CAT5409 Quad Digitally Programmable Potentiometers (DPP™) with 64 Taps and I²C Interface FEATURES DESCRIPTION Four linear taper digitally programmable potentiometers 64 resistor taps per potentiometer End to end resistance 2.5 kΩ, 10 kΩ, 50 kΩ or 100 kΩ I²C interface Low wiper resistance, typically 80 Ω Four non-volatile wiper settings for each potentiometer Recall of saved wiper settings at power-up 2.5 to 6.0 volt operation Standby current less than 1 µA 1,000,000 nonvolatile WRITE cycles 100 year nonvolatile memory data retention 24-lead SOIC and 24-lead TSSOP Write protection for data register The CAT5409 is four Digitally Programmable Potentiometers (DPP™) integrated with control logic and 16 bytes of NVRAM memory. A separate 6-bit control register (WCR) independently controls the wiper tap position for each DPP. Associated with each wiper control register are four 6-bit non-volatile memory data registers (DR) used for storing up to four wiper settings. Writing to the wiper control register or any of the non-volatile data registers is via a I²C serial bus. On power-up, the contents of the first data register (DR0) for each of the four potentiometers is automatically loaded into its respective wiper control register (WCR). ¯¯¯) pin protects against The Write Protection (WP inadvertent programming of the data register. The CAT5409 can be used as a potentiometer or as a two terminal, variable resistor. It is intended for circuit level or system level adjustments in a wide variety of applications. For Ordering Information details, see page 15. PIN CONFIGURATION FUNCTIONAL DIAGRAM SOIC (W) TSSOP (Y) RH0 SDA 1 24 WP VCC 1 24 NC A1 2 23 A2 RL0 2 23 RL3 RL1 3 22 RW0 RH0 3 22 RH3 RH1 4 21 RH0 RW0 4 21 RW3 RW1 5 20 RL0 A2 5 20 A0 GND 6 19 VCC WP 6 19 NC NC 7 18 NC SDA 7 18 A3 RW2 8 17 RL3 A1 8 17 SCL RH2 9 16 RH3 RL1 9 16 RL2 RL2 10 15 RW3 RH1 10 15 RH2 SCL 11 14 RW1 11 14 A3 12 A0 13 NC © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice GND 12 SCL SDA I²C BUS INTERFACE RH1 RH2 RH3 WIPER CONTROL REGISTERS RW0 RW1 WP A0 A1 A2 A3 CONTROL LOGIC NONVOLATILE DATA REGISTERS RW2 RW3 RL0 RL1 RL2 RL3 RW2 13 NC 1 Doc. No. MD-2010 Rev. M CAT5409 PIN DESCRIPTIONS Pin# (SOIC) Pin# (TSSOP) Name 19 1 VCC 20 2 RL0 21 3 RH0 22 4 RW0 23 24 1 2 5 6 7 8 A2 ¯¯¯ WP SDA A1 3 9 RL1 4 10 RH1 5 11 RW1 6 7 12 13 GND NC 8 14 RW2 9 15 RH2 10 16 RL2 11 12 13 14 17 18 19 20 SCL A3 NC A0 15 21 RW3 16 22 RH3 17 23 RL3 18 24 NC SCL: Serial Clock The CAT5409 serial clock input pin is used to clock all data transfers into or out of the device. Function Supply Voltage Low Reference Terminal for Potentiometer 0 High Reference Terminal for Potentiometer 0 Wiper Terminal for Potentiometer 0 Device Address SDA: Serial Data The CAT5409 bidirectional serial data pin is used to transfer data into and out of the device. The SDA pin is an open drain output and can be wire-Ored with the other open drain or open collector outputs. A0, A1, A2, A3: Device Address Inputs These inputs set the device address when addressing multiple devices. A total of sixteen devices can be addressed on a single bus. A match in the slave address must be made with the address input in order to initiate communication with the CAT5409. Write Protection Serial Data Input/Output Device Address Low Reference Terminal for Potentiometer 1 High Reference Terminal for Potentiometer 1 Wiper Terminal for Potentiometer 1 Ground RH, RL: Resistor End Points The four sets of RH and RL pins are equivalent to the terminal connections on a mechanical potentiometer. RW: Wiper The four RW pins are equivalent to the wiper terminal of a mechanical potentiometer. No