DD21 Power entry modules without line filter https://www.schurter.com /PG05 IEC Appliance Inlet C14 with Line Switch 2-pole, Fuseholder 1- or 2-pole, for PCB mounting, Order required accessories separately C14 See below: Approvals and Compliances 70° C Description - Panel Mount : Screw-on mounting on PCB/Panel backside with screws M3 - 3 Functions : Appliance Inlet Protection class I , Line Switch 2-pole , Fuseholder for fuse-links 5 x 20 mm 1‑ or 2‑pole - V-Lock notch standard - Meets the requirements of IEC 60335-1 for appliances in unattended use. This includes the enhanced requirements of glow wire tests acc. to IEC 60695-2-12 and -13. - PCB terminals - With cover on rear-side Characteristics - Ultra-compact design. Ideal for low profile designs All single elements are already wired For added safety "Extra-Safe" fuse drawers are available Ideal for application with high transient loads Suitable for use in equipment according to IEC/UL 60950 Other versions on request - Fixing on PCB with self-tapping screws 3 mm or pre-inserted nuts M3 Fuse drawer 1-pole, plus spare fuse case Fuse drawer 2-pole, with shorting bar Other rocker marking Line switch 1-pole Protection class II, 70°C Without cover References Alternative: version with line filter DD22 Alternative: version for panel mounting DD11 Weblinks pdf datasheet, html-datasheet, General Product Information, DistributorStock-Check, Accessories, Detailed request for product, Microsite Technical Data Ratings IEC Ratings UL/CSA Dielectric Strength Allowable Operation Temperature IP-Protection Insulation cover Terminal Panel Thickness S Material: Housing 1) 10 A / 250 VAC; 50 Hz 10 A / 125 VAC; 60 Hz ¹⁾ > 2.5 kVAC between L-N > 3 kVAC between L/N-PE (1 min/50 Hz) -25 °C to 85 °C appliance inlet/-outlet from front side IP 40 acc. to IEC 60529 Suitable for appliances with protection class I or II acc. to IEC 61140 For PCB mounting 3 mm, Ground terminal, additional quick connect 4.8 x 0.8 mm Screw-on mounting: max 3 mm Mounting screw torque max 0.5 Nm Thermoplastic, black, UL 94V-0 Rated Power Acceptance @ Ta 23 °C Power Acceptance @ Ta > 23°C Fuseholder Line Switch C14 acc. to IEC 60320-1 UL 498, CSA C22.2 no. 42 (for cold conditions) pin-temperature 70 °C, 10 A, Protection Class I 1 or 2 pole, Shocksafe category PC2 acc. to IEC 60127-6, for fuse-links 5 x 20 mm 5 x 20: 2 W (1 pole)/ 1.6 W (2-pole) per pole Admissible power acceptance at higher ambient temperature see derating curves Rocker switch 2-pole, non-illuminated or illuminated, acc. to IEC 61058-1 Technical Details with cover 8 A, without cover 10 A Approvals and Compliances Detailed information on product approvals, code requirements, usage instructions and detailed test conditions can be looked up in Details about Approvals Connectors 1 DD21 Power entry modules without line filter https://www.schurter.com /PG05 Approvals The approval mark is used by the testing authorities to certify compliance with the safety requirements placed on electronic products. Approval Reference Type: DD21 Approval Logo Certificates Certification Body Description VDE Approvals VDE Certificate Number: 40018283 UL Approvals UL UL File Number: E93617 Design Standard Description Designed according to IEC 60320-1 Appliance couplers for household and similar general purposes Designed according to IEC 60127-6 Miniature fuses. Part 6. Fuse-holders for miniature fuse-links Designed according to IEC 61058-1 Switches for appliances. Part 1. General requirements Designed according to UL 498 Standard for Attachment Plugs and Receptacles Designed according to CSA C22.2 no. 42 General Use Receptacles, Attachment Plugs, and Similar Wiring Devices Design Standard Description Designed for applications acc. IEC/UL 60950 IEC 60950-1 includes the basic requirements for the safety of information technologyequipment. Designed for applications acc. IEC 60601-1 Medical electrical equipment - Part 1: General requirements for basic safety and essential performance Designed for applications acc. IEC 60335-1 Safety of electrical appliances for household and similar purposes. Meets the requirements for appliances in unattended use. This includes the enhanced requirements of glow wire tests acc. to IEC 60695-2-12 and -13. Details Initiator Description CE declaration of conformity SCHURTER AG The CE marking declares that the product complies with the applicable requirements laid down in the harmonisation of Community legislation on its affixing in accordance with EU Regulation 765/2008. RoHS SCHURTER AG EU Directive RoHS 2011/65/EU China RoHS SCHURTER AG The law SJ / T 11363-2006 (China RoHS) has been in force since 1 March 2007. It is similar to the EU directive RoHS. REACH SCHURTER AG On 1 June 2007, Regulation (EC) No 1907/2006 on the Registration, Evaluation, Authorization and Restriction of Chemicals 1 (abbreviated as "REACH") entered into force. MicrositeV-Lock SCHURTER AG V-Lock system are based on a matching plug-dose combination. The connector is equipped with a notch intended for use with the latching cordset. The cord latching system prevents against accidental removal of the cordset. Medical Equipment SCHURTER AG Suitable for use in medical equipment according to IEC/UL 60601-1 Product standards Product standards that are referenced Organization Application standards Application standards where the product can be used Organization Compliances The product complies with following Guide Lines Identification 2 Connectors DD21 Power entry modules without line filter https://www.schurter.com /PG05 Dimensions [mm] Screw version 65 3.5 34.6 46.7 2.5 1.5 33 1. 85 10.3 6 29.2 2.5 3.15 1.25 0.8 3. ±0 2 47.1±0.10 19.05 10.45 R 28.1 ±0.10 27.1 32.3 27.2 17 4.5 0.95 6 2) .0 5 R 1) 3.4 56 ±0.15 56 46.6 3.2 6 ±0.10 24.4 4 3. 39.65 ±0.15 +0 0 .10 .10 0 +0 1.6 1.3 3.6 +0 0 .10 3.6 9.5 4.5 5 1.3 9.55 ±0.10 32.4 10.45 ±0.10 56 ±0.15 1) with cover 2) without cover For grounding additional quick connect terminal 4.8 x 0.8 mm Diagrams non-illuminated illuminated PE'' PE'' 1) L F1 PE N 1) Line 2) Load S L' 2) PE' F2 N' 1) L F1 PE N F2 L' S R 2) PE' N' 1) Line 2) Load Connectors 3 DD21 Power entry modules without line filter https://www.schurter.com /PG05 Derating Curves 1-pole 2-pole 1.5 I = 1.0 In I = 0.7 In 1.0 I = << In 0.5 0.0 0 20 40 60 80 1.6 Admissible power acceptance in Watt per pole Admissible power acceptance in Watt 2.0 100 Ambient air temperature Ta °C 1.4 1.2 I = 1.0 In 1.0 0.8 I = 0.7 In 0.6 I = < < In 0.4 0.2 0.0 0 20 40 60 80 100 Ambient air temperature Ta °C All Variants Fuseholder Line Switch Illumination Color Cover 1-pole 2-pole non-illuminated - DD21.0111.1111 1-pole 2-pole illuminated red DD21.0113.1111 1-pole 2-pole illuminated green DD21.0114.1111 2-pole 2-pole non-illuminated - DD21.0121.1111 █ 2-pole 2-pole non-illuminated - DD21.0121.1110 █ 2-pole 2-pole illuminated red DD21.0123.1111 2-pole 2-pole illuminated green DD21.0124.1111 l Order Number █ █ UL approvals: versions without cover are approved for 10 A, and can be ordered with "0" as last digit of the order number (e.g. DD21. xxxx.xxx0) █ Most Popular. Availability for all products can be searched real-time:https://www.schurter.com/en/Stock-Check/Stock-Check-SCHURTER Packaging unit 40 Pcs Required Accessory Description Fusedrawer 2 Fusedrawer für Fuse Links 5x20 mm, with or without Voltage Selector Insert Fingergrip, 2-pole 4301.1401 Extra-Safe, 2-pole 4301.1403 Fingergrip, 1-pole 4301.1405 Extra-Safe, 1-pole 4301.1407 ... Mating Outlets/Connectors Category / Description Appliance Outlet Overview complete IEC Appliance Outlet F, Screw-on Mounting, Front Side, Solder Terminal 4787 IEC Appliance Outlet F, Snap-in Mounting, Front Side, Solder or Quick-connect Terminal 4788 IEC Appliance Outlet F or H, Screw-on Mounting, Front Side, Solder, PCB or Quick-connect Terminal 5091 Appliance Outlet further types to DD21 4 Connectors DD21 Power entry modules without line filter https://www.schurter.com /PG05 Connector Overview complete 4782 Mounting: Power Cord, 3 x 1 mm² / 3 x 18 AWG, Cable, Connector: IEC C13 4782 4022 Mounting: Power Supply Cord, 3 x 1.5 mm², Screw clamps, Connector: IEC C13 4022 4785 Mounting: Power Cord, 3 x 1 mm² / 3 x 18 AWG, Cable, Connector: IEC C13 4785 4300-06 Mounting: Power Cord, 3 x 1 mm² / 3 x 18 AWG, Cable, Connector: IEC C13 4300-06 4012 Mounting: Power Supply Cord, 3 x 1.5 mm², Screw clamps, Connector: IEC C13 4012 Connector further types to DD21 ... Mating Outlets/Connectors shuttered Power Cord Overview complete VAC13KS, Overview, diverse Connector IEC C13, cord end: VAC13KS Power cord with IEC connector C17, V-Lock, straight VAC17KS 16.02.2018 Power Cord further types to DD21 The specifications, descriptions and illustrations indicated in this document are based on current information. All content is subject to modifications and amendments. Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability and test each product selected for their own applications. Connectors 5