:9], Y#[0:9]) and one differential pair of feedback clock outputs (FBOUT, FBOUT#). • Operating frequency: 125 MHz to 500 MHz The input clocks (CK, CK#), the feedback clocks (FBIN, FBIN#), the LVCMOS (OE, OS), and the analog power input (AVDD) control the clock outputs. • Supports DDRII SDRAM • 1 to 10 differential clock buffer (SSTL_18) • Spread-Spectrum-compatible • Low jitter (cycle-to-cycle): 40 ps • Very low output-to-output skew: 40 ps • Auto power-down feature when input is low • 1.8V operation • Fully JEDEC-compliant (JESD 82-8) • 52-ball BGA Functional Description The CY2SSTU877 is a high-performance, low-skew, low-jitter zero delay buffer designed to distribute differential clocks in high-speed applications. This phase-locked loop (PLL) clock buffer is designed for a VDD of 1.8V, an AVDD of 1.8V and SSTL18 differential data input and output levels. This device is a zero delay buffer that The PLL in the CY2SSTU877 clock driver uses the input clocks (CK, CK#) and the feedback clocks (FBIN, FBIN#) to provide high-performance, low-skew, low-jitter output differential clocks (Y[0:9], Y#[0:9]). The CY2SSTU877 is also able to track Spread Spectrum Clocking (SSC) for reduced EMI. When AVDD is grounded, the PLL is turned off and bypassed for test purposes. When both clock signals (CK, CK#) are logic low, the device will enter a low-power mode. An input logic detection circuit on the differential inputs, independent from the input buffers, will detect the logic low level and perform a low-power state where all outputs, the feedback, and the PLL are OFF. When the inputs transition from both being logic low to being differential signals, the PLL will be turned back on, the inputs and outputs will be enabled and the PLL will obtain phase lock between the feedback clock pair (FBIN, FBIN#) and the input clock pair (CK, CK#) within the specified stabilization time tL. Pin Configuration Block Diagram A B C D E F G H J K 1 2 3 4 5 6 CLKT1 CLKT0 CLKC0 CLKC5 CLKT5 CLKT6 CLKC1 GND GND GND GND CLKC6 CLKC2 GND NB NB GND CLKC7 CLKT2 VDDQ VDDQ VDDQ OS CLKT7 CLK_INT VDDQ NB NB VDDQ FB_INT CLK_INC VDDQ NB NB OE FB_INC AGND VDDQ VDDQ VDDQ VDDQ FB_OUTC FB_OUTT AVDD GND NB NB GND CLKT3 GND GND GND GND CLKT8 CLKC3 CLKC4 CLKT4 CLKT9 CLKC9 CLKC8 52 BGA Cypress Semiconductor Corporation Document #: 38-07575 Rev. *E • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised January 27, 2006 CY2SSTU877 PRELIMINARY Pin Description Pin No. Name Description G1 AGND Ground for 1.8V analog supply H1 AVDD 1.8V analog supply E1, F1 CLK_INT, CLK_INC Differential clock input with a (10K–100KΩ) pull-down resistor E6, F6 FB_INT, FB_INC Feedback differential clock input H6, G6 FB_OUTT, FB_OUTC Feedback differential clock output B2, B3, B4, B5, C2, C5, H2, H5, J2, J3, J4, GND J5 Ground F5 OE Output enable (ASYNC) for CLKT[0:9] and CLKC [0:9] D5 OS Output Select (Tied to GND or VDDQ) D2, D3, D4, E2, E5, F2, G2, G3, G4, G5 VDDQ 1.8V supply A2, A1, D1, J1, K3, A5, A6, D6, J6, K4, CLKT [0:9] Buffered output of input clock, CLK A3, B1, C1, K1, K2, A4, B6, C6, K6, K5 CLKC [0:9] Buffered output of input clock, CLK Table 1. Function Table Inputs Outputs AVDD OE OS GND H X CLK_INT CLK_INC L GND H