Connect Wiper Terminal for Potentiometer 2 High Reference Terminal for Potentiometer 2 Low Reference Terminal for Potentiometer 2 Bus Serial Clock ¯¯¯ WP: Write Protect Input The ¯¯¯ WP pin when tied low prevents non-volatile writes to the data registers (change of wiper control register is allowed) and when tied high or left floating normal read/write operations are allowed. See Write Protection on page 7 for more details. Device Address No Connect Device Address, LSB Wiper Terminal for Potentiometer 3 High Reference Terminal for Potentiometer 3 Low Reference Terminal for Potentiometer 3 No Connect DEVICE OPERATION The CAT5409 is four resistor arrays integrated with I²C serial interface logic, four 6-bit wiper control registers and sixteen 6-bit, non-volatile memory data registers. Each resistor array contains 63 separate resistive elements connected in series. The physical ends of each array are equivalent to the fixed terminals of a mechanical potentiometer (RH and RL). RH and RL are symmetrical and may be interchanged. The tap positions between and at the ends of the series resistors are connected to the output wiper terminals (RW) by a CMOS transistor switch. Only one tap point for each potentiometer is connected to its wiper terminal at a time and is determined by the value of the wiper control register. Data can be read or written to the wiper control registers or the non-volatile memory data registers via the I²C bus. Additional instructions allows data to be transferred between the wiper control registers and each respective potentiometer's non-volatile data registers. Also, the device can be instructed to operate in an "increment/decrement" mode. Doc. No. MD-2010 Rev. M 2 © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice CAT5409 ABSOLUTE MAXIMUM RATINGS(1) Parameters Temperature Under Bias Storage Temperature Voltage on Any Pin with Respect to VSS(1) (2) VCC with Respect to Ground Package Power Dissipation Capability (TA = 25ºC) Lead Soldering Temperature (10 s) Wiper Current Ratings -55 to +125 -65 to +150 -2.0 to +VCC + 2.0 -2.0 to +7.0 1.0 300 ±12 Units ºC °C V V W ºC mA Ratings +2.5 to +6 -40 to +85 Units V °C RECOMMENDED OPERATING CONDITIONS Parameters VCC Industrial Temperature POTENTIOMETER CHARACTERISTICS Over recommended operating conditions unless otherwise stated. Symbol RPOT RPOT RPOT RPOT IW RW RW VTERM TCRPOT TCRATIO CH/CL/CW fc Parameter Potentiometer Resistance (-00) Potentiometer Resistance (-50) Potentiometer Resistance (-10) Potentiometer Resistance (-2.5) Potentiometer Resistance Tolerance RPOT Matching Power Rating Wiper Current Wiper Resistance Wiper Resistance Voltage on any RH or RL Pin Resolution Absolute Linearity (5) Relative Linearity (6) Temperature Coefficient of RPOT Ratiometric Temp. Coefficient Potentiometer Capacitances Frequency Response Test Conditions Min Typ Max 100 50 10 2.5 25°C, each pot IW = ±3 mA @ VCC = 3 V IW = ±3 mA @ VCC = 5 V VSS = 0 V 80 GND kΩ kΩ kΩ kΩ ±20 % 1 50 ±6 300 150 VCC % mW mA Ω Ω V % LSB (7) LSB (7) ppm/ºC ppm/ºC pF MHz 1.6 RW(n)(actual) - R(n)(expected)(8) RW(n+1) - [RW(n) + LSB](8) (4) (4) (4) RPOT = 50 kΩ (4) ±1 ±0.2 ±300 20 10/10/25 0.4 Units Notes: (1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability. (2) The minimum DC input voltage is –0.5 V. During transitions, inputs may undershoot to –2.0 V for periods of less than 20 ns. Maximum DC voltage on output pins is VCC +0.5 V, which may overshoot to VCC +2.0 V for periods of less than 20 ns. (3) Latch-up protection is provided for stresses up to 100 mA on address and data pins from –1 V to VCC +1 V. (4) This parameter is tested