TI1 INA301A3QDGKTQ1 Current-shunt monitor with high-speed, overcurrent protection comparator Datasheet

Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
INA301-Q1
SBOS786A – APRIL 2016 – REVISED JUNE 2016
INA301-Q1 36-V, Automotive, High-Speed, Zero-Drift, Voltage-Output
Current-Shunt Monitor With High-Speed, Overcurrent Protection Comparator
1 Features
3 Description
•
•
The INA301-Q1 includes both a high common-mode,
current-sensing
amplifier
and
a
high-speed
comparator configured to provide overcurrent
protection by measuring the voltage developed
across a current-sensing or current-shunt resistor and
comparing that voltage to a defined threshold limit.
This device features an adjustable limit-threshold
range that is set using a single external limit-setting
resistor. This current-shunt monitor measures
differential voltage signals on common-mode voltages
that can vary from 0 V up to 36 V, independent of the
supply voltage.
1
•
•
•
•
•
•
•
•
Qualified for Automotive Applications
AEC-Q100 Qualified With the Following Results:
– Device Temperature Grade 1: –40°C to
+125°C Ambient Operating Temperature
– Device HBM ESD Classification Level 2
– Device CDM ESD Classification Level C6
Wide Common-Mode Input Range: 0 V to 36 V
Dual Output: Amplifier and Comparator Output
High Accuracy Amplifier:
– Offset Voltage: 35 µV (Max)
– Offset Voltage Drift: 0.5 µV/°C (Max)
– Gain Error: 0.1% (Max)
– Gain Error Drift: 10 ppm/°C
Available Amplifier Gains:
– INA301A1-Q1: 20 V/V
– INA301A2-Q1: 50 V/V
– INA301A3-Q1: 100 V/V
Programmable Alert Threshold Set Through a
Single Resistor
Total Alert Response Time: 1 µs
Open-Drain Output With Both Transparent and
Latching Modes
Package: VSSOP-8
2 Applications
•
•
•
•
•
•
•
•
•
Solenoid Control
Low-Side Motor Monitoring
Electronic Power Steering
Power Seats
Power Windows
Body Control Modules
Electronic Control Units
Overcurrent Protection
eFuses
The open-drain alert output can be configured to
operate in either a transparent mode, where the
output status follows the input state, or in a latched
mode, where the alert output is cleared when the
latch is reset. The device alert response time is under
1 µs, allowing for quick detection of overcurrent
events.
This device operates from a single 2.7-V to 5.5-V
supply, drawing a maximum supply current of 700 µA.
The device is specified over the extended operating
temperature range of –40°C to +125°C, and is
available in an 8-pin VSSOP package.
Device Information(1)
PART NUMBER
PACKAGE
INA301-Q1
BODY SIZE (NOM)
VSSOP (8)
3.00 mm × 3.00 mm
(1) For all available packages, see the package option addendum
at the end of the data sheet.
Typical Application
CBYPASS
0.1 F
2.7 V to 5.5 V
Supply
(0 V to 36 V)
VS
IN+
+
INA301-Q1
RPULL-UP
10 k
Microcontroller
OUT
ADC
ALERT
IN±
Load
GPIO
RESET
GPIO
LIMIT
DAC
GND
RLIMIT
Copyright © 2016, Texas Instruments Incorporated
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
INA301-Q1
SBOS786A – APRIL 2016 – REVISED JUNE 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
4
4
4
4
5
7
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
Detailed Description ............................................ 13
7.1 Overview ................................................................. 13
7.2 Functional Block Diagram ....................................... 13
7.3 Feature Description................................................. 14
7.4 Device Functional Modes........................................ 16
8
Applications and Implementation ...................... 18
8.1 Application Information .......................................... 18
8.2 Typical Application .................................................. 22
9 Power Supply Recommendations...................... 24
10 Layout................................................................... 24
10.1 Layout Guidelines ................................................. 24
10.2 Layout Example .................................................... 24
11 Device and Documentation Support ................. 25
11.1
11.2
11.3
11.4
11.5
11.6
Documentation Support ........................................
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
25
25
25
25
25
25
12 Mechanical, Packaging, and Orderable
Information ........................................................... 25
4 Revision History
Changes from Original (April 2016) to Revision A
•
2
Page
Changed from product preview to production data ................................................................................................................ 1
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: INA301-Q1
INA301-Q1
www.ti.com
SBOS786A – APRIL 2016 – REVISED JUNE 2016
5 Pin Configuration and Functions
DGK Package
8-Pin VSSOP
Top View
VS
1
8
IN+
OUT
2
7
IN±
LIMIT
3
6
ALERT
GND
4
5
RESET
Not to scale
Pin Functions
PIN
NO.
NAME
I/O
1
VS
Analog
2
OUT
Analog output
3
LIMIT
Analog input
DESCRIPTION
Power supply, 2.7 V to 5.5 V
Output voltage
Alert threshold limit input; see the Current-Limit Threshold section for details on
setting the limit threshold.
4
GND
Analog
5
RESET
Digital input
Ground
6
ALERT
Digital output
Overlimit alert, active-low, open-drain output
7
IN–
Analog input
Negative voltage input. Connect to load side of the shunt resistor.
8
IN+
Analog input
Positive voltage input. Connect to supply side of the shunt resistor.
Transparent or latch mode selection input
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: INA301-Q1
3
INA301-Q1
SBOS786A – APRIL 2016 – REVISED JUNE 2016
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1)
MIN
Supply voltage, VS
Differential (VIN+) – (VIN–)
(2)
MAX
UNIT
6
V
–40
40
Common-mode (3)
GND – 0.3
40
Analog input
LIMIT pin
GND – 0.3
(VS) + 0.3
V
Analog output
OUT pin
GND – 0.3
(VS) + 0.3
V
Digital input
RESET pin
GND – 0.3
(VS) + 0.3
V
Digital output
ALERT pin
GND – 0.3
6
V
–55
150
°C
150
°C
150
°C
Analog inputs (IN+, IN–)
Operating temperature, TA
Junction temperature, TJ
Storage temperature, Tstg
(1)
(2)
(3)
–65
V
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
VIN+ and VIN– are the voltages at the IN+ and IN– pins, respectively.
