Fairchild FDG1024NZ Dual n-channel powertrenchâ® mosfet 20 v, 1.2 a, 175 mî© Datasheet

FDG1024NZ
Dual N-Channel PowerTrench® MOSFET
20 V, 1.2 A, 175 mΩ
Features
General Description
„ Max rDS(on) = 175 mΩ at VGS = 4.5 V, ID = 1.2 A
This dual N-Channel logic level enhancement mode field effect
transistors are produced using Fairchild’s proprietary, high cell
density, DMOS technology. This very high density process is
especially tailored to minimize on-state resistance. This device
has been designed especially for low voltage applications as a
replacement for bipolar digital transistors and small signal
MOSFETs. Since bias resistors are not required, this dual digital
FET can replace several different digital transistors, with
different bias resistor values.
„ Max rDS(on) = 215 mΩ at VGS = 2.5 V, ID = 1.0 A
„ Max rDS(on) = 270 mΩ at VGS = 1.8 V, ID = 0.9 A
„ Max rDS(on) = 389 mΩ at VGS = 1.5 V, ID = 0.8 A
„ HBM ESD protection level >2 kV (Note 3)
„ Very low level gate drive requirements allowing operation in
3 V circuits (VGS(th) < 1.5 V)
„ Very small package outline SC70-6
„ RoHS Compliant
S2
G2
D1
S1 1
6 D1
G1 2
5 G2
D2 3
4 S2
D2
S1
G1
SC70-6
MOSFET Maximum Ratings TA = 25 °C unless otherwise noted
Symbol
VDS
Drain to Source Voltage
Parameter
VGS
Gate to Source Voltage
-Continuous
ID
TA = 25°C
(Note 1a)
-Pulsed
PD
TJ, TSTG
Ratings
20
Units
V
±8
V
1.2
6
Power Dissipation
TA = 25°C
(Note 1a)
0.36
Power Dissipation
TA = 25°C
(Note 1b)
0.30
Operating and Storage Junction Temperature Range
-55 to +150
A
W
°C
Thermal Characteristics
RθJA
Thermal Resistance, Junction to Ambient
(Note 1a)
350
RθJA
Thermal Resistance, Junction to Ambient
(Note 1b)
415
°C/W
Package Marking and Ordering Information
Device Marking
.24
Device
FDG1024NZ
©2009 Fairchild Semiconductor Corporation
FDG1024NZ Rev.B
Package
SC70-6
1
Reel Size
7”
Tape Width
8 mm
Quantity
3000 units
www.fairchildsemi.com
FDG1024NZ Dual N-Channel Power Trench® MOSFET
August 2009
Symbol
Parameter
Test Conditions
Min
Typ
Max
Units
Off Characteristics
BVDSS
Drain to Source Breakdown Voltage
ID = 250 µA, VGS = 0 V
∆BVDSS
∆TJ
Breakdown Voltage Temperature
Coefficient
ID = 250 µA, referenced to 25 °C
IDSS
Zero Gate Voltage Drain Current
VDS = 16 V, VGS = 0 V
1
µA
IGSS
Gate to Source Leakage Current
VGS = ±8 V, VDS = 0 V
±10
µA
1.0
V
20
V
14
mV/°C
On Characteristics
VGS(th)
Gate to Source Threshold Voltage
VGS = VDS, ID = 250 µA
∆VGS(th)
∆TJ
Gate to Source Threshold Voltage
Temperature Coefficient
ID = 250 µA, referenced to 25 °C
rDS(on)
gFS
Static Drain to Source On Resistance
Forward Transconductance
0.4
0.8
-3
mV/°C
VGS = 4.5 V, ID = 1.2 A
160
175
VGS = 2.5 V, ID = 1.0 A
185
215
VGS = 1.8 V, ID = 0.9 A
232
270
VGS = 1.5 V, ID = 0.8 A
321
389
VGS = 4.5 V, ID = 1.2 A,
TJ =125 °C
220
259
VDD = 5 V, ID = 1.2 A
4
mΩ
S
Dynamic Characteristics
Ciss
Input Capacitance
Coss
Output Capacitance
Crss
Reverse Transfer Capacitance
Rg
Gate Resistance
VDS = 10 V, VGS = 0 V,
f = 1 MHz
115
150
pF
25
35
pF
20
25
pF
Ω
4.6
Switching Characteristics
td(on)
Turn-On Delay Time
3.7
10
ns
tr
Rise Time
1.7
10
ns
td(off)
Turn-Off Delay Time
11
19
ns
tf
Fall Time
1.5
10
ns
Qg
Total Gate Charge
1.8
2.6
nC
Qgs
Gate to Source Charge
Qgd
Gate to Drain “Miller” Charge
VDD = 10 V, ID = 1.2 A,
VGS = 4.5 V, RGEN = 6 Ω
VGS = 4.5 V, VDD = 10 V,
ID = 1.2 A
0.3
nC
0.4
nC
Drain-Source Diode Characteristics
IS
Maximum Continuous Drain-Source Diode Forward Current
VSD
Source to Drain Diode Forward Voltage
trr
Reverse Recovery Time
Qrr
Reverse Recovery Charge
VGS = 0 V, IS = 0.3 A
0.3
(Note 2)
IF = 1.2 A, di/dt = 100 A/µs
A
0.7
1.2
V
10
20
ns
1.9
10
nC
NOTES:
1. RθJA is determined with the device mounted on a 1 in2 pad 2 oz copper pad on a 1.5 x 1.5 in. board of FR-4 material. RθJC is guaranteed by design while RθJA is determined by
the user's board design.
a. 350 °C/W when mounted
on a 1 in2 pad of 2 oz copper.
b. 415 °C/W when mounted on a
minimum pad of 2 oz copper.
2. Pulse Test: Pulse Width < 300 µs, Duty cycle < 2.0%.
3: The diode connected between the gate and source serves only as protection against ESD. No gate overvoltage rating is implied.
©2009 Fairchild Semiconductor Corporation
FDG1024NZ Rev.B
2
www.fairchildsemi.com
FDG1024NZ Dual N-Channel Power Trench® MOSFET
Electrical Characteristics TJ = 25 °C unless otherwise noted
2.5
6
VGS = 3.5 V
ID, DRAIN CURRENT (A)
5
NORMALIZED
DRAIN TO SOURCE ON-RESISTANCE
VGS = 4.5 V
VGS = 2.5 V
4
PULSE DURATION = 80 µs
DUTY CYCLE = 0.5% MAX
3
VGS = 1.8 V
2
1
VGS = 1.5 V
0
0
0.4
0.8
1.2
1.6
VGS = 1.5 V
VGS = 3.5 V
1.5
1.0
VGS = 4.5 V
PULSE DURATION = 80 µs
DUTY CYCLE = 0.5% MAX
0.5
2.0
0
1
2
3
4
5
6
ID, DRAIN CURRENT (A)
Figure 1. On-Region Characteristics
Figure 2. Normalized On-Resistance
vs Drain Current and Gate Voltage
1.6
600
ID = 1.2 A
VGS = 4.5 V
rDS(on), DRAIN TO
1.4
1.2
1.0
0.8
0.6
-75
-50
SOURCE ON-RESISTANCE (mΩ)
NORMALIZED
DRAIN TO SOURCE ON-RESISTANCE
VGS = 2.5 V
2.0
VDS, DRAIN TO SOURCE VOLTAGE (V)
PULSE DURATION = 80 µs
DUTY CYCLE = 0.5% MAX
500
ID = 1.2 A
400
300
TJ = 125 oC
200
100
0
1.0
-25
0
25 50 75 100 125 150
TJ, JUNCTION TEMPERATURE (oC)
TJ = 25 oC
1.5
2.0
2.5
3.0
3.5
4.0
4.5
VGS, GATE TO SOURCE VOLTAGE (V)
Figure 3. Normalized On- Resistance
vs Junction Temperature
Figure 4. On-Resistance vs Gate to
Source Voltage
10
6
IS, REVERSE DRAIN CURRENT (A)
PULSE DURATION = 80 µs
DUTY CYCLE = 0.5% MAX
5
ID, DRAIN CURRENT (A)
VGS = 1.8 V
VDS = 5 V
4
3
TJ = 25 oC
2
TJ = 125 oC
1
VGS = 0 V
1
TJ = 125 oC
TJ = 25 oC
0.1
TJ = -55 oC
TJ = -55 oC
0.01
0.2
0
0
1
2
3
4
0.4
0.6
0.8
1.0
1.2
VGS, GATE TO SOURCE VOLTAGE (V)
VSD, BODY DIODE FORWARD VOLTAGE (V)
Figure 5. Transfer Characteristics
Figure 6. Source to Drain Diode
Forward Voltage vs Source Current
©2009 Fairchild Semiconductor Corporation
FDG1024NZ Rev.B
3
1.4
www.fairchildsemi.com
FDG1024NZ Dual N-Channel Power Trench® MOSFET
Typical Characteristics TJ = 25 °C unless otherwise noted
300
VGS, GATE TO SOURCE VOLTAGE (V)
5
ID = 1.2 A
Ciss
CAPACITANCE (pF)
4
VDD = 5 V
3
VDD = 10 V
2
VDD = 15 V
1
100
Coss
10
5
0.1
0
0
0.5
1.0
1.5
2.0
2.5
1
10
20
VDS, DRAIN TO SOURCE VOLTAGE (V)
Qg, GATE CHARGE (nC)
Figure 7. Gate Charge Characteristics
Figure 8. Capacitance vs Drain
to Source Voltage
10
5
10
Ig, GATE LEAKAGE CURRENT (µA)
THIS AREA IS
LIMITED BY rDS(on)
ID, DRAIN CURRENT (A)
Crss
f = 1 MHz
VGS = 0 V
0.1 ms
1
1 ms
10 ms
0.1
SINGLE PULSE
TJ = MAX RATED
100 ms
RθJA = 415 oC/W
1s
DC
o
TA = 25 C
0.01
0.01
0.1
1
10
VGS = 0 V
3
10
TJ = 125 oC
10
-1
10
TJ = 25 oC
-3
10
100
0
VDS, DRAIN to SOURCE VOLTAGE (V)
2
4
6
8
10
12
14
VGS, GATE TO SOURCE VOLTAGE (V)
Figure 9. Forward Bias Safe
Operating Area
Figure 10. Gate Leakage Current vs Gate to Source
Voltage
P(PK), PEAK TRANSIENT POWER (W)
100
VGS = 4.5 V
SINGLE PULSE
RθJA = 415 oC/W
10
TA = 25 oC
1
0.1
-4
10
-3
10
-2
10
-1
10
1
10
100
1000
t, PULSE WIDTH (sec)
Figure 11. Single Pulse Maximum Power Dissipation
©2009 Fairchild Semiconductor Corporation
FDG1024NZ Rev.B
4
www.fairchildsemi.com
FDG1024NZ Dual N-Channel Power Trench® MOSFET
Typical Characteristics TJ = 25 °C unless otherwise noted
2
NORMALIZED THERMAL
IMPEDANCE, ZθJA
1
0.1
DUTY CYCLE-DESCENDING ORDER
D = 0.5
0.2
0.1
0.05
0.02
0.01
PDM
t1
t2
0.01
NOTES:
DUTY FACTOR: D = t1/t2
PEAK TJ = PDM x ZθJA x RθJA + TA
SINGLE PULSE
o
RθJA = 415 C/W
0.001
-4
10
-3
10
-2
10
-1
10
1
10
100
1000
t, RECTANGULAR PULSE DURATION (sec)
Figure 12. Transient Thermal Response Curve
©2009 Fairchild Semiconductor Corporation
FDG1024NZ Rev.B
5
www.fairchildsemi.com
FDG1024NZ Dual N-Channel Power Trench® MOSFET
Typical Characteristics TJ = 25 °C unless otherwise noted
FDG1024NZ Dual N-Channel Power Trench® MOSFET
Dimensional Outline and Pad Layout
©2009 Fairchild Semiconductor Corporation
FDG1024NZ Rev.B
6
www.fairchildsemi.com
tm
tm
*Trademarks of System General Corporation, used under license by Fairchild Semiconductor.
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE
RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY
PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY
THEREIN, WHICH COVERS THESE PRODUCTS.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE
EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION.
As used herein:
1. Life support devices or systems are devices or systems which, (a) are
intended for surgical implant into the body or (b) support or sustain life,
and (c) whose failure to perform when properly used in accordance with
instructions for use provided in the labeling, can be reasonably
expected to result in a significant injury of the user.
2.
A critical component in any component of a life support, device, or
system whose failure to perform can be reasonably expected to cause
the failure of the life support device or system, or to affect its safety or
effectiveness.
ANTI-COUNTERFEITING POLICY
Fairchild Semiconductor Corporation’s Anti-Counterfeiting Policy. Fairchild’s Anti-Counterfeiting Policy is also stated on our external website,
www.Fairchildsemi.com, under Sales Support.
Counterfeiting of semiconductor parts is a growing problem in the industry. All manufactures of semiconductor products are experiencing counterfeiting of their
parts. Customers who inadvertently purchase counterfeit parts experience many problems such as loss of brand reputation, substandard performance, failed
application, and increased cost of production and manufacturing delays. Fairchild is taking strong measures to protect ourselves and our customers from the
proliferation of counterfeit parts. Fairchild strongly encourages customers to purchase Fairchild parts either directly from Fairchild or from Authorized Fairchild
Distributors who are listed by country on our web page cited above. Products customers buy either from Fairchild directly or from Authorized Fairchild
Distributors are genuine parts, have full traceability, meet Fairchild’s quality standards for handing and storage and provide access to Fairchild’s full range of
up-to-date technical and product information. Fairchild and our Authorized Distributors will stand behind all warranties and will appropriately address and
warranty issues that may arise. Fairchild will not provide any warranty coverage or other assistance for parts bought from Unauthorized Sources. Fairchild is
committed to combat this global problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized distributors.
PRODUCT STATUS DEFINITIONS
Definition of Terms
Datasheet Identification
Product Status
Definition
Advance Information
Formative / In Design
Datasheet contains the design specifications for product development. Specifications
may change in any manner without notice.
Preliminary
First Production
Datasheet contains preliminary data; supplementary data will be published at a later
date. Fairchild Semiconductor reserves the right to make changes at any time without
notice to improve design.
No Identification Needed
Full Production
Datasheet contains final specifications. Fairchild Semiconductor reserves the right to
make changes at any time without notice to improve the design.
Obsolete
Not In Production
Datasheet contains specifications on a product that is discontinued by Fairchild
Semiconductor. The datasheet is for reference information only.
Rev. I41
©2009 Fairchild Semiconductor Corporation
FDG1024NZ Rev.B
7
www.fairchildsemi.com
FDG1024NZ Dual N-Channel Power Trench® MOSFET
TRADEMARKS
The following includes registered and unregistered trademarks and service marks, owned by Fairchild Semiconductor and/or its global subsidiaries, and is not
intended to be an exhaustive list of all such trademarks.
AccuPower™
PowerTrench®
FPS™
The Power Franchise®
Auto-SPM™
F-PFS™
PowerXS™
®
®
Build it Now™
FRFET
Programmable Active Droop™
SM
®
CorePLUS™
Global Power Resource
QFET
TinyBoost™
CorePOWER™
Green FPS™
QS™
TinyBuck™
CROSSVOLT™
Green FPS™ e-Series™
Quiet Series™
TinyCalc™
CTL™
Gmax™
RapidConfigure™
TinyLogic®
Current Transfer Logic™
GTO™
®
TINYOPTO™
EcoSPARK
IntelliMAX™
™
TinyPower™
EfficentMax™
Saving our world, 1mW /W /kW at a time™
ISOPLANAR™
TinyPWM™
SmartMax™
EZSWITCH™*
MegaBuck™
TinyWire™
™*
SMART START™
MICROCOUPLER™
®
TriFault Detect™
SPM
MicroFET™
TRUECURRENT™*
STEALTH™
MicroPak™
®
SuperFET™
MillerDrive™
®
Fairchild
SuperSOT™-3
MotionMax™
Fairchild Semiconductor®
SuperSOT™-6
UHC®
Motion-SPM™
®
FACT Quiet Series™
Ultra FRFET™
SuperSOT™-8
OPTOLOGIC
FACT®
OPTOPLANAR®
UniFET™
SupreMOS™
®
®
FAST
VCX™
SyncFET™
FastvCore™
VisualMax™
Sync-Lock™
FETBench™
XS™
®*
PDP
SPM™
®
FlashWriter *
Power-SPM™
Similar pages