initially and after a design or process change that affects the parameter. (5) Absolute linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when used as a potentiometer. (6) Relative linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a potentiometer. It is a measure of the error in step size. (7) LSB = RTOT / 63 or (RH - RL) / 63, single pot. (8) n = 0, 1, 2, ..., 63 © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice 3 Doc. No. MD-2010 Rev. M CAT5409 D.C. OPERATING CHARACTERISTICS Over recommended operating conditions unless otherwise stated. Symbol Parameter Test Conditions ICC Power Supply Current ISB Min Max Units fSCL = 400 kHz 1 mA Standby Current (VCC = 5 V) VIN = GND or VCC, SDA Open 1 µA ILI Input Leakage Current VIN = GND to VCC 10 µA ILO Output Leakage Current VOUT = GND to VCC 10 µA VIL Input Low Voltage -1 VCC x 0.3 V VIH Input High Voltage VCC x 0.7 VCC + 1.0 V VOL1 Output Low Voltage (VCC = 3 V) 0.4 V IOL = 3 mA CAPACITANCE (1) TA = 25ºC, f = 1.0 MHz, VCC = 5 V Symbol Test Conditions Max. Units CI/O Input/Output Capacitance (SDA) VI/O = 0 V 8 pF CIN Input Capacitance (A0, A1, A2, A3, SCL, ¯¯¯ WP) VIN = 0 V 6 pF A.C. CHARACTERISTICS Over recommended operating conditions unless otherwise stated. Symbol Max Units Clock Frequency 400 kHz TI Noise Suppression Time Constant at SCL, SDA Inputs 50 ns tAA SLC Low to SDA Data Out and ACK Out 0.9 µs fSCL (1) Parameter Min Typ tBUF(1) Time the bus must be free before a new transmission can start 1.2 µs tHD:STA Start Condition Hold Time 0.6 µs tLOW Clock Low Period 1.2 µs tHIGH Clock High Period 0.6 µs tSU:STA Start Condition SetupTime (for a Repeated Start Condition) 0.6 µs tHD:DAT Data in Hold Time 0 ns tSU:DAT Data in Setup Time 100 ns (1) SDA and SCL Rise Time 0.3 µs (1) SDA and SCL Fall Time 300 ns tR tF tSU:STO tDH Stop Condition Setup Time 0.6 µs Data Out Hold Time 50 ns POWER UP TIMING (1) Symbol Parameter Max Units tPUR Power-up to Read Operation 1 ms tPUW Power-up to Write Operation 1 ms Note: (1) This parameter is tested initially and after a design or process change that affects the parameter. Doc. No. MD-2010 Rev. M 4 © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice CAT5409 WRITE CYCLE LIMITS Symbol Parameter tWR Max Units 5 ms Write Cycle Time The write cycle is the time from a valid stop condition of a write sequence to the end of the internal program/erase cycle. During the write cycle, the bus interface circuits are disabled, SDA is allowed to remain high, and the device does not respond to its slave address. RELIABILITY CHARACTERISTICS Symbol NEND (1) TDR(1) VZAP(1) ILTH(1) (2) Parameter Reference Test Method Min Max Units Endurance MIL-STD-883, Test Method 1033 1,000,000 Cycles/Byte Data Retention MIL-STD-883, Test Method 1008 100 Years ESD Susceptibility MIL-STD-883, Test Method 3015 2000 V Latch-Up JEDEC Standard 17 100 mA Figure 1. Bus Timing tF tHIGH tLOW tR tLOW SCL tSU:STA tHD:STA tHD:DAT tSU:DAT tSU:STO SDA IN tAA tBUF tDH SDA OUT Figure 2. Write Cycle Timing SCL SDA 8TH BIT ACK BYTE n tWR STOP CONDITION START CONDITION ADDRESS Figure 3. Start/Stop Timing SDA SCL START CONDITION STOP CONDITION Notes: (1) This parameter is tested initially and after a design or process change that affects the parameter. (2) tPUR and tPUW are delays required from the time VCC is stable until the specified operation can be initiated. © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice 5 Doc. No. MD-2010 Rev. M CAT5409 most significant bits of the 8-bit slave address are fixed as 0101 for the CAT5409 (see Figure 5). The next four significant bits (A3, A2, A1, A0) are the device address