SOLID TANTALUM ELECTROLYTIC CAPACITORS F98 Resin-molded Chip, High Capacitance Series Specifications Compliant to the RoHS directive (2002/95/EC). Item Applications Smartphone Mobile phone Wireless module Hearing aid Performance Characteristics Category Temperature Range --55 to +125°C (Rated temperature : +85°C) Capacitance Tolerance ±20% (at 120Hz) Dissipation Factor Refer to the table below ESR Refer to the table below Leakage Current Refer to the table below Provided that After 5 minute's application of rated voltage, leakage current at 85°C, 10 times or less than 20°C specified value. After 5 minute's application of rated voltage, leakage current at 125°C, 12.5 times or less than 20°C specified value. Damp Heat (Steady State) At 40°C, 90 to 95% R.H., For 500hours (No voltage applied) Capacitance Change Refer to the table below (* 1) Dissipation Factor 150% or less of initial specified value Leakage Current 200% or less of initial specified value Temperature Cycles At --55°C / +125°C, For 30 minutes each, 5 cycles Capacitance Change Refer to the table below (* 1) 150% or less than the initial specified value Dissipation Factor Leakage Current Initial specified value or less Resistance to Soldering Heat 10 seconds reflow at 260°C, 5 seconds immersion at 260°C Capacitance Change Refer to the table below (* 1) Leakage Current Initial specified value or less Leakage Current Initial specified value or less Surge∗ After application of surge in series with a 1kΩ resistor at the rate of 30 seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85°C, capacitors shall meet the characteristic requirements listed below. Refer to the table below (* 1) Capacitance Change Dissipation Factor 150% or less than the initial specified value Leakage Current 200% or less than the initial specified value Endurance∗ After 1000 hours' application of rated voltage in series with a 3Ω resistor at 85°C, capacitors shall meet the characteristic requirements table below Capacitance Change Refer to the table below (* 1) Dissipation Factor 150% or less than the initial specified value Leakage Current 200% or less than the initial specified value Shear Test After applying the pressure load of 5N for 10±1 seconds horizontally to the center of capacitor side body which has no electrode and has been soldered beforehand on a substrate, there shall be found neither exfoliation nor its sign at the terminal electrode. Terminal Strength Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of capacitor, the pressure strength is applied with 20 a specified jig at the center of the R230 substrate so that substrate may bend by 1mm as illustrated. Then, there shall be found no remarkable abnormality on the 45 45 capacitor terminals. Type numbering system (Example : 6.3V 10µF) 1 2 3 4 5 6 7 8 9 10 F 9 8 0 J 1 0 6 M M 11 Taping code (Refer to page 333 for details) Case code Capacitance tolerance Rated capacitance Rated voltage Series Drawing L W1 H W2 S1 S2 S1 (mm) W2 W1 L H 1.10 ± 0.05 0.60 ± 0.05 0.35 ± 0.05 U + 0.55 ± 0.05 0.3 ± 0.05 0.5 ± 0.05 +0.2 M 0.2 1.6 -0.1 0.85 - 0.1 0.65 ± 0.1 0.8 ± 0.1 0.5 ± 0.1 S + 0.2 2.0 -0.1 1.25 - 0.1 +0.2 S2 S1 0.9 ± 0.1 0.8 ± 0.1 0.5 ± 0.1 0.6 ± 0.1 1.0 ± 0.1 1mm Case Code Marking U Case M Case Capacitance code S Case J ∗ As for the surge voltage, refer to page 332 for details. Js Rated voltage (Voltage code) Cap.(µF) Code 1 105 2.2 225 4.7 475 10 22 4 0G 6.3 0J 10 1A 16 1C 20 1D 25 1E Capacitance code M M M --- U•M M --- (U) • M M --- S a U U•M 106 U (U) • M M 226 M M (M) • S J 33 336 M M (M) • S n 47 476 M M S S 68 686 M • S 100 107 M • S 220 227 • S ( ) The series in parentheses are being developed. Please contact to your local Nichicon sales office when these series are being designed in your application. We can consider the type of compliance to AEC-Q200. Please contact to your local Nichicon sales office when these series are being designed in your application. (Ω@100kHz) ESR *1 ∆C/C (%) F980G475MUA F980G106MUA F980G226MMA F980G336MMA F980G476MMA F980G686MMA F980G686MSA F980G107MMA F980G107MSA F980G227MSA 0.5 0.8 0.9 1.3 1.9 27.2 2.7 80.0 4.0 132 20 25 15 30 40 50 30 60 35 80 20 20 7.5 4 8 10 4 10 4 5 ±30 ±30 ±30 ±30 ±30 ±30 ±30 ±30 ±30 ±30 F980J475MUA F980J475MMA F980J106MMA F980J226MMA F980J336MMA F980J476MMA F980J476MSA F980J107MSA F981A225MUA F981A225MMA F981A475MMA F981A106MMA F981A226MSA F981A336MSA F981A476MSA F981C105MMA F981C225MMA F981C475MMA F981C106MSA F981D105MMA F981E105MMA 0.6 0.5 0.6 1.4 4.2 29.6 3.0 63.0 0.5 0.5 0.5 1.0 2.2 3.3 9.4 0.5 0.5 0.8 1.6 0.5 0.5 20 20 8 20 35 45 25 50 15 6 6 20 20 30 35 6 6 12 18 6 8 20 7.5 6 6 8 10 6 8 15 7.5 6 7.5 4 6 5 10 10 12 4 10 10 ±30 ±30 ±30 ±30 ±30 ±30 ±30 ±30 ±30 ±30 ±30 ±30 ±20 ±30 ±30 ±30 ±30 ±30 ±20 ±30 ±30 Case code Part Number 4V 4.7 10 22 33 47 68 68 100 100 220 U U M M M M S M S S 4.7 4.7 10 22 33 47 47 100 2.2 2.2 4.7 10 22 33 47 1 2.2 4.7 10 1 1 U M M M M M S S U M M M S S S M M M S M M 6.3V s A Disspation Factor (% @120Hz) Rated Capacitance (µF) w S Current (µA) Rated Volt Rated voltage (Voltage code) Standard Ratings V 5N (0.51kg • f) For 10 ± 1 seconds 10V J 16V 20V 25V *2 Leakage *2 : Leakage Current After 5 minute's application of rated voltage, leakage current at 20˚C. CAT.8100B