Input voltage can exceed the voltage shown without causing damage to the device if the current at that pin is limited to 5 mA.
6.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001
Electrostatic discharge
(1)
UNIT
±2000
Charged-device model (CDM), per JEDEC specification JESD22-C101 (2)
V
±1000
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
VCM
Common-mode input voltage
VS
Operating supply voltage
2.7
TA
Operating free-air temperature
–40
NOM
MAX
12
UNIT
V
5
5.5
V
125
°C
6.4 Thermal Information
INA301-Q1
THERMAL METRIC (1)
DGK (VSSOP)
UNIT
8 PINS
RθJA
Junction-to-ambient thermal resistance
161.5
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
62.3
°C/W
RθJB
Junction-to-board thermal resistance
81.4
°C/W
ψJT
Junction-to-top characterization parameter
6.8
°C/W
ψJB
Junction-to-board characterization parameter
80
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
°C/W
(1)
4
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: INA301-Q1
INA301-Q1
www.ti.com
SBOS786A – APRIL 2016 – REVISED JUNE 2016
6.5 Electrical Characteristics
at TA = 25°C, VSENSE = VIN+ – VIN– = 10 mV, VS = 5 V, VIN+ = 12 V, and VLIMIT = 2 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
INPUT
VCM
Common-mode input voltage range
VIN
Differential input voltage range
CMR
Common-mode rejection
0
36
VIN = VIN+ – VIN–, INA301A1-Q1
0
250
VIN = VIN+ – VIN–, INA301A2-Q1
0
100
VIN = VIN+ – VIN–, INA301A3-Q1
0
50
INA301A1-Q1, VIN+ = 0 V to 36 V,
TA = –40ºC to +125ºC
100
110
INA301A2-Q1, VIN+ = 0 V to 36 V,
TA = –40ºC to +125ºC
106
118
INA301A3-Q1, VIN+ = 0 V to 36 V,
TA = –40ºC to +125ºC
110
120
V
mV
dB
INA301A1-Q1
±25
±125
INA301A2-Q1
±15
±50
INA301A3-Q1
±10
±35
TA= –40ºC to +125ºC
0.1
0.5
µV/°C
±0.1
±10
µV/V
VOS
Offset voltage, RTI (1)
dVOS/dT
Offset voltage drift, RTI (1)
PSRR
Power-supply rejection ratio
VS = 2.7 V to 5.5 V, VIN+ = 12 V,
TA = –40ºC to +125ºC
IB
Input bias current
IB+, IB–
120
µA
IOS
Input offset current
VSENSE = 0 mV
±0.1
µA
µV
OUTPUT
INA301A1-Q1
G
Gain
Gain error
20
INA301A2-Q1
50
INA301A3-Q1
100
V/V
INA301A1-Q1, VOUT = 0.5 V to VS – 0.5 V
±0.03%
±0.1%
INA301A2-Q1, VOUT = 0.5 V to VS – 0.5 V
±0.05%
±0.15%
INA301A3-Q1, VOUT = 0.5 V to VS – 0.5 V
±0.11%
±0.2%
3
10
TA= –40ºC to 125ºC
Nonlinearity error
VOUT = 0.5 V to VS – 0.5 V
Maximum capacitive load
No sustained oscillation
ppm/°C
±0.01%
500
pF
VOLTAGE OUTPUT
Swing to VS power-supply rail
RL = 10 kΩ to GND,
TA = –40ºC to +125ºC
VS – 0.05
VS – 0.1
Swing to GND
RL = 10 kΩ to GND,
TA = –40ºC to +125ºC
VGND + 20
VGND + 30
V
mV
FREQUENCY RESPONSE
BW
Bandwidth
SR
INA301A1-Q1
550
INA301A2-Q1
500
INA301A3-Q1
450
Slew rate
kHz
4
V/µs
30
nV/√Hz
NOISE, RTI (1)
Voltage noise density
(1)
RTI = referred-to-input.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: INA301-Q1
5
INA301-Q1
SBOS786A – APRIL 2016 – REVISED JUNE 2016
www.ti.com
Electrical Characteristics (continued)
at TA = 25°C, VSENSE = VIN+ – VIN– = 10 mV, VS = 5 V, VIN+ = 12 V, and VLIMIT = 2 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
COMPARATOR
tp
Total alert propagation delay
Input overdrive = 1 mV
Slew-rate-limited tp
VOUT step = 0.5 V to 4.5 V, VLIMIT = 4 V
ILIMIT
Limit threshold output current
VOS
Comparator offset voltage
VHYS
Hysteresis
TA = 25ºC
79.7
TA = –40ºC to +125ºC
79.2
0.75
1
1
1.5
80
80.3
80.8
INA301A1-Q1
1
INA301A2-Q1
1
4
INA301A3-Q1
1.5
4.5
INA301A1-Q1
20
INA301A2-Q1
50
INA301A3-Q1
100
µs
µA
3.5
mV
mV
VIH
High-level input voltage
1.4
6
VIL
Low-level input voltage
0
0.4
V
V
VOL
Alert low-level output voltage
IOL = 3 mA
70
300
mV
ALERT pin leakage input current
VOH = 3.3 V
0.1
1
µA
Digital leakage input current
0 ≤ VIN ≤ VS
1
µA
POWER SUPPLY
IQ
6
Quiescent current
VSENSE = 0 mV, TA = 25ºC
TA = –40ºC to +125ºC
Submit Documentation Feedback
500
650
700
µA
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: INA301-Q1
INA301-Q1
www.ti.com
SBOS786A – APRIL 2016 – REVISED JUNE 2016
6.6 Typical Characteristics
Input Offset Voltage (PV)
100
80
60
40
20
0
-20
-40
-60
-100
-80
Population
100
80
60
40
20
0
-20
-40
-60
-80
-100
Population
at TA = 25°C, VS = 5 V, VIN+ = 12 V, and alert pullup resistor = 10 kΩ (unless otherwise noted)
Input Offset Voltage (PV)
Figure 1. Input Offset Voltage Distribution (INA301A1-Q1)
Figure 2. Input Offset Voltage Distribution (INA301A2-Q1)
60
INA301A1-Q1
INA301A2-Q1
INA301A3-Q1
Population
Offset Voltage (µV)
40
20
100
80
60
40
20
0
-20
-40
-60
-80
-100
0
-20
-50
-25
0
25
50
75
Temperature (°C)
100
125
150
Input Offset Voltage (PV)
Figure 4. Input Offset Voltage vs Temperature
5
4
3
2
1
0
-1
-2
-3
-4
-5
10
8
6
4
2
0
-2
-4
-6
-8
-10
Population
Population
Figure 3. Input Offset Voltage Distribution (INA301A3-Q1)
CMRR (PV/V)
CMRR (PV/V)
Figure 5. Common-Mode Rejection Ratio Distribution
(INA301A1-Q1)
Figure 6. Common-Mode Rejection Ratio Distribution
(INA301A2-Q1)
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: INA301-Q1
7
INA301-Q1
SBOS786A – APRIL 2016 – REVISED JUNE 2016
www.ti.com
Typical Characteristics (continued)
at TA = 25°C, VS = 5 V, VIN+ = 12 V, and alert pullup resistor = 10 kΩ (unless otherwise noted)
2.5
2
INA301A1-Q1
INA301A2-Q1
INA301A3-Q1
1.5
1
0.5
0
-0.5
-1
-50
3
2.5
2
1.5
1
0
0.5
-1
-0.5
-1.5
-2
-2.5
-3
Population
Common-Mode Rejection Ratio (µV/V)
3
-25
0
25
50
75
Temperature (°C)
100
125
150
CMRR (PV/V)
Figure 7. Common-Mode Rejection Ratio Distribution
(INA301A3-Q1)
Figure 8. Common-Mode Rejection Ratio vs Temperature
INA301A1-Q1
INA301A2-Q1
INA301A3-Q1
120
Population
100
0.1
0.08
0.06
0.04
0.02
1M
0
100k
-0.02
1k
10k
Frequency (Hz)
-0.04
100
-0.06
60
10
-0.08
80
-0.1
Common-Mode Rejection Ratio (dB)
140
Gain Error (%)
Figure 10. Gain Error Distribution (INA301A1-Q1)
Gain Error (%)
0.2
0.16
0.12
0.08
0.04
0
-0.04
-0.08
-0.12
Gain Error (%)
Figure 11. Gain Error Distribution (INA301A2-Q1)
8
-0.16
-0.2
Population
0.1
0.08
0.06
0.04
0.02
0
-0.02
-0.04
-0.06
-0.08
-0.1
Population
Figure 9. Common-Mode Rejection Ratio vs Frequency
Figure 12. Gain Error Distribution (INA301A3-Q1)
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: INA301-Q1
INA301-Q1
www.ti.com
SBOS786A – APRIL 2016 – REVISED JUNE 2016
Typical Characteristics (continued)
at TA = 25°C, VS = 5 V, VIN+ = 12 V, and alert pullup resistor = 10 kΩ (unless otherwise noted)
0.5
50
INA301A1-Q1
INA301A2-Q1
INA301A3-Q1
0.4
0.3
40
30
0.1
Gain (dB)
Gain Error (%)
0.2
0
-0.1
-0.2
20
10
0
-0.3
INA301A1-Q1
INA301A2-Q1
INA301A3-Q1
-10
-0.4
-0.5
-50
-20
-25
0
25
50
75
Temperature (°C)
100
125
150
1
10
Figure 13. Gain Error vs Temperature
1k
10k
Frequency (Hz)
100k
1M
10M
Figure 14. Gain vs Frequency
VS
140
Output Voltage Swing (V)
120
100
PSRR (dB)
100
80
60
VS - 1
VS - 2
GND + 3
GND + 2
125ºC
25ºC
-40ºC
GND + 1
40
GND
20
1
10
100
1k
10k
Frequency (Hz)
100k
1M
0
10M
4
6
8
10
12
14
Output Current (mA)
Figure 16. Output Voltage Swing vs Output Current
Figure 15. Power-Supply Rejection Ratio vs Frequency
150
250
200
120
Input Bias Current (PA)
Input Bias Current (PA)
2
150
100
50
90
60
30
0
-50
0
0
5
10
15
20
25
30
Common-Mode Voltage (V)
35
40
0
VS = 5 V
5
10
15
20
25
30
Common-Mode Voltage (V)
35
40
VS = 0 V
Figure 17. Input Bias Current vs Common-Mode Voltage
Figure 18. Input Bias Current vs Common-Mode Voltage
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: INA301-Q1
9
INA301-Q1
SBOS786A – APRIL 2016 – REVISED JUNE 2016
www.ti.com
Typical Characteristics (continued)
at TA = 25°C, VS = 5 V, VIN+ = 12 V, and alert pullup resistor = 10 kΩ (unless otherwise noted)
145
600
140
Quiescent Current (PA)
Input Bias Current (PA)
550
135
130
125
120
115
110
500
450
400
350
105
100
-50
-25
0
25
50
75
Temperature (qC)
100
125
300
2.7
150
Figure 19. Input Bias Current vs Temperature
3.6
3.9 4.2 4.5 4.8
Supply Voltage (V)
5.1
5.4
5.7
Input-Referred Voltage Noise (nV/Ö Hz)
35
520
Quiescent Current (PA)
3.3
Figure 20. Quiescent Current vs Supply Voltage
540
500
480
460
440
420
-50
3
30
25
20
15
10
INA301A1-Q1
INA301A2-Q1
INA301A3-Q1
5
0
-25
0
25
50
75
Temperature (qC)
100
125
150
1
Figure 21. Quiescent Current vs Temperature
10
100
1k
10k
Frequency (Hz)
1M
Input (200 mV/div)
Figure 22. Input-Referred Voltage Noise vs Frequency
Input
Output
Output (1 V/div)
Referred-to-Input Voltage Noise
(200 nV/div)
100k
Time (1 s/div)
Time (1 Ps/div)
4-VPP output step
Figure 23. 0.1-Hz to 10-Hz Referred-to-Input Voltage Noise
10
Figure 24. Voltage Output Rising Step Response
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: INA301-Q1
INA301-Q1
www.ti.com
SBOS786A – APRIL 2016 – REVISED JUNE 2016
Typical Characteristics (continued)
VOUT (60 mV/div)
Output (1 V/div)
Input
Output
Common-Mode Voltage (10 V/div)
Input (200 mV/div)
at TA = 25°C, VS = 5 V, VIN+ = 12 V, and alert pullup resistor = 10 kΩ (unless otherwise noted)
VCM
VOUT
Time (1 Ps/div)
Time (2 Ps/div)
4-VPP output step
Figure 25. Voltage Output Falling Step Response
Figure 26. Common-Mode Voltage Transient Response
80.8
Voltage (2 V/div)
Limit Current Source (PA)
80.6
VSUPPLY
VOUT
80.4
80.2
80
79.8
79.6
79.4
79.2
-50
Time (5 Ps/div)
0
25
50
75
Temperature (qC)
100
125
150
Figure 28. Limit Current Source vs Temperature
VIN * 20 V/V
Alert
VLIMIT
Voltage (0.5 V/div)
Figure 27. Start-Up Response
Voltage (0.5 V/div)
-25
VIN * 50 V/V
Alert
VLIMIT
Time (200 ns/div)
Time (200 ns/div)
Figure 29. Total Propagation Delay (INA301A1-Q1)
Figure 30. Total Propagation Delay (INA301A2-Q1)
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: INA301-Q1
11
INA301-Q1
SBOS786A – APRIL 2016 – REVISED JUNE 2016
www.ti.com
Typical Characteristics (continued)
at TA = 25°C, VS = 5 V, VIN+ = 12 V, and alert pullup resistor = 10 kΩ (unless otherwise noted)
1,000
Propagation Delay (ns)
Voltage (0.5 V/div)
800
VIN * 100 V/V
Alert
VLIMIT
600
400
200
0
-50
Time (200 ns/div)
-25
0
25
50
75
Temperature (qC)
100
125
150
VOD = 1 mV
Figure 32. Comparator Propagation Delay vs Temperature
120
100
100
80
80
Hysteresis (mV)
Low-Level Output Voltage (mV)
Figure 31. Total Propagation Delay (INA301A3-Q1)
120
60
40
20
INA301A1-Q1
INA301A2-Q1
INA301A3-Q1
60
40
20
0
0
0.5
1
1.5
2
2.5
3
3.5
4
Low-Level Output Current (mA)
4.5
0
-50
5
Figure 33. Comparator Alert VOL vs IOL
-25
0
25
50
75
Temperature (°C)
100
125
150
Figure 34. Hysteresis vs Temperature
Voltage (2 V/div)
Reset
Alert
Time (2 Ps/div)
Figure 35. Comparator Reset Response
12
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: INA301-Q1
INA301-Q1
www.ti.com
SBOS786A – APRIL 2016 – REVISED JUNE 2016
7 Detailed Description
7.1 Overview
The INA301-Q1 is a 36-V common-mode, zero-drift topology, current-sensing amplifier that can be used in both
low-side and high-side configurations. These specially-designed, current-sensing amplifiers are able to accurately
measure voltages developed across current-sensing resistors (also known as current-shunt resistors) on
common-mode voltages that far exceed the supply voltage powering the device. Current can be measured on
input voltage rails as high as 36 V, and the device can be powered from supply voltages as low as 2.7 V. The
device can also withstand the full 36-V common-mode voltage at the input pins when the supply voltage is
removed without causing damage.
The zero-drift topology enables high-precision measurements with maximum input offset voltages as low as
35 μV with a temperature contribution of only 0.5 μV/°C over the full temperature range of –40°C to +125°C. The
low total offset voltage of the INA301-Q1 enables smaller current-sense resistor values to be used, and allows for
a more efficient system operation without sacrificing measurement accuracy resulting from the smaller input
signal.
The INA301-Q1 uses a single external resistor to allow for a simple method of setting the corresponding current
threshold level for the device to use for out-of-range comparison. Combining the precision measurement of the
current-sense amplifier and the onboard comparator enables an all-in-one overcurrent detection device. This
combination creates a highly-accurate solution that is capable of fast detection of out-of-range conditions, and
allows the system to take corrective actions to prevent potential component or system-wide damage.
7.2 Functional Block Diagram
CBYPASS
0.1 F
2.7 V to 5.5 V
Power Supply
(0 V to 36 V)
VS
IN+
INA301-Q1
RPULL-UP
10 k
+
OUT
Gain = 20, 50,
100
IN±
Load
ALERT
+
RESET
GND
LIMIT
RSET
Copyright © 2016, Texas Instruments Incorporated
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: INA301-Q1
13
INA301-Q1
SBOS786A – APRIL 2016 – REVISED JUNE 2016
www.ti.com
7.3 Feature Description
7.3.1 Alert Output (ALERT Pin)
The device ALERT pin is an active-low, open-drain output that is designed to be pulled low when the input
conditions are detected to be out-of-range. Add a 10-kΩ pullup resistor from ALERT pin to the supply voltage.
This open-drain pin can be pulled up to a voltage beyond the VS supply voltage, but must not exceed 5.5 V.
Figure 36 shows the alert output response of the internal comparator. When the output voltage of the amplifier is
less than the voltage developed at the LIMIT pin, the comparator output is in the default high state. When the
amplifier output voltage exceeds the threshold voltage set at the LIMIT pin, the comparator output becomes
active and pulls low. This active low output indicates that the measured signal at the amplifier input has
exceeded the programmed threshold level, indicating an overcurrent or out-of-range condition has occurred.
6
VOUT
VLIMIT
ALERT
5
Voltage (V)
4
3
2
1
0
±1
Time (5 ms/div)
C001
Figure 36. Overcurrent Alert Response
7.3.2 Current-Limit Threshold
The INA301-Q1 determines if an overcurrent event is present by comparing the amplified measured voltage
developed across the current-sensing resistor to the corresponding signal developed at the LIMIT pin. The
threshold voltage for the LIMIT pin is set using a single external resistor, or by connecting an external voltage
source to the LIMIT pin.
7.3.2.1 Resistor-Controlled Current Limit
The typical method for setting the limit threshold voltage is to connect a resistor from the LIMIT pin to ground.
The value of this resistor, RLIMIT, is chosen in order to create a corresponding voltage at the LIMIT pin equivalent
to the output voltage, VOUT, when the maximum desired load current is flowing through the current-sensing
resistor. An internal 80-µA current source is connected to the LIMIT pin to create a corresponding voltage used
to compare to the amplifier output voltage, depending on the value of the RLIMIT resistor.
In the equations from Table 1, VTRIP represents the overcurrent threshold that the device is programmed to
monitor, and VLIMIT is the programmed signal set to detect the VTRIP level.
Table 1. Calculating the Threshold-Limit-Setting Resistor, RLIMIT
PARAMETER
VTRIP
VOUT at the desired-current trip value
VLIMIT
Threshold limit voltage
RLIMIT
Threshold limit-setting resistor value
14
EQUATION
ILOAD × RSENSE x Gain
VLIMIT = VTRIP
ILIMIT × RLIMIT
VLIMIT / ILIMIT
VLIMIT / 80 µA
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: INA301-Q1
INA301-Q1
www.ti.com
SBOS786A – APRIL 2016 – REVISED JUNE 2016
7.3.2.1.1 Resistor-Controlled, Current-Limit Example
If the current level indicating an out-of-range condition is present is 20 A, and the current-sense resistor value is
10 mΩ, then the input threshold signal is 200 mV. The INA301A1-Q1 has a gain of 20, therefore, the resulting
output voltage at the 20-A input condition is 4 V. The value for RLIMIT is selected to allow the device to detect to
this 20-A threshold, indicating an overcurrent event occurred. When the INA301-Q1 detects this out-of-range
condition, the ALERT pin asserts and pulls low. For this example, to detect a 4-V level, the value of RLIMIT is
calculated to be 50 kΩ, as shown in Table 2.
Table 2. Example of Calculating the Limit Threshold Setting Resistor, RLIMIT
PARAMETER
VTRIP
VOUT at the desired current trip value
VLIMIT
Threshold limit voltage
RLIMIT
Threshold limit-setting resistor value
EQUATION
ILOAD × RSENSE x Gain
↓
20 A x 10 mΩ x 20 V/V = 4 V
VLIMIT = VTRIP
ILIMIT × RLIMIT
VLIMIT / ILIMIT
↓
4 V / 80 µA = 50 kΩ
7.3.2.2 Voltage-Source-Controlled Current Limit
Another method for setting the limit voltage is to connect the LIMIT pin to a programmable digital-to-analog
converter (DAC) or other external voltage source. The benefit of this method is the ability to adjust the currentlimit threshold to account for different threshold voltages that are used for different system operating conditions.
For example, this method can be used in a system that has one current-limit threshold level that must be
monitored during a power-up sequence, but different threshold levels that must be monitored during other system
operating modes.
In Table 3, VTRIP represents the overcurrent threshold that the device is programmed to monitor, and VSOURCE is
the programmed signal set to detect the VTRIP level.
Table 3. Calculating the Limit Threshold Voltage Source, VSOURCE
PARAMETER
EQUATION
VTRIP
VOUT at the desired current trip value
ILOAD × RSENSE × Gain
VSOURCE
Threshold limit voltage
VSOURCE = VTRIP
7.3.3 Hysteresis
The onboard comparator in the INA301-Q1 reduces the possibility of oscillations in the alert output when the
measured signal level is near the overlimit threshold level because of noise. When the output voltage (VOUT)
exceeds the voltage developed at the LIMIT pin, the ALERT pin is asserted and pulls low. The output voltage
must drop below the LIMIT pin threshold voltage by the gain-dependent hysteresis level in order for the ALERT
pin to deassert and return to the nominal high state, as shown in Figure 37.
ALERT
Alert
Output
VOUT
VLIMIT - Hysteresis
VLIMIT
Figure 37. Typical Comparator Hysteresis
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: INA301-Q1
15
INA301-Q1
SBOS786A – APRIL 2016 – REVISED JUNE 2016
www.ti.com
7.4 Device Functional Modes
7.4.1 Alert Mode
The device has two output operating modes, transparent and latched, that are selected based on the RESET pin
setting. These modes change how the ALERT pin responds following an alert when the overcurrent condition is
removed.
7.4.1.1 Transparent Output Mode
The device is set to transparent mode when the RESET pin is pulled low, thus allowing the output alert state to
change and follow the input signal with respect to the programmed alert threshold. For example, when the
differential input signal rises above the alert threshold, the ALERT output pin is pulled low. As soon as the
differential input signal drops below the alert threshold, the output returns to the default high-output state. A
common implementation using the device in transparent mode is to connect the ALERT pin to a hardware
interrupt input on a microcontroller. As soon as an overcurrent condition is detected and the ALERT pin is pulled
low, the hardware interrupt input detects the output-state change, and the microcontroller can begin to make
changes to the system operation required to address the overcurrent condition. Under this configuration, the
ALERT pin transition from high to low is captured by the microcontroller so that the output can return to the
default high state when the overcurrent event is removed.
7.4.1.2 Latch Output Mode
Some applications do not have the functionality available to continuously monitor the state of the output ALERT
pin to detect an overcurrent condition as described in the Transparent Output Mode section. A typical example of
this application is a system that is only able to poll the ALERT pin state periodically to determine if the system is
functioning correctly. If the device is set to transparent mode in this type of application, the state change of the
ALERT pin might be missed when ALERT is pulled low to indicate an out-of-range event, if the out-of-range
condition does not appear during one of these periodic polling events. Latch mode is specifically intended to
accommodate these applications.
The INA301-Q1 is placed into the corresponding output modes based on the signal connected to RESET, as
shown in Table 4. The difference between latch mode and transparent mode is how the ALERT pin responds
when an overcurrent event ends. In transparent mode (RESET = low), when the differential input signal drops
below the limit threshold level after the ALERT pin asserts because of an overcurrent event, the ALERT pin state
returns to the default high setting to indicate that the overcurrent event has ended.
Table 4. Output Mode Settings
OUTPUT MODE
RESET PIN SETTING
Transparent mode
RESET = low
Latch mode
RESET = high
In latch mode (RESET = high), when an overlimit condition is detected and the ALERT pin is pulled low, the
ALERT pin does not return to the default high state when the differential input signal drops below the alert
threshold level. In order to clear the alert, pull the RESET pin low for at least 100 ns. Pulling the RESET pin low
allows the ALERT pin to return to the default high level, provided that the differential input signal has dropped
below the alert threshold. If the input signal is still greater than the threshold limit when the RESET pin is pulled
low, the ALERT pin remains low. When the alert condition is detected by the system controller, the RESET pin
can be set back to high in order to place the device back in latch mode.
16
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: INA301-Q1
INA301-Q1
www.ti.com
SBOS786A – APRIL 2016 – REVISED JUNE 2016
The latch and transparent modes represented in Figure 38 show that when VIN drops back below the VLIMIT
threshold for the first time, the RESET pin is pulled high. With the RESET pin is pulled high, the device is set to
latch mode, so that the ALERT pin output state does not return high when the input signal drops below the VLIMIT
threshold. Only when the RESET pin is pulled low does the ALERT pin return to the default high level, thus
indicating that the input signal is below the limit threshold. When the input signal drops below the limit threshold
for the second time, the RESET pin is already pulled low. The device is set to transparent mode at this point and
the ALERT pin is pulled back high as soon as the input signal drops below the alert threshold.
VLIMIT
VIN
(VIN+ - VIN-)
0V
Latch Mode
RESET
Transparent Mode
Alert Clears
ALERT
Alert Does Not Clear
Figure 38. Transparent Mode vs Latch Mode
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: INA301-Q1
17
INA301-Q1
SBOS786A – APRIL 2016 – REVISED JUNE 2016
www.ti.com
8 Applications and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The INA301-Q1 enables easy configuration to detect overcurrent conditions in an application. This device is
individually targeted towards unidirectional overcurrent detection of a single threshold. However, this device can
also be paired with additional INA301-Q1 devices and circuitry to create more complex monitoring functional
blocks.
8.1.1 Selecting a Current-Sensing Resistor
The INA301-Q1 measures the differential voltage developed across a resistor when current flows through the
component in order to determine if the current being monitored exceeds a defined limit. This resistor is commonly
referred to as a current-sensing resistor or a current-shunt resistor, with each term commonly used
interchangeably. The flexible design of this device allows for measuring a wide differential input signal range
across the current-sensing resistor.
Selecting the value of this current-sensing resistor is primarily based on two factors: the required accuracy of the
current measurement, and the allowable power dissipation across the current-sensing resistor. Larger voltages
developed across this resistor allow for more accurate measurements to be made. Amplifiers have fixed internal
errors that are largely dominated by the inherent input offset voltage. When the input signal decreases, these
fixed internal amplifier errors become a larger portion of the measurement and increase the uncertainty in the
measurement accuracy. When the input signal increases, the measurement uncertainty is reduced because the
fixed errors are a smaller percentage of the signal being measured. Therefore, the use of larger-value, currentsensing resistors inherently improves measurement accuracy.
However, a system design trade-off must be evaluated through the use of larger input signals that improve
measurement accuracy. Increasing the current sense resistor value results in an increase in power dissipation
across the current-sensing resistor, and also increases the differential voltage developed across the resistor
when current passes through the component. This increase in voltage across the resistor increases the power
that the resistor must be able to dissipate. Decreasing the value of the current-shunt resistor reduces the power
dissipation requirements of the resistor, but increases the measurement errors resulting from the decreased input
signal. Selecting the optimal value for the shunt resistor requires factoring both the accuracy requirement for the
specific application, and the allowable power dissipation of this component.
Low-ohmic-value resistors enable large currents to be accurately monitored with the INA301-Q1. An increasing
number of very low-ohmic-value resistors are becoming more widely available, with values of 200 μΩ and less,
and power dissipations of up to 5 W.
18
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: INA301-Q1
INA301-Q1
www.ti.com
SBOS786A – APRIL 2016 – REVISED JUNE 2016
Application Information (continued)
8.1.1.1 Selecting a Current-Sensing Resistor Example
In this example, the trade-offs involved in selecting a current-sensing resistor are described. This example
requires 2.5% accuracy for detecting a 10-A overcurrent event, with only 250 mW of allowable power dissipation
across the current-sensing resistor at the full-scale current level. Although the maximum power dissipation is
defined as 250 mW, a lower dissipation is preferred in order to improve system efficiency. Some initial
assumptions are made that are used in this example:
• the limit-setting resistor (RLIMIT) is a 1% component
• the maximum tolerance specification for the internal threshold setting current source (0.5%) is used
Given the total error budget of 2.5%, up to 1% of error is available to be attributed to the measurement error of
the device under these conditions.
As shown in Table 5, the maximum value calculated for the current-sensing resistor with these requirements is
2.5 mΩ. Although this value satisfies the maximum power dissipation requirement of 250 mW, headroom is
available from the 2.5% maximum total overcurrent detection error in order to reduce the value of the currentsensing resistor, and reduce the power dissipation further. Selecting a 1.5-mΩ, current-sensing resistor value
offers a good tradeoff for reducing the power dissipation in this scenario by approximately 40% while still
remaining within the accuracy region.
Table 5. Calculating the Current-Sensing Resistor, RSENSE
PARAMETER
EQUATION
IMAX
Maximum current
PD_MAX
Maximum allowable power dissipation
RSENSE_MAX
Maximum allowable RSENSE
VOS
Offset voltage
VOS_ERROR
Initial offset voltage error
EG
Gain error
ERRORTOTAL
Total measurement error
PD_MAX / IMAX2
(VOS / (RSENSE_MAX × IMAX ) × 100
VALUE
UNIT
10
A
250
mW
2.5
mΩ
150
µV
0.6%
0.25%
√(VOS_ERROR2 + EG2)
0.65%
Allowable current threshold accuracy
2.5%
ERRORINITIAL
Initial threshold error
ILIMIT Tolerance + RLIMIT Tolerance
ERRORAVAILABLE
Maximum allowable measurement error
Maximum Error – ERRORINITIAL
1.5%
VOS_ERROR_MAX
Maximum allowable offset error
√(ERRORAVAILABLE2 – EG2)
VDIFF_MIN
Minimum differential voltage
VOS / VOS_ERROR_MAX (1%)
15
mV
RSENSE_MIN
Minimum sense resistor value
VDIFF_MIN / IMAX
1.5
mΩ
PD_MIN
Minimum power dissipation
RSENSE_MIN × IMAX2
150
mW
1%
0.97%
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: INA301-Q1
19
INA301-Q1
SBOS786A – APRIL 2016 – REVISED JUNE 2016
www.ti.com
8.1.2 Input Filtering
External system noise can significantly affect the ability of a comparator to accurately measure and detect
whether input signals exceed the reference threshold levels and reliably indicate overrange conditions. The most
obvious effect that external noise has on the operation of a comparator is to cause a false-alert condition. If a
comparator detects a large noise transient coupled into the signal, the device can easily interpret this transient as
an overrange condition.
External filtering helps reduce the amount of noise that reaches the comparator, and thus reduce the likelihood of
a false alert from occurring. The tradeoff to adding this noise filter is that the alert response time is increased
because of the input signal being filtered along with the noise. Figure 39 shows the implementation of an input
filter for the device.
2.7 V to 5.5 V
CBYPASS
0.1 F
Supply
(0 V to 36 V)
VS
IN+
RFILTER
” 10
CFILTER
INA301-Q1
RPULL-UP
10 k
+
OUT
ALERT
IN±
Load
RESET
LIMIT
GND
RLIMIT
Copyright © 2016, Texas Instruments Incorporated
Figure 39. Input Filter
Limiting the input resistance this filter is important because this resistance can have a significant affect on the
input signal that reaches the device input pins because of the device input bias currents. A typical system
implementation involves placing the current-sensing resistor very near the device so that the traces are very
short and the trace impedance is very small. This layout helps reduce the ability of coupling additional noise into
the measurement. Under these conditions, the characteristics of the input bias currents have minimal affect on
device performance.
As illustrated in Figure 40, the input bias currents increase in opposite directions when the differential input
voltage increases. This increase results from a device design that allows common-mode input voltages to far
exceed the device supply voltage range. With input filter resistors now placed in series with these unequal input
bias currents, there are unequal voltage drops developed across these input resistors. The difference between
these two voltage drops appears as an added signal that, in this case, subtracts from the voltage developed
across the current-sensing resistor, thus reducing the signal that reaches the device input pins. Smaller-value
input resistors reduce this effect of signal attenuation to allow for a more accurate measurement.
20
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: INA301-Q1
INA301-Q1
www.ti.com
SBOS786A – APRIL 2016 – REVISED JUNE 2016
225
Input Bias Current (µA)
200
175
150
125
100
75
50
25
0
0
50
100
150
200
250
Differential Input Voltage (mV)
C002
Figure 40. Input Bias Current vs Differential Input Voltage
For example, with a differential voltage of 10 mV developed across a current-sensing resistor and using 20-Ω
resistors, the differential signal that actually reaches the device is 9.85 mV. A measurement error of 1.5% is
created as a result of these external input filter resistors. Use 10-Ω input filter resistors instead of the 20-Ω
resistors to reduce this added error from 1.5% down to 0.75%.
8.1.3 INA301-Q1 Operation With Common-Mode Voltage Transients Greater Than 36 V
With a small amount of additional circuitry, the INA301-Q1 can be used in circuits subject to transients greater
than 36 V. Use only Zener diodes or Zener-type transient absorbers (sometimes referred to as transzorbs). Any
other type of transient absorber has an unacceptable time delay. Start by adding a pair of resistors as a working
impedance for the zener diode, as shown in Figure 41. Keep these resistors as small as possible; preferably, 10
Ω or less. Larger values can be used, but with an additional induced error resulting from less signal reaching the
device input pins. Because this circuit limits only short-term transients, many applications are satisfied with a 10Ω resistor along with conventional Zener diodes of the lowest power rating available. This combination uses the
least amount of board space. These diodes can be found in packages as small as SOT-523 or SOD-523.
2.7 V to 5.5 V
CBYPASS
0.1 F
Supply
(0 V to 36 V)
VS
IN+
INA301-Q1
RPULL-UP
10k
+
OUT
RPROTECT
” 10
ALERT
IN±
Load
RESET
LIMIT
GND
RLIMIT
Copyright © 2016, Texas Instruments Incorporated
Figure 41. Transient Protection
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: INA301-Q1
21
INA301-Q1
SBOS786A – APRIL 2016 – REVISED JUNE 2016
www.ti.com
8.2 Typical Application
Although this device is only able to measure current through a current-sensing resistor flowing in one direction, a
second INA301-Q1 can be used to create a bidirectional monitor, as shown in Figure 42.
CBYPASS
0.1 F
2.7 V to 5.5 V
RPULL-UP
10 k
VS
IN+
+
OUT
IN±
OCP+
ALERT
Power Supply
(0 V to 36 V)
LIMIT
GND
RLIMIT
Current
CBYPASS
0.1 F
Output
2.7 V to 5.5 V
Load
RPULL-UP
10 k
VS
IN+
+
OUT
IN±
OCP±
ALERT
LIMIT
GND
RLIMIT
Copyright © 2016, Texas Instruments Incorporated
Figure 42. Bidirectional Application
8.2.1 Design Requirements
For this design example, use the parameters listed in Table 6 as the input parameters.
Table 6. Design Parameters
DESIGN PARAMETERS
22
EXAMPLE VALUE
Supply voltage
3.3 V
Common-mode voltage
12 V
Voltage gain
100 V/V
Sense resistance
5 mΩ
Source-current swing
–2 A to +2 A
Voltage trip points
–1 A and +1 A
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: INA301-Q1
INA301-Q1
www.ti.com
SBOS786A – APRIL 2016 – REVISED JUNE 2016
8.2.2 Detailed Design Procedure
First, reverse the input pins of the second INA301-Q1 across the current-sensing resistor. The second device is
now able to detect current flowing in the other direction relative to the first device.
Then, select limit resistors to set the voltage trip points by using the equations in Table 1. For this application
example, these equations give a value of 6.25 kΩ for both limit resistors.
Connect the outputs of each device to an AND gate in order to detect if either of the limit threshold levels are
exceeded. As shown in Table 7, the output of the AND gate is high if neither overcurrent limit thresholds are
exceeded. A low output state of the AND gate indicates that either the positive overcurrent limit or the negative
overcurrent limit are surpassed.
Table 7. Bidirectional Overcurrent Output Status
OCP STATUS
OUTPUT
OCP+
0
OCP–
0
No OCP
1
8.2.3 Application Curve
Input
(5 mV/div)
Alert Output
(1 V/div)
Figure 43 shows two INA301-Q1 devices being used in a bidirectional configuration and an output control circuit
to detect if one of the two alerts is exceeded.
Positive Limit
0V
Negtive Limit
Time (5 ms/div)
Figure 43. Bidirectional Application Curve
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: INA301-Q1
23
INA301-Q1
SBOS786A – APRIL 2016 – REVISED JUNE 2016
www.ti.com
9 Power Supply Recommendations
The device input circuitry accurately measures signals on common-mode voltages beyond the power-supply
voltage, VS. For example, the voltage applied to the VS power-supply pin can be 5 V, whereas the load powersupply voltage being monitored (VCM) can be as high as 36 V. Also, the device withstands the full –0.3-V to 36-V
range at the input pins, regardless of whether the device has power applied or not.
Power-supply bypass capacitors are required for stability and must be placed as close as possible to the supply
and ground pins of the device. A typical value for this supply bypass capacitor is 0.1 µF. Applications with noisy
or high-impedance power supplies may require additional decoupling capacitors to reject power-supply noise.
10 Layout
10.1 Layout Guidelines
•
•
•
Place the power-supply bypass capacitor as close as possible to the supply and ground pins. The
recommended value of this bypass capacitor is 0.1 µF. Add more decoupling capacitance to compensate for
noisy or high-impedance power supplies.
Connect RLIMIT to the ground pin as directly as possible in order to limit additional capacitance on this node. If
possible, route this connection to the same plane in order to avoid vias to internal planes. If the connection
cannot be routed on the same plane and must pass through vias, make sure that a path is routed from RLIMIT
back to the ground pin, and that RLIMIT is not simply connected directly to a ground plane.
Pull up the open-drain output pin to the supply voltage rail through a 10-kΩ pullup resistor.
10.2 Layout Example
RSHUNT
Power
Supply
Load
Alert Output
5
ALERT RESET
6
IN±
7
8
IN+
RPULL-UP
VIA to
Ground
Plane
CBYPASS
1
2
3
4
INA301-Q1
VS
OUT
LIMIT
GND
Supply
Voltage
VIA to
Ground
Plane
RLIMIT
Output Voltage
Copyright © 2016, Texas Instruments Incorporated
NOTE: Connect the limit resistor directly to the GND pin.
Figure 44. Recommended Layout
24
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: INA301-Q1
INA301-Q1
www.ti.com
SBOS786A – APRIL 2016 – REVISED JUNE 2016
11 Device and Documentation Support
11.1 Documentation Support
11.1.1 Related Documentation
INA301EVM User Guide (SBOU154)
11.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
11.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.5 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
11.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: INA301-Q1
25
PACKAGE OPTION ADDENDUM
www.ti.com
24-Jun-2016
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
INA301A1QDGKRQ1
ACTIVE
VSSOP
DGK
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-2-260C-1 YEAR
-40 to 125
ZGG6
INA301A1QDGKTQ1
ACTIVE
VSSOP
DGK
8
250
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-2-260C-1 YEAR
-40 to 125
ZGG6
INA301A2QDGKRQ1
ACTIVE
VSSOP
DGK
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-2-260C-1 YEAR
-40 to 125
ZGK6
INA301A2QDGKTQ1
ACTIVE
VSSOP
DGK
8
250
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-2-260C-1 YEAR
-40 to 125
ZGK6
INA301A3QDGKRQ1
ACTIVE
VSSOP
DGK
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-2-260C-1 YEAR
-40 to 125
ZGJ6
INA301A3QDGKTQ1
ACTIVE
VSSOP
DGK
8
250
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-2-260C-1 YEAR
-40 to 125
ZGJ6
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
24-Jun-2016
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF INA301-Q1 :
• Catalog: INA301
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Jun-2016
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
INA301A1QDGKRQ1
VSSOP
DGK
8
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
2500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
INA301A1QDGKTQ1
VSSOP
DGK
8
250
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
INA301A2QDGKRQ1
VSSOP
DGK
8
2500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
INA301A2QDGKTQ1
VSSOP
DGK
8
250
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
INA301A3QDGKRQ1
VSSOP
DGK
8
2500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
INA301A3QDGKTQ1
VSSOP
DGK
8
250
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Jun-2016
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
INA301A1QDGKRQ1
VSSOP
DGK
8
2500
366.0
364.0
50.0
INA301A1QDGKTQ1
VSSOP
DGK
8
250
366.0
364.0
50.0
INA301A2QDGKRQ1
VSSOP
DGK
8
2500
366.0
364.0
50.0
INA301A2QDGKTQ1
VSSOP
DGK
8
250
366.0
364.0
50.0
INA301A3QDGKRQ1
VSSOP
DGK
8
2500
366.0
364.0
50.0
INA301A3QDGKTQ1
VSSOP
DGK
8
250
366.0
364.0
50.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated