AD AD6654CBC 14-bit, 92.16 msps, 4-/6-channel wideband if to baseband receiver Datasheet

14-Bit, 92.16 MSPS, 4-/6-Channel
Wideband IF to Baseband Receiver
AD6654
FEATURES
APPLICATIONS
SNR = 90 dB in 1.25 MHz bandwidth to Nyquist
SNR = 87 dB in 1.25 MHz bandwidth to 200 MHz
Integrated 14-bit, 92.16 MSPS ADC
IF sampling frequencies to 200 MHz
Internal 2.4 V reference, 2.2 V p-p analog input range
Internal differential track-and-hold analog input
Processes 4/6 wideband carriers simultaneously
Fractional clock multiplier to 200 MHz
Programmable decimating FIR filters, interpolating
half-band filters and programmable AGC loops
with 96 dB range
Three 16-bit configurable parallel output ports
User-configurable built-in self-test (BIST) capability
8-/16-bit microport and SPORT/SPI® serial port control
Multicarrier, multimode digital receivers
GSM, EDGE, PHS, UMTS, WCDMA, CDMA2000,
TD-SCDMA, WiMAX
Micro and pico cell systems, software radios
Wireless local loop
Smart antenna systems
In-building wireless telephony
Broadband data applications
Instrumentation and test equipment
FUNCTIONAL BLOCK DIAGRAM
FIR1
HB1
M = BYP, 2
FIR2
HB2
M = BYP, 2
MRCF
DRCF
M = 1–16
CRCF
M = 1–16
LHB
L = 1, 2
NCO
CIC5
M = 1–32
FIR1
HB1
M = BYP, 2
FIR2
HB2
M = BYP, 2
MRCF
DRCF
M = 1–16
SHA
ADC
CRCF
M = 1–16
LHB
L = 1, 2
NCO
CIC5
M = 1–32
FIR1
HB1
M = BYP, 2
FIR2
HB2
M = BYP, 2
MRCF
DRCF
M = 1–16
CRCF
M = 1–16
LHB
L = 1, 2
NCO
CIC5
M = 1–32
FIR1
HB1
M = BYP, 2
FIR2
HB2
M = BYP, 2
MRCF
DRCF
M = 1–16
CRCF
M = 1–16
LHB
L = 1, 2
NCO
CIC5
M = 1–32
FIR1
HB1
M = BYP, 2
FIR2
HB2
M = BYP, 2
MRCF
DRCF
M = 1–16
CRCF
M = 1–16
LHB
L = 1, 2
NCO
CIC5
M = 1–32
FIR1
HB1
M = BYP, 2
FIR2
HB2
M = BYP, 2
MRCF
DRCF
M = 1–16
CRCF
M = 1–16
LHB
L = 1, 2
INPUT
MATRIX
2.4V
VREF
PRN
GEN
OVR
(ADC OVERRANGE)
EXP
(VGA LEVEL CONTROL)
3
EXP
BITS
PEAK/
RMS
MSMT
(AVAILABLE IN
6-CHANNEL MODEL ONLY)
M = DECIMATION
L = INTERPOLATION
AVDD, DRVDD,
VDDCORE, VDDIO, GND
SYNC
0, 1, 2, 3
CLOCK
MULTIPLIER
AGC
8-BIT/16-BIT MICROPORT
INTERFACE
PARALLEL PORTS
14
AIN–
VREF
CIC5
M = 1–32
SPORT/
SPI INTERFACE
PA
PB
PC
05156-001
ENC–
AIN+
NCO
INTERNAL
TIMING
DATA ROUTER MATRIX
ENC+
DATA ROUTING
4-CHANNEL AND 6-CHANNEL DIGITAL DOWN CONVERTER
14-BIT ADC FRONT END
Figure 1.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2005 Analog Devices, Inc. All rights reserved.
AD6654
TABLE OF CONTENTS
General Description ......................................................................... 4
Input Crossbar Matrix ............................................................... 33
Product Highlights ....................................................................... 5
Numerically Controlled Oscillator (NCO) ................................. 34
Specifications..................................................................................... 6
NCO Frequency.......................................................................... 34
Recommended Operating Conditions ...................................... 6
Mixer............................................................................................ 35
ADC DC Specifications ............................................................... 6
Bypass .......................................................................................... 35
ADC Digital Specifications ......................................................... 6
Clear Phase Accumulator on Hop ........................................... 35
ADC Switching Specifications.................................................... 7
Phase Dither................................................................................ 35
ADC AC Specifications ............................................................... 7
Amplitude Dither ....................................................................... 35
Electrical Characteristics............................................................. 8
NCO Frequency Hold-Off Register......................................... 35
Timing Characteristics ................................................................ 9
Phase Offset................................................................................. 35
Microport Timing Characteristics ........................................... 10
HOP Sync .................................................................................... 35
Serial Port Timing Characteristics ........................................... 11
Fifth-Order CIC Filter ................................................................... 36
Timing Diagrams............................................................................ 12
Bypass .......................................................................................... 36
Absolute Maximum Ratings.......................................................... 18
CIC Rejection.............................................................................. 36
Thermal Characteristics ............................................................ 18
Example Calculations ................................................................ 37
Explanation of Test Levels ......................................................... 18
FIR Half-Band Block...................................................................... 38
ESD Caution................................................................................ 18
3-Tap Fixed coefficient Filter (FIR1) ....................................... 38
Pin Configuration and Function Descriptions........................... 19
Decimate-by-2 Half-Band Filter (HB1) .................................. 38
Typical Performance Characteristics ........................................... 22
6-Tap Fixed Coefficient Filter (FIR2) ...................................... 39
ADC Equivalent Circuits............................................................... 25
Decimate-by-2 Half-Band Filter (HB2) .................................. 39
Terminology .................................................................................... 26
Intermediate Data Router.............................................................. 41
Theory of Operation ...................................................................... 27
Mono-Rate RAM Coefficient Filter (MRCF) ............................. 42
ADC Architecture ...................................................................... 27
Symmetry .................................................................................... 42
Application information ................................................................ 28
Clock Rate ................................................................................... 42
ADC Configuration Notes ........................................................ 28
Bypass .......................................................................................... 42
DDC Configuration Notes ........................................................ 29
Scaling.......................................................................................... 42
ADC Input Port Monitor Function.............................................. 31
Decimating RAM Coefficient Filter (DRCF) ............................. 43
Peak Detector Mode................................................................... 31
Bypass .......................................................................................... 43
Mean Power Mode ..................................................................... 31
Scaling.......................................................................................... 43
Threshold Crossing Mode......................................................... 32
Symmetry .................................................................................... 43
Additional Control Bits ............................................................. 32
Coefficient Offset ....................................................................... 43
Rev. 0 | Page 2 of 88
AD6654
Decimation Phase .......................................................................43
HOP ..............................................................................................58
Maximum Number of Taps Calculated....................................43
Serial Port Control ..........................................................................60
Programming DRCF Registers for
an Asymmetrical Filter ...............................................................44
Hardware Interface .....................................................................60
Programming DRCF Registers for a Symmetric Filter ..........44
Channel RAM Coefficient Filter (CRCF) ....................................45
SPI Mode Timing........................................................................62
SPORT Mode Timing.................................................................64
Bypass ...........................................................................................45
Programming Indirect Addressed Registers
Using Serial Port..........................................................................67
Scaling...........................................................................................45
Connecting the AD6654 Serial Port to a Blackfin DSP .........69
Symmetry .....................................................................................45
Microport .........................................................................................70
Coefficient Offset ........................................................................45
Intel (Inm) Mode ........................................................................70
Decimation Phase .......................................................................45
Motorola (MNM) Mode ............................................................70
Maximum Number of TAPS Calculated..................................45
Accessing Multiple AD6654 Devices .......................................71
Programming CRCF Registers for an
Asymmetrical Filter ....................................................................46
Memory Map ...................................................................................72
Programming CRCF Registers for a Symmetrical Filter .......46
Interpolating Half-Band Filter.......................................................47
Output Data Router ........................................................................48
Interleaving Data.........................................................................48
Automatic Gain Control.................................................................49
AGC Loop ....................................................................................49
Desired Signal Level Mode ........................................................50
Desired Clipping Level Mode....................................................52
AGC Synchronization.................................................................52
SYNC Process ..............................................................................52
Parallel Port Output ........................................................................53
Interleaved I/Q Mode .................................................................53
Reading the Memory Map Table...............................................72
Bit Format ....................................................................................72
Open Locations ...........................................................................72
Default Values..............................................................................72
Logic Levels..................................................................................72
Global Register Map ...................................................................74
Input Port Register Map.............................................................76
Channel Register Map ................................................................78
MRCF Coefficient Memory.......................................................79
Output Port Register Map..........................................................82
DDC Design Notes .........................................................................85
Outline Dimensions........................................................................87
Ordering Guide ...........................................................................87
Parallel IQ Mode .........................................................................53
Master/Slave PCLK Modes ........................................................55
Parallel Port Pin Functions ........................................................56
REVISION HISTORY
4/05—Revision 0: Initial Version
User-Configurable Built-In Self-Test (BIST)...............................57
Chip Synchronization .....................................................................58
Start ...............................................................................................58
Rev. 0 | Page 3 of 88
AD6654
GENERAL DESCRIPTION
The AD6654 is a mixed-signal IF-to-baseband receiver
consisting of a 14-bit, 92.16 MSPS analog-to-digital converter
(ADC) and a 4-/6-channel, multimode digital down-converter
(DDC) capable of processing up to six WCDMA (wideband
code division multiple access) channels. The AD6654 has been
optimized for the demanding filtering requirements of wideband standards such as CDMA2000, UMTS, and TD-SCDMA,
but is flexible enough to support wider standards such as
WiMAX. It is typically used as part of a radio system that
digitally demodulates and filters IF sampled signals.
The ADC stage features a high performance track-and-hold
input amplifier (T/H), integrated voltage reference, and 14-bit
sampling resolution. Input signals up to 200 MHz can be
accurately digitized at encode rates up to 92.16 MSPS. The ADC
data outputs are internally routed directly into the DDC inputs,
where down-conversion, decimation and digital filtering are
performed. An overrange (OVR) output bit provides indication
of excessive ADC input levels. An ADC data-ready (DR) output
bit provides a synchronized clock for the integrated DDC.
Data from the ADC is evaluated for peak or mean power in the
input stage of the DDC, and the result is available to the user via
control register access. The DDC input stage also outputs 3-bit
level-indicator data (EXP) bits that can be used to control the
gain of the external DVGA in 6 dB steps (up to 48 dB) to
optimize signal amplitude into the ADC input.
The DDC stage has the following signal processing stages: six
WCDMA-ready channels, each consisting of a frequency
translator, a fifth-order cascaded integrated comb filter, two sets
of cascaded fixed coefficient FIR and half-band filters, three
cascaded programmable sum of product FIR filters, an
interpolating half-band filter (IHB), and a digital automatic
gain control (AGC) block. Multiple modes are supported for
clocking data out of the chip. Programming is accomplished via
serial or microport interfaces.
Frequency translation is accomplished with a 32-bit complex
numerically controlled oscillator (NCO). The NCO has greater
than 110 dBc SDFR. This stage translates a real input signal
from an intermediate frequency (IF) to a baseband complex
digital output. Phase and amplitude dither can be enabled onchip to improve spurious performance of the NCO. A 16-bit
phase-offset word is available to create a known phase relationship between multiple AD6654 chips or channels. The NCO can
also be bypassed.
Following frequency translation is a fifth-order CIC filter with a
programmable decimation between 1 and 32. This filter is used
to efficiently lower the sample rate, while providing sufficient
alias rejection at frequencies at higher offsets from the signal
of interest.
Following the CIC5 are two sets of filters. Each filter set
includes a nondecimating FIR filter and a decimate-by-2 halfband filter. The FIR1 filter provides about 30 dB of rejection,
while the HB1 provides about 77 dB of rejection. These two sets
of filters can be used together to achieve a 107 dB stop-band
alias rejection, or they can be individually bypassed to save
power.
The FIR2 filter provides about 30 dB of rejection, while the HB2
filter provides about 65 dB of rejection. The filters can be used
together to achieve more than 95 dB stop-band alias rejection,
or they can be individually bypassed to save power. FIR1 and
HB1 filters can run at the maximum ADC data port rate. In
contrast, FIR2 and HB2 can run with a maximum input rate of
75 MSPS (input rate to FIR2 and HB2 filters).
The programmable filtering is divided into three cascaded RAM
coefficient filters (RCFs) for flexible and power-efficient
filtering. The first filter in the cascade is the MRCF, consisting
of a programmable nondecimating FIR. It is followed by
programmable FIR filters (DRCF) with decimation from 1 to
16. They can be used either together to provide high rejection
filters, or independently to save power. The maximum input
rate to the MRCF is one-fourth the PLL clock rate.
The CRCF (Channel RCF) is the last programmable FIR filter
with programmable decimation from 1 to 16. It is typically used
to meet the spectral mask requirements for the air standard of
interest. This could be an RRC, antialiasing filter or any other
real data filter. Decimation in preceding blocks is used to keep
the input rate of this stage as low as possible for the best filter
performance.
The last filter stage in the chain is an interpolate-by-2 half-band
filter, which is used to up-sample the CRCF output to produce
higher output oversampling. Signal rejection requirements for
this stage are relaxed, because preceding filters have already
filtered the blockers and adjacent carriers.
The DDC input port of the AD6654 has its own clock input
used for latching the input data, as well as for providing the
input for an onboard PLL clock multiplier. The output of the
PLL clock is used for processing all filters and processing blocks
beyond the data router following CIC filter. The PLL clock can
be programmed to have a maximum clock rate of 200 MHz.
Typically, the DDC input clock is driven directly from the
integrated ADC’s data-ready (DR) output to ensure proper
synchronization.
A data routing block is used to distribute data from the CICs to
the various channel filters. This block allows multiple back-end
filter chains to work together to process high bandwidth signals
or to make even sharper filter transitions than a single channel
Rev. 0 | Page 4 of 88
AD6654
can perform. It can also allow complex filtering operations to be
achieved in the programmable filters.
The digital AGC provides the user with scaled digital outputs
based on the rms level of the signal present at the output of the
digital filters. The user can set the requested level and time
constant of the AGC loop for optimum performance of the
postprocessor. This is a critical function in the base station for
CDMA application, where the power level must be well
controlled going into the RAKE receivers. It has programmable
clipping and rounding control to provide different output
resolutions.
The overall filter response for the AD6654 is the composite of
all the combined filter stages. Each successive filter stage is
capable of narrower transition bandwidths, but requires a
greater number of CLK cycles to calculate the output. The
AD6654 features a fractional clock multiplier that uses the ADC
clock (which is slower than the DDC’s processing speed) to
produce a DDC master clock up to 200 MHz. This feature
allows fractional multiplication of the input clock to allow the
DDC to function at maximum speed while maintaining edge
identity to the ADC clock.
More decimation in the first filter stage minimizes overall
power consumption. Data from the device is interfaced to a
DSP/FPGA/baseband processor via high speed parallel ports
(preferred), or a DSP-compatible microprocessor interface.
The AD6654 is available in 4-channel and 6-channel versions.
The primary focus of the data sheet is on the 6-channel part.
The only difference between the 6-channel and 4-channel
devices is that, on the 4-channel version, Channel 4 and
Channel 5 are not available (see Figure 1). The 4-channel device
has the same DDC input port features, output ports, and
memory map as the 6-channel device. On the 4-channel
version, the memory map section for Channel 4 and Channel 5
can be programmed and read back, but the two extra channels
are disabled internally.
PRODUCT HIGHLIGHTS
1.
Integrated 14-bit, 92.16 MSPS ADC.
2.
Track-and-hold amplifier analog input for excellent IF
sampling up to 200 MHz.
3.
Four or six independent digital filtering channels.
4.
RMS/peak power monitoring of the ADC data port and
96 dB range AGCs before the output ports.
5.
Three programmable RAM coefficient filters, three halfband filters, two fixed coefficient filters, and one fifthorder CIC filter per channel.
6.
Complex filtering by combining filtering capability of
multiple channels.
7.
Three 16-bit parallel output ports operating at up to
200 MHz clock.
8.
Blackfin®- and TigerSHARC®-compatible, 8-/16-bit
microprocessor port.
9.
Synchronous serial communications port is compatible
with most serial interface standards: SPORT, SPI, and SSR.
Rev. 0 | Page 5 of 88
AD6654
SPECIFICATIONS
RECOMMENDED OPERATING CONDITIONS
Table 1.
Parameter (Conditions)
AVDD1
DRVDD2
VDDCORE
VDDIO2
TAMBIENT
Temp
Full
Full
Full
Full
1
Specified for dc supplies with linear rise-time <250 ms.
2
DRVDD and VDDIO can be operated from the same supply.
Test Level
IV
IV
IV
IV
IV
Min
4.75
3.0
1.65
3.0
−25
Typ
5.0
3.3
1.8
3.3
+25
Max
5.25
3.6
1.95
3.6
+85
Unit
V
V
V
V
°C
ADC DC SPECIFICATIONS
AVDD = 5.0 V, DRVDD = 3.3 V, VDDCORE = 1.8 V, VDDIO = 3.3 V, maximum rated sample rate, differential ENC and AIN, unless
otherwise noted.
Table 2.
Parameter (Conditions)
RESOLUTION
INTERNAL VOLTAGE REFERENCE (VREF)1
Output Voltage
ANALOG INPUTS
Differential Input Voltage Range
Differential Input Capacitance
Differential Input Resistance
Power Supply Rejection (PSRR)
1
Temp
Full
Test Level
IV
Min
Typ
14
Max
Unit
Bits
Full
IV
2.4
V
Full
Full
Full
25°C
IV
V
V
V
2.2
1.5
1
±1.0
V p-p
pF
kΩ
mV/V
VREF is provided for setting the common-mode offset of a differential amplifier such as the AD8138 when a dc-coupled analog input is required. VREF should be buffered
if used to drive additional circuit functions.
ADC DIGITAL SPECIFICATIONS
AVDD = 5.0 V, DRVDD = 3.3 V, VDDCORE = 1.8 V, VDDIO = 3.3 V, maximum rated sample rate, differential ADC input, unless
otherwise noted.
Table 3.
Parameter (Conditions)
ENCODE INPUTS (ENC+, ENC−)
Differential Input Voltage
Differential Input Resistance
Differential Input Capacitance
Temp
Test Level
Min
Full
25°C
25°C
IV
V
V
0.4
Rev. 0 | Page 6 of 88
Typ
10
2.5
Max
Unit
V p-p
kΩ
pF
AD6654
ADC SWITCHING SPECIFICATIONS
AVDD = 5.0 V, DRVDD = 3.3 V, VDDCORE = 1.8 V, VDDIO = 3.3 V, maximum rated sample rate, differential input, unless
otherwise noted.
Table 4.
Parameter (Conditions)
SWITCHING PERFORMANCE
Maximum Conversion Rate
Minimum Conversion Rate
ENC Pulse Width High1 (tENCH)
ENC Pulse Width Low1 (tENCL)
1
Temp
Test Level
Min
Full
Full
Full
Full
II
IV
IV
IV
92.16
Typ
Max
Unit
MSPS
MSPS
ns
ns
30
5.154
5.154
5.425
5.425
Several internal timing parameters are a function of tENCL and tENCH, optimum performance will be achieved with 50/50 duty cycle.
ADC AC SPECIFICATIONS
AVDD = 5.0 V, DRVDD = 3.3 V, VDDCORE = 1.8 V, VDDIO = 3.3 V, maximum rated sample rate, differential input, unless
otherwise noted.
Table 5.
Parameter (Conditions)
SIGNAL-TO-NOISE RATIO1 (WITHOUT HARMONICS)
Analog Input Frequency 37 MHz
ADC (46.08 MHz BW)
CDMA (1.25 MHz BW)
WCDMA (5.0 MHz BW)
Analog Input Frequency 70 MHz
ADC (46.08 MHz BW)
CDMA (1.25 MHz BW)
WCDMA (5.0 MHz BW)
Analog Input Frequency 150 MHz
ADC (46.08 MHz BW)
CDMA (1.25 MHz BW)
WCDMA (5.0 MHz BW)
Analog Input Frequency 200 MHz
ADC (46.08 MHz BW)
CDMA (1.25 MHz BW)
WCDMA (5.0 MHz BW)
WORST HARMONIC2 (ANALOG INPUT @ −1 dBFS)
37 MHz
70 MHz
150 MHz
200 MHz
INTERMODULATION DISTORTION (TWO-TONES SEPARATED BY 1 MHz)3
Analog Input = 55/56 MHz
ANALOG INPUT BANDWIDTH
1
Analog input = −1 dB below full scale.
Includes Harmonic 2 through Harmonic 6.
3
Analog input = each −7 dB below full scale.
2
Rev. 0 | Page 7 of 88
Temp
Test Level
Min
Typ
25°C
Full
25°C
V
II
V
88
74.5
90.0
84
dB
dB
dB
25°C
Full
25°C
V
II
V
87.5
73.5
89
83
dB
dB
dB
25°C
25°C
25°C
V
V
V
73
88
82
dB
dB
dB
25°C
25°C
25°C
V
V
V
72
87
81
dB
dB
dB
Full
Full
Full
Full
II
V
V
V
93
91
71
63
dBc
dBc
dBc
dBc
25°C
25°C
V
V
90
270
dBc
MHz
85
Max
Unit
AD6654
ELECTRICAL CHARACTERISTICS
AVDD = 5.0 V, DRVDD = 3.3 V, VDDCORE = 1.8 V, VDDIO = 3.3 V, maximum rated sample rate, differential input, unless
otherwise noted.
Table 6.
Parameter (Conditions)
LOGIC INPUTS (NOT 5 V TOLERANT)
Logic Compatibility
Logic 1 Voltage
Logic 0 Voltage
Logic 1 Current
Logic 0 Current
Logic 1 Current (Inputs With Pull-Down)
Logic 0 Current (Inputs With Pull-Up)
Input Capacitance
LOGIC OUTPUTS
Logic Compatibility
Logic 1 Voltage (IOH = 0.25 mA)
Logic 0 Voltage (IOL = 0.25 mA)
SUPPLY CURRENTS
WCDMA (92.16 MSPS) EXAMPLE1
IAVDD
IDRVDD
IVDD
IVDDIO
CDMA2000 (92.16 MSPS) EXAMPLE1
IAVDD
IDRVDD
IVDD
IVDDIO
TDS-CDMA (76.8 MSPS) EXAMPLE1, 2
IAVDD
IDRVDD
IVDD
IVDDIO
TOTAL POWER DISSIPATION
WCDMA (92.16 MSPS)1
CDMA2000 (92.16 MSPS)1
TDS-CDMA (76.8 MSPS)1, 2
1
2
Temp
Test Level
Full
Full
Full
Full
Full
Full
Full
25°C
IV
IV
IV
IV
IV
IV
IV
V
Full
Full
Full
IV
IV
IV
25°C
25°C
25°C
25°C
V
V
V
V
275
32
460
60
mA
mA
mA
mA
25°C
25°C
25°C
25°C
V
V
V
V
275
32
435
25
mA
mA
mA
mA
25°C
25°C
25°C
25°C
V
V
V
V
275
32
250
15
mA
mA
mA
mA
25°C
25°C
25°C
V
V
V
2.5
2.3
2.0
W
W
W
ADC input port, all six DDC channels, and the relevant signal processing blocks are active.
PLL is turned off for power savings.
Rev. 0 | Page 8 of 88
Min
Typ
Max
Unit
3.6
+0.8
10
10
V
V
µA
µA
3.3 V CMOS
2.0
−0.3
1
1
4
2.4
3.3 V CMOS
VDDIO − 0.2
0.2
pF
0.4
V
V
AD6654
TIMING CHARACTERISTICS
Table 7.
Parameter1, 2, 3
CLK TIMING REQUIREMENTS
tCLK
CLK Period
tCLKL
CLK Width Low
tCLKH
CLK Width High
INPUT WIDEBAND DATA TIMING REQUIREMENTS
tDEXP
↑CLK to EXP[2:0] Delay
PARALLEL OUTPUT PORT TIMING REQUIREMENTS (MASTER)
tDPREQ
↑PCLK to ↑Px REQ Delay (x = A, B, C)
tDPP
↑PCLK to Px[15:0] Delay (x = A, B, C)
tDPIQ
↑PCLK to Px IQ Delay (x = A, B, C)
tDPCH
↑PCLK to Px CH[2:0] Delay (x = A, B, C)
tDPGAIN
↑PCLK to Px Gain Delay (x = A, B, C)
tSPA
Px ACK to ↑PCLK Setup Time (x = A, B, C)
tHPA
Px ACK to ↑PCLK Hold Time (x = A, B, C)
PARALLEL OUTPUT PORT TIMING REQUIREMENTS (SLAVE)
tPCLK
PCLK Period
tPCLKL
PCLK Low Period
tPCLKH
PCLK High Period
tDPREQ
↑PCLK to ↑Px REQ Delay (x = A, B, C)
tDPP
↑PCLK to Px[15:0] Delay (x = A, B, C)
tDPIQ
↑PCLK to Px IQ Delay (x = A, B, C)
tDPCH
↑PCLK to Px CH[2:0] Delay (x = A, B, C)
tDPGAIN
↑PCLK to Px Gain Delay (x = A, B, C)
tSPA
Px ACK to ↓PCLK Setup Time (x = A, B, C)
tHPA
Px ACK to ↓PCLK Hold Time (x = A, B, C)
MISC PINS TIMING REQUIREMENTS
tRESET
RESET Width Low
tDIRP
CPUCLK/SCLK to IRP Delay
tSSYNC
SYNC(0, 1, 2, 3) to ↑CLK Setup Time
tHSYNC
SYNC(0, 1, 2, 3) to ↑CLK Hold Time
Temp
Test Level
Min
Typ
Full
Full
Full
IV
IV
IV
5.154
5.154
10.85
0.5 × tCLK
0.5 × tCLK
Full
IV
5.98
10.74
ns
Full
Full
Full
Full
Full
Full
Full
IV
IV
IV
IV
IV
IV
IV
1.77
2.07
0.48
0.38
0.23
4.59
0.90
3.86
5.29
5.49
5.35
4.95
ns
ns
ns
ns
ns
ns
ns
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
IV
IV
IV
IV
IV
IV
IV
IV
IV
IV
5.0
1.7
0.7
4.72
4.8
4.83
4.88
5.08
6.09
1.0
Full
Full
Full
Full
IV
V
IV
IV
30
7.5
0.87
0.67
1
All timing specifications are valid over the VDDCORE range of 1.7 V to 1.9 V, and the VDDIO range of 3.0 V to 3.6 V.
CLOAD = 40 pF on all outputs, unless otherwise noted.
3
These timing parameters are derived from the ADC ENC rate with DDC CLK driven directly from ADC DR output.
2
Rev. 0 | Page 9 of 88
Max
Unit
ns
ns
ns
0.5 × tPCLK
0.5 × tPCLK
8.87
8.48
10.94
10.09
11.49
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
AD6654
MICROPORT TIMING CHARACTERISTICS
Table 8.
Parameter1, 2
MICROPORT CLOCK TIMING REQUIREMENTS
tCPUCLK
CPUCLK Period
tCPUCLKL
CPUCLK Low Time
tCPUCLKH
CPUCLK High Time
INM MODE WRITE TIMING (MODE = 0)
tSC
Control3 to ↑CPUCLK Setup Time
tHC
Control3 to ↑CPUCLK Hold Time
tSAM
Address/Data to ↑CPUCLK Setup Time
tHAM
Address/Data to ↑CPUCLK Hold Time
tDRDY
↑CPUCLK to RDY (DTACK) Delay
tACC
Write Access Time
INM MODE READ TIMING (MODE = 0)
tSC
Control3 to ↑CPUCLK Setup Time
tHC
Control3 to ↑CPUCLK Hold Time
tSAM
Address to ↑CPUCLK Setup Time
tHAM
Address to ↑CPUCLK Hold Time
tDD
↑CPUCLK to Data Delay
tDRDY
↑CPUCLK to RDY (DTACK) Delay
tACC
Read Access Time
MNM MODE WRITE TIMING (MODE = 1)
tSC
Control3 to ↑CPUCLK Setup Time
tHC
Control3 to ↑CPUCLK Hold Time
tSAM
Address/Data to ↑CPUCLK Setup Time
tHAM
Address/Data to ↑CPUCLK Hold Time
tDDTACK
↑CPUCLK to DTACK (RDY) Delay
tACC
Write Access Time
MNM MODE READ TIMING (MODE = 1)
tSC
Control3 to ↑CPUCLK Setup Time
tHC
Control3 to ↑CPUCLK Hold Time
tSAM
Address to ↑CPUCLK Setup Time
tHAM
Address to ↑CPUCLK Hold Time
tDD
CPUCLK to Data Delay
tDDTACK
↑CPUCLK to DTACK (RDY) Delay
tACC
Read Access Time
Temp
Test Level
Min
Typ
Full
Full
Full
IV
IV
IV
10.0
1.53
1.70
0.5 × tCPUCLK
0.5 × tCPUCLK
Full
Full
Full
Full
Full
IV
IV
IV
IV
IV
0.80
0.09
0.76
0.20
3.51
6.72
ns
ns
ns
ns
ns
Full
IV
3 × tCPUCLK
9 × tCPUCLK
ns
Full
Full
Full
Full
Full
Full
IV
IV
IV
IV
V
IV
4.50
6.72
ns
ns
ns
ns
ns
ns
Full
IV
3 × tCPUCLK
9 × tCPUCLK
ns
Full
Full
Full
Full
Full
IV
IV
IV
IV
IV
1.00
0.00
0.00
0.57
4.10
5.72
ns
ns
ns
ns
ns
Full
IV
3 × tCPUCLK
9 × tCPUCLK
ns
Full
Full
Full
Full
Full
Full
IV
IV
IV
IV
V
IV
1.00
0.00
0.00
0.57
4.20
6.03
ns
ns
ns
ns
ns
ns
Full
IV
3 × tCPUCLK
9 × tCPUCLK
ns
1
Rev. 0 | Page 10 of 88
Unit
ns
ns
ns
1.00
0.03
0.80
0.20
5.0
5.0
All timing specifications are valid over the VDDCORE range of 1.7 V to 1.9 V, and the VDDIO range of 3.0 V to 3.6 V.
CLOAD = 40 pF on all outputs, unless otherwise noted.
3
Specification pertains to control signals: R/W, (WR), DS, (RD), and CS.
2
Max
AD6654
SERIAL PORT TIMING CHARACTERISTICS
Table 9.
Parameter1, 2, 3
SERIAL PORT CLOCK TIMING REQUIREMENTS
tSCLK
SCLK Period
tSCLKL
SCLK Low Time
tSCLKH
SCLK High Time
SPI PORT CONTROL TIMING REQUIREMENTS (MODE = 0)
tSSDI
SDI to ↑SCLK Setup Time
tHSDI
SDI to ↑SCLK Hold Time
tSSCS
SCS to ↑SCLK Setup Time
tHSCS
SCS to ↑SCLK Hold Time
tDSDO
↑SCLK to SDO Delay Time
SPORT MODE CONTROL TIMING REQUIREMENTS (MODE = 1)
tSSDI
SDI to ↑SCLK Setup Time
tHSDI
SDI to ↑SCLK Hold Time
tSSRFS
SRFS to ↓SCLK Setup Time
tHSRFS
SRFS to ↓SCLK Hold Time
tSSTFS
STFS to ↓SCLK Setup Time
tHSTFS
STFS to ↓SCLK Hold Time
tSSCS
SCS to ↑SCLK Setup Time
tHSCS
SCS to ↑SCLK Hold Time
tDSDO
↑SCLK to SDO Delay Time
Temp
Test Level
Min
Typ
Full
Full
Full
IV
IV
IV
10.0
1.60
1.60
0.5 × tSCLK
0.5 × tSCLK
Full
Full
Full
IV
IV
IV
1.30
0.40
4.12
Max
Unit
ns
ns
ns
ns
ns
ns
Full
IV
−2.78
Full
IV
4.28
Full
Full
Full
Full
Full
Full
Full
IV
IV
IV
IV
IV
IV
IV
0.80
0.40
1.60
−0.13
1.60
−0.30
4.12
ns
ns
ns
ns
ns
ns
ns
Full
IV
−2.76
ns
Full
IV
4.29
1
All timing specifications are valid over the VDDCORE range of 1.7 V to 1.9 V and the VDDIO range of 3.0 V and 3.6 V.
CLOAD = 40 pF on all outputs, unless otherwise noted.
3
SCLK rise/fall time should be 3 ns maximum.
2
Rev. 0 | Page 11 of 88
ns
7.96
7.95
ns
ns
AD6654
TIMING DIAGRAMS
05156-002
RESET
tRESL
Figure 2. Reset Timing Requirements
tCLKH
05156-003
CLK
tCLKL
Figure 3. CLK Switching Characteristics
tCPUCLKH
05156-004
CPUCLK
tCPUCLKL
Figure 4. CPUCLK Switching Characteristics
tSCLKH
05156-005
SCLK
tSCLKL
Figure 5. SCLK Switching Characteristics
CLK
tHSYNC
05156-006
tSSYNC
SYNC [3:0]
Figure 6. SYNC Timing Inputs
tCLK
tCLKL
CLK
tCLKH
05156-007
tDEXP
EXPx [2:0]
Figure 7. Gain Control Word Output Switching Characteristics
Rev. 0 | Page 12 of 88
AD6654
PCLK
tSPA
tHPA
PxACK
tDPREQ
PxREQ
Px [15:0]
tDPP
I [15:0]
PxIQ
tDPP
Q [15:0]
RSSI [11:0]
tDPP
tDPP
I [15:0]
tDPIQ
tDPIQ
tDPCH
tDPCH
PxCH [2:0]
Q [15:0]
tDPP
RSSI [11:0]
PxCH [2:0] = CHANNEL NO.
PxCH [2:0] = CHANNEL NO.
tDPGAIN
tDPGAIN
05156-008
tDPP
PxGAIN
Figure 8. Master Mode PxACK to PCLK Switching Characteristics
PCLK
PxACK
tDPREQ
TIED LOGIC HIGH ALL THE TIME
PxREQ
tDPP
PxIQ
I [15:0]
tDPP
Q [15:0]
RSSI [11:0]
tDPIQ
tDPP
I [15:0]
Q [15:0]
tDPP
RSSI [11:0]
tDPIQ
tDPCH
PxCH [2:0]
tDPP
tDPCH
PxCH [2:0] = CHANNEL NO.
PxCH [2:0] = CHANNEL NO.
tDPGAIN
PxGAIN
Figure 9. Master Mode PxREQ to PCLK Switching Characteristics
Rev. 0 | Page 13 of 88
tDPGAIN
05156-009
Px [15:0]
tDPP
AD6654
CPUCLK
RD
tSC
tHC
tSC
tHC
WR
CS
tSAM
tHAM
A [7:0]
VALID ADDRESS
tSAM
tHAM
D [15:0]
VALID DATA
tDRDY
RDY
NOTE:
tACC ACCESS TIME DEPENDS ON THE ADDRESS ACCESSED. IT CAN VARY FROM 3 TO 9 CPUCLK CYCLES.
05156-010
tACC
Figure 10. INM Microport Write Timing Requirements
CPUCLK
RD
tHC
tSC
WR
CS
tHC
tSC
tSAM
A [7:0]
tHAM
VALID ADDRESS
tDD
D [15:0]
VALID DATA
tDRDY
RDY
Figure 11. INM Microport Read Timing Requirements
Rev. 0 | Page 14 of 88
05156-011
tACC
NOTE:
tACC ACCESS TIME DEPENDS ON THE ADDRESS ACCESSED. IT CAN VARY FROM 3 TO 9 CPUCLK CYCLES.
AD6654
CPUCLK
tSC
tHC
tSC
tHC
tSC
tHC
DS
R/W
CS
tHAM
tSAM
A [7:0]
VALID ADDRESS
tSAM
D [15:0]
tHAM
VALID DATA
tDDTACK
DTACK
NOTE:
tACC ACCESS TIME DEPENDS ON THE ADDRESS ACCESSED. IT CAN VARY FROM 3 TO 9 CPUCLK CYCLES.
05156-012
tACC
Figure 12. MNM Microport Write Timing Requirements
CPUCLK
tSC
tHC
tSC
tHC
DS
R/W
tSC
tHC
tSAM
tHAM
CS
A [7:0]
VALID ADDRESS
tDD
VALID
DATA
D [15:0]
tDDTACK
tACC
NOTE:
tACC ACCESS TIME DEPENDS ON THE ADDRESS ACCESSED. IT CAN VARY FROM 3 TO 9 CPUCLK CYCLES.
Figure 13. MNM Microport Read Timing Requirements
Rev. 0 | Page 15 of 88
05156-013
DTACK
AD6654
SCLK
tSSCS
tHSCS
SCS
SMODE
LOGIC 1
tHSDI
tSSDI
SDI
D0
D1
D2
D3
D4
D5
D6
D7
tHSRFS
tSSRFS
05156-014
SRFS
MODE
LOGIC 1
Figure 14. SPORT Mode Write Timing Characteristics
SCLK
tSSCS
tHSCS
SCS
SMODE
LOGIC 1
tDSDO
SDO
D0
D1
D2
D3
D4
D5
D6
D7
tHSTFS
tSSTFS
05156-015
STFS
MODE
LOGIC 1
Figure 15. SPORT Mode Read Timing Characteristics
SCLK
tSSCS
tHSCS
SCS
SMODE
LOGIC 1
D0
D1
D2
D3
D4
D5
MODE
LOGIC 0
Figure 16. SPI Mode Write Timing Characteristics
Rev. 0 | Page 16 of 88
D6
D7
05156-016
tSSDI
SDI
tHSDI
AD6654
SCLK
SCS
tSSCS
tHSCS
SMODE
LOGIC 0
tDSDO
D0
D1
D2
D3
D4
D5
LOGIC 0
MODE
Figure 17. SPI Mode Read Timing Characteristics
Rev. 0 | Page 17 of 88
D6
D7
05156-017
SDO
AD6654
ABSOLUTE MAXIMUM RATINGS
Table 10.
Parameter
AVDD
DRVDD
VDDCORE
VDDIO
Analog/Encode Input Voltage
Analog Input Current
Digital Input Voltage
Digital Output Voltage
Operating Temperature Range
(Ambient)
Junction Temperature Under Bias
Storage Temperature Range
Rating
0 to +7.0 V
0 to +4.0 V
−0.3 V to +2.2 V
0 to +4.0 V
0 to AVDD
25 mA
−0.3 V to + 3.6 V (not 5 V
tolerant)
−0.3 V to VDDIO + 0.3 V
−25°C to +85°C
150°C
−65°C to +150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL CHARACTERISTICS
256 BGA, 17 mm sq.
θJA = 21°C/W, no airflow.
Estimate based on JEDEC JC51-2 model using horizontally
positioned 4-layer board.
EXPLANATION OF TEST LEVELS
Test Level
I
II
III
Description
100% production tested.
100% production tested at 25°C.
Sample tested only.
IV
V
Parameter guaranteed by design and analysis.
Parameter is typical value only.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. 0 | Page 18 of 88
AD6654
1
A
DGND
2
D14
3
4
5
6
7
8
9
10
11
12
13
14
15
16
D12
CPUCLK
(SCLK)
PC3
PCCH1
PA12
PAIQ
PAGAIN
PB6
CLK
OVR
AVDD
AVDD
AGND
AGND
A
PC5
PA5
PA15
PAACK
PB2
PB4
EXPC2
DNC
AVDD
AVDD
AGND
AGND
B
PA3
PA9
PACH2
PB3
PB9
EXPC1
AVDD
AVDD
AVDD
AGND
AGND
C
B
D7
CHIPID3
CHIPID2
DS
(RD,
SRFS)
C
CHIPID0
MODE
DTACK
(RDY,
SDO)
R/W
(WR,
STFS)
PC0
D
EXT_
FILTER
MSB_
FIRST
CS
(SCS)
PC6
PC2
PA1
PA7
PACH0
PB0
PB15
EXPC0
DRVDD
AVDD
AVDD
AGND
AGND
D
PCACK
VDD
CORE
VDD
CORE
VDD
CORE
VDDIO
VDDIO
VDDIO
DRVDD
AVDD
AVDD
AGND
AGND
E
E
CHIPID1
IRP
VDDIO
VDD
CORE
F
SMODE
D13
D15
RESET
D1
VDD
CORE
VDD
CORE
VDD
CORE
VDDIO
VDDIO
VDDIO
DRVDD
AVDD
AVDD
AGND
C2
F
G
DGND
D8
D9
D2
D5
DGND
DGND
DGND
DGND
DGND
DGND
DRVDD
AVDD
AVDD
AGND
AGND
G
H
D3
D11
D4
D10
A6
DGND
DGND
DGND
DGND
DGND
DGND
DRVDD
AVDD
AVDD
AGND
C1
H
J
DGND
D6
D0
A7
A1
DGND
DGND
DGND
DGND
DGND
DGND
DRVDD
AVDD
AVDD
AGND
AGND
J
K
A5
A4
A0 (SDI)
A2
PC8
DGND
DGND
DGND
DGND
DGND
DGND
DRVDD
AVDD
AVDD
AGND
AGND
K
L
A3
PC12
PC11
PC15
PC10
VDDIO
VDDIO
VDDIO
VDD
CORE
VDD
CORE
VDD
CORE
DRVDD
AVDD
AVDD
AGND
AIN –
L
M
PC14
PC13
PC9
PC7
PCCH0
VDDIO
VDDIO
VDDIO
VDD
CORE
VDD
CORE
VDD
CORE
DRVDD
AVDD
AVDD
AGND
AIN+
M
N
PC1
PC4
PA13
PA8
PA0
PAREQ
PB1
PBREQ
DGND
DGND
DGND
DRVDD
AVDD
AVDD
AGND
AGND
N
P
PCIQ
PCREQ
PA14
PA10
PB10
PB7
PB8
PBCH1
PBACK
PBCH0
SYNC2
DRVDD
AVDD
AVDD
AGND
AGND
P
R
PCCH2
PCGAIN
PA6
PA2
PACH1
PB13
PB11
PBCH2
PB14
PBGAIN
SYNC1
DRVDD
AGND
AGND
AGND
ENC–
R
T
DGND
PA11
PA4
PCLK
PB5
PB12
PBIQ
DGND
DNC
SYNC0
SYNC3
DR
AGND
VREF
AGND
ENC+
T
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
DNC = DO NOT CONNECT
05156-018
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 18. 256 BGA Configuration (Top View)
Table 11. Pin Function Descriptions
Name
POWER SUPPLY
AVDD
DRVDD
VDDCORE
VDDIO
DGND
AGND
ADC INPUTS
AIN+
AIN−
ENC+
ENC−
ADC OUTPUTS
DR
OVR
VREF
C1
C2
Type
Pin Number
Function
Power
Power
Power
Power
Ground
Ground
See Table 12
See Table 12
See Table 12
See Table 12
See Table 12
See Table 12
5 V Analog ADC Core Supply.
3.3 V ADC Output Driver Supply.
1.8 V Digital DDC Core Supply.
3.3 V Digital DDC I/O Supply.
Digital Core and I/O Ground.
Analog ADC Ground.
Input
Input
Input
Input
M16
L16
T16
R16
Differential Analog Input.
Differential Analog Input.
Differential Encode Input. Conversion initiated on rising edge.
Differential Encode Input.
Output
T12
Output
Output
Output
Output
A12
T14
H16
F16
Data Ready. Inverted and delayed representation of ENC+ used for driving the DDC CLK
input.
Overange Bit. A logic high indicates analog input exceeds ±FS.
2.4 V Fixed Internal Voltage Reference. Bypass to AGND with 0.1 µF chip capacitor.
Compensation Pin for ADC Voltage Reference. Bypass to AGND with 0.1 µF chip capacitor.
Compensation Pin for ADC Voltage Reference. Bypass to AGND with 0.1 µF chip capacitor.
Rev. 0 | Page 19 of 88
AD6654
Name
Type
DDC INPUTS
CLK
Input
SYNC0
Input
SYNC1
Input
SYNC2
Input
SYNC3
Input
DDC OUTPUTS
EXPC [2:0]
Output
DDC OUTPUT PORTS
PCLK
Bi-dir
PADATA[15:0]
Output
PACH[2:0]
Output
PAIQ
Output
PAGAIN
Output
PAACK
Input
PAREQ
Output
PBDATA[15:0]
Output
PBCH[2:0]
Output
PBIQ
Output
PBGAIN
Output
PBACK
Input
PBREQ
Output
PCDATA[15:0]
Output
PCCH[2:0]
Output
PCIQ
Output
PCGAIN
Output
PCACK
Input
PCREQ
Output
MICROPORT CONTROL
D[15:0]
Bi-Dir
A[7:0]
Input
DS (RD)
Input
DTACK (RDY)1
Output
Input
R/W (WR)
MODE
Input
CS
Input
CPUCLK
Input
CHIPID[3:0]
Input
SERIAL PORT CONTROL
SCLK
Input
SDO1
Output
SDI2
Input
STFS
Input
SRFS
Input
SCS
Input
MSB_FIRST
Input
SMODE
MISC PINS
DNC
IRP1
RESET
EXT_FILTER
1
2
Pin Number
Function
A11
T10
R11
P11
T11
DDC Clock Input.
Synchronization Input 0. SYNC pins are independent of channels.
Synchronization Input 1.
Synchronization Input 2.
Synchronization Input 3.
D11, C11, B11
External VGA Gain Control Bits. GND all pins if not used.
T4
See Table 12
D8, R5, C8
A8
A9
B8
N6
See Table 12
P10, P8, R8
T7
R10
P9
N8
See Table 12
M5, A6, R1
P1
R2
E5
P2
Parallel Output Port Clock. PCLK is bi-directional: master mode = output, slave mode = input.
Parallel Output Port A Data Bus.
Channel Indicator Output Port A.
Parallel Port A I/Q Data Indicator. Logic 1 indicates I data on data bus.
Parallel Port A Gain Word Output Indicator. Logic 1 indicates gain word on data bus.
Parallel Port A Acknowledge (Active High).
Parallel Port A Request (Active High).
Parallel Output Port B Data Bus.
Channel Indicator Output Port B.
Parallel Port B I/Q Data Indicator. Logic 1 indicates I data on data bus.
Parallel Port B Gain Word Output Indicator. Logic 1 indicates gain word on data bus.
Parallel Port B Acknowledge (Active High).
Parallel Port B Request (Active High)
Parallel Output Port C Data Bus.
Channel Indicator Output Port C.
Parallel Port C I/Q Data Indicator. Logic 1 indicates I data on data bus.
Parallel Port C Gain word Output Indicator. Logic 1 indicates gain word on data bus.
Parallel Port C Acknowledge (Active High).
Parallel Port C Request (Active High).
See Table 12
See Table 12
B4
C3
Bidirectional Microport Data. This bus is three-stated when CS is high.
Microport Address Bus.
Active Low Data Strobe, MODE = 1. Active low read strobe when MODE = 0.
Active Low Data Acknowledge, MODE = 1. Microport status pin when MODE = 0. Terminate
to VDDIO through external 1 kΩ pull-up resistor.
Read/Write Strobe, MODE = 1. Active low write strobe when MODE = 0.
Mode Select. Logic 0 = Intel® mode, Logic 1 = Motorola mode.
Active Low Chip Select. Logic 1 three-states the microport data bus.
Microport CLK Input. (Input only.)
Chip ID Input Pins.
C4
C2
D3
A4
C1, E1, B3, B2
A4
C3
K3
C4
B4
D3
D2
Input
F1
------Output
Input
Input
B12, T9
E2
F4
D1
Serial Clock. Should have a rise/fall time of 3ns max.
Serial Port Data Output. Terminate to VDDIO through external 1 kΩ pull-up resistor.
Serial Port Data Input.
Serial Transmit Frame Sync.
Serial Receive Frame Sync.
Serial Chip Select.
Most Significant Bit_First. Selects MSB_FIRST into SDI pin, and MSB_FIRST out of SDO pin.
Logic 1 = MSB_FIRST; Logic 0 = LSB_FIRST
Serial Mode Select.
Do Not Connect.
Interrupt Pin (Active Low). Terminate to VDDIO through external 1 kΩ pull-up resistor.
Master Reset, Active Low.
PLL Loop Filter (Analog Pin). Connect to VDDCORE through series 250 Ω and 0.01 µF
capacitor.
Pins with internal pull-up resistor of nominal 70 kΩ.
Pins with internal pull-down resistor of nominal 70 kΩ.
Rev. 0 | Page 20 of 88
AD6654
Table 12. Pin Listing for Power, Ground, and Data Buses
Name
AVDD
AGND
DRVDD
VDDIO
VDDCORE
DGND
PADATA[15:0]
PBDATA[15:0]
PCDATA[15:0]
D[15:0]
A[7:0]
Pin Number
A13, A14, B13, B14, C12, C13, C14, D13, D14, E13, E14, F13, F14, G13, G14, H13, H14, J13, J14, K13, K14, L13, L14, M13,
M14, N13, N14, P13, P14
A15, A16, B15, B16, C15, C16, D15, D16, E15, E16, F15, G15, G16, H15, J15, J16, K15, K16, L15, M15, N15, N16, P15, P16,
R13, R14, R15, T13, T15
D12, E12, F12, G12, H12, J12, K12, L12, M12, N12, P12, R12
E3, E9, E10, E11, F9, F10, F11, L6, L7, L8, M6, M7, M8
E4, E6, E7, E8, F6, F7, F8, L9, L10, L11, M9, M10, M11
A1, G1, G6, G7, G8, G9, G10, G11, H6, H7, H8, H9, H10, H11, J1, J6, J7, J8, J9, J10, J11, K6, K7, K8, K9, K10, K11, N9, N10,
N11, T1, T8
N5, D6, R4, C6,T3, B6, R3, D7, N4, C7, P4, T2, A7, N3, P3, B7
D9, N7, B9, C9, B10, T5, A10, P6, P7, C10, P5, R7, T6, R6, R9, D10
C5, N1, D5, A5, N2, B5, D4, M4, K5, M3, L5, L3, L2, M2, M1, L4
J3, F5, G4, H1, H3, G5, J2, B1, G2, G3, H4, H2, A3, F2, A2, F3
K3, J5, K4, L1, K2, K1, H5, J4
Rev. 0 | Page 21 of 88
AD6654
TYPICAL PERFORMANCE CHARACTERISTICS
76
105
100
+85°C
72
ENCODE = 92.16MSPS
AIN = –1dBFS
30
50
70
90
110
130
150
170
HARMONICS
(SECOND, THIRD)
80
75
70
ENCODE = 92.16MSPS
AIN = –1dBFS
TEMPERATURE = 25°C
60
190
0
20
40
AIN FREQUENCY (MHz)
110
110
100
100
ENCODE = 92.16MSPS
AIN = 37.7MHz
TEMPERATURE = 25°C
70
dBc
60
50
40
SFDR = 90dB
REFERENCE LINE
30
20
10
0
–90
–80
–70
–60
–50
–40
–30
–20
–10
ENCODE = 92.16MSPS
AIN = 70MHz
TEMPERATURE = 25°C
80
160
180
200
dBc
70
60
50
SFDR = 90dB
REFERENCE LINE
40
30
20
10
0
–90
0
–80
–70
–60
–50
–40
–30
–20
–10
0
ANALOG INPUT POWER LEVEL (dBFS)
Figure 23. Single Tone SFDR at 70 MHz
0
0
32k FFT
AIN = –1dBFS
SNR = 89dB (1.25MHz BW)
32k FFT
–15
–30
–45
–45
–60
–60
–75
–90
–105
–105
–120
–120
05156-064
–90
–135
750k
500k
250k
0
–250k
–500k
–750k
–150
1.25M
1.00M
750k
500k
250k
0
–250k
–500k
–750k
–1.00M
–150
–1.25M
–135
–1.00M
–75
05156-066
(dBFS)
–30
–1.25M
140
90
Figure 20. Single Tone SFDR at 37.7 MHz
(dBFS)
120
dBFS
ANALOG INPUT POWER LEVEL (dBFS)
–15
100
05156-072
dBFS
WORST CASE SPURIOUS (dBFS and dBc)
120
80
80
Figure 22. Harmonics vs. Analog Frequency (IF)
05156-071
WORST CASE SPURIOUS (dBFS and dBc)
Figure 19. ADC Noise vs. Analog Frequency (46.08 MHz BW)
90
60
ANALOG INPUT FREQUENCY (MHz)
1.25M
70
10
85
65
05156-073
71
90
1.00M
73
WORST OTHER SPUR
95
05156-074
+25°C –25°C
74
SNR (dB)
WORST CASE HARMONIC (dBc)
75
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 24. CDMA Carrier AIN = 70 MHz; ENC = 92.16 MSPS
Figure 21. CDMA Single Tone AIN = 70 MHz; ENC = 92.16 MSPS
Rev. 0 | Page 22 of 88
AD6654
0
0
32k FFT
AIN = –1dBFS
SNR = 88dB (1.25MHz BW)
32k FFT
–15
–30
–45
–45
–60
–60
–75
–75
–90
–90
–105
–105
–120
–120
–135
FREQUENCY (Hz)
1.25M
1.00M
750k
500k
32k FFT
–15
–30
–45
–45
–60
–60
–75
–75
–90
–90
–105
–105
–120
–120
–135
FREQUENCY (Hz)
3.5M
2.8M
2.1M
1.4M
700k
0
–700k
–1.4M
–2.1M
–3.5M
–2.8M
–150
3.5M
2.8M
2.1M
1.4M
700k
0
–700k
–1.4M
–2.1M
–2.8M
–3.5M
–150
05156-069
(dBFS)
–30
05156-067
FREQUENCY (Hz)
Figure 26. WCDMA Single Tone AIN = 70 MHz; Encode = 92.16 MSPS
Figure 29. WCDMA Carrier AIN = 70 MHz; Encode = 92.16 MSPS
0
0
32k FFT
AIN = –1dBFS
SNR = 82dB (5MHz BW)
32k FFT
–15
–30
–45
–45
–60
–60
–75
–75
–90
–105
–105
–120
–120
05156-068
–90
–135
3.5M
2.8M
2.1M
1.4M
700k
0
–1.4M
–3.5M
FREQUENCY (Hz)
–2.1M
–150
3.5M
2.8M
2.1M
1.4M
700k
0
–700k
–1.4M
–2.1M
–2.8M
–3.5M
–150
–2.8M
–135
05156-084
(dBFS)
–30
–700k
(dBFS)
0
AIN = –1dBFS
SNR = 83dB (5MHz BW)
32k FFT
–135
(dBFS)
250k
Figure 28. CDMA Carrier AIN = 151.5 MHz; ENC = 92.16 MSPS
0
–15
0
FREQUENCY (Hz)
Figure 25. CDMA Single Tone AIN = 151.5 MHz; ENC = 92.16 MSPS
–15
–250k
–750k
–1.25M
–500k
–150
1.25M
1.00M
750k
500k
250k
0
–250k
–500k
–750k
–1.00M
–1.25M
–150
–1.00M
–135
05156-083
(dBFS)
–30
05156-065
(dBFS)
–15
FREQUENCY (Hz)
Figure 27. WCDMA Single Tone AIN = 151.5 MHz; Encode = 92.16 MSPS
Rev. 0 | Page 23 of 88
Figure 30. WCDMA Carrier AIN = 151.5 MHz; Encode = 92.16 MSPS
AD6654
0
110
F1
F2
–30
–45
(dBFS)
–60
–75
–90
–105
05156-063
–120
1.00M
750k
500k
250k
0
–250k
–500k
–750k
–1.00M
–1.25M
–150
90
dBFS
80
70
60
50
dBc
SFDR = 90dB
REFERENCE LINE
40
30
20
10
0
–77
1.25M
–135
100
05156-070
AIN = –7dBFS
32k FFT
WORST CASE SPURIOUS (dBFS and dBc)
–15
–67
–57
–47
–37
–27
–17
INPUT POWER LEVEL (F1 = F2 (dBFS))
FREQUENCY (Hz)
Figure 31. CDMA Two Tones at 55 MHz and 56 MHz; ENC = 92.16 MSPS
Rev. 0 | Page 24 of 88
Figure 32. Two Tone SFDR at 55 MHz and 56 MHz
–7
AD6654
ADC EQUIVALENT CIRCUITS
AVDD
AVDD
AVDD
2.4V
VREF
VREF
AVDD
AVDD
05156-023
100µA
CURRENT
MIRROR
Figure 33. ADC 2.4 V Reference
05156-025
C1, C2
LOADS
Figure 35. ADC Compensation Pins, C1 and C2
AVDD
AVDD
AVDD
AVDD
10kΩ
VCH AVDD
10kΩ
ENC+
ENC–
10kΩ
AIN+
BUF
10kΩ
T/H
500Ω
VCL
BUF
VCH AVDD
VREF
BUF
AIN–
Figure 34. ADC Encode Inputs
VCL
Figure 36. ADC Analog Input Stage
Rev. 0 | Page 25 of 88
T/H
05156-026
05156-024
500Ω
LOADS
AD6654
TERMINOLOGY
Analog Bandwidth
The analog input frequency at which the spectral power of the
fundamental frequency (as determined by the FFT analysis) is
reduced by 3 dB.
Differential Analog Input Resistance,
Capacitance, and Impedance
The real and complex impedances measured at each analog
input port. The resistance is measured statically, and the
capacitance and differential input impedances are measured
with a network analyzer.
Differential Analog Input Voltage Range
The peak-to-peak differential voltage that must be applied to
the converter to generate a full-scale response. Peak differential
voltage is computed by observing the voltage on a single pin
and subtracting the voltage from the other pin, which is 180°
out of phase. Peak-to-peak differential is computed by rotating
the inputs phase 180° and taking the peak measurement again.
Then the difference is computed between both peak
measurements.
Encode Pulse Width/Duty Cycle
Pulse width high is the minimum amount of time that the
ENCODE pulse should be left in Logic 1 state to achieve the
rated performance. Pulse width low is the minimum time
ENCODE pulse should be left in the low state. Several internal
timing parameters are a function of tENCL and tENCH, optimum
performance will be achieved with 50/50 duty cycle.
Harmonic Distortion, Second
The ratio of the rms signal amplitude to the rms value of the
second harmonic component, reported in dBc.
Full-Scale Input Power
Expressed in dBm. Computed using the following equation:
PowerFULL SCALE
⎞
⎟
⎟
⎟
⎟
⎟
⎟
⎠
Z
where Z is the input impedance, FS is the full scale of the device
for the frequency in question, SNR is the value for the particular
input level, and SIGNAL is the signal level within the ADC
reported in dB below full scale. This value includes both
thermal and quantization noise.
Power-Supply Rejection Ratio
The ratio of a change in input offset voltage to a change in
power-supply voltage.
Power-Supply Rise Time
The time from when the dc supply is initiated until the supply
output reaches the minimum specified operating voltage for the
AD6654, measured at the supply pin(s) of the AD6654.
Processing Gain
When the tuned channel occupies less bandwidth than the
input signal, this rejection of out-of-band noise is referred to as
processing gain. By using large decimation factors, processing
gain can improve the SNR of the ADC by 15 dB or more. Use
the following equation to estimate processing gain:
⎡ Sample _ Rate / 2 ⎤
Processing _ Gain = 10 log ⎢
⎥
⎣ Filter _ Bandwidth ⎦
Signal-to-Noise Ratio (Without Harmonics)
The ratio of the rms signal amplitude (set at 1 dB below full
scale) to the rms value of the sum of all other spectral
components, excluding the first five harmonics and dc.
Two-Tone Intermodulation Distortion Rejection
The ratio of the rms value of either input tone to the rms value
of the worst third-order intermodulation product, in dBc.
Minimum Conversion Rate
The encode rate at which the SNR of the lowest analog signal
frequency drops by no more than 3 dB below the guaranteed
limit.
Maximum Conversion Rate
Encode rate at which parametric testing is performed.
VNOISE =
⎛ FSdBm − SNRdBc − SIGNALdBFS ⎞
⎜
⎟
10
⎠
× 10 ⎝
Spurious-Free Dynamic Range (SFDR)
The ratio of the rms signal amplitude to the rms value of the
peak spurious spectral component. The peak spurious component might, or might not be, a harmonic. SFDR can be reported
in dBc (degrades as signal level is lowered), or dBFS (always
related back to converter full scale).
Harmonic Distortion, Third
The ratio of the rms signal amplitude to the rms value of the
third harmonic component, reported in dBc.
⎛ V 2 FULL SCALE
RMS
⎜
⎜
Z INPUT
= 10 log ⎜
0.001
⎜
⎜
⎜
⎝
Noise for Any Range Within the ADC
Two-Tone SFDR
Ratio of the rms value of either input tone to the rms value of
the peak spurious component. The peak spurious component
might, or might not be, an IMD product. SFDR can be reported
in dBc (degrades as signal level is lowered), or in dBFS (always
related back to converter full scale).
Worst Other Spur
Ratio of the rms signal amplitude to the rms value of the worst
spurious component (excluding the second and third harmonic)
reported in dBc.
Rev. 0 | Page 26 of 88
AD6654
THEORY OF OPERATION
ADC ARCHITECTURE
The AD6654 analog-to-digital converter (ADC) front end
employs a 3-stage subrange architecture. This design approach
achieves the required accuracy and speed, while maintaining
low power consumption.
The output of DAC1 is subtracted from the delayed analog
signal at the input of TH3 to generate a first residue signal. TH2
provides an analog pipeline delay to compensate for the digital
delay of ADC1.
The AD6654 front end has complementary analog input pins,
AIN+ and AIN−, as shown in Figure 1. Each analog input is
centered at 2.4 V and should swing ±0.55 V around this
reference (see Figure 36). Because AIN+ and AIN− are 180°
out of phase, the differential full-scale analog input signal is
2.2 V p-p.
The first residue signal is applied to a second conversion stage
consisting of a 5-bit ADC2, 5-bit DAC2, and pipeline TH4. The
second DAC requires 10 bits of precision, which is met by the
process with no trim. The input to TH5 is a second residue
signal generated by subtracting the quantized output of DAC2
from the first residue signal held by TH4. TH5 drives a final
6-bit ADC3.
Both analog inputs are buffered prior to the first track-andhold, TH1. The high state of the ENCODE pulse places TH1 in
hold mode. The held value of TH1 is applied to the input of a
5-bit coarse ADC1. The digital output of ADC1 drives a 5-bit
digital-to-analog converter, DAC1. DAC1 requires 14 bits of
precision that is achieved through laser trimming.
The digital outputs from ADC1, ADC2, and ADC3 are added
together and corrected in the digital error correction logic to
generate the final output data. The latency of the ADC core is
four CLK cycles. The resulting 14-bit ADC data is internally
routed directly to the integrated DDC for processing by the
4/6 independent DDC channels.
Rev. 0 | Page 27 of 88
AD6654
APPLICATION INFORMATION
Encoding the AD6654 ADC
The AD6654 encode signal must be a high quality, extremely
low phase noise source to prevent degradation of performance.
Maintaining 14-bit accuracy places a premium on encode clock
phase noise. SNR performance can easily degrade by 3 dB to
4 dB with 70 MHz analog input signals when using a high jitter
clock source. See the AN-501, Aperture Uncertainty and ADC
System Performance Application Note, for details.
For optimum performance, the AD6654 ADC front end must
be clocked differentially. The encode signals are usually accoupled into the ENC+ and ENC− pins via a transformer or
capacitors. The ENCODE pins are biased internally and require
no additional bias.
Figure 37 shows one preferred method for clocking the
AD6654. The clock source (low jitter) is converted from singleended to differential using an RF transformer. The back-to-back
Schottky diodes across the secondary of the transformer limit
clock excursions into the AD6654 to approximately 0.8 V p-p
differential. This helps prevent the large voltage swings of the
clock from feeding through to other portions of the AD6654,
and limits the noise presented to the encode inputs.
T1-4T
ENC+
0.1µF
AD6654
05156-027
CLOCK
SOURCE
ENC–
HSMS2812
DIODES
Figure 37. Crystal Clock Oscillator-Differential Encode
If a low jitter clock is available, another option is to ac-couple a
differential ECL/PECL signal to the encode input pins as shown
in Figure 38. A device that offers excellent jitter performance is
the MC100EL16 (or same family) from ON Semiconductor®.
There are also benefits at the PCB level. First, differential inputs
have high common-mode rejection to stray signals such as
ground and power noise. Second, they provide good rejection to
common-mode signals such as local oscillator feed-through.
The AD6654 analog input pins, AIN+ and AIN−, are centered
at 2.4 V, and the signal at each input should swing ±0.55 V
around this voltage. Because AIN+ and AIN− are 180° out of
phase, the full-scale differential analog input signal is 2.2 V p-p.
Each analog input connects through a 500 Ω resistor to the
2.4 V bias voltage and to the input of a differential buffer, as
shown in Figure 36. The resistor network on the input properly
biases the followers for maximum linearity and range.
Therefore, the analog source driving the AD6654 should be
ac-coupled to the input pins. Because the differential input
impedance of the AD6654 is 1 kΩ, the analog input power
requirement is only −2 dBm, simplifying the driver amplifier in
many cases. To take full advantage of this high input
impedance, a 20:1 transformer is required. This is a large ratio
that could result in unsatisfactory performance. In this case, a
lower step-up ratio could be used. The recommended method
for driving the analog input of the AD6654 is to use a 4:1
impedance ratio RF transformer.
For example, if RT is set to 60.4 Ω and RS is set to 25 Ω, along
with a 4:1 impedance ratio transformer, the input matches to a
50 Ω source with a full-scale drive of 4.8 dBm. Series resistors
(RS) on the secondary side of the transformer should be used to
isolate the transformer from A/D. This limits the amount of
dynamic current from the A/D flowing back into the secondary
of the transformer. The 50 Ω impedance matching can also be
incorporated on the secondary side of the transformer, as
shown in the evaluation board schematic.
ADT4-1WT
ANALOG INPUT
SIGNAL
RS
RT
VT
AD6654
RS
0.1µF
AIN–
0.1µF
ENC+
ECL/
PECL
AIN+
AD6654
05156-029
ADC CONFIGURATION NOTES
Figure 39. Transformer-Coupled Analog Input Circuit
ENC–
In applications where dc-coupling, or additional gain is
required, use a differential output op amp from Analog Devices,
Inc., such as AD8351, to drive the AD6654 (Figure 40). The
AD8351 op amp can be driven differentially, or configured to
provide single-ended-to-differential conversion.
05156-028
0.1µF
VT
Figure 38. Differential ECL for Encode
Driving the Analog Inputs
As with most high speed, high dynamic range ADCs, the analog
input to the AD6654 front end is differential. Differential inputs
improve on-chip performance, because signals are processed
through attenuation and gain stages. Most of the improvement
is a result of differential analog stages having high rejection of
even-order harmonics.
Rev. 0 | Page 28 of 88
AD6654
INHI
OPHI
25Ω
BALANCE
50Ω
SOURCE
RG
100nF
25Ω
AD6654
AD8351
OPLO 25Ω
INLO
AIN–
DIGITAL
OUT
VREF
VOCM
25Ω
N is a predivide factor and can be 1, 2, 4, or 8.
M is a 5-bit number between 4 and 20 (inclusive).
AIN+
05156-030
100nF
100nF
Figure 40. ADC Driving Application Using Differential Input
RF
SINGLEENDED
50Ω
SOURCE
OPHI
100nF
RG
100nF
25Ω
AD6654
AD8351
OPLO 25Ω
INLO
VOCM
25Ω
Table 13. PLL Clock Generation Predivider Control
AIN+
AIN–
VREF
DIGITAL
OUT
05156-062
INHI
R1
25Ω
The multiplication factor, M, is programmed using a 5-bit PLL
clock multiplier word in the ADC clock control register. A value
outside the valid range of 4 to 20 bypasses the PLL clock
multiplier and, therefore, the PLL clock is the same as the input
clock. The predivide factor, N, is programmed using a 2-bit
ADC pre-PLL clock divider word in the ADC clock control
register, as listed in Table 13.
100nF
Figure 41. ADC Driving Application Using Single-Ended Input
DDC CONFIGURATION NOTES
PLL Clock Multiplier
In the AD6654, the input clock rate must be the same as the
input data rate. In a typical digital down-converter architecture,
the clock rate is a limitation on the number of filter taps that
can be calculated in the programmable RAM coefficient filters
(MRCF, DRCF, and CRCF). For slower ADC clock rates (or for
any clock rate), this limitation can be overcome by using a PLL
clock multiplier to provide a higher clock rate to the RCF filters.
Using this clock multiplier, the internal signal processing clock
rate can be increased up to 200 MHz. The CLK signal is used as
an input to the PLL clock multiplier.
Predivide Word [1:0]
00
01
10
11
Divide-By Value for the Clock
Divide-by-1, bypass
Divide-by-2
Divide-by-4
Divide-by-8
For best signal processing advantage, the user should program
the clock multiplier to give a system clock output as close as
possible to, but not exceeding, 200 MHz. The internal blocks of
the AD6654 that run off the PLL clock are rated to run at a
maximum of 200 MHz. The default power-up state for the PLL
clock multiplier is the bypass state, where CLK is passed on as
the PLL clock.
ADC Gain Control
The DDC input port has individual, high speed gain control
logic circuitry. Such gain control circuitry is useful in applications that involve large dynamic-range inputs. The AD6654 gain
control logic allows programmable upper and lower thresholds
and a programmable dwell-time counter for temporal
hysteresis.
PLL CLOCK GENERATION
1
The DDC input port has a 3-bit output from the gain control
block. The operation is controlled by the gain control enable bit
in the gain control register of the DDC input port. Logic 1 in
this bit programs the EXP[2:0] pins as gain control outputs.
ADC_CLK
0
CLK
DIVIDE BY N
(1, 2, 4 OR 8)
PLL CLOCK
MULTIPLIER
(4x TO 20x)
0
PLL_CLK
1
Function
5
N
1 FOR BYPASS
M
05156-031
BYPASS_PLL
2
Figure 42. PLL Clock Generation
The PLL clock multiplier is programmable and uses the input
clock rates between 30 MHz and 92.16 MHz to give a system
clock rate (output) of as high as 200 MHz.
The output clock rate is given by
CLK × M
PLL _ CLK =
N
where:
CLK is the input port clock rate.
M is a 5-bit programmable multiplication factor.
The gain control block features a programmable upper threshold register and a lower threshold register. The ADC input data
is compared to both these registers. If ADC input data is larger
than the upper threshold register, then the gain control output
is decremented by 1. If the ADC input data is smaller than the
lower threshold register, then the gain control output is incremented by 1.
When decrementing the gain control output, the change is
immediate. But when incrementing the output, a dwell-time
register is used to delay the change. If the ADC input is larger
than the upper threshold register value, the gain control output
is immediately decremented to prevent overflow.
When the ADC input is lower than the lower threshold register,
a dwell timer is loaded with the value in the programmable
20-bit dwell-time register. The counter decrements once every
Rev. 0 | Page 29 of 88
AD6654
In a typical application, if the ADC signal goes below the lower
threshold for a time greater than the dwell time, then the gain
control output is incremented by 1. Gain control bits control the
gain ranging block, which appears before the ADC in the signal
chain. With each increment of the gain control output, gain in
the gain-ranging block is increased by 6.02 dB. This increases
the dynamic range of the input signal into the ADC by 6.02 dB.
This gain is compensated for in the AD6654 by relinearizing, as
explained in the Relinearization section. Therefore, the AD6654
can increase the dynamic range of the ADC by 42 dB, provided
that the gain-ranging block can support it.
Relinearization
The gain in the gain-ranging block (external) is compensated
for by relinearizing, using the exponent bits EXP[2:0] of the
input port. For this purpose, the gain control bits are connected
to the EXP[2:0] bits, providing an attenuation of 6.02 dB for
every increase in the gain control output. After the gain in the
external gain-ranging block and the attenuation in the AD6654
(using EXP bits), the signal gain is essentially unchanged. The
only change is the increase in the dynamic range of the ADC.
External gain-ranging blocks have a delay associated with
changing the gain of the signal. Typically, these delays can be
up to 14 clock cycles. The gain change in the AD6654 (via
EXP[2:0]) must be synchronized with the gain change in the
gain-ranging block (external). This is allowed in the AD6654 by
providing a flexible delay, programmable 6-bit word in the gain
control register. The value in this 6-bit word gives the delay in
input clock cycles. A programmable pipeline delay given by the
6-bit value (maximum delay of 63 clock cycles) is placed
between the gain control output and the EXP[2:0] input.
Therefore, the external gain-ranging block’s settling delays
are compensated for in the AD6654.
Note that any gain changes that are initiated during the relinearization period are ignored. For example, if the AD6654 detects
that a gain adjustment is required during the relinearization
period of a previous gain adjustment, then the new adjustment
is ignored.
Setting Up the Gain Control Block
To set up the gain control block for the input port, the individual upper threshold registers and lower threshold registers
should be written with appropriate values. The 10-bit values
written into upper and lower threshold registers are compared
to the 10 MSBs of the absolute magnitude calculated using the
input port data. The 20-bit dwell-time register should have the
appropriate number of clock cycles to provide temporal
hysteresis.
A 6-bit relinearization pipeline delay word is set to synchronize
with the settling delay in the external gain-ranging circuitry.
Finally, the gain control enable bit is written with Logic 1 to
activate the gain control block. On enabling, the gain control
output bits are made 000 (output on EXP[2:0] pins), which
represent the minimum gain for the external gain-ranging
circuitry and corresponding minimum attenuation during
relinearization. The normal functioning takes over, as explained
previously in this section.
FROM
MEMORY
MAP
UPPER
THRESHOLD
REGISTER
B
A
FROM INPUT
PORTS
B
FROM
MEMORY
MAP
Rev. 0 | Page 30 of 88
A
COMPARE
A>B
DECREASE
EXTERNAL GAIN
DEC
INCREASE
EXTERNAL GAIN
COMPARE
A<B
DWELL
TIMER
EXP GEN
EXP [2:0]
INC
LOWER
THRESHOLD
REGISTER
Figure 43. Gain Control Block Diagram
05156-032
input clock cycle, as long as the input signal remains below the
lower threshold register value. If the counter reaches 1, the gain
control output is incremented by 1. If the signal goes above the
lower threshold register value, the gain adjustment is not made,
and the normal comparison to lower and upper threshold
registers is initiated once again. Therefore, the dwell timer
provides temporal hysteresis and prevents the gain from
continuously switching.
AD6654
ADC INPUT PORT MONITOR FUNCTION
•
Peak power
•
Mean power
•
Number of samples crossing a threshold
FROM
MEMORY
MAP
POWER MONITOR
PERIOD REGISTER
DOWN
COUNTER
IS COUNT = 1?
TO
INTERRUPT
CONTROLLER
LOAD
FROM
INPUT
PORTS
CLEAR
MAGNITUDE
STORAGE
REGISTER
LOAD
POWER MONITOR
HOLDING
REGISTER
TO
MEMORY
MAP
LOAD
COMPARE
A>B
These functions are controlled via the 2-bit power monitor
function select bits in the power monitor control register of the
DDC input port. The DDC input port can be set for different
modes, but only one function can be active at a time. The three
modes of operation can function continuously over a programmable time period. This time period is programmed as the
number of input clock cycles in a 24-bit ADC monitor period
register (AMPR). An internal magnitude storage register (MSR)
is used to monitor, accumulate, or count, depending on the
mode of operation.
PEAK DETECTOR MODE
Control Bits 00
The magnitude of the input port signal is monitored over a
programmable time period (given by AMPR) to give the peak
value detected. This mode is set by programming Logic 0 in the
power monitor function select bits in the power monitor
control register of the DDC input port. The 24-bit AMPR must
be programmed before activating this mode.
After enabling this mode, the value in the AMPR is loaded into
a monitor period timer and the countdown is started. The
magnitude of the input signal is compared to the MSR, and the
greater of the two is updated back into the MSR. The initial
value of the MSR is set to the current ADC input signal magnitude. This comparison continues until the monitor period timer
reaches a count of 1.
When the monitor period timer reaches a count of 1, the value
in the MSR is transferred to the power monitor holding register,
which can be read through the microport or the serial port. The
monitor period timer is reloaded with the value in the AMPR,
and the countdown is started. Also, the magnitude of the first
input sample is updated in the MSR, and the comparison and
update procedure, as explained above, continues. If the
interrupt is enabled, an interrupt is generated, and the interrupt
status register is updated when the AMPR reaches a count of 1.
05156-033
The AD6654 provides a power monitor function that can
monitor the DDC input stream and gather statistics about the
received signal in a signal chain. This function block can
operate in one of three modes measuring the following over a
programmable period of time:
Figure 44. ADC Input Peak Detector Block Diagram
MEAN POWER MODE
Control Bits 01
In this mode, the magnitude of the input port signal is
integrated (by adding an accumulator) over a programmable
time period (given by AMPR) to give the integrated magnitude
of the input signal. This mode is set by programming Logic 1 in
the power monitor function select bits in the power monitor
control register of the DDC input port. The 24-bit AMPR,
representing the period over which integration is performed,
must be programmed before activating this mode.
After enabling this mode, the value in the AMPR is loaded into
a monitor period timer, and the countdown is immediately
started. The 15-bit magnitude of input signal is right-shifted by
nine bits to give 6-bit data. This 6-bit data is added to the
contents of a 24-bit holding register, thereby performing an
accumulation. The integration continues until the monitor
period timer reaches a count of 1.
When the monitor period timer reaches a count of 1, the value
in the MSR is transferred to the power monitor holding register
(after some formatting), which can be read through the microport or the serial port. The monitor period timer is reloaded
with the value in the AMPR, and the countdown is started.
Also, the first input sample signal magnitude is updated in the
MSR, and the accumulation continues with the subsequent
input samples. If the interrupt is enabled, an interrupt is
generated, and the interrupt status register is updated when the
AMPR reaches a count of 1. Figure 45 illustrates the mean
power monitoring logic.
The value in the MSR is a floating-point number with 4 MSBs
and 20 LSBs. If the 4 MSBs are EXP and the 20 LSBs are MAG,
the value in dBFS can be decoded using the following equation:
Figure 44 is a block diagram of the peak detector logic. The
MSR contains the absolute magnitude of the peak detected by
the peak detector logic.
Rev. 0 | Page 31 of 88
⎡⎛ MAG ⎞
⎤
MeanPower = 10 log ⎢⎜ 20 ⎟2 − (EXP − 1)⎥
⎠
⎣⎝ 2
⎦
AD6654
FROM
MEMORY
MAP
POWER MONITOR
PERIOD REGISTER
DOWN
COUNTER
IS COUNT = 1?
TO
INTERRUPT
CONTROLLER
LOAD
CLEAR
LOAD
POWER MONITOR
HOLDING
REGISTER
ACCUMULATOR
TO
MEMORY
MAP
05156-034
FROM
INPUT
PORTS
Figure 45. ADC Input Mean Power Monitoring Block Diagram
THRESHOLD CROSSING MODE
Control Bits 10
In this mode of operation, the magnitude of the input port
signal is monitored over a programmable time period (given
by AMPR) to count the number of times it crosses a certain
programmable threshold value. This mode is set by programming Logic 1x (where x is a don’t care bit) in the power monitor
function select bits in the power monitor control register of the
DDC input port. Before activating this mode, the user needs to
program the 24-bit AMPR and the 10-bit upper threshold register
of the DDC input port. The same upper threshold register is
used for both power monitoring and gain control (see the ADC
Gain Control section).
After entering this mode, the value in the AMPR is loaded into
a monitor period timer, and the countdown is started. The
magnitude of the input signal is compared to the upper
threshold register (programmed previously) on each input clock
cycle. If the input signal has a magnitude greater than the upper
threshold register, then the MSR register is incremented by 1.
The initial value of the MSR is set to 0. This comparison and
incrementing of the MSR register continues until the monitor
period timer reaches a count of 1.
When the monitor period timer reaches a count of 1, the value
in the MSR is transferred to the power monitor holding register,
which can be read through the microport or the serial port. The
monitor period timer is reloaded with the value in the AMPR,
and the countdown is started. The MSR register is also cleared
to a value of 0. If interrupts are enabled, an interrupt is generated, and the interrupt status register is updated when the
AMPR reaches a count of 1. Figure 46 illustrates the threshold
crossing logic. The value in the MSR is the number of samples
that have an amplitude greater than the threshold register.
FROM
MEMORY
MAP
POWER MONITOR
PERIOD REGISTER
DOWN
COUNTER
IS COUNT = 1?
TO
INTERRUPT
CONTROLLER
ADDITIONAL CONTROL BITS
For additional flexibility in the power monitoring process, two
control bits are provided in the power monitor control register.
The two control bits are the disable monitor period timer bit
and the clear-on-read bit. These options have the same function
in all three modes of operation.
Disable Monitor Period Timer Bit
When the disable monitor period timer bit is written with
Logic 1, the timer continues to run but does not cause the
contents of the MSR to be transferred to the holding register
when the count reaches 1. This function of transferring the
MSR to the power monitor holding register and resetting the
MSR is now controlled by a read operation on the microport or
serial port.
When a microport or serial port read is performed on the
power monitor holding register, the MSR value is transferred to
the holding register. After the read operation, the timer is
reloaded with the AMPR value. If the timer reaches 1 before the
microport or serial port read, the MSR value is not transferred
to the holding register, as in normal operation. The timer still
generates an interrupt on the AD6654 interrupt pin and updates
the interrupt status register. An interrupt appears on the IRP
pin, if interrupts are enabled in the interrupt enable register.
Clear-on-Read Bit
This control bit is valid only when the disable monitor period
timer bit is Logic 1. When both of these bits are set, a read
operation to either the microport or the serial port reads the
MSR value, and the monitor period timer is reloaded with the
AMPR value. The MSR is cleared (written with current input
signal magnitude in peak power and mean power modes;
written with a 0 in threshold crossing mode), and normal
operation continues.
When the monitor period timer is disabled and the clear-onread bit is set, a read operation to the power monitor holding
register clears the contents of the MSR and, therefore, the power
monitor loop restarts.
If the clear-on-read bit is Logic 0, the read operation to the
microport or serial port does not clear the MSR value after it is
transferred into the holding register. The value from the
previous monitor time period persists, and it continues to be
compared, accumulated, or incremented, based on new input
signal magnitude values.
LOAD
FROM
MEMORY
MAP
CLEAR
A COMPARE
A>B
COMPARE
A>B
LOAD
POWER MONITOR
HOLDING
REGISTER
TO
MEMORY
MAP
B
UPPER
THRESHOLD
REGISTER
05156-035
FROM
INPUT
PORTS
Figure 46. ADC Input Threshold Crossing Block Diagram
Rev. 0 | Page 32 of 88
AD6654
INPUT CROSSBAR MATRIX
The AD6654 has one ADC input port and six channels. Each
channel can individually select its input source from either the
real ADC input port, or from an internally generated pseudo
random sequence (referred to as a PN sequence) generator.
Each channel has an input crossbar matrix to facilitate selection
of the input signal source.
Each channel has a separate selection for individual control.
Cross bar mux selection enables each channel to select its input
signal source.
The selection of input signal for a particular channel is made
using a 4-bit cross bar mux select word in the ADC input
control register.
Table 14. Cross Bar Mux Selection Bits
Table 14 gives the valid combinations of cross bar mux select
values and the corresponding input signal selections.
Cross Bar Mux Select Bits
0010
0100
Rev. 0 | Page 33 of 88
Input Signal Selection
ADC input drives the channel.
Internal PN sequence drives the
channel.
AD6654
NUMERICALLY CONTROLLED OSCILLATOR (NCO)
Each channel consists of an independent complex NCO and a
complex mixer. This processing stage is comprised of a digital
tuner consisting of three multipliers and a 32-bit complex NCO.
The NCO serves as a quadrature local oscillator capable of
producing an NCO frequency of between –CLK/2 and +CLK/2
with a resolution of CLK/232 in the complex mode, where CLK
is the input clock frequency.
The NCO frequency word can be calculated using following the
equation:
The frequency word used for generating the NCO is a 32-bit
word. This word is used to generate a 20-bit phase word. A
16-bit phase offset word is added to this phase word. 18 bits of
this phase word are used to generate the sine and cosine of the
required NCO frequency. The amplitude of the sine and cosine
are represented using 17 bits. The worst-case spurious signal
from the NCO is better than −100 dBc for all output
frequencies.
NCO_FREQ is the 32-bit twos complement number representing the NCO frequency register.
Because all the filtering in the AD6654 is low-pass filtering, the
carrier of interest is tuned down to dc (frequency = 0 Hz). This
is illustrated in Figure 47. Once the signal of interest is tuned
down to dc, the unwanted adjacent carriers can be rejected
using the low-pass filtering that follows.
Note that this equation applies to the aliasing of signals in the
digital domain (that is, aliasing introduced when digitizing
analog signals).
NCO _ FREQ = 2 32
mod ( f CH , f CLK )
f CLK
where:
fCH is the desired carrier frequency.
fCLK is the clock rate for the channel under consideration.
mod( ) is a remainder function. For example, mod(110, 100) =
10 and, for negative numbers, mod(−32, 10) = −2.
For example, if the carrier frequency is 100 MHz and the clock
frequency is 80 MHz,
mod ( f CH , f DK )
NCO FREQUENCY
The NCO frequency value is given by the 32-bit twos complement number entered in the NCO frequency register.
Frequencies between −CLK/2 and +CLK/2 (with +CLK/2
excluded) are represented using this frequency word:
f CLK
=
20
= 0.25
80
This, in turn, converts to 0x4000 0000 in the 32-bit twos
complement representation for NCO_FREQ.
0x8000 0000 represents a frequency given by −CLK/2.
0x0000 0000 represents dc (frequency is 0 Hz).
0x7FFF FFFF represents CLK/2 − CLK/232.
WIDEBAND INPUT SPECTRUM (–fsample/2 TO +fsample/2)
SIGNAL OF INTEREST IMAGE
–fs/2
–7fs/16
–3fs/8
–5fs/16
SIGNAL OF INTEREST
–fs/4
–3fs/16
–fs/8
–fs/16
DC
fs/16
fs/8
3fs/16
fs/4
5fs/16
3fs/8
7fs/16
fs/2
5fs/16
3fs/8
7fs/16
fs/2
WIDEBAND INPUT SPECTRUM (30MHz FROM HIGH SPEED ADC)
NCO TUNES SIGNAL TO
–fs/2
–7fs/16
–3fs/8
–5fs/16
–fs/4
–3fs/16
–fs/8
–fs/16
DC
SIGNAL OF INTEREST IMAGE
fs/16
fs/8
3fs/16
fs/4
FREQUENCY TRANSLATION (SINGLE 1MHz CHANNEL TUNED TO BASEBAND)
Figure 47. Frequency Translation Principle Using the NCO and Mixer
Rev. 0 | Page 34 of 88
05156-036
SIGNAL OF INTEREST
AFTER FREQUENCY TRANSLATION
AD6654
If the carrier frequency is 70 MHz and the clock frequency is
80 MHz, then:
mod( f CH , f CLK ) 10
=
= 0.125
80
f CLK
This, in turn, converts to 0xE000 0000 in the twos complement
32-bit representation.
MIXER
The NCO is accompanied by a mixer. Its operation is similar to
an analog mixer. It performs the down-conversion of real input
signals by using the NCO frequency as a local oscillator. This
mixer performs a real mixer operation (with two multipliers).
The mixer adjusts its operation based on the input signal
provided to each individual channel.
BYPASS
The NCO and the mixer can be individually bypassed in each
channel by writing Logic 1 in the NCO bypass bit in the NCO
control register of the channel under consideration.
CLEAR PHASE ACCUMULATOR ON HOP
When clear, the NCO accumulator bit of the NCO control
register is set (Logic 1), the NCO phase accumulator is cleared
prior to a frequency hop. Refer to the Chip Synchronization
section for details on frequency hopping. This ensures a
consistent phase of the NCO on each hop. The NCO phase
offset is unaffected by this setting and is still in effect. If phasecontinuous hopping is needed, this bit should be cleared (NCO
accumulator is not cleared). The last phase in the NCO phase
register is the initiating point for the new frequency.
PHASE DITHER
The AD6654 provides a phase dither option for improving the
spurious performance of the NCO. Writing Logic 1 in the phase
dither enable bit of the NCO control register of individual
channels enables phase dither. When phase dither is enabled,
random phase is added to the LSBs of the phase accumulator of
the NCO. When phase dither is enabled, spurs due to phase
truncation in the NCO are randomized.
The energy from these spurs is spread into the noise floor and
the spurious free dynamic range is increased at the expense of a
very slight decrease in the SNR. The choice of whether to use
phase dither in a system is ultimately decided by the system
goals. If lower spurs are desired at the expense of a slightly
raised noise floor, phase dither should be employed. If a low
noise floor is desired and higher spurs can be tolerated or
filtered by subsequent stages, then phase dither is not needed.
AMPLITUDE DITHER
Amplitude dither can be used to improve spurious performance
of the NCO. Amplitude dither is enabled by writing Logic 1 in
the amplitude dither enable bit of the NCO control register of
the channel under consideration. Random amplitude is added
to the LSBs of the sine and cosine amplitudes, when this feature
is enabled. Amplitude dither improves performance by randomizing the amplitude quantization errors within the angular-toCartesian conversion of the NCO. This option might reduce
spurs at the expense of a slightly raised noise floor. Amplitude
dither and phase dither can be used together, separately, or not
at all.
NCO FREQUENCY HOLD-OFF REGISTER
When the NCO frequency registers are written by the microport or serial port, data is passed to a shadow register. Data can
be moved to the main registers when the channel comes out of
sleep mode, or when a sync hop occurs. In either event, a
counter can be loaded with the NCO frequency hold-off
register value. The 16-bit unsigned integer counter starts
counting down, clocked by the input port clock selected at the
crossbar mux. When the counter reaches 0, the new frequency
value in the shadow register is written to the NCO frequency
register. Writing 1 in this hold-off register updates the NCO
frequency register as soon as the start sync or hop sync occurs.
See the Chip Synchronization section for details.
PHASE OFFSET
The phase offset register can be written with a value that is
added as an offset to the phase accumulator of the NCO. This
16-bit register is interpreted as a 16-bit unsigned integer. A
0x0000 in this register corresponds to a 0 radian offset and a
0xFFFF corresponds to an offset of 2π × (1 − 1/216) radians.
This register allows multiple NCOs (multiple channels) to be
synchronized to produce complex sinusoids with a known and
steady phase difference.
HOP SYNC
A hop sync should be issued to the channel, when the NCO
frequency of that channel needs to be changed from one
frequency to another. See the Chip Synchronization section for
details.
Rev. 0 | Page 35 of 88
AD6654
FIFTH-ORDER CIC FILTER
The signal processing stage immediately after the NCO is a CIC
filter stage. This stage implements a fixed coefficient, decimating, cascade integrated comb filter. The input rate to this filter is
the same as the data rate at the input port; the output rate from
this stage is dependent on the decimation factor.
f CIC =
f IN
M CIC
The decimation ratio, MCIC, can be programmed from 2 to 32
(only integer values). The 5-bit word in the CIC decimation
register is used to set the CIC decimation factor. A binary value
of one less than the decimation factor is written into this
register. The decimation ratio of 1 can be achieved by bypassing
the CIC filter stage. The frequency response of the filter is given
by the following equations. The gain and pass-band droop of
the CIC should be calculated by these equations. Both parameters can be offset in the RCF stage.
− MCIC
⎛1− Z
1
H (z ) = (S +5) × ⎜⎜
−1
CIC
2
⎝ 1− Z
H( f ) =
(SCIC + 5)
5
where:
fIN is the data input rate to the channel under consideration.
SCIC, the scale factor, is a programmable unsigned integer
between 0 and 20.
The attenuation of the data into the CIC stage should be controlled in 6 dB increments. For the best dynamic range, SCIC
should be set to the smallest value possible (lowest attenuation
possible) without creating an overflow condition. This can be
accomplished safely using the following equation, where
input_level is the largest possible fraction of the full-scale value
at the input port. This value is output from the NCO stage and
pipelined into the CIC filter.
SCIC = ceil (log 2 (M CIC 5 × input _ level )) − 5
OLCIC =
(M
2
CIC REJECTION
Table 15 illustrates the amount of bandwidth as a percentage of
the data rate into the CIC stage, which can be protected with
various decimation rates and alias rejection specifications. The
maximum input rate into the CIC is 150 MHz (the same as the
maximum input port data rate). The data can be scaled to any
other allowable sample rate.
Table 15 can be used to decide the minimum decimation
required in the CIC stage to preserve a certain bandwidth. The
CIC5 stage can protect a much wider bandwidth to any given
rejection, when a decimation ratio lower than that identified in
the table is used. The table helps to calculate an upper boundary
on decimation, MCIC, given the desired filter characteristics.
Table 15. SSB CIC5 Alias Rejection Table (fIN = 1)
5
⎛
⎛M
⎞⎞
⎜ SIN ⎜ CIC × f ⎟ ⎟
⎜ f
⎟⎟
⎜
IN
⎝
⎠⎟
×⎜
⎜
⎟
⎛
⎞
f
⎟ ⎟
⎜ SIN ⎜⎜ π
⎟
⎜
⎝ f IN ⎠ ⎟⎠
⎝
1
2
⎞
⎟
⎟
⎠
not performed. In bypass mode, the output of the CIC filter is
the same as the input of the CIC filter.
) × input _ level
5
CIC
SCIC + 5
BYPASS
The fifth-order CIC filter can be bypassed when no decimation
is required of it. When it is bypassed, the scaling operation is
MCIC5
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Rev. 0 | Page 36 of 88
−60 dB
8.078
6.367
5.022
4.107
3.463
2.989
2.627
2.342
2.113
1.924
1.765
1.631
1.516
1.416
1.328
1.250
1.181
1.119
1.064
1.013
0.967
0.925
0.887
0.852
0.819
0.789
0.761
0.734
0.710
0.687
0.666
−70 dB
6.393
5.110
4.057
3.326
2.808
2.425
2.133
1.902
1.716
1.563
1.435
1.326
1.232
1.151
1.079
1.016
0.960
0.910
0.865
0.824
0.786
0.752
0.721
0.692
0.666
0.641
0.618
0.597
0.577
0.559
0.541
−80 dB
5.066
4.107
3.271
2.687
2.270
1.962
1.726
1.540
1.390
1.266
1.162
1.074
0.998
0.932
0.874
0.823
0.778
0.737
0.701
0.667
0.637
0.610
0.584
0.561
0.540
0.520
0.501
0.484
0.468
0.453
0.439
−90 dB
4.008
3.297
2.636
2.170
1.836
1.588
1.397
1.247
1.125
1.025
0.941
0.870
0.809
0.755
0.708
0.667
0.630
0.597
0.568
0.541
0.516
0.494
0.474
0.455
0.437
0.421
0.406
0.392
0.379
0.367
0.355
−100 dB
3.183
2.642
2.121
1.748
1.480
1.281
1.128
1.007
0.909
0.828
0.760
0.703
0.653
0.610
0.572
0.539
0.509
0.483
0.459
0.437
0.417
0.399
0.383
0.367
0.353
0.340
0.328
0.317
0.306
0.297
0.287
AD6654
EXAMPLE CALCULATIONS
Goal: Implement a filter with an input sample rate of 100 MHz
requiring 100 dB of alias rejection for a ±1.4 MHz pass band.
Solution: First determine the percentage of the sample rate that
is represented by the pass band.
BW FRACTION = 100 ×
1.4 MHz
= 1.4
100 MHz
In the −100 dB column in Table 15, find the value greater than
or equal to the pass-band percentage of the clock rate. Then
find the corresponding rate decimation factor (MCIC). For an
MCIC of 6, the frequency that has −100 dB of alias rejection is
1.48%, which is slightly larger than the 1.4% calculated.
Therefore, for this example, the maximum bound on CIC
decimation rate is 6. A higher MCIC means less alias rejection
than the 100 dB required.
Rev. 0 | Page 37 of 88
AD6654
FIR HALF-BAND BLOCK
The output of the CIC filter is pipelined into the FIR HB (halfband) block. Each channel has two sets of cascading fixed
coefficient FIR and fixed coefficient half-band filters. The halfband filters decimate by 2. Each of these filters (FIR1, HB1,
FIR2, and HB2) is described in the following sections.
3-TAP FIXED COEFFICIENT FILTER (FIR1)
The 3-tap FIR filter is useful in certain filter configurations in
which extra alias protection is needed for the decimating HB1
filter. It is a simple sum-of-products FIR filter with three filter
taps and 2-bit fixed coefficients. Note that this filter does not
decimate. The coefficients of this symmetric filter are {1, 2, 1}.
The normalized coefficients used in the implementation are
{0.25, 0.5, 0.25}.
The user can either use or bypass this filter. Writing Logic 0 to
the FIR1 enable bit in the FIR-HB control register bypasses this
fixed coefficient filter. The filter is useful only in certain filter
configurations and bypassing it for other applications results in
power savings.
0
0.34
–8.33
0.66
FIR1 RESPONSE
–16.67
–25.00
–33.33
dBc
–41.67
–50.00
DECIMATE-BY-2 HALF-BAND FILTER (HB1)
The next stage of the FIR-HB block is a decimate-by-2 halfband filter. The 11-tap, symmetrical, fixed coefficient HB1 filter
has low power consumption due to its polyphase implementation. The filter has 22 bits of input and output data with 10-bit
coefficients. Table 16 lists the coefficients of the half-band filter.
The normalized coefficients used in the implementation and
the 10-bit decimal equivalent value of the coefficients are also
listed. Other coefficients are 0s.
Table 16. Fixed Coefficients for HB1 Filter
Coefficient
Number
C1, C11
C3, C9
C5, C7
C6
Normalized
Coefficient
0.013671875
−0.103515625
0.58984375
1
Decimal Coefficient
(10-Bit)
7
−53
302
512
Similar to the FIR1 filter, this filter can be used or bypassed.
Writing Logic 0 to the HB1 enable bit in the FIR-HB control
register bypasses this fixed coefficient HB filter. The filter is
useful only in certain filter configurations and bypassing it for
other applications results in power savings. For example, it is
useful in narrow-band and wideband output applications in
which more filtering is required, as compared to very wide
bandwidth applications in which a higher output rate might
prohibit the use of a decimating filter. The response of the filter
is shown in Figure 49.
–58.33
The input sample rate of this filter is the same as the CIC filter
output rate and is given by
–66.67
–75.00
–81
–83.33
f HB1 =
–100.00
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
FRACTION OF FIR1 INPUT SAMPLE RATE
0.9
05156-037
–91.67
Figure 48. FIR1 Filter Response to the Input Rate of the Filter
This filter runs at the same sample rate as the CIC filter output
rate and is given by
f FIR1 =
f IN
M CIC
where:
fIN is the input rate to the channel.
MCIC is the decimation ratio in the CIC filter stage.
0
0.43
0.57
–10
f IN
M CIC
–20
–30
–40
–50
dBc
HB1 RESPONSE
–60
–70
–77
–80
The maximum input and output rates for this filter are
150 MHz.
–90
–100
–110
–120
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
FRACTION OF HB1 INPUT SAMPLE RATE
0.9
Figure 49. HB1 Filter Response to the Input Rate of the Filter
Rev. 0 | Page 38 of 88
05156-038
where:
fIN is the input rate to the channel.
MCIC is the decimation ratio in the CIC filter stage.
AD6654
The filter has a maximum input sample rate of 150 MHz and,
when filter is not bypassed, the maximum output rate is
75 MHz.
The filter has a ripple of 0.0012 dB and rejection of 77 dB. For
an alias rejection of 77 dB, the alias-protected bandwidth is 14%
of the filter input sample rate. The bandwidth of the filter for a
ripple of 0.00075 dB is also the same as the alias-protected
bandwidth, due to the nature of half-band filters. The 3 dB
bandwidth of this filter is 44% of the filter input sample rate.
For example, if the sample rate into the filter is 50 MHz, then
the alias-protected bandwidth of the HB1 filter is 7 MHz. If the
bandwidth of the required carrier is greater than 7 MHz, then
HB1 might not be useful.
0.43
fFIR2 = fHB1, if HB1 is bypassed
fFIR2 =
fHB1 is the input rate of the HB1 filter.
fFIR2 is the input rate of the FIR2 filter.
The maximum input and output rate for this filter is 75 MHz.
The response of the FIR2 filter is shown in Figure 51.
0
0.57
–10
–8.33
–20
–16.67
–30
–25.00
–40
–33.33
–50
–41.67
–60
–50.00
–70
FIR1 + HB1 RESPONSE
–80
f HB1
, if HB1 is not bypassed
2
where:
dBc
0.39
0.61
FIR2 RESPONSE
–30
–58.33
–66.67
–75.00
–90
–100
–83.33
–107
–91.67
–120
–100.00
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
FRACTION OF HB1 INPUT SAMPLE RATE
0.9
05156-039
–110
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
FRACTION OF FIR2 INPUT SAMPLE RATE
0.9
05156-040
dBc
0
This filter runs at a sample rate given by one of the following
equations:
Figure 51. FIR2 Filter Response to the Input Rate of the Filter
Figure 50. Composite Response of FIR1 and HB1 Filters to Their Input Rate
6-TAP FIXED COEFFICIENT FILTER (FIR2)
DECIMATE-BY-2 HALF-BAND FILTER (HB2)
Following the first cascade of the FIR1 and HB1 filters is the
second cascade of the FIR2 and HB2 filters. The 6-tap, fixed
coefficient FIR2 filter is useful in providing extra alias
protection for the decimating HB2 filter in certain filter
configurations. It is a simple sum-of-products FIR filter with
six filter taps and 5-bit fixed coefficients. Note that this filter
does not decimate. The normalized coefficients used in the
implementation and the 5-bit decimal equivalent value of the
coefficients are listed in Table 17.
The second stage of the second cascade of the FIR-HB block is a
decimate-by-2 half-band filter. The 27-tap, symmetric, fixed
coefficient HB2 filter has low power consumption due to its
polyphase implementation. The filter has 20 bits of input and
output data with 12-bit coefficients. The normalized
coefficients used in the implementation and the 10-bit decimal
equivalent value of the coefficients are listed in Table 18. Other
coefficients are 0s.
Table 17. 6-Tap FIR2 Filter Coefficients
Coefficient
Number
C1, C27
Normalized
Coefficient
0.00097656
Decimal Coefficient
(12-Bit)
2
C3, C25
C5, C23
C7, C21
C9, C19
C11, C17
C13, C15
C14
−0.00537109
0.015
−0.0380859
0.0825195
−0.1821289
0.6259766
1
−11
32
−78
169
−373
1282
2048
Coefficient
Number
C0, C5
C1, C4
Normalized
Coefficient
−0.125
0.1875
Decimal Coefficient
(5-Bit)
−2
3
C2, C3
0.9375
15
The user can either use or bypass this filter. Writing Logic 0 to
FIR2 enable bit in the FIR-HB control register bypasses this
fixed coefficient filter. The filter is useful only in certain filter
configurations and bypassing it for other applications results in
power savings. The filter is especially useful in increasing the
stop-band attenuation of the HB2 filter that follows. Therefore,
it is optimal to use both FIR2 and HB2 in a configuration.
Table 18. HB2 Filter Fixed Coefficients
Similar to the HB1 filter, this filter can either be used or
bypassed. Writing Logic 0 to the HB1 enable bit in the FIR-HB
Rev. 0 | Page 39 of 88
AD6654
control register bypasses this fixed coefficient HB filter. The
filter is useful only in certain filter configurations and bypassing
it for other applications results in power savings. For example,
the filter is useful in narrow-band applications in which more
filtering is required, as compared to wide-band applications, in
which a higher output rate might prohibit the use of a decimating filter. The response of the HB2 filter is shown in Figure 52.
0.01
0.34
0.66
–9.99
–19.99
–29.99
–39.99
–60.00
The filter has a ripple of 0.00075 dB and rejection of 81 dB. For
an alias rejection of 81 dB, the alias-protected bandwidth is 33%
of the filter input sample rate. The bandwidth of the filter for a
ripple of 0.00075 dB is the same as alias-protected bandwidth,
due to the nature of half-band filters. The 3 dB bandwidth of
this filter is 47% of the filter input sample rate. For example, if
the sample rate into the filter is 25 MHz, then the aliasprotected bandwidth of the HB2 filter is 8.25 MHz (33% of
25 MHz). If the bandwidth of the required carrier is greater
than 8.25 MHz, then HB2 might not be useful.
0.01
–65
–70.00
–80.00
0.66
–19.99
HB2 RESPONSE
–29.99
–90.00
–39.99
–100.00
–49.99
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
FRACTION OF HB2 INPUT SAMPLE RATE
0.9
dBc
0
05156-041
–110.00
–120.00
0.34
–9.99
–60.00
–80.00
Figure 52. HB2 Filter Response to the Input Rate of the Filter
–90.00
The filter input sample rate is the same as the FIR2 filter output
rate and is given by one of the following equations:
–100.00
–120.00
f HB1
, if HB1 is not bypassed
2
–90
–110.00
fHB2 = fFIR2 = fHB1, if HB1 is bypassed
fHB2 = fFIR2 =
FIR2 + HB2
RESPONSE
–70.00
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
FRACTION OF HB2 INPUT SAMPLE RATE
0.9
05156-042
dBc
–49.99
The input to the filter has a maximum of 75 MHz. The
maximum output rate when not bypassed is 37.5 MHz.
Figure 53. Composite Response of FIR2 and HB2 Filters to Their Input Rates
where:
fFIR2 is the input rate of the FIR2 filter.
fHB2 is the input rate of the HB2 filter.
fHB1 is the input rate of the HB1 filter.
Rev. 0 | Page 40 of 88
AD6654
INTERMEDIATE DATA ROUTER
Following the FIR-HB cascade filters is the intermediate data
router. This data router consists of muxes that allow the I and Q
data from any channel front end (input port + NCO + CIC +
FIRHB) to be processed by any channel back end (MRCF +
DRCF + CRCF). The choice of channel front end is made by
programming a 3-bit MRCF data select word in the MRCF
control register. The valid values for this word and their
corresponding settings are listed in Table 19.
Allowing different channel back ends to select different channel
front ends is useful in the polyphase implementation of filters.
When multiple AD6654 channels are used to process a single
carrier, a single-channel front end feeds more than one channel
back end. After processing through the channel back ends (RCF
filters), the data is interleaved back from all the polyphased
channels.
Table 19. Data Router Select Settings
MRCF Data Select[2:0]
000
001
010
011
1x0
1x1
Data Source
Channel 0
Channel 1
Channel 2
Channel 3
Channel 4
Channel 5
Rev. 0 | Page 41 of 88
AD6654
MONO-RATE RAM COEFFICIENT FILTER (MRCF)
The MRCF is a programmable sum-of-products FIR filter. This
filter block comes after the first data router and before the
DRCF and CRCF programmable filters. It consists of a maximum of eight taps with 6-bit programmable coefficients. Note
that this block does not decimate and is used as a helper filter
for the DRCF and CRCF filters that follow in the signal chain.
Because this filter is nondecimating, the input and output rates
are both the same and equal to one of the following:
fMRCF = fHB2, if HB2 is not bypassed
fMRCF =
f HB2
, if HB2 is not bypassed
2
The number of filter taps that are to be calculated is programmable using the 3-bit number-of-taps word in the MRCF
control register of the channel under consideration. The 3-bit
word programmed is one less than the number of filter taps.
The coefficients themselves are programmed in eight MRCF
coefficient memory registers for individual channels. The input
and output data to the block are both 20-bit.
then half of the PLL clock can be used for processing (power
savings). Otherwise, the PLL clock should be used.
SYMMETRY
BYPASS
Though the MRCF filter does not require symmetrical filters, if
the filter is symmetrical, then the symmetry bit in the MRCF
control register should be set. When this bit is set, only half of
the impulse response needs to be programmed into the MRCF
coefficient memory registers. For example, if the number of
filter taps is equal to five or six and the filter is symmetrical,
then only three coefficients need to be written into the coefficient memory. For both symmetrical and asymmetrical filters,
the number of filter taps is limited to eight.
The MRCF filter can be used in normal operation or bypassed
using the MRCF bypass bit in the MRCF control register. When
the filter is bypassed, the output of the filter is the same as the
input of the filter. Bypassing the MRCF filter when not required
results in power savings.
CLOCK RATE
The MRCF filter runs on an internal high speed PLL clock. This
clock rate can be as high as 200 MHz. If the half clock rate bit in
the MRCF control register is set, then only half the PLL clock
rate is used (maximum of 100 MHz). This results in power
savings, but can only be used if certain conditions are met.
If fPLLCLK is the PLL clock and if
fMRCF × NTAPS <=
f PLLCLK
,
2
SCALING
The output of the MRCF filter can be scaled by using the 2-bit
MRCF scaling word in the MRCF control register. Table 20
shows the valid values for the 2-bit word and their
corresponding settings.
Table 20. MRCF Scaling Factor Settings
MRCF Scale Word[1:0]
00
01
10
11
Rev. 0 | Page 42 of 88
Scaling Factor
18.06 dB attenuation
12.04 dB attenuation
6.02 dB attenuation
No scaling, 0 dB
AD6654
DECIMATING RAM COEFFICIENT FILTER (DRCF)
Following the MRCF is the programmable DRCF FIR filter.
This filter can calculate up to 64 asymmetrical filter taps or up
to 128 symmetrical filter taps. The filter is also capable of a
programmable decimation rate from 1 to 16. A flexible
coefficient offset feature allows loading multiple filters into the
coefficient RAM and changing the filters on the fly. The
decimation phase feature allows a polyphase implementation,
where multiple AD6654 channels are used for processing a
single carrier.
The DRCF filter has 20-bit input and output data and 14-bit
coefficient data. The number of filter taps to calculate is
programmable and is set in the DRCF taps register. The value
of the number of taps minus one is written to this register.
For example, a value of 19 in the register corresponds to
20 filter taps.
COEFFICIENT OFFSET
More than one set of filter coefficients can be loaded into
coefficient RAM at any given time (given sufficient RAM
space). The coefficient offset can be used in this case to access
the two or more different filters. By changing the coefficient
offset, the filter coefficients being accessed can be changed on
the fly. This decimal offset value is programmed in the DRCF
coefficient offset register. When this value is changed during the
calculation of a particular output data sample, the sample
calculation is completed using the old coefficients, and the new
coefficient offset from the next data sample calculation is used.
DECIMATION PHASE
The decimation rate is programmable using the 4-bit DRCF
decimation rate word in the DRCF control register. Again, the
value written is the decimation rate minus one.
When more than one channel of AD6654 is used to process one
carrier, polyphase implementation of corresponding channels’
DRCF or CRCF is possible using the decimation phase feature.
This feature can be used only under certain conditions. The
decimation phase is programmed using the 4-bit DRCF
decimation phase word of the DRCF control register.
BYPASS
MAXIMUM NUMBER OF TAPS CALCULATED
The DRCF filter can be used in normal operation or bypassed
using the DRCF bypass bit in the DRCF control register. When
the DRCF filter is bypassed, no scaling is applied and the output
of the filter is the same as the input to the DRCF filter.
The output rate of the DRCF filter is given by
SCALING
where:
The output of the DRCF filter can be scaled using the 2-bit
DRCF scaling word in the DRCF control register. Table 21 lists
the valid values for the 2-bit word and their corresponding
settings.
fMRCF is the data rate out of the MRCF filter and into the DRCF
filter.
MDRCF is the decimation rate in the DRCF filter.
f MRCF
M DRCF
The DRCF filter consists of two multipliers (one each for the
I and Q paths). Each multiplier, working at the high speed clock
rate (PLL clock), can do one multiply (or one tap) per high
speed clock cycle. Therefore, the maximum number of filter
taps that can be calculated (symmetrical or asymmetrical filter)
is given by
Table 21. DRCF Scaling Factor Settings
DRCF Scale Word[1:0]
00
01
10
11
f DRCF =
Scaling Factor
18.06 dB attenuation
12.04 dB attenuation
6.02 dB attenuation
No scaling, 0 dB
⎛ f PLLCLK
⎝ f DRCF
Maximum Number of Taps = ceil ⎜⎜
SYMMETRY
The DRCF filter does not require symmetrical filters. However,
if the filter is symmetrical, then the symmetry bit in the DRCF
control register should be set. When this bit is set, only half of
the impulse response needs to be programmed into the DRCF
coefficient memory registers. For example, if the number of
filter taps is equal to 15 or 16 and the filter is symmetrical, then
only eight coefficients need to be written into the coefficient
memory. Because a total of 64 taps can be written into the
memory registers, the DRCF can perform 64 asymmetrical
filter taps or 128 symmetrical filter taps.
⎞
⎟ −1
⎟
⎠
where:
fPLLCLK is the high speed internal processing clock generated by
the PLL clock multiplier.
fDRCF is the output rate of the DRCF filter, previously calculated.
Rev. 0 | Page 43 of 88
AD6654
PROGRAMMING DRCF REGISTERS FOR
AN ASYMMETRICAL FILTER
PROGRAMMING DRCF REGISTERS FOR A
SYMMETRIC FILTER
To program the DRCF registers for an asymmetrical filter:
To program the DRCF registers for a symmetrical filter:
1.
Write NTAPS – 1 in the DRCF taps register, where
NTAPS is the number of filter taps. The absolute
maximum value for NTAPS is 64 in asymmetrical filter
mode.
1.
Write NTAPS – 1 in the DRCF taps register, where
NTAPS is the number of filter taps. The absolute
maximum value for NTAPS is 128 in symmetric filter
mode.
2.
Write 0 for the DRCF coefficient offset register.
2.
3.
Write 0 for the symmetrical filter bit in the DRCF control
register.
Write ceil(64 – NTAPS/2) for the DRCF coefficient offset
register, where the ceil function takes the closest integer
greater than or equal to the argument.
4.
Write the start address for the coefficient RAM, typically
equal to the coefficient offset register in the DRCF start
address register.
3.
Write 1 for the symmetrical filter bit in the DRCF control
register.
4.
Write the start address for the coefficient RAM, typically
equal to coefficient offset register, in the DRCF start
address register.
5.
Write the stop address for the coefficient RAM, typically
equal to ceil(NTAPS/2) – 1, in the DRCF stop address
register.
6.
Write all coefficients to the DRCF coefficient memory
register, starting with the middle of the filter and working
towards the end of the filter. When coefficients are
numbered 0 to NTAPS – 1, the middle coefficient is given
by the coefficient number ceil(NTAPS/2). If in 8-bit
microport mode or serial port mode, write the lower byte
of the memory register first and then the higher byte.
After each write access to the DRCF coefficient memory
register, the internal RAM address is incremented starting
with the start address and ending with the stop address.
5.
In the DRCF stop address register, write the stop address
for the coefficient RAM, typically equal to the following:
Coefficient Offset + NTAPS − 1
6.
Write all coefficients in reverse order (start with last
coefficient) to the DRCF coefficient memory register. If in
8-bit microport mode or serial port mode, write the lower
byte of the memory register first and then the higher byte.
After each write access to the DRCF coefficient memory
register, the internal RAM address is incremented starting
with the start address and ending with the stop address.
Note that each write or read access increments the internal
RAM address. Therefore, all coefficients should be read first
before reading them back. Also, for debugging purposes, each
RAM address can be written individually by making the start
and stop addresses the same. Therefore, to program one RAM
location, the user writes the address of the RAM location to
both the start and stop address registers, and then writes the
coefficient memory register.
Note that each write or read access increments the internal
RAM address. Therefore, all coefficients should be read first
before reading them back. Also, for debugging purposes, each
RAM address can be written individually by making the start
and stop addresses the same. Therefore, to program one RAM
location, the user writes the address of the RAM location to
both the start and stop address registers, and then writes the
coefficient memory register.
Rev. 0 | Page 44 of 88
AD6654
CHANNEL RAM COEFFICIENT FILTER (CRCF)
Following the DRCF is the programmable decimating CRCF
FIR filter. The only difference between the DRCF and CRCF
filters is the coefficient bit width. The DRCF has 14-bit
coefficients, while the CRCF has 20-bit coefficients.
Because a total of 64 taps can be written into the memory
registers, the CRCF can perform 64 asymmetrical filter taps or
128 symmetrical filter taps.
This filter can calculate up to 64 asymmetrical filter taps or up
to 128 symmetrical filter taps. The filter is capable of a
programmable decimation rate from 1 to 16. The flexible
coefficient offset feature allows loading multiple filters into the
coefficient RAM and changing the filters on the fly. The
decimation phase feature allows for a polyphase implementation in which multiple AD6654 channels are used to process a
single carrier.
More than one set of filter coefficients can be loaded into the
coefficient RAM at any time (given sufficient RAM space). The
coefficient offset can be used in this case to access the two or
more different filters. By changing the coefficient offset, the
filter coefficients being accessed can be changed on the fly.
This decimal offset value is programmed in the CRCF
coefficient offset register. When this value is changed during
the calculation of a particular output data sample, the sample
calculation is completed using the old coefficients and the new
coefficient offset is brought into effect from the next data
sample calculation.
The CRCF filter has 20-bit input and output data and 20-bit
coefficient data. The number of filter taps to calculate is
programmable and is set in the CRCF taps register. The value
of the number of taps minus one is written to this register. For
example, a value of 19 in the register corresponds to 20 filter
taps. The decimation rate is programmable using the 4-bit
CRCF decimation rate word in the CRCF control register.
Again, the value written is the decimation rate minus one.
BYPASS
The CRCF filter can be used in normal operation or bypassed
using the CRCF bypass bit in the CRCF control register. When
the CRCF filter is bypassed, no scaling is applied and the output
of the filter is the same as the input to the CRCF filter.
COEFFICIENT OFFSET
DECIMATION PHASE
When more than one channel of the AD6654 is used to process
one carrier, polyphase implementation of the corresponding
channels’ DRCF or CRCF is possible using the decimation
phase feature. This feature can be used only under certain
conditions. The decimation phase is programmed using the
4-bit CRCF decimation phase word of the CRCF control
register.
MAXIMUM NUMBER OF TAPS CALCULATED
The output rate of the CRCF filter is given by
SCALING
The output of the CRCF filter can be scaled using the 2-bit
CRCF scaling word in the CRCF control register. Table 22
shows the valid values for the 2-bit word and the corresponding
settings. | ∑COEFF | is the sum of all coefficients (in normalized
form) used to calculate the FIR filter.
Table 22. CRCF Scaling Factor Settings
CRCF Scale Word[1:0]
00
01
10
11
Scaling Factor
18.06 dB attenuation
12.04 dB attenuation
6.02 dB attenuation
No scaling, 0 dB
f CRCF =
f DRCF
M CRCF
where:
fDRCF is the data rate out of the DRCF filter and into the CRCF
filter.
MCRCF is the decimation rate in the CRCF filter.
The CRCF filter consists of two multipliers (one each for the
I and Q paths). Each multiplier, working at the high speed clock
rate (PLL clock), can multiply (or tap once). Therefore, the
maximum number of filter taps that can be calculated
(symmetrical or asymmetrical filter) is given by
SYMMETRY
The CRCF filter does not require symmetrical filters. However,
if the filter is symmetrical, then the symmetry bit in the CRCF
control register should be set. When this bit is set, only half the
impulse response needs to be programmed into the CRCF
coefficient memory registers. For example, if the number of
filter taps is equal to 15 or 16 and the filter is symmetric, then
only eight coefficients need to be written into the coefficient
memory.
⎛ f PLLCLK
⎝ f CRCF
Maximum Number of Taps = ceil ⎜⎜
⎞
⎟ −1
⎟
⎠
fPLLCLK is the high speed internal processing clock generated by
the PLL clock multiplier.
fCRCF is the output rate of the CRCF filter as previously
calculated.
Rev. 0 | Page 45 of 88
AD6654
PROGRAMMING CRCF REGISTERS FOR AN
ASYMMETRICAL FILTER
PROGRAMMING CRCF REGISTERS FOR A
SYMMETRICAL FILTER
To program the CRCF registers for an asymmetrical filter:
To program the CRCF registers for a symmetrical filter:
1.
Write NTAPS – 1 in the CRCF taps register, where NTAPS
is the number of filter taps. The absolute maximum value
for NTAPS is 64 in asymmetrical filter mode.
1.
Write NTAPS – 1 in the CRCF taps register, where NTAPS
is the number of filter taps. The absolute maximum value
for NTAPS is 128 in symmetrical filter mode.
2.
Write 0 for the CRCF coefficient offset register.
2.
3.
Write 0 for the symmetrical filter bit in the CRCF control
register.
Write ceil(64 – NTAPS/2) for the CRCF coefficient offset
register, where the ceil function takes the closest integer
greater than or equal to the argument.
4.
In the CRCF start address register, write the start address
for the coefficient RAM, typically equal to the coefficient
offset register.
3.
Write 1 for the symmetrical filter bit in the CRCF control
register.
4.
In the CRCF start address register, write the start address
for the coefficient RAM, typically equal to the coefficient
offset register.
5.
In the CRCF stop address register, write the stop address
for the coefficient RAM, typically equal to
ceil(NTAPS/2) – 1.
6.
Write all coefficients to the CRCF coefficient memory
register, starting with middle of the filter and working
towards the end of the filter. When coefficients are
numbered 0 to NTAPS – 1, the middle coefficient is given
by the coefficient number ceil(NTAPS/2). In 8-bit
microport mode or serial port mode, write the lower byte
of the memory register first and then the higher byte. In
16-bit microport mode, write the lower 16-bits of the
CRCF memory register first and then the high four bits.
After each write access to the CRCF coefficient memory
register, the internal RAM address is incremented starting
with the start address and ending with the stop address.
5.
In the CRCF stop address register, write the stop address
for the coefficient RAM, typically equal to the following:
Coefficient Offset + NTAPS – 1
6.
Write all coefficients in reverse order (start with last
coefficient) to the CRCF coefficient memory register. In
8 bit microport mode or serial port mode, write the lower
byte of the memory register first and then the higher byte.
In 16-bit microport mode, write the lower 16-bits of the
CRCF memory register first and then the high four bits.
After each write access to the CRCF coefficient memory
register, the internal RAM address is incremented starting
with the start address and ending with the stop address.
Note that each write or read access increments the internal
RAM address. Therefore, all coefficients should be read first
before reading them back. Also, for debugging purposes, each
RAM address can be written individually by making the start
and stop addresses the same. Therefore, to program one RAM
location, the user writes the address of the RAM location to
both the start and stop address registers, and then writes the
coefficient memory register.
Note that each write or read access increments the internal
RAM address. Therefore, all coefficients should be read first
before reading them back. Also, for debugging purposes, each
RAM address can be written individually by making the start
and stop addresses the same. Therefore, to program one RAM
location, the user writes the address of the RAM location to
both the start and stop address registers, and then writes the
coefficient memory register.
Rev. 0 | Page 46 of 88
AD6654
INTERPOLATING HALF-BAND FILTER
The AD6654 has interpolating half-band FIR filters that
immediately follow the CRCF programmable FIR filters and
precede the second data router. Each interpolating half-band
filter takes 22-bit I and 22-bit Q data from the preceding CRCF
and outputs rounded 22-bit I and 22-bit Q data to the second
data router. A 10-tap fixed coefficient filter is implemented in
this stage. The maximum input rate into this block is 17 MHz.
Consequently, the maximum output is constrained to 34 MHz.
The normalized coefficients used in the implementation and
the 10-bit decimal equivalent value of the coefficients are listed
in Table 23. Other coefficients are 0.
The image rejection of this filter is about 55 dB, but is sufficient
because the image is from the desired signal, not an interfering
signal. Note that the interpolating half-band filter can be
enabled by writing Logic 1 to Bit 9 of the MRCF control
registers.
The frequency response of the interpolating half-band FIR is
shown in Table 23 with respect to the chip rate. The input rate
to this filter is 2× the chip rate, and the output rate is 4× the
chip rate.
0
0.75
1.25
Table 23. Interpolating HB Filter Fixed Coefficients
Decimal Coefficient
(10-Bit)
14
−66
309
512
–20
INTERPOLATING
HALF-BAND
FILTER RESPONSE
–40
The half-band filters interpolate the incoming data by 2×. For a
channel running at 2× the chip rate, the half-band can be used
to output channel data at 4× the chip rate. The interpolation
operation creates an image of the baseband signal, which is
filtered out by the half-band filter.
–53
–60
–80
–100
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
FREQUENCY AS FRACTION OF INPUT RATE
Figure 54. Interpolating Half-Band Frequency Response
Rev. 0 | Page 47 of 88
05156-043
Normalized
Coefficient
0.02734375
−0.12890625
0.603515625
1
dBc
Coefficient
Number
C1, C11
C3, C9
C5, C7
C6
AD6654
OUTPUT DATA ROUTER
The output data router circuit precedes the six AGCs of the
final output block and immediately follows interpolating halfband filters. This block consists of two subblocks. The first
block is responsible for combining (interleaving) data from
more than one channel into a single stream of data. The second
block performs complex filter completion, as explained later in
this section. The combined data is passed on to the AGCs.
CH0
AGC0
CH1
AGC1
AGC0
The interleaving function is a simple time-multiplexing function, with lower data rate on the input side and higher data rate
on the output side. The output data rate is the sum of all input
stream data rates that are combined.
AGC1
PARALLEL
PORT A
CH2
AGC2
AGC2
STREAM
CONTROL
CH3
The channels that need to be combined are programmable with
sufficient flexibility. Table 24 gives the combinations that are
possible using a 4-bit word (stream control bits) in the Parallel
Port Control 2 register.
PARALLEL
PORT B
AGC3
The same coefficients are programmed into both of the
channels’ RCF filters, and the decimation phases are set to 0
and 1. The decimation phases can be set to 0 for one channel
and 1 for the second channel in the pair. This causes the first
channel to produce the even outputs of the filter, and the
second to produce the odd outputs of the filter. The streams
are then recombined (interleaved) to produce the desired
9.216 MHz output rate. The benefit is that now each channel’s
RCF has time to calculate twice as many taps, because it has a
lower output rate.
AGC3
Table 24. Stream Control Bit Combinations and Selections
AGC4
CH5
AGC5
Stream
Control Bits
0000
AGC4
0001
AGC5
05156-044
CH4
PARALLEL
PORT C
0010
Figure 55. Block Diagram of the Output Data Router
0011
INTERLEAVING DATA
In some cases, filtering using a single channel is insufficient. For
such setups, it is advantageous to combine the filtering
resources of multiple channels rather than using filtering
resources from a single channel.
Multiple channels can be set up to co-process the ADC input
port data with the same NCO and filter setups. The decimation
phase values in one of the RCF filters are set such that the
channel’s filters are exactly out of phase with each other. In the
data router, these multiple channels are interleaved (combined)
to form a single stream of data. Because each individual channel
is decimated more than it would have been if a single channel
were filtering, more number-of-filter taps can be calculated.
This is best illustrated with an example:
0100
0101
0110
0111
1000
1001
Any other
state
Two channels need to work together to produce a filter at an
output rate of 9.216 MHz, when the input rate is 92.16 MHz.
Each channel is decimated by a factor of 20 (total decimation)
to achieve the desired output rate of 4.608 MHz each. This
compares to a decimation of 10, if a single channel were
working towards filtering.
Rev. 0 | Page 48 of 88
Output Streams
Ch 0, Ch 1 combined; Ch 2, Ch 3,
Ch 4, Ch 5 independent
Ch 0, Ch 1, Ch 2 combined; Ch 3,
Ch 4, Ch 5 independent
Ch 0, Ch 1, Ch 2, Ch 3 combined;
Ch 4, Ch 5 independent
Ch 0, Ch 1, Ch 2, Ch 3, Ch 4
combined; Ch 5 independent
Ch 0, Ch 1, Ch 2, Ch 3, Ch 4, Ch 5
combined
Ch 0, Ch 1, Ch 2 combined; Ch 3,
Ch 4, Ch 5 combined
Ch 0, Ch 1 combined; Ch 2, Ch 3
combined; Ch 4, Ch 5 combined
Ch 0, Ch 1 combined; Ch 2, Ch 3
combined; Ch 4, Ch 5 independent
Ch 0, Ch 1, Ch 2 combined; Ch 3,
Ch 4 combined; Ch 5 independent
Ch 0, Ch 1, Ch 2, Ch 3 combined;
Ch 4, Ch 5 combined
Independent channels
Number of
Streams
5
4
3
2
1
2
3
3
3
2
6
AD6654
AUTOMATIC GAIN CONTROL
truncation of bits below the output range. Overflow is caused by
clipping errors when the output signal exceeds the output range.
Modulation error occurs when the output gain varies while
receiving data.
The AD6654 is equipped with six independent automatic gain
control (AGC) loops that directly follow the second data router
and immediately precede the parallel output ports. Each AGC
circuit has 96 dB of range. It is important that the decimating
filters of the AD6654 preceding the AGC reject unwanted
signals, so that each AGC loop is operating only on the carrier
of interest, and carriers at other frequencies do not affect the
ranging of the loop.
The desired signal level should be set based on the probability
density function of the signal, so that the errors due to underflow and overflow are balanced. The gain and damping values
of the loop filter should be set, so that the AGC is fast enough to
track long-term amplitude variations of the signal that might
cause excessive underflow or overflow, but slow enough to
avoid excessive loss of amplitude information due to the
modulation of the signal.
The AGC compresses the 22-bit complex output from the
second data router into a programmable word size of 4 to 8, 10,
12, or 16 bits. Because the small signals from the lower bits are
pushed in to higher bits by adding gain, the clipping of the
lower bits does not compromise the SNR of the signal of
interest.
AGC LOOP
The AGC loop is implemented using a log-linear architecture. It
contains four basic operations: power calculation, error calculation, loop filtering, and gain multiplication.
The AGC maintains a constant mean power on the output
despite the level of the signal of interest, allowing operation in
environments where the dynamic range of the signal exceeds
the dynamic range of the output resolution. The output width of
the AGC is set by writing a 3-bit AGC word-length word in the
AGC control register of the individual channel’s memory map.
The AGC can be configured to operate in either desired signal
level mode or desired clipping level mode. The mode is set by
the AGC clipping error bit of the AGC control register. The
AGC adjusts the gain of the incoming data according to how far
it is from a given desired signal level or desired clipping level,
depending on the selected mode of operation.
The AGC can be bypassed, if needed, and, when bypassed, the
24-bit complex input word remains truncated to a 16-bit value
that is output through the parallel port output. The six AGCs
available on the AD6654 are programmable through the six
channel memory maps. AGCs corresponding to individual
channels can be bypassed by writing Logic 1 to the AGC bypass
bit in the AGC control register.
Two data paths to the AGC loop are provided: one before the
clipping circuitry and one after the clipping circuitry, as shown
in Figure 56. For the desired signal level mode, only the I/Q
path prior to the clipping is used. For the desired clipping level
mode, the difference of the I/Q signals from before and after the
clipping circuitry is used.
Three sources of error can be introduced by the AGC function:
underflow, overflow, and modulation. Underflow is caused by
Q
22
BITS
CLIP
GAIN MULTIPLIER
CLIP
I
PROGRAMMABLE
Q
BIT WIDTH
USED ONLY FOR
DESIRED CLIPPING
LEVEL MODE
MEAN SQUARE (I2 + Q2)
AVERAGE 1 – 16384 SAMPLES
2×
POWER OF 2
DECIMATE 1 – 4096 SAMPLES
SQUARE ROOT
log2(x)
E ERROR
THRESHOLD
Kz –1
G (z) =
1 – (1 + P ) z –1 + Pz –2
ERROR
R DESIRED
K1 GAIN
K2 GAIN
P POLE
Figure 56. Block Diagram of the AGC
Rev. 0 | Page 49 of 88
05156-045
I
AD6654
DESIRED SIGNAL LEVEL MODE
where:
In this mode of operation, the AGC strives to maintain the
output signal at a programmable set level. The desired signal
level mode is selected by writing Logic 0 into the AGC clipping
error enable bit of the AGC control register. The loop finds the
square (or power) of the incoming complex data signal by
squaring I and Q and adding them.
MCIC is the decimation ratio (1 to 4,096).
NAVG is the number of averaged samples programmed as a
multiple of the decimation ratio (1, 2, 3, or 4).
The AGC loop has an average and decimate block. This average
and decimate operation takes place on power samples and
before the square root operation. This block can be programmed to average from 1 to 16,384 power samples, and the
decimate section can be programmed to update the AGC once
every 1 to 4,096 samples. The limitation on the averaging
operation is that the number of averaged power samples should
be a multiple of the decimation value (1×, 2×, 3×, or 4×).
The averaging and decimation effectively means that the AGC
can operate over averaged power of 1 to 16,384 output samples.
Updating the AGC once every 1 to 4,096 samples and operating
on average power facilitates the implementation of the loop
filter with slow time constants, where the AGC error converges
slowly and makes infrequent gain adjustments. It is also useful
when the user wants to keep the gain scaling constant over a
frame of data or a stream of symbols.
Due to the limitation that the number of average samples must
be a multiple of the decimation value, only the multiple
numbers 1, 2, 3, or 4 are programmed. This is set using the
AGC average samples word in the AGC average sample register.
These averaged samples are then decimated with decimation
ratios programmable from 1 to 4,096. This decimation ratio is
defined in the 12-bit AGC update decimation register.
The average and decimate operations are tied together and
implemented using a first-order CIC filter and FIFO registers.
Gain and bit growth are associated with CIC filters and depend
on the decimation ratio. To compensate for the gain associated
with these operations, attenuation scaling is provided before the
CIC filter.
This scaling operation accounts for the division associated with
the averaging operation as well as the traditional bit growth in
CIC filters. Because this scaling is implemented as a bit-shift
operation, only coarse scaling is possible. Fine scaling is implemented as an offset in the request level, as explained later in this
section. The attenuation scaling, SCIC, is programmable from 0
to 14 using a 4-bit CIC scale word in the AGC average samples
register and is given by
[
]
SCIC = ceil log 2 (M CIC × N AVG )
For example, if a decimation ratio MCIC is 1,000 and NAVG is 3
(decimation of 1,000 and averaging of 3,000 samples), then
the actual gain due to averaging and decimation is 3,000 or
69.54 dB (log2 (3000)). Because attenuation is implemented as a
bit-shift operation, only multiples of 6.02 dB attenuations are
possible. SCIC in this case is 12, corresponding to 72.24 dB. This
way, SCIC scaling always attenuates more than is sufficient to
compensate for the gain in the average and decimate sections
and, therefore, prevents overflows in the AGC loop. But it is
also evident that the SCIC scaling induces a gain error (the
difference between gain due to CIC and attenuation provided
by scaling) of up to 6.02 dB. This error should be compensated
for in the request signal level, as explained later in this section.
A logarithm to the Base 2 is applied to the output from the
average and decimate sections. These decimated power samples
are converted to rms signal samples by applying a square root
operation. This square root is implemented using a simple shift
operation in the logarithmic domain. The rms samples obtained
are subtracted from the request signal level R specified in the
AGC desired level register, leaving an error term to be
processed by the loop filter, G(z).
The user sets this programmable Request Signal Level R according to the output signal level that is desired. The Request Signal
Level R is programmable from −0 dB to −23.99 dB in steps of
0.094 dB.
The request signal level should also compensate for errors, if
any, due to the CIC scaling, as previously explained in this
section. Therefore, the request signal level is offset by the
amount of error induced in CIC, given by
Offset = 10 × log(MCIC × NAVG − SCIC × 3.01 dB
where Offset is in dB.
Continuing the previous example, this offset is given by
Offset = 72.24 − 69.54 = 2.7 dB
So the request signal level is given by
⎡ (DSL − Offset )⎤
R = − ceil ⎢
⎥ × 0.094 dBFS
0.094
⎣
⎦
where:
R is the request signal level.
DSL (desired signal level) is the output signal level that the user
desires.
Rev. 0 | Page 50 of 88
AD6654
Therefore, in the previous example, if the desired signal level is
−13.8 dB, the request level R is programmed to be −16.54 dB,
compensating for the offset.
This request signal level is programmed in the 8-bit AGC
desired level register. This register has a floating-point
representation, where the 2 MSBs are exponent bits and the
6 LSBs are mantissa bits. The exponent is in steps of 6.02 dB,
and the mantissa is in steps of 0.094 dB. For example, a value
10’100101 represents 2 × 6.02 + 37 × 0.094 = 15.518 dB.
The AGC provides a programmable second-order loop filter.
The programmable parameters Gain 1 (K1), Gain 2 (K2), Error
Threshold E, and Pole P completely define the loop filter
characteristics. The error term after subtracting the request
signal level is processed by the loop filter, G(z). The open loop
poles of the second-order loop filter are 1 and P, respectively.
The loop filter parameters, Pole P and Gain K, allow the
adjustment of the filter time constant that determines the
window for calculating the peak-to-average ratio.
Depending on the value of the error term that is obtained after
subtracting the request signal level from the actual signal level,
either Gain Value K1 or Gain Value K2 is used. If the error is less
than the programmable threshold E, K1 or K2 is used. This
allows a fast loop when the error term is high (large
convergence steps required), and a slower loop function when
the error term is smaller (almost converged).
The open-loop gain used in the second-order loop G(z) is given
by one of the following equations:
error threshold register, using floating-point representation. It
consists of four exponent bits and eight mantissa bits. Exponent bits
are in steps of 6.02 dB and mantissa bits are in steps of 0.024 dB.
For example, 0111’10001001 represents 7 × 6.02 + 137 × 0.024 =
45.428 dB.
The user defines the open-loop Pole P and Gain K, which also
directly impact the placement of the closed-loop poles and filter
characteristics. These closed-loop poles, P1 and P2, are the roots
of the denominator of the previous closed-loop transfer
function and are given by
P1 , P2 =
(1 + P − K ) ± (1 + P − K )2 − 4 P
2
Typically, the AGC loop performance is defined in terms of its
time constant or settling time. In this case, the closed-loop poles
should be set to meet the time constants required by the AGC
loop.
The relationship between the time constant and the closed-loop
poles that can be used for this purpose is
⎤
⎡
M CIC
P1,2 = exp⎢
⎥
⎢⎣ Sample Rate × τ 1, 2 ⎥⎦
where τ1, 2 are the time constants corresponding to Pole P1 and
Pole P 2.
The time constants can also be derived from settling times as
given by
K = K1, if Error < Error Threshold
τ=
K = K2, if Error > Error Threshold
The open-loop transfer function for the filter, including the gain
parameter, is
G (z) =
Kz −1
1 − (1 + P ) z −1 + Pz − 2
If the AGC is properly configured in terms of offset in the
request level, then there are no gains in the AGC loop except for
K, the filter gain. Under these circumstances, a closed-loop
expression for the AGC loop is given by
GCLOSED (z ) =
G(z )
Kz −1
=
1 + G(z ) 1 + (K − 1 − P )z −1 + Pz −2
Program K1 and K2 (the gain parameters) and Pole P through
AGC loop Gain 1 and Gain 2, and AGC pole location registers
from 0 to 0.996 in steps of 0.0039 using 8-bit representation. For
example, 1000 1001 represent (137/256 = 0.535156). The error
threshold value is programmable between 0 dB and 96.3 dB in
steps of 0.024 dB. This value is programmed in the 12-bit AGC
2% settling time
4
or
5% settling time
3
MCIC (CIC decimation is from 1 to 4,096), and either the settling
time or time constant are chosen by the user. The sample rate is
the sample rate of the stream coming into the AGC. If channels
were interleaved in the output data router, then the combined
sample rate into the AGC should be considered. This rate
should be used in the calculation of poles in the previous
equation, where the sample rate is mentioned.
The loop filter output corresponds to the signal gain that is
updated by the AGC. Because all computation in the loop filter
is done in logarithmic domain (to the Base 2) of the samples,
the signal gain is generated using the exponent (power of 2) of
the loop filter output.
The gain multiplier gives the product of the signal gain with
both the I and Q data entering the AGC section. This signal
gain is applied as a coarse 4-bit scaling and then as a fine scale
8-bit multiplier. Therefore, the applied signal gain is from 0 to
96.3 dB in steps of 0.024 dB. The initial signal gain is programmable using the AGC signal gain register. This register is again a
Rev. 0 | Page 51 of 88
AD6654
4 exponent plus 8 mantissa bit floating-point representation
similar to the error threshold. This is taken as the initial gain
value before the AGC loop starts operating.
The products of the gain multiplier are the AGC scaled outputs
with a 19-bit representation. These are, in turn, used as I and Q
for calculating the power, and the AGC error and loop are
filtered to produce the signal gain for the next set of samples.
These AGC scaled outputs can be programmed to have 4-, 5-,
6-, 7-, 8-, 10-, 12-, or 16-bit widths by using the AGC output
word-length word in the AGC control register. The AGC scaled
outputs are truncated to the required bit widths by using the
clipping circuitry, as shown in Figure 56.
Average Samples Setting
Though it is complicated to express the exact effect of the
number of averaging samples by using equations, intuitively it
has a smoothing effect on the way the AGC loop addresses a
sudden increase or a spike in the signal level. If averaging of
four samples is used, the AGC addresses a sudden increase in
signal level more slowly compared to no averaging. The same
applies to the manner in which the AGC addresses a sudden
decrease in the signal level.
DESIRED CLIPPING LEVEL MODE
Each AGC can be configured so that the loop locks onto a
desired clipping level or a desired signal level. Desired clipping
level mode is selected by writing Logic 1 in the AGC clipping
error mode bit in the AGC control register. For signals that tend
to exceed the bounds of the peak-to-average ratio, the desired
clipping level option provides a way to prevent truncating those
signals and still provide an AGC that attacks quickly and settles
to the desired output level. The signal path for this mode of
operation is shown with dotted lines in Figure 56; the operation
is similar to the desired signal level mode.
First, the data from the gain multiplier is truncated to a lower
resolution (4, 5, 6, 7, 8, 10, 12, or 16 bits) as set by the AGC
output word-length word in the AGC control register. An error
term (for both I and Q) is generated that is the difference
between the signals before and after truncation. This term is
passed to the complex squared magnitude block, for averaging
and decimating the update samples and taking their square root
to find rms samples as in desired signal level mode. In place of
the request desired signal level, a desired clipping level is
subtracted, leaving an error term to be processed by the secondorder loop filter.
The rest of the loop operates the same way as the desired signal
level mode. This way, the truncation error is calculated and the
AGC loop operates to maintain a constant truncation error
level. The only register setting that is different from the desired
signal level mode settings is that the desired clipping level is
stored in the AGC desired level registers instead of in the
request signal level.
AGC SYNCHRONIZATION
When the AGC output is connected to a RAKE receiver, the
RAKE receiver can synchronize the average and update section
to update the average power for AGC error calculation and loop
filtering. This external sync signal synchronizes the AGC
changes to the RAKE receiver and makes sure that the AGC
gain word does not change over a symbol period, which,
therefore, provides a more accurate estimation. This synchronization is accomplished by setting the appropriate bits of the
AGC control register.
Sync Select Alternatives
The AGC can receive a sync as follows:
•
Channel sync: The sync signal is used to synchronize the
NCO of the channel under consideration.
•
Pin sync: Selects one of the four SYNC pins.
•
Sync now bit: Through the AGC control register.
When the channel sync select bit of the AGC control register is
Logic 1, the AGC receives the sync signal used by the NCO of
the corresponding channel for the start. When this bit is Logic 0,
the pin sync defined by the 2-bit SYNC pin select word in the
AGC control register provides the sync to the AGC. Apart from
these two methods, the AGC control register also has a sync
now bit that can be used to provide a sync to the AGC by
writing to this register through the microport or serial port.
SYNC PROCESS
Regardless of how a sync signal is received, the syncing process
is the same. When a sync is received, a start hold-off counter is
loaded with the 16-bit value in the AGC hold-off register, which
initiates the countdown. The countdown is based on the ADC
input clock. When the count reaches 1, a sync is initiated. When
a sync is initiated, the CIC decimation filter dumps the current
value to the square root, error estimation, and loop filter blocks.
After dumping the current value, it starts working toward the
next update value. Additionally on a sync, AGC can be initialized, if the initialize AGC on sync bit is set in the AGC control
register. During initialization, the CIC accumulator is cleared
and new values for CIC decimation, number of averaging
samples, CIC scale, signal gain, open-loop Gain K1 and Gain K2,
and the Pole P parameter are loaded from their respective
registers. When the initialize on sync bit is cleared, these
parameters are not loaded from the registers.
This sync process is also initiated when a channel comes out of
sleep by using the start sync to the NCO. An additional feature
is the first sync only bit in the AGC control register. When this
bit is set, only the first sync initiates the process and the remaining sync signals are ignored. This is useful when syncing using a
pin sync. A sync is required only on the first pulse on this pin.
These additional features make AGC synchronization more
flexible and applicable to varied circumstances
Rev. 0 | Page 52 of 88
AD6654
PARALLEL PORT OUTPUT
The AD6654 incorporates three independent 16-bit parallel
ports for output data transfer. The three parallel output ports
share a common clock, PCLK. Each port consists of a 16-bit
data bus, request signal, acknowledge signal, three channel
indicator pins, one I/Q indicator pin, one gain word indicator
pin, and a common shared PCLK pin. The parallel ports can be
configured to function in master mode or slave mode. By
default, the parallel ports are in slave mode on power-up.
Each parallel port can output data from any or all of the AGCs,
using the 1-bit enable bit for each AGC in the parallel port
control register. Even when the AGC is not required for a
certain channel, the AGC can be bypassed, but the data is still
received from the bypassed AGC. The parallel port
functionality is programmable through the two parallel port
control registers.
Each parallel port can be programmed individually to operate
in either interleaved I/Q mode or parallel I/Q mode. The mode
is selected using a 1-bit data format bit in the parallel port
control register. In both modes, the AGC gain word output can
be enabled using a 1-bit append gain bit in the parallel port
control register for individual output ports. There are six enable
bits per output port, one for each AGC in the corresponding
parallel port.
INTERLEAVED I/Q MODE
Parallel port channel mode is selected by writing a 0 to the data
format bit for the parallel port in consideration. In this mode,
I and Q words from the AGC are output on the same 16-bit data
bus on a time-multiplexed basis. The 16-bit I word is output
followed by the 16-bit Q word. The specific AGCs output by the
port are selected by setting individual bits for each of the AGCs
in the parallel port control register. Figure 57 shows the timing
diagram for the interleaved I/Q mode.
When an output data sample is available for output from an
AGC, the parallel port initiates the transfer by pulling the
PxREQ signal high. In response, the processor receiving the
data needs to pull the PxACK signal high, acknowledging that it
is ready to receive the signal. In Figure 57, PxACK is already
pulled high and, therefore, the 16-bit I data is output on the
data bus on the next PCLK rising edge after PxREQ is driven
logic high. The PxIQ signal also goes high to indicate that I data
is available on the data bus. The next PCLK cycle brings the
Q data onto the data bus. In this cycle, the PxIQ signal is driven
low. When I data and Q data are output, the channel indicator
pins PxCH[2:0] indicate the data source (AGC number).
Figure 57 is the timing diagram for interleaved I/Q mode with
the AGC gain word disabled. Figure 58 is a similar timing
diagram with the AGC gain word. In the PCLK cycle after the Q
data, the AGC gain word is output on the data bus and the
PxGAIN signal is pulled high to indicate that the gain word is
available on the parallel port. Therefore, a minimum of three or
four PCLK cycles are required to output one sample of output
data on the parallel port without or with the AGC gain word,
respectively.
PARALLEL I/Q MODE
In this mode, eight bits of I data and eight bits of Q data are
simultaneously output on the data bus during one PCLK cycle.
The I byte is the most significant byte of the port, while the
Q byte is the least significant byte. The PAIQ and PBIQ output
indicator pins are set high during the PCLK cycle. Note that if
data from multiple AGCs are output consecutively, the PAIQ
and PBIQ output indicator pins remain high until data from all
channels is output. The PACH[2:0] and PBCH[2:0] pins provide
a 3-bit binary value indicating the source (AGC number) of the
data currently being output. Figure 59 is the timing diagram for
parallel I/Q mode.
PCLK
PxACK
tDPREQ
PxREQ
tDPP
Px [15:0]
I [15:0]
Q [15:0]
tDPIC
PxIQ
tDPCH
PxGAIN
PxCH [2:0] = CHANNEL NO.
LOGIC LOW ‘0’
Figure 57. Interleaved I/Q Mode Without an AGC Gain Word
Rev. 0 | Page 53 of 88
05156-046
PxCH [2:0]
AD6654
PCLK
PxACK
tDPREQ
PxREQ
tDPP
Px [15:0]
I[15:0]
Q[15:0]
0000 +
GAIN [11:0]
tDPIQ
PxIQ
tDPCH
PxCH [2:0]
PxCH [2:0] = CHANNEL #
05156-047
tDPGAIN
PxGAIN
Figure 58. Interleaved I/Q Mode with an AGC Gain Word
PCLK
PxACK
tDPREQ
PxREQ
tDPP
I [15:8]
Q [15:8]
Px [15:0]
tDPIQ
PxIQ
tDPCH
PxCH [2:0]
LOGIC LOW 0
PxGAIN
05156-048
PxCH [2:0] =
AGC NO.
Figure 59. Parallel I/Q Mode Without an AGC Gain Word
When an output data sample is available for output from an
AGC, the parallel port initiates the transfer by pulling the
PxREQ signal high. In response, the processor receiving the
data needs to pull the PxACK signal high, acknowledging that it
is ready to receive the signal. In Figure 59, the PxACK is already
pulled high and, therefore, the 8-bit I data and 8-bit Q data are
simultaneously output on the data bus on the next PCLK rising
edge after PxREQ is driven logic high. The PxIQ signal also
goes high to indicate that I/Q data is available on the data bus.
When I/Q data is being output, the channel indicator pins
PxCH[2:0] indicate the data source (AGC number).
Figure 59 is the timing diagram for parallel I/Q mode with the
AGC gain word disabled. Figure 60 is a similar timing diagram
with the AGC gain word enabled. In the PCLK cycle after the
I/Q data, the AGC gain word is output on the data bus, and the
PxGAIN signal is pulled high to indicate that the gain word is
available on the parallel port. During this PCLK cycle, the PxIQ
signal is pulled low to indicate that I/Q data is not available on
the data bus. Therefore, in parallel I/Q mode, a minimum of
two PCLK cycles is required to output one sample of output
data on the parallel port without and with the AGC gain word,
respectively.
The order of data output is dependent on when data arrives at
the port, which is a function of total decimation rate, DRCF/
CRCF decimation phase, and start hold-off values. Priority
order from highest to lowest is, AGC0, AGC1, AGC2, AGC3,
AGC4, and AGC5 for both parallel I/Q and interleaved modes
of output.
Rev. 0 | Page 54 of 88
AD6654
MASTER/SLAVE PCLK MODES
The parallel ports can operate in either master or slave mode.
The mode is set via PCLK master mode bit in the Parallel Port
Control 2 register. The parallel ports power up in slave mode to
avoid possible contentions on the PCLK pin.
In master mode, PCLK is an output derived by dividing
PLL_CLK down by the PCLK divisor. The PCLK divisor can
have a value of 1, 2, 4, or 8, depending on the 2-bit PCLK
divisor word setting in the Parallel Port Control 2 register. The
highest PLCK rate in master mode is 200 MHz. Master mode is
selected by setting the PCLK master mode bit in the Parallel
Port Control 2 register.
PCLK rate =
PLL _ CLK rate
PCLK divisor
In slave mode, external circuitry provides the PCLK signal.
Slave mode PCLK signals can be either synchronous or
asynchronous. The maximum slave mode PCLK frequency is
also 200 MHz.
PCLK
PxACK
tDPREQ
PxREQ
tDPP
Px [15:0]
I [15:8]
Q [15:8]
0000 +
GAIN [11:0]
tDPIQ
PxIQ
tDPCH
PxCH [2:0] = CHANNEL #
tDPGAIN
PxGAIN
Figure 60. Parallel I/Q Mode with an AGC Gain Word
Rev. 0 | Page 55 of 88
05156-049
PxCH [2:0]
AD6654
PARALLEL PORT PIN FUNCTIONS
Table 25 describes the functions of the pins used by the parallel ports.
Table 25. Parallel Port Pin Functions
Pin Name
PCLK
I/O
I/O
PAREQ, PBREQ,
PCREQ
O
PAACK, PBACK,
PCACK
I
PAIQ, PBIQ, PCIQ
PAGAIN, PBGAIN,
PCGAIN
PACH[2:0], PBCH[2:0],
PCCH[2:0]
PADATA[15:0],
PBDATA[15:0],
PCDATA[15:0]
Function
Parallel Clock. PCLK can operate as a master or as a slave. This setting is dependent on the 1-bit PCLK master
mode bit in the Parallel Port Control 2 register. As an output (master mode), the maximum frequency is
CLK/N, where CLK is the AD6654 clock and N is an integer divisor of 1, 2, 4, or 8. As an input (slave mode), it
can be asynchronous or synchronous relative to the AD6654 CLK. This pin powers up as an input to avoid
possible contentions. Parallel port output pins change on the rising edge of PCLK.
Active High Output. Synchronous to PCLK. A logic high on this pin indicates that data is available to be
shifted out of the port. When an acknowledge signal is received, data starts shifting out and this pin remains
high until all pending data has been shifted out.
Active High Asynchronous Input. Applying a logic low on this pin inhibits parallel port data shifting. Applying
a logic high to this pin when REQ is high causes the parallel port to shift out data according to the
programmed data mode. ACK is sampled on the rising edge of PCLK. Assuming that REQ is asserted, the
latency from the assertion of ACK to data appearing at the parallel port output is no more than 1.5 PCLK
cycles. ACK can be continuously held high; in this case, when data becomes available, shifting begins 1 PCLK
cycle after the assertion of REQ (see Figure 57, Figure 58, Figure 59, and Figure 60).
Parallel Output Gain Data Indicators High whenever I data is present on the parallel port data bus; otherwise
low. In parallel I/Q mode, both I data and Q data are available at the same time and, therefore, the PxIQ signal
is pulled high.
Parallel Output Gain Word Indicators. High whenever the AGC gain word is present on the parallel port data
bus; otherwise low.
Channel Indicator Output Ports. These pins identify data in both of the parallel port modes. The 3-bit value
identifies the source of the data (AGC number) on the parallel port when it is being shifted out.
Parallel Output Port Data Bus. Output format is twos complement. In parallel I/Q mode, 8-bit data is present;
in interleaved I/Q mode, 16-bit data is available.
Rev. 0 | Page 56 of 88
AD6654
USER-CONFIGURABLE BUILT-IN SELF-TEST (BIST)
Each channel of AD6654 includes a BIST block. The BIST,
along with an internal test signal (pseudo random test input
signal), can be used to generate a signature. This signature can
be compared with a known good device and an untested device
to see if the untested device is functional.
BIST timer bits in the BIST control register can be programmed
with a timer value that determines the number of clock cycles
that the output of the channels (output of AGC) have
accumulated. When the disable signature generation bit is
written with Logic 0, the BIST timer is counted down and a
signature register is written with the accumulated output of the
AD6654 channel.
When the BIST timer expires, the signature register for I and Q
paths can be read back to compare it with the signature register
from a known good device.
Rev. 0 | Page 57 of 88
AD6654
CHIP SYNCHRONIZATION
The AD6654 offers two types of synchronization: start sync and
hop sync. Start sync is used to bring individual channels out of
sleep after programming. It can also be used while AD6654 is
operational to resynchronize the internal clocks. Hop sync is
used to change or update the NCO frequency tuning word and
the NCO phase offset word.
Two methods can be used to initiate a start sync or hop sync:
•
Soft sync is provided by the memory map registers and is
applied to channels directly through the microport or serial
port interface.
•
Pin sync is provided using four hard-wired SYNC[3:0] pins.
Each channel is programmed to listen to one of these SYNC
pins and do a start sync or a hop sync when a signal is
received on these pins.
repeated, that is, the soft synchronization register needs to be
written twice.
Start with Pin Sync
Four sync pins (SYNC0, SYNC1, SYNC2, and SYNC3) provide
very accurate synchronization among channels. Each channel
can be programmed to monitor any of the four sync pins.
To start the channels with a pin sync:
1.
Write the channel register to enable one more channels, if
the channels are inactive.
2.
Write the NCO start hold-off counter registers with the
appropriate value (greater than 0 and less than 216).
3.
Program the channel NCO control registers to monitor
the appropriate SYNC pins.
The pin synchronization configuration register (Address 0x04)
is used to make pin synchronization even more flexible. The
part can be programmed to be edge-sensitive or level-sensitive
for SYNC pins. In edge-sensitive mode, a rising edge on the
SYNC pins is recognized as a synchronization event.
4.
Write the start synchronization enable bit and SYNC pin
enable bits high in the pin synchronization configuration
register. This starts the countdown of the start hold-off
counter. When the count reaches 1, the channels are
activated or resynchronized.
START
HOP
Start refers to the startup of an individual channel or chip, or of
multiple chips. If a channel is not used, it should be put into
sleep mode to reduce power dissipation. Following a hard reset
(low pulse on the RESET pin), all channels are placed into sleep
mode. Alternatively, channels can be manually put to sleep by
writing 0 to the sleep register.
Hop is a jump from one NCO frequency and/or phase offset to
a new NCO frequency and/or phase offset. This change in
frequency and/or phase offset can be synchronized via microprocessor control (soft sync) or via an external sync signal
(pin sync).
Start with Soft Sync
The AD6654 can synchronize channels or chips under microprocessor control. The start hold-off counter, in conjunction
with the soft start enable bit and the channel enable bits, enables
this synchronization.
The AD6654 can synchronize a change in NCO frequency
and/or phase offset of multiple channels or chips under
microprocessor control. The NCO hop hold-off counter, in
conjunction with the soft hop enable bit and the channel enable
bits, enables this synchronization.
To synchronize the start of multiple channels via microprocessor control:
To synchronize the hop of multiple channels via microprocessor
control:
1.
Write the channel enable register to enable one or more
channels, if the channels are inactive.
1.
Write the NCO frequency register(s) or phase offset
register(s) to the new value.
2.
Write the NCO start hold-off counter registers with the
appropriate value (greater than 0 and less than 216).
2.
Write the NCO frequency hold-off counter registers with
the appropriate value (greater than 0 and less than 216).
3.
Write the soft sync channel enable bit(s) and soft start
synchronization enable bit high in the soft synchronization configuration register. This starts the countdown by
the start hold-off counter. When the count reaches 1, the
channels are activated or resynchronized.
3.
Write 0x00 to the soft synchronization configuration
register.
4.
Write the soft hop synchronization enable bit and the
corresponding soft sync channel enable bits high in the
soft synchronization configuration register. This starts the
countdown by the frequency hold-off counter. When the
Hop with Soft Sync
Note: When using SPI or SPORT for programming these
registers, the last step in the above procedure needs to be
Rev. 0 | Page 58 of 88
AD6654
count reaches 1, the new frequency and/or phase offset is
loaded into the NCO.
To control the hop of channel NCO frequencies:
1.
Write the NCO frequency register(s) or phase offset
register(s) to the new value.
2.
Write the NCO frequency hold-off counter(s) to the
appropriate value (greater than 0 and less than 216).
Hop with Pin Sync
3.
Four sync pins (SYNC0, SYNC1, SYNC2, and SYNC3) provide
very accurate synchronization among channels. Each channel
can be programmed to look at any of the four sync pins.
Program the channel NCO control registers to monitor
the appropriate SYNC pins.
4.
Write the hop synchronization enable bit and SYNC pin
enable bits high in the pin synchronization configuration
register. This enables the countdown of the frequency
hold-off counter. When the count reaches 1, the new
frequency and/or phase offset is loaded into the NCO.
Note: When using SPI or SPORT for programming these
registers, the last step in the above procedure needs to be
repeated, that is, the soft synchronization register needs to be
written twice.
Rev. 0 | Page 59 of 88
AD6654
SERIAL PORT CONTROL
The AD6654 serial port allows all memory to be accessed
(programmed or readback) serially in one-byte words. Either
serial port or microport can be used (but not both) at any given
time. Serial port control is selected using the SMODE pin (0 =
microport, 1 = serial port). Two serial port modes are available.
An SPI-compatible port is provided as well as a SPORT. The
choice of SPI or SPORT mode is selected using the MODE pin
(0 = SPI, 1 = SPORT).
Each individual byte of serial data (address, instruction and
data) may be shifted in either MSB first or LSB first using the
MSBFIRST pin (1 = MSB first, 0 = LSB first). The serial chip
select (SCS) pin is brought low to access the device for serial
control. When the SCS pin is held high, serial programming is
inhibited.
HARDWARE INTERFACE
The pins described in Table 26 comprise the physical interface
between the user’s programming device and the serial port of
the AD6654. All serial pins are inputs except for SDO, which is
an open-drain output and should be pulled high by an external
pull-up resistor (suggested value 1 kΩ).
A complete read or write cycle requires a minimum of three
bytes to transfer, consisting of address word, instruction word,
and data-word(s). As many as 127 data-words can be
transferred during a block transfer cycle. All address,
instruction, and data-word(s) must be formatted LSB first or
MSB first to match the state of the MSBFIRST pin.
The first word for serial transfer is the internal register address.
In LSB first mode, the address is the lower-most address for the
block transfer (subsequent addresses are generated by internal
increment). In MSB first, the address is highest address for the
block transfer (subsequent addresses are generated by internal
decrement).
The second word of serial transfer contains a one-bit read/write
indicator (1 = read, 0 = write), and seven bits to define the
number of data bytes to be transferred (N). For a single data
byte transfer (N = 1); one byte is shifted into SDI for a write
transfer, or shifted out of SDO for a read transfer, and the cycle
is complete. For a block transfer, N write/read operations are
performed, and the internal register address increments
(MSBFIRST = 0) or decrements (MSBFIRST = 1) after each
data byte is clocked into SDI for a write operation, or after each
data byte is clocked out of SDO for a read operation.
Figure 61 to Figure 64 illustrate a three byte block transfer
through the serial port. Read and write operations with
MSBFIRST high and low are shown. Please note that the figures
show the sequence for write/read transfer, and actual data
should be shifted in or out based upon the status of the
MSBFIRST pin. The operation details are common to both SPI
and SPORT modes except for the use of framing signals and
timing. Individual mode details follow. In single byte transfer
mode, the count in the second byte would be reduced to one,
and the number of data bytes would be reduced to one.
Table 26. Serial Port Pins
Pin
SCLK
MSBFIRST
STFS
SRFS
SDI
SDO
SCS
SMODE
MODE
Function
Serial Clock in Both SPI and SPORT Modes. Should have a rise/fall time of 3 ns max.
Indicates whether the first bit shifted in or out of the serial port is the MSB (1) or LSB (0) for both instruction and datawords. Also indicates if the first instruction word (address) is a block start or a block end for multiple byte transfers. This
pin also controls the functionality when programming indirectly addressed registers.
Serial Transmit Frame Sync in SPORT Mode. STFS is not used in SPI mode.
Serial Receive Frame Sync in SPORT Mode. SRFS is not used in SPI mode.
Serial Data Input in Both Modes. Serial data is clocked in on the rising edge of SCLK.
Serial Data Output in Both Modes. Serial data is clocked out on the rising edge of SCLK.
Active-Low Serial Chip Select in Both Modes.
Serial Mode. Part is programmed through the serial port when this pin is high.
Mode Pin. Selects between SPI (0) and SPORT (1) modes.
Rev. 0 | Page 60 of 88
AD6654
MSBFIRST
SCS
BLOCK END ADDRESS WR + COUNT (3)
SDI
0xaa
0x03
DATA TO BLOCK END
ADDRESS
DATA TO BLOCK END
ADDRESS – 1
DATA TO BLOCK END
ADDRESS – 2
aa
aa – 1
aa – 2
05156-075
SDO
MODE
Figure 61. Serial Write of Three Bytes with MSBFIRST = 1 (All Words are Written MSB first)
MSBFIRST
SCS
SDI
BLOCK START
ADDRESS
WR + COUNT (3)
0xaa
0x03
DATA TO BLOCK START DATA TO BLOCK START DATA TO BLOCK START
ADDRESS
ADDRESS + 1
ADDRESS + 2
aa
aa + 1
aa + 2
05156-076
SDO
MODE
Figure 62. Serial Write of Three Bytes with MSBFIRST = 0 (All Words are Written LSB First)
MSBFIRST
SCS
SDI
BLOCK END
ADDRESS
RD + COUNT (3)
0xaa
0x83
DATA FROM BLOCK END
ADDRESS
aa
DATA FROM BLOCK END
ADDRESS – 2
aa – 1
aa – 2
05156-077
SDO
DATA FROM BLOCK END
ADDRESS – 1
MODE
Figure 63. Serial Read of Three Bytes with MSBFIRST = 1 (All Words are Written or Read MSB First)
Rev. 0 | Page 61 of 88
AD6654
MSBFIRST
SCS
BLOCK START
ADDRESS
RD + COUNT (3)
0xaa
0x83
SDI
DATA FROM BLOCK START
ADDRESS
DATA FROM BLOCK START
ADDRESS + 1
DATA FROM BLOCK START
ADDRESS + 2
aa + 1
aa + 2
aa
05156-078
SDO
MODE
Figure 64. Serial Read of Three Bytes with MSBFIRST = 0 (All Words are Written or Read LSB First)
SPI MODE TIMING
SPI Write
In SPI mode, the SCLK should run only when data is being
transferred and SCS is logic low. If SCLK runs when SCS is logic
high, the internal shift register continues to run and instruction
words or data are lost. No external framing is necessary. The
SCS pin can be pulled low once for each byte of transfer, or kept
low for the whole length of the transfer.
Data on the SDI pin is registered on the rising edge of SCLK.
During a write, the serial port accumulates eight input bits
of data before transferring one byte to the internal registers.
Figure 65 and Figure 66 show one byte block transfer for
writing in MSBFIRST and LSBFIRST modes.
MSBFIRST
SCLK
SCS
SMODE
BLOCK END ADDRESS
SDI
A7
A6
A5
A4
A3
A2
A1
WRITE
A0
0
BLOCK COUNT (Nx)
N6
N5
N4
N3
N2
N1
N0
D7
D6
D5
D4
D3
D2
D1
D0
05156-079
SDO
MODE
Figure 65. SPI Write MSBFIRST = 1
Rev. 0 | Page 62 of 88
AD6654
MSBFIRST
SCLK
SCS
SMODE
BLOCK END ADDRESS
SDI
A0
A1
A2
A3
A4
A5
A6
BLOCK COUNT (Nx)
A7
N0
N1
N2
N3
N4
WRITE
N5
N6
0
D0
D1
D2
D3
D4
D5
D6
D7
05156-058
SDO
MODE
Figure 66. SPI Write MSBFIRST = 0
SPI Read
Register readback data shifts out on the rising edge of SCLK.
The SDO pin is in a high impedance state at all times except
during a read cycle.
During a typical read operation, a one byte address and one
byte instruction are written to the serial port to instruct the
internal control logic as to which registers are to be accessed.
MSBFIRST
SCLK
SCS
SMODE
BLOCK END ADDRESS
SDI
A7
A6
A5
A4
A3
A2
A1
READ
A0
1
BLOCK COUNT (Nx)
N6
N5
N4
N3
N2
N1
N0
D7
D6
D5
D4
D3
D2
D1
D0
05156-080
SDO
MODE
Figure 67. SPI Read MSBFIRST = 1
Rev. 0 | Page 63 of 88
AD6654
MSBFIRST
SCLK
SCS
SMODE
BLOCK START ADDRESS
SDI
A0
A1
A2
A3
A4
A5
A6
BLOCK COUNT (Nx)
A7
N0
N1
N2
N3
N4
READ
N5
N6
1
SDO
D1
D2
D3
D4
D5
D6
D7
05156-059
D0
MODE
Figure 68. SPI Read MSBFIRST = 0
SPORT MODE TIMING
SPORT Write
In SPORT mode, the SCLK continuously runs, and the external
SRFS and STFS signals are used to frame the data. Incoming
framing signals SRFS (receive) and STFS (transmit) are sampled
on the falling edges of SCLK. All input and output data must be
transmitted or received in 8-bit segments starting with the
rising edge after SRFS or STFS is sampled.
Serial data is sampled on the rising edge of SCLK. The data
should be MSB or LSB first, depending on the polarity of the
MSBFIRST pin. The serial port begins to sample data on the
rising edge of SCLK after SRFS is detected on the falling edge of
SCLK. Once all 8-bits of one byte are shifted in, the data is
transferred to the internal bus.
MSBFIRST
SCLK
SCS
SMODE
SRFS
BLOCK START ADDRESS
SDI
A7
A6
A5
A4
A3
A2
A1
WRITE
A0
0
BLOCK COUNT (Nx)
N6
N5
N4
N3
N2
N1
N0
D7
D6
D5
D4
D3
D2
D1
D0
STFS
05156-081
SDO
MODE
Figure 69. SPORT Write MSBFIRST = 1
Rev. 0 | Page 64 of 88
AD6654
MSBFIRST
SCLK
SCS
SMODE
SRFS
BLOCK START ADDRESS
SDI
A0
A1
A2
A3
A4
A5
A6
BLOCK COUNT (Nx)
A7
N0
N1
N2
N3
N4
WRITE
N5
N6
0
D0
D1
D2
D3
D4
D5
D6
D7
STFS
05156-060
SDO
MODE
Figure 70. SPORT Write MSBFIRST = 0
readback. STFS must be asserted for every 8-bit readback and is
sampled on the falling edge of SCLK. Data is shifted out on the
rising edge of SCLK. The SDO pin is in a high impedance state
at all times except during a read operation.
SPORT Read
For a typical SPORT read operation, the user must write an
address byte and instruction byte to the serial port to instruct
the internal control logic as to which registers are to be
MSBFIRST
SCLK
SCS
SMODE
SRFS
BLOCK START ADDRESS
SDI
A7
A6
A5
A4
A3
A2
A1
READ
A0
1
BLOCK COUNT (Nx)
N6
N5
N4
N3
N2
N1
N0
STFS
D7
D6
D5
D4
D3
D2
D1
D0
05156-082
SDO
MODE
Figure 71. SPORT Read MSBFIRST = 1
Rev. 0 | Page 65 of 88
AD6654
MSBFIRST
SCLK
SCS
SMODE
SRFS
BLOCK START ADDRESS
SDI
A0
A1
A2
A3
A4
A5
A6
BLOCK COUNT (Nx)
A7
N0
N1
N2
N3
N4
N5
READ
N6
1
STFS
SDO
D1
D2
D3
D4
D5
D6
D7
05156-061
D0
MODE
Figure 72. SPORT Read MSBFIRST = 0
Rev. 0 | Page 66 of 88
AD6654
PROGRAMMING INDIRECT ADDRESSED REGISTERS
USING SERIAL PORT
This section gives examples for programming CRCF coefficient
RAM (with an indirect addressing scheme) using the serial port
(either SPI or SPORT modes). Though the following specific
examples are for CRCF coefficient RAM programming, they can
be extended to other indirect addressed registers like DRCF
coefficient RAM. There are four possible programming scenarios,
and examples are given for all scenarios using two commands:
SerialWrite(data) and SerialRead. These commands signify an 8bit write to, or an 8-bit read from, the serial port (SPI or SPORT).
SerialWrite(8-bit number): is an 8-bit write to SPI or SPORT. In
SPI mode, the SCLK is toggled eight times while SCS is pulled low.
In SPORT mode, SCS is pulled low, SRFS is held high for one
SCLK cycle, and eight bits of data are shifted into the SDI pin
following the SRFS pulse. Though the 8-bit number argument
shown in the following code is always shown MSBFIRST, it is
written with MSB shifting into the device first in MSBFIRST
mode, and it is written with LSB shifting into the device first in
LSBFIRST mode.
SerialRead(): is an 8-bit read from the SDO pin in SPI or SPORT
modes. In SPI mode, the SCLK toggles eight times while SCS is
low. In SPORT mode, SCS is pulled low, STFS is held high for one
SCLK cycle, and then the eight bits of data that shifted out on
SDO following the STFS pulse are read. The data shifted out
should be interpreted based on the polarity of the MSBFIRST pin.
MSBFIRST Mode Using Single Byte Block Transfers
SerialWrite(0x98); //CRCF Start Address
SerialWrite(0x01);
SerialWrite(0x00);
SerialWrite(0x99); //CRCF Final Address
SerialWrite(0x01);
SerialWrite(N-1); //N is the number of coefficients
for (i=0 ; i < N; i++) {
//writing registers
SerialWrite(0x9E);
//MSB written first
SerialWrite(0x01);
//data bits[23:16]
SerialWrite(coeff[i] >> 16 & 0xFF);
SerialWrite(0x9D);
SerialWrite(0x01);
//data bits[15:8]
SerialWrite(coeff[i] >> 8 & 0xFF);
SerialWrite(0x9C);
//LSB written last
SerialWrite(0x01);
//data bits[7:0]
SerialWrite(coeff[i] & 0xFF);
}
SerialWrite(0x98); //CRCF Start Address
SerialWrite(0x01);
SerialWrite(0x00);
SerialWrite(0x99); //CRCF Final Address
SerialWrite(0x01);
SerialWrite(N-1); //N is the number of coefficients
for (i=0 ; i < N; i++) {
//reading registers
SerialWrite(0x9E);
//MSB readback first
SerialWrite(0x81);
//data bits[23:16]
Coeff[i] = SerialRead() << 16;
SerialWrite(0x9D);
SerialWrite(0x81);
//data bits[15:8]
Coeff[i] |= SerialRead() << 8;
SerialWrite(0x9C);
//LSB readback last
SerialWrite(0x81);
//data bits[7:0]
Coeff[i] |= SerialRead();
}
Rev. 0 | Page 67 of 88
AD6654
LSBFIRST Mode Using Single Byte Block Transfers
MSBFIRST Mode Using Multi Byte Block Transfers
SerialWrite(0x98); //CRCF Start Address
SerialWrite(0x01);
SerialWrite(0x00);
SerialWrite(0x99); //CRCF Final Address
SerialWrite(0x02);
SerialWrite(N-1); //N is the number of coefficients
SerialWrite(0x00);
SerialWrite(0x99); //CRCF Final Address
SerialWrite(0x01);
SerialWrite(N-1); //N is the number of coefficients
for (i=0 ; i < N; i++) {
for (i=0 ; i < N; i++) {
//writing registers
SerialWrite(0x9E);
SerialWrite(0x03);
//data bits[23:16]
SerialWrite(coeff[i] >> 16 & 0xFF);
//data bits[15:8]
SerialWrite(coeff[i] >> 8 & 0xFF);
//data bits[7:0]
SerialWrite(coeff[i] & 0xFF);
// writing registers
SerialWrite(0x9C);
//LSB written first
SerialWrite(0x01);
//data bits[7:0]
SerialWrite(coeff[i] & 0xFF);
SerialWrite(0x9D);
SerialWrite(0x01);
//data bits[15:8]
SerialWrite(coeff[i] >> 8 & 0xFF);
}
SerialWrite(0x9E);
//MSB written last
SerialWrite(0x01);
//data bits[23:16]
SerialWrite(coeff[i] >> 16 & 0xFF);
SerialWrite(0x99); //CRCF Final Address
SerialWrite(0x02);
SerialWrite(N-1); //N is the number of coefficients
SerialWrite(0x00);
}
for (i=0 ; i < N; i++) {
SerialWrite(0x98); //CRCF Start Address
SerialWrite(0x01);
SerialWrite(0x00);
SerialWrite(0x9E);
SerialWrite(0x83);
//data bits[23:16]
Coeff[i] = SerialRead() << 16;
//data bits[15:8]
Coeff[i] |= SerialRead() << 8;
//data bits[7:0]
Coeff[i] |= SerialRead();
SerialWrite(0x99); //CRCF Final Address
SerialWrite(0x01);
SerialWrite(N-1); //N is the number of coefficients
for (i=0 ; i < N; i++) {
SerialWrite(0x9C);
SerialWrite(0x81);
//data bits[7:0]
Coeff[i] = SerialRead();
//reading registers
//reading registers
//LSB readback first
}
LSBFIRST Mode Using Multi Byte Block Transfers
SerialWrite(0x98); //CRCF Start Address
SerialWrite(0x02);
SerialWrite(0x00);
SerialWrite(N-1); //N is the number of coefficients
SerialWrite(0x9D);
SerialWrite(0x81);
//data bits[15:8]
Coeff[i] |= SerialRead() << 8;
for (i=0 ; i < N; i++) {
SerialWrite(0x9E);
//MSB readback last
SerialWrite(0x81);
//data bits[23:16]
Coeff[i] |= SerialRead() << 16;
//writing registers
SerialWrite(0x9C);
SerialWrite(0x03);
//data bits[7:0]
SerialWrite(coeff[i] & 0xFF);
//data bits[15:8]
SerialWrite(coeff[i] >> 8 & 0xFF);
//data bits[23:16]
SerialWrite(coeff[i] >> 16 & 0xFF);
}
}
SerialWrite(0x98); //CRCF Start Address
SerialWrite(0x02);
SerialWrite(0x00);
SerialWrite(N-1); //N is the number of coefficients
for (i=0 ; i < N; i++) {
//reading registers
SerialWrite(0x9C);
SerialWrite(0x83);
//data bits[7:0]
Coeff[i] = SerialRead();
//data bits[15:8]
Coeff[i] |= SerialRead() << 8;
//data bits[23:16]
Coeff[i] |= SerialRead() << 16;
}
Rev. 0 | Page 68 of 88
AD6654
In SPORT mode, the Blackfin provides the SCLK, SRFS, and
STFS signals, as shown in Figure 74.
In SPI mode, the Blackfin DSP must act as a master to the
AD6654 by providing the SCLK. SDO is an open-drain output,
so that multiple slave devices can be connected together.
Figure 73 shows a typical connection.
(MASTER)
SCLK
SPISS
SRFS
AND
STFS
MOSI
MISO
VDDIO
SDO
SCS
PF2
PROGRAMMABLE FLAG
MODE
SCLK
TFS
SRFS
RFS
STFS
DT
DR
VDDIO
SDI
SDO
SCS
PF2
PROGRAMMABLE FLAG
MODE
SDI
GND
AD6654
SMODE
GND
AD6654
Figure 74. SPORT Mode Serial Port Connections to Blackfin
(SLAVE)
SMODE
05156-054
BLACKFIN
SCK
BLACKFIN
SCK
Figure 73. SPI Mode Serial Port Connection to Blackfin DSP
Rev. 0 | Page 69 of 88
05156-055
CONNECTING THE AD6654 SERIAL PORT TO A
BLACKFIN DSP
AD6654
MICROPORT
The microport on the AD6654 can be used for programming
the part, reading register values, and reading output data (I, Q,
and RSSI words).
Note that, at any given point in time, either the microport or the
serial port can be active, but not both. Some of the balls on the
package are shared between the microport and the serial port
and have dual functionality based on the SMODE pin. The
microport is selected by pulling the SMODE pin low (ground).
Both read and write operations can be performed using the
microport. The direct addressing scheme is used and any
internal register can be accessed using an 8-bit address. The
data bus can be either 8-bit or 16-bit as set by the chip I/O
access control register. Microport operation is synchronous to
CPUCLK, which must be supplied external to the AD6654 part.
CPUCLK should be less than CLK and 100 MHz.
The microport can operate in Intel mode (separate read and
write strobes) or in Motorola mode (single read/write strobe).
The MODE pin is used to select between Intel (INM, MODE =
0) and Motorola (MNM, MODE = 1) modes. Some AD6654
pins have dual functionality based on the MODE pin. Table 27
lists the pin functions for both modes.
Table 27. Microport Programming Pins
Pin Name
RESET
SMODE
MODE
A[7:0]
D[15:0]
R/W (WR)
DS (RD)
DTACK (RDY)
CS
Intel Mode
RESET
Logic 0
Logic 0
A[7:0]
D[15:0]
WR
RD
RDY
CS
Motorola Mode
RESET
Logic 0
Logic 1
A[7:0]
D[15:0]
R/W
DS
DTACK
CS
INTEL (INM) MODE
The programming port performs synchronous Intel-style reads
and writes on the positive edge of the CPUCLK input when
RESET is inactive (active low signal). The CPUCLK pin is
driven by the programming device (CPUCLK of DSP or
FPGA). During a write access, the A[7:0] address bus provides
the address for access, and the D[15:0] bus (D[7:0] if the 8-bit
data bus is used) is driven by the programming device. The data
bus is driven by the AD6654 during a read operation. Intel
mode uses separate read (RD) and write (WR) active low data
strobes to indicate both the type of access and the valid data for
that access.
The chip select (CS) is an active-low input that signals when an
access is active on its programming port pins. During an access,
the AD6654 drives RDY low to indicate that it is performing the
access. When the internal read or write access is complete, the
RDY pin is pulled high. Because the RDY pin is an open-drain
output with a weak internal pull-up resistor (70 kΩ), an
external pull-up resistor is recommended (see the DDC Design
Notes section). Figure 10 and Figure 11 are the timing diagrams
for read and write cycles using the microport in INM mode.
For an asynchronous write operation in Intel (INM) mode, the
CPUCLK should be running. Set up the data and address buses.
Pull the WR signal low and then pull the CS signal low. The
RDY goes low to indicate that the access is taking place internally. When RDY goes high, the write cycle is complete and CS
can be pulled high to disable the microport.
For an asynchronous read operation on the Intel mode microport, set up the address bus and three-state the data bus. Pull
the RD signal low and then pull the CS signal low. The RDY
goes low to indicate an internal access. When RDY goes low,
valid data is available on the data bus for read.
MOTOROLA (MNM) MODE
The programming port performs synchronous Motorola-style
reads and writes on the positive edge of CPUCLK when RESET
is inactive (active low signal). The A[7:0] bus provides the
address to access and the D[15:0] bus (D[7:0], if the 8-bit data
bus is used) is externally driven with data during a write (driven
by the AD6654 during a read). Motorola mode uses the R/W
line to indicate the type of access (Logic 1 = read, Logic 0 =
write), and the active low data strobe (DS) signal is used to
indicate valid data.
The chip select (CS) is an active-low input that signals when an
access is active on its programming port pins. When the read/
write cycle is complete, the AD6654 drives DTACK low. The
DTACK signal goes high again after either the CS or DS signal
is driven high. Because the DTACK pin is an open-drain output
with a weak internal pull-up resistor (70 kΩ), an external pullup resistor is recommended (see the DDC Design Notes
section). Figure 12 and Figure 13 are the timing diagrams for
read and write cycles using the microport in MNM mode.
For an asynchronous write operation on the Motorola mode
microport, the CPUCLK should be running. Set up the data and
address buses. Pull the R/W and DS signals low and then pull
the CS signal low. The DTACK goes low after a few clock cycles
to indicate that the write access is complete and that CS can be
pulled high to disable the microport. For an asynchronous read
operation on the Motorola mode microport, set up the address
bus and three-state the data bus. Pull the RD signal low and
then pull the CS signal low. The DTACK goes low after a few
clock cycles to indicate that valid data is on the data bus.
Rev. 0 | Page 70 of 88
AD6654
ACCESSING MULTIPLE AD6654 DEVICES
If multiple AD6654 devices are on a single board, the microport
pins for these devices can be shared. In this configuration, a
single programming device (DSP, FPGA, or microcontroller)
can program all AD6654 devices connected to it.
Each AD6654 has four CHIPID pins that can be connected in
16 different ways. During a write/read access, the internal
circuitry checks to see if the CHIPID bits in the chip I/O access
control register (Address 0x02) are the same as the logic levels
of the CHIPID pins (hardwired to the part). If the CHIPID bits
and the CHIPID pins have the same value, then a write/read
access is completed; otherwise, the access is ignored.
To program multiple devices using the same microport control
and data buses, the devices should have separate CHIPID pin
configurations. A write/read access can be made only on the
intended chip; all other chips would ignore the access.
Rev. 0 | Page 71 of 88
AD6654
MEMORY MAP
READING THE MEMORY MAP TABLE
OPEN LOCATIONS
Each row in the memory map table has four address locations.
The memory map is roughly divided into four regions: global
register map (Address 0x00 to Address 0x0B), input port
register map (Address 0x0C to Address 0x67), channel register
map (Address 0x68 to Address 0xBB), and output port register
map (Address 0xBC to Address 0xE7). The channel register
map is shared by all six channels, and access to individual
channels is given by the channel I/O access control register
(Address 0x02).
All locations marked as open are currently not used. When
required, these locations should be written with 0s. Writing to
these locations is required only when part of an address location
is open (for example, Address 0x78). If the whole address
location is open (for example, Address 0x00), then this address
location does not need to be written. If the open locations are
read back using the microport or serial port, the readback value
is undefined (each bit can be independently 1 or 0), and these
bits have no significance.
In the memory map in Table 28, the addresses are given in the
right column. The column with the heading Byte 0 has the
address given in the right column. The column Byte 1 has the
address given by 1 more than the address listed in the right
column (address offset of 1). Similarly, the address offset for the
Byte 2 column is 2, and for the Byte 3 column is 3. For example,
the second row lists 0x04 as the address in the right column.
The pin synchronization configuration register has Address
0x04, the soft synchronization configuration register has
Address 0x05, and Address 0x06 and Address 0x07 are
reserved/open.
If an address location has more than one register or has one
register with some open bits, then the order of these registers is
as given in Table 28. For example, Address 0x33 reads
BIT FORMAT
Here, Bits <7:2> of Address 0x35 are open <15:10>. Bits <1:0>
of Address 0x35 and Bits <7:0> of Address 0x34 make up the
Port A upper threshold <9:0> register (Bit 1 of Address 0x35 is
the MSB of the Port A upper threshold register).
All registers are in little-endian format. For example, if a register
takes 24 bits or three address locations, then the most significant byte is at the highest address location and the least
significant byte is at a lowest address location. In all registers,
the least significant bit is Bit 0 and the most significant bit is
Bit 7. For example, the NCO frequency <31:0> register is
32 bits wide. Bit 0 (LSB) of this register is written at Bit 0 of
Address 0x70 and Bit 32 (MSB) of this register is written at
Bit 7 of Address 0x73.
When referring to a register that takes up multiple address
locations, it is referred to by the address location of the most
significant byte of the register. For example, the text reads,
“Port A dwell timer at Address 0x2A.” Note that only the four
most significant bits of this register are at this location, and this
register also takes up Addresses 0x29 and 0x28.
Open <7:5>, Port A Signal Monitor <4:0>.
The open <7:5> is located at Bits <7:5> and the Port A signal
monitor <4:0> is located at Bits <4:0>.
Another example is Address 0x35:
Open <15:10>, Port A Upper Threshold <9:0>
DEFAULT VALUES
Coming out of reset, some of the address locations (but not all)
are loaded with default values. When available, the default
values for the registers are given in the table. If the default value
is not listed, then the address location is in an undefined state
(Logic 0 or Logic 1) on RESET.
LOGIC LEVELS
In the explanation of various registers, “bit is set” is
synonymous with “bit is set to Logic 1” or “writing Logic 1 for
the bit.” Similarly “clear a bit” is synonymous with “bit is set to
Logic 0” or “writing Logic 0 for the bit.”
Rev. 0 | Page 72 of 88
AD6654
Table 28. Memory Map
8-Bit Hex
Address
0x03
0x07
Byte 3
Byte 2
Open <7:6>, Channel
Open <7:6>, Channel I/O
Enable <5:0>
Access Control <5:0>
Open <15:11>, Reserved <10:0> (default 0x06FC)
Byte 1
Byte 0
Chip I/O Access Control
Open <7:0>
<7:0> (default 0x00)
Soft Synchronization
Pin Synchronization
Configuration <7:0>
Configuration <7:0>
Interrupt Status <15:0> (read only, default 0x00)
0x0B
Interrupt Mask <15:0>
ADC Input Port Register Map— Addresses 0x0C to 0x57
0x0F
ADC Input Control <31:0>
0x13
Open <15:0>
ADC CLK Control <15:0> (default 0x0000)
0x4B
ADC Gain Control <7:0>
Open <23:20>, ADC Dwell Timer <19:0>
0x4F
Open <7:0>
ADC Power Monitor Period <23:0>
0x53
Open <7:5>, ADC Signal
ADC Power Monitor Output <23:0>
Monitor <4:0>
0x57
Open <15:10>, ADC Lower Threshold <9:0>
Open <15:10>, ADC Upper Threshold <9:0>
Channel Register Map—Addresses 0x68 to 0xBB
0x6B
Open <15:0>
Open <15:9>, NCO Control <8:0>
0x6F
NCO Start Hold-Off Counter <15:0>
NCO Frequency Hold-Off Counter <15:0>
0x73
NCO Frequency <31:0> (default 0x0000 0000)
0x77
Open <15:0>
NCO Phase Offset <15:0> (default 0x0000)
0x7B
Open <7:1>, CIC Bypass <0>
Open <7:5>, CIC
Open <7:5>, CIC Scale
Open <7:4>, FIR-HB
Decimation <4:0>
Factor <4:0>
Control <3:0>
0x7F
Open <15:0>
Open <15:13>, MRCF Control <12:0>
0x83
Open <7:6>, MRCF
Open <7:6>, MRCF
Open <7:6>, MRCF
Open <7:6>, MRCF
Coefficient 3 <5:0>
Coefficient 2 <5:0>
Coefficient 1 <5:0>
Coefficient 0 <5:0>
0x87
Open <7:6>, MRCF
Open <7:6>, MRCF
Open <7:6>, MRCF
Open <7:6>, MRCF
Coefficient 7 <5:0>
Coefficient 6 <5:0>
Coefficient 5 <5:0>
Coefficient 4 <5:0>
0x8B
Open <15:13>, DRCF Control Register <12:0>
Open <7:6>, DRCF
Open <7>, DRCF Taps
Coefficient Offset <5:0>
<6:0>
0x8F
Open <15:0>
Open <7:6>, DRCF Final
Open <7:6>, DRCF Start
Address <5:0>
Address <5:0>
0x93
Open<15:0>
Open<15:14>, DRCF Coefficient Memory <13:0>
0x97
Open <15:13>, CRCF Control Register <12:0>
Open <7:6>, CRCF
Open <7>, CRCF Taps
Coefficient Offset <5:0>
<6:0>
0x9B
Open <15:0>
Open <7:6>, CRCF Final
Open <7:6>, CRCF Start
Address <5:0>
Address <5:0>
0x9F
Open <7:0>
Open <23:20>, CRCF Coefficient Memory <19:0>
0xA3
Open <15:11>, AGC Control Register <10:0>
AGC Hold-Off Register <15:0>
0xA7
Open <15:12>, AGC Update Decimation <11:0>
Open <15:12>, AGC Signal Gain <11:0>
0xAB
Open <15:12>, AGC Error Threshold <11:0>
Open <7:6>, AGC Average AGC Pole Location <7:0>
Samples <5:0>
0xAF
Open <7:0>
AGC Desired Level <7:0>
AGC Loop Gain2 <7:0>
AGC Loop Gain1 <7:0>
0xB3
Open <7:0>
BIST I Path Signature Register <23:0> (read only)
0xB7
Open <7:0>
BIST Q Path Signature Register <23:0> (read only)
0xBB
Open <15:0>
BIST Control <15:0>
Output Port Register Map—Addresses 0xBC to 0xE7
0xBF
Open <7:0>
Parallel Port Output Control <23:0>
0xC3
Open <15:0>
Open <15:10>, Output Port Control <9:0>
0xC7
AGC0, I Output <15:0> (read only)
AGC0, Q Output <15:0> (read only)
0xCB
AGC1, I Output <15:0> (read only)
AGC1, Q Output <15:0> (read only)
0xCF
AGC2, I Output <15:0> (read only)
AGC2, Q Output <15:0> (read only)
0xD3
AGC3, I Output <15:0> (read only)
AGC3, Q Output <15:0> (read only)
0xD7
AGC4, I Output <15:0> (read only)
AGC4, Q Output <15:0> (read only)
0xDB
AGC5, I Output <15:0> (read only)
AGC5, Q Output <15:0> (read only)
0xDF
Open <15:12>, AGC0 RSSI Output <11:0> (read only)
Open <15:12>, AGC1 RSSI Output <11:0> (read only)
0xE3
Open <15:12>, AGC2 RSSI Output <11:0> (read only)
Open <15:12>, AGC3 RSSI Output <11:0> (read only)
0xE7
Open <15:12>, AGC4 RSSI Output <11:0> (read only)
Open <15:12>, AGC5 RSSI Output <11:0> (read only)
Rev. 0 | Page 73 of 88
8-Bit Hex
Address
0x00
0x04
0x08
0x0C
0x10
0x48
0x4C
0x50
0x54
0x68
0x6C
0x70
0x74
0x78
0x7C
0x80
0x84
0x88
0x8C
0x90
0x94
0x98
0x9C
0xA0
0xA4
0xA8
0xAC
0xB0
0xB4
0xB8
0xBC
0xC0
0xC4
0xC8
0xCC
0xD0
0xD4
0xD8
0xDC
0xE0
0xE4
AD6654
one channel has access, the read access is given to the channel
with the lowest channel number.
GLOBAL REGISTER MAP
Chip I/O Access Control Register <7:0>
<7>: Synchronous Microport Bit. When this bit is set, the
microport assumes that its control signals (such as R/W, DS,
and CS,) are synchronous to the CPUCLK. When cleared,
asynchronous control signals are assumed, and the microport
control signals are resynchronized with CPUCLK inside the
AD6654 part. Synchronous microport (when bit is set) has the
advantage of requiring a fewer number of clock cycles for
read/write access.
<6>: This bit is open.
<5:2>: Chip ID Bits. The chip ID bits are used to compare
against the chip ID input pins (CHIPID), enabling or disabling
I/O access for this specific chip. When more than one AD6654
part is sharing the microport, different CHIPID pins can be
used to differentiate among the parts. A particular part gives
I/O access only when the CHIPID pins have the same value as
these chip ID bits.
For example, if both Channel 4 and Channel 2 have access bits
set, then read access is given to Channel 2.
Channel Enable Register <5:0>
<5>: Channel 5 Enable Bit. When this bit is set, Channel 5 logic
is enabled. When this bit is cleared, Channel 5 is disabled and
the channel’s logic does not consume any power. On power-up,
this bit comes up with Logic 0 and the channel is disabled. A
start sync does not start Channel 5, unless this bit is set before
issuing the start sync.
<4>: Channel 4 Enable Bit. Similar to Bit <5> for Channel 4.
<3>: Channel 3 Enable Bit. Similar to Bit <5> for Channel 3.
<2>: Channel 2 Enable Bit. Similar to Bit <5> for Channel 2.
<1>: Channel 1 Enable Bit. Similar to Bit <5> for Channel 1.
<0>: Channel 0 Enable Bit. Similar to Bit <5> for Channel 0.
<1>: This bit is open.
Pin Synchronization Configuration <7:0>
<0>: Byte Mode Bit. The byte mode bit selects the bit width for
the microport operation. Table 29 shows details.
Table 29. Microport Data Bus Width Selection
Chip Access Control
Register <0>
0 (default)
1
Microport Data Bus Bit Width
8-bit mode, using D <7:0>
16-bit mode, using D <15:0>
Channel I/O Access Control Register <5:0>
These bits enable/disable the channel I/O access capability.
<5>: Channel 5 Access Bit. When the Channel 5 access bit is set
to Logic 1, any I/O write operation (from either the microport
or the serial port) that addresses a register located within the
channel register map updates the Channel 5 registers. Similarly,
for a read operation, the contents of the desired address in the
channel register map are output when this bit is set to Logic 1.
<4>: Channel 4 Access Bit. Similar to Bit <5> for Channel 4.
<7>: Hop Synchronization Enable Bit. This bit is a global enable
for any hop synchronization involving SYNC pins. When this
bit is set, hop synchronization is enabled for all channels that
are programmed for pin synchronization. When this bit is
cleared, hop synchronization is not performed for any channel
that is programmed for pin synchronization.
<6>: Start Synchronization Enable Bit. This bit is a global enable
for any start synchronization involving SYNC pins. When this
bit is set, start synchronization is enabled for all channels that
are programmed for pin synchronization. When this bit is
cleared, start synchronization is not performed for any channel
that is programmed for pin synchronization.
<5>: First Sync Only Bit. When this bit is set, the NCO synchronization logic recognizes only the first synchronization event as
valid. All other requests for synchronization events are ignored
as long as this bit is set. When cleared, all synchronization
events are acted upon.
<4>: Edge-Sensitivity Bit. When this bit is set, the rising edge on
the SYNC pin(s) is detected as a synchronization event (edgesensitive detection). When cleared, Logic 1 on the SYNC pin(s)
is detected as a synchronization event (level-sensitive
detection).
<3>: Channel 3 Access Bit. Similar to Bit <5> for Channel 3.
<2>: Channel 2 Access Bit. Similar to Bit <5> for Channel 2.
<1>: Channel 1 Access Bit. Similar to Bit <5> for Channel 1.
<0>: Channel 0 Access Bit. Similar to Bit <5> for Channel 0.
Note: If the access bits are set for more than one channel, during
write access all channels with access are written with the same
data. This is especially useful when more than one channel has
similar configurations. During a read operation, if more than
<3>: Enable Synchronization from SYNC3 Bit. When this bit is
set, the SYNC3 pin can be used for synchronization. When this
bit is cleared, the SYNC3 pin is ignored. This is a global enable
for all SYNC pins, and each individual channel selects which
pin it listens to.
Rev. 0 | Page 74 of 88
AD6654
<2>: Enable Synchronization from SYNC2 Bit. Similar to
Bit <3> for the SYNC2 pin.
update interrupt enable bit is cleared, then this bit is not set (not
updated). An interrupt is not generated in this case.
<1>: Enable Synchronization from SYNC1 Bit. Similar to
Bit <3> for the SYNC1 pin.
Note: For Bits <15:10>, no interrupt is generated, if the new
RSSI word is the same as the previous RSSI word.
<0>: Enable Synchronization from SYNC0 Bit. Similar to
Bit <3> for the SYNC0 pin.
<14>: AGC4 RSSI Update Interrupt Bit. Similar to Bit <15> for
the AGC4.
Soft Synchronization Configuration <7:0>
<13>: AGC3 RSSI Update Interrupt Bit. Similar to Bit <15> for
the AGC3.
<7>: Soft Hop Synchronization Enable Bit. When this bit is set,
hop synchronization is enabled for all channels selected using
Bit 5 through Bit 0. When this bit is cleared, hop synchronization is not performed for any channels selected using Bit 5 to
Bit 0.
<6>: Soft Start Synchronization Enable Bit. When this bit is set,
start synchronization is enabled for all channels selected using
Bit 5 through Bit 0. When this bit is cleared, start synchronization
is not performed for any channels selected using Bit 5 to Bit 0.
<12>: AGC2 RSSI Update Interrupt Bit. Similar to Bit <15> for
the AGC2.
<11>: AGC1 RSSI Update Interrupt Bit. Similar to Bit <15> for
the AGC1.
<10>: AGC0 RSSI Update Interrupt Bit. Similar to Bit <15> for
the AGC0.
<5>: Soft Sync Channel 5 Enable Bit. When this bit is set, it
enables Channel 5 to receive a hop sync or start sync, as defined
by Bit 7 and Bit 6, respectively. When cleared, Channel 5 does
not receive any soft sync.
<9>: Channel 5 Data Ready Interrupt Bit. This bit is set to
Logic 1 whenever the channel BIST signature registers are
loaded with data. The conditions required for setting this bit are
that the channel BIST signature registers are programmed for
BIST signature generation and the Channel 5 data ready enable
bit in the interrupt enable register is cleared. If the Channel 5
data ready enable bit in the interrupt enable register is set, the
AD6654 does not set this bit on signature generation and an
interrupt is not generated.
<4>: Soft Sync Channel 4 Enable Bit. Similar to Bit <5> for
Channel 4.
<8>: Channel 4 Data Ready Interrupt Bit. Similar to Bit <9> for
Channel 4.
<3>: Soft Sync Channel 3 Enable Bit. Similar to Bit <5> for
Channel 3.
<7>: Channel 3 Data Ready Interrupt Bit. Similar to Bit <9> for
Channel 3.
<2>: Soft Sync Channel 2 Enable Bit. Similar to Bit <5> for
Channel 2.
<6>: Channel 2 Data Ready Interrupt Bit. Similar to Bit <9> for
Channel 2.
<1>: Soft Sync Channel 1 Enable Bit. Similar to Bit <5> for
Channel 1.
<5>: Channel 1 Data Ready Interrupt Bit. Similar to Bit <9> for
Channel 1.
<0>: Soft Sync Channel 0 Enable Bit. Similar to Bit <5> for
Channel 0.
<4>: Channel 0 Data Ready Interrupt Bit. Similar to Bit <9> for
Channel 0.
<10:0>: Reserved.
<3>: Reserved. This bit must be written with Logic 0.
<10:9>: Reserved. This bit must be written with Logic 1.
<2>: ADC Port Power Monitoring Interrupt Bit. This bit is set
by the AD6654 whenever the ADC port power monitor
interrupt enable bit is set and the ADC port power monitor
timer runs out (end of the ADC port power monitor period). If
the ADC port power monitor interrupt enable bit is cleared, the
AD6654 does not set this bit and does not generate an interrupt.
Bits <5:0> form the SOFT_SYNC control bits. These bits can be
written to by the controller to initiate the synchronization of a
selected channel.
<8:0>: Reserved. This bit must be written with Logic 0.
Interrupt Status Register <15:0>
This register is read only.
<15>: AGC5 RSSI Update Interrupt Bit. If the AGC5 update
interrupt enable bit is set, this bit is set by the AD6654
whenever AGC5 updates a new RSSI word (the new word
should be different from the previous word). If the AGC5
<1>: Reserved. This bit must be written with Logic 0.
<0>: Reserved. This bit must be written with Logic 0.
Rev. 0 | Page 75 of 88
AD6654
Interrupt Enable Register <15:0>
INPUT PORT REGISTER MAP
<15>: AGC5 RSSI Update Enable Bit. When this bit is set, the
AGC5 RSSI update interrupt is enabled, allowing an interrupt
to be generated when the RSSI word is updated.
ADC Input Control Register <27:0>
When this bit is cleared, an interrupt cannot be generated for
this event. Also, see the Interrupt Status Register <15:0> section.
<27>: PN Active Bit. When this bit is set, the pseudorandom
number generator is active. When this bit is cleared, the PN
generator is disabled and the seed is set to its default value.
<14>: AGC4 RSSI Update Enable Bit. Similar to Bit <15> for
the AGC4.
<13>: AGC3 RSSI Update Enable Bit. Similar to Bit <15> for
the AGC3.
<12>: AGC2 RSSI Update Enable Bit. Similar to Bit <15> for
the AGC2.
<11>: AGC1 RSSI Update Enable Bit. Similar to Bit <15> for
the AGC1.
<10>: AGC0 RSSI Update Enable Bit. Similar to Bit <15> for
the AGC0.
<9>: Channel 5 Data Ready Enable Bit. When this bit is set, the
Channel 5 data ready interrupt is enabled, allowing an interrupt
to be generated when Channel 5 BIST signature registers are
updated. When this bit is cleared, an interrupt cannot be
generated for this event.
<8>: Channel 4 Data Ready Enable Bit. Similar to Bit <9> for
Channel 4.
These bits are general control bits for the ADC input logic.
<26>: EXP Lock Bit. When this bit is set along with the PN
active bit, then the EXP signal for pseudorandom input is
locked to 000 (giving full-scale input). When this bit is cleared,
EXP bits for pseudorandom input are randomly generated input
data bits.
<25> Reserved. This bit must be written with Logic 0.
<24> Reserved. This bit must be written with Logic 0.
<23:20>: Channel 5 Cross Bar Mux Select Bits. These bits select
the source of input data for Channel 5. See Table 30.
Table 30. Input Data Source Selection
Cross Bar Mux Select Bits
0010
0100
Configuration
ADC port drives input (real)
PN sequence drives input (real)
<19>: Reserved. This bit must be written with Logic 0.
<18:16>: Channel 4 Cross Bar Mux Select Bits. Similar to bits
<22:20>, but for Channel 4.
<15>: Reserved. This bit must be written with Logic 0.
<7>: Channel 3 Data Ready Enable Bit. Similar to Bit <9> for
Channel 3.
<14:12>: Channel 3 Cross Bar Mux Select Bits. Similar to
Bits <22:20> for Channel 3.
<6>: Channel 2 Data Ready Enable Bit. Similar to Bit <9> for
Channel 2.
<11>: Reserved. This bit must be written with Logic 0.
<5>: Channel 1 Data Ready Enable Bit. Similar to Bit <9> for
Channel 1.
<10:8>: Channel 2 Cross Bar Mux Select Bits. Similar to
Bits <22:20> for Channel 2.
<4>: Channel 0 Data Ready Enable Bit. Similar to Bit <9> for
Channel 0.
<7>: Reserved. This bit must be written with Logic 0.
<3>: Reserved. This bit must be written with Logic 0.
<6:4>: Channel 1 Cross Bar Mux Select Bits. Similar to
Bits <22:20> for Channel 1.
<2>: ADC Port Power Monitoring Enable Bit. When this bit is
set to Logic 1, the ADC port power monitoring interrupt is
enabled, allowing an interrupt to be generated when ADC port
power monitoring registers are updated. When set to Logic 1,
the ADC port power monitoring interrupt is disabled.
<3>: Reserved. This bit must be written with Logic 0.
<1>: Reserved. This bit must be written with Logic 0.
These bits control the ADC clocks and internal PLL clock.
<0>: Reserved. This bit must be written with Logic 0.
<11>: Reserved. This bit must be written with Logic 0.
<2:0>: Channel 0 Cross Bar Mux Select Bits. Similar to
Bits <22:20> for Channel 0.
ADC CLK Control Register <11:0>.
Rev. 0 | Page 76 of 88
AD6654
<10>: ADC Port CLK Invert Bit. When this bit is set, the
inverted ADC port clock is used to register ADC input data into
the part. When this bit is cleared, the clock is used as is, without
any inversion or phase change.
ADC Port Power Monitor Period <23:0>
<9>: Reserved. This bit must be written with Logic 0.
This register is used in the power monitoring logic to set the
period of time for which ADC input data is monitored. This
value represents the monitor period in number of ADC port
clock cycles.
<8>: Reserved. This bit must be written with Logic 0.
ADC Port Power Monitor Output <23:0>
<7:6>: ADC Pre PLL Clock Divider Bits.: These bits control the
PLL clock divider. The PLL clock is derived from the ADC data
port CLK.
This register is read only and contains the current status of the
power monitoring logic output. The output is dependent on the
power monitoring mode selected. When the power monitor
block is enabled, this register is updated at the end of each
power monitor period. This register is updated even if an
interrupt signal is not generated.
Table 31. Divide-by Values for PLL Clock Divider Bits
PLL Clock Divider Bits <12:11>
00
01
10
11
Divide-by Value
Divide by 1, bypass
Divide by 2
Divide by 4
Divide by 8
ADC Port Upper Threshold <9:0>
<5:1>: PLL Clock Multiplier Bits. These bits control the PLL
clock multiplier. The output of the PLL clock divider is
multiplied with the binary value of these bits. Valid range for
the multiplier is from 4 to 20. A value outside this range powers
down the PLL, resulting in the PLL clock being the same as the
ADC data port CLK.
<0>: This bit is open.
This register serves the dual purpose of specifying the upper
threshold value in the gain control block and in the power
monitoring block, depending on which block is active. ADC
port input data having a magnitude greater than this value
triggers a gain change in the gain control block. ADC port input
data having a magnitude greater than this value is monitored in
the power monitoring block (in peak detect or threshold
crossing mode). The value of the register is compared with the
absolute magnitude of the input port data.
ADC Port Lower Threshold <9:0>
ADC Port Gain Control <7:0>
<7>: This bit is open.
<6:1>: This 6-bit word specifies the relinearization pipe delay to
be used in the ADC input gain control block. The decimal
representation of these bits is the number of input clock cycle
pipeline delays between the external EXP data output and the
internal application of relinearization based on EXP.
<0>: Gain Control Enable Bit. This bit controls the configuration of the EXP<2:0> bits for the ADC input port. When the
gain control enable bit is Logic 1, the EXP<2:0> bits are
configured as outputs. When this bit is cleared, the EXP<2:0>
bits are inputs.
ADC Port Dwell Timer <19:0>
This register is used to set the dwell time for the gain control
block. When the gain control block is active and detects a
decrease in the signal level below the lower threshold value
(programmable), a dwell-time counter is initiated to provide
temporal hysteresis. Doing so prevents the gain from being
continuously switched. Note that the dwell timer is turned on
only after a drop below the lower threshold is detected in the
signal level.
This register is used in the gain control block and represents the
magnitude of the lower threshold for ADC port input data. Any
ADC input data having a magnitude below the lower threshold
initiates the dwell time counter. The value of the register is
compared with the absolute magnitude of the input port data.
ADC Port Signal Monitor <4:0>
This register controls the functions of the power monitoring
block.
<4>: Disable Power Monitor Period Timer Bit. When this bit is
set, the power monitor period timer no longer controls the
update of the power monitor holding register. A user read to the
power monitor holding register updates this register. When this
bit is cleared, the power monitor period register controls the
timer and, therefore, controls the update rate of the power
monitor holding register.
<3>: Clear-on-Read Bit. When this bit is set, the power monitor
holding register is cleared every time this register is read. This
bit controls whether the power monitoring function is cleared
after a read of the power monitor period register. If this bit is
set, the monitoring function is cleared after the read. If this bit
is Logic 0, the monitoring function is not cleared. This bit is a
don’t care bit, if the disable integration counter bit is cleared.
Rev. 0 | Page 77 of 88
AD6654
<2:1>: Monitor Function Select Bits. Table 32 describes the
function of these bits.
bit is cleared, the accumulator is not cleared and phase
continuous hops are implemented.
Table 32. Monitor Function Select Bits
<1>: Phase Dither Enable Bit. When this bit is set, phase
dithering in the NCO is enabled. When this bit is cleared, phase
dithering is disabled.
Monitor Function Select
00
01
10
11
Function Enabled
Peak detect mode
Mean power monitor mode
Threshold crossing mode
Invalid selection
<0>: Monitor Enable Bit. When this bit is set, the power
monitoring function is enabled and operates as selected by Bit 2
to Bit 1 of the signal monitor register. When this bit is cleared,
the power monitoring function is disabled and the signal
monitor register bits <2:1> are don’t care bits. These bits default
to 0 on power-up.
<0>: Amplitude Dither Enable Bit. When this bit is set,
amplitude dithering in the NCO is enabled. When this bit is
cleared, amplitude dithering is disabled.
Channel Start Hold-Off Counter <15:0>
When a start synchronization (software or hardware) occurs on
the channel, the value in this register is loaded into a downcounter. When the counter has finished counting down to 0, the
channel operation is started.
CHANNEL REGISTER MAP
NCO Frequency Hop Hold-Off Counter <15:0>
Channel control registers are common to all six channels, and
access to specific channels is determined by the channel I/O
access register (Address 0x02).
When a hop sync occurs, a counter is loaded with the NCO
frequency hold-off register value. The 16-bit counter starts
counting down. When it reaches 0, the new frequency value in
the shadow register is written to the NCO frequency register.
(See the NCO Frequency Hold-Off Register section.)
NCO Control <15:0>
These bits control the NCO operation.
NCO Frequency <31:0>
<8:7>: NCO Sync Start Select Bits. These bits determine which
SYNC input pin is used by this channel for a start synchronization operation. Table 33 describes the selection.
The value in this register is used to program the NCO tuning
frequency. The value to be programmed is given by the
following equation:
Table 33. Sync Start Select Bits
NCO Control <8:7>
00
01
10
11
NCO Frequency Register =
SYNC Pin Used for Start
Synchronization
SYNC0
SYNC1
SYNC2
SYNC3
where:
NCO_FREQUENCY is the desired NCO tuning frequency.
CLK is the ADC clock rate.
<6:5>: NCO Sync Hop Select Bits. These bits determine which
SYNC input pin is used by this channel for a hop synchronization operation. Table 34 describes the selection.
Table 34. Sync Hop Select Bits
NCO Control <6:5>
00
01
10
11
NCO _ FREQUENCY
× 2 32
CLK
SYNC Pin Used for Hop
Synchronization
SYNC0
SYNC1
SYNC2
SYNC3
<4>: This bit is open.
<3>: NCO Bypass Bit. When this bit is set, the NCO is bypassed
and shuts down for power savings. This bit can be used for
power savings, when NCO frequency of dc or 0 Hz is required.
When this bit is cleared, the NCO operates as programmed.
<2>: Clear NCO Accumulator Bit. When this bit is set, the clear
NCO accumulator bit synchronously clears the phase
accumulator on all frequency hops in this channel. When this
The value given by the equation should be loaded into the
register in binary format.
NCO Phase Offset <15:0>
The value in the register is loaded into the phase accumulator of
the NCO block every time a start sync or hop sync is received
by the channel. This allows individual channels to be started
with a known nonzero phase. The NCO phase offset is not
loaded on a hop sync, if Bit <2> of the NCO control register
(clear phase accumulator on hop) is cleared. This NCO offset
register value is interpreted as a 16-bit unsigned integer. A
0x0000 in this register corresponds to a 0 radian offset, and a
0xFFFF corresponds to an offset of 2π (1 − 1/(216)) radians.
CIC Bypass <0>
When this bit is set, the entire CIC filter is bypassed. The output
of CIC filter is driven straight from the input without any
change. When this bit is cleared, the CIC filter operates in
normal mode as programmed. Writing Logic 1 to this bit
disables both the CIC decimation and CIC scaling operations.
Rev. 0 | Page 78 of 88
AD6654
CIC Decimation <4:0>
<8>: This bit is open.
This 5-bit word specifies the CIC filter decimation value
minus 1. A value of 0x00 is a decimation of 1 (bypass), and
0x1F is a decimation of 32. Writing a value of 0 in this register
bypasses CIC filtering, but does not bypass the CIC scaling
operation.
<7>: Half-Rate Bit. When this bit is set, the MRCF filter
operates using half the PLL clock rate. This is used for power
savings when there is sufficient time to complete MRCF
filtering using only half the PLL clock rate. When this bit is
cleared, the MRCF filter operates at the full PLL clock rate. See
the Mono-Rate RAM Coefficient Filter (MRCF) section.
CIC Scale Factor <4:0>
<6:4>: MRCF Number of Taps Bits. This 3-bit word should be
written with one less than the number of taps that are calculated
by the MRCF filter. The filter length is given by the decimal
value of this register plus 1. A value of 0 represents a 1-tap filter
and maximum value of 7 represents an 8-tap filter.
This 5-bit word specifies the CIC filter scale factor used to
compensate for the gain provided by the CIC filter. The
recommended value is given by the following equation:
CIC Scale Register = ceil (5 × log 2 ( M CIC )) − 5
where:
MCIC is the decimation rate of the CIC (one more than the value
in the CIC decimation register).
ceil operation gives the closest integer greater than or equal to
the argument.
The valid range for this register is decimal 0 to 20.
FIR-HB Control <3:0>
<3>: FIR1 Enable Bit. When this bit is set, the FIR1 fixed
coefficient filter is enabled. When cleared, FIR1 is bypassed.
Table 36. MRCF Scale Factor
MRCF Scale<1:0>
00
01
10
11
Scale Factor
18.06 dB attenuation (left-shift 3 bits)
12.04 dB attenuation (left-shift 2 bits)
6.02 dB attenuation (left-shift 1 bit)
No scaling (0 dB)
<1>: This bit is open.
<2>: HB1 Enable Bit. When this bit is set, the HB1 half-band
filter is enabled. When cleared, HB1 is bypassed.
<1>: FIR2 Enable Bit. When this bit is set, the FIR2 fixed
coefficient filter is enabled. When cleared, FIR2 is bypassed.
<0>: MRCF Bypass Bit. When this bit is set, the MRCF filter is
bypassed and, therefore, the output of the MRCF is the same as
its input. When this bit is cleared, the MRCF has normal
operation as programmed by its control register.
MRCF COEFFICIENT MEMORY
<0>: HB2 Enable Bit. When this bit is set, the HB2 half-band
filter is enabled. When cleared, HB2 is bypassed.
MRCF Control Register <12:0>
<12:10>: MRCF Data Select Bits. These bits are used to select
the input source for the MRCF filter. Each MRCF filter can be
driven by output from the HB2 filter of any channel independently. Table 35 shows the selections available.
Table 35. MRCF Data Select Bits
MRCF Data Select<2:0>
000
001
010
011
1x0
1x1
<3:2>: MRCF Scale Factor Bits. The output of the MRCF filter is
scaled according to the value of these bits. Table 36 describes
the attenuation corresponding to each setting.
MRCF Input Source
MRCF input taken from Channel 0
MRCF input taken from Channel 1
MRCF input taken from Channel 2
MRCF input taken from Channel 3
MRCF input taken from Channel 4
MRCF input taken from Channel 5
<9>: Interpolating Half-Band Enable Bit. When this bit is set,
the interpolating half-band filter, driven by the output of the
CRCF block, is enabled. When cleared, the interpolating halfband filter is bypassed, and its output is the same as its input.
The interpolating half-band filter doubles the data rate.
The MRCF coefficient memory consists of eight coefficients,
each six bits wide. The memory extends from Address 0x80 to
Address 0x87. The coefficients should be written in twos
complement format.
DRCF Control Register <11:0>
<11>: DRCF Bypass Bit. When this bit is set, the DRCF filter is
bypassed and, therefore, its output is the same as its input.
When this bit is cleared, the DRCF has normal operation as
programmed by the rest of this control register.
<10>: Symmetry Bit. When this bit is set, it indicates that the
DRCF is implementing a symmetrical filter and only half the
impulse response needs to be written into the DRCF coefficient
RAM. When this bit is cleared, the filter is asymmetrical and
complete impulse response of the filter should be written to the
coefficient RAM. When this filter is symmetrical, it can implement up to 128 filter taps.
<9:8>: DRCF Multiply Accumulate Scale Bits. The output of the
DRCF filter is scaled according to the value of these bits.
Table 37 lists the attenuation corresponding to each setting.
Rev. 0 | Page 79 of 88
AD6654
Table 37. DRCF Multiply Accumulate Scale Bits
CRCF Control Register <11:0>
DRCF Scale <1:0>
00
01
10
11
<11>: CRCF Bypass Bit. When this bit is set, the DRCF filter is
bypassed and, therefore, its output is the same as its input.
When this bit is cleared, the CRCF has normal operation as
programmed by its control register.
Scale Factor
18.06 dB attenuation (left-shift 3 bits)
12.04 dB attenuation (left-shift 2 bits)
6.02 dB attenuation (left-shift 1 bit)
No scaling (0 dB)
<7:4>: DRCF Decimation Rate. This 4-bit word should be
written with one less than the decimation rate of the DRCF
filter. A value of 0 represents a decimation rate of 1 (no rate
change), and the maximum value of 15 represents a decimation
of 16. Filtering can be implemented regardless of the
decimation rate.
<3:0>: DRCF Decimation Phase Bits. This 4-bit word represents
the decimation phase used by the DRCF filter. The valid range
is 0 up to MDRCF − 1, where MDRCF is the decimation rate of the
DRCF filter. This word is primarily used for synchronization of
multiple channels of the AD6654, when more than one channel
is used for filtering one signal (one carrier).
DRCF Coefficient Offset <7:0>
This register is used to specify which section of the 64-word
coefficient memory is used for a filter. It can be used to select
between multiple filters that are loaded into memory and
referenced by this pointer. This register is shadowed, and the
filter pointer is updated every time a new filter is started. This
allows the coefficient offset to be written even while a filter is
being computed without disturbing operation. The next sample
comes out of the DRCF with the new filter.
DRCF Taps <6:0>
This register is written with one less than the number of taps
that are calculated by the DRCF filter. The filter length is given
by the decimal value of this register plus 1. A value of 0
represents a 1-tap filter, and a value of 0x28 (40 decimal)
represents a 41-tap filter.
DRCF Start Address <5:0>
This register is written with the starting address of the DRCF
coefficient memory to be updated.
DRCF Final Address <5:0>
This register is written with the ending address of the DRCF
coefficient memory to be updated.
<10>: Symmetry Bit. When this bit is set, it indicates that the
CRCF is implementing a symmetrical filter and only half the
impulse response needs to be written into the CRCF coefficient
RAM. When this bit is cleared, the filter is asymmetrical and
the complete impulse response of the filter should be written
into the coefficient RAM. When this filter is symmetrical, it can
implement up to 128 filter taps.
<9:8>: CRCF Multiply Accumulate Scale Bits. The output of the
CRCF filter is scaled according to the value of these bits.
Table 38 lists the attenuation corresponding to each setting.
Table 38. CRCF Multiply Accumulate Scale Bits
CRCF Scale<1:0>
00
01
10
11
Scale Factor
18.06 dB attenuation (left-shift 3 bits)
12.04 dB attenuation (left-shift 2 bits)
6.02 dB attenuation (left-shift 1 bit)
No scaling (0 dB)
<7:4>: CRCF Decimation Rate. This 4-bit word should be written with one less than the decimation rate of the CRCF filter. A
value of 0 represents a decimation rate of 1 (no rate change) and
the maximum value of 15 represents a decimation of 16.
Filtering operation is done regardless of the decimation rate.
<3:0>: CRCF Decimation Phase. This 4-bit word represents the
decimation phase used by the CRCF filter. The valid range is 0
to MCRCF − 1, where MCRCF is the decimation rate of the
CRCF filter. This word is primarily used for synchronization of
multiple channels of the AD6654, when more than one channel
is used for filtering one signal (one carrier).
CRCF Coefficient Offset <5:0>
This register is used to specify which section of the 64-word
coefficient memory is used for a filter. It can be used to select
between multiple filters that are loaded into memory and
referenced by this pointer. This register is shadowed, and the
filter pointer is updated every time a new filter is started. This
allows the coefficient offset to be written even while a filter is
being computed without disturbing operation. The next sample
comes out of the CRCF with the new filter.
DRCF Coefficient Memory <13:0>
DRCF Memory. This memory consists of 64 words, and each
word is 14 bits wide. The data written to this memory space is
expected to be 14-bit, twos complement format. See the
Decimating RAM Coefficient Filter (DRCF) section for the
method to program the coefficients into the coefficient
memory.
CRCF Taps <6:0>
This register is written with one less than the number of taps
that are calculated by the CRCF filter. The filter length is given
by the decimal value of this register plus 1. A value of 0 represents a 1-tap filter, and a value of 0x28 (40 decimal) represents a
41-tap filter.
Rev. 0 | Page 80 of 88
AD6654
CRCF Coefficient Memory
CRCF Memory. This memory has 64 words that have 20 bits
each. The memory contains the CRCF filter coefficients. The
data written to this memory space is 20-bit in twos complement
format. See the Channel RAM Coefficient Filter (CRCF) section
for the method to program the coefficients into the coefficient
memory.
AGC Control Register <10:0>
<10>: Channel Sync Select Bit. When this bit is set, the AGC
uses the sync signal from the channel for its synchronization.
When this bit is cleared, the SYNC pin used for synchronization
is defined by Bit 9 to Bit 8 of this register.
Table 39. SYNC Pin Select Bits
AGC Hold-Off Register <15:0>
SYNC Pin Used by AGC
SYNC0
SYNC1
SYNC2
SYNC3
<7:5>: AGC Word Length Control Bits. These bits define the
word length of the AGC output. The output word can be 4 to 8,
10, 12, or 16 bits wide. Table 40 shows the possible selections.
Table 40. AGC Word Length Control Bits
AGC Control Bits <7:5>
000
001
010
011
100
101
110
111
<1>: First Sync Only. This bit is used to ignore repetitive
synchronization signals. In some applications, the synchronization signal occurs periodically. If this bit is cleared, each
synchronization request resynchronizes the AGC. If this bit is
set, only the first occurrence causes the AGC to synchronize
and updates the AGC gain values periodically, depending on
the decimation factor of the AGC CIC filter.
<0>: AGC Bypass Bit. When this bit is set, the AGC section is
bypassed. The N-bit representation from the interpolating halfband filters is still reduced to a lower bit width representation as
set by Bit 7 to Bit 5 of the AGC control register. A truncation at
the output of the AGC accomplishes this task.
<9:8>: SYNC Pin Select Bits. When Bit 10 of this register is
cleared, these bits specify the SYNC pin used by AGC for
synchronization. These bits are don’t care when Bit 10 of the
AGC control register is set to Logic 1.
AGC Control Bits <9:8>
00
01
10
11
When Bit 2 = 0, the above-mentioned parameters are not
updated, and the CIC filter is not cleared. In both cases, an
AGC update sample is output from the CIC filter and the
decimator starts operating towards the next output sample
whenever a sync occurs.
Output Word Length (Bits)
16
12
10
8
7
6
5
4
<4>: AGC Mode Bit. When this bit is cleared, the AGC operates
to maintain a desired signal level. When this bit is set, it
operates to maintain a constant clipping level. See the
Automatic Gain Control section for details about these modes.
<3>: AGC Sync Now Bit. This bit is used to synchronize a
particular AGC, regardless of the channel, through the
programming ports (microport or serial port). When this bit is
set, the AGC block updates a new output sample (RSSI sample)
and starts working toward a new update sample.
<2>: Initialize on Sync Bit. This bit is used to determine
whether or not the AGC should initialize on a sync. When this
bit is set, during a synchronization the CIC filter is cleared and
new values for CIC decimation, number of averaging samples,
CIC scale, Signal Gain K, and the Pole P parameter are loaded.
The AGC hold-off counter is loaded with the value written to
this address when either a soft sync or pin sync comes into the
channel. The counter begins counting down. When it reaches 1,
a sync is sent to the AGC. This sync might or might not initialize the AGC, as defined by the control word. The AGC loop is
updated with a new sample from the CIC filter whenever a sync
occurs. If this register is Logic 1, the AGC is immediately
updated when the sync occurs. If this register is Logic 0, the
AGC cannot be synchronized.
AGC Update Decimation <11:0>
This 12-bit register sets the AGC decimation ratio from 1 to
4096. An appropriate scaling factor should be set to avoid loss
of bits. The decimation ratio is given by the decimal value of the
AGC update decimation<11:0> register contents plus 1, that is,
12’0x000 describes a decimation ratio of 1, and 12’0xFFF
describes a decimation ratio of 4096.
AGC Signal Gain <11:0>
This register is used to set the initial value for a signal gain used
in the gain multiplier. This 12-bit value sets the initial signal
gain in the range of 0 dB and 96.296 dB in steps of 0.024 dB.
Initial signal gain (SG) in dB should be converted to a register
setting using the following formula:
⎡
⎤
SG
Register Value = round ⎢
× 256⎥
⎣ 20 log10 (2)
⎦
AGC Error Threshold <11:0>
This 12-bit register is the comparison value used to determine
which loop gain value (K1 or K2) to use for optimum operation.
When the magnitude-of-error signal is less than the AGC error
threshold value, then K1 is used; otherwise, K2 is used. The word
Rev. 0 | Page 81 of 88
AD6654
format of the AGC error threshold register is four bits to the left
of the binary point and eight bits to the right.
See the Automatic Gain Control section for details.
⎡ Error Threshold ⎤
Register Value = round ⎢
⎥ × 256
⎢⎣ 20 log 10 (2) ⎥⎦
AGC Loop Gain 1 <7:0>
This 8-bit register is used to define K1, the open-loop gain. Its
value can be set from 0 to 0.996 in steps of 0.0039. This value of
K is updated in the AGC loop each time the AGC is initialized.
When the magnitude-of-error signal in the loop is less than the
AGC error threshold, then K1 is used by the loop. K1 is updated
only when the AGC is initialized.
AGC Average Samples <5:0>
I Path Signature Register <15:0>
This 6-bit register contains the scale used for the CIC filter and
the number of power samples to be averaged before being sent
to the CIC filter.
This 16-bit signature register is for the I path of the channel
logic. The signature register records data on the networks that
leave the channel logic, just before entering the second data
router.
<5:2>: CIC Scale. This 4-bit word defines the scale used for the
CIC filter. Each increment of this word increases the CIC scale
by 6.02 dB.
<1:0>: Number of AGC Average Samples. This defines the
number of samples to be averaged before they are sent to the
CIC decimating filter. See Table 41.
Table 41. Number of AGC Average Samples
AGC Average Samples <1:0>
00
01
10
11
Number of Samples Taken
1
2
3
4
AGC Pole Location <7:0>
Q Path Signature Register <15:0>
This 16-bit signature register is for the Q path of the channel
logic. The signature register records data on the networks that
leave the channel logic, just before entering the second data
router.
BIST Control <15:0>
<15>: Disable Signature Generation Bit. When this bit is active
high, the signature registers do not produce a pseudorandom
output value, but instead directly load the 24-bit input data.
When this bit is cleared, the signature register produces a
pseudorandom output for every clock cycle that it is active. See
the User-Configurable Built-In Self-Test (BIST) section for
details.
This 8-bit register is used to define P, the open-loop filter pole
location. Its value can be set from 0 to 0.996 in steps of 0.0039.
This value of P is updated in the AGC loop each time the AGC
is initialized. This open-loop pole location directly impacts the
closed-loop pole locations, as explained in the Automatic Gain
Control section.
<14:0>: BIST Timer Bits. The <14:0> bits of this register form a
15-bit word that is loaded into the BIST timer. After loading the
BIST timer, the signature register is enabled for operation while
the timer is actively counting down. See the User-Configurable
Built-In Self-Test (BIST) section for details.
AGC Desired Level <7:0>
This part of the memory map deals with the output data and
controls for parallel output ports.
This register contains the desired signal level or desired clipping
level, depending on operational mode. This desired request
level (R) can be set in dB from 0 to 23.99 in steps of 0.094 dB.
The request level (R) in dB should be converted to a register
setting using the following formula:
⎡
⎤
R
× 64 ⎥
Register Value = round ⎢
⎣⎢ 20 log 10 (2)
⎦⎥
AGC Loop Gain 2 <7:0>
This 8-bit register is used to define K2, the second possible
open-loop gain. Its value can be set from 0 to 0.996 in steps of
0.0039. This value of K2 is updated each time the AGC is
initialized. When the magnitude-of-error signal in the loop is
greater than the AGC error threshold, then K2 is used by the
loop. K2 is updated only when the AGC is initialized.
OUTPUT PORT REGISTER MAP
Parallel Port Output Control <23:0>
<23>: Port C Append RSSI Bit. When this bit is set, an RSSI
word is appended to every I/Q output sample, regardless of
whether the RSSI word is updated in the AGC. When this bit is
cleared, an RSSI word is appended to an I/Q output sample only
when the RSSI word is updated. The RSSI word is not output for
subsequent I/Q samples until the next time the RSSI is updated
in the AGC.
<22>: Port C, Data Format Bit. When this bit is set, the port is
configured for 8-bit parallel I/Q mode. When cleared, the port
is configured for 16-bit interleaved I/Q mode. See the Parallel
Port Output section for details.
<21>: Port C, AGC5 Enable Bit. When this bit is set, AGC5
data (I/Q data) is output on parallel Output Port C (data bus).
Rev. 0 | Page 82 of 88
AD6654
When this bit is cleared, AGC5 data does not appear on Output
Port C.
<20>: Port C, AGC4 Enable Bit. Similar to Bit 21 for AGC4.
<3>: Port A, AGC3 Enable Bit. Similar to Bit 5 for AGC3.
<2>: Port A, AGC2 Enable Bit. Similar to Bit 5 for AGC2.
<1>: Port A, AGC1 Enable Bit. Similar to Bit 5 for AGC1.
<19>: Port C, AGC3 Enable Bit. Similar to Bit 21 for AGC3.
<0>: Port A, AGC0 Enable Bit. Similar to Bit 5 for AGC0.
<18>: Port C, AGC2 Enable Bit. Similar to Bit 21 for AGC2.
Output Port Control <9:0>
<17>: Port C, AGC1 Enable Bit. Similar to Bit 21 for AGC1.
<16>: Port C, AGC0 Enable Bit. Similar to Bit 21 for AGC0.
<15>: Port B Append RSSI Bit. When this bit is set, an RSSI
word is appended to every I/Q output sample, regardless of
whether the RSSI word is updated in the AGC. When this bit is
cleared, an RSSI word is appended to an I/Q output sample only
when the RSSI word is updated. The RSSI word is not output for
subsequent I/Q samples until the next time the RSSI is updated
in the AGC.
<14>: Port B, Data Format Bit. When this bit is set, the port is
configured for 8-bit parallel I/Q mode. When this bit is cleared,
the port is configured for 16-bit interleaved I/Q mode. See the
Parallel Port Output section.
<13>: Port B, AGC5 Enable Bit. When this bit is set, AGC5 data
(I/Q data) is output on Parallel Output Port A (data bus). When
this bit is cleared, AGC5 data does not appear on Output Port
C.
<9:8>: PCLK Divisor Bits. When a parallel port is in master
mode, the PCLK is derived from the PLL_CLK. These bits
define the value of the divisor used to divide the PLL_CLK to
obtain the PCLK. These bits are don’t care in slave mode.
Table 42. PCLK Divisor Bits
PCLK Divisor <7:6>
00
01
10
11
Divisor Value
1
2
4
8
<7>: PCLK Master Mode Bit. When the PCLK master mode bit
is set, the PCLK pin is configured as an output and the PCLK is
driven by the PLL_CLK. Data is transferred out of the AD6654
synchronous to this output clock. When this bit is cleared, the
PCLK pin is configured as an input. The user is required to
provide a PCLK, and data is transferred out of the AD6654
synchronous to this input clock. On power-up, this bit is cleared
to avoid contention on the PCLK pin.
<6:4>: Reserved. These bits must be written with Logic 0.
<12>: Port B, AGC4 Enable Bit. Similar to Bit 13 for AGC4.
<3:0>: Stream Control Bits. These bits are described in Table 43.
<11>: Port B, AGC3 Enable Bit. Similar to Bit 13 for AGC3.
Table 43. Stream Control Bits
<10>: Port B, AGC2 Enable Bit. Similar to Bit 13 for AGC2.
Stream
Control
Bits
0000
<9>: Port B, AGC1 Enable Bit. Similar to Bit 13 for AGC1.
<8>: Port B, AGC0 Enable Bit. Similar to Bit 13 for AGC0.
<7>: Port A Appended RSSI Bit. When this bit is set, an RSSI
word is append to every I/Q output sample, regardless of
whether the RSSI word is updated in the AGC. When this bit is
cleared, an RSSI word is appended to an I/Q output sample only
when the RSSI word is updated. The RSSI word is not output for
subsequent I/Q samples until the next time RSSI is updated
again in the AGC.
<6>: Port A, Data Format Bit. When this bit is set, the port is
configured for 8-bit parallel I/Q mode. When this bit is cleared,
the port is configured for 16-bit interleaved I/Q mode. See the
Parallel Port Output section.
<5>: Port A, AGC5 Enable Bit. When this bit is set, AGC5 data
(I/Q data) is output on parallel output Port A (data bus). When
this bit is cleared, AGC5 data does not appear on output Port C.
<4>: Port A, AGC4 Enable Bit. Similar to Bit 5 for AGC4.
0001
0010
0011
0100
0101
0110
0111
1000
1001
Default
Rev. 0 | Page 83 of 88
Output Streams (str0, str1, str2,
str3, str4, str5)
Ch 0 and Ch 1 combined; Ch 2, Ch 3,
Ch 4, Ch 5 independent
Ch 0, Ch 1, Ch 2 combined; Ch 3, Ch 4,
Ch 5 independent
Ch 0, Ch 1, Ch 2, Ch 3 combined; Ch 4,
Ch 5 independent
Ch 0, Ch 1, Ch 2, Ch 3, Ch 4 combined;
Ch 5 independent
Ch 0, Ch 1, Ch 2, Ch 3, Ch 4, Ch 5
combined
Ch 0, Ch 1, Ch 2 combined; Ch 3, Ch 4,
Ch 5 combined
Ch 0, Ch 1 combined; Ch 2, Ch 3
combined; Ch 4, Ch 5 combined
Ch 0, Ch 1 combined; Ch 2, Ch 3
combined; Ch 4, Ch 5 independent
Ch 0, Ch 1 , Ch 2 combined; Ch 3, Ch 4
combined; Ch 5 independent
Ch 0, Ch 1, Ch 2, Ch 3 combined; Ch 4,
Ch 5 combined.
Independent channels
Number of
Streams
5
4
3
2
1
2
3
4
3
2
6
AD6654
AGC0, I Output <15:0>
AGC4, Q Output <15:0>
This read-only register provides the latest in-phase output
sample from AGC0. Note that AGC0 might be bypassed, and
that AGC0 here is representative of the datapath only.
This read-only register provides the latest quadrature-phase
output sample from AGC4. Note that AGC4 might be bypassed
and that AGC4 here is representative of the datapath only.
AGC0, Q Output <15:0>
AGC5, I Output <15:0>
This read-only register provides the latest quadrature-phase
output sample from AGC0. Note that AGC0 might be bypassed,
and that AGC0 here is representative of the datapath only.
This read-only register provides the latest in-phase output
sample from AGC5. Note that AGC5 might be bypassed and
that AGC5 here is representative of the datapath only.
AGC1, I Output <15:0>
AGC5, Q Output <15:0>
This read-only register provides the latest in-phase output
sample from AGC1. Note that AGC1 might be bypassed and
that AGC1 here is representative of the datapath only.
This read-only register provides the latest quadrature-phase
output sample from AGC5. Note that AGC5 might be bypassed
and that AGC5 here is representative of the datapath only.
AGC1, Q Output <15:0>
AGC0, RSSI Output <11:0>
This read-only register provides the latest quadrature-phase
output sample from AGC1. Note that AGC1 might be bypassed
and that AGC1 here is representative of the datapath only.
This read-only register provides the latest RSSI output sample
from AGC0. This register is updated only when AGC0 is
enabled and operating.
AGC2, I Output <15:0:
AGC1, RSSI Output <11:0>
This read-only register provides the latest in-phase output
sample from AGC2. Note that AGC2 might be bypassed and
that AGC2 here is representative of the datapath only.
This read-only register provides the latest RSSI output sample
from AGC1. This register is updated only when AGC1is
enabled and operating.
AGC2, Q Output <15:0>
AGC2, RSSI Output <11:0>
This read-only register provides the latest quadrature-phase
output sample from AGC2. Note that AGC2 might be bypassed
and that AGC2 here is representative of the datapath only.
This read-only register provides the latest RSSI output sample
from AGC2. This register is updated only when AGC2 is
enabled and operating.
AGC3, I Output <15:0>
AGC3, RSSI Output <11:0>
This read-only register provides the latest in-phase output
sample from AGC3. Note that AGC3 might be bypassed and
that AGC3 here is representative of the datapath only.
This read-only register provides the latest RSSI output sample
from AGC3. This register is updated only when AGC3 is
enabled and operating.
AGC3, Q Output <15:0>
AGC4, RSSI Output <11:0>
This read-only register provides the latest quadrature-phase
output sample from AGC3. Note that AGC3 might be bypassed
and that AGC3 here is representative of the datapath only.
This read-only register provides the latest RSSI output sample
from AGC4. This register is updated only when AGC4 is
enabled and operating.
AGC4, I Output <15:0>
AGC5, RSSI Output <11:0>
This read-only register provides the latest in-phase output
sample from AGC4. Note that AGC4 might be bypassed and
that AGC4 here is representative of the datapath only.
This read-only register provides the latest RSSI output sample
from AGC5. This register is updated only when AGC5 is
enabled and operating.
Rev. 0 | Page 84 of 88
AD6654
DDC DESIGN NOTES
The following guidelines describe circuit connections, layout
requirements, and programming procedures for the AD6654.
The designer should review these guidelines before starting the
system design and layout.
•
The AD6654 requires the following power-up sequence.
The VDDCORE (1.8 V) is required to settle into nominal
voltage levels before the VDDIO attains the minimum.
•
The DDC input clock (CLK) and input (EXP) pins EXP[2:0]
are not 5 V tolerant. Care should be taken to drive these
pins within the limits of VDDIO (3.0 V to 3.6 V). This is
easily accomplished by using the ADC data ready (DR)
output to drive the DDC clock (CLK) input.
•
•
The number format used in this part is twos complement.
All input ports and output ports use twos complement data
format. The formats for individual internal registers are
given in the memory map description of these registers.
•
By default, the PLL CLK is disabled. It can be enabled by
programming the PLL multiplier and divider bits in the
ADC CLK control register. When the PLL CLK is enabled
by programming this register, it takes about 50 µs to 200 µs
to settle down. While the PLL loop settles down, the voltage
at the EXT_FILTER pin increases from 0 V to VDDCORE
(1.8 V) and settles there. Channel registers and output port
registers (Address 0x68 to Address 0xE7) should not be programmed before the PLL loop settles down.
•
To reset the AD6654, the user must provide a minimum
pulse of 30 ns to the RESET pin. The RESET pin should be
connected to GND (or pulled low) during power-up of the
part. The RESET pin can be pulled high after the power
supplies have settled to nominal values (1.8 V and
3.3 V). At this point, a pulse (pull low and high again)
should be provided to give a reset to the part.
•
The CPUCLK (SCLK) is the clock used for programming
via the microport (serial port). This clock needs to be
provided by the designer to the part (slave clock). The
designer should ensure that this clock’s frequency is less
than or equal to the frequency of the CLK signal. Additionally, the frequency of the CPUCLK (SCLK) should
always be less than 100 MHz.
•
The microport data bus is 16 bits wide. Both 8-bit and
16-bit modes are available using this part. If 8-bit mode is
used, the MSB of the data bus (D[15:8]) can be left floating
or connected to GND.
•
The output parallel port has a 1-clock cycle overhead. If two
channels (with the same data rates) are output on one
output port in 16-bit interleaved I/Q mode along with an
AGC word, this requires three clock cycles for one sample
from each channel (one clock each for I data, Q data, and
gain data). Therefore, the total number of clock cycles
required to output the data is 3 clocks/channel × 2 channels
+ 1 (overhead) = 7 clock cycles. The number of clock cycles
required for each channel can be 3 (interleaved I + Q + gain
word), or 2 (parallel I /Q + gain) or 2 (interleaved I + Q) or
1 (interleaved I/Q). Designers should make sure that sufficient time is allowed to output these channels on one output
port. Also note that the I, Q, and gain for a particular
channel come out on a single output port and cannot be
divided among output ports.
•
When CRCF and DRCF filters are disabled, the coefficient
memory cannot be read back, because the clock to the
coefficient RAM is also cut off.
In both microport and serial port operation, the DTACK
(RDY, SDO) and IRP pins are open-drain outputs and
should be terminated externally to VDDIO through a 1 kΩ
pull-up resistor.
3.3V
AD6654
3.3V
1kΩ
DTACK (RDY, SDO)
IRP
05156-056
1kΩ
Figure 75. DTACK, SDO, IRP Pull-Up Resistor Circuit
A simple RC circuit is used on the EXT_FILTER pin to
balance the internal RC circuit on this pin and maintain a
good PLL clock lock. The recommended circuit is given in
Figure 76. It is further recommended that this RC circuit be
placed as close as possible to the AD6654 part. This layout
consideration ensures that the PLL clock is clean and the
PLL lock is closely maintained.
VDD CORE
0.01µF
250Ω
EXT_FILTER
AD6654
05156-057
•
Figure 76. EXT_FILTER Circuit for PLL Clock
Rev. 0 | Page 85 of 88
AD6654
•
•
In the Intel mode microport, the beginning of a read and
write access is indicated by the RDY pin going low. The
access is complete only when the RDY pin goes high. In the
Motorola mode microport, the completion of a read and
write access is indicated by the DTACK pin going low. In
both modes, CS, RD (DS), and WR (R/W) should be active
until access is complete; otherwise, an incomplete access
results.
In both Intel and Motorola modes, if CS is held low even
after microport read or write access is complete, the
microport initiates a second access. This is a problem while
writing or reading from coefficient RAM, where each access
writes to or reads from a different RAM address. This can
be fixed by writing to one coefficient RAM address at a
time, that is, the coefficient start and stop address registers
have the same value.
•
In SPI mode programming, the SCS pin must go high
(inactive) after writing or reading each byte (eight clock
cycles on the SCLK pin).
Rev. 0 | Page 86 of 88
AD6654
OUTLINE DIMENSIONS
A1 CORNER
INDEX AREA
17.20
17.00 SQ
16.80
BALL A1
CORNER
16
13
12
11
10
9
8
7
6
5
4
3
2
1
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
15.00
BSC SQ
TOP VIEW
*1.85
1.71
1.40
15
14
1.00
BSC
BOTTOM VIEW
DETAIL A
DETAIL A
*1.31
1.21
1.10
*0.30 MIN
SEATING
PLANE
0.70
COPLANARITY
0.60
0.20
0.50
BALL DIAMETER
COMPLIANT TO JEDEC STANDARDS MO-192-AAF-1
EXCEPT FOR DIMENSIONS INDICATED BY A "*" SYMBOL.
Figure 77. 256-Lead Chip Scale Package Ball Grid Array [CSPBGA]
(BC-256-2)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD6654BBC
AD6654BBCZ1
AD6654CBC
AD6654CBCZ1
AD6654/PCB
1
Temperature Range
−25°C to +85°C
−25°C to +85°C
−25°C to +85°C
−25°C to +85°C
Active
Channels
6
6
4
4
6
Package Description
256-Lead CSPBGA (Ball Grid Array)
256-Lead CSPBGA (Ball Grid Array)
256-Lead CSPBGA (Ball Grid Array)
256-Lead CSPBGA (Ball Grid Array)
Evaluation Board with AD6654 and Software
Z = Pb-free part.
Rev. 0 | Page 87 of 88
Package Option
BC-256-2
BC-256-2
BC-256-2
BC-256-2
AD6654
NOTES
©2005 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05156–0–4/05(0)
Rev. 0 | Page 88 of 88