X H L GND L H L H GND L L H L Lz,CLKT7 Active VDD L H L H Lz VDD L L H L Lz,CLKT7 Active VDD H X L H L H VDD H X H L H L VDD X X L L Lz Lz X X X H H H CLKT CLKC L H FB_OUTT FB_OUTC L H L H L Bypassed/Off Lz Lz L H Bypassed/Off Lz,CLKC7 Active H L Bypassed/Off Lz L H On Lz,CLKC7 Active H L On L H On H L On Lz Lz Off H PLL Bypassed/Off Reserved Recommended Operating Conditions Parameter Description TA (Com.) Ambient Operating Temp VDD, AVDD Operating Voltage Document #: 38-07575 Rev. *E Condition Min. Max. Unit 0 70 °C 1.7 1.9 V Page 2 of 9 CY2SSTU877 PRELIMINARY Absolute Maximum Conditions Parameter Description Condition Min. Max. Unit VIN Input Voltage Range –0.5 VDDQ + 0.5 V VOUT Output Voltage Range –0.5 VDDQ + 0.5 V TS Storage Temperature –65 150 °C VCC, AVCC Supply Voltage Range –0.5 2.5 V IIK Input Clamp Current –50 50 mA IOK Output Clamp Current –50 50 mA IO Continuous Output Current –50 50 mA Continuous Current through VDD/GND –100 100 mA DC Electrical Specifications Parameter Description VIK Input Clamping Voltage VOD Output Differential Voltage VOX Output Differential Crossing Voltage VIX Input Differential Crossing Voltage Conditions Min. II = –18 mA Max. Unit –1.2 V 0.5 V VDDQ/2 – 0.08 VDDQ/2 + 0.08 V (VDDQ/2) – 0.15 (VDDQ/2) + 0.15 V VID DC Input Differential Voltage (DC Values) 0.3 VDDQ + 0.4 V VID AC Input Differential Voltage (AC Values) 0.6 VDDQ + 0.4 V VIL Input Low Voltage (OE, OS, CLK_INT, CLK_INC) 0.35 * VDDQ V VIH Input High Voltage (OE, OS, CLK_INT, CLK_INC) VOL Output Low Voltage IOL = 100 µA 0.1 V IOL = 9 mA 0.6 V VOH Output High Voltage IOH = –100 µA IOH = –9 mA 0.65 * VDDQ V VDDQ – 0.2 V 1.1 V IIH Input High Current VIN = VDDQ or GND –250 250 µA IIL Input Low Current VIN = VDDQor GND –10 10 µA IODL Output disabled low current VODL= 100 mV OE = GND 100 IDDLD Static Supply current IDDQ + IADD, CLK_INT = CLK_INC = GND 500 µA CL = 0 @ 270 MHz 300 mA –9 mA 9 mA 3 pF IDD Dynamic Supply Current IOH Output High Current IOL Output Low Current CIN Input Capacitance COUT CIN(DELTA) Document #: 38-07575 Rev. *E (Input Capacitance of CLK_INT, CLK_INC, FB_INT, FB_INC) VI = VDDQ or GND 2 Ci(delta) (CLK_INT, CLK_INC, FB_INT, FB_INC) VI = VDDQ or GND –0.25 µA pF 0.25 pF Page 3 of 9 CY2SSTU877 PRELIMINARY AC Timing Specifications Parameter FCLK [1,2] Description Conditions Min. Max. Unit Clock Frequency (Max) Room temp and nominal VDDQ 125 500 MHz Clock Frequency (Application) Room temp and nominal VDDQ 250 500 MHz TDC Input Duty Cycle 40 60 % TODC Output Duty Cycle 48 52 % TLOCK PLL Lock Time – 15 µs TOENB Output Enable Time OE to any CLKT/ CLKC[0:9] – 8 ns TODIS Output Disable Time OE to any CLKT/ CLKC[0:9] – 8 ns Tjitt (cc) Cycle-to-cycle jitter –40 40 ps Tjit (Period) Period jitter –30 30 ps Tjit (H-Period) Half Period Cycle-to-cycle jitter Above 270 MHz –45 45 ps Below 270 MHz –60 60 ps Average 1000 cycles –50 50 ps –40 40 ps T(φ) Static Phase Offset T(φ)DYN Dynamic Phase Offset TSKEW Clock Skew – 40 ps SLR(O) Output Slew Rate CLKT/ CLKC[0:9], FB_OUTT, FB_OUTC 1.5 4 V/ns SLR(I) Input Slew Rate CLK_INT, CLK_INC, FB_INT, FB_INC 1 4 V/ns OE 0.5 V/ns Figure 1. Test Loads for Timing Measurement Notes: 1. Operating clock frequency indicates a range over which the PLL must be able to lock, but in which it is not required to meet the other timing parameters (used for low speed system debug). 2. Application clock frequency indicates a range over which the PLL must meet all timing requirements. Document #: 38-07575 Rev. *E Page 4 of 9 CY2SSTU877 PRELIMINARY - Figure 2. Cycle-to-cycle Jitter tjit(per) - Figure 3. Period Jitter - Figure 4. Half Period Jitter Document #: 38-07575 Rev. *E Page 5 of 9 PRELIMINARY CY2SSTU877 Figure 5. Static Phase Offset (Differential Probes) Figure 6. Dynamic Phase Offset (Differential Probes) Figure 7. Output Skew Document #: 38-07575 Rev. *E Page 6 of 9 CY2SSTU877 PRELIMINARY CLKT/CLKC CLKT CLKC Figure 8. Output Enable and Disable Times CLKT CLKC Figure 9. Input/Output Slew Rates CARD VIA R1 Bead AVDD VDDQ 1Ω 4.7 pF 1206 0.1 µF 0603 2200 pF 0603 PLL GND AGND CARD VIA Figure 10. AVDD Filtering[3,4,5] Ordering Information Part Number Package Type Product Flow Lead-free and ROHS Compliant CY2SSTU877BVXC-32 52-pin VFBGA for DDR400 Commercial, 0° to 70°C CY2SSTU877BVXC-32T 52-pin VFBGA for DDR400 – Tape& Reel Commercial, 0° to 70°C CY2SSTU877BVXI-32 52-pin VFBGA for DDR400 CY2SSTU877BVXI-32T 52-pin VFBGA for DDR400 – Tape& Reel Industrial, –40° to 85°C CY2SSTU877BVXC-43 52-pin VFBGA for DDR533 Industrial, –40° to 85°C Commercial, 0° to 70°C CY2SSTU877BVXC-43T 52-pin VFBGA for DDR533 – Tape& Reel Commercial, 0° to 70°C CY2SSTU877BVXI-43 52-pin VFBGA for DDR533 CY2SSTU877BVXI-43T 52-pin VFBGA for DDR533 – Tape& Reel Industrial, –40° to 85°C Industrial, –40° to 85°C Notes: 3. Place the 2200-pF capacitor close to the PLL. 4. Use a wide trace for the PLL analog power and ground. Connect PLL & Caps to AGND trace & connect trace to one GND via (farthest from PLL). 5. Recommended bead: Fair-Rite P/N 2506036017Y0 or equivalent (0.9 ohm DC max, 600 ohms@100 MHz). Document #: 38-07575 Rev. *E Page 7 of 9 CY2SSTU877 PRELIMINARY Package Drawing 52 VFBGA 4.5 × 7.0 × 1.0 MM BV52A TOP VIEW BOTTOM VIEW A1 CORNER Ø0.05 M C Ø0.25 M C A B Ø0.30±0.05(52X) A1 CORNER 1 2 3 4 5 6 6 3 2 1 B C C 0.65 A B E F F G 2.925 G D E 5.85 7.00±0.10 D 7.00±0.10 4 5 A H H J J K K 1.625 A A B 4.50±0.10 0.65 3.25 DIMENSION IN MM REFERENCE JEDEC MO-225 SEATING PLANE C 1.00 MAX 0.26 MAX. 4.50±0.10 0.15 C 0.21±0.05 0.55 MAX. 0.25 C B 0.15(4X) 51-85192-** All product and company names mentioned in this document are the trademarks of their respective holders. Document #: 38-07575 Rev. *E Page 8 of 9 © Cypress Semiconductor Corporation, 2006. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. CY2SSTU877 PRELIMINARY Document History Page Document Title:CY2SSTU877 1.8V, 500-MHz, 10-Output JEDEC-Compliant Zero Delay Buffer Document Number: 38-07575 Rev. ECN No. Issue Date Orig. of Change Description of Change ** 129198 08/22/03 RGL New Data Sheet *A 204389 See ECN RGL Added more Information. Deleted 4 rows from the bottom of the Pin description. *B 310414 See ECN RGL Changed Advance Info. to Preliminary status Added Lead-free devices *C 324113 See ECN RGL Data sheet re-write *D 404547 See ECN RGL Added speed bins to part number *E 424024 See ECN RGL Swap pins 6G and 6H Document #: 38-07575 Rev. *E Page 9 of 9