ISL5314 ® Data Sheet July 28, 2005 FN4901.2 Direct Digital Synthesizer Features The 14-bit ISL5314 provides a complete Direct Digital Synthesizer (DDS) system in a single 48-pin LQFP package. A 48-bit Programmable Carrier NCO (numerically controlled oscillator) and a high speed 14-bit DAC (digital to analog converter) are integrated into a stand alone DDS. • 125MSPS output sample rate with 5V digital supply The DDS accepts 48-bit center and offset frequency control information via a parallel processor interface. A 40-bit frequency tuning word can also be loaded via an asynchronous serial interface. Modulation control is provided by 3 external pins. The PH0 and PH1 pins select phase offsets of 0, 90, 180 and 270 degrees, while the ENOFR pin enables or zeros the offset frequency word to the phase accumulator. The parallel processor interface has an 8-bit write-only data input C(7:0), a 4-bit address A(3:0) bus, a Write Strobe (WR), and a Write Enable (WE). The processor can update all registers simultaneously by loading a set of master registers, then transfer all master registers to the slave registers by asserting the UPDATE pin. Ordering Information Q48.7x7A ISL5314INZ (See Note) -40 to 85 48 LQFP (Pb-free) Q48.7x7A ISL5314EVAL2 25 • Small 48-pin LQFP packaging • Pb-Free plus anneal available (RoHS compliant) Applications • Programmable local oscillator • FSK, PSK modulation • Direct digital synthesis • Clock generation 48-PIN LQFP (Q48.7X7A) TOP VIEW Evaluation Board NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. SLAVE MASTER PHASE ACCUM. COMPOUT Block Diagram + ININ+ C2 C1 C0 ENOFR DGND CLK DVDD RESET UPDATE COMPOUT REFLO REFIO 48 47 46 45 44 43 42 41 40 39 38 37 36 35 2 34 3 33 4 32 5 31 6 ISL5314 30 7 29 8 28 9 27 10 26 11 25 12 13 14 15 16 17 18 19 20 21 22 23 24 1 A2 A3 PH0 PH1 SSYNC DVDD SCLK DGND DGND SDATA DVDD DGND ∑ UPDATE SERIAL MODULATION CONTROL CONTROL ENOFR PH(1:0) • Offset frequency register and enable pin for fast FSK C3 C4 C5 C6 C7 DVDD WR DGND WE NC A0 A1 48 LQFP SDATA SSYNC SCLK • 48-bit programmable frequency control Pinout -40 to 85 WR WE • Parallel control interface for fast tuning (50MSPS control register write rate) and serial control interface TEMP. RANGE (°C) PACKAGE PKG. DWG. # ISL5314IN C(7:0) A(3:0) • 14-bit digital-to-analog (DAC) with internal reference COMP1 COMP2 SINE WAVE ROM 14 BIT DAC IOUTA IOUTB INT REF REFIO REFLO FSADJ COMP1 AGND AGND IOUTB IOUTA COMP2 AVDD AGND IN+ INAGND PART # • 100MSPS output sample rate with 3.3V digital supply RESET CLK 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2000, 2005. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ISL5314 Typical Application Circuit (Parallel Control Mode, Sinewave Generation) 3 SDATA, SSYNC, SCLK (IN PARALLEL CONTROL MODE, SERIAL CONTROL CAN ALSO BE USED IF DESIRED.) WRITE CLOCK (WR) WRITE ENABLE µPROCESSOR/ 8 C7:C0 BUS C3 C4 C5 C6 C7 DVDD WR DGND WE NC A0 A1 FPGA/CPLD 4 A3:A0 BUS 48 47 46 45 44 43 42 41 40 39 38 37 36 35 2 34 3 33 4 32 5 31 6 ISL5314 30 7 29 8 28 9 27 10 26 11 25 12 13 14 15 16 17 18 19 20 21 22 23 24 CLOCK SOURCE fCLK DVPP 0.1µF A2 A3 PH0 PH1 SSYNC DVDD SCLK DGND DGND SDATA DVDD DGND 1 C2 C1 C0 ENOFR DGND CLK DVDD RESET UPDATE COMPOUT REFLO REFIO FSADJ COMP1 AGND AGND IOUTB IOUTA COMP2 AVDD AGND IN+ INAGND AVPP 0.1µF 0.1µF AVPP 2kΩ 0.1µF 50Ω 50Ω (IOUTA) ANALOG OUTPUT FERRITE BEAD DVPP (DIGITAL POWER PLANE) + 10µH 10µF +5V POWER SOURCE FERRITE BEAD 0.1µF 10µF DGND 10µH 0.1µF AGND 2 1µF AVPP (ANALOG POWER PLANE) + 1µF 0.1µF DVPP 0.1µF 0.1µF RSET DVPP ISL5314 Functional Description The ISL5314 is an NCO with an integrated 14-bit DAC designed to run in excess of 125MSPS. The NCO is a 16-bit output design, which is rounded to fourteen bits for input to the DAC. The frequency control is the sum of a 48-bit center frequency word, a 48-bit offset frequency word, and a 40-bit serially loaded tuning word. The three components are added modulo 48 bits with the alignment shown in Table 1. Each of the three terms can be zeroed independently (via the microprocessor interface for the center and serial frequency registers and via the ENOFR pin for the offset frequency term). Frequency Generation The output frequency of the part is determined by the summation of three registers: fOUT = fCLK x ((CF + OF +SF) mod (248))/ (248), where CF is the center frequency register, OF is the offset frequency register, SF is the serial frequency register and fCLK is the DDS clock rate. With a 125MSPS clock rate, the center frequency can be programmed to (125 x 106)/(248) = 0.4 µHz resolution. The addition of the frequency control words can be interpreted as two’s complement if convenient. For example, if the center frequency is set to 4000...00h and the offset frequency set to C000..00h, the programmed center frequency would be fCLK/4 and the programmed offset frequency -fCLK/4. The sum would be 10000..00h, but because only the lower 48 bits are retained, the effective frequency would be 0. In reality, frequencies above 8000...00h alias below fCLK/2 (the output of the part is real), so the MSB is only provided as a convenience for two’s complement calculations. The frequency control of the NCO is the change in phase per clock period or dφ/dt. This is integrated by the phase accumulator to obtain frequency. The most significant 24 bits of phase are then mapped to 16 bits of amplitude in a sine look-up table function. The range of dφ/dt is 0–1 with 1 equaling 360 degrees or (2 x pi) per clock period. The phase accumulator output is also 0–1 with 1 equaling 360 degrees. The operations are modulo 48 bits because the MSB (bit 47) aligns with the most significant address bit of the sine ROM and the ROM contains one cycle of a sinusoid. The MSB is weighted at 180 degrees. Full scale is 360 degrees minus one LSB and the phase then rolls over to 0 degrees for the next cycle of the sinusoid. four address pins (A3:A0), a write strobe (WR), and a write enable (WE). The interface is a master/slave type. The processor interface loads a set of master registers. The contents of the master set of registers is then transferred to a slave set of registers by asserting a pin (UPDATE). This allows all of the bits of the frequency control to be updated simultaneously. The rate which the user writes (WR) to these registers does not have to be the same rate as the DDS clock rate (the rate of the NCO and DAC; pin CLK). It is expected that most applications will have a slower register write rate than the DDS clock rate. It takes one WR cycle at the write rate for each register that is written and another eleven CLK cycles at the DDS rate to write and obtain a new output, assuming that the UPDATE pin is always active. If the UPDATE pin is not active until after the new word has been written, it takes fourteen CLK cycles, rather than eleven. For cases which require the output to be updated with all of the new frequency information present, it is necessary that the UPDATE be inactive until after all of the new frequency word has been written to the device. See the Timing Diagrams for more information. The parallel registers can be written at a rate of CLK/2, such that updated control words can be pipelined. If the application does not require all registers to be written, then the output frequency can be changed more quickly. For example, if only 32 bits of frequency information are needed and it is desired that the output be updated all at once, then it takes four WR cycles, then the assertion low of the UPDATE pin, plus another fourteen CLK cycles at the DDS rate to write and update a new frequency. The timing is the same whether writing to the center or offset frequency registers. For faster frequency update, consider the ENOFR (Enable Offset Frequency Register) option. Once the values have been written to the center and offset frequency registers, the user can enable and disable the offset frequency register, which is added to the center frequency value when enabled. The ENOFR pin has a latency of fourteen CLK cycles, but simplifies the interface because the only pin that has to be toggled is the ENOFR pin. See the FSK explanation for more information. Serial Interface The DDS can be clocked with either a sinusoidal or a square wave. Refer to the digital inputs VIH and VIL values in the electrical specifications table. A serial interface is provided for loading a tuning frequency. This interface can be asynchronous to the master clock of the part. When the tuning word has been shifted into the part, it is loaded into a holding register by the serial interface clock, SCLK. This loading triggers a synchronization circuit to transfer the data to a slave register synchronous with the master clock. A minimum of eleven serial clocks (at minimum serial word size of eight) are necessary to complete the transfer to the slave register. Another twelve DDS CLK cycles are necessary before the output of the DDS reflects the new frequency. Parallel Interface Serial loading latency = ((8 x N + 3) x SCLK)+ 12 x fCLK, The processor interface is an 8-bit parallel write only interface. The interface consists of eight data bits (C7:C0), 3 ISL5314 TABLE 1. FREQUENCY CONTROL BIT ALIGNMENTS 48 Bits (Individual Bit Alignment) 4444 4444 3333 3333 3322 2222 2222 1111 1111 1100 0000 0000 7654 3210 9876 5432 1098 7654 3210 9876 5432 1098 7654 3210 Phase Accumulator xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx Center Frequency xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx Offset Frequency xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx Serial Frequency, 8 Bits xxxx xxxx 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 Serial Frequency, 16 Bits xxxx xxxx xxxx xxxx 0000 0000 0000 0000 0000 0000 0000 0000 Serial Frequency, 24 Bits xxxx xxxx xxxx xxxx xxxx xxxx 0000 0000 0000 0000 0000 0000 Serial Frequency, 32 Bits xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx 0000 0000 0000 0000 Serial Frequency, 40 Bits xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx 0000 0000 where N = 1–5 (for 8–40 bit serial data) and fCLK is the DDS clock rate. Three extra SCLKs are required (one for the SYNC pulse plus two additional for register transfer). The latency in seconds depends on how many bits of serial data are being written and the speeds of both clocks. The center and offset frequency registers cannot be written using the serial pins. They must be programmed using the parallel interface. all registers. After RESET goes high, one rising edge of CLK is required before the control registers can be written to again. The center frequency register resets to fCLK/4. The offset frequency register resets to an unknown frequency but is disabled. The serial frequency register resets to an unknown frequency and is enabled. If the serial register is not used, disable it in register 13 using the parallel interface. In order to use the three wire serial interface in a mode that is not the default mode, the parallel control bus must be used to reprogram register 12. Register 12 can be set according to the desired options of the serial interface that are described in the register description table. Since the serial register defaults enabled, it must be disabled in register 13 (bit 6) if it is not used. Comparator Register 14 The parallel control bus must be used to program register 14 with 0x00h or 0x30h after assertion of RESET. See the Control Register table in the back of the datasheet for more information. Control Pins There are three control pins provided for phase and frequency control. The PH0 and PH1 pins select phase offsets of 0, 90, 180, and 270 degrees and can be used for low speed, unfiltered BPSK or QPSK modulation. These pins can also be used for providing sine/cosine when using two ISL5314s together as quadrature local oscillators. The ENOFR pin enables or zeros the offset frequency word to the phase accumulator and can be used for FSK or MSK modulation. These control pins and the UPDATE pin are passed through special cells to minimize the probability of metastability. Writing anything to register 15 behaves like an UPDATE so that the user can save one control pin if desired. Reset A RESET pin is available which resets all registers to their defaults. Register 14 must always be written with 0x00h or 0x30h after a RESET. In order to reset the part, the user must take the RESET pin low, allow at least one CLK rising edge, and then take the RESET pin high again. The latency from the RESET pin going high until the output reflects the reset is eleven CLK cycles. See the register description table in the back of the data sheet for the default states of all bits in 4 A comparator is provided for square wave output generation. The user can take the DDS analog output, filter it, and then send it back into the comparator. A square wave will be generated at the comparator output (COMPOUT pin) at an amplitude level that is dependent on the digital power supply (DVDD). The comparator was designed to operate at speeds comparable to the DDS output frequency range (approximately 0–50MHz). It is not intended for low jitter applications (<0.5ns). The comparator has a sleep mode that is activated by connecting both inputs (IN- and IN+) to the analog power supply plane. This will save approximately 4mA of current (as shown in the Typical Application Circuit). If the comparator is not used, leave the COMPOUT pin floating. DAC Voltage Reference The internal voltage reference for the DAC has a nominal value of +1.2V with a ±60ppm/ oC drift coefficient over the full temperature range of the converter. It is recommended that a 0.1µF capacitor be placed as close as possible to the REFIO pin, connected to the analog ground. The REFLO pin (11) selects the reference. The internal reference can be selected if pin 11 is tied low (ground). If an external reference is desired, then pin 11 should be tied high (the analog supply voltage) and the external reference driven into REFIO, pin 12. The full-scale output current of the converter is a function of the voltage reference used and the value of RSET. IOUT should be within the 2mA–20mA range, though operation below 2mA is possible, with performance degradation. If the internal reference is used, VFSADJ will equal approximately 1.2V (pin 13). If an external reference is used, VFSADJ will equal the external reference. IOUT(Full Scale) = (VFSADJ/RSET) X 32. ISL5314 Analog Output Application Considerations IOUTA and IOUTB are complementary current outputs. They are generated by a 14-bit DAC that is capable of running at the full 125MSPS rate. The DDS clock also clocks the DAC. The sum of the two output currents is always equal to the full scale output current minus one LSB. If single-ended use is desired, a load resistor can be used to convert the output current to a voltage. It is recommended that the unused output be equally terminated. The voltage developed at the output must not violate the output voltage compliance range of -1.0V to +1.25V. RLOAD (the impedance loading each current output) should be chosen so that the desired output voltage is produced in conjunction with the output full scale current. If a known line impedance is to be driven, then the output load resistor should be chosen to match this impedance. The output voltage equation is: Ground Plane VOUT = IOUT X RLOAD. These outputs can be used in a differential-to-single-ended arrangement. This is typically done to achieve better harmonic rejection. Because of a mismatch in IOUTA and IOUTB, the transformer does not improve the harmonic rejection. However, it can provide voltage gain without adding distortion. The SFDR measurements in this data sheet were performed with a 1:1 transformer on the output of the DDS (see Figure 1). With the center tap grounded, the output swing of pins 17 and 18 will be biased at zero volts. The loading as shown in Figure 1 will result in a 500mVP-P signal at the output of the transformer if the full scale output current of the DAC is set to 20mA. REQ IS THE IMPEDANCE LOADING EACH OUTPUT 50Ω PIN 17 VOUT = (2 x IOUT x REQ)VPP IOUTB 100Ω PIN 18 ISL5314 50Ω IOUTA 50Ω Separate digital and analog ground planes should be used. All of the digital functions of the device and their corresponding components should be located over the digital ground plane and terminated to the digital ground plane. The same is true for the analog components and the analog ground plane. Pins 11 through 24 are analog pins, while all the others are digital. Noise Reduction To minimize power supply noise, 0.1µF capacitors should be placed as close as possible to the power supply pins, AVDD and DVDD. Also, the layout should be designed using separate digital and analog ground planes and these capacitors should be terminated to the digital ground for DVDD and to the analog ground for AVDD. Additional filtering of the power supplies on the board is recommended. Power Supplies The DDS will provide the best SFDR (spurious free dynamic range) when using +5V analog and +5V digital power supply. The analog supply must always be +5V (±10%). The digital supply can be either a +3.3V (±10%), a +5V (±10%) supply, or anything in between. The DDS is rated to 125MSPS when using a +5V digital supply and 100MSPS when using a +3.3V digital supply. Improving SFDR +5V power supplies provides the best SFDR. Under some clock and output frequency combinations, particularly when the fCLK/fOUT ratio is less than 4, the user can improve SFDR even further by connecting the COMP2 pin (19) of the DDS to the analog power supply. The digital supply must be +5V if this option is explored. Improvements as much as 6dBc in the SFDR-to-Nyquist measurement were seen in the lab. FSK Modulation 50Ω REPRESENTS THE SPECTRUM ANALYZER FIGURE 1. TRANSFORMER OUTPUT CIRCUIT OPTION VOUT = 2 x IOUT x REQ, where REQ is 12.5Ω. Allowing the center tap to float will result in identical transformer output, however the output pins of the DAC will have positive DC offset, which could limit the voltage swing available due to the output voltage compliance range. The 50Ω load on the output of the transformer represents the load at the end of a ‘transmission line’, typically a spectrum analyzer, oscilloscope, or the next function in the signal chain. The necessity to have a 50Ω impedance looking back into the transformer is negated if the DDS is only driving a short trace. The output voltage compliance range does limit the impedance that is loading the DDS output. Binary frequency shift keying (BFSK) can be done by using the offset frequency register and the ENOFR pin. M-ary FSK or GFSK (Gaussian) can be done by continuously loading in new frequency words. The maximum FSK data rate of the ISL5314 depends on the way the user programs the device to do FSK, and the form of FSK. For example, simple BFSK is efficiently performed with the ISL5314 by loading the center frequency register with one frequency, the offset frequency register with another frequency, and toggling the ENOFR (enable offset frequency register) pin. The latency is fourteen CLK cycles between assertion of the ENOFR pin and the change occurring at the analog output. However, the change in frequency can be pipelined such that the ENOFR can be toggled at a rate up to ENOFRMAX = fCLK/2, where fCLK is the frequency of the master CLK. 5 ISL5314 If M-ary FSK is required (more than two frequencies), the user will have to continually reprogram the center frequency register. The maximum write rate to the same parallel register is the lesser of 50MSPS or fCLK/2. One WR clock cycle is required for every register updated. The maximum possible rate occurs if the user only needs to change eight bits (one register). For Mary FSK, the output frequency rate of change is effect on the intended load. The average value is used as the reference voltage for one input to the comparator, with a capacitor to filter off any high frequency noise. The other comparator input is connected to the lowpass filter output. It is important that both IOUTA and IOUTB are equally loaded so that each generates the same amplitude and therefore has the same average value. ISL5314 IN- M-ary FSK Rate = WR / REG, PIN 23 where REG = quantity of registers being written and WR = write rate. PIN 22 PSK Modulation PIN 18 COMPARATOR INPUTS IN+ >1nF 100Ω Binary or quadrature phase shift keying (PSK) can be done by using the phase pins, PH0 and PH1. The change in phase can be pipelined such that the PH pins can be toggled at a rate up to PHMAX = fCLK/2, Quadrature Local Oscillators Two ISL5314s can be used as sine/cosine generators for quadrature local oscillator applications. It is important to note that the phase accumulator feedback needs to be zeroed in both devices if it is desired that both DDSs restart with a known phase, which is determined by the use of the phase control pins, PH1 and PH0. To zero the phase accumulator, pull bit 5 of address 13 low and then high again at the same time in both devices. Squarewave Clock Source The on-chip comparator can be used to generate a square wave. The analog output is filtered and then fed into the comparator input. Because the analog output is a sampledwaveform, a high DAC output frequency (relative to the clock rate) creates large amplitude steps in the sampled waveform. These steps have to be smoothed with a lowpass filter in order for the comparator to operate properly, otherwise the zero-order hold nature of the sampled analog output could possibly hold at the comparator’s trigger point temporarily causing the comparator to toggle unexpectedly. For this reason, it is very important that a lowpass filter be used on the analog output prior to the input of the comparator. The user can set one input to the comparator at a DC reference point (typically the mid-point of the filtered signal) and feed the filtered analog output into the other input. See Figure 2 for an example of a square wave circuit using this method. Since IOUTA and IOUTB are differential, the mid-point between the 10k resistors will always be the average value of each signal. The large resistors have to be used so that the parallel resistance of the intended load and the extra load of the averaging circuit yields a negligible 6 >10kΩ (TYP 20-40MHz) 100Ω >10kΩ PIN 17 IOUTB 50Ω PIN 10 where fCLK is the frequency of the master CLK. LPF (100Ω) IOUTA COMPOUT FIGURE 2. SQUAREWAVE GENERATION USING THE ON-CHIP COMPARATOR The user can filter both IOUTA and IOUTB and feed them differentially into the comparator. It is difficult to perfectly match the differential option, so the single-ended option is recommended. The jitter of the comparator is typically 500ps peak to peak. The actual jitter achieved is partially dependent on the quality of the signal at the comparator input, which is dictated by the amount of oversampling of the analog output and the quality of the lowpass filter. The user also has the option to evaluate the comparator circuit in Figure 2 with lower output current in order to save power consumption in the ISL5314. The DAC output current can be set to 5 or 10mA instead of 20mA and evaluated to determine if the comparator performance is still suitable for the application. Since the output current is derived from the +5V analog supply, reducing the output from 20mA to 10mA saves approximately 50mW of power. The recommended minimum amplitude of the comparator input is 100mV, so operation of the analog outputs with less than 20mA of output current should be possible with appropriate resistive loading (for example, 5mA into a 50Ω load provides 250mV of amplitude). If needed, series resistance on the comparator output can be used to reduce overshoot and/or ringing. The comparator can be used to drive a 50Ω load. ISL5314 Absolute Maximum Ratings Thermal Information Digital Supply Voltage DVDD to DGND . . . . . . . . . . . . . . . . . . +5.5V Analog Supply Voltage AVDD to AGND . . . . . . . . . . . . . . . . . . +5.5V Grounds, AGND To DGND. . . . . . . . . . . . . . . . . . . . . -0.3V To +0.3V Digital Input Voltages . . . . . . . . . . . . . . . . . . . . . . . . . DVDD + 0.3V Reference Input Voltage Range . . . . . . . . . . . . . . . . . . AVDD + 0.3V Analog Output Current (IOUT) . . . . . . . . . . . . . . . . . . . . . . . . . 24mA Thermal Resistance (Typical, Note 1) θJA(oC/W) LQFP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . .150oC Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300oC Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details. AVDD = DVDD = +5V (unless otherwise noted), VREF = Internal 1.2V, IOUTFS = 20mA, TA = -40oC to 85oC for all Min and Max Values. TA = 25oC for All Typical Values Electrical Specifications PARAMETER TEST CONDITIONS MIN TYP MAX UNITS 14 - - Bits DAC CHARACTERISTICS DAC Resolution Integral Linearity Error, INL “Best Fit” Straight Line (Note 7) -5 +2.5 +6 LSB Differential Linearity Error, DNL (Note 7) -2 +1.5 +4 LSB Offset Error, IOS (Note 7) -0.025 +0.025 % FSR Offset Drift Coefficient (Note 7) - 0.1 - ppm FSR/oC Full Scale Gain Error With Internal Reference (Notes 2, 7) -10 ±1 +10 % FSR Full Scale Gain Drift With Internal Reference (Note 7) - ±50 - ppm FSR/oC Full Scale Output Current (Note 3) 2 - 20 mA Output Voltage Compliance Range (Note 3, 7) -1.0 - 1.25 V Maximum Clock Rate, fCLK +5V DVDD , +5V AVDD (Note 3) 125 - - MSPS Maximum Clock Rate, fCLK +3.3V DVDD , +5V AVDD (Note 3) 100 - - MSPS Output Settling Time, (tSETT) ±0.05% (±8 LSB) (Note 7) - 35 - ns Output Rise Time Full Scale Step - 2.5 - ns Output Fall Time Full Scale Step - 2.5 - ns - 25 - pF IOUTFS = 20mA - 50 - pA/√Hz IOUTFS = 2mA - 30 - pA/√Hz fCLK = 100MSPS, fOUT = 20MHz, 5MHz Span - 93 - dBc fCLK = 100MSPS, fOUT = 5MHz, 8MHz Span - 93 - dBc fCLK = 50MSPS, fOUT = 5MHz, 8MHz Span - 93 - dBc DAC DYNAMIC CHARACTERISTICS Output Capacitance Output Noise AC CHARACTERISTICS Spurious Free Dynamic Range, SFDR Within a Window (Notes 4, 7) 7 ISL5314 AVDD = DVDD = +5V (unless otherwise noted), VREF = Internal 1.2V, IOUTFS = 20mA, TA = -40oC to 85oC for all Min and Max Values. TA = 25oC for All Typical Values (Continued) Electrical Specifications PARAMETER TEST CONDITIONS MIN TYP MAX UNITS fCLK = 125MSPS, fOUT = 40.4MHz - 40 - dBc fCLK = 125MSPS, fOUT = 10.1MHz 57 63 - dBc fCLK = 125MSPS, fOUT = 5.02MHz - 72 - dBc fCLK = 100MSPS, fOUT = 40.4MHz - 40 - dBc fCLK = 100MSPS, fOUT = 20.2MHz - 49 - dBc fCLK = 100MSPS, fOUT = 5.04MHz - 72 - dBc fCLK = 100MSPS, fOUT = 2.51MHz - 73 - dBc fCLK = 50MSPS, fOUT = 20.2MHz - 45 - dBc fCLK = 50MSPS, fOUT = 5.02MHz - 68 - dBc fCLK = 50MSPS, fOUT = 2.51MHz - 72 - dBc fCLK = 50MSPS, fOUT = 1.00MHz - 71 - dBc fCLK = 25MSPS, fOUT = 1.0MHz - 72 - dBc 1.13 1.2 1.28 V Internal Reference Voltage Drift - ±60 - ppm/oC Internal Reference Output Current Sink/Source Capability - ±0.1 - µA Reference Input Impedance - 1 - MΩ Reference Input Multiplying Bandwidth (NoteNotes 4, 7) - 1.4 - MHz Spurious Free Dynamic Range, SFDR to Nyquist (fCLK/2) (Notes 4, Notes 4, 7) DAC REFERENCE VOLTAGE Internal Reference Voltage, VFSADJ Pin 13 Voltage with Internal Reference DIGITAL INPUTS Input Logic High Voltage with 5V Digital Supply, VIH (Note 3) 3.5 5 - V Input Logic High Voltage with 3V Digital Supply, VIH (Note 3) 2.0 3 - V Input Logic Low Voltage with 5V Digital Supply, VIL (Note 3) - 0 1.3 V Input Logic Low Voltage with 3V Digital Supply, VIL (Note 3) - 0 0.8 V Input Logic Current, IIH -10 - +10 µA Input Logic Current, IIL -10 - +10 µA - 4 - pF Digital Input Capacitance, CIN TIMING CHARACTERISTICS Maximum Clock Rate, fCLK +5V DVDD , +5V AVDD (Note 3) 125 - - MSPS Maximum Clock Rate, fCLK +3.3V DVDD , +5V AVDD (Note 3) 100 - - MSPS CLK Pulse Width, tCW CLK pin (Note 3) 5 - - ns Maximum Parallel Write Rate Rate of WR pin 50 - - MSPS WR Pulse Width, tWW (Note 3) 5 - - ns Data Setup Time, tDS Between DATA and WR (Note 3) 10 - - ns Data Hold Time, tDH Between DATA and WR (Note 3) 0 - - ns Address Setup Time, tAS Between ADDR and WR (Note 3) 12 - - ns 8 ISL5314 AVDD = DVDD = +5V (unless otherwise noted), VREF = Internal 1.2V, IOUTFS = 20mA, TA = -40oC to 85oC for all Min and Max Values. TA = 25oC for All Typical Values (Continued) Electrical Specifications PARAMETER TEST CONDITIONS MIN TYP MAX UNITS Address Hold Time, tAH Between ADDR and WR (Note 3) 0 - - ns UPDATE Pulse Width, tUW (Note 3) 5 - - ns UPDATE Setup Time, tUS Between UPDATE and CLK (Note 3) 1 - - ns UPDATE Hold Time, tUH Between UPDATE and CLK (Note 3) 3 - - ns UPDATE Latency, tUL After UPDATE, before analog output change, if asserted after writing to the control registers - 14 - Clock Cycles UPDATE Latency, tUL After UPDATE, before analog output change, if asserted before writing to the control registers - 11 - Clock Cycles Maximum PH Rate Rate of PH1 and PH0 pins (Note 3) fCLK/2 - - Hz Phase Pulse Width, tPW PH(1:0) (Note 3) 5 - - ns Phase Setup Time, tPS Between PH(1:0) change and CLK (Note 3) 1 - - ns Phase Hold Time, tPH Between PH(1:0) change and CLK (Note 3) 3 - - ns Phase Latency, tPL Between PH(1:0) change and analog output change - 12 - Clock Cycles Maximum ENOFR Rate Rate of ENOFR (Note 3) fCLK/2 - - Hz ENOFR Pulse Width, tEW ENOFR (Note 3) 5 - - ns ENOFR Setup Time, tES Between ENOFR and CLK (Note 3) 1 - - ns ENOFR Hold Time, tEH Between ENOFR and CLK (Note 3) 3 - - ns ENOFR Latency, tEL After ENOFR, before analog output change - 14 - Clock Cycles Write Enable Pulse Width, tWR WE (Note 3) 5 - - ns Write Enable Setup Time, tWS Between WE and WR (Note 3) 2 - - ns Write Enable Hold Time, tWH Between WE and WR (Note 3) 4 - - ns RESET Pulse Width, tRW RESET (Note 3) 5 - - ns RESET Setup Time, tRS Between RESET and CLK 1 - - ns RESET Latency to Output, tRL After RESET, before analog output reflects reset values - 11 - Clock Cycles RESET Latency to Write, tRE After RESET, before the control registers can be written to - 1 - Clock Cycles Maximum SCLK Rate See Figure 6 Timing Diagrams (Note 3) 50 - - MSPS SCLK Pulse Width, tSCW See Figure 6 Timing Diagrams (Note 3) 5 - - ns SDATA Pulse Width, tSDW See Figure 6 Timing Diagrams (Note 3) 5 - - ns SDATA Setup Time, tSDS Between SDATA and SCLK. See Figure 6 Timing Diagrams. (Note 3) 6 - - ns SDATA Hold Time, tSDH Between SDATA and SCLK. See Figure 6 Timing Diagrams. (Note 3) 1 - - ns SSYNC Pulse Width, tSSW See Figure 6 Timing Diagrams (Note 3) 5 - - ns SSYNC Setup Time, tSSS Between SSYNC and SCLK. See Figure 6 Timing Diagrams. (Note 3) 6 - - ns SSYNC Hold Time, tSSH Between SSYNC and SCLK. See Figure 6 Timing Diagrams. (Note 3) 1 - - ns 9 ISL5314 Electrical Specifications AVDD = DVDD = +5V (unless otherwise noted), VREF = Internal 1.2V, IOUTFS = 20mA, TA = -40oC to 85oC for all Min and Max Values. TA = 25oC for All Typical Values (Continued) PARAMETER TEST CONDITIONS MIN TYP MAX UNITS Input Capacitance - 4 - pF Input Resistance - >1 - MΩ Input Current - 1 - µA - 4.0 3.75 V Minimum Input Voltage, Peak-to-Peak (Dependent on Noise) - 0.1 - VP-P Propagation Delay, High to Low (Note 8) - 6 - ns Propagation Delay, Low to High (Note 8) - 5 - ns Output Rise Time (Note 8) - 1.5 - ns Output Fall Time (Note 8) - 1.3 - ns Output High Voltage, VOH IOH = -4mA 2.6 - - V Output Low Voltage, VOL IOL = +4mA - - 0.4 V - 0.5 - ns - 100 - MHz AVDD (Analog) Power Supply 4.5 5.0 5.5 V DVDD (Digital) Power Supply 3.0 3.3 5.5 V 5V, IOUTFS = 20mA (Note 10) - 25 30 mA 5V, IOUTFS = 2mA - 7 - mA 5V (Notes 5, 10) - 90 100 mA 3.3V (Notes 6, 9) - 50 55 mA AVDD = 5V, DVDD = 3.3V, IOUTFS = 20mA (Notes 6, 9) - 290 363 mW AVDD = 5V, DVDD = 5V, IOUTFS = 20mA (Notes 5, 10) - 625 715 mW -0.2 - +0.2 % FSR/V COMPARATOR CHARACTERISTICS Maximum Input Voltage Allowed (Excluding Comparator Sleep Mode) Output Jitter Maximum Output Toggle Rate High Z Load (~1MΩ) POWER SUPPLY CHARACTERISTICS Analog Supply Current (IAVDD) Digital Supply Current (IDVDD) Power Dissipation Power Supply Rejection Single 5V Supply (Note 7) NOTES: 2. Gain error for the DAC is measured as the error in the ratio between the full scale output current and the current through RSET (typically 625µA); ideally the ratio should be 32. 3. Parameter guaranteed by design or characterization and not production tested. 4. Spectral measurements made with differential transformer coupled output and no external filtering. 5. Measured with the clock at 125MSPS and the output frequency at 10MHz. 6. Measured with the clock at 100MSPS and the output frequency at 10MHz. 7. See Definition of Specifications. 8. 50MHz, High Z Load (~1MΩ), 15pF capacitance, (IN- = 0.5VP-P), (IN+ = 0.25VDC). 9. For maximum value, 5.5V AVDD and 3.6V DVDD are used. 10. For maximum value, 5.5V AVDD and 5.5V DVDD are used. Definition of Specifications Differential Non-Linearity (DNL) is the measure of the step size output deviation from code to code. Ideally the step size should be one LSB. A DNL specification of one LSB or less guarantees monotonicity. 10 Integral Non-Linearity (INL) is the measure of the worst case point that deviates from a best fit straight line of data values along the transfer curve. Full Scale Gain Drift is measured by setting the DAC inputs to be all logic high (all 1’s) and measuring the output voltage through a known resistance as the temperature is varied from TMIN to TMAX . It is defined as the maximum deviation ISL5314 from the value measured at room temperature to the value measured at either TMIN or TMAX . The units are ppm of FSR (full scale range) per oC. Full Scale Gain Error is the error from an ideal ratio of 32 between the DAC output current and the full scale adjust current (through RSET). Internal Reference Voltage Drift is defined as the maximum deviation from the value measured at room temperature to the value measured at either TMIN or TMAX . The units are ppm per oC. Offset Drift is measured by setting the DAC inputs to all logic low (all 0’s) and measuring the output voltage through a known resistance as the temperature is varied from TMIN to TMAX . It is defined as the maximum deviation from the value measured at room temperature to the value measured at either TMIN or TMAX . The units are ppm of FSR (Full Scale Range) per degree oC. Offset Error is measured by setting the DAC inputs to all logic low (all 0’s) and measuring the output voltage through a known resistance. Offset error is defined as the maximum deviation of the output current from a value of 0mA. Output Settling Time is the time required for the output voltage to settle to within a specified error band measured from the beginning of the output transition. The measurement is done by switching quarter scale. Termination impedance was 25Ω due to the parallel resistance of the 50Ω loading on the output and the oscilloscope’s 50Ω input. This also aids the ability to resolve the specified error band without overdriving the oscilloscope. Output Voltage Compliance Range is the voltage limit imposed on the output. The output impedance should be chosen such that the voltage developed at either IOUTA or IOUTB does not violate the compliance range. Power Supply Rejection is measured using a single power supply. The nominal supply is varied ±10% and the change in the DAC full scale output current is noted. Reference Input Multiplying Bandwidth is defined as the 3dB bandwidth of the voltage reference input. It is measured by using a sinusoidal waveform as the external reference with the digital inputs to the DAC set to all 1’s. The frequency is increased until the amplitude of the output waveform is 0.707 (-3dB) of its original value. Spurious Free Dynamic Range (SFDR) is the amplitude difference from the fundamental signal to the largest harmonically or non-harmonically related spur within the specified frequency window. Timing Diagrams tWS WE tAS tWH tAH ADDR A0 A1 A2 AN DON’T CARE DATA W0 W1 W2 WN DON’T CARE tDS tDH WRITE DON’T CARE 1 WRITE CYCLE FOR EVERY REGISTER CLK (fCLK) DON’T CARE tUS UPDATE tUL = 14 CLK RISING EDGES tUD ANALOG OUT OLD FREQ NEW FREQ FIGURE 3. PARALLEL-LOAD METHOD 1, UPDATE ACTIVE AFTER LOADING REGISTERS (RESET = HIGH) 11 ISL5314 Timing Diagrams (Continued) tWH tWS WE tAS tAH ADDR DATA A0 A1 A2 AN DON’T CARE W0 W1 W2 WN DON’T CARE tDS tDH WRITE DON’T CARE 1 WRITE CYCLE FOR EVERY REGISTER CLK (fCLK) DON’T CARE tUL= 11 CLK RISING EDGES UPDATE PREVIOUS FREQ ANALOG OUT ENTIRE NEW FREQ PARTIAL UPDATES FIGURE 4. PARALLEL-LOAD METHOD 2, UPDATE ACTIVE WHILE LOADING REGISTERS (RESET = HIGH) ONE CLK RISING EDGE REQUIRED WHILE RESET LOW CLK (fCLK) tRS RESET tRL = 11 CLK RISING EDGES PREVIOUS REGISTER VALUES ANALOG OUT RESET REGISTER VALUES FIGURE 5. RESET TIMING AND LATENCY CLK (fCLK) tEH ENOFR tES CENTER FREQUENCY ONLY ANALOG OUT CENTER + OFFSET CENTER ONLY tEL = 14 CLK RISING EDGES FIGURE 6. ENOFR (ENABLE OFFSET FREQUENCY REGISTER) TIMING AND LATENCY (RESET = HIGH) 12 CENTER + OFFSET ISL5314 Timing Diagrams RESET (Continued) tSDW tSDS tSDH SERIAL DATA (8 BITS SHOWN; MAX IS 40) SDATA DON’T CARE SCLK DON’T CARE (CAN FREE RUN) SCLK EDGES = SERIAL BITS + 3 SERIAL FREQ tSSS REGISTER OLD FREQ IN THE SERIAL REGISTER tSSH NEW FREQ LOADED IN THE SERIAL REGISTER tSCW SSYNC t = 12 fCLK RISING EDGES tSSW CLK (fCLK) DON’T CARE DON’T CARE (ASSUMED CONTINUOUSLY RUNNING) OLD FREQ ANALOG OUT NEW FREQ FIGURE 7. SERIAL PROGRAMMING, SYNC EARLY MODE (REPRESENTS MINIMUM SCLKS REQUIRED. SCLK CAN FREE RUN.) CONTROL REGISTER 12 IS SET TO 0001 00XX. RESET SERIAL DATA (8 BITS SHOWN; MAX IS 40) SDATA DON’T CARE SCLK DON’T CARE (CAN FREE RUN) SCLK EDGES = SERIAL BITS + 3 OLD FREQ IN THE SERIAL REGISTER SERIAL FREQ REGISTER NEW FREQ LOADED IN THE SERIAL REGISTER SSYNC t = 12 fCLK RISING EDGES CLK (fCLK) DON’T CARE (ASSUMED CONTINUOUSLY RUNNING) DON’T CARE OLD FREQ ANALOG OUT NEW FREQ FIGURE 8. SERIAL PROGRAMMING, SYNC LATE BURST MODE (REPRESENTS MINIMUM SCLKS REQUIRED; SCLK CAN FREE RUN); CONTROL REGISTER 12 IS SET TO 0000 00XX. 13 ISL5314 Pin Descriptions PIN NO. PIN NAME TYPE PIN DESCRIPTION 44-48, 1-3 C(7:0) Input 8-bit processor input data bus. C7 is the MSB. Data is written to the control register selected on A(3:0) on the rising edge of WR when WE is active. 42 WR Input Write clock for the processor interface. Parallel data is clocked into the chip on the rising edge of WR. 40 WE Input Write enable. Active low. WE must be active when writing data to the chip. 35-38 A(3:0) Input Processor interface address bus. These pins select the destination register for data on the C(7:0) bus. A3 is the MSB. 6 CLK Clock NCO and DAC clock. The phase accumulator and DAC output update on the rising edge of this clock. CLK can be asynchronous to the WR clock. 8 RESET Input Reset. Active low. Resets control registers to their default states (see register description table) and zeroes the feedback in the phase accumulator. UPDATE must be low for Reset to occur. 30 SCLK Input Serial clock. Polarity is programmable. See control word 12. May be asynchronous to CLK. If not used, connect to DGND. 27 SDATA Input Serial data. See control word 12. If not used, connect to DGND. 32 SSYNC Input Serial sync. See control word 12. If not used, connect to DGND. 9 UPDATE Input Active low. Updates the active control registers only. It has no effect on the ENOFR or PH(1:0) pins. This pin is provided for updating an entire frequency word at once rather than byte by byte. 33, 34 PH(1:0) Input Phase offset bits. The phase of the output is shifted. If not used, these pins should be grounded. 00 – 0 degrees reference 01 – 90 degrees shift 10 – 180 degrees shift 11 – 270 degrees shift 4 ENOFR Input Enable offset frequency. Active high. When high, the offset frequency bus is enabled to the phase accumulator. When low, the offset frequency bus is zeroed. This pin does not affect the contents of the offset frequency registers. If not used, the pin should be grounded. 10 COMPOUT Output 11 REFLO Input Connect to analog ground to enable the DAC’s internal 1.2V reference or connect to AVDD to disable the internal reference. 12 REFIO Input Reference voltage input for the DAC if internal reference is disabled. Recommend the use of a 0.1µF cap to ground from the REFIO pin when a DC reference voltage is used. 13 FSADJ Full scale current adjust for the DAC. Use a resistor to ground (RSET) to adjust the full scale output current. Full Scale Output Current = 32 x VFSADJ/RSET, where VFSADJ equals the reference voltage. 14 COMP1 Noise reduction for the DAC. Connect a 0.1µF cap to AVDD plane. 19 COMP2 Noise reduction for the DAC. Connect a 0.1µF cap to AGND plane. 18 IOUTA Output DAC current output. 17 IOUTB Output DAC complementary current output. 20 AVDD Power Analog supply voltage. 15, 16, 21, 24 AGND GND 7, 26, 31, 43 DVDD Power 5, 25, 28, 29, 41 DGND GND Digital ground. 22, 23 IN+, IN- Input Comparator inputs. To power down the comparator, connect both of these pins to the analog power supply. This will conserve ~4mA of current. 39 NC NC 14 Comparator output. Analog ground. Digital supply voltage. No connect. ISL5314 Control Register Description BITS 0 7:0 Center frequency bits CF(7:0) (LSB). 00h 1 7:0 Center frequency bits CF(15:8). 00h 2 7:0 Center frequency bits CF(23:16). 00h 3 7:0 Center frequency bits CF(31:24). 00h 4 7:0 Center frequency bits CF(39:32). 00h 5 7:0 Center frequency bits CF(47:40) (MSB). (Reset gives fCLK/4 output). 40h 6 7:0 Offset frequency bits OF(7:0) (LSB). 00h 7 7:0 Offset frequency bits OF(15:8). 00h 8 7:0 Offset frequency bits OF(23:16). 00h 9 7:0 Offset frequency bits OF(31:24). 00h 10 7:0 Offset frequency bits OF(39:32). 00h 11 7:0 Offset frequency bits OF(47:40) (MSB). 00h 12 7:0 Serial input control word. 01h 7:5 Select number of serial frequency input bits: 1xx = 40-bit word (weighting same as CF(47:8)) 011 = 32-bit word (weighting same as CF(47:16)) 010 = 24-bit word (weighting same as CF(47:24)) 001 = 16-bit word (weighting same as CF(47:32)) 000 = 8-bit word (weighting same as CF(47:40)) 000b 13 14 15 DESCRIPTION RESET STATE* ADDRESS 4 Serial input sync position select: 1 = sync early. Sync is expected one serial clock period before the first data bit. 0 = sync late. Sync is expected one serial clock after the last data bit. 0b 3 Serial sync polarity: 1 = active low, 0 = active high. 0b 2 Serial clock polarity: 0 = rising edge, 1 = falling edge. 0b 1 Shift direction: 0 = MSB first, 1 = LSB first. 0b 0 Center frequency enable: 1 = enable, 0 = disable. This bit can be used to zero the center frequency (CF(47:0)) to the phase accumulator. This does not zero the processor interface registers—just the data path from the center frequency register to the phase accumulator. The center frequency resets to fCLK/4. 1b 7:0 NCO control word. F8h 7 Intersil reserved. Do not change. 1b 6 Serial output frequency register enable: 1 = enable, 0 = disable. This bit enables/disables the data path from the serial frequency register to the phase accumulator, without changing the value of the register. Should be disabled after RESET if not used. 1b 5 Phase accumulator feedback: 0 = accumulator feedback disabled, 1 = accumulator enabled. 1b 4:0 Intersil reserved. Do not change. 7:0 Test and timing control register. User must write 00h or 30h to register 14 after RESET. 10h 5:4 NCO-to-DAC setup and hold timing control. Write either 11b or 00b to these bits. 01b 7:0 Register 15 does not actually exist. Any write to register 15 is an UPDATE. This function is provided to save one microprocessor control pin from being used for the UPDATE pin, if the user chooses. N/A * b=binary, h=hex 15 11000b ISL5314 Thin Plastic Quad Flatpack Packages (LQFP) D Q48.7x7A (JEDEC MS-026BBC ISSUE B) 48 LEAD THIN PLASTIC QUAD FLATPACK PACKAGE D1 -D- INCHES SYMBOL -A- -B- E E1 e PIN 1 SEATING A PLANE -H- MIN MAX MILLIMETERS MIN MAX NOTES A - 0.062 - 1.60 - A1 0.002 0.005 0.05 0.15 - A2 0.054 0.057 1.35 1.45 - b 0.007 0.010 0.17 0.27 6 b1 0.007 0.009 0.17 0.23 - D 0.350 0.358 8.90 9.10 3 D1 0.272 0.280 6.90 7.10 4, 5 E 0.350 0.358 8.90 9.10 3 E1 0.272 0.280 6.90 7.10 4, 5 L 0.018 0.029 0.45 0.75 - N 48 48 7 e 0.020 BSC 0.50 BSC Rev. 2 1/99 NOTES: 0.08 0.003 -C- 1. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. 2. All dimensions and tolerances per ANSI Y14.5M-1982. 0.08 0.003 M C A-B S 11o-13o 0.020 0.008 MIN b 4. Dimensions D1 and E1 to be determined at datum plane -H- . 0.09/0.16 A2 A1 0.004/0.006 GAGE PLANE 11o-13o 5. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25mm (0.010 inch) per side. 6. Dimension b does not include dambar protrusion. Allowable dambar protrusion shall not cause the lead width to exceed the maximum b dimension by more than 0.08mm (0.003 inch). BASE METAL WITH PLATING L 0o-7o 3. Dimensions D and E to be determined at seating plane -C- . b1 0o MIN 0.25 0.010 D S 0.09/0.20 0.004/0.008 7. “N” is the number of terminal positions. All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 16