JEWEL HILL ELECTRONIC CO.,LTD. JEWEL HILL ELECTRONIC CO.,LTD. SPECIFICATIONS FOR LCD MODULE Module No. JH30240400B E-mail: [email protected] JH30240400B VER: 0.1 Website: www.jhlcd.com -0- Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. TABLE OF CONTENTS LCM NUMBER SYSTEM 1.GENERAL SPECIFICATIONS…………………………………………...3 2.OUTLINE DRAW…………………………………………………………….4 3.ABSOLUTE MAXIMUM RATINGS……………………………………….5 4.ELECTRICAL SPECIFICATIONS………………………………………...6 5.OPTICAL CHARACTERISTICS………………………………………….12 6.RELIABILITY………………………………………………………………16 7.QUALITY LEVEL………………………………………………………….17 8.PRECAUTIONS FOR USE OF LCD MODULES………………………..21 9.REVISION HISTORY……………………………………………………...24 SAMPLE APPROVED REPORT…………………………………………… JH30240400B VER: 0.1 -1- Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. LCM Number System JH 30 240400 B T N F M N T F L W N -V00- SC SPECIAL CODE: P: PIN;C:CONNECT;O: OTHER;........ VERSION NUMBER: V00～V99 IC CONTROLLER: C:WITH CONTROLLER; N:WITHOUT CONTROLLER; BACKLIGHT COLOR: W:WHITE; O:OTHER; BACKLIGHT MODE: L:LED; E:EL; C:CCFL; CONNECTOR: H:HEATSEAL; Z:ZEBRA; F:FPC O:OTHER; POLARIZER TYPE: T:TRANSMISSIVE; F:TRANSFLECTIVE: O: OTHER LCD DISPLAY MODE: N: NEGATIVE; O:OTHER; TEMPERATURE RANGE: N: NORMAL TEMPERATURE; M:MIDDLE TEMPERATURE; W: WIDE TEMPERATURE; O:SUPER WIDE TEMPERATURE VIEWING DIRECTION: U: UPPER(12:00); D:DOWN(6:00); L: LEFT(9:00); R:RIGHT(3:00);F:FULL VIEW WITH TP: N: WITHOUT TOUCH PANEL; Y:WITH TOHCH PANEL SERIAL NUMBER:C: CSTN T: TFT SERIAL NUMBERA--Z. GRAPHIC MODULEs:NUMBER OF COMMONS AND SEGMENTs CHARACTER MODULEs: LCM SIZE;18:1.8";20:2.0"; 22:2.2"....... JEWEL HILL ELECTRONIC CO.,LTD. JH30240400B VER: 0.1 -2- Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. 1. General Specification Item Display Panel Display Format 240*RGBx400(H) Dots Colour 262k colours Pixel Pitch 0.054mmx0.162mm Active Area 38.88mm(W)*64.8mm(H) Outline Dimensions 45.04mm(W)*77.00mm(H)*2.0mm(T) LCD Type IPS Polarizer Mode Transmissive,Normally Black View Angle(U/D/L/R) 80/80/80/80 DEG Driver IC S6D04D1 Backlight LED Backlight Color White Backlight Driver Type External Power JH30240400B VER: 0.1 Remark -3- Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. 2. OutlineDraw XL XR YD XL YU XR YD XL YU 1 YU YD Double side tape T=0.05MM A 37 XR K2 K4 K1 K3 K5 hunter 37 1 K5 K3 K1 K4 K2 A 37 Double side tape T=0.05MM 1 PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 NAME LCM-ID XL YU XR YD GND IOVCC VCC FMARK CS RS WR RD D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 RESET NC A K1 K2 K3 K4 K5 Issue date: 2013/08/01 -4- VER: 0.1 JH30240400B YU XL YD XR JEWEL HILL ELECTRONIC CO.,LTD. 3. Absolute Maximum Ratings The following are maximum values which, if exceeded may cause operation or damage to the unit. ITEM Symbol Min . Typ. Max. Unit Power Supply for Logic Vcc – Vss 2.4 - 3.3 V Power Supply for LCD VGh – Vss 12 14 16 V Input Voltage VGL -10 -8 -6 V Storage Temperature TST -20 - 70 ℃ Operating Ambient temperature TOP -10 - 60 ℃ JH30240400B VER: 0.1 B B B B B B B B B -5- Remark Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. 4. Electrical Specification 4.1 Electrical Characteristics (Unless specified, the ambient temperature Ta=25℃) JH30240400B VER: 0.1 -6- Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. JH30240400B VER: 0.1 -7- Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. 4.2 LED Backlight Specification JH30240400B VER: 0.1 -8- Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. 4.3 Interface Signals Pin NO. Symbol Description 1 LCM-ID TBD 2 XL Touch Panel connection(NC) 3 YU Touch Panel connection(NC) 4 XR Touch Panel connection(NC) 5 YD Touch Panel connection(NC) 6 GND Ground 7 IOVCC A Power Supply For The Internal Logic(1.65-3.3V) 8 VCC A Power Supply For The Internal Logic:Vcc=2.8V 9 FMARK Frame Head Pulse Signal 10 CS LCD Chip Select Input Pin 11 RS Reg Selection For Command/Data 12 WR Write Execution Control Pin 13 RD Read Execution Control Pin 14-29 DB0-DB15 Data Bus 30 RESET Reset Pin 31 NC No Connect 32 A Backlight Anode 33 K1 Backlight Cathode1 34 K2 Backlight Cathode2 35 K3 Backlight Cathode3 36 K4 Backlight Cathode4 37 K5 Backlight Cathode5 JH30240400B VER: 0.1 -9- Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. 4.4 Interface Timing Chart JH30240400B VER: 0.1 - 10 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. JH30240400B VER: 0.1 - 11 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. 5. Optical Specification JH30240400B VER: 0.1 - 12 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. JH30240400B VER: 0.1 - 13 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. JH30240400B VER: 0.1 - 14 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. JH30240400B VER: 0.1 - 15 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. 6. Reliability JH30240400B VER: 0.1 - 16 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. 7. Quality Level 7.1. Notes For Quality Standard JH30240400B VER: 0.1 - 17 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. 7.2. Standards of Inspection Items JH30240400B VER: 0.1 - 18 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. JH30240400B VER: 0.1 - 19 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. JH30240400B VER: 0.1 - 20 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. 8.PRECAUTIONS FOR USING LCD MODULES Handing Precautions (1) The display panel is made of glass and polarizer. As glass is fragile, it tends to become or chipped during handling especially on the edges. Please avoid dropping or jarring. Do not subject it to a mechanical shock by dropping it or impact. (2) If the display panel is damaged and the liquid crystal substance leaks out, be sure not to get any in your mouth. If the substance contacts your skin or clothes, wash it off using soap and water. (3) Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. Do not touch the display with bare hands. This will stain the display area and degraded insulation between terminals (some cosmetics are determined to the polarizer). (4) The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle this polarizer carefully. Do not touch, push or rub the exposed polarizers with anything harder than an HB pencil lead (glass, tweezers, etc.). Do not put or attach anything on the display area to avoid leaving marks on. Condensation on the surface and contact with terminals due to cold will damage, stain or dirty the polarizer. After products are tested at low temperature they must be warmed up in a container before coming is contacting with room temperature air. (5) If the display surface becomes contaminated, breathe on the surface and gently wipe it with a soft dry cloth. If it is heavily contaminated, moisten cloth with one of the following solvents - Isopropyl alcohol - Ethyl alcohol Do not scrub hard to avoid damaging the display surface. (6) Solvents other than those above-mentioned may damage the polarizer. Especially, do not use the following. - Water - Ketone - Aromatic solvents Wipe off saliva or water drops immediately, contact with water over a long period of time may cause deformation or color fading. Avoid contacting oil and fats. (7) Exercise care to minimize corrosion of the electrode. Corrosion of the electrodes is accelerated by water droplets, moisture condensation or a current flow in a high-humidity environment. (8) Install the LCD Module by using the mounting holes. When mounting the LCD module make sure it is free of twisting, warping and distortion. In particular, do not forcibly pull or bend the I/O cable or the backlight cable. JH30240400B VER: 0.1 - 21 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. (9) Do not attempt to disassemble or process the LCD module. (10) NC terminal should be open. Do not connect anything. (11) If the logic circuit power is off, do not apply the input signals. (12) Since LCM has been assembled and adjusted with a high degree of precision, avoid applying excessive shocks to the module or making any alterations or modifications to it. - Do not alter, modify or change the shape of the tab on the metal frame. - Do not make extra holes on the printed circuit board, modify its shape or change the positions of components to be attached. - Do not damage or modify the pattern writing on the printed circuit board. - Absolutely do not modify the zebra rubber strip (conductive rubber) or heat seal connector. - Except for soldering the interface, do not make any alterations or modifications with a soldering iron. - Do not drop, bend or twist LCM. Storage Precautions When storing the LCD modules, the following precaution is necessary. (1) Store them in a sealed polyethylene bag. If properly sealed, there is no need for the dessicant. (2) Store them in a dark place. Do not expose to sunlight or fluorescent light, keep the temperature between 0°C and 35°C. (3) The polarizer surface should not come in contact with any other objects. (We advise you to store them in the container in which they were shipped). Others Liquid crystals solidify under low temperature (below the storage temperature range) leading to defective orientation or the generation of air bubbles (black or white). Air bubbles may also be generated if the module is subject to a low temperature. If the LCD modules have been operating for a long time showing the same display patterns, the display patterns may remain on the screen as ghost images and a slight contrast irregularity may also appear. A normal operating status can be regained by suspending use for some time. It should be noted that this phenomenon does not adversely affect performance reliability. To minimize the performance degradation of the LCD modules resulting from destruction caused by static electricity etc., exercise care to avoid holding the following sections when handling the modules. - Exposed area of the printed circuit board. -Terminal electrode sections. JH30240400B VER: 0.1 - 22 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. .ROHS COMPLIANT WARRANTY. JH30240400B VER: 0.1 - 23 - Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. 9. REVISION HISTORY. Version 00 0.1 Revise record Original version Perfect the VER00 spec，Commany internal modify. JH30240400B VER: 0.1 - 24 - Date 11-06-30 13-08-01 Issue date: 2013/08/01 JEWEL HILL ELECTRONIC CO.,LTD. SAMPLE APPROVED REPORT (样品确认单) SAMPLE MODEL NO. (样品型号) JH30240400B SAMPLE SERIES NUMBER NO. (样品序号) SAMPLE QUANTITY (样品数量) 2PCS COLOR/TYPE (底色/类型) TFT/NEGATIVE VIEWING DIRECTION (视角) FULL VIEW DRIVING METHOD (驱动参数) - LOGIC VOLTAGE (工作电压) 2.8V LCD VOP (LCD 驱动电压) - OPERATING TEMP. (操作温度) ℃ -10~60℃ STORAGE TEMP. (储存温度) ℃ -20~70℃ POLARIZER----FRONT (首偏光片) TRANSMISSIVE POLARIZER----BACK (后偏光片) CONTROLLER/DRIVER IC(控制/驱动 IC) S6D04D1（COG） BACKLIGHT COLOR/TYPE (背光源类型/颜色) BACKLIGHT VOLTAGE (背光电压) SPECIFICATION (规格书 LED/WHITE - 份数) 1BATE REMARKS： (备注) WRIT BY：_________ DATE：_________ APROV BY：_________ DATE：________ CUSTOMER’S APPROVAL (客户确认)： 1） FUNCTION （功能）： OK N.G. 2） DRIVER CONDITION （驱动条件）： OK N.G. 3） DISPLAY MODE （显示模式）： OK N.G. 4） VIEWING ANGLE （视角）： OK N.G. 5） BACKLIGHT （背光源）： OK N.G. 6） DISPLAYING PATTERN （显示效果）： OK N.G. CUSTOMER’S CONCLUSIONS (客户意见)：______________________________________ _______________________________________________________________________________ ________________________________________ CUSTOMER’S SIGNATURE（客户签名）：_____________ DATE (日期)：___________ JH30240400B VER: 0.1 - 25 - Issue date: 2013/08/01