TI1 ADC12C105CISQ/NOPB 95/105 msps a/d converter Datasheet

ADC12C105
www.ti.com
SNAS417C – MAY 2007 – REVISED APRIL 2013
ADC12C105 12-Bit, 95/105 MSPS A/D Converter
Check for Samples: ADC12C105
FEATURES
DESCRIPTION
•
•
The ADC12C105 is a high-performance CMOS
analog-to-digital converter capable of converting
analog input signals into 12-bit digital words at rates
up to 105 Mega Samples Per Second (MSPS). This
converter uses a differential, pipelined architecture
with digital error correction and an on-chip sampleand-hold circuit to minimize power consumption and
the external component count, while providing
excellent dynamic performance. A unique sampleand-hold stage yields a full-power bandwidth of 1
GHz. The ADC12C105 may be operated from a
single +3.0V or +3.3V power supply and consumes
low power.
1
2
•
•
•
•
•
•
1 GHz Full Power Bandwidth
Internal Reference and Sample-and-Hold
Circuit
Low Power Consumption
Data Ready Output Clock
Clock Duty Cycle Stabilizer
Single +3.0V or +3.3V Supply Operation
Power-Down Mode
32-Pin WQFN Package, (5x5x0.8mm, 0.5mm
Pin-Pitch)
APPLICATIONS
•
•
•
•
•
High IF Sampling Receivers
Wireless Base Station Receivers
Test and Measurement Equipment
Communications Instrumentation
Portable Instrumentation
KEY SPECIFICATIONS
•
•
•
•
•
•
Resolution: 12 Bits
Conversion Rate: 105 MSPS
SNR: (fIN = 240 MHz) 69 dBFS (typ)
SFDR: (fIN = 240 MHz) 82 dBFS (typ)
Full Power Bandwidth: 1 GHz (typ)
Power Consumption:
– 350 mW (typ), VA=3.0 V
– 400 mW (typ), VA=3.3 V
A separate +2.5V supply may be used for the digital
output interface which allows lower power operation
with reduced noise. A power-down feature reduces
the power consumption to very low levels while still
allowing fast wake-up time to full operation. The
differential inputs accept a 2V full scale differential
input swing. A stable 1.2V internal voltage reference
is provided, or the ADC12C105 can be operated with
an external 1.2V reference. Output data format (offset
binary versus 2's complement) and duty cycle
stabilizer are pin-selectable. The duty cycle stabilizer
maintains performance over a wide range of clock
duty cycles.
The ADC12C105 is available in a 32-lead WQFN
package and operates over the industrial temperature
range of −40°C to +85°C.
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2007–2013, Texas Instruments Incorporated
ADC12C105
SNAS417C – MAY 2007 – REVISED APRIL 2013
www.ti.com
VRN
VRP
VA
AGND
VIN+
VIN-
D8
D10
D9
D11 (MSB)
PD
D7
25
26
27
28
29
VREF
30
1
24
2
23
3
22
4
ADC12C105
5
6
(Top View)
7
8
*
D6
D5
DRGND
21
DRDY
VDR
20
19
D4
18
D3
17
D2
9
AGND
10
VA
11
CLK
12
OF/DCS
13
N/C
14
N/C
15
D0
16
D1
AGND
VA
31
32
VCMO
Connection Diagram
Block Diagram
VIN+
S/H
VIN-
Stage
1
Stage
2
Stage
3
Stage
n
Stage
9
Stage
10
Stage
11
3
3
2
2
2
2
2
VA
AGND
PD
Timing
Control
24
11-Stage Pipeline Converter
3
VD
Digital Correction
DGND
OF/DCS
14
12
Output
Buffers
Duty
Cycle
Stabilizer
CLK
D0 - D11
DRDY
DRGND
VDR
VREF
Internal
reference
driver
Bandgap
reference
VRP
VCMO
VRN
2
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: ADC12C105
ADC12C105
www.ti.com
SNAS417C – MAY 2007 – REVISED APRIL 2013
Pin Descriptions and Equivalent Circuits
Pin No.
Symbol
Equivalent Circuit
Description
ANALOG I/O
5
VIN+
VA
6
Differential analog input pins. The differential full-scale input signal
level is 2VP-P with each input pin signal centered on a common mode
voltage, VCM.
VIN-
AGND
2
VRP
32
VCMO
VA
VA
VA
1
VRN
VA
These pins should each be bypassed to AGND with a low ESL
(equivalent series inductance) 0.1 µF capacitor placed very close to
the pin to minimize stray inductance. A 0.1 µF capacitor should be
placed between VRP and VRN as close to the pins as possible, and a
1 µF capacitor should be placed in parallel.
VRP and VRN should not be loaded. VCMO may be loaded to 1mA for
use as a temperature stable 1.5V reference.
It is recommended to use VCMO to provide the common mode
voltage, VCM, for the differential analog inputs, VIN+ and VIN−.
AGND
AGND
VA
31
Reference Voltage. This device provides an internally developed
1.2V reference. When using the internal reference, VREF should be
decoupled to AGND with a 0.1 µF and a 1 µF low equivalent series
inductance (ESL) capacitor .
This pin may be driven with an external 1.2V reference voltage.
This pin should not be used to source or sink current.
VREF
AGND
VA
12
OF/DCS
AGND
This is a four-state pin controlling the input clock mode and output
data format.
OF/DCS = VA, output data format is 2's complement without duty
cycle stabilization applied to the input clock
OF/DCS = AGND, output data format is offset binary, without duty
cycle stabilization applied to the input clock.
OF/DCS = (2/3)*VA, output data is 2's complement with duty cycle
stabilization applied to the input clock
OF/DCS = (1/3)*VA, output data is offset binary with duty cycle
stabilization applied to the input clock.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: ADC12C105
3
ADC12C105
SNAS417C – MAY 2007 – REVISED APRIL 2013
www.ti.com
Pin Descriptions and Equivalent Circuits (continued)
Pin No.
Symbol
Equivalent Circuit
Description
DIGITAL I/O
11
CLK
VA
30
The clock input pin.
The analog input is sampled on the rising edge of the clock input.
This is a two-state input controlling Power Down.
PD = VA, Power Down is enabled and power dissipation is reduced.
PD = AGND, Normal operation.
PD
AGND
15-19,
23-29
D0–D11
21
DRDY
VDR
Digital data output pins that make up the 12-bit conversion result. D0
(pin 15) is the LSB, while D11 (pin 29) is the MSB of the output
word. Output levels are CMOS compatible.
Data Ready Strobe. The data output transition is synchronized with
the falling edge of this signal. This signal switches at the same
frequency as the CLK input.
DRGND
13, 14
VA
DGND
NC
No internal connection
3, 8, 10
VA
Positive analog supply pins. These pins should be connected to a
quiet voltage source and be bypassed to AGND with 0.1 µF
capacitors located close to the power pins.
4, 7, 9,
Exposed Pad
AGND
The ground return for the analog supply.
The exposed pad on back of package must be soldered to ground
plane to ensure rated performance.
20
VDR
Positive driver supply pin for the output drivers. This pin should be
connected to a quiet voltage source and be bypassed to DRGND
with a 0.1 µF capacitor located close to the power pin.
22
DRGND
ANALOG POWER
DIGITAL POWER
4
The ground return for the digital output driver supply. This pins
should be connected to the system digital ground, but not be
connected in close proximity to the ADC's AGND pins.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: ADC12C105
ADC12C105
www.ti.com
SNAS417C – MAY 2007 – REVISED APRIL 2013
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings (1) (2) (3)
−0.3V to 4.2V
Supply Voltage (VA, VDR)
−0.3V to (VA +0.3V)
Voltage on Any Pin
(Not to exceed 4.2V)
Input Current at Any Pin other than Supply Pins
Package Input Current
(4)
±5 mA
(4)
±50 mA
Max Junction Temp (TJ)
Thermal Resistance (θJA)
+150°C
(5)
30°C/W
Human Body Model
ESD Rating
Machine Model
(6)
2500V
(6)
250V
−65°C to +150°C
Storage Temperature
Soldering process must comply with TI's Reflow Temperature Profile specifications. Refer to www.ti.com/packaging. (7)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
All voltages are measured with respect to GND = AGND = DRGND = 0V, unless otherwise specified.
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is specified to be functional, but do not ensure specific performance limits. For ensured specifications and test
conditions, see the Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance
characteristics may degrade when the device is not operated under the listed test conditions. Operation of the device beyond the
maximum Operating Ratings is not recommended.
If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications.
When the input voltage at any pin exceeds the power supplies (that is, VIN < AGND, or VIN > VA), the current at that pin should be
limited to ±5 mA. The ±50 mA maximum package input current rating limits the number of pins that can safely exceed the power
supplies with an input current of ±5 mA to 10.
The maximum allowable power dissipation is dictated by TJ,max, the junction-to-ambient thermal resistance, (θJA), and the ambient
temperature, (TA), and can be calculated using the formula PD,max = (TJ,max - TA )/θJA. The values for maximum power dissipation listed
above will be reached only when the device is operated in a severe fault condition (e.g. when input or output pins are driven beyond the
power supply voltages, or the power supply polarity is reversed). Such conditions should always be avoided.
Human Body Model is 100 pF discharged through a 1.5 kΩ resistor. Machine Model is 220 pF discharged through 0 Ω
Reflow temperature profiles are different for lead-free and non-lead-free packages.
Operating Ratings
(1) (2)
−40°C ≤ TA ≤ +85°C
Operating Temperature
Supply Voltage (VA)
+2.7V to +3.6V
Output Driver Supply (VDR)
Clock Duty Cycle
+2.4V to VA
(DCS Enabled)
(DCS disabled)
VCM
(2)
45/55 %
1.4V to 1.6V
≤100mV
|AGND-DRGND|
(1)
30/70 %
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is specified to be functional, but do not ensure specific performance limits. For ensured specifications and test
conditions, see the Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance
characteristics may degrade when the device is not operated under the listed test conditions. Operation of the device beyond the
maximum Operating Ratings is not recommended.
All voltages are measured with respect to GND = AGND = DRGND = 0V, unless otherwise specified.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: ADC12C105
5
ADC12C105
SNAS417C – MAY 2007 – REVISED APRIL 2013
www.ti.com
Converter Electrical Characteristics
Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.3V, VDR = +2.5V, Internal VREF
= +1.2V, fCLK = 105 MHz, 50% Duty Cycle, DCS disabled, VCM = VCMO, CL = 5 pF/pin. Typical values are for TA = 25°C.
Boldface limits apply for TMIN ≤ TA ≤ TMAX. All other limits apply for TA = 25°C (1) (2)
Symbol
Parameter
Conditions
Typical
(3)
Limits
Units
(Limits)
STATIC CONVERTER CHARACTERISTICS
Resolution with No Missing Codes
INL
Integral Non Linearity
±0.5
12
Bits (min)
1.2
LSB (max)
-1.2
LSB (min)
0.7
LSB (max)
DNL
Differential Non Linearity
±0.35
-0.6
LSB (min)
PGE
Positive Gain Error
-0.35
±1.25
%FS (max)
NGE
Negative Gain Error
-0.2
±1.25
%FS (max)
TC PGE
Positive Gain Error Tempco
−40°C ≤ TA ≤ +85°C
-3
TC NGE
Negative Gain Error Tempco
−40°C ≤ TA ≤ +85°C
-7
VOFF
Offset Error (VIN+ = VIN-)
TC VOFF
Offset Error Tempco
0.065
−40°C ≤ TA ≤ +85°C
ppm/°C
ppm/°C
±0.55
-4
%FS (max)
ppm/°C
Under Range Output Code
0
0
Over Range Output Code
4095
4095
REFERENCE AND ANALOG INPUT CHARACTERISTICS
VCMO
Common Mode Output Voltage
1.5
1.4
1.56
V (min)
V (max)
VCM
Analog Input Common Mode Voltage
1.5
1.4
1.6
V (min)
V (max)
VIN Input Capacitance (each pin to GND)
CIN
(4)
VREF
Internal Reference Voltage
TC VREF
Internal Reference Voltage Tempco
VIN = 1.5 Vdc ± 0.5
V
(CLK LOW)
8.5
pF
(CLK HIGH)
3.5
pF
1.18
V
−40°C ≤ TA ≤ +85°C
18
ppm/°C
VRP
Internal Reference top
1.98
1.89
2.06
VRN
Internal Reference bottom
0.98
0.89
1.06
V (min)
V (max)
Ext VREF
External Reference Voltage
1.20
1.176
1.224
V (min)
V (max)
(1)
V (min)
V (max)
The inputs are protected as shown below. Input voltage magnitudes above VA or below GND will not damage this device, provided
current is limited per Absolute Maximum Ratings, Note 4. However, errors in the A/D conversion can occur if the input goes above 2.6V
or below GND as described in the Operating Ratings section.
VA
I/O
To Internal Circuitry
AGND
(2)
(3)
(4)
6
With a full scale differential input of 2VP-P , the 12-bit LSB is 488 µV.
Typical figures are at TA = 25°C and represent most likely parametric norms at the time of product characterization. The typical
specifications are not ensured.
The input capacitance is the sum of the package/pin capacitance and the sample and hold circuit capacitance.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: ADC12C105
ADC12C105
www.ti.com
SNAS417C – MAY 2007 – REVISED APRIL 2013
Dynamic Converter Electrical Characteristics
Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.3V, VDR = +2.5V, Internal VREF
= +1.2V, fCLK = 105 MHz, 50% Duty Cycle, DCS disabled, VCM = VCMO, CL = 5 pF/pin, . Typical values are for TA = 25°C.
Boldface limits apply for TMIN ≤ TA ≤ TMAX. All other limits apply for TA = 25°C (1) (2)
Symbol
Parameter
Conditions
Typical
(3)
Limits
Units
(Limits) (4)
DYNAMIC CONVERTER CHARACTERISTICS, AIN= -1dBFS
FPBW
SNR
SFDR
ENOB
THD
H2
Signal-to-Noise Ratio
Spurious Free Dynamic Range
Effective Number of Bits
Total Harmonic Disortion
Second Harmonic Distortion
H3
Third Harmonic Distortion
SINAD
IMD
(1)
Full Power Bandwidth
Signal-to-Noise and Distortion Ratio
Intermodulation Distortion
-1 dBFS Input, −3 dB Corner
1.0
GHz
fIN = 10 MHz
71
dBFS
fIN = 70 MHz
70.5
fIN = 240 MHz
69
fIN = 10 MHz
90
fIN = 70 MHz
86
fIN = 240 MHz
82
fIN = 10 MHz
11.5
fIN = 70 MHz
11.3
fIN = 240 MHz
11.1
fIN = 10 MHz
−86
fIN = 70 MHz
−85
fIN = 240 MHz
−80
fIN = 10 MHz
−95
fIN = 70 MHz
−90
fIN = 240 MHz
−86
fIN = 10 MHz
−90
fIN = 70 MHz
−86
fIN = 240 MHz
−82
fIN = 10 MHz
70.8
fIN = 70 MHz
70
fIN = 240 MHz
68.6
fIN = 19.5 MHz and 20.5MHz,
each -7 dBFS
-82
dBFS
68.3
dBFS
dBFS
dBFS
78
dBFS
Bits
Bits
10.9
Bits
dBFS
dBFS
-74
dBFS
dBFS
dBFS
-78
dBFS
dBFS
dBFS
-78
dBFS
dBFS
dBFS
67.4
dBFS
dBFS
The inputs are protected as shown below. Input voltage magnitudes above VA or below GND will not damage this device, provided
current is limited per Absolute Maximum Ratings, Note 4. However, errors in the A/D conversion can occur if the input goes above 2.6V
or below GND as described in the Operating Ratings section.
VA
I/O
To Internal Circuitry
AGND
(2)
(3)
(4)
With a full scale differential input of 2VP-P , the 12-bit LSB is 488 µV.
Typical figures are at TA = 25°C and represent most likely parametric norms at the time of product characterization. The typical
specifications are not ensured.
Parameters specified in dBFS indicate the value that would be attained with a full-scale input signal.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: ADC12C105
7
ADC12C105
SNAS417C – MAY 2007 – REVISED APRIL 2013
www.ti.com
Logic and Power Supply Electrical Characteristics
Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.3V, VDR = +2.5V, Internal VREF
= +1.2V, fCLK = 105 MHz, 50% Duty Cycle, DCS disabled, VCM = VCMO, CL = 5 pF/pin. Typical values are for TA = 25°C.
Boldface limits apply for TMIN ≤ TA ≤ TMAX. All other limits apply for TA = 25°C (1) (2)
Symbol
Parameter
Conditions
Typical
(3)
Limits
Units
(Limits)
DIGITAL INPUT CHARACTERISTICS (CLK, PD)
VIN(1)
Logical “1” Input Voltage
VD = 3.6V
2.0
V (min)
VIN(0)
Logical “0” Input Voltage
VD = 3.0V
0.8
V (max)
IIN(1)
Logical “1” Input Current
VIN = 3.3V
10
µA
IIN(0)
Logical “0” Input Current
VIN = 0V
−10
µA
CIN
Digital Input Capacitance
5
pF
DIGITAL OUTPUT CHARACTERISTICS (D0–D13, DRDY)
VOUT(1)
Logical “1” Output Voltage
IOUT = −0.5 mA , VDR = 2.4V
VOUT(0)
Logical “0” Output Voltage
IOUT = 1.6 mA, VDR = 2.4V
+ISC
Output Short Circuit Source Current
VOUT = 0V
−10
mA
−ISC
Output Short Circuit Sink Current
VOUT = VDR
10
mA
COUT
Digital Output Capacitance
5
pF
2.0
V (min)
0.4
V (max)
POWER SUPPLY CHARACTERISTICS
IA
Analog Supply Current
Full Operation
IDR
Digital Output Supply Current
Full Operation
(1)
121
(4)
141
16
Power Consumption
Excludes IDR
(4)
400
Power Down Power Consumption
Clock disabled
7.5
mA (max)
mA
466
mW (max)
mW
The inputs are protected as shown below. Input voltage magnitudes above VA or below GND will not damage this device, provided
current is limited per Absolute Maximum Ratings, Note 4. However, errors in the A/D conversion can occur if the input goes above 2.6V
or below GND as described in the Operating Ratings section.
VA
I/O
To Internal Circuitry
AGND
(2)
(3)
(4)
8
With a full scale differential input of 2VP-P , the 12-bit LSB is 488 µV.
Typical figures are at TA = 25°C and represent most likely parametric norms at the time of product characterization. The typical
specifications are not ensured.
IDR is the current consumed by the switching of the output drivers and is primarily determined by load capacitance on the output pins,
the supply voltage, VDR, and the rate at which the outputs are switching (which is signal dependent). IDR=VDR(C0 x f0 + C1 x f1 +....C11 x
f11) where VDR is the output driver power supply voltage, Cn is total capacitance on the output pin, and fn is the average frequency at
which that pin is toggling.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: ADC12C105
ADC12C105
www.ti.com
SNAS417C – MAY 2007 – REVISED APRIL 2013
Timing and AC Characteristics
Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.3V, VDR = +2.5V, Internal VREF
= +1.2V, fCLK = 105 MHz, 50% Duty Cycle, DCS disabled, VCM = VCMO, CL = 5 pF/pin. Typical values are for TA = 25°C.
Timing measurements are taken at 50% of the signal amplitude. Boldface limits apply for TMIN ≤ TA ≤ TMAX. All other limits
apply for TA = 25°C (1) (2)
Limits
Units
(Limits)
Maximum Clock Frequency
105
MHz (max)
Minimum Clock Frequency
20
MHz (min)
Symb
Parameter
Conditions
Typical
(3)
tCH
Clock High Time
4
tCL
Clock Low Time
4
tCONV
Conversion Latency
tOD
Output Delay of CLK to DATA
Relative to rising edge of CLK (4)
tSU
Data Output Setup Time
tH
Data Output Hold Time
tAD
Aperture Delay
0.6
ns
tAJ
Aperture Jitter
0.1
ps rms
(1)
ns
ns
7
Clock Cycles
5.76
3
7.3
ns (min)
ns (max)
Relative to DRDY
4.5
3.7
ns (min)
Relative to DRDY
4.5
3.8
ns (min)
The inputs are protected as shown below. Input voltage magnitudes above VA or below GND will not damage this device, provided
current is limited per Absolute Maximum Ratings, Note 4. However, errors in the A/D conversion can occur if the input goes above 2.6V
or below GND as described in the Operating Ratings section.
VA
I/O
To Internal Circuitry
AGND
(2)
(3)
(4)
With a full scale differential input of 2VP-P , the 12-bit LSB is 488 µV.
Typical figures are at TA = 25°C and represent most likely parametric norms at the time of product characterization. The typical
specifications are not ensured.
This parameter is specified by design and/or characterization and is not tested in production.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: ADC12C105
9
ADC12C105
SNAS417C – MAY 2007 – REVISED APRIL 2013
www.ti.com
Dynamic Converter Electrical Characteristics at 95MSPS
Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.3V, VDR = +2.5V, Internal VREF
= +1.2V, fCLK = 95 MHz, 50% Duty Cycle, DCS disabled, VCM = VCMO, CL = 5 pF/pin, . Typical values are for TA = 25°C.
Boldface limits apply for TMIN ≤ TA ≤ TMAX. All other limits apply for TA = 25°C (1) (2)
Symbol
Parameter
Conditions
Typical
(3)
Limits
Units
(Limits) (4)
DYNAMIC CONVERTER CHARACTERISTICS, AIN= -1dBFS
SNR
SFDR
ENOB
THD
H2
fIN = 10 MHz
71
dBFS
fIN = 70 MHz
70.5
dBFS
fIN = 240 MHz
69
dBFS
fIN = 10 MHz
90
dBFS
Signal-to-Noise Ratio
Spurious Free Dynamic Range
fIN = 70 MHz
86
dBFS
fIN = 240 MHz
82
dBFS
fIN = 10 MHz
11.5
Bits
Bits
Effective Number of Bits
fIN = 70 MHz
11.4
fIN = 240 MHz
11.1
Bits
fIN = 10 MHz
−88
dBFS
fIN = 70 MHz
−85
dBFS
fIN = 240 MHz
−80
dBFS
fIN = 10 MHz
-95
dBFS
fIN = 70 MHz
−90
dBFS
fIN = 240 MHz
−85
dBFS
fIN = 10 MHz
−90
dBFS
fIN = 70 MHz
−86
dBFS
fIN = 240 MHz
−82
dBFS
fIN = 10 MHz
70.9
dBFS
fIN = 70 MHz
70.35
dBFS
fIN = 240 MHz
68.7
dBFS
115
mA (max)
(5)
14.5
mA
380
mW (max)
Total Harmonic Disortion
Second Harmonic Distortion
H3
Third Harmonic Distortion
SINAD
Signal-to-Noise and Distortion Ratio
POWER SUPPLY CHARACTERISTICS
IA
Analog Supply Current
Full Operation
IDR
Digital Output Supply Current
Full Operation
Power Consumption
(1)
Excludes IDR
(5)
The inputs are protected as shown below. Input voltage magnitudes above VA or below GND will not damage this device, provided
current is limited per Absolute Maximum Ratings, Note 4. However, errors in the A/D conversion can occur if the input goes above 2.6V
or below GND as described in the Operating Ratings section.
VA
I/O
To Internal Circuitry
AGND
(2)
(3)
(4)
(5)
10
With a full scale differential input of 2VP-P , the 12-bit LSB is 488 µV.
Typical figures are at TA = 25°C and represent most likely parametric norms at the time of product characterization. The typical
specifications are not ensured.
Parameters specified in dBFS indicate the value that would be attained with a full-scale input signal.
IDR is the current consumed by the switching of the output drivers and is primarily determined by load capacitance on the output pins,
the supply voltage, VDR, and the rate at which the outputs are switching (which is signal dependent). IDR=VDR(C0 x f0 + C1 x f1 +....C11 x
f11) where VDR is the output driver power supply voltage, Cn is total capacitance on the output pin, and fn is the average frequency at
which that pin is toggling.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: ADC12C105
ADC12C105
www.ti.com
SNAS417C – MAY 2007 – REVISED APRIL 2013
Specification Definitions
APERTURE DELAY is the time after the falling edge of the clock to when the input signal is acquired or held for
conversion.
APERTURE JITTER (APERTURE UNCERTAINTY) is the variation in aperture delay from sample to sample.
Aperture jitter manifests itself as noise in the output.
CLOCK DUTY CYCLE is the ratio of the time during one cycle that a repetitive digital waveform is high to the