bits and define which device the Master is accessing. Up to sixteen devices may be individually addressed by the system. Typically, +5 V and ground are hard-wired to these pins to establish the device's address. SERIAL BUS PROTOCOL The following defines the features of the I²C bus protocol: (1) Data transfer may be initiated only when the bus is not busy. (2) During a data transfer, the data line must remain stable whenever the clock line is high. Any changes in the data line while the clock is high will be interpreted as a START or STOP condition. After the Master sends a START condition and the slave address byte, the CAT5409 monitors the bus and responds with an acknowledge (on the SDA line) when its address matches the transmitted slave address. The device controlling the transfer is a master, typically a processor or controller, and the device being controlled is the slave. The master will always initiate data transfers and provide the clock for both transmit and receive operations. Therefore, the CAT5409 will be considered a slave device in all applications. Acknowledge After a successful data transfer, each receiving device is required to generate an acknowledge. The Acknowledging device pulls down the SDA line during the ninth clock cycle, signaling that it received the 8 bits of data. START Condition The START Condition precedes all commands to the device, and is defined as a HIGH to LOW transition of SDA when SCL is HIGH. The CAT5409 monitors the SDA and SCL lines and will not respond until this condition is met. The CAT5409 responds with an acknowledge after receiving a START condition and its slave address. If the device has been selected along with a write operation, it responds with an acknowledge after receiving each 8-bit byte. STOP Condition A LOW to HIGH transition of SDA when SCL is HIGH determines the STOP condition. All operations must end with a STOP condition. When the CAT5409 is in a READ mode it transmits 8 bits of data, releases the SDA line, and monitors the line for an acknowledge. Once it receives this acknowledge, the CAT5409 will continue to transmit data. If no acknowledge is sent by the Master, the device terminates data transmission and waits for a STOP condition. DEVICE ADDRESSING The bus Master begins a transmission by sending a START condition. The Master then sends the address of the particular slave device it is requesting. The four Figure 4. Acknowledge Timing SCL FROM MASTER 1 8 9 DATA OUTPUT FROM TRANSMITTER DATA OUTPUT FROM RECEIVER ACKNOWLEDGE START Doc. No. MD-2010 Rev. M 6 © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice CAT5409 host's write operation, the CAT5409 initiates the internal write cycle. ACK polling can be initiated immediately. This involves issuing the start condition followed by the slave address. If the CAT5409 is still busy with the write operation, no ACK will be returned. If the CAT5409 has completed the write operation, an ACK will be returned and the host can then proceed with the next instruction operation. WRITE OPERATIONS In the Write mode, the Master device sends the START condition and the slave address information to the Slave device. After the Slave generates an acknowledge, the Master sends the instruction byte that defines the requested operation of CAT5409. The instruction byte consist of a four-bit opcode followed by two register selection bits and two pot selection bits. After receiving another acknowledge from the Slave, the Master device transmits the data to be written into the selected register. The CAT5409 acknowledges once more and the Master generates the STOP condition, at