MCP6V91/1U/2/4 10 MHz, Zero-Drift Op Amps Features General Description • High DC Precision: - VOS Drift: ±17 nV/°C (maximum, VDD = 5.5V) - VOS: ±9 µV (maximum) - AOL: 126 dB (minimum, VDD = 5.5V) - PSRR: 117 dB (minimum, VDD = 5.5V) - CMRR: 118 dB (minimum, VDD = 5.5V) - Eni: 0.24 µVP-P (typical), f = 0.1 Hz to 10 Hz - Eni: 0.08 µVP-P (typical), f = 0.01 Hz to 1 Hz • Enhanced EMI Protection: - Electromagnetic Interference Rejection Ratio (EMIRR) at 1.8 GHz: 93 dB • Low Power and Supply Voltages: - IQ: 1.1 mA/amplifier (typical) - Wide supply voltage range: 2.4V to 5.5V • Small Packages: - Singles in SC70, SOT-23 - Duals in MSOP-8, 2X3 TDFN - Quads in TSSOP-14 • Easy to Use: - Rail-to-rail input/output - Gain Bandwidth Product: 10 MHz (typical) - Unity Gain Stable • Extended Temperature Range: -40°C to +125°C The Microchip Technology Incorporated MCP6V91/1U/2/4 family of operational amplifiers provides input offset voltage correction for very low offset and offset drift. These devices have a gain bandwidth product of 10 MHz (typical). They are unity-gain stable, have virtually no 1/f noise and have good Power Supply Rejection Ratio (PSRR) and Common Mode Rejection Ratio (CMRR). These products operate with a single supply voltage as low as 2.4V, while drawing 1.1 mA/amplifier (typical) of quiescent current. The MCP6V91/1U/2/4 family has enhanced EMI protection to minimize any electromagnetic interference from external sources. This feature makes it well suited for EMI-sensitive applications such as power lines, radio stations and mobile communications, etc. The MCP6V91/1U/2/4 op amps are offered in single (MCP6V91 and MCP6V91U), dual (MCP6V92) and quad (MCP6V94) packages. They were designed using an advanced CMOS process. Typical Applications • • • • • Portable Instrumentation Sensor Conditioning Temperature Measurement DC Offset Correction Medical Instrumentation Design Aids • • • • • SPICE Macro Models FilterLab® Software Microchip Advanced Part Selector (MAPS) Analog Demonstration and Evaluation Boards Application Notes Related Parts • • • • • MCP6V11/1U/2/4: Zero-Drift, Low Power MCP6V31/1U/2/4: Zero-Drift, Low Power MCP6V61/1U/2/4: Zero-Drift, 1 MHz MCP6V71/1U/2/4: Zero-Drift, 2 MHz MCP6V81/1U/2/4: Zero-Drift, 5 MHz 2015-2016 Microchip Technology Inc. Package Types MCP6V91 SOT-23 VOUT 1 VSS 2 VIN+ 3 MCP6V91U SC70, SOT-23 5 VDD VIN+ 1 4 VIN– VSS 2 VIN– 3 MCP6V92 MSOP VOUTA VINA– VINA+ VSS 1 2 3 4 8 7 6 5 5 VDD 4 VOUT MCP6V92 2×3 TDFN* VDD VOUTA 1 VOUTB VINA- 2 VINB- VINA+ 3 VSS 4 VINB+ 8 VDD EP 9 7 VOUTB 6 VINB5 VINB+ MCP6V94 TSSOP VOUTA VINAVINA+ VDD VINB+ VINBVOUTB 1 2 3 4 5 6 7 14 VOUTD 13 VIND12 VIND+ 11 VSS 10 VINC+ 9 VINC8 VOUTC * Includes Exposed Thermal Pad (EP); see Table 3-1. DS20005434B-page 1 MCP6V91/1U/2/4 Typical Application Circuit R1 R3 R2 R2 VDD/2 R4 C2 + R5 U2 VOUT - 8 + 6 U1 MCP6XXX VDD/2 MCP6V91 Offset Voltage Correction for Power Driver Input Offset Voltage (µV) VIN Figures 1 and 2 show input offset voltage of the singlechannel device MCP6V91 versus ambient temperature for different power supply voltages. 26 Samples VDD = 2.4V 4 2 0 -2 -4 -6 -8 -50 -25 0 25 50 75 Ambient Temperature (°C) 100 125 FIGURE 1: Input Offset Voltage vs. Ambient Temperature with VDD = 2.4V. Input Offset Voltage (µV) 8 6 26 Samples VDD = 5.5V 4 2 0 -2 -4 -6 -8 -50 -25 0 25 50 75 100 Ambient Temperature (°C) 125 FIGURE 2: Input Offset Voltage vs. Ambient Temperature with VDD = 5.5V. As seen in Figures 1 and 2, the MCP6V91/1U op amps have excellent performance across temperature. The input offset voltage temperature drift (TC1) shown is well within the specified maximum values of 17 nV/°C at VDD = 5.5V and 24 nV/°C at VDD = 2.4V. This performance supports applications with stringent DC precision requirements. In many cases, it will not be necessary to correct for temperature effects (i.e., calibrate) in a design. In the other cases, the correction will be small. DS20005434B-page 2 2015-2016 Microchip Technology Inc. MCP6V91/1U/2/4 1.0 ELECTRICAL CHARACTERISTICS 1.1 Absolute Maximum Ratings † VDD – VSS .................................................................................................................................................................6.5V Current at Input Pins ..............................................................................................................................................±2 mA Analog Inputs (VIN+ and VIN–)(1)...............................................................................................VSS – 1.0V to VDD + 1.0V All Other Inputs and Outputs ....................................................................................................VSS – 0.3V to VDD + 0.3V Difference Input Voltage .................................................................................................................................|VDD – VSS| Output Short Circuit Current ........................................................................................................................... Continuous Current at Output and Supply Pins ...................................................................................................................... ±30 mA Storage Temperature .............................................................................................................................-65°C to +150°C Maximum Junction Temperature .......................................................................................................................... +150°C ESD protection on all pins (HBM, CDM, MM) MCP6V91/1U 4 kV, 1.5 kV, 400V MCP6V92/4 4 kV, 1.5 kV, 300V † Notice: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. Note 1: See Section 4.2.1 “Rail-to-Rail Inputs”. 1.2 Specifications TABLE 1-1: DC ELECTRICAL SPECIFICATIONS Electrical Characteristics: Unless otherwise indicated, TA = +25°C, VDD = +2.4V to +5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 10 kΩ to VL and CL = 30 pF (refer to Figures 1-4 and 1-5). Parameters Sym. Min. Typ. Max. Units Conditions Input Offset Input Offset Voltage VOS -9 — +9 µV TC1 -24 — +24 nV/°C TA = -40 to +125°C, VDD = 2.4V (Note 1) TC1 -17 — +17 nV/°C TA = -40 to +125°C, VDD = 5.5V (Note 1) Input Offset Voltage Drift with Temperature (Linear Temperature Coefficient) MCP6V92/4 TC1 -30 — +30 nV/°C TA = -40 to +125°C, (Note 1) Input Offset Voltage Quadratic Temperature Coefficient MCP6V91/1U TC2 — ±30 — pV/°C2 TA = -40 to +125°C VDD = 2.4V TC2 — ±12 — pV/°C2 TA = -40 to +125°C VDD = 5.5V TC2 — ±74 — pV/°C2 TA = -40 to +125°C VDD = 2.4V TC2 — ±48 — pV/°C2 TA = -40 to +125°C VDD = 5.5V Input Offset Voltage Drift with Temperature (Linear Temperature Coefficient) MCP6V91/1U Input Offset Voltage Quadratic Temperature Coefficient MCP6V92/4 Note 1: 2: TA = +25°C For design guidance only; not tested. Figure 2-19 shows how VCML and VCMH changed across temperature for the first production lot. 2015-2016 Microchip Technology Inc. DS20005434B-page 3 MCP6V91/1U/2/4 TABLE 1-1: DC ELECTRICAL SPECIFICATIONS (CONTINUED) Electrical Characteristics: Unless otherwise indicated, TA = +25°C, VDD = +2.4V to +5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 10 kΩ to VL and CL = 30 pF (refer to Figures 1-4 and 1-5). Parameters Sym. Min. Typ. Max. Units Conditions Input Offset Voltage Aging ∆VOS — ±0.75 — µV 408 hours Life Test at +150°, measured at +25°C. Power Supply Rejection Ratio PSRR 117 137 — dB Input Bias Current IB -50 ±2 +50 pA Input Bias Current across Temperature IB — +10 — pA TA = +85°C TA = +125°C Input Bias Current and Impedance IB 0 +0.2 +1 nA Input Offset Current IOS -400 ±100 +400 pA Input Offset Current across Temperature IOS — ±75 — pA TA = +85°C IOS -500 ±100 +500 pA TA = +125°C Common-Mode Input Impedance ZCM — 1013||14 — Ω||pF Differential Input Impedance ZDIFF — 1013||3 — Ω||pF Common-Mode Input Voltage Range Low VCML — — VSS–0.2 V Note 2 Common-Mode Input Voltage Range High VCMH VDD+0.3 — — V Note 2 Common-Mode Rejection Ratio CMRR 112 132 — dB VDD = 2.4V, VCM = -0.2V to 2.7V (Note 2) CMRR 118 140 — dB VDD = 5.5V, VCM = -0.2V to 5.8V (Note 2) AOL 119 142 — dB VDD = 2.4V, VOUT = 0.3V to 2.0V AOL 126 158 — dB VDD = 5.5V, VOUT = 0.3V to 5.3V VOL VSS VSS+35 VSS+120 mV RL = 1 kΩ, G = +2, 0.5V input overdrive VOL — VSS+7 — mV RL = 10 kΩ, G = +2, 0.5V input overdrive VOH VDD–120 VDD–45 VDD mV RL = 1 kΩ, G = +2, 0.5V input overdrive VOH — VDD–9 — mV RL = 10 kΩ, G = +2, 0.5V input overdrive ISC — ±15 — mA VDD = 2.4V ISC — ±40 — mA VDD = 5.5V VDD 2.4 — 5.5 V IQ 0.6 1.1 1.6 mA VPOR 1.4 1.85 2.2 V Common Mode Open-Loop Gain DC Open-Loop Gain (Large Signal) Output Minimum Output Voltage Swing Maximum Output Voltage Swing Output Short-Circuit Current Power Supply Supply Voltage Quiescent Current per Amplifier Power-on Reset (POR) Trip Voltage Note 1: 2: IO = 0 For design guidance only; not tested. Figure 2-19 shows how VCML and VCMH changed across temperature for the first production lot. DS20005434B-page 4 2015-2016 Microchip Technology Inc. MCP6V91/1U/2/4 TABLE 1-2: AC ELECTRICAL SPECIFICATIONS Electrical Characteristics: Unless otherwise indicated, TA = +25°C, VDD = +2.4V to +5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 10 kΩ to VL and CL = 30 pF (refer to Figures 1-4 and 1-5). Parameters Sym. Min. Typ. Max. Units GBWP — 10 — MHz Conditions Amplifier AC Response Gain Bandwidth Product Slew Rate SR — 9.5 — V/µs Phase Margin PM — 60 — °C Eni — 0.08 — µVP-P f = 0.01 Hz to 1 Hz µVP-P f = 0.1 Hz to 10 Hz G = +1 Amplifier Noise Response Input Noise Voltage Eni — 0.24 — Input Noise Voltage Density eni — 11 — nV/√Hz f < 2 kHz, VDD = 5.5V Input Noise Current Density ini — 6 — fA/√Hz IMD — 35 — µVPK Start-Up Time tSTR — 100 — µs G = +1, 0.1% VOUT settling (Note 2) Offset Correction Settling Time tSTL — 60 — µs G = +1, VIN step of 2V, VOS within 100 µV of its final value Output Overdrive Recovery Time tODR — 65 — µs G = -10, ±0.5V input overdrive to VDD/2, VIN 50% point to VOUT 90% point (Note 3) EMIRR — 88 — dB VIN = 0.1 VPK, f = 400 MHz — 95 — VIN = 0.1 VPK, f = 900 MHz — 93 — VIN = 0.1 VPK, f = 1800 MHz — 90 — VIN = 0.1 VPK, f = 2400 MHz Amplifier Distortion(1) Intermodulation Distortion (AC) VCM tone = 100 mVPK at 1 kHz, GN = 11, RTI Amplifier Step Response EMI Protection EMI Rejection Ratio Note 1: 2: 3: These parameters were characterized using the circuit in Figure 1-6. In Figures 2-40 and 2-41, there is an IMD tone at DC, a residual tone at 1 kHz and other IMD tones and clock tones. IMD is Referred to Input (RTI). High gains behave differently; see Section 4.3.3 “Offset at Power-Up”. tSTL and tODR include some uncertainty due to clock edge timing. TABLE 1-3: TEMPERATURE SPECIFICATIONS Electrical Characteristics: Unless otherwise indicated, all limits are specified for: VDD = +2.4V to +5.5V, VSS = GND. Parameters Sym. Min. Typ. Max. Units Specified Temperature Range TA -40 — +125 °C Operating Temperature Range TA -40 — +125 °C Storage Temperature Range TA -65 — +150 °C Thermal Resistance, 5LD-SC70 JA — 209 — °C/W Thermal Resistance, 5LD-SOT-23 JA — 201 — °C/W Thermal Resistance, 8L-2x3 TDFN JA — 53 — °C/W Thermal Resistance, 8L-MSOP JA — 211 — °C/W Thermal Resistance, 14L-TSSOP JA — 100 — °C/W Conditions Temperature Ranges Note 1 Thermal Package Resistances Note 1: Operation must not cause TJ to exceed Maximum Junction Temperature specification (+150°C). 2015-2016 Microchip Technology Inc. DS20005434B-page 5 MCP6V91/1U/2/4 1.3 Timing Diagrams 1.4 2.4V to 5.5V 2.4V VDD 0V tSTR 1.001(VDD/3) VOUT Test Circuits The circuits used for most DC and AC tests are shown in Figures 1-4 and 1-5. Lay the bypass capacitors out as discussed in Section 4.3.10 “Supply Bypassing and Filtering”. RN is equal to the parallel combination of RF and RG to minimize bias current effects. 0.999(VDD/3) FIGURE 1-1: Amplifier Start-Up. VDD VIN 100 nF VDD/3 tSTL VOS + 100 µV RG VOS VOS – 100 µV FIGURE 1-2: Time. Offset Correction Settling 100 nF RG tODR VDD/2 VSS FIGURE 1-3: RISO VIN VDD Output Overdrive Recovery. VL 1 µF + MCP6V9X tODR RL FIGURE 1-4: AC and DC Test Circuit for Most Noninverting Gain Conditions. VDD VIN CL VOUT RF VDD/3 RN VOUT RISO + MCP6V9X VIN 1 µF RN CL VOUT RL VL RF FIGURE 1-5: AC and DC Test Circuit for Most Inverting Gain Conditions. The circuit in Figure 1-6 tests the input’s dynamic behavior (i.e., IMD, tSTR, tSTL and tODR). The potentiometer balances the resistor network (VOUT should equal VREF at DC). The op amp’s common-mode input voltage is VCM = VIN/2. The error at the input (VERR) appears at VOUT with a noise gain of 10 V/V. 11.0 kΩ 100 kΩ 500Ω 0.1% 0.1% 25 turn VREF = VDD/3 VDD 1 µF VIN 100 nF MCP6V9X 11.0 kΩ 100 kΩ 249Ω 1% 0.1% 0.1% FIGURE 1-6: Input Behavior. DS20005434B-page 6 RISO 0Ω VOUT CL 30 pF RL open VL Test Circuit for Dynamic 2015-2016 Microchip Technology Inc. MCP6V91/1U/2/4 2.0 TYPICAL PERFORMANCE CURVES Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. Note: Unless otherwise indicated, TA = +25°C, VDD = +2.4V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 10 kΩ to VL and CL = 30 pF. 2.1 DC Input Precision 25% 8 26 Samples TA = +25°C MCP6V91 20% VDD = 2.4V VDD = 5.5V 15% 4 2 0 -2 10% -4 5% -8 -5 -4 -3 FIGURE 2-1: -2 -1 0 1 2 3 Input Offset Voltage (µV) 4 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 Power Supply Voltage (V) 5 Input Offset Voltage. FIGURE 2-4: Input Offset Voltage vs. Power Supply Voltage with VCM = VCML. 8 26 Samples TA = -40°C to +125°C MCP6V91 VDD = 2.4V VDD = 5.5V 20% 15% Representative Part VCM = VDD – 0.1V 6 Input Offset Voltage (µV) Percentage of Occurrences 30% 25% TA = -40°C TA = +25°C TA = +85°C TA = +125°C -6 0% 4 2 0 -2 10% -4 5% -8 -10 -8 -6 -4 -2 0 2 4 6 8 Input Offset Voltage Drift; TC1 (nV/°C) FIGURE 2-2: 10 Input Offset Voltage Drift. 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 Power Supply Voltage (V) FIGURE 2-5: Input Offset Voltage vs. Power Supply Voltage with VCM = VCMH. 35% 25% 20% 26 Samples TA = -40°C to +125°C MCP6V91 VDD = 5.5V VDD = 2.4V 15% 8 Input Offset Voltage (µV) 30% TA = -40°C TA = +25°C TA = +85°C TA = +125°C -6 0% Percentage of Occurrences Representative Part VCM = 0.1V 6 Input Offset Voltage (µV) Percentage of Occurrences 30% Representative Part VDD = 2.4V 6 4 2 0 -2 10% -4 5% -6 0% -100 -80 -60 -40 -20 0 20 40 60 80 100 Input Offset Voltage's Quadratic Temp Co; TC2 (pV/°C2) FIGURE 2-3: Input Offset Voltage Quadratic Temperature Coefficient. 2015-2016 Microchip Technology Inc. -8 TA = -40°C TA = +25°C TA = +85°C TA = +125°C 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 Output Voltage (V) FIGURE 2-6: Input Offset Voltage vs. Output Voltage with VDD = 2.4V. DS20005434B-page 7 MCP6V91/1U/2/4 Note: Unless otherwise indicated, TA = +25°C, VDD = +2.4V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 10 kΩ to VL and CL = 30 pF. Representative Part VDD = 5.5V 6 Percentage of Occurrences Input Offset Voltage (µV) 8 4 2 0 -2 -4 TA = -40°C TA = +25°C TA = +85°C TA = +125°C -6 -8 60% 50% Tester Data 599 Samples TA = +25ºC 30% VDD = 2.4V 20% 10% 0% -1.6 -1.2 -0.8 -0.4 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 Output Voltage (V) FIGURE 2-7: Input Offset Voltage vs. Output Voltage with VDD = 5.5V. FIGURE 2-10: Ratio. 4 2 0 -2 -4 TA = -40°C TA = +25°C TA = +85°C TA = +125°C -6 -8 -0.5 0.0 Percentage of Occurrences Input Offset Voltage (µV) Representative Part VDD = 2.4V TA = +85°C TA = +125°C 0 -2 TA = -40°C TA = +25°C -8 -0.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 Common Mode Input Voltage (V) FIGURE 2-9: Input Offset Voltage vs. Common-Mode Voltage with VDD = 5.5V. DS20005434B-page 8 1.6 50% Tester Data 599 Samples TA = +25ºC 40% 30% 20% 10% 0 0.2 0.4 0.6 0.8 1 1/PSRR (µV/V) FIGURE 2-11: Ratio. Power Supply Rejection 80% Percentage of Occurrences Input Offset Voltage (µV) Representative Part VDD = 5.5V 4 -6 1.2 60% -1 -0.8 -0.6 -0.4 -0.2 8 -4 0.8 Common-Mode Rejection 3.0 FIGURE 2-8: Input Offset Voltage vs. Common-Mode Voltage with VDD = 2.4V. 2 0.4 0% 0.5 1.0 1.5 2.0 2.5 Common Mode Input Voltage (V) 6 0 1/CMRR (µV/V) 8 6 VDD = 5.5V 40% 70% 60% Tester Data 599 Samples TA = +25ºC VDD = 5.5V 50% 40% 30% VDD = 2.4V 20% 10% 0% -0.5 -0.4 -0.3 -0.2 -0.1 0 0.1 0.2 0.3 0.4 0.5 1/AOL (µV/V) FIGURE 2-12: DC Open-Loop Gain. 2015-2016 Microchip Technology Inc. MCP6V91/1U/2/4 Input Current Magnitude (A) 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 Input Offset Current 0.5 6.0 5.5 5.0 4.5 4.0 3.5 3.0 125 1m Input Bias Current 0.0 2.5 FIGURE 2-17: Input Bias and Offset Currents vs. Ambient Temperature with VDD = 5.5V. VDD = 5.5 V TA = +85 ºC -0.5 2.0 Ambient Temperature (°C) FIGURE 2-14: DC Open-Loop Gain vs. Ambient Temperature. 500 400 300 200 100 0 -100 -200 -300 -400 -500 0.1p 125 115 100 105 0 25 50 75 Ambient Temperature (°C) Input Bias Current 1p 95 -25 10p Input Offset Current 85 Typical Gains 100p 75 VDD = 2.4V VDD = 5.5V VDD = 5.5 V 65 Input Bias, Offset Currents (A) DC Open-Loop Gain (dB) 1n -50 Input Bias and Offset Currents (pA) Input Common Mode Voltage (V) FIGURE 2-16: Input Bias and Offset Currents vs. Common-Mode Input Voltage with TA = +125°C. FIGURE 2-13: CMRR and PSRR vs. Ambient Temperature. 160 155 150 145 140 135 130 125 120 115 110 105 100 1.5 125 1.0 100 55 0 25 50 75 Ambient Temperature (°C) 45 -25 35 -50 Input Bias Current Input Offset Current 0.5 CMRR at VDD = 5.5V CMRR at VDD = 2.4V VDD = 5.5 V TA = +125 ºC 0.0 PSRR 500 400 300 200 100 0 -100 -200 -300 -400 -500 -0.5 Typical Gains 25 160 155 150 145 140 135 130 125 120 115 110 105 100 Input Bias and Offset Currents (pA) CMRR, PSRR (dB) Note: Unless otherwise indicated, TA = +25°C, VDD = +2.4V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 10 kΩ to VL and CL = 30 pF. Input Common Mode Voltage (V) FIGURE 2-15: Input Bias and Offset Currents vs. Common-Mode Input Voltage with TA = +85°C. 2015-2016 Microchip Technology Inc. 100µ 10µ 1µ 100n 10n 1n TA = +125°C TA = +85°C TA = +25°C TA = - 40°C 100p 10p -1.0 -0.9 -0.8 -0.7 -0.6 -0.5 -0.4 -0.3 -0.2 -0.1 0.0 Input Voltage (V) FIGURE 2-18: Input Bias Current vs. Input Voltage (Below VSS). DS20005434B-page 9 MCP6V91/1U/2/4 Note: Unless otherwise indicated, TA = +25°C, VDD = +2.4V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 10 kΩ to VL and CL = 30 pF. Other DC Voltages and Currents 80 1 Wafer Lot 0.4 Upper (VCMH – VDD) 0.3 0.2 0.1 VDD = 2.4V VDD = 5.5V 0.0 -0.1 -0.2 -0.3 -0.4 Lower (VCML – VSS) -0.5 -50 -25 0 -20 TA = +125°C TA = +85°C TA = +25°C TA = -40°C -40 -60 0.5 1 1.5 2 2.5 3 3.5 4 4.5 Power Supply Voltage (V) 5 5.5 6 FIGURE 2-22: Output Short-Circuit Current vs. Power Supply Voltage. 1600 1400 VDD = 2.4V Quiescent Current (µA/Amplifier) 100 VDD -VOH VDD = 5.5V 10 1200 1000 800 TA = +125°C TA = +85°C TA = +25°C TA = -40°C 600 400 200 VOL -VSS 0 1 20 VDD = 2.4V 10 VOL - VSS 0 -50 -25 0 25 50 75 Ambient Temperature (°C) 100 125 FIGURE 2-21: Output Voltage Headroom vs. Ambient Temperature. DS20005434B-page 10 2.1 30 2.05 40 2 VDD = 5.5V 430 Samples 1 Wafer Lot TA = +25ºC 1.95 VDD - VOH 50 100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 0% 1.9 70 Supply Current vs. Power 1.85 Percentage of Occurrences RL = 1 kȍ FIGURE 2-23: Supply Voltage. 1.8 FIGURE 2-20: Output Voltage Headroom vs. Output Current. 60 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 Power Supply Voltage (V) 10 1.75 1 Output Current Magnitude (mA) 1.7 0.1 1.6 Output Voltage Headroom (mV) 20 125 1000 Output Voltage Headroom (mV) 40 -80 0 25 50 75 100 Ambient Temperature (°C) FIGURE 2-19: Input Common-Mode Voltage Headroom (Range) vs. Ambient Temperature. 80 TA = +125°C TA = +85°C TA = +25°C TA = -40°C 60 1.65 Common-Mode Input Voltage Headroom (V) 0.5 Output Short Circuit Current (mA) 2.2 POR Trip Voltage (V) FIGURE 2-24: Voltage. Power-On Reset Trip 2015-2016 Microchip Technology Inc. MCP6V91/1U/2/4 Note: Unless otherwise indicated, TA = +25°C, VDD = +2.4V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 10 kΩ to VL and CL = 30 pF. 2.2 POR Trip Voltage (V) 2.1 2 1.9 1.8 1.7 1.6 1.5 1.4 -50 -25 0 25 50 75 Ambient Temperature (°C) 100 125 FIGURE 2-25: Power-On Reset Voltage vs. Ambient Temperature. 2015-2016 Microchip Technology Inc. DS20005434B-page 11 MCP6V91/1U/2/4 Note: Unless otherwise indicated, TA = +25°C, VDD = +2.4V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 10 kΩ to VL and CL = 30 pF. Frequency Response Representative Part PSRR+ 100 80 CMRR PSRR- 60 40 20 0 100 1k 10k 100k Frequency (Hz) FIGURE 2-26: Frequency. 1M 60 20 -150 Open-Loop Gain 10 -180 0 -210 -240 VDD = 2.4V CL = 30 pF -20 1.E+04 10k -270 100k 1.E+05 1.E+06 1M f (Hz) -90 -120 30 -150 20 Open-Loop Gain 10 -180 0 -210 -240 VDD = 5.5V CL = 30 pF -270 1.E+06 1M f (Hz) 1.E+07 10M FIGURE 2-28: Open-Loop Gain vs. Frequency with VDD = 5.5V. DS20005434B-page 12 GBWP 8 30 VDD = 2.4V 20 7 10 6 -25 0 25 50 75 100 Ambient Temperature (°C) 125 90 GBWP 10 80 8 70 6 60 4 50 PM VDD = 5.5V VDD = 2.4V 2 40 0 30 0 1 2 3 4 5 6 14 Open-Loop Phase (°) Open-Loop Gain (dB) Open-Loop Phase 1.E+05 100k 40 9 FIGURE 2-30: Gain Bandwidth Product and Phase Margin vs. Common-Mode Input Voltage. -60 50 -20 1.E+04 10k 50 Common Mode Input Voltage (V) -30 60 -10 10 -1 FIGURE 2-27: Open-Loop Gain vs. Frequency with VDD = 2.4V. 40 60 10M 1.E+07 Gain Bandwidth Product (MHz) -10 Gain Bandwidth Product (MHz) -120 Open-Loop Phase (°) Open-Loop Gain (dB) -90 30 11 12 -60 Open-Loop Phase 40 70 PM FIGURE 2-29: Gain Bandwidth Product and Phase Margin vs. Ambient Temperature. -30 50 12 -50 10M CMRR and PSRR vs. VDD = 5.5V Phase Margin (º) CMRR, PSRR (dB) 120 80 13 Phase Margin (°) Gain Bandwidth Product (MHz) 140 90 GBWP 12 80 PM 10 70 8 60 VDD = 5.5V 6 50 VDD = 2.4V 4 Phase Margin (º) 2.3 40 2 30 0 1 2 3 4 5 6 Output Voltage (V) FIGURE 2-31: Gain Bandwidth Product and Phase Margin vs. Output Voltage. 2015-2016 Microchip Technology Inc. MCP6V91/1U/2/4 Note: Unless otherwise indicated, TA = +25°C, VDD = +2.4V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 10 kΩ to VL and CL = 30 pF. 1000 100 10 GN : 101 V/V 11 V/V 1 V/V 1 EMIRR (dB) Closed Loop Output Impedance (Ω) VDD = 2.4V 0.1 1k 10k 100k 1M 10M 120 110 100 90 80 70 60 50 40 30 20 10 10 10M VPK = 100 mV VDD = 5.5V 100 100M Frequency (Hz) 1000 1G 10000 10G Frequency (Hz) FIGURE 2-35: FIGURE 2-32: Closed-Loop Output Impedance vs. Frequency with VDD = 2.2V. EMIRR vs. Frequency. 120 1000 VDD = 5.5V VDD = 5.5V 80 EMIRR (dB) Closed Loop Output Impedance (Ω) 100 100 GN : 101 V/V 11 V/V 1 V/V 10 60 40 EMIRR at 2400 MHz EMIRR at 1800 MHz EMIRR at 900 MHz EMIRR at 400 MHz 1 20 0.1 1.0E+03 1.0E+04 1k 10k 1.0E+05 100k 1.0E+06 0 0.01 1.0E+07 1M 10M Frequency (Hz) FIGURE 2-33: Closed-Loop Output Impedance vs. Frequency with VDD = 5.5V. VDD = 5.5V VDD = 2.4V 1 0.1 100k FIGURE 2-36: Channel-to-Channel Separation RTI (dB) Output Voltage Swing (VP-P) 10 10k 1M 10M Frequency (Hz) 100M FIGURE 2-34: Maximum Output Voltage Swing vs. Frequency. 2015-2016 Microchip Technology Inc. 0.10 1.00 10.00 RF Input Peak Voltage (Vp) EMIRR vs. Input Voltage. 150 140 130 VDD = 5.5V 120 110 VDD = 2.4V 100 90 80 1.E+03 1k 10k 100k 1.E+04 1.E+05 Frequency (Hz) 1M 1.E+06 FIGURE 2-37: Channel-to Channel Separation vs. Frequency. DS20005434B-page 13 MCP6V91/1U/2/4 Note: Unless otherwise indicated, TA = +25°C, VDD = +2.4V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 10 kΩ to VL and CL = 30 pF. Input Noise and Distortion 1000 VDD = 5.5V, red VDD = 2.4V, blue 100 100 eni 10 10 Eni (0 Hz to f) 1.E+3 1m G = 11 V/V VDD tone = 100 mVPK, f = 1 kHz IMD Spectrum, RTI (VPK) Input Noise Voltage Density; eni (nV/¥Hz) 1000 Integrated Input Noise Voltage; Eni (µVP-P) 2.4 1.E+2 100μ DC tone FIGURE 2-38: Input Noise Voltage Density and Integrated Input Noise Voltage vs. Frequency. Residual 1 kHz tone 1.E+1 10μ 1.E+0 1μ 1.E-1 100n ǻf = 64 Hz ǻf = 2 Hz 10n 1.E-2 1 1.E+0 1 1 1 10 100 1.E+3 1k 10k 1.E+5 100k 1.E+0 1.E+1 1.E+2 1.E+4 Frequency (Hz) VDD = 2.4V VDD = 5.5V 10 1.E+1 100 1k 1.E+2 1.E+3 Frequency (Hz) 10k 1.E+4 100k 1.E+5 FIGURE 2-41: Intermodulation Distortion vs. Frequency with VDD Disturbance (see Figure 1-6). VDD = 2.4V f < 2 kHz 25 20 VDD = 2.4V 15 NPBW = 10 Hz Input Noise Voltage; eni(t) (0.1 µV/div) Input Noise Voltage Density (nV/¥Hz) 30 10 VDD = 5.5V 5 0 -0.5 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 NPBW = 1 Hz 0 10 20 30 Common Mode Input Voltage (V) VDD = 2.4V VDD = 5.5V 1.E+2 100μ DC tone Residual 1 kHz tone (due to resistor mismatch) 1.E+1 10μ 1.E+0 1μ 100n 1.E-1 60 70 80 90 100 FIGURE 2-42: Input Noise vs. Time with 1 Hz and 10 Hz Filters and VDD = 2.4V. VDD = 5.5V Input Noise Voltage; eni(t) (0.1 µV/div) IMD Spectrum, RTI (VPK) G = 11 V/V VCM tone = 100 mVPK, f = 1 kHz 50 Time (s) FIGURE 2-39: Input Noise Voltage Density vs. Input Common-Mode Voltage. 1.E+3 1m 40 NPBW = 10 Hz NPBW = 1 Hz ǻf = 64 Hz ǻf = 2 Hz 0 10n 1.E-2 1 10 100 1k 100 1000 Frequency (Hz) 10k 10000 100k 100000 FIGURE 2-40: Intermodulation Distortion vs. Frequency with VCM Disturbance (see Figure 1-6). DS20005434B-page 14 10 20 30 40 50 60 70 80 90 100 Time (s) FIGURE 2-43: Input Noise vs. Time with 1 Hz and 10 Hz Filters and VDD = 5.5V. 2015-2016 Microchip Technology Inc. MCP6V91/1U/2/4 Note: Unless otherwise indicated, TA = +25°C, VDD = +2.4V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 10 kΩ to VL and CL = 30 pF. Input Offset Voltage (µV) 45 40 35 30 25 20 15 10 5 0 -5 -10 100 80 60 40 20 0 -20 -40 -60 -80 -100 -120 TPCB VDD = 5.5V VDD = 2.4V VOS Temperature is increased using a heat gun for 5 seconds Output Voltage (20mV/div) Time Response PCB Temperature (ºC) 2.5 VIN VOUT VDD = 5.5V G = +1 V/V 0 10 20 30 40 50 60 70 80 90 100 110 120 0 0.5 1 1.5 2 Time (s) FIGURE 2-47: Step Response. FIGURE 2-44: Input Offset Voltage vs. Time with Temperature Change. 6 5 5 VDD 4 20 VDD = 5.5V G = +1 V/V 15 10 3 2 POR Trip Point 1 5 VOS 0 0 -5 -1 0 1 2 3 4 5 6 7 8 9 Output Voltage (V) 25 6 Power Supply Voltage (V) Input Offset Voltage (mV) 30 2.5 3 3.5 Time (µs) 4 4.5 5 Noninverting Small Signal VOUT 4 VIN 3 VDD = 5.5 V G = +1 V/V 2 1 0 0 0.5 1 1.5 2 Time (µs) 10 2.5 3 3.5 4 Time (ms) FIGURE 2-45: Input Offset Voltage vs. Time at Power-Up. FIGURE 2-48: Step Response. Noninverting Large Signal VDD = 5.5 V G = +1 V/V 5 4 3 2 VOUT 1 0 VIN -1 Output Voltage (20 mV/div) Input, Output Voltages (V) 6 VIN VDD = 5.5 V G = -1 V/V VOUT 0 0.5 Time (1 µs/div) FIGURE 2-46: The MCP6V91/1U/2/4 Family Shows No Input Phase Reversal with Overdrive. 2015-2016 Microchip Technology Inc. 1 1.5 2 2.5 3 3.5 4 4.5 5 Time (µs) FIGURE 2-49: Response. Inverting Small Signal Step DS20005434B-page 15 MCP6V91/1U/2/4 Note: Unless otherwise indicated, TA = +25°C, VDD = +2.4V to 5.5V, VSS = GND, VCM = VDD/3, VOUT = VDD/2, VL = VDD/2, RL = 10 kΩ to VL and CL = 30 pF. 6 Overdrive Recovery Time (s) 1m Output Voltage (V) 5 VDD = 5.5 V G = -1 V/V 4 3 2 VOUT 1 VIN 0 0 0.5 1 1.5 2 2.5 3 3.5 4 Time (µs) FIGURE 2-50: Response. Slew Rate (V/µs) VDD = 2.4V 100µ tODR, low VDD = 5.5V 10µ tODR, high 1µ 1 10 100 1000 Inverting Gain Magnitude (V/V) Inverting Large Signal Step FIGURE 2-53: Output Overdrive Recovery Time vs. Inverting Gain. Falling Edge, VDD = 2.4V 15.0 13.0 0.5V Input Overdrive Falling Edge, VDD = 5.5V 11.0 Rising Edge, VDD = 2.4V 9.0 7.0 Rising Edge, VDD = 5.5V 5.0 -50 -25 0 25 50 75 100 125 Ambient Temperature (°C) FIGURE 2-51: Temperature. Slew Rate vs. Ambient 7 VDD = 5.5 V G = -10 V/V 0.5V Overdrive Output Voltage (V) 6 5 4 VOUT GVIN 3 2 1 GVIN VOUT 0 -1 Time (50 us/div) FIGURE 2-52: Output Overdrive Recovery vs. Time with G = -10 V/V. DS20005434B-page 16 2015-2016 Microchip Technology Inc. MCP6V91/1U/2/4 3.0 PIN DESCRIPTIONS Descriptions of the pins are listed in Table 3-1. TABLE 3-1: PIN FUNCTION TABLE MCP6V91 MCP6V91U MCP6V92 MCP6V94 Symbol Description SOT-23 SOT-23, SC70 2X3 TDFN MSOP TSSOP 1 4 1 1 1 4 3 2 2 3 1 3 3 5 5 8 8 4 VDD — — 5 5 5 VINB+ Noninverting Input (Op Amp B) 3.1 2 VIN– Inverting Input 3 VIN+ Noninverting Input Positive Power Supply — — 6 6 6 VINB- Inverting Input (Op Amp B) — 7 7 7 VOUTB Output (Op Amp B) — — — — 8 VOUTC Output (Op Amp C) — — — — 9 VINC- Inverting Input (Op Amp C) — — — — 10 VINC+ 2 2 4 4 11 VSS — — — — 12 VIND+ Noninverting Input (Op Amp D) — — — — 13 VIND- Inverting Input (Op Amp D) — — — — 14 VOUTD — — 9 — — EP Analog Outputs (VOUT, VOUTA, VOUTB, VOUTC, VOUTD) Analog Inputs (VIN+, VIN-, VINB+, VINB-, VINC-, VINC+, VIND-, VIND+) The noninverting and inverting inputs (VIN+, VIN–, …) are high-impedance CMOS inputs with low bias currents. 3.3 Output — The analog output pins (VOUT) are low-impedance voltage sources. 3.2 VOUT 3.4 Noninverting Input (Op Amp C) Negative Power Supply Output (Op Amp D) Exposed Thermal Pad (EP); must be connected to VSS Exposed Thermal Pad (EP) There is an internal connection between the exposed thermal pad (EP) and the VSS pin; they must be connected to the same potential on the printed circuit board (PCB). This pad can be connected to a PCB ground plane to provide a larger heat sink. This improves the package thermal resistance (θJA). Power Supply Pins (VDD, VSS) The positive power supply (VDD) is 2.4V to 5.5V higher than the negative power supply (VSS). For normal operation, the other pins are between VSS and VDD. Typically, these parts are used in a single (positive) supply configuration. In this case, VSS is connected to ground and VDD is connected to the supply. VDD will need bypass capacitors. 2015-2016 Microchip Technology Inc. DS20005434B-page 17 MCP6V91/1U/2/4 4.0 APPLICATIONS The MCP6V91/1U/2/4 family of zero-drift op amps is manufactured using Microchip’s state-of-the-art CMOS process. It is designed for precision applications with requirements for small packages and low power. Its low supply voltage and low quiescent current make the MCP6V91/1U/2/4 devices ideal for battery-powered applications. 4.1 Overview of Zero-Drift Operation Figure 4-1 shows a simplified diagram of the MCP6V91/1U/2/4 zero-drift op amp. This diagram will be used to explain how slow voltage errors are reduced in this architecture (much better VOS, VOS/TA (TC1), CMRR, PSRR, AOL and 1/f noise). VREF Output Buffer VOUT + - VIN– + - Main Amp. + - The output buffer drives external loads at the VOUT pin (VREF is an internal reference voltage). The oscillator runs at fOSC1 = 200 kHz. Its output is divided by two, to produce the chopping clock rate of fCHOP = 100 kHz. The internal Power-on Reset (POR) starts the part in a known good state, protecting against power supply brown-outs. The digital control block controls switching and POR events. 4.1.2 CHOPPING ACTION Figure 4-2 shows the amplifier connections for the first phase of the chopping clock and Figure 4-3 shows the connections for the second phase. Its slow voltage errors alternate in polarity, making the average error small. VIN+ + VIN+ The low-pass filter reduces high-frequency content, including harmonics of the chopping clock. VIN– NC + + - Main Amp. + - Low-Pass Filter Low-Pass Filter Chopper Input Switches + Aux. + - Amp. - NC + Aux. + - Amp. - Chopper Output Switches FIGURE 4-2: First Chopping Clock Phase; Equivalent Amplifier Diagram. Oscillator Digital Control POR FIGURE 4-1: Simplified Zero-Drift Op Amp Functional Diagram. 4.1.1 BUILDING BLOCKS The main amplifier is designed for high gain and bandwidth, with a differential topology. Its main input pair (+ and - pins at the top left) is used for the higher frequency portion of the input signal. Its auxiliary input pair (+ and - pins at the bottom left) is used for the low-frequency portion of the input signal and corrects the op amp’s input offset voltage. Both inputs are added together internally. The auxiliary amplifier, chopper input switches and chopper output switches provide a high DC gain to the input signal. DC errors are modulated to higher frequencies, while white noise is modulated to a low frequency. DS20005434B-page 18 VIN+ VIN– + + - Main Amp. + - NC Low-Pass Filter + Aux. + - Amp. - FIGURE 4-3: Second Chopping Clock Phase; Equivalent Amplifier Diagram. 2015-2016 Microchip Technology Inc. MCP6V91/1U/2/4 4.1.3 INTERMODULATION DISTORTION (IMD) These op amps will show intermodulation distortion (IMD) products when an AC signal is present. The signal and clock can be decomposed into sine wave tones (Fourier series components). These tones interact with the zero-drift circuitry’s nonlinear response to produce IMD tones at sum and difference frequencies. Each of the square wave clock’s harmonics has a series of IMD tones centered on it (see Figures 2-40 and 2-41). 4.2 4.2.1 Other Functional Blocks RAIL-TO-RAIL INPUTS The input stage of the MCP6V91/1U/2/4 op amps uses two differential CMOS input stages in parallel. One operates at low common-mode input voltage (VCM, which is approximately equal to VIN+ and VIN- in normal operation), and the other operates at high VCM. With this topology, the input operates with VCM up to VDD + 0.3V and down to VSS – 0.2V, at +25°C (see Figure 2-19). The input offset voltage (VOS) is measured at VCM = VSS – 0.2V and VDD + 0.3V to ensure proper operation. 4.2.1.1 Phase Reversal The input devices are designed to not exhibit phase inversion when the input pins exceed the supply voltages. Figure 2-46 shows an input voltage exceeding both supplies with no phase inversion. 4.2.1.2 VDD Bond Pad VIN+ Bond Pad VSS Bond Pad FIGURE 4-4: Structures. The ESD protection on the inputs can be depicted as shown in Figure 4-4. This structure was chosen to protect the input transistors against many (but not all) overvoltage conditions and to minimize input bias current (IB). 2015-2016 Microchip Technology Inc. Simplified Analog Input ESD The input ESD diodes clamp the inputs when they try to go more than one diode drop below VSS. They also clamp any voltages well above VDD; their breakdown voltage is high enough to allow normal operation but not low enough to protect against slow overvoltage (beyond VDD) events. Very fast ESD events (that meet the specification) are limited so that damage does not occur. In some applications, it may be necessary to prevent excessive voltages from reaching the op amp inputs; Figure 4-5 shows one approach to protecting these inputs. D1 and D2 may be small signal silicon diodes, Schottky diodes for lower clamping voltages or diode-connected FETs for low leakage. VDD U1 D1 Input Voltage Limits In order to prevent damage and/or improper operation of these amplifiers, the circuit must limit the voltages at the input pins (see Section 1.1 “Absolute Maximum Ratings †”). This requirement is independent of the input current limits discussed later on. Bond V – IN Pad Input Stage MCP6V9X V1 + D2 V2 - VOUT FIGURE 4-5: Protecting the Analog Inputs Against High Voltages. DS20005434B-page 19 MCP6V91/1U/2/4 4.2.1.3 4.3 Input Current Limits In order to prevent damage and/or improper operation of these amplifiers, the circuit must limit the currents into the input pins (see Section 1.1 “Absolute Maximum Ratings †”). This requirement is independent of the voltage limits discussed previously. Figure 4-6 shows one approach to protecting these inputs. The R1 and R2 resistors limit the possible current in or out of the input pins (and into D1 and D2). The diode currents will dump onto VDD. V1 V2 R1 MCP6V9X D2 Table 1-1 gives both the linear and quadratic temperature coefficients (TC1 and TC2) of input offset voltage. The input offset voltage, at any temperature in the specified range, can be calculated as follows: EQUATION 4-1: 2 T = TA – 25°C VOS(TA) = Input offset voltage at TA VOS = Input offset voltage at +25°C TC1 = Linear temperature coefficient TC2 = Quadratic temperature coefficient VOUT - R2 VSS – min(V1, V2) 2 mA max(V1, V2) – VDD min(R1, R2) > 2 mA min(R1, R2) > FIGURE 4-6: Protecting the Analog Inputs Against High Currents. It is also possible to connect the diodes to the left of the R1 and R2 resistors. In this case, the currents through the D1 and D2 diodes need to be limited by some other mechanism. The resistors then serve as in-rush current limiters; the DC current into the input pins (VIN+ and VIN-) should be very small. A significant amount of current can flow out of the inputs (through the ESD diodes) when the commonmode input voltage (VCM) is below ground (VSS) (see Figure 2-18). 4.2.2 INPUT OFFSET VOLTAGE OVER TEMPERATURE Where: U1 + 4.3.1 V OS T A = VOS + TC 1 T + TC2 T VDD D1 Application Tips RAIL-TO-RAIL OUTPUT The output voltage range of the MCP6V91/1U/2/4 zero-drift op amps is VDD – 9 mV (typical) and VSS + 7 mV (typical) when RL = 10 kΩ is connected to VDD/2 and VDD = 5.5V. Refer to Figures 2-20 and 2-21 for more information. This op amp is designed to drive light loads; use another amplifier to buffer the output from heavy loads. 4.3.2 DC GAIN PLOTS Figures 2-10 to 2-12 are histograms of the reciprocals (in units of µV/V) of CMRR, PSRR and AOL, respectively. They represent the change in input offset voltage (VOS) with a change in common-mode input voltage (VCM), power supply voltage (VDD) and output voltage (VOUT). The histograms are based on data taken with the production test equipment and the results reflect the trade-off between accuracy and test time. The actual performance of the devices is typically higher than shown in Figures 2-10 to 2-12. The 1/AOL histogram is centered near 0 µV/V because the measurements are dominated by the op amp’s input noise. The negative values shown represent noise and tester limitations, not unstable behavior. Production tests make multiple VOS measurements, which validates an op amp's stability; an unstable part would show greater VOS variability or the output would stick at one of the supply rails. 4.3.3 OFFSET AT POWER-UP When these parts power up, the input offset (VOS) starts at its uncorrected value (usually less than ±5 mV). Circuits with high DC gain can cause the output to reach one of the two rails. In this case, the time to a valid output is delayed by an output overdrive time (like tODR) in addition to the start-up time (like tSTR). It can be simple to avoid this extra start-up time. Reducing the gain is one method. Adding a capacitor across the feedback resistor (RF) is another method. DS20005434B-page 20 2015-2016 Microchip Technology Inc. MCP6V91/1U/2/4 SOURCE RESISTANCES The input bias currents have two significant components: switching glitches that dominate at room temperature and below, and input ESD diode leakage currents that dominate at +85°C and above. Make the resistances seen by the inputs small and equal. This minimizes the output offset caused by the input bias currents. The inputs should see a resistance on the order of 10Ω to 1 kΩ at high frequencies (i.e., above 1 MHz). This helps minimize the impact of switching glitches, which are very fast, on overall performance. In some cases, it may be necessary to add resistors in series with the inputs to achieve this improvement in performance. Small input resistances may be needed for high gains. Without them, parasitic capacitances might cause positive feedback and instability. 4.3.5 SOURCE CAPACITANCE The capacitances seen by the two inputs should be small. Large input capacitances and source resistances, together with high gain, can lead to positive feedback and instability. 4.3.6 CAPACITIVE LOADS Driving large capacitive loads can cause stability problems for voltage feedback op amps. As the load capacitance increases, the feedback loop’s phase margin decreases and the closed-loop bandwidth is reduced. This produces gain peaking in the frequency response, with overshoot and ringing in the step response. These zero-drift op amps have a different output impedance than most op amps, due to their unique topology. When driving a capacitive load with these op amps, a series resistor at the output (RISO in Figure 4-7) improves the feedback loop’s phase margin (stability) by making the output load resistive at higher frequencies. The bandwidth will be generally lower than the bandwidth with no capacitive load. GN is the circuit’s noise gain. For noninverting gains, GN and the Signal Gain are equal. For inverting gains, GN is 1+|Signal Gain| (e.g., -1 V/V gives GN = +2 V/V). 1000 Recommended R ISO (Ω) 4.3.4 VDD = 5.5 V RL = 10 kȍ 100 GN: 1 V/V 10 V/V 100 V/V 10 1 1p 10p 10n 100n 1µ After selecting RISO for your circuit, double check the resulting frequency response peaking and step response overshoot. Modify the RISO value until the response is reasonable. Bench evaluation is helpful. 4.3.7 STABILIZING OUTPUT LOADS This family of zero-drift op amps has an output impedance that has a double zero when the gain is low (see Figures 2-32 and 2-33). This can cause a large phase shift in feedback networks that have lowimpedance near the part’s bandwidth. This large phase shift can cause stability problems. Figure 4-9 shows that the load on the output is (RL + RISO)||(RF + RG), where RISO is before the load (like Figure 4-7). This load needs to be large enough to maintain stability; it should be at least 10 kΩ. RG RF RISO VOUT - RL CL + U1 VOUT + 1n FIGURE 4-8: Recommended RISO Values for Capacitive Loads. RISO - 100p Normalized Load Capacitance; CL/√ √GN (F) CL MCP6V9X FIGURE 4-9: Output Load. U1 MCP6V9X FIGURE 4-7: Output Resistor, RISO, Stabilizes Capacitive Loads. Figure 4-8 gives recommended RISO values for different capacitive loads and gains. The x-axis is the load capacitance (CL). The y-axis is the resistance (RISO). 2015-2016 Microchip Technology Inc. DS20005434B-page 21 MCP6V91/1U/2/4 4.3.8 GAIN PEAKING 4.3.9 Figure 4-10 shows an op amp circuit that represents noninverting amplifiers (VM is a DC voltage and VP is the input) or inverting amplifiers (VP is a DC voltage and VM is the input). The CN and CG capacitances represent the total capacitance at the input pins; they include the op amp’s common-mode input capacitance (CCM), board parasitic capacitance and any capacitor placed in parallel. The CFP capacitance represents the parasitic capacitance coupling the output and noninverting input pins. RN VP CN CFP U1 + MCP6V9X - VM RG FIGURE 4-10: Capacitance. CG Reduce undesired noise and signals with: • Low-bandwidth signal filters: - Minimize random analog noise - Reduce interfering signals • Good Printed Circuit Board (PCB) layout techniques: - Minimize crosstalk - Minimize parasitic capacitances and inductances that interact with fast-switching edges • Good power supply design: - Isolation from other parts - Filtering of interference on supply line(s) 4.3.10 RF VOUT Amplifier with Parasitic CG acts in parallel with RG (except for a gain of +1 V/V), which causes an increase in gain at high frequencies. CG also reduces the phase margin of the feedback loop, which becomes less stable. This effect can be reduced by reducing either CG or RF||RG. CN and RN form a low-pass filter that affects the signal at VP. This filter has a single real pole at 1/(2πRNCN). The largest value of RF that should be used depends on noise gain (see GN in Section 4.3.6 “Capacitive Loads”), CG and the open-loop gain’s phase shift. An approximate limit for RF is: EQUATION 4-2: 3.5 pF R F 10 k --------------- G N2 CG Some applications may modify these values to reduce either output loading or gain peaking (step-response overshoot). At high gains, RN needs to be small in order to prevent positive feedback and oscillations. Large CN values can also help. REDUCING UNDESIRED NOISE AND SIGNALS SUPPLY BYPASSING AND FILTERING With this family of operational amplifiers, the power supply pin (VDD for single supply) should have a local bypass capacitor (i.e., 0.01 µF to 0.1 µF) within 2 mm of the pin for good high-frequency performance. These parts also need a bulk capacitor (i.e., 1 µF or larger) within 100 mm to provide large, slow currents. This bulk capacitor can be shared with other low-noise analog parts. In some cases, high-frequency power supply noise (e.g., switched mode power supplies) may cause undue intermodulation distortion with a DC offset shift; this noise needs to be filtered. Adding a small resistor into the supply connection can be helpful. 4.3.11 PCB DESIGN FOR DC PRECISION In order to achieve DC precision on the order of ±1 µV, many physical errors need to be minimized. The design of the PCB, the wiring and the thermal environment have a strong impact on the precision achieved. A poor PCB design can easily be more than 100 times worse than the MCP6V91/1U/2/4 op amps’ minimum and maximum specifications. 4.3.11.1 PCB Layout Any time two dissimilar metals are joined together, a temperature-dependent voltage appears across the junction (the Seebeck or thermojunction effect). This effect is used in thermocouples to measure temperature. The following are examples of thermojunctions on a PCB: • Components (resistors, op amps, …) soldered to a copper pad • Wires mechanically attached to the PCB • Jumpers • Solder joints • PCB vias DS20005434B-page 22 2015-2016 Microchip Technology Inc. MCP6V91/1U/2/4 Typical thermojunctions have temperature-to-voltage conversion coefficients of 1 to 100 µV/°C (sometimes higher). 4.4 Microchip’s AN1258 “Op Amp Precision Design: PCB Layout Techniques” (DS01258) contains in-depth information on PCB layout techniques that minimize thermojunction effects. It also discusses other effects, such as crosstalk, impedances, mechanical stresses and humidity. Many sensors are configured as Wheatstone bridges. Strain gauges and pressure sensors are two common examples. These signals can be small and the common-mode noise large. Amplifier designs with high differential gain are desirable. 4.3.11.2 Crosstalk DC crosstalk causes offsets that appear as a larger input offset voltage. Common causes include: Typical Applications 4.4.1 WHEATSTONE BRIDGE Figure 4-11 shows how to interface to a Wheatstone bridge with a minimum of components. Because the circuit is not symmetric, the ADC input is single-ended and there is a minimum of filtering; the CMRR is good enough for moderate common-mode noise. • Common-mode noise (remote sensors) • Ground loops (current return paths) • Power supply coupling R R Interference from the mains (usually 50 Hz or 60 Hz) and other AC sources can also affect the DC performance. Nonlinear distortion can convert these signals to multiple tones, including a DC shift in voltage. When the signal is sampled by an ADC, these AC signals can also be aliased to DC, causing an apparent shift in offset. FIGURE 4-11: To reduce interference: 4.4.2 - Keep traces and wires as short as possible Use shielding Use ground plane (at least a star ground) Place the input signal source near the DUT Use good PCB layout techniques Use a separate power supply filter (bypass capacitors) for these zero-drift op amps 4.3.11.3 Miscellaneous Effects R R 0.2R 0.2R MCP6V91 VDD RW 2015-2016 Microchip Technology Inc. U1 + The ratiometric circuit in Figure 4-12 conditions a two-wire RTD for applications with a limited temperature range. U1 acts as a difference amplifier with a low-frequency pole. The sensor’s wiring resistance (RW) is corrected in firmware. Failure (open) of the RTD is detected by an out-of-range voltage. Make the (trace) capacitances seen by the input pins small and equal. This is helpful in minimizing switching glitch-induced offset voltages. Humidity can cause electrochemical potential voltages to appear in a circuit. Proper PCB cleaning helps, as does the use of encapsulants. + ADC - 100R RESISTANCE TEMPERATURE DETECTOR (RTD) SENSOR RT RN 34.8 kΩ 10.0 kΩ Mechanical stresses can make some capacitor types (such as some ceramics) output small voltages. Use more appropriate capacitor types in the signal path and minimize mechanical stresses and vibration. VDD Simple Design. Keep the resistances seen by the input pins as small and as near to equal as possible, to minimize bias current-related offsets. Bending a coax cable with a radius that is too small causes a small voltage drop to appear on the center conductor (the triboelectric effect). Make sure the bending radius is large enough to keep the conductors and insulation in full contact. 1 kΩ 0.01C VDD 10 nF RF 2.00 MΩ U1 + RRTD 100Ω MCP6V91 RG RF RW 10.0 kΩ 2.00 MΩ RB 4.99 kΩ 1.0 µF 10 nF 1.00 kΩ 100 nF VDD + ADC - FIGURE 4-12: RTD Sensor. DS20005434B-page 23 MCP6V91/1U/2/4 4.4.3 OFFSET VOLTAGE CORRECTION Figure 4-13 shows MCP6V91 (U2) correcting the input offset voltage of another op amp (U1). R2 and C2 integrate the offset error seen at U1’s input. The integration needs to be slow enough to be stable (with the feedback provided by R1 and R3). R4 and R5 attenuate the integrator’s output. This shifts the integrator pole down in frequency. R1 VIN R3 R2 R2 VDD/2 R4 C2 - + R5 + VOUT U1 MCP6XXX U2 VDD/2 MCP6V91 FIGURE 4-13: 4.4.4 Offset Correction. PRECISION COMPARATOR Use high gain before a comparator to improve the latter’s performance. Do not use MCP6V91/1U/2/4 as a comparator by itself; the VOS correction circuitry does not operate properly without a feedback loop. U1 VIN R1 MCP6V91 + - R2 VDD/2 R3 R4 R5 VOUT + - U2 MCP6541 FIGURE 4-14: DS20005434B-page 24 Precision Comparator. 2015-2016 Microchip Technology Inc. MCP6V91/1U/2/4 NOTES: 2015-2016 Microchip Technology Inc. DS20005434B-page 25 MCP6V91/1U/2/4 5.0 DESIGN AIDS Microchip provides the basic design aids needed for the MCP6V91/1U/2/4 family of op amps. 5.1 FilterLab® Software 5.4 Application Notes The following Microchip Application Notes are available on the Microchip web site at www.microchip. com/appnotes and are recommended as supplemental reference resources. Microchip’s FilterLab® software is an innovative software tool that simplifies analog active filter (using op amps) design. Available at no cost from the Microchip web site at www.microchip.com/filterlab, the FilterLab design tool provides full schematic diagrams of the filter circuit with component values. It also outputs the filter circuit in SPICE format, which can be used with the macro model to simulate actual filter performance. ADN003: “Select the Right Operational Amplifier for your Filtering Circuits” (DS21821) 5.2 AN990: “Analog Sensor Conditioning Circuits – An Overview” (DS00990) Microchip Advanced Part Selector (MAPS) MAPS is a software tool that helps efficiently identify Microchip devices that fit a particular design requirement. Available at no cost from the Microchip web site at www.microchip.com/maps, MAPS is an overall selection tool for Microchip’s product portfolio that includes Analog, Memory, MCUs and DSCs. Using this tool, a customer can define a filter to sort features for a parametric search of devices and export side-by-side technical comparison reports. Helpful links are also provided for data sheets, purchase and sampling of Microchip parts. 5.3 Analog Demonstration and Evaluation Boards AN722: “Operational Amplifier Topologies and DC Specifications” (DS00722) AN723: “Operational Amplifier AC Specifications and Applications” (DS00723) AN884: “Driving Capacitive Loads With Op Amps” (DS00884) AN1177: “Op Amp Precision Design: DC Errors” (DS01177) AN1228: “Op Amp Precision Design: Random Noise” (DS01228) AN1258: “Op Amp Precision Design: PCB Layout Techniques” (DS01258) AN1767: “Solutions for Radio Frequency Electromagnetic Interference in Amplifier Circuits” (DS00001767) These Application Notes and others are listed in the design guide: “Signal Chain Design Guide” (DS21825) Microchip offers a broad spectrum of Analog Demonstration and Evaluation Boards that are designed to help customers achieve faster time to market. For a complete listing of these boards and their corresponding user’s guides and technical information, visit the Microchip web site at www.microchip.com/analog tools. Some boards that are especially useful are: • MCP6V01 Thermocouple Auto-Zeroed Reference Design (MCP6V01RD-TCPL) • MCP6XXX Amplifier Evaluation Board 1 (DS51667) • MCP6XXX Amplifier Evaluation Board 2 (DS51668) • MCP6XXX Amplifier Evaluation Board 3 (DS51673) • MCP6XXX Amplifier Evaluation Board 4 (DS51681) • Active Filter Demo Board Kit User’s Guide (DS51614) • 8-Pin SOIC/MSOP/TSSOP/DIP Evaluation Board (SOIC8EV) • 14-Pin SOIC/TSSOP/DIP Evaluation Board (SOIC14EV) DS20005434B-page 26 2015-2016 Microchip Technology Inc. MCP6V91/1U/2/4 NOTES: 2015-2016 Microchip Technology Inc. DS20005434B-page 27 MCP6V91/1U/2/4 6.0 PACKAGING INFORMATION 6.1 Package Marking Information 5-Lead SC70 (MCP6V91U) Example Device MCP6V91UT-E/LTY Code DWNN 5-Lead SOT-23 (MCP6V91, MCP6V91U) XXXXY WWNNN Device DW56 Example Code AABJ5 MCP6V91T-E/OT AABJY 10256 MCP6V91UT-E/OT AABKY 8-Lead MSOP (MCP6V92) Example 6V92 544256 8-Lead TDFN (MCP6V92) Example Device MCP6V92T-E/MNY Note: DS20005434B-page 28 Code ACY Applies to 8-Lead 2x3 TDFN. ACY 544 25 2015-2016 Microchip Technology Inc. MCP6V91/1U/2/4 14-Lead TSSOP (MCP6V94) XXXXXXXX YYWW NNN Legend: XX...X Y YY WW NNN e3 * Note: Example MCP6V94 1544 256 Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week ‘01’) Alphanumeric traceability code Pb-free JEDEC® designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. 2015-2016 Microchip Technology Inc. DS20005434B-page 29 MCP6V91/1U/2/4 5-Lead Plastic Small Outine Transistor (LTY) [SC70] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging D b 3 1 2 E1 E 4 5 e A e A2 c A1 L * , .1 2 +,,+%- +. ./ . 0 ! 2 /' 4 5 6 2 7 %7 5 6 6 3! "# /' 8 5 2 7 8 ! ! 9! /' , 5 ! : 3 , , , %7 5 6 3 , 8 1 ! 6 ! "#$ " % & ' ( ( Technology Drawing Microchip % & ( # C04-083B ;3" DS20005434B-page 30 2015-2016 Microchip Technology Inc. MCP6V91/1U/2/4 5-Lead Plastic Small Outine Transistor (LTY) [SC70] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2015-2016 Microchip Technology Inc. DS20005434B-page 31 MCP6V91/1U/2/4 : 7 ( = $>>((( > 7 2 7 b N E E1 3 2 1 e e1 D A2 A c φ A1 L L1 * , .1 2 , 2 / , 2 +,,+%- +. ./ . ! <! "# 0 < "# /' 4 < 6 2 7 %7 5< 6 9 6 ! /' 8 6 9 2 7 8 9 6 5 /' , 6 9 ! : , , 6 3 : , 9! 6 5 : ? 6 9? 5 6 3 , %7 , 8 1 6 ! ! "#$ " % & ' ( ( % & ( # ;<" DS20005434B-page 32 2015-2016 Microchip Technology Inc. MCP6V91/1U/2/4 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2015-2016 Microchip Technology Inc. DS20005434B-page 33 MCP6V91/1U/2/4 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS20005434B-page 34 2015-2016 Microchip Technology Inc. MCP6V91/1U/2/4 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2015-2016 Microchip Technology Inc. DS20005434B-page 35 MCP6V91/1U/2/4 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS20005434B-page 36 2015-2016 Microchip Technology Inc. MCP6V91/1U/2/4 8-Lead Plastic Dual Flat, No Lead Package (MNY) – 2x3x0.75mm Body [TDFN] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging D A B N (DATUM A) (DATUM B) E NOTE 1 2X 0.15 C 1 2 2X 0.15 C TOP VIEW 0.10 C C (A3) A SEATING PLANE 8X 0.08 C A1 SIDE VIEW 0.10 C A B D2 L 1 2 0.10 C A B NOTE 1 E2 K N 8X b e 0.10 0.05 C A B C BOTTOM VIEW Microchip Technology Drawing No. C04-129-MNY Rev D Sheet of 2 2015-2016 Microchip Technology Inc. DS20005434B-page 37 MCP6V91/1U/2/4 8-Lead Plastic Dual Flat, No Lead Package (MNY) – 2x3x0.75mm Body [TDFN] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging Units Dimension Limits N Number of Pins e Pitch A Overall Height A1 Standoff Contact Thickness A3 D Overall Length E Overall Width Exposed Pad Length D2 Exposed Pad Width E2 b Contact Width L Contact Length Contact-to-Exposed Pad K MIN 0.70 0.00 1.45 1.60 0.20 0.25 0.20 MILLIMETERS NOM 8 0.50 BSC 0.75 0.02 0.20 REF 2.00 BSC 3.00 BSC 0.25 0.30 - MAX 0.80 0.05 1.65 1.80 0.30 0.45 - Notes: 1. Pin 1 visual index feature may vary, but must be located within the hatched area. 2. Package may have one or more exposed tie bars at ends. 3. Package is saw singulated 4. Dimensioning and tolerancing per ASME Y14.5M BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. Microchip Technology Drawing No. C04-129-MNY Rev D Sheet 2 of 2 DS20005434B-page 38 2015-2016 Microchip Technology Inc. MCP6V91/1U/2/4 8-Lead Plastic Dual Flat, No Lead Package (MNY) – 2x3x0.75mm Body [TDFN] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging X2 EV 8 ØV C Y2 EV Y1 1 2 SILK SCREEN X1 E RECOMMENDED LAND PATTERN Units Dimension Limits E Contact Pitch Optional Center Pad Width X2 Optional Center Pad Length Y2 Contact Pad Spacing C Contact Pad Width (X8) X1 Contact Pad Length (X8) Y1 Thermal Via Diameter V Thermal Via Pitch EV MIN MILLIMETERS NOM 0.50 BSC MAX 1.65 1.80 2.90 0.25 0.85 0.30 1.00 Notes: 1. Dimensioning and tolerancing per ASME Y14.5M BSC: Basic Dimension. Theoretically exact value shown without tolerances. 2. For best soldering results, thermal vias, if used, should be filled or tented to avoid solder loss during reflow process Microchip Technology Drawing No. C04-129-MNY Rev. A 2015-2016 Microchip Technology Inc. DS20005434B-page 39 MCP6V91/1U/2/4 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS20005434B-page 40 2015-2016 Microchip Technology Inc. MCP6V91/1U/2/4 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2015-2016 Microchip Technology Inc. DS20005434B-page 41 MCP6V91/1U/2/4 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS20005434B-page 42 2015-2016 Microchip Technology Inc. MCP6V91/1U/2/4 APPENDIX A: REVISION HISTORY Revision B (March 2016) The following is the list of modifications: 1. 2. 3. 4. 5. 6. Added new devices to the family: MCP6V92 and MCP6V94, and related information throughout the document. Added Figure 2-37. Updated Table 3-1 in Section 3.0, Pin Descriptions. Added markings and specification drawings for the new packages in Section 6.0, Packaging Information. Updated the Product Identification System section with the new packages. Corrected typographical errors. Revision A (September 2015) • Original release of this document. 2015-2016 Microchip Technology Inc. DS20005434B-page 43 MCP6V91/1U/2/4 NOTES: DS20005434B-page 44 2015-2016 Microchip Technology Inc. MCP6V91/1U/2/4 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. [X](1) –X Device Tape and Reel Temperature Range Device: /XX Package MCP6V91T: Single Op Amp (Tape and Reel) (SOT-23 only) MCP6V91UT: Single Op Amp (Tape and Reel) (SC-70, SOT-23) MCP6V92: Dual Op Amp (MSOP, 2x3 TDFN) MCP6V92T: Dual Op Amp (Tape and Reel) (MSOP, 2x3 TDFN) MCP6V94: Quad Op Amp (TSSOP) MCP6V94T: Quad Op Amp (Tape and Reel) (TSSOP) Temperature Range: E Package: LTY* = Plastic Small Outline Transistor, SC-70, 5-lead OT = Plastic Small Outline Transistor, SOT-23, 5-lead MNY* = Plastic Dual Flat, No-Lead - 2×3×0.75 mm Body, TDFN, 8-lead MS = Plastic Micro Small Outline, MSOP, 8-lead ST = Plastic Thin Shrink Small Outline - 4.4 mm Body, TSSOP, 14-lead *Y = -40°C to +125°C (Extended) = Nickel palladium gold manufacturing designator. Only available on the SC70 and TDFN packages. 2015-2016 Microchip Technology Inc. Examples: a) MCP6V91T-E/OT: a) MCP6V91UT-E/LTY: Tape and Reel Extended temperature, 5LD SC70 package MCP6V91UT-E/OT: Tape and Reel, Extended temperature, 5LD SOT-23 package b) a) b) c) Tape and Reel, Extended temperature, 5LD SOT-23 package MCP6V92-E/MS: Extended temperature, 8LD MSOP package MCP6V92T-E/MS: Tape and Reel, Extended temperature, 8LD MSOP package MCP6V92T-E/MNY: Tape and Reel, Extended temperature, 8LD 2x3 TDFN package a) MCP6V94-E/ST: b) MCP6V94T-E/ST: Note 1: Extended temperature, 14LD TSSOP package Tape and Reel, Extended temperature, 14LD TSSOP package Tape and Reel identifier only appears in the catalog part number description. This identifier is used for ordering purposes and is not printed on the device package. Check with your Microchip Sales Office for package availability with the Tape and Reel option. DS20005434B-page 45 MCP6V91/1U/2/4 NOTES: DS20005434B-page 46 2015-2016 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights unless otherwise stated. Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. QUALITY MANAGEMENT SYSTEM CERTIFIED BY DNV == ISO/TS 16949 == 2015-2016 Microchip Technology Inc. Trademarks The Microchip name and logo, the Microchip logo, AnyRate, dsPIC, FlashFlex, flexPWR, Heldo, JukeBlox, KeeLoq, KeeLoq logo, Kleer, LANCheck, LINK MD, MediaLB, MOST, MOST logo, MPLAB, OptoLyzer, PIC, PICSTART, PIC32 logo, RightTouch, SpyNIC, SST, SST Logo, SuperFlash and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. ClockWorks, The Embedded Control Solutions Company, ETHERSYNCH, Hyper Speed Control, HyperLight Load, IntelliMOS, mTouch, Precision Edge, and QUIET-WIRE are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Any Capacitor, AnyIn, AnyOut, BodyCom, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, Dynamic Average Matching, DAM, ECAN, EtherGREEN, In-Circuit Serial Programming, ICSP, Inter-Chip Connectivity, JitterBlocker, KleerNet, KleerNet logo, MiWi, motorBench, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation, PICDEM, PICDEM.net, PICkit, PICtail, PureSilicon, RightTouch logo, REAL ICE, Ripple Blocker, Serial Quad I/O, SQI, SuperSwitcher, SuperSwitcher II, Total Endurance, TSHARC, USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries. GestIC is a registered trademarks of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. © 2015-2016, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. ISBN: 978-1-5224-0312-8 DS20005434B-page 47 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Germany - Dusseldorf Tel: 49-2129-3766400 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Hong Kong Tel: 852-2943-5100 Fax: 852-2401-3431 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8569-7000 Fax: 86-10-8528-2104 Austin, TX Tel: 512-257-3370 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Novi, MI Tel: 248-848-4000 Houston, TX Tel: 281-894-5983 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 New York, NY Tel: 631-435-6000 San Jose, CA Tel: 408-735-9110 Canada - Toronto Tel: 905-673-0699 Fax: 905-673-6509 China - Dongguan Tel: 86-769-8702-9880 China - Hangzhou Tel: 86-571-8792-8115 Fax: 86-571-8792-8116 Germany - Karlsruhe Tel: 49-721-625370 India - Pune Tel: 91-20-3019-1500 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Japan - Osaka Tel: 81-6-6152-7160 Fax: 81-6-6152-9310 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Japan - Tokyo Tel: 81-3-6880- 3770 Fax: 81-3-6880-3771 Italy - Venice Tel: 39-049-7625286 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 China - Hong Kong SAR Tel: 852-2943-5100 Fax: 852-2401-3431 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenzhen Tel: 86-755-8864-2200 Fax: 86-755-8203-1760 Taiwan - Hsin Chu Tel: 886-3-5778-366 Fax: 886-3-5770-955 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Kaohsiung Tel: 886-7-213-7828 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Poland - Warsaw Tel: 48-22-3325737 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 Sweden - Stockholm Tel: 46-8-5090-4654 UK - Wokingham Tel: 44-118-921-5800 Fax: 44-118-921-5820 Taiwan - Taipei Tel: 886-2-2508-8600 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 07/14/15 DS20005434B-page 48 2015-2016 Microchip Technology Inc.