EGP10A THRU EGP10K Shanghai Lunsure Electronic Technology Co.,Ltd Tel:0086-21-37185008 Fax:0086-21-57152769 Features • • • • 1.0 Amp Glass Passivated High Efficient Rectifiers 50 to 800 Volts Superfast recovery time for high efficiency Glass passivated cavity-free junction, Plastic Case Low forward voltage, high current capability Low leakage current Maximum Ratings • • • DO-41 Operating Temperature: -55OC to +150 OC Storage Temperature: -55OC to +150 OC Typical Thermal Resistance: 50OC/W Junction to Ambient Part Number EGP10A EGP10B EGP10D EGP10F EGP10G EGP10J EGP10K Maximum Recurrent Peak Reverse Voltage 50V 100V 200V 300V 400V 600V 800V Maximum RMS Voltage Maximum DC Blocking Voltage 35V 70V 140V 210V 280V 420V 560V 50V 100V 200V 300V 400V 600V 800V D A Cathode Mark B Electrical Characteristics @ 25 C Unless Otherwise Specified O Average Forward Current Peak Forward Surge Current Maximum Instantaneous Forward Voltage EGP10A-10D EGP10F-10G EGP10J -10K Maximum DC Reverse Current At Rated DC Blocking Voltage Maximum Reverse Recovery Time EGP10A-10G EGP10J-10K Typical Junction Capacitance EGP10A-10D EGP10F-10K IF(AV) 1.0 A TA = 55OC IFSM 30A 8.3ms, half sine VF 0.95V 1.25V 1.70V IR 5.0uA 100uA trr 50nS 75nS CJ 22pF 15pF D C IF=1.0A TA=25OC DIMENSIONS O TA = 25 C TA = 125OC IF=0.5A, IR=1.0A, IRR=0.25A TJ=25OC DIM A B C D INCHES MIN .166 .080 .028 1.000 Measured at 1.0MHz, VR=4.0V www.cnelectr.com MAX .205 .107 .034 --- MM MIN 4.10 2.00 .70 25.40 MAX 5.20 2.70 .90 --- NOTE EGP10A thru EGP10K Figure 1 Typical For ward Characteristics 20 Figure 2 Forward Derating Curve 10 1.2 6 4 1.0 25OC 2 Amps .8 1 .6 150OC .6 Amps .4 .4 .2 .2 .1 Resistive or Inductive Load 0.375”(9.5mm) Lead Length .06 0 .04 0 50 75 EGP10A -EGP10D EGP10F-EGP10K 100 .4 .6 .8 1.0 1.2 1.4 Figure 3 Junction Capacitance 100 TJ =25OC 60 40 20 10 6 4 EGP10A -EGP10D EGP10F - EGP10K 2 1 .1 .2 .4 1 175 Average Forward Rectified Current - Amperes versus Ambient Temperature - OC Volts Instantaneous Forward Current - Amperes versus Instantaneous Forward Voltage - Volts pF 150 C .02 .01 125 O 2 4 10 Volts 20 40 100 200 Junction Capacitance - pF versus Reverse Voltage - Volts www.cnelectr.com 400 1000 EGP10A thru EGP10K Figure 4 Peak Forward Surge Current 60 50 40 30 Amps 20 10 0 1 2 4 6 8 10 20 40 60 80 100 Cycles Peak Forward Surge Current - Amperes versus Number Of Cycles At 60Hz - Cycles Figure 5 Reverse Recovery Time Characteristic And Test Circuit Diagram 50Ω 10Ω trr +0.5A 0 Pulse Generator Note 2 25Vdc 1Ω Notes: 1. Rise Time = 7ns max. Input impedance = 1 megohm, 22pF 2. Rise Time = 10ns max. Source impedance = 50 ohms 3. Resistors are non-inductive Oscilloscope Note 1 -0.25 -1.0 1cm Set Time Base for 20/100ns/cm www.cnelectr.com