which time if a non-volatile data register is being selected, the device begins an internal programming cycle to non-volatile memory. While this internal cycle is in progress, the device will not respond to any request from the Master device. WRITE PROTECTION The Write Protection feature allows the user to protect against inadvertent programming of the non-volatile data registers. If the ¯¯¯ WP pin is tied to LOW, the data registers are protected and become read only. Similarly, the ¯¯¯ WP pin going low after start but after start will interrupt non-volatile write to data registers, while the ¯¯¯ WP pin going low after internal write cycle has started, will have no effect on any write operation. The CAT5409 will accept both slave addresses and instructions, but the data registers are protected from programming by the device’s failure to send an acknowledge after data is received. Acknowledge Polling The disabling of the inputs can be used to take advantage of the typical write cycle time. Once the stop condition is issued to indicate the end of the Figure 5. Slave Address Bits CAT5409 0 1 0 1 A3 * A0, A1, A2 and A3 correspond to pin A0, A1, A2 and A3 of the device. ** A0, A1, A2 and A3 must compare to its corresponding hard wired input pins. A2 A1 A0 Figure 6. Write Timing BUS ACTIVITY: MASTER SDA LINE S T A R T INSTRUCTION BYTE SLAVE/DPP ADDRESS Fixed Variable op code DR1 WCRDATA P S A C K © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice Register Pot/WCR Address Address S T O P A C K 7 A C K Doc. No. MD-2010 Rev. M CAT5409 INSTRUCTION AND REGISTER DESCRIPTION INSTRUCTION BYTE The next byte sent to the CAT5409 contains the instruction and register pointer information. The four most significant bits used provide the instruction opcode I [3:0]. The R1 and R0 bits point to one of the four data registers of each associated potentiometer. The least two significant bits point to one of four Wiper Control Registers. The format is shown in Table 2. SLAVE ADDRESS BYTE The first byte sent to the CAT5409 from the master/ processor is called the Slave/DPP Address Byte. The most significant four bits of the Device Type address are a device type identifier. These bits for the CAT5409 are fixed at 0101[B] (refer to Table 1). The next four bits, A3 - A0, are the internal slave address and must match the physical device address which is defined by the state of the A3 - A0 input pins for the CAT5409 to successfully continue the command sequence. Only the device which slave address matches the incoming device address sent by the master executes the instruction. The A3 - A0 inputs can be actively driven by CMOS input signals or tied to VCC or VSS. Data Register Selection Data Register Selected R1 R0 DR0 0 0 DR1 0 1 DR2 1 0 DR3 1 1 Table 1. Identification Byte Format Device Type Identifier ID3 0 ID2 1 ID1 0 Slave Address ID0 1 A3 A2 A1 (MSB) A0 (LSB) Table 2. Instruction Byte Format Instruction Opcode I3 (MSB) Doc. No. MD-2010 Rev. M I2 Data Register Selection I1 I0 R1 8 R0 WCR/Pot Selection P1 P0 (LSB) © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice CAT5409 Registers is a non-volatile operation and will take a maximum of 5ms. WIPER CONTROL AND DATA REGISTERS Wiper Control Register (WCR) The CAT5409 contains four 6-bit Wiper Control Registers, one for each potentiometer. The Wiper Control Register output is decoded to select one of 64 switches along its resistor array. The contents of the WCR can be altered in four ways: it may be written by the host via Write Wiper Control Register instruction; it may be written by transferring the contents of one of four associated Data Registers via the XFR Data Register instruction, it can be modified one step at a time by the Increment/decrement instruction (see Instruction section for more details). Finally, it is loaded with the content of its data register zero (DR0) upon power-up. If the application does not require storage of multiple settings for the potentiometer, the Data Registers can be used as standard memory locations for system parameters or user preference data. INSTRUCTIONS Four of the nine instructions are three bytes in length. These instructions are: — Read Wiper Control Register – read the current wiper position of the selected potentiometer in the WCR — Write Wiper Control Register – change current wiper position in the WCR of the selected potentiometer — Read Data Register – read the contents of the selected Data Register — Write Data Register – write a new value to the selected Data Register The basic sequence of the three byte instructions is illustrated in Figure 8. These three-byte instructions exchange data between the WCR and one of the Data Registers. The WCR controls the position of the wiper. The response of the wiper to this action will be delayed by tWRL. A transfer from the WCR (current wiper The Wiper Control Register is a volatile register that loses its contents when the CAT5409 is powereddown. Although the register is automatically loaded with the value in DR0 upon power-up, this may be different from the value present at power-down. Data Registers (DR) Each potentiometer has four 6-bit non-volatile Data Registers. These can be read or written directly by the host. Data can also be transferred between any of the four Data Registers and the associated Wiper Control Register. Any data changes in one of the Data Table 3. Instruction Set Note: 1/0 = data is one or zero Instruction Set Instruction I3 1 I2 0 I1 0 I0 1 R1 0 R0 0 Write Wiper Control Register 1 0 1 0 0 Read Data Register 1 0 1 1 Write Data Register 1 1 0 XFR Data Register to Wiper Control Register 1 1 XFR Wiper Control Register to Data Register 1 Gang XFR Data Registers to Wiper Control Registers Gang XFR Wiper Control Registers to Data Register Read Wiper Control Register Increment/Decrement Wiper Control Register Operation WCR1/ P1 1/0 WCR0/ P0 1/0 0 1/0 1/0 Write new value to the Wiper Control Register pointed to by P1-P0 1/0 1/0 1/0 1/0 0 1/0 1/0 1/0 1/0 0 1 1/0 1/0 1/0 1/0 Read the contents of the Data Register pointed to by P1-P0 and R1-R0 Write new value to the Data Register pointed to by P1-P0 and R1-R0 Transfer the contents of the Data Register pointed to by P1-P0 and R1-R0 to its associated Wiper Control Register 1 1 0 1/0 1/0 1/0 1/0 Transfer the contents of the Wiper Control Register pointed to by P1-P0 to the Data Register pointed to by R1-R0 0 0 0 1 1/0 1/0 0 0 Transfer the contents of the Data Registers pointed to by R1-R0 of all four pots to their respective Wiper Control Registers 1 0 0 0 1/0 1/0 0 0 Transfer the contents of both Wiper Control Registers to their respective data Registers pointed to by R1-R0 of all four pots 0 0 1 0 0 0 1/0 1/0 © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice 9 Read the contents of the Wiper Control Register pointed to by P1-P0 Enable Increment/decrement of the Control Latch pointed to by P1-P0 Doc. No. MD-2010 Rev. M CAT5409 — Global XFR Data Register to Wiper Control Register This transfers the contents of all specified Data Registers to the associated Wiper Control Registers. — Global XFR Wiper Counter Register to Data Register This transfers the contents of all Wiper Control Registers to the specified associated Data Registers. position), to a Data Register is a write to non-volatile memory and takes a minimum of tWR to complete. The transfer can occur between one of the four potentiometers and one of its associated registers; or the transfer can occur between all potentiometers and one associated register. Four instructions require a two-byte sequence to complete, as illustrated in Figure 7. These instructions transfer data between the host/processor and the CAT5409; either between the host and one of the data registers or directly between the host and the Wiper Control Register. These instructions are: INCREMENT/DECREMENT COMMAND The final command is Increment/Decrement (Figure 5 and 9). The Increment/Decrement command is different from the other commands. Once the command is issued and the CAT5409 has responded with an acknowledge, the master can clock the selected wiper up and/or down in one segment steps; thereby providing a fine tuning capability to the host. For each SCL clock pulse (tHIGH) while SDA is HIGH, the selected wiper will move one resistor segment towards the RH terminal. Similarly, for each SCL clock pulse while SDA is LOW, the selected wiper will move one resistor segment towards the RL terminal. — XFR Data Register to Wiper Control Register This transfers the contents of one specified Data Register to the associated Wiper Control Register. — XFR Wiper Control Register to Data Register This transfers the contents of the specified Wiper Control Register to the specified associated Data Register. See Instructions format for more detail. Figure 7. Two-Byte Instruction Sequence SDA 0 1 0 1 S ID3 ID2 ID1 ID0 A3 T A R Device ID T A2 A1 A0 A I3 C K Internal Address I2 I1 I0 Instruction Opcode R1 R0 P1 P0 Register Address A C K Pot/WCR Address S T O P Figure 8. Three-Byte Instruction Sequence SDA 0 1 0 1 S ID3 ID2 ID1 ID0 A3 T A Device ID R T A2 A0 A I3 C K Internal Address A1 I2 I1 I0 R1 R0 P1 P0 A C K Data Pot/WCR Register Address Address Instruction Opcode D7 D6 D5 D4 D3 D2 D1 D0 WCR[7:0] or Data Register D[7:0] A C K S T O P Figure 9. Increment/Decrement Instruction Sequence 0 SDA S T A R T 1 0 1 ID3 ID2 ID1 ID0 Doc. No. MD-2010 Rev. M Device ID A3 A2 A1 A0 Internal Address A C K I3 I2 I1 Instruction Opcode 10 I0 R1 R0 P1 P0 A C Pot/WCR K Data Register Address Address I N C 1 I N C 2 I N C n D E C 1 D E C n S T O P © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice CAT5409 Figure 10. Increment/Decrement Timing Limits INC/DEC Command Issued tWRID SCL SDA Voltage Out RW INSTRUCTION FORMAT Read Wiper Control Register (WCR) S T A R T DEVICE ADDRESSES 0 1 0 1 A3 A2 A1 A0 A C K INSTRUCTION 1 0 0 1 0 0 P1 P0 A C K DATA 7 0 6 0 5 4 3 2 1 0 A C K S T O P A C K S T O P A C K S T O P A C K S T O P Write Wiper Control Register (WCR) S T A R T DEVICE ADDRESSES 0 1 0 1 A3 A2 A1 A0 A C K INSTRUCTION 1 0 1 0 0 0 P1 P0 A C K DATA 7 0 6 0 5 4 3 2 1 0 Read Data Register (DR) S T A R T DEVICE ADDRESSES 0 1 0 1 A3 A2 A1 A0 A C K INSTRUCTION 1 0 1 1 R1 R0 P1 P0 A C K DATA 7 0 6 0 5 4 3 2 1 0 Write Data Register (DR) S T A R T DEVICE ADDRESSES 0 1 0 1 A3 A2 © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice A1 A0 A C K INSTRUCTION 1 1 0 0 R1 11 R0 P1 P0 A C K DATA 7 0 6 0 5 4 3 2 1 0 Doc. No. MD-2010 Rev. M CAT5409 INSTRUCTION FORMAT (continued) Global Transfer Data Register (DR) to Wiper Control Register (WCR) S T A R T DEVICE ADDRESSES 0 1 0 1 A3 A2 A1 A0 A C K INSTRUCTION 0 0 0 1 R1 R0 0 0 A C K S T O P A C K S T O P A C K S T O P A C K S T O P Global Transfer Wiper Control Register (WCR) to Data Register (DR) S T A R T DEVICE ADDRESSES 0 1 0 1 A3 A2 A1 A0 A C K INSTRUCTION 1 0 0 0 R1 R0 0 0 Transfer Wiper Control Register (WCR) to Data Register (DR) S T A R T DEVICE ADDRESSES 0 1 0 1 A3 A2 A1 A0 A C K INSTRUCTION 1 1 1 0 R1 R0 P1 P0 Transfer Data Register (DR) to Wiper Control Register (WCR) S T A R T DEVICE ADDRESSES 0 1 0 1 A3 A2 A1 A0 A C K INSTRUCTION 1 1 0 1 R1 R0 P1 P0 Increment (I)/Decrement (D) Wiper Control Register (WCR) S T A R T DEVICE ADDRESSES 0 1 0 1 A3 A2 A1 A0 A C K INSTRUCTION 0 0 1 0 0 0 P1 P0 A C K DATA I/D I/D ... I/D I/D S T O P Note: (1) Any write or transfer to the Non-volatile Data Registers is followed by a high voltage cycle after a STOP has been issued. Doc. No. MD-2010 Rev. M 12 © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice CAT5409 PACKAGE OUTLINE DRAWINGS SOIC 24-Lead 300 mils (W) (1)(2) E1 SYMBOL MIN A 2.35 2.65 A1 0.10 0.30 A2 2.05 2.55 b 0.31 0.51 c 0.20 0.33 D 15.20 15.40 E 10.11 10.51 E1 7.34 E e b e PIN#1 IDENTIFICATION NOM MAX 7.60 1.27 BSC h 0.25 0.75 L 0.40 1.27 θ 0° 8° θ1 5° 15° TOP VIEW h D A2 A h θ1 θ θ1 L A1 SIDE VIEW c END VIEW Notes: (1) All dimensions in millimeters. Angle in degrees. (2) Compiles with JEDEC standard MS-013. © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice 13 Doc. No. MD-2010 Rev. M CAT5409 TSSOP 24-Lead 4.4 mm (Y) (1)(2) b SYMBOL MIN NOM A E1 E MAX 1.20 A1 0.05 0.15 A2 0.80 1.05 b 0.19 0.30 c 0.09 0.20 D 7.70 7.80 7.90 E 6.25 6.40 6.55 E1 4.30 4.40 4.50 e 0.65 BSC L 1.00 REF L1 0.50 θ1 0° 0.60 0.70 8° e TOP VIEW D c A2 A θ1 L1 A1 L SIDE VIEW END VIEW Notes: (1) All dimensions in millimeters. Angle in degrees. (2) Compiles with JEDEC standard MO-153. Doc. No. MD-2010 Rev. M 14 © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice CAT5409 EXAMPLE OF ORDERING INFORMATION (1) Prefix Device # CAT 5409 Company ID Suffix W I Package W: SOIC Y: TSSOP -00 Temperature Range I = Industrial (-40ºC to 85ºC) Resistance 25: 2.5 kΩ 10: 10 kΩ 50: 50 kΩ 00: 100 kΩ - T1 Tape & Reel T: Tape & Reel 1: 1,000/Reel – SOIC 2: 2,000/Reel – TSSOP Product Number 5409 ORDERING INFORMATION Orderable Part Number Resistance (kΩ) CAT5409WI-25-T1 2.5 CAT5409WI-10-T1 10 CAT5409WI-50-T1 50 CAT5409WI-00-T1 100 CAT5409YI-25-T2 2.5 CAT5409YI-10-T2 10 CAT5409YI-50-T2 50 CAT5409YI-00-T2 100 CAT5409WI25 2.5 CAT5409WI10 10 CAT5409WI50 50 CAT5409WI00 100 CAT5409YI25 2.5 CAT5409YI10 10 CAT5409YI50 50 CAT5409YI00 100 Package Lead Finish SOIC TSSOP Matte-Tin SOIC TSSOP Notes: (1) All packages are RoHS-compliant (Lead-free, Halogen-free). (2) The device used in the above example is a CAT5409WI-00-T1 (SOIC, Industrial Temperature, 100 kΩ, Tape & Reel, 1,000/Reel). (3) For additional package and temperature options, please contact your nearest ON Semiconductor Sales office. © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice 15 Doc. No. MD-2010 Rev. M CAT5409 REVISION HISTORY Date Rev. 08-Oct-03 H Description Updated Features Updated Description I Changed Preliminary designation to Final Eliminated Commercial temp range in all areas Updated ¯¯¯ WP Pin Description Updated notes in Absolute Max Ratings and Potentiometer Characteristics 02-May-08 J Deleted BGA package Updated Potentiometer Characteristics table Update Package Outline Drawings Updated Example of Ordering Information Added MD- to document number 07-Apr-08 K Change 2-wire with I²C Update Ordering Part Number table 26-Nov-08 L Change logo and fine print to ON Semiconductor 31-Jul-09 M Update Ordering Information table 29-Apr-06 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: [email protected] Doc. No. MD-2010 Rev. M N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center: Phone: 81-3-5773-3850 16 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice