TI CD74FCT533M Fct interface logic octal transparent latch, three-state Datasheet

CD54/74FCT373,
CD54/74FCT373AT,
CD54/74FCT533
Data sheet acquired from Harris Semiconductor
SCHS272
FCT Interface Logic
Octal Transparent Latch, Three-State
February 1996
Features
Description
• CD54/74FCT373, CD54/74FCT373AT - Non-Inverting
The CD54/74FCT373, 373AT, and 533 octal transparent
latches use a small-geometry BiCMOS technology. The output
stage is a combination of bipolar and CMOS transistors that
limits the output-HIGH level to two diode drops below VCC. This
resultant lowering of output swing (0V to 3.7V) reduces power
bus ringing (a source of EMI) and minimizes VCC bounce and
ground bounce and their effects during simultaneous output
switching. The output configuration also enhances switching
speed and is capable of sinking 32mA to 48mA.
• CD54/74FCT533 - Inverting
• Buffered inputs
• Typical Propagation Delay: 3.9ns at VCC = 5V,
TA = +25oC, CL = 50pF (FCT373AT)
• SCR-Latchup-Resistant BiCMOS Process and Circuit
Design
The CD54/74FCT373, 373AT, and 533 outputs are transparent to the inputs when the Latch Enable (LE) is HIGH. When
the Latch Enable (LE) goes LOW, the data is latched. The
Output Enable (OE) controls the three-state outputs. When
the Output Enable (OE) is HIGH, the outputs are in the highimpedance state. The latch operation is independent of the
state of the Output Enable.
• FCTXXX Types - Speed of Bipolar FAST®/AS/S;
FCTXXXAT Types - 30% Faster than FAST/AS/S with
Significantly Reduced Power Consumption
• 48mA to 32mA Output Sink Current (Commercial/
Extended Industrial)
• Output Voltage Swing Limited to 3.7V at VCC = 5V
Ordering Information
• Controlled Output-Edge Rates
PART NUMBER
TEMP. RANGE (oC)
PACKAGE
• Input/Output Isolation to VCC
CD54/74FCT373E
-55 to 125, 0 to 70
20 Ld PDIP
• BiCMOS Technology with Low Quiescent Power
CD54/74FCT373ATE
-55 to 125, 0 to 70
20 Ld PDIP
CD54/74FCT533E
-55 to 125, 0 to 70
20 Ld PDIP
CD54/74FCT373M
-55 to 125, 0 to 70
20 Ld SOIC
CD54/74FCT373ATM
-55 to 125, 0 to 70
20 Ld SOIC
CD54/74FCT533M
-55 to 125, 0 to 70
20 Ld SOIC
CD54/74FCT373SM
-55 to 125, 0 to 70
20 Ld SSOP
CD54/74FCT533SM
-55 to 125, 0 to 70
20 Ld SSOP
CD54FCT373H
-55 to 125
CD54FCT533H
-55 to 125
Functional Diagram
TRUTH TABLE
D0
D1
D2
D3
D4
D5
D6
D7
3
4
7
8
13
14
17
18
2
5
6
9
12
15
16
19
11
373
533
Q0
Q1
Q2
Q3
Q4
Q5
Q6
Q7
Q0
Q1
Q2
Q3
Q4
Q5
Q6
Q7
1
LE
OUTPUT
ENABLE
LATCH
ENABLE
DATA
373, 373AT
OUTPUT
L
H
H
H
L
L
H
L
L
H
L
L
I
L
H
L
L
h
H
L
H
X
X
Z
Z
H = HIGH voltage level.
L = LOW voltage level.
X = Irrelevant.
Z = HIGH Impedance.
OE
533
OUTPUT
I = LOW voltage level one setup time
prior to the high-to-low latch enable
transition.
h = HIGH voltage level one setup time
prior to the high-to-low latch enable
transition.
FAST® is a registered trademark of Fairchild Semiconductor Corporation.
CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures.
Copyright
© Harris Corporation 1996
1
File Number
2230.2
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright  1999, Texas Instruments Incorporated
Similar pages