CHEMI-CON APSF160EC3101 Conductive polymer aluminum solid capacitor Datasheet

CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
TM
NPCAP
Radial Lead
PSF
-
Series
PSF
・Super low ESR, high ripple current capability
・ESR 5mΩmax. (2 to 4Vdc)
・Longer life (20,000 hours at 105℃)
・Rated voltage range : 2 to 16Vdc
・Solvent resistant type (see PRECAUTIONS AND GUIDELINES)
・RoHS Compliant
・Halogen Free
Lower ESR
PSE P56
◆SPECIFICATIONS
Items
Characteristics
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
*Note
-55 to +105℃
2 to 16Vdc
±20%(M)
Rated voltage(V)×1.15
Shall not exceed values shown in STANDARD RATINGS.
(at 20℃, 120Hz)
(at 105℃)
(at 20℃ after 2 minutes)
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
(Max.Impedance Ratio)
Endurance
0.10 max.
(at 20℃, 120Hz)
Z(-25℃)/Z(+20℃)≦1.15
Z(-55℃)/Z(+20℃)≦1.25
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 20,000 hours
at 105℃.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
ESR
≦150% of the initial specified value
Leakage current
≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to DC voltage at 60℃,
90 to 95% RH for 1,000 hours.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦The initial specified value
ESR
2 to 6.3Vdc : ≦The initial specified value
16Vdc
: ≦150% of the initial specified value
Leakage current
≦The initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds
through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦The initial specified value
ESR
2 to 6.3Vdc : ≦The initial specified value
16Vdc
: ≦150% of the initial specified value
Leakage current
≦The initial specified value
0.5% per 1,000 hours maximum (Confidence level 60% at 105℃)
Bias Humidity Test
Surge Voltage Test
Failure Rate
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃.
◆DIMENSIONS [mm]
Code : E
Coated Case
Size code F05
H08
HB5
JB5
F08
FA5
φD
8.0
10.0
6.3
φd
0.6
0.45
0.6
0.5
F
3.5
5.0
2.5
φD'
φD+0.5max.
L'
L+1.0max. (Note1) L+0.3max. L+1.0max. L+1.5max.
φD'
φd
F05, F08, H08
F±0.5
● Terminal
Note1 : L+1.2 max. for 6.3V820µF
4min.
F±0.5
Coated Case
φD'
φd
FA5, HB5, JB5
15min.
F±0.5
L'
(FA5)
L'
15min.
(HB5, JB5)
◆MARKING
EX) 2.5V560µF
F 6D6
560
2.5V
4min.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
54
CAT. No. E1001Q
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
TM
NPCAP
Radial Lead
PSFSeries
-
◆PART NUMBERING SYSTEM
1
2
3
4
5
6
7
8
9
10
11 12
13
14
15 16
17
18
A PS F 2 R 5 E AA 5 6 1 M F 0 8 S
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 560µF:561)
Lead forming·Taping code
Terminal code
Voltage code (ex. 2.5V:2R5, 16V:160)
Series code
Category
Please refer to "Product code guide (conductive polymer type)"
◆STANDARD RATINGS
WV
(Vdc)
2
2.5
4
6.3
16
Cap
(µF)
1,000
330
470
560
820
1,200
1,600
470
560
820
100
100
270
270
330
470
470
Case size
φD×L(mm)
Leakage current
(µA max./after 2min.)
ESR
(mΩ max./20℃,
100k to 300kHz)
Rated ripple current
(mArms/105℃, 100kHz)
6.3×8
6.3×8
6.3×8
6.3×8
6.3×8
6.3× 8
8×8
6.3× 8
6.3× 8
6.3×8
6.3× 5
6.3× 10.5
8×8
8×11.5
8×8
8×11.5
10× 11.5
500
500
500
500
500
1,200
800
500
500
1,030
500
500
864
864
1,050
1,500
1,500
5
5
5
5
5
5
5
5
5
8
24
25
10
11
13
11
10
5,900
5,900
5,900
5,900
5,900
5,900
6,100
5,900
5,900
4,700
2,490
2,820
5,000
5,080
4,700
5,400
6,100
Part No.
APSF2R0E□□102MF08S
APSF2R5E□□331MF08S
APSF2R5E□□471MF08S
APSF2R5E□□561MF08S
APSF2R5E□□821MF08S
APSF2R5E□□122MF08S
APSF2R5E□□162MH08S
APSF4R0E□□471MF08S
APSF4R0E□□561MF08S
APSF6R3E□□821MF08S
APSF160E□□101MF05S
APSF160E□□101MFA5S
APSF160E□□271MH08S
APSF160E□□271MHB5S
APSF160E□□331MH08S
APSF160E□□471MHB5S
APSF160E□□471MJB5S
□□ : Enter the appropriate lead forming or taping code.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
55
CAT. No. E1001Q
Similar pages