AZ AZ8462 MICROMINIATURE POLARIZED RELAY FEATURES • SMT and DIP mounting available • Microminiature size: up to 50% less board area than previous generation telecom relays • High dielectric and surge voltage: 2.5 KV surge (per Bellcore TA–NWT–001089) 1.5 KV surge (per FCC Part 68) 1,000 Vrms, open contacts • Monostable and bistable (latching) versions available • Low power consumption: 79 mW pickup • Stable contact resistance for low level signal switching • Epoxy sealed for automatic wave soldering and cleaning • UL, CUR file E43203 • All plastics meet UL94 V–0, 30 min. oxygen index CONTACTS Arrangement DPDT (2 Form C) Bifurcated crossbar contacts Ratings Resistive load: Max. switched power: 60 W or 62.5 VA Max. switched current: 2.0 A Max. switched voltage: 220 VDC or 250 VAC Rated Load UL/CUR 0.5 A at 125 VAC general use 2.0 A at 30 VDC Material Silver nickel, gold plated Resistance < 50 milliohms initially at 6 V, 1 A COIL (Polarized) Power At Pickup Voltage (typical) 79 mW (3–24 VDC) 152 mW (48 VDC) GENERAL DATA Life Expectancy Mechanical Electrical Minimum operations 1 x 108 at 3Hz 1 x 105 at 0.5 A, 125 VAC, Res. 1 x 105 at 2.0 A, 30 VDC, Res. Operate Time (max) 4 ms at nominal coil voltage Release Time (max) 4 ms at nominal coil voltage (with no coil suppression) Dielectric Strength (at sea level) See table Dropout Greater than 10% of nominal coil voltage Insulation Resistance 109 ohms min. at 25°C, 500 VDC, 50% RH Ambient Temperature Operating Storage At nominal coil voltage -40°C (-40°F) to 85°C (185°F) -40°C (-40°F) to 115°C (239°F) Vibration Operational, 3.3 mm DA, 10–55 Hz Non-destructive, 5.5 mm DA, 10–55 Hz Shock Operational, 75 g min., 11 ms Non-destructive, 100 g min., 11 ms Max. Solder Temp. 260°C (500°F) for 5 seconds Max. Solvent Temp. 80°C (176°F) Max. Immersion Time 30 seconds Weight 2 grams Enclosure P.B.T. polyester Terminals Tinned copper alloy, P.C. Max. Continuous Dissipation 0.32 W at 20°C (68°F) Temperature Rise At 30° C (54°F) nominal coil voltage 1. All values at 20°C (68°F). Max. 115°C (239°F) 2. Relay may pull in with less than “Must Operate” value. Temperature NOTES 3. Relay has fixed coil polarity. 4. Specifications subject to change without notice. 4/16/09W AZ AZ8462 RELAY ORDERING DATA STANDARD VERSION Nominal Coil VDC 1.5 3 ORDER NUMBER Must Operate VDC 1.13 Max. Continuous VDC 2.2 2.25 4.5 Coil Resistance ± 10% 16.1 64.3 THT (Through Hole) SMT* AZ8462–1.5 AZ8462S–1.5 AZ8462–3 AZ8462S–3 4.5 3.38 6.7 145 AZ8462–4.5 AZ8462S–4.5 5 3.75 7.5 178 AZ8462–5 AZ8462S–5 6 4.50 9 257 AZ8462–6 AZ8462S–6 9 6.75 13.5 579 AZ8462–9 AZ8462S–9 12 9.00 18 1028 AZ8462–12 AZ8462S–12 24 18.00 36 4114 AZ8462–24 AZ8462S–24 48 36.0 57.6 8533 AZ8462-48 AZ8462S–48 SINGLE COIL LATCHING VERSION Nominal Coil VDC 1.5 3 Set/Reset Voltage 1.13 Max. Continuous VDC 2.7 2.25 5.4 Coil Resistance ± 10% 22.5 90 THT (Through Hole) SMT* AZ8462P1–1.5 AZ8462P1S–1.5 AZ8462P1–3 AZ8462P1S–3 4.5 3.38 8.1 203 AZ8462P1–4.5 AZ8462P1S–4.5 5 3.75 9.0 250 AZ8462P1–5 AZ8462P1S–5 6 4.50 10.8 360 AZ8462P1–6 AZ8462P1S–6 9 6.75 16.2 810 AZ8462P1–9 AZ8462P1S–9 12 9.00 21.6 1440 AZ8462P1–12 AZ8462P1S–12 24 18.00 43.2 5760 AZ8462P1–24 AZ8462P1S–24 DUAL COIL LATCHING VERSION Nominal Coil VDC 1.5 Set/Reset Voltage 1.13 Max. Continuous VDC 2.2 Coil Resistance ± 10% 11.2 THT (Through Hole) SMT* AZ8462P2–1.5 AZ8462P2S–1.5 AZ8462P2–3 AZ8462P2S–3 101 AZ8462P2–4.5 AZ8462P2S–4.5 7.5 125 AZ8462P2–5 AZ8462P2S–5 9.0 180 AZ8462P2–6 AZ8462P2S–6 13.5 405 AZ8462P2–9 AZ8462P2S–9 3 2.25 4.5 45 4.5 3.38 6.7 5 3.75 6 4.50 9 6.75 12 9.00 18.0 720 AZ8462P2–12 AZ8462P2S–12 24 18.00 36.0 2280 AZ8462P2–24 AZ8462P2S–24 *For Tape and Reel add suffix “TR.” For SMT short leg add “1” after S. INITIAL DIELECTRIC STRENGTH (minimum) Between open contacts VRMS, 1 min. 1,000 SURGE Peak (V) 1,500 Rise Time (µS) 10 Decay Time* (9µS) (1/2 peak) 160 Between contact sets 1,000 - - - Between coil and contacts 1,500 2,500 2 10 * Decay time measured from beginning of surge. 4/16/09W AZ8462 Outline Dimensions(DIP type) Viewed Toward Terminals SINGLE SIDE STABLE & 1 COIL LATCHING .598MAX [15.20] 2 COIL LATCHING .598MAX [15.20] .303MAX [7.70] .362MAX [9.20] .024 [0.60] PC Board Layout (DIP type) .200 [5.08] .303MAX [7.70] .100 [2.54] .200 [5.08] .362MAX [9.20] .024 [0.60] .130 [3.30] .045 [1.15] 8-Ø0.039 [Ø1.00] .130 [3.30] SINGLE SIDE STABLE & 1 COIL LATCHING .045 [1.15] .100 .200 [5.08] [2.54] .200 .100 [5.08] [2.54] .200 [5.08] .100 [2.54] .200 [5.08] .200 [5.08] .200 [5.08] Outline Dimensions(SMT Type ) 2 COIL LATCHING SINGLE SIDE STABLE & 1 COIL LATCHING .598MAX [15.20] 2 COIL LATCHING PC Board Layout (SMT type) .598MAX [15.20] .303MAX [7.70] .362MAX [9.20] .024 [0.60] .045 [1.15] .303MAX [7.70] .024 [0.60] .045 [1.15] .200 [5.08] .374MAX [9.50] .200 .100 [5.08] [2.54] .039 [1.00] .200 [5.08] .100 [2.54] .122 [3.11] .362MAX [9.20] .382MAX [9.70] .020 [0.50] 10-Ø0.039 [Ø1.00] .382MAX [9.70] .283 [7.19] .200 [5.08] .374MAX [9.50] .200 .100 [5.08] [2.54] SINGLE SIDE STABLE & 1 COIL LATCHING .039 [1.00] .200 [5.08] .100 [2.54] 0.122 [3.11] .283 [7.19] Outline Dimensions(S1 type: Short SMT) SINGLE SIDE STABLE & 1 COIL LATCHING 2 COIL LATCHING 2 COIL LATCHING .598MAX [15.20] .598MAX [15.20] .303MAX [7.70] .303MAX [7.70] PC Board Layout (Type S : Short SMT) .362MAX [9.20] .024 [0.60] .045 [1.15] .382MAX [9.70] .024 [0.60] .045 [1.15] .200 [5.08] .374MAX [7.50] .020 [0.50] .200 .100 [5.08] [2.54] .039 [1.00] .362MAX [9.20] .200 [5.08] .100 [2.54] .382MAX [9.70] .122 [2.21] .200 [5.08] .374MAX [7.50] .200 .100 [5.08] [2.54] .247 [6.29] SINGLE SIDE STABLE & 1 COIL LATCHING .039 [1.00] Wiring Diagram .200 [5.08] .100 [2.54] Viewed Toward Terminals 0.122 [2.21] - 12 10 9 8 SINGLE SIDE STABLE 4 - + 12 +1 5 3 4 5 6+ 10 9 8 1 COIL LATCHING .247 [6.29] RESET 3 + 1- 5 SET 4 SET 3 RESET + 1 - 12 10 9 8 7 2 COIL LATCHING - 2 COIL LATCHING Dimensions in inch with millimeters in brackets below. Tolerance: ± .010” 4/16/09W