1.25 Gbps Single Mode Transceiver C-13-1250(C)-T(3)-SSC(2) Features • SC Duplex Single Mode Transceiver • Industry Standard 1x9 Footprint • Gigabit Ethernet Compliant • Single +3.3/5V Power Supply • PECL Differential Inputs and Outputs • PECL/LVPECL Signal Detection Output [C-13-1250-T(3)-SSC(2)] • TTL/LVTTL Signal Detection Output [C-13-1250C-T(3)-SSC(2)] • Wave Solderable and Aqueous Washable • Uncooled laser diode with MQW structure • Complies with Telcordia (Bellcore) GR-468-CORE • Gigabit Ethernet Application • RoHS compliance available Absolute Maximum Rating Parameter Symbol Min. Max. Unit Note Power Supply Voltage Vcc 0 3.6 V C-13-1250(C)-T3-SSC(2) Power Supply Voltage Vcc 0 6 V C-13-1250(C)-T-SSC(2) Output Current Iout 0 30 mA - - 260 ºC Tstg -40 85 ºC Soldering Temperature Storage Temperature 10 seconds on leads only Recommended Operating Condition Parameter Symbol Min. Typ. Max. Unit Power Supply Voltage 1 Vcc 3.1 3.3 3.5 V Power Supply Voltage 1 Vcc 4.75 5 5.25 V Operating Temperature1 Operating Temperature1 Topr 0 - 70 ºC Topr -40 - 85 ºC - - 1250 - Mbps Data Rate Note1: Please refer to ordering information LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 1 LUMNDS601-May1806 Rev A.3 1.25 Gbps Single Mode Transceiver C-13-1250(C)-T(3)-SSC(2) Transmitter Specifications Parameter Symbol Min Typical Max Unit Optical Transmit Power Po -10 - -3 dBm C-13-1250(C)-T(3)-SSC Optical Transmit Power Po -5 - 0 dBm C-13-1250(C)-T(3)-SSC2 Output center Wavelength λ 1270 1310 1355 nm C-13-1250(C)-T(3)-SSC Output center Wavelength λ 1275 1310 1350 nm C-13-1250(C)-T(3)-SSC2 Output Spectrum Width ∆λ - - 4 nm RMS(σ), C-13-1250(C)-T(3)-SSC Output Spectrum Width ∆λ - - 2.5 nm RMS(σ), C-13-1250(C)-T(3)-SSC2 Extinction Ratio ER 9 - - dB 0.26 ns 20% to 80% Values 20% to 80% Values Output Eye Optical Rise Time Optical Fall Time Compliant with IEEE 802.3 tr - - tf - - 0.26 ns RIN - - -120 dB/Hz TJ - - 0.27 ns Symbol Min Typical Max Unit ICC - - 180 mA Data Input Current-Low IIL -350 - - µA Data Input Current-High IIH - - 350 µA Differential Input Voltage VIH-VIL 300 - - mV Data Input Voltage-Low VIL-VCC -2.0 - -1.58 V Data Input Voltage-High VIH-VCC -1.1 - -0.74 V Relative Intensity Noise Total Jitter Notes Measured with 27-1 PRBS Transmitter Specifications Parameter Power Supply Current LUMINENTOIC.COM Notes Maximum current is specified at Vcc= Maximum @ maximum temperature These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2 LUMNDS601-May1806 Rev A.3 1.25 Gbps Single Mode Transceiver C-13-1250(C)-T(3)-SSC(2) Receiver Specifications Parameter Sensitivity2 Symbol Min Typical Max Unit - - - -24 dBm Maximum Input Power Pin 0 - - dBm Signal Detect-Asserted Pa - - -24 dBm Measured on transition: low to high Signal Detect-Deasserted Pd -38 - - dBm Measured on transition: high to low 1 - - dB 1100 - 1600 nm Symbol Min Typical Max Unit Note ICC - - 100 mA The current excludes the output load current Data output Voltage-Low VOL -Vcc -2.0 - -1.58 V Data output Voltage-High VOH- Vcc -1.1 - -0.74 V These outputs are compatible with 10K, 10KH and 100KECL and LVPECL outputs Signal Detect Output Voltage-Low VSDL - - 0.5 V Signal Detect Output Voltage-High VSDH 2.0 - - V Signal Detect Output Voltage-Low VSDL-Vcc -2.0 - -1.58 V Signal Detect Output Voltage-High VSDH- Vcc -1.1 - -0.74 V Signal Detect-Hysteresis Wavelength of Operation Notes Note 2: Measured with 27-1 PRBS, BER= 10-12 Receiver Specifications Parameter Power Supply Current LUMINENTOIC.COM C-13-1250C-T(3)-SSC(2) C-13-1250-T(3)-SSC(2) 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 3 LUMNDS601-May1806 Rev A.3 1.25 Gbps Single Mode Transceiver C-13-1250(C)-T(3)-SSC(2) Connection Diagram 1. (Rx GND) 2. (Rx +) 3. (Rx-) 4. (SD) 5. (Rx Vcc) 6. (Tx Vcc) 7. (TX-) 8. (TX+) 9. (Tx GND) NC Top View NC Receiver Signal Ground Receiver Data Out Receiver Data Out Bar Signal Detect Receiver Power Supply Transmitter Power Supply Transmitter Data In Bar Transmitter Data In Transmitter Signal Ground PIN Symbol 1 RxGND 2 RD+ See recommended circuit schematic 3 RD- See recommended circuit schematic 4 SD 5 RxVcc 6 TxVcc DC power for the transmitter section 7 TD- See recommended circuit schematic 8 Warnings TD+ See recommended circuit schematic 9 LUMINENTOIC.COM Notes Directly connect this pin to the receiver ground plane Active high on this indicates a received optical signal DCc power for the receiver section TxGND Directly connect this pin to the transmitter ground plane 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 4 LUMNDS601-May1806 Rev A.3 1.25 Gbps Single Mode Transceiver C-13-1250(C)-T(3)-SSC(2) Recommended Circuit Schematic C-13-1250-T(3)-SSC(2) Tx Vcc C5 Rx Vcc 9 R1 7 8 6 5 4 3 2 1 R3 R9 R5 C6 R7 TD + RD + TD - RD - Tx Vcc SD Rx Vcc R2 R4 Notes +3.3V: R1=R3=R5=R7=R9=130 R2=R4=R6=R8=R10=82 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H No internal connection Transceiver Top view No internal connection R10 R6 R8 L1 Notes +5V: R1=R3=R5=R7=R9=82 R2=R4=R6=R8=R10=130 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H Vcc C1 C3 L2 C2 C4 Rx Vcc Tx Vcc C-13-1250C-T(3)-SSC(2) Tx Vcc C5 Rx Vcc 9 R1 7 8 6 5 4 3 2 1 R5 R3 C6 R7 TD + RD + TD - RD - Tx Vcc SD Rx Vcc R2 R4 Notes +3.3V: R1=R3=R5=R7=130 R2=R4=R6=R8=82 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H No internal connection Transceiver Top view Notes +5V: R1=R3=R5=R7=82 R2=R4=R6=R8=130 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H R6 No internal connection R8 L1 Vcc C3 C1 L2 C4 C2 Rx Vcc Tx Vcc The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc. A GND plane under the module is required for good EMI and sensitivity performance. LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 5 LUMNDS601-May1806 Rev A.3 1.25 Gbps Single Mode Transceiver C-13-1250(C)-T(3)-SSC(2) Package Diagram (10.4 mm SC transceiver assembly) Top View Front View Side View Rear View Units: mm Package Option: Blank, A = black case LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 6 LUMNDS601-May1806 Rev A.3 1.25 Gbps Single Mode Transceiver C-13-1250(C)-T(3)-SSC(2) Package Diagram (9.8 mm SC transceiver assembly) Front View Top View Units: mm x8 Rear View Side View Package Option : B, E = Blue case C, D = Black case LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 7 LUMNDS601-May1806 Rev A.3 1.25 Gbps Single Mode Transceiver C-13-1250(C)-T(3)-SSC(2) Ordering Information Available Options: C-13-1250-T-SSC(A/B/C/D/E) C-13-1250C-T-SSC(A/B/C/D/E) C-13-1250-T3-SSC(A/B/C/D/E) C-13-1250C-T3-SSC(A/B/C/D/E) C-13-1250-T-SSC2(A/B/C/D/E) C-13-1250C-T-SSC2(A/B/C/D/E) C-13-1250-T3-SSC2(A/B/C/D/E) C-13-1250C-T3-SSC2(A/B/C/D/E) C-13-1250-T-SSC(A/B/C/D/E)-G5 C-13-1250C-T-SSC(A/B/C/D/E)-G5 C-13-1250-T3-SSC(A/B/C/D/E)-G5 C-13-1250C-T3-SSC(A/B/C/D/E)-G5 C-13-1250-T-SSC2(A/B/C/D/E)-G5 C-13-1250C-T-SSC2(A/B/C/D/E)-G5 C-13-1250-T3-SSC2(A/B/C/D/E)-G5 C-13-1250C-T3-SSC2(A/B/C/D/E)-G5 C-13-1250-T-SSC(A/B/C/D/E)-GR C-13-1250C-T-SSC(A/B/C/D/E)-GR C-13-1250-T3-SSC(A/B/C/D/E)-GR C-13-1250C-T3-SSC(A/B/C/D/E)-GR C-13-1250-T-SSC2(A/B/C/D/E)-GR C-13-1250C-T-SSC2(A/B/C/D/E)-GR C-13-1250-T3-SSC2(A/B/C/D/E)-GR C-13-1250C-T3-SSC2(A/B/C/D/E)-GR Part numbering Definition: C - 13 - 1250(C) - T(3) - S SC TxPower Temperature and Package RoHs • 13 = Wavelength 1310nm • Communication protocol (1250 Mbps) 1250 = PECL Signal Detection Output 1250C = TTL Signal Detection Output • T = +5V Transceiver, FP T3= +3.3V Transceier, FP • Single mode fiber • Connector options • Tx Power range Blank = -3 to -10 dBm 2 = -5 to 0 dBm • Temperature range and package Blank = commercial temperature(0 to 70 ºC), 10.4 mm, Black case A = industrial temperature(-40 to 85 ºC), 10.4 mm, Black case B = industrial temperature(-40 to 85 ºC), 9.8 mm, Blue case C = industrial temperature(-40 to 85 ºC), 9.8 mm, Black case D = commercial temperature(0 to 70 ºC), 9.8 mm, Black case E = commercial temperature(0 to 70 ºC), 9.8 mm, Blue case • RoHS compliance available Blank = RoHS non-compliant product G5 = RoHS 5/6-compliant product (lead exemption) GR = Full RoHS compliant product (no exemption) LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 8 LUMNDS601-May1806 Rev A.3 1.25 Gbps Single Mode Transceiver C-13-1250(C)-T(3)-SSC(2) Warnings: Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Legal Notes: IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © LuminentOIC, Inc. 2003 All rights reserved LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 9 LUMNDS601-May1806 Rev A.3