TI1 CD74ACT297 Digital phase-locked loop Datasheet

CD74ACT297
DIGITAL PHASE-LOCKED LOOP
SCHS297D – AUGUST 1998 – REVISED JUNE 2002
D
D
D
D
D
D
D
D
D
D
D
M PACKAGE
(TOP VIEW)
Speed of Bipolar FCT, AS, and S, With
Significantly Reduced Power Consumption
Digital Design Avoids Analog
Compensation Errors
Easily Cascadable for Higher-Order Loops
Useful Frequency Range
– DC to 110 MHz Typical (K CLK)
– DC to 70 MHz Typical (I/D CLK)
Dynamically Variable Bandwidth
Very Narrow Bandwidth Attainable
Power-On Reset
Output Capability
– Standard: XORPD OUT, ECPD OUT
– Bus Driver: I/D OUT
SCR Latch-Up-Resistant CMOS Process
and Circuit Design
Balanced Propagation Delays
ESD Protection Exceeds 2000 V Per
MIL-STD-883, Method 3015
B
A
ENCTR
K CLK
I/D CLK
D/U
I/D OUT
GND
1
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
VCC
C
D
φA2
ECPD OUT
XORPD OUT
φB
φA1
description/ordering information
The CD74ACT297 provides a simple, cost-effective solution to high-accuracy, digital, phase-locked-loop
applications. This device contains all the necessary circuits, with the exception of the divide-by-N counter, to
build first-order phase-locked loops as shown in Figure 1.
Both exclusive-OR phase detectors (XORPDs) and edge-controlled (ECPD) phase detectors are provided for
maximum flexibility.
Proper partitioning of the loop function, with many of the building blocks external to the package, makes it easy
for the designer to incorporate ripple cancellation or to cascade to higher-order phase-locked loops.
The length of the up/down K counter is digitally programmable according to the K-counter function table. With
A, B, C, and D all low, the K counter is disabled. With A high and B, C, and D low, the K counter is only three
stages long, which widens the bandwidth, or capture range, and shortens the lock time of the loop. When A,
B, C, and D are programmed high, the K counter becomes 17 stages long, which narrows the bandwidth, or
capture range, and lengthens the lock time. Real-time control of loop bandwidth by manipulating the
A-through-D inputs can maximize the overall performance of the digital phase-locked loop.
ORDERING INFORMATION
–55°C
55°C to 125°C
ORDERABLE
PART NUMBER
PACKAGE†
TA
SOIC – M
Tube
CD74ACT297M
Tape and reel
CD74ACT297M96
TOP-SIDE
MARKING
ACT297M
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design
guidelines are available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2002, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
CD74ACT297
DIGITAL PHASE-LOCKED LOOP
SCHS297D – AUGUST 1998 – REVISED JUNE 2002
description/ordering information (continued)
This device performs the classic first-order phase-locked-loop function without using analog components. The
accuracy of the digital phase-locked loop (DPLL) is not affected by VCC and temperature variations, but depends
solely on accuracies of the K clock (K CLK), increment/decrement clock (I/D CLK), and loop propagation delays.
The I/D clock frequency and the divide-by-N modulos determine the center frequency of the DPLL. The center
frequency is defined by the relationship fc = I/D clock/2N (Hz).
Modulo Controls
D C
B
A
14 15 1
K CLK
D/U
ENCTR
I/D CLK
2
4
6
3
Modulo K
Counter
5
φA1
9
φB
10
φA2
13
Increment/Decrement
Circuit
11
J
12
K
Figure 1. Simplified Block Diagram
2
7
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
I/D OUT
XORPD OUT
ECPD OUT
CD74ACT297
DIGITAL PHASE-LOCKED LOOP
SCHS297D – AUGUST 1998 – REVISED JUNE 2002
Function Tables
K COUNTER
(digital control)
D
C
B
L
L
L
L
L
A
MODULO (K)
L
L
L
H
Inhibited
23
L
H
L
L
L
H
H
L
H
L
L
L
H
L
H
L
H
H
L
L
H
H
H
H
L
L
L
H
L
L
H
H
L
H
L
H
L
H
H
H
H
L
L
H
H
L
H
H
H
H
L
H
H
H
H
24
25
26
27
28
29
210
211
212
213
214
215
216
217
EXCLUSIVE-OR PHASE DETECTOR
φA1
φB
XORPD OUT
L
L
L
L
H
H
H
L
H
H
H
L
EDGE-CONTROLLED PHASE DETECTOR
φA2
φB
ECPD OUT
H or L
↓
H
↓
H or L
L
H or L
↑
No change
↑
H or L
No change
H = steady-state high level
L = steady-state low level
↓ = transition from high to low
↑ = transition from low to high
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
CD74ACT297
DIGITAL PHASE-LOCKED LOOP
SCHS297D – AUGUST 1998 – REVISED JUNE 2002
functional block diagram
K Counter
A
B
C
D
2
1
2
4
8
1
15
14
X/Y
0
14
13
12
11
10
9
8
7
6
5
4
3
2
1
To Mode Controls 12–2 (11 stages not shown)
K CLK
D/U
ENCTR
4
R
C20
6
20D
R
C20
3
T
20D
M13
M14
M13
14T
R
13T
R
1T
T
1T
T
13D
14D
R
R
13T
M14
T
R
13D
14T
T
T
R
14D
R
R
R
R
Power-Up Reset
l=1
Decrement
1
Increment
I/D CLK
I/D Circuit
5
7
I/D OUT
21D
21D
21D
C21
21D
C21
C21
21J
C21
C21
C21
C21
C21
21D
C21
21D
21K
21D
21D
Exclusive-OR Phase Detector
φA1
9
11
φB
XORPD OUT
10
Edge-Controlled Phase Detector
S
R
φA2
4
12
S
R
13
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
ECPD OUT
CD74ACT297
DIGITAL PHASE-LOCKED LOOP
SCHS297D – AUGUST 1998 – REVISED JUNE 2002
detailed description
The phase detector generates an error-signal waveform that, at zero phase error, is a 50% duty-cycle square wave.
At the limits of linear operation, the phase-detector output is either high or low all of the time, depending on the
direction of the phase error (φin – φout). Within these limits, the phase-detector output varies linearly with the input
phase error according to the gain kd, which is expressed in terms of phase-detector output per cycle of phase error.
The phase-detector output can be varied between ±1 according to the relation:
Phase-detector output
+ % high100– % low
(1)
The output of the phase detector is kd φe, where the phase error φe = φin – φout.
XORPD and ECPD are commonly used digital types. The ECPD is more complex than the XORPD, but can be
described generally as a circuit that changes states on one of the transitions of its inputs. For an XORPD, kd = 4,
because its output remains high (PD output = 1) for a phase error of one-fourth cycle. Similarly, for the ECPD,
kd = 2, because its output remains high for a phase error of one-half cycle. The type of phase detector determines
the zero-phase-error point, i.e., the phase separation of the phase-detector inputs for φe is defined to be zero. For
the basic DPLL system of Figure 2, φe = 0 when the phase-detector output is a square wave. The XORPD inputs are
one-fourth cycle out of phase for zero phase error. For the ECPD, φe = 0 when the inputs are one-half cycle out of
phase.
K CLK
Mfc
Carry
Divide-by-K
Counter
D/U
Borrow
XORPD OUT
fin,
φin
φA1
φB
I/D CLK
I/D Circuit
I/D OUT
fout,
φout
2Nfc
Divide-by-N
Counter
Figure 2. DPLL Using Exclusive-OR Phase Detection
The phase-detector output controls the up/down input to the K counter. The counter is clocked by input frequency
Mfc, which is a multiple M of the loop center frequency fc. When the K counter recycles up, it generates a carry pulse.
Recycling while counting down generates a borrow pulse. If the carry and borrow outputs are conceptually combined
into one output that is positive for a carry and negative for a borrow, and if the K counter is considered as a frequency
divider with the ratio Mfc/K, the output of the K counter equals the input frequency multiplied by the division ratio. Thus,
the output from the K counter is kdφeMfc/K.
The carry and borrow pulses go to the increment/decrement (I/D) circuit, which, in the absence of any carry or borrow
pulse, has an output that is one-half of the input clock (I/D CLK). The input clock is just a multiple (2N) of the loop
center frequency. In response to a carry or borrow pulse, the I/D circuit either adds or deletes a pulse at I/D OUT. Thus,
the output of the I/D circuit is Nfc + (kdφeMfc)/2K.
The output of the N counter (or the output of the phase-locked loop) is:
fo
+ fc ) (kdfeMfc)ń2KN
(2)
When this result is compared to the equation for a first-order analog phase-locked loop, the digital equivalent of the
gain of the VCO is Mfc/2KN, or fc/K for M = 2N.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
CD74ACT297
DIGITAL PHASE-LOCKED LOOP
SCHS297D – AUGUST 1998 – REVISED JUNE 2002
detailed description (continued)
Thus, the simple first-order phase-locked loop with an adjustable K counter is the equivalent of an analog
phase-locked loop with a programmable VCO gain.
Mfc
K CLK
Carry
Divide-by-K
Counter
D/U
ENCTR
Borrow
XORPD OUT
φA1
fout,
φout
φB
I/D CLK
J
fin,
φin
φA2
I/D Circuit
ECPD
2 Nfc
K
I/D OUT
Divide-by-N
Counter
Figure 3. DPLL Using Both Phase Detectors in a Ripple-Cancellation Scheme
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 6 V
DC input diode current, IIK (VI < –0.5 V or VI > VCC + 0.5 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA
DC input diode current, IOK (VO < –0.5 V or VO > VCC + 0.5 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA
DC output source or sink current per output pin, IO (VO > –0.5 V or VO < VCC + 0.5 V) . . . . . . . . . . ±50 mA
Continuous current through VCC or GND (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±100 mA
Package thermal impedance, θJA (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73°C/W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. For up to four outputs per device, add ±25 mA for each additional output.
2. The package thermal impedance is calculated in accordance with JESD 51-7.
recommended operating conditions
6
MIN
MAX
4.5
5.5
VCC
VIH
Supply voltage
VIL
VI
Low-level input voltage
Input voltage
0
VO
∆t/∆v
Output voltage
TA
Operating free-air temperature range
High-level input voltage
2
• DALLAS, TEXAS 75265
V
V
0.8
V
VCC
VCC
V
0
10
ns
–55
125
°C
Input rise and fall slew rate
POST OFFICE BOX 655303
UNIT
V
CD74ACT297
DIGITAL PHASE-LOCKED LOOP
SCHS297D – AUGUST 1998 – REVISED JUNE 2002
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
VOH
VOL
TEST CONDITIONS
VI = VIH or VIL
VI =VIH or VIL
VCC
TA = 25°C
MIN
MAX
MIN
MAX
IO = –50 µA
IO = –24 mA
4.5 V
4.4
4.4
4.5 V
3.4
3.1
IO = –75 mA
IO = 50 µA
5.5 V
4.5 V
0.1
0.1
IO = 24 mA
IO = 75 mA†
4.5 V
0.9
1.1
UNIT
V
3.3
5.5 V
V
2.9
II
ICC (MSI)
VI = VCC or GND
VI = VCC or GND
5.5 V
±0.1
±1
5.5 V
8
80
ICC (SSI/FF)
VI = VCC or GND
5.5 V
4
40
mA
mA
mA
DICC
VI = VCC –2.1 V
4.5 V to 5.5 V
2.4
2.8
mA
† Test one output at a time for a 1-second maximum duration. Measurement is made by forcing current and measuring voltage to minimize power
dissipation. Test verifies a minimum 50-Ω transmission-line drive capability at 85°C.
ACT INPUT LOAD
UNIT
LOAD†
INPUT
ENCTR, D/U
0.1
A, B, C, D, K CLK, φA2
0.2
I/D CLK, φA1, φB
0.5
† Unit Load is ∆ICC limit specified in
electrical characteristics table (e.g.,
2.4 mA at 25°C).
timing requirements over recommended supply-voltage range and recommended operating
free-air temperature range (unless otherwise noted)
TA = 25°C
MIN
MAX
PARAMETER
fclock
l k
Clock frequency
tw
Pulse duration
tsu
Setup time before K CLK↑
th
Hold time after K CLK↑
POST OFFICE BOX 655303
MIN
MAX
K CLK
55
45
I/D CLK
40
35
K CLK
6
8
I/D CLK
7
9
D/U
13
17
ENCTR
12
16
D/U
3
7
ENCTR
2
6
• DALLAS, TEXAS 75265
UNIT
MHz
ns
ns
ns
7
CD74ACT297
DIGITAL PHASE-LOCKED LOOP
SCHS297D – AUGUST 1998 – REVISED JUNE 2002
Carry Pulse
(internal signal)
Borrow Pulse
(internal signal)
I/D CLK
I/D OUT
Figure 4. I/D OUT in Lock Condition
φB
φA2
ECPD OUT
Figure 5. Edge-Controlled Phase-Comparator Waveforms
φB
φA1
XORPD OUT
Figure 6. Exclusive-OR Phase-Detector Waveforms
1/F max
tw
I/D CLK
3V
1.5 V
1.5 V
0V
tPHL
I/D OUT
tPHL
≈VCC
90%
10%
tTLH
50% VCC
50% VCC
VOL
tTHL
Figure 7. Clock (ID CLK) to Output (ID OUT) Propagation Delays,
Clock Pulse Duration, and Maximum Clock-Pulse Frequency
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
CD74ACT297
DIGITAL PHASE-LOCKED LOOP
SCHS297D – AUGUST 1998 – REVISED JUNE 2002
3V
φB
1.5 V
1.5 V
0V
tPHL
3V
φA1
1.5 V
1.5 V
0V
tPLH
tPHL
≈VCC
50% VCC
50% VCC
50% VCC
50% VCC
VOL
XORPD OUT
tPLH
Figure 8. Phase Input (φB, φA2) to Output (XORPD OUT) Propagation Delays
3V
φB
1.5 V
1.5 V
0V
3V
1.5 V
φA2
0V
≈VCC
50% VCC
ECPD OUT
50% VCC
VOL
tPHL
tPLH
Figure 9. Phase Input (φB, φA2) to Output (ECPD OUT) Propagation Delays
ÎÎÎÎÎ
ÏÏ ÎÎÎÎÎ
ÏÏÏÏ
ÏÏ ÎÎÎÎÎ ÏÏÏÏ
tH
D/U
ENCTR
tH
1.5 V
1.5 V
1.5 V
1.5 V
3V
(See Note A)
0V
tsu
tsu
3V
K CLK
1.5 V
1.5 V
1.5 V
0V
tw
1/fmax
NOTE A: Shaded areas indicate when the input is permitted to change for predictable output performance.
Figure 10. Clock (K CLK) Pulse Duration and Maximum Clock-Pulse Frequency,
and Inputs (D/U, ENCTR) to Clock (K CLK) Setup and Hold Times
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
CD74ACT297
DIGITAL PHASE-LOCKED LOOP
SCHS297D – AUGUST 1998 – REVISED JUNE 2002
switching characteristics over recommended operating free-air temperature range, CL = 50 pF
(unless otherwise noted)
PARAMETER
fmax
tPLH
tPHL
tPHL
tPLH
tPHL
tPLH
tPHL
tPLH
10
FROM
(INPUT)
TO
(OUTPUT)
K CLK
I/D OUT
I/D CLK
I/D CLK
I/D OUT
φA2
ECPD OUT
φA1
XORPD OUT
φB
XORPD OUT
φB
ECPD OUT
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MIN
TA = 25°C
TYP
MAX
MIN
55
45
40
35
MAX
UNIT
MHz
19
24
19
24
24
30
17
22
17
22
17
22
17
22
24
30
ns
ns
ns
ns
ns
CD74ACT297
DIGITAL PHASE-LOCKED LOOP
SCHS297D – AUGUST 1998 – REVISED JUNE 2002
PARAMETER MEASUREMENT INFORMATION
2 × VCC
S1
500 Ω
From Output
Under Test
Open
GND
CL = 50 pF
(see Note A)
500 Ω
TEST
S1
tPLH/tPHL
tPLZ/tPZL
tPHZ/tPZH
Open
2 × VCC
GND
LOAD CIRCUIT
3V
1.5 V
Timing Input
tw
90%
1.5 V
Input
3V
90%
1.5 V
10%
10%
tr
tf
tsu
3V
0V
1.5 V
Data Input
3V
1.5 V
1.5 V
0V
tPHL
tPLH
In-Phase
Output
50% VCC
Out-of-Phase
Output
VOH
50% VCC
VOL
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
Output
Control
(low-level
enabling)
Output
Waveform 1
S1 at 2 × VCC
(see Note B)
50% VCC
3V
1.5 V
1.5 V
0V
tPZL
tPLZ
50% VCC
tPZH
tPLH
tPHL
1.5 V
0V
VOLTAGE WAVEFORMS
INPUT RISE AND FALL TIMES AND PULSE DURATION
Input
0V
th
VOH
50% VCC
VOL
Output
Waveform 2
S1 at GND
(see Note B)
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
≈VCC
20% VCC
VOL
tPHZ
50% VCC
80% VCC
VOH
≈0 V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr = 3 ns, tf = 3 ns.
D. The outputs are measured one at a time with one input transition per measurement.
Figure 11. Load Circuit and Voltage Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
PACKAGE OPTION ADDENDUM
www.ti.com
10-Jun-2014
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
CD74ACT297M
ACTIVE
SOIC
D
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-55 to 125
ACT297M
CD74ACT297M96
ACTIVE
SOIC
D
16
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-55 to 125
ACT297M
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
10-Jun-2014
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Mar-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
CD74ACT297M96
Package Package Pins
Type Drawing
SOIC
D
16
SPQ
Reel
Reel
Diameter Width
(mm) W1 (mm)
2500
330.0
16.4
Pack Materials-Page 1
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
6.5
10.3
2.1
8.0
W
Pin1
(mm) Quadrant
16.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Mar-2008
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
CD74ACT297M96
SOIC
D
16
2500
333.2
345.9
28.6
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated