LM193, LM293, LM293A LM393, LM393A, LM2903, LM2903V www.ti.com SLCS005X – OCTOBER 1979 – REVISED JULY 2013 Dual Differential Comparators Check for Samples: LM193, LM293, LM293A, LM393, LM393A, LM2903, LM2903V FEATURES DESCRIPTION • • These devices consist of two independent voltage comparators that are designed to operate from a single power supply over a wide range of voltages. Operation from dual supplies also is possible as long as the difference between the two supplies is 2 V to 36 V, and VCC is at least 1.5 V more positive than the input common-mode voltage. Current drain is independent of the supply voltage. The outputs can be connected to other open-collector outputs to achieve wired-AND relationships. • • • • • • • • • Single Supply or Dual Supplies Wide Range of Supply Voltage – Max Rating: 2 V to 36 V – Tested to 30 V: Non-V Devices – Tested to 32 V: V-Suffix Devices Low Supply-Current Drain Independent of Supply Voltage: 0.4 mA (Typ) Per Comparator Low Input Bias Current: 25 nA (Typ) Low Input Offset Current: 3 nA (Typ) (LM139) Low Input Offset Voltage: 2 mV (Typ) Common-Mode Input Voltage Range Includes Ground Differential Input Voltage Range Equal to Maximum-Rated Supply Voltage: ±36 V Low Output Saturation Voltage Output Compatible With TTL, MOS, and CMOS On Products Compliant to MIL-PRF-38535, All Parameters Are Tested Unless Otherwise Noted. On All Other Products, Production Processing Does Not Necessarily Include Testing of All Parameters. The LM193 is characterized for operation from −55°C to 125°C. The LM293 and LM293A are characterized for operation from −25°C to 85°C. The LM393 and LM393A are characterized for operation from 0°C to 70°C. The LM2903 is characterized for operation from −40°C to 125°C. LM193 . . . D OR JG PACKAGE LM293 . . . D, DGK, OR P PACKAGE LM293A . . . DOR DGK PACKAGE LM393, LM393A . . . D, DGK, P, PS, OR PW PACKAGE LM2903 . . . D, DGK, P, PS, OR PW PACKAGE (TOP VIEW) LM193 . . . FK PACKAGE (TOP VIEW) NC 1OUT NC VCC NC 1 1 8 2 7 3 6 4 5 VCC 2OUT 2IN− 2IN+ NC − No internal connection NC 1IN− NC 1IN+ NC 4 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 NC 2OUT NC 2IN− NC NC GND NC 2IN+ NC 3 2 1OUT 1IN− 1IN+ GND 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 1979–2013, Texas Instruments Incorporated LM193, LM293, LM293A LM393, LM393A, LM2903, LM2903V SLCS005X – OCTOBER 1979 – REVISED JULY 2013 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. Symbol (Each Comparator) IN+ OUT IN− Schematic (Each Comparator) VCC 80-µA Current Regulator 10 µA IN+ 60 µA 10 µA 80 µA COMPONENT COUNT OUT Epi-FET Diodes Resistors Transistors 1 2 2 30 IN− GND Current values shown are nominal. 2 Submit Documentation Feedback Copyright © 1979–2013, Texas Instruments Incorporated Product Folder Links: LM193 LM293 LM293A LM393 LM393A LM2903 LM2903V LM193, LM293, LM293A LM393, LM393A, LM2903, LM2903V www.ti.com SLCS005X – OCTOBER 1979 – REVISED JULY 2013 Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) Supply voltage, VCC (2) Differential input voltage, VID (3) Input voltage range (either input), VI Output voltage, VO Output current, IO Duration of output short circuit to ground (4) Package thermal impedance, junction to free air, θJA (5) (6) Package thermal impedance, junction to case, θJC (7) (8) VALUE UNIT 36 V ±36 V –0.3 to 36 V 36 V 20 mA Unlimited D package 97 DGK package 172 P package 85 PS package 95 PW package 149 FK package 5.61 JG package 14.5 Operating virtual-junction temperature, TJ °C/W °C/W 150 °C Case temperature for 60 s FK package 260 °C Lead temperature 1,6 mm (1/16 in) from case for 60 s J package 300 °C –65 to 150 °C Storage temperature range, Tstg (1) (2) (3) (4) (5) (6) (7) (8) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage values, except differential voltages, are with respect to network ground. Differential voltages are at IN+ with respect to IN–. Short circuits from outputs to VCC can cause excessive heating and eventual destruction. Maximum power dissipation is a function of TJ (max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ (max) – TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability. The package thermal impedance is calculated in accordance with JESD 51-7. Maximum power dissipation is a function of TJ (max), θJC, and TC. The maximum allowable power dissipation at any allowable case temperature is PD = (TJ (max) – TC)/θJC. Operating at the absolute maximum TJ of 150°C can affect reliability. The package thermal impedance is calculated in accordance with MIL-STD-883. Copyright © 1979–2013, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LM193 LM293 LM293A LM393 LM393A LM2903 LM2903V 3 LM193, LM293, LM293A LM393, LM393A, LM2903, LM2903V SLCS005X – OCTOBER 1979 – REVISED JULY 2013 www.ti.com Electrical Characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted) PARAMETER TEST CONDITIONS TA (1) MIN VIO Input offset voltage VCC = 5 V to 30 V, VIC = VICR min, VO = 1.4 V IIO Input offset current VO = 1.4 V IIB Input bias current VO = 1.4 V VICR Common-mode input-voltage range (2) AVD Large-signal differential-voltage amplification IOH High-level output current 25°C Full range VCC = 15 V, VO = 1.4 V to 11.4 V, RL ≥ 15 kΩ to VCC 25°C VOH = 5 V VID = 1 V 25°C VOH = 30 V VID = 1 V Full range Low-level output current VOL = 1.5 V, VID = –1 V 25°C VCC = 5 V 25°C VCC = 30 V Full range UNIT TYP MAX 2 5 9 25 5 100 –25 –100 –25 0 to VCC – 1.5 0 to VCC – 2 0 to VCC – 2 200 50 0.1 Full range 400 200 1 2.5 nA V/mV 50 nA 1 μA 150 400 700 6 0.8 nA 0.1 700 6 mV V 1 150 –250 –400 0 to VCC – 1.5 50 50 250 –300 25°C IOL 4 3 25°C VID = –1 V (2) 5 Full range IOL = 4 mA, (1) 2 MIN 9 25°C 25°C RL = ∞ MAX Full range Low-level output voltage Supply current TYP Full range VOL ICC LM293 LM393 LM193 mV mA 0.8 1 2.5 mA Full range (MIN or MAX) for LM193 is –55°C to 125°C, for LM293 is 25°C to 85°C, and for LM393 is 0°C to 70°C. All characteristics are measured with zero common-mode input voltage, unless otherwise specified. The voltage at either input or common-mode should not be allowed to go negative by more than 0.3 V. The upper end of the commonmode voltage range is VCC+ – 1.5 V for the inverting input (–), and the non-inverting input (+) can exceed the VCC level; the comparator provides a proper output state. Either or both inputs can go to 30 V without damage. Submit Documentation Feedback Copyright © 1979–2013, Texas Instruments Incorporated Product Folder Links: LM193 LM293 LM293A LM393 LM393A LM2903 LM2903V LM193, LM293, LM293A LM393, LM393A, LM2903, LM2903V www.ti.com SLCS005X – OCTOBER 1979 – REVISED JULY 2013 Electrical Characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted) PARAMETER TEST CONDITIONS TA (1) LM293A LM393A MIN VIO Input offset voltage VCC = 5 V to 30 V, VO = 1.4 V VIC = VICR(min) IIO Input offset current VO = 1.4 V IIB Input bias current VO = 1.4 V 25°C Common-mode input-voltage range Large-signal differential-voltage amplification IOH High-level output current VOL VCC = 15 V, VO = 1.4 V to 11.4 V, RL ≥ 15 kΩ to VCC –25 25°C VID = 1 V Full range Low-level output voltage IOL = 4 mA, VID = –1 V IOL Low-level output current VOL = 1.5 V, VID = –1 V, 25°C ICC Supply current (four comparators) VCC = 5 V 25°C VCC = 30 V Full range –250 –400 0 to VCC – 1.5 50 200 0.1 25°C mV nA nA V 0 to VCC – 2 25°C VID = 1 V 50 150 25°C VOH = 30 V, (2) 5 Full range VOH = 5 V, (1) 2 4 25°C (2) RL = ∞ 1 Full range Full range AVD MAX Full range 25°C VICR UNIT TYP 150 Full range V/mV 50 nA 1 μA 400 700 6 mV mA 0.8 1 2.5 mA Full range (MIN or MAX) for LM293A is 25°C to 85°C, and for LM393A is 0°C to 70°C. All characteristics are measured with zero common-mode input voltage, unless otherwise specified. The voltage at either input or common-mode should not be allowed to go negative by more than 0.3 V. The upper end of the commonmode voltage range is VCC+ – 1.5 V, but either or both inputs can go to 30 V without damage. Copyright © 1979–2013, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LM193 LM293 LM293A LM393 LM393A LM2903 LM2903V 5 LM193, LM293, LM293A LM393, LM393A, LM2903, LM2903V SLCS005X – OCTOBER 1979 – REVISED JULY 2013 www.ti.com Electrical Characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted) PARAMETER TEST CONDITIONS VIO Input offset voltage VCC = 5 V to MAX (2) , VO = 1.4 V, VIC = VICR(min), IIO Input offset current VO = 1.4 V IIB Input bias current VO = 1.4 V VICR Common-mode inputvoltage range (3) IOH High-level output current 25°C VOH = 5 V, VID = 1 V 25°C VID = 1 V Full range (2) VOH = VCC MAX , IOL Low-level output current VOL = 1.5 V, VID = –1 V 25°C VCC = 5 V 25°C VCC = MAX TYP MAX 1 2 4 50 5 200 –25 –250 –25 0 to VCC – 1.5 0 to VCC – 2 0 to VCC – 2 100 25 0.1 50 150 400 –250 –500 0 to VCC – 1.5 25 50 200 –500 Full range 100 Full range nA 50 nA 1 μA 150 400 700 1 nA V/mV 6 0.8 mV 0.1 700 6 UNIT V 1 25°C VID = –1 V, (2) (3) 5 25°C IOL = 4 mA, (1) 7 Full range VCC = 15 V, VO = 1.4 V to 11.4 V, RL ≥ 15 kΩ to VCC RL = ∞ 2 MIN 15 25°C Low-level output voltage Supply current MAX Full range VOL ICC LM2903A TYP Full range Full range Large-signal differentialvoltage amplification MIN 25°C 25°C AVD LM2903 TA (1) mV mA 0.8 2.5 1 2.5 mA Full range (MIN or MAX) for LM2903 is –40°C to 125°C. All characteristics are measured with zero common-mode input voltage, unless otherwise specified. VCC MAX = 30 V for non-V devices and 32 V for V-suffix devices. The voltage at either input or common-mode should not be allowed to go negative by more than 0.3 V. The upper end of the commonmode voltage range is VCC+ – 1.5 V, but either or both inputs can go to 30 V (32 V for V-suffix devices) without damage. Switching Characteristics VCC = 5 V, TA = 25°C PARAMETER LM2901, LM293, LM293A LM393, LM393A LM2903 TEST CONDITIONS UNIT TYP Response time (1) (2) 6 RL connected to 5 V through 5.1 kΩ, CL = 15 pF (1) (2) 100-mV input step with 5-mV overdrive 1.3 TTL-level input step 0.3 μs CL includes probe and jig capacitance. The response time specified is the interval between the input step function and the instant when the output crosses 1.4 V. Submit Documentation Feedback Copyright © 1979–2013, Texas Instruments Incorporated Product Folder Links: LM193 LM293 LM293A LM393 LM393A LM2903 LM2903V LM193, LM293, LM293A LM393, LM393A, LM2903, LM2903V www.ti.com SLCS005X – OCTOBER 1979 – REVISED JULY 2013 REVISION HISTORY Changes from Revision W (July 2010) to Revision X Page • Updated document to new TI data sheet format - no specification changes. ...................................................................... 1 • Updated Features. ................................................................................................................................................................ 1 • Added ESD warning. ............................................................................................................................................................ 2 • Removed Ordering Information table. ................................................................................................................................... 2 Copyright © 1979–2013, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LM193 LM293 LM293A LM393 LM393A LM2903 LM2903V 7 PACKAGE MATERIALS INFORMATION www.ti.com 28-Jan-2014 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LM193DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 LM2903DGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LM2903DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 LM2903DR SOIC D 8 2500 330.0 12.8 6.4 5.2 2.1 8.0 12.0 Q1 LM2903DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 LM2903DRG3 SOIC D 8 2500 330.0 12.8 6.4 5.2 2.1 8.0 12.0 Q1 LM2903DRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 LM2903DRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 LM2903PSR SO PS 8 2000 330.0 16.4 8.2 6.6 2.5 12.0 16.0 Q1 LM2903PWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1 LM2903PWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1 LM2903PWRG3 TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1 LM2903QDRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 LM2903VQPWRG4 TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1 LM293ADGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LM293ADR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 LM293ADR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 LM293ADRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 28-Jan-2014 Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LM293ADRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 LM293DGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LM293DR SOIC D 8 2500 330.0 12.8 6.4 5.2 2.1 8.0 12.0 Q1 LM293DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 LM293DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 LM293DRG3 SOIC D 8 2500 330.0 12.8 6.4 5.2 2.1 8.0 12.0 Q1 LM293DRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 LM293DRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 LM393ADGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LM393ADR SOIC D 8 2500 330.0 12.8 6.4 5.2 2.1 8.0 12.0 Q1 LM393ADR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 LM393ADR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 LM393ADRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 LM393ADRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 LM393APSR SO PS 8 2000 330.0 16.4 8.2 6.6 2.5 12.0 16.0 Q1 LM393APWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1 LM393DGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LM393DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 LM393DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 LM393DRG3 SOIC D 8 2500 330.0 12.8 6.4 5.2 2.1 8.0 12.0 Q1 LM393DRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 LM393DRG4 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 LM393PSR SO PS 8 2000 330.0 16.4 8.2 6.6 2.5 12.0 16.0 Q1 LM393PWR TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1 LM393PWRG3 TSSOP PW 8 2000 330.0 12.4 7.0 3.6 1.6 8.0 12.0 Q1 Pack Materials-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 28-Jan-2014 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM193DR SOIC D 8 2500 367.0 367.0 35.0 LM2903DGKR VSSOP DGK 8 2500 364.0 364.0 27.0 LM2903DR SOIC D 8 2500 340.5 338.1 20.6 LM2903DR SOIC D 8 2500 364.0 364.0 27.0 LM2903DR SOIC D 8 2500 367.0 367.0 35.0 LM2903DRG3 SOIC D 8 2500 364.0 364.0 27.0 LM2903DRG4 SOIC D 8 2500 340.5 338.1 20.6 LM2903DRG4 SOIC D 8 2500 367.0 367.0 35.0 LM2903PSR SO PS 8 2000 367.0 367.0 38.0 LM2903PWR TSSOP PW 8 2000 367.0 367.0 35.0 LM2903PWR TSSOP PW 8 2000 364.0 364.0 27.0 LM2903PWRG3 TSSOP PW 8 2000 364.0 364.0 27.0 LM2903QDRG4 SOIC D 8 2500 367.0 367.0 35.0 LM2903VQPWRG4 TSSOP PW 8 2000 367.0 367.0 35.0 LM293ADGKR VSSOP DGK 8 2500 364.0 364.0 27.0 LM293ADR SOIC D 8 2500 340.5 338.1 20.6 LM293ADR SOIC D 8 2500 367.0 367.0 35.0 LM293ADRG4 SOIC D 8 2500 340.5 338.1 20.6 LM293ADRG4 SOIC D 8 2500 367.0 367.0 35.0 LM293DGKR VSSOP DGK 8 2500 364.0 364.0 27.0 Pack Materials-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 28-Jan-2014 Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM293DR SOIC D 8 2500 364.0 364.0 27.0 LM293DR SOIC D 8 2500 367.0 367.0 35.0 LM293DR SOIC D 8 2500 340.5 338.1 20.6 LM293DRG3 SOIC D 8 2500 364.0 364.0 27.0 LM293DRG4 SOIC D 8 2500 367.0 367.0 35.0 LM293DRG4 SOIC D 8 2500 340.5 338.1 20.6 LM393ADGKR VSSOP DGK 8 2500 364.0 364.0 27.0 LM393ADR SOIC D 8 2500 364.0 364.0 27.0 LM393ADR SOIC D 8 2500 367.0 367.0 35.0 LM393ADR SOIC D 8 2500 340.5 338.1 20.6 LM393ADRG4 SOIC D 8 2500 367.0 367.0 35.0 LM393ADRG4 SOIC D 8 2500 340.5 338.1 20.6 LM393APSR SO PS 8 2000 367.0 367.0 38.0 LM393APWR TSSOP PW 8 2000 364.0 364.0 27.0 LM393DGKR VSSOP DGK 8 2500 364.0 364.0 27.0 LM393DR SOIC D 8 2500 367.0 367.0 35.0 LM393DR SOIC D 8 2500 340.5 338.1 20.6 LM393DRG3 SOIC D 8 2500 364.0 364.0 27.0 LM393DRG4 SOIC D 8 2500 367.0 367.0 35.0 LM393DRG4 SOIC D 8 2500 340.5 338.1 20.6 LM393PSR SO PS 8 2000 367.0 367.0 38.0 LM393PWR TSSOP PW 8 2000 364.0 364.0 27.0 LM393PWRG3 TSSOP PW 8 2000 364.0 364.0 27.0 Pack Materials-Page 4 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2014, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LM393ADR LM393PWR LM393AP LM393AD LM393APWR LM393PSR LM393DR LM193DR LM2903DR LM2903PWR LM2903D LM2903P LM293D LM293P LM393D LM393P LM293AD LM293DR LM2903QD LM2903AVQDR LM2903AVQPWR LM2903DE4 LM2903DG4 LM2903DGKR LM2903DGKRG4 LM2903DRE4 LM2903DRG4 LM2903PE4 LM2903PSR LM2903PSRG4 LM2903PWRE4 LM2903PWRG4 LM2903VQDR LM2903VQPWR LM293ADE4 LM293ADG4 LM293ADGKR LM293ADGKRG4 LM293ADR LM293ADRE4 LM293ADRG4 LM293DE4 LM293DG4 LM293DGKR LM293DGKRG4 LM293DRE4 LM293DRG4 LM293PE4 LM393ADE4 LM393ADG4 LM393ADGKR LM393ADGKRG4 LM393ADRE4 LM393ADRG4 LM393APE4 LM393APSR LM393APSRE4 LM393APWRE4 LM393DE4 LM393DG4 LM393DGKR LM393DRE4 LM393DRG4 LM393PE4 LM393PSRG4 LM393PW LM393PWE4 LM393PWRE4 LM393PWRG4 LM393APSRG4 LM193DRG4 LM2903AVQDRG4 LM2903AVQPWRG4 LM2903QDG4 LM2903QDRG4 LM2903VQDRG4 LM2903VQPWRG4 LM393DGKRG4 LM393PWG4 LM393APWRG4 LM2903DRG3 LM393DRG3 LM393PE3 LM2903PWRG3 LM293DRG3 LM393PWRG3