OBSOLETE PRODUCT NO RECOMMENDED REPLACEMENT contact our Technical Support Center at 1-888-INTERSIL or www.intersil.com/tsc DATASHEET ISL6504, ISL6504A FN9062 Rev 2.00 Apr 13, 2004 Multiple Linear Power Controller with ACPI Control Interface The ISL6504 and ISL6504A complement other power building blocks (voltage regulators) in ACPI-compliant designs for microprocessor and computer applications. The IC integrates three linear controllers/regulators, switching, monitoring and control functions into a 16-pin wide-body SOIC or 20-pin QFN 6x6 package. The ISL6504, ISL6504A operating mode (active outputs or sleep outputs) is selectable through two digital control pins, S3 and S5. One linear controller generates the 3.3VDUAL/3.3VSB voltage plane from the ATX supply’s 5VSB output, powering the south bridge and the PCI slots through an external NPN pass transistor during sleep states (S3, S4/S5). In active state (during S0 and S1/S2), the 3.3VDUAL/3.3VSB linear regulator uses an external N-channel pass MOSFET to connect the outputs directly to the 3.3V input supplied by an ATX power supply, for minimal losses. A controller powers up the 5VDUAL plane by switching in the ATX 5V output through an NMOS transistor in active states, or by switching in the ATX 5VSB through a PMOS (or PNP) transistor in S3 sleep state. In S4/S5 sleep states, the ISL6504 5VDUAL output is shut down. In the ISL6504A, the 5VDUAL output stays on during S4/S5 sleep states. This is the only difference between the two parts; see Table 1. Features • Provides four ACPI-Controlled Voltages - 5VDUAL USB/Keyboard/Mouse - 3.3VDUAL/3.3VSB PCI/Auxiliary/LAN - 1.2VVID Processor VID Circuitry - 1.5VSB ICH4 Resume Well • Excellent Output Voltage Regulation - All Outputs: 2.0% over temperature (as applicable) • Small Size; Very Low External Component Count • Undervoltage Monitoring of All Outputs with Centralized FAULT Reporting and Temperature Shutdown • QFN Package: - Near Chip Scale Package Footprint; Improved PCB Efficiency; Thinner profile • Pb-Free Available (RoHS Compliant) Applications • ACPI-Compliant Power Regulation for Motherboards - ISL6504: 5VDUAL is shut down in S4/S5 sleep states - ISL6504A: 5VDUAL stays on in S4/S5 sleep states An internal linear regulator supplies the 1.2V for the voltage identification circuitry (VID) only during active states (S0 and S1/S2), and uses the 3V3 pin as input source for its internal pass element. Another internal regulator outputs a 1.5VSB chip-set standby supply, which uses the 3V3DL pin as input source for its internal pass element. The 3.3VDUAL/3.3VSB and 1.5VSB outputs are active for as long as the ATX 5VSB voltage is applied to the chip. FN9062 Rev 2.00 Apr 13, 2004 Page 1 of 17 ISL6504, ISL6504A Pinouts ISL6504/A (WIDE BODY SOIC) TOP VIEW 16 5VSB 1 1V5SB 3V3DLSB 2 15 VID_CT 3V3DL 3 14 VID_PG 13 SS 1V2VID 4 12 5VDL 3V3 5 Ordering Information PART NUMBER TEMP. RANGE (oC) PACKAGE PKG. DWG. # ISL6504CB 0 to 70 16 Ld SOIC M16.3 ISL6504CBZ (Note) 0 to 70 16 Ld SOIC (Pb-free) M16.3 S3 6 11 5VDLSB ISL6504CBN 0 to 70 16 Ld SOIC M16.15 S5 7 10 DLA ISL6504CBNZ (Note) 0 to 70 16 Ld SOIC (Pb-free) M16.15 ISL6504CR 0 to 70 20 Ld 6x6 QFN L20.6x6 ISL6504CRZ (Note) 0 to 70 20 Ld 6x6 QFN (Pb-free) L20.6x6 9 GND 8 FAULT NOTE: SOIC layout should accomodate both wide and narrow footprints. 3V3DLSB 1V5SB NC 5VSB VID_CT ISL6504/A (6X6 QFN) TOP VIEW 20 19 18 17 16 ISL6504EVAL1 Evaluation Board ISL6504ACB 0 to 70 16 Ld SOIC M16.3 ISL6504ACBZ (Note) 0 to 70 16 Ld SOIC (Pb-free) M16.3 3V3DL 1 15 VID_PG ISL6504ACBN 0 to 70 16 Ld SOIC M16.15 NC 2 14 SS 0 to 70 3 13 NC 16 Ld SOIC (Pb-free) M16.15 1V2VID ISL6504ACBNZ (Note) ISL6504ACR 0 to 70 20 Ld 6x6 QFN L20.6x6 3V3 4 12 5VDL 11 5VDLSB 20 Ld 6x6 QFN (Pb-free) L20.6x6 5 ISL6504ACRZ (Note) 0 to 70 S3 10 DLA 9 FAULT 8 GND 7 S5 NC 6 NOTE: The QFN bottom pad is electrically connected to the IC substrate, at GND potential. It can be left unconnected, or connected to GND; do NOT connect to another potential. FN9062 Rev 2.00 Apr 13, 2004 ISL6504AEVAL1 Evaluation Board Add “-T” suffix for tape and reel. NOTE: Intersil Pb-free products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. Page 2 of 17 3V3DL 3V3DLSB 3V3 5VSB DLA ISL6504, ISL6504A 5VDLSB EA4 + - FN9062 Rev 2.00 Apr 13, 2004 Block Diagram 5VSB POR 4.4V/3.4V 3V3 MONITOR TEMPERATURE MONITOR (TMON) 2.75V/2.60V EA3 1V5SB + TO UV DETECTOR MONITOR AND CONTROL TO 3V3 FAULT TO UV DETECTOR UV DETECTOR + - EA3 1V2VID + 10mA 1.265V - + - UV COMP + - VID_PG + 4.10V Page 3 of 17 5VDL 10mA - GND SS S3 S5 VID_CT FIGURE 1. ISL6504, ISL6504A Simplified Power System Diagram +5VIN +12VIN +5VSB +3.3VIN 1.5VSB LINEAR REGULATOR 1.5V 1.2VVID LINEAR REGULATOR 1.2V Q2 LINEAR CONTROLLER Q3 3.3VDUAL /3.3VSB VID_PG Q4 3.3V FAULT Q5 CONTROL ISL6504/A 5VDUAL LOGIC 5V SHUTDOWN SX 2 FIGURE 2. Typical Application +5VIN +12VIN +5VSB +3.3VIN 5VSB 3V3 VOUT1 1V5SB 1.5VSB 1.2VVID RDLA VID_CT Q2 VOUT3 COUT2 CCT_VID 3V3DLSB Q1 3.3VDUAL/3.3VSB VOUT2 1V2VID COUT1 VID_PG 3V3DL VID PGOOD ISL6504/A COUT3 Q3 5VDLSB FAULT SLP_S3 SLP_S5 FAULT DLA S3 Q4 S5 VOUT4 5VDL SS COUT4 5VDUAL CSS SHUTDOWN GND FIGURE 3. FN9062 Rev 2.00 Apr 13, 2004 Page 4 of 17 ISL6504, ISL6504A Absolute Maximum Ratings Thermal Information Supply Voltage, V5VSB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7.0V DLA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to +14.5V All Other Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+ 7.0V ESD Classification (Human Body Model) . . . . . . . . . . . . . . . . . .2kV Thermal Resistance (Typical) JA (oC/W) JC (oC/W) SOIC Package (Note 1) . . . . . . . . . . . 70 N/A QFN Package (Note 2) . . . . . . . . . . . . 32 4.0 Maximum Junction Temperature (Plastic Package) . . . . . . . .150oC Maximum Storage Temperature Range . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300oC (SOIC - Lead Tips Only) For Recommended soldering conditions see Tech Brief TB389. Recommended Operating Conditions Supply Voltage, V5VSB . . . . . . . . . . . . . . . . . . . . . . . . . . . +5V 5% Lowest 5VSB Supply Voltage Guaranteeing Parameters . . . . +4.5V Digital Inputs, VSx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0 to +5.5V Ambient Temperature Range. . . . . . . . . . . . . . . . . . . . . 0oC to 70oC Junction Temperature Range . . . . . . . . . . . . . . . . . . . 0oC to 125oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. 2. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. JC, the “case temp” is measured at the center of the exposed metal pad on the package underside. See Tech Brief TB379. Electrical Specifications Recommended Operating Conditions, Unless Otherwise Noted Refer to Figures 1, 2 and 3 PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS - 17 - mA - 4 - mA Rising 5VSB POR Threshold - - 4.5 V 5VSB POR Hysteresis - 0.9 - V Rising 3V3 Threshold - 2.75 - V 3V3 Hysteresis - 150 - mV Falling Threshold Timeout (All Monitors) - 10 - s VCC SUPPLY CURRENT Nominal Supply Current Shutdown Supply Current I5VSB I5VSB(OFF) VSS = 0.8V POWER-ON RESET, SOFT-START, AND VOLTAGE MONITORS Soft-Start Current ISS - 10 - A Shutdown Voltage Threshold VSD - - 0.8 V VID_PG Rising Threshold - 1.02 - V VID_PG Hysteresis - 56 - mV - - 2.0 % - 1.5 - V 1V5SB Undervoltage Rising Threshold - 1.25 - V 1V5SB Undervoltage Hysteresis - 75 - mV 85 - - mA - - 2.0 % - 1.2 - V 1V2VID Undervoltage Rising Threshold - 0.96 - V 1V2VID Undervoltage Hysteresis - 60 - mV 40 - - mA 1.5VSB LINEAR REGULATOR (VOUT1) Regulation 1V5SB Nominal Voltage Level 1V5SB Output Current V1V5SB I1V5SB V3V3DL = 3.3V 1.2VVID LINEAR REGULATOR (VOUT2) Regulation 1V2VID Nominal Voltage Level 1V2VID Output Current FN9062 Rev 2.00 Apr 13, 2004 V1V2VID I1V2VID V3V3 = 3.3V Page 5 of 17 ISL6504, ISL6504A Electrical Specifications Recommended Operating Conditions, Unless Otherwise Noted Refer to Figures 1, 2 and 3 (Continued) PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS - - 2.0 % - 3.3 - V 3V3DL Undervoltage Rising Threshold - 2.75 - V 3V3DL Undervoltage Hysteresis - 150 - mV 5 8 - mA 5VDL Undervoltage Rising Threshold - 4.10 - V 5VDL Undervoltage Hysteresis - 200 - mV -20 - -40 mA 20 25 30 ms - 200 - s - 10 - A High Level Input Threshold - - 2.2 V Low Level Input Threshold 0.8 - - V - 50 - k - 100 - 125 - - oC - 155 - oC 3.3VDUAL/3.3VSB LINEAR REGULATOR (VOUT3) Sleep State Regulation 3V3DL Nominal Voltage Level 3V3DLSB Output Drive Current V3V3DL I3V3DLSB V5VSB = 5V 5VDUAL SWITCH CONTROLLER (VOUT4) 5VDLSB Output Drive Current I5VDLSB V5VDLSB = 4V, V5VSB = 5V TIMING INTERVALS Active State Assessment Past Input UV Thresholds (Note 3) Active-to-Sleep Control Input Delay VID_CT Charging Current IVID_CT VVID_CT = 0V CONTROL I/O (S3, S5, FAULT) S3, S5 Internal Pull-up Impedance to 5VSB FAULT Output Impedance FAULT = high TEMPERATURE MONITOR Fault-Level Threshold (Note 4) Shutdown-Level Threshold (Note 4) NOTES: 3. Guaranteed by Correlation. 4. Guaranteed by Design. FN9062 Rev 2.00 Apr 13, 2004 Page 6 of 17 ISL6504, ISL6504A Functional Pin Description (SOIC pinout) 3V3 (Pin 5) Connect this pin to the ATX 3.3V output. This pin provides the output current for the 1V2VID pin, and is monitored for power quality. 5VSB (Pin 16) Provide a very well de-coupled 5V bias supply for the IC to this pin by connecting it to the ATX 5VSB output. This pin provides all the chip’s bias as well as the base current for Q2 (see typical application diagram). The voltage at this pin is monitored for power-on reset (POR) purposes. GND (Pin 8) Signal ground for the IC. All voltage levels are measured with respect to this pin. S3 and S5 (Pins 6 and 7) These pins switch the IC’s operating state from active (S0, S1/S2) to S3 and S4/S5 sleep states. These are digital inputs featuring internal 50k (typical) resistor pull-ups to 5VSB. Internal circuitry de-glitches these pins for disturbances lasting as long as 2s (typically). Additional circuitry blocks any illegal state transitions (such as S3 to S4/S5 or vice versa). Respectively, connect S3 and S5 to the computer system’s SLP_S3 and SLP_S5 signals. FAULT (Pin 9) DLA (Pin 10) This pin is an open-collector output. Connect a 1k resistor from this pin to the ATX 12V output. This resistor is used to pull the gates of suitable N-MOSFETs to 12V, which in active state, switch in the ATX 3.3V and 5V outputs into the 3.3VDUAL/3.3VSB and 5VDUAL outputs, respectively. 5VDL (Pin 12) Connect this pin to the 5VDUAL output (VOUT4). In either operating state (when on), the voltage at this pin is provided through a fully-on MOS transistor. This pin is also monitored for undervoltage events. 5VDLSB (Pin 11) Connect this pin to the gate of a suitable P-MOSFET or bipolar PNP. ISL6504: In S3 sleep state, this transistor is switched on, connecting the ATX 5VSB output to the 5VDUAL regulator output. ISL6504A: In S3 and S4/S5 sleep state, this transistor is switched on, connecting the ATX 5VSB output to the 5VDUAL regulator output. 1V5SB (Pin 1) This pin is the output of the internal 1.5V regulator (VOUT1). This internal regulator operates for as long as 5VSB is applied to the IC and draws its output current from the 3V3DL pin. This pin is monitored for undervoltage events. 1V2VID (Pin 4) In case of an undervoltage on any of the controlled outputs, on any of the monitored ATX voltages, or in case of an overtemperature event, this pin is used to report the fault condition by being pulled to 5VSB. Connect a 1k resistor from this pin to GND. This pin is the output of the internal 1.2V voltage identification (VID) regulator (VOUT2). This internal regulator operates only in active states (S0, S1/S2) and is shut off during any sleep state. This regulator draws its output current from the 3V3 pin. This pin is monitored for undervoltage events. SS (Pin 13) VID_PG (Pin 14) Connect this pin to a small ceramic capacitor (no less than 5nF; 0.1F recommended). The internal soft-start (SS) current source along with the external capacitor creates a voltage ramp used to control the ramp-up of the output voltages. Pulling this pin low with an open-drain device shuts down all the outputs as well as force the FAULT pin low. The CSS capacitor is also used to provide a controlled voltage slew rate during active-to-sleep transitions on the 3.3VDUAL/3.3VSB output. 3V3DL (Pin 3) Connect this pin to the 3.3V dual/stand-by output (VOUT3). In sleep states, the voltage at this pin is regulated to 3.3V; in active states, ATX 3.3V output is delivered to this node through a fully-on N-MOS transistor. During all operating states, this pin is monitored for undervoltage events. This pin provides all the output current delivered by the 1V5SB pin. 3V3DLSB (Pin 2) Connect this pin to the base of a suitable NPN transistor. In sleep state, this transistor is used to regulate the voltage at the 3V3DL pin to 3.3V. FN9062 Rev 2.00 Apr 13, 2004 This pin is the open collector output of the 1V2VID power good comparator. Connect a 10kpull-up resistor from this pin to the 1V2VID output. As long as the 1V2VID output is below its UV threshold, this pin is pulled low. VID_CT (Pin 15) Connect a small capacitor from this pin to ground. The capacitor is used to delay the VID_PG reporting the 1V2VID has reached power good limits. Description Operation The ISL6504/A controls 4 output voltages (Refer to Figures 1, 2, and 3). It is designed for microprocessor computer applications with 3.3V, 5V, 5VSB, and 12V bias input from an ATX power supply. The IC is composed of three linear controllers/regulators supplying the computer system’s 1.5VSB (VOUT1), 3.3VSB and PCI slots’ 3.3VAUX power (VOUT3), the 1.2V VID circuitry power (VOUT2), a dual switch controller supplying the 5VDUAL voltage (VOUT4), as Page 7 of 17 ISL6504, ISL6504A well as all the control and monitoring functions necessary for complete ACPI implementation. Initialization The ISL6504/A automatically initializes upon receipt of input power. The Power-On Reset (POR) function continually monitors the 5VSB input supply voltage, initiating 3.3VDUAL/3.3VSB and 1.5VSB soft-start operation shortly after exceeding POR threshold. Dual Outputs Operational Truth Table Table 1 describes the truth combinations pertaining to the 3.3VDUAL/SB and 5VDUAL outputs. The last two lines highlight the only difference between the ISL6504 and ISL6504A. The internal circuitry does not allow the transition from an S3 (suspend to RAM) state to an S4/S5 (suspend to disk/soft off) state or vice versa. The only ‘legal’ transitions are from an active state (S0, S1) to a sleep state (S3, S5) and vice versa. 5VSB S3 S5 3.3V, 5V 3V3DLSB DLA 3V3DL 5VDLSB 5VDL FIGURE 4. 5VDUAL AND 3.3VDUAL/3.3VSB TIMING DIAGRAM; ISL6504 TABLE 1. 5VDUAL OUTPUT (VOUT4) TRUTH TABLE S5 S3 3.3VDL/SB 5VDL COMMENTS 1 1 3.3V 5V S0/S1/S2 States (Active) 1 0 3.3V 5V S3 0 1 0 0 3.3V 0V S4/S5 (ISL6504) 0 0 3.3V 5V S4/S5 (ISL6504A) Note 5VSB S3 Maintains Previous State NOTE: Combination Not Allowed. Functional Timing Diagrams Figures 4 (ISL6504), 5 (ISL6504A), and 6 are timing diagrams, detailing the power up/down sequences of all the outputs in response to the status of the sleep-state pins (S3, S5), as well as the status of the input ATX supply. Not shown in these diagrams is the deglitching feature used to protect against false sleep state tripping. Both S3 and S5 pins are protected against noise by a 2s filter (typically 1–4s). This feature is useful in noisy computer environments if the control signals have to travel over significant distances. Additionally, the S3 pin features a 200s delay in transitioning to sleep states. Once the S3 pin goes low, an internal timer is activated. At the end of the 200s interval, if the S5 pin is low, the ISL6504/A switches into S5 sleep state; if the S5 pin is high, the ISL6504/A goes into S3 sleep state. S5 3.3V, 5V 3V3DLSB DLA 3V3DL 5VDLSB 5VDL FIGURE 5. 5VDUAL AND 3.3VDUAL/3.3VSB TIMING DIAGRAM; ISL6504A 5VSB S3 S5 3.3V, 5V, 12V DLA 1V5SB 1V2VID FIGURE 6. 1.5VSB, AND 1.2VVID TIMING DIAGRAM FN9062 Rev 2.00 Apr 13, 2004 Page 8 of 17 ISL6504, ISL6504A Soft-Start into Sleep States (S3, S4/S5) The 5VSB POR function initiates the soft-start sequence. An internal 10A current source charges an external capacitor. The error amplifiers reference inputs are clamped to a level proportional to the SS (soft-start) pin voltage. As the SS pin voltage slews from about 1.25V to 2.5V, the input clamp allows a rapid and controlled output voltage rise. Figures 7 (ISL6504) and 8 (ISL6504A) show the soft-start sequence for the typical application start-up into a sleep state. At time T0 5VSB (bias) is applied to the circuit. At time T1, the 5VSB surpasses POR level. An internal fast charge circuit quickly raises the SS capacitor voltage to approximately 1V, then the 10A current source continues the charging. 5VSB (1V/DIV) SOFT-START (1V/DIV) 0V VOUT4 (5VDUAL) VOUT3 (3.3VDUAL/3.3VSB) OUTPUT VOLTAGES (1V/DIV) VOUT1 (1.5VSB) VOUT2 (1.2VVID) 0V 5VSB (1V/DIV) T0 SOFT-START (1V/DIV) T1 T2 T4 T3 T5 TIME FIGURE 8. SOFT-START INTERVAL IN A SLEEP STATE; ISL6054A 0V VOUT4 (5VDUAL) IF S3 VOUT3 (3.3VDUAL/3.3VSB) OUTPUT VOLTAGES (1V/DIV) VOUT1 (1.5VSB) VOUT2 (1.2VVID) 0V VOUT4 (5VDUAL) if S5 T0 T1 T2 T3 T4 T5 TIME FIGURE 7. SOFT-START INTERVAL IN A SLEEP STATE; ISL6504 The soft-start capacitor voltage reaches approximately 1.25V at time T2, at which point the 3.3VDUAL/3.3VSB and 1.5VSB error amplifiers’ reference inputs start their transition, resulting in the output voltages ramping up proportionally. The ramp-up continues until time T3 when the two voltages reach the set value. As the soft-start capacitor voltage reaches approximately 2.75V, the undervoltage monitoring circuit of this output is activated and the soft-start capacitor is quickly discharged to approximately 1.25V. Following the 3ms (typical) time-out between T3 and T4, the soft-start capacitor commences a second ramp-up designed to smoothly bring up the remainder of the voltages required by the system. At time T5, voltages are within regulation limits, and as the SS voltage reaches 2.75V, all the remaining UV monitors are activated and the SS capacitor is quickly discharged to 1.25V, where it remains until the next transition. As the 1.2VVID output is only active while in an active state, it does not come up, but rather waits until the main ATX outputs come up within regulation limits. Soft-Start into Active States (S0, S1) If both S3 and S5 are logic high at the time the 5VSB is applied, the ISL6504/A will assume active state wake-up and keep off the required outputs until some time (typically 25ms) after the monitored main ATX output (3.3V) exceeds the set threshold. This time-out feature is necessary in order to ensure the main ATX outputs are stabilized. The time-out also assures smooth transitions from sleep into active when sleep states are being supported. 3.3VDUAL/3.3VSB and 1.5VSB outputs will come up right after bias voltage surpasses POR level. FN9062 Rev 2.00 Apr 13, 2004 Page 9 of 17 ISL6504, ISL6504A the maximum current rating of an integrated regulator (output with pass regulator on chip) can lead to output voltage drooping; if excessive, this droop can ultimately trip the undervoltage detector and send a FAULT signal to the computer system. +12VIN DLA PIN (2V/DIV) INPUT VOLTAGES (2V/DIV) +5VIN +5VSB +3.3VIN SOFT-START (1V/DIV) 0V OUTPUT VOLTAGES (1V/DIV) VOUT4 (5VDUAL) VOUT3 (3.3VDUAL/3.3VSB) VOUT1 (1.5VSB) VOUT2 (1.2VVID) 0V T0 T1 T2 T3 TIME FIGURE 9. SOFT-START INTERVAL IN ACTIVE STATE During sleep-to-active state transitions from conditions where the 5VDUAL output is initially 0V (such as S5 to S0 transition, or simple power-up sequence directly into active state), the circuit goes through a quasi soft-start, the 5VDUAL output being pulled high through the body diode of the N-Channel MOSFET connected between it and the 5V ATX. Figure 9 exemplifies this start-up case. 5VSB is already present when the main ATX outputs are turned on, at time T0. As a result of +5VIN ramping up, the 5VDUAL output capacitors charge up through the body diode of Q4 (see Typical Application). At time T1, all main ATX outputs exceed the ISL6504/A’s undervoltage thresholds, and the internal 25ms (typical) timer is initiated. At T2, the time-out initiates a soft-start, and the 1.2V voltage ID output is ramped-up, reaching regulation limits at time T3. Simultaneous with the beginning of this ramp-up, at time T2, the DLA pin is released, allowing the pull-up resistor to turn on Q2 and Q4, and bring the 5VDUAL output in regulation. Shortly after time T3, as the SS voltage reaches 2.75V, the soft-start capacitor is quickly discharged down to approximately 2.45V, where it remains until a valid sleep state request is received from the system. A FAULT condition occurring on an output when controlled through an external pass transistor will only set off the FAULT flag, and it will not shut off or latch off any part of the circuit. A FAULT condition occurring on an output controlled through an internal pass transistor, will set off the FAULT flag, and it will shut off the respective faulting regulator only. If shutdown or latch off of the entire circuit is desired in case of a fault, regardless of the cause, this can be achieved by externally pulling or latching the SS pin low. Pulling the SS pin low will also force the FAULT pin to go low and reset any internally latched-off output. Special consideration is given to the initial start-up sequence. If, following a 5VSB POR event, any of the 1.5VSB or 3.3VDUAL/3.3VSB outputs is ramped up and is subject to an undervoltage event before the end of the second soft-start ramp, then the FAULT output goes high and the entire IC latches off. Latch-off condition can be reset by cycling the bias power (5VSB). Undervoltage events on the 1.5VSB and the 3.3VDUAL/3.3VSB outputs at any other times are handled according to the description found in the second paragraph under the current heading. Another condition that could set off the FAULT flag is chip overtemperature. If the ISL6504/A reaches an internal temperature of 140oC (typical), the FAULT flag is set, but the chip continues to operate until the temperature reaches 155oC (typical), when unconditional shutdown of all outputs takes place. Operation resumes only after powering down the IC (to create a 5VSB POR event) and a start-up (assuming the cause of the fault has been removed; if not, as it heats up again, it will repeat the FAULT cycle). In ISL6504/A applications, loss of the active ATX output (3.3VIN; as detected by the on-board voltage monitor) during active state operation causes the chip to switch to S5 sleep state, in addition to reporting the input UV condition on the FAULT pin. Exiting from this forced S5 state can only be achieved by returning the faulting input voltage above its UV threshold, by resetting the chip through removal of 5VSB bias voltage, or by bringing the SS pin at a potential lower than 0.8V. Application Guidelines Fault Protection Soft-Start Interval All the outputs are monitored against undervoltage events. A severe overcurrent caused by a failed load on any of the outputs, would, in turn, cause that specific output to suddenly drop. If any of the output voltages drops below 80% (typical) of their set value, such event is reported by having the FAULT pin pulled to 5V. Additionally, exceeding The 5VSB output of a typical ATX supply is capable of 725mA, with newer models rated for 1.0A, and even 2.0A. During power-up in a sleep state, the 5VSB ATX output needs to provide sufficient current to charge up all the applicable output capacitors and, simultaneously, provide some amount of current to the output loads. Drawing FN9062 Rev 2.00 Apr 13, 2004 Page 10 of 17 ISL6504, ISL6504A excessive amounts of current from the 5VSB output of the ATX can lead to voltage collapse and induce a pattern of consecutive restarts with unknown effects on the system’s behavior or health. I SS I COUT = ------------------------------ C OUT V OUT , where C SS V BG ISS - soft-start current (typically 10A) CSS - soft-start capacitor VBG - bandgap voltage (typically 1.26V) COUT x VOUT) - sum of the products between the capacitance and the voltage of an output (total charge delivered to all outputs) Due to the various system timing events and their interaction, it is recommended that the soft-start interval not be set to exceed 30ms. For most applications, a 0.1F capacitor is recommended. Shutdown In case of a FAULT condition that might endanger the computer system, or at any other time, all the ISL6504/A outputs can be shut down by pulling the SS pin below the specified shutdown level (typically 0.8V) with an open drain or open collector device capable of sinking a minimum of 2mA. Pulling the SS pin low effectively shuts down all the pass elements. Upon release of the SS pin, the ISL6504 undergoes a new soft-start cycle and resumes normal operation in accordance to the ATX supply and control pins status. VID_PG Delay During power-up and initial soft-start, the VID_PG and VID_CT pins are held low. As the 1V2VID output exceeds its rising power-good threshold, the capacitor connected at the VID_CT pin starts to charge up through the internal 10A current source. As the voltage on this capacitor exceeds 1.25V, the open-collector VID_PG pin is released and VID POWER GOOD status is thus reported. The value of the VID_CT capacitor to be used to obtain a given VID_PG delay can be determined from the graph in Figure 10. For extended delays exceeding the range of the graph, use the following formula: t DELAY C = ------------------125000 , where tDELAY - desired delay time (s) C - VID_CT capacitor to obtain desired delay time (F) FN9062 Rev 2.00 Apr 13, 2004 70 60 50 C (nF) The built-in soft-start circuitry allows tight control of the slewup speed of the output voltages controlled by the ISL6504, thus enabling power-ups free of supply drop-off events. Since the outputs are ramped up in a linear fashion, the current dedicated to charging the output capacitors can be calculated with the following formula: 80 40 30 20 10 0 0 1 2 3 4 5 6 7 8 9 10 VID_PG Delay (ms) FIGURE 10. VID_PG DELAY DEPENDENCE ON VID_CT CAPACITOR Layout Considerations The typical application employing an ISL6504/A is a fairly straight forward implementation. Like with any other linear regulator, attention has to be paid to the few potentially sensitive small signal components, such as those connected to sensitive nodes or those supplying critical bypass current. The power components (pass transistors) and the controller IC should be placed first. The controller should be placed in a central position on the motherboard, closer to the memory controller chip and processor, but not excessively far from the 3.3VDUAL island or the I/O circuitry. Ensure the 1V5SB, 1V2VID, 3V3, and 3V3DL connections are properly sized to carry 100mA without exhibiting significant resistive losses at the load end. Similarly, the input bias supply (5VSB) can carry a significant level of current - for best results, ensure it is connected to its respective source through an adequately sized trace. The pass transistors should be placed on pads capable of heatsinking matching the device’s power dissipation. Where applicable, multiple via connections to a large internal plane can significantly lower localized device temperature rise. Placement of the decoupling and bulk capacitors should follow a placement reflecting their purpose. As such, the high-frequency decoupling capacitors should be placed as close as possible to the load they are decoupling; the ones decoupling the controller close to the controller pins, the ones decoupling the load close to the load connector or the load itself (if embedded). Even though bulk capacitance (aluminum electrolytics or tantalum capacitors) placement is not as critical as the high-frequency capacitor placement, having these capacitors close to the load they serve is preferable. The critical small signal components include the soft-start capacitor, CSS, as well as all the high-frequency decoupling capacitors. Locate these components close to the respective Page 11 of 17 ISL6504, ISL6504A pins of the control IC, and connect them to ground through a via placed close to the ground pad. Minimize any leakage current paths from the SS node, as the internal current source is only 10A (typical). Also, during the transition between active and sleep states on the 3.3VDUAL/3.3VSB and 5VDUAL outputs, there is a short interval of time during which none of the power pass elements are conducting - during this time the output capacitors have to supply all the output current. The output voltage drop during this brief period of time can be easily approximated with the following formula: +12VIN +5VSB CIN C5VSB 5VSB SS CSS 1V5SB CBULK4 LOAD VOUT1 3V3DLSB CHF3 Q4 DLA VOUT3 3V3DL CBULK3 LOAD CHF4 LOAD CBULK1 Q1 VOUT4 5VDL +5VIN 3V3 CBULK2 VOUT2 GND CHF2 +3.3VIN KEY ISLAND ON POWER PLANE LAYER ISLAND ON CIRCUIT/POWER PLANE LAYER VIA CONNECTION TO GROUND PLANE FIGURE 11. PRINTED CIRCUIT BOARD ISLANDS A multi-layer printed circuit board is recommended. Figure 11 shows the connections to most of the components in the circuit. Note that the individual capacitors shown each could represent numerous physical capacitors. Dedicate one solid layer for a ground plane and make all critical component ground connections through vias placed as close to the component terminal as possible. Dedicate another solid layer as a power plane and break this plane into smaller islands of common voltage levels. Ideally, the power plane should support both the input power and output power nodes. Use copper filled polygons on the top and bottom circuit layers to create power islands connecting the filtering components (output capacitors) and the loads. Use the remaining printed circuit layers for small signal wiring. Component Selection Guidelines Output Capacitors Selection The output capacitors should be selected to allow the output voltage to meet the dynamic regulation requirements of active state operation (S0, S1). The load transient for the various microprocessor system’s components may require FN9062 Rev 2.00 Apr 13, 2004 VOUT - output voltage drop IOUT - output current during transition COUT - output capacitor bank capacitance ISL6504/A 1V2VID Q2 tt V OUT = I OUT ESR OUT + --------------- , where C OUT ESROUT - output capacitor bank ESR LOAD CHF1 Q3 5VDLSB high quality capacitors to supply the high slew rate (di/dt) current demands. Thus, it is recommended that the output capacitors be selected for transient load regulation, paying attention to their parasitic components (ESR, ESL). tt - active-to-sleep or sleep-to-active transition time (10s typ.) The output voltage drop is heavily dependent on the ESR (equivalent series resistance) of the output capacitor bank, the choice of capacitors should be such as to maintain the output voltage above the lowest allowable regulation level. Input Capacitors Selection The input capacitors for an ISL6504/A application must have a sufficiently low ESR so as not to allow the input voltage to dip excessively when energy is transferred to the output capacitors. If the ATX supply does not meet the specifications, certain imbalances between the ATX’s outputs and the ISL6504/A’s regulation levels could have as a result a brisk transfer of energy from the input capacitors to the supplied outputs. At the transition between active and sleep states, such phenomena could be responsible for the 5VSB voltage drooping excessively and affecting the output regulation. The solution to such a potential problem is using larger input capacitors with a lower total combined ESR. Transistor Selection/Considerations The ISL6504/A usually requires one P-Channel (or bipolar PNP), two N-Channel MOSFETs, and one bipolar NPN transistors. One important criteria for selection of transistors for all the linear regulators/switching elements is package selection for efficient removal of heat. The power dissipated in a linear regulator or an ON/OFF switching element is P LINEAR = I O V IN – V OUT Select a package and heatsink that maintains the junction temperature below the rating with the maximum expected ambient temperature. Page 12 of 17 ISL6504, ISL6504A Q1 Q3 The NPN transistor used as sleep state pass element on the 3.3VDUAL output has to have a minimum current gain of 100 at 1.5V VCE and 650mA ICE throughout the in-circuit operating temperature range. For larger current ratings on the 3.3VDUAL output (providing the ATX 5VSB output rating is equally extended), selection criteria for Q1 include an appropriate current gain (hfe) and saturation characteristics. If a P-Channel MOSFET is used to switch the 5VSB output of the ATX supply into the 5VDUAL output during sleep states, then the selection criteria of this device is proper voltage budgeting. The maximum rDS(ON) , however, has to be achieved with only 4.5V of gate-to-source voltage, so a logic level MOSFET needs to be selected. If a PNP device is chosen to perform this function, it has to have a low- saturation voltage while providing the maximum sleep current and have a current gain sufficiently high to be saturated using the minimum drive current (typically 20mA). Q2, Q4 These N-Channel MOSFETs are used to switch the 3.3V and 5V inputs provided by the ATX supply into the 3.3VDUAL/3.3VSB and 5VDUAL outputs while in active (S0, S1) state. The main criteria for the selection of these transistors is output voltage budgeting. The maximum rDS(ON) allowed at highest junction temperature can be expressed with the following equation: V INmin – V OUTmin r DS ON max = -------------------------------------------------- , where I OUTmax VINmin - minimum input voltage VOUTmin - minimum output voltage allowed IOUTmax - maximum output current FN9062 Rev 2.00 Apr 13, 2004 Page 13 of 17 ISL6504, ISL6504A ISL6504 Application Circuit a PNP transistor, such as an MMBT2907AL. For additional, more detailed information on the circuit, including a Bill-ofMaterials and circuit board description, see Application Note AN1001. Also see Intersil Corporation’s web page (www.intersil.com). Figure 12 shows a typical application circuit for the ISL6504/A. The circuit provides the 3.3VDUAL/3.3VSB voltage, the ICH4 resume well 1.5VSB voltage, the 1.2VVID voltage identification output, and the 5VDUAL keyboard/mouse voltage from +3.3V, +5VSB, +5V, and +12VDC ATX supply outputs. Q3 can also be +5VIN R1 +12VIN 1k +3.3VIN +5VSB C1 1mF 5VSB 16 3V3 5 14 15 Q2 HUF76113T3S +3.3VDUAL/3.3VSB + 3V3DLSB 2 Q1 2SD1802 3V3DL 4 3 C4 330mF VID_PG ‘VID PGOOD’ VID_CT C2 0.1mF R2 10k +1.2VVID 1V2VID C3 + 10mF U1 ISL6504/A ‘FAULT’ FAULT +1.5VSB 1V5SB + C5 10mF 9 11 10 S3 S5 S5 SS C7 0.1mF Q3 FDV304P 1 R3 1k S3 5VDLSB 6 12 +5VDUAL 5VDL + 7 13 Q4 HUF76113T3S DLA C6 220mF 8 GND FIGURE 12. TYPICAL ISL6504/A APPLICATION DIAGRAM © Copyright Intersil Americas LLC 2002-2004. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN9062 Rev 2.00 Apr 13, 2004 Page 14 of 17 ISL6504, ISL6504A Small Outline Plastic Packages (SOIC) M16.3 (JEDEC MS-013-AA ISSUE C) N 16 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE INDEX AREA 0.25(0.010) M H B M INCHES E -B- 1 2 3 L SEATING PLANE -A- h x 45o A D -C- e A1 B 0.25(0.010) M C 0.10(0.004) C A M SYMBOL MIN MAX MIN MAX NOTES A 0.0926 0.1043 2.35 2.65 - A1 0.0040 0.0118 0.10 0.30 - B 0.013 0.0200 0.33 0.51 9 C 0.0091 0.0125 0.23 0.32 - D 0.3977 0.4133 10.10 10.50 3 E 0.2914 0.2992 7.40 7.60 4 e µ B S NOTES: 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. MILLIMETERS 0.050 BSC 1.27 BSC - H 0.394 0.419 10.00 10.65 - h 0.010 0.029 0.25 0.75 5 L 0.016 0.050 0.40 1.27 6 N 16 0o 16 8o 0o 7 8o Rev. 0 12/93 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch) 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. FN9062 Rev 2.00 Apr 13, 2004 Page 15 of 17 ISL6504, ISL6504A Quad Flat No-Lead Plastic Package (QFN) Micro Lead Frame Plastic Package (MLFP) L20.6x6 20 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE (COMPLIANT TO JEDEC MO-220VJJB ISSUE C) MILLIMETERS SYMBOL MIN NOMINAL MAX NOTES A 0.80 0.90 1.00 - A1 - - 0.05 - A2 - - 1.00 A3 b 0.28 D 0.33 9 0.40 5, 8 6.00 BSC D1 D2 9 0.20 REF - 5.75 BSC 3.55 3.70 9 3.85 7, 8 E 6.00 BSC - E1 5.75 BSC 9 E2 3.55 e 3.70 3.85 7, 8 0.80 BSC - k 0.25 - - - L 0.35 0.60 0.75 8 L1 - - 0.15 10 N 20 2 Nd 5 3 Ne 5 3 P - - 0.60 9 - - 12 9 Rev. 1 10/02 NOTES: 1. Dimensioning and tolerancing conform to ASME Y14.5-1994. 2. N is the number of terminals. 3. Nd and Ne refer to the number of terminals on each D and E. 4. All dimensions are in millimeters. Angles are in degrees. 5. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. 7. Dimensions D2 and E2 are for the exposed pads which provide improved electrical and thermal performance. 8. Nominal dimensions are provided to assist with PCB Land Pattern Design efforts, see Intersil Technical Brief TB389. 9. Features and dimensions A2, A3, D1, E1, P & are present when Anvil singulation method is used and not present for saw singulation. 10. Depending on the method of lead termination at the edge of the package, a maximum 0.15mm pull back (L1) maybe present. L minus L1 to be equal to or greater than 0.3mm. FN9062 Rev 2.00 Apr 13, 2004 Page 16 of 17 ISL6504, ISL6504A M16.15 (JEDEC MS-012-AC ISSUE C) 16 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE Small Outline Plastic Packages (SOIC) N INCHES INDEX AREA H 0.25(0.010) M B M SYMBOL E -B- 1 2 3 L SEATING PLANE -A- h x 45o A D -C- e B 0.25(0.010) M C 0.10(0.004) C A M B S MILLIMETERS MAX MIN MAX NOTES A 0.053 0.069 1.35 1.75 - A1 0.004 0.010 0.10 0.25 - B 0.014 0.019 0.35 0.49 9 C 0.007 0.010 0.19 0.25 - D 0.386 0.394 9.80 10.00 3 E 0.150 0.157 3.80 4.00 4 e µ A1 MIN 0.050 BSC 1.27 BSC - H 0.228 0.244 5.80 6.20 - h 0.010 0.020 0.25 0.50 5 L 0.016 0.050 0.40 1.27 6 8o 0o N 16 0o 16 7 8o Rev. 1 02/02 NOTES: 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch) 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. FN9062 Rev 2.00 Apr 13, 2004 Page 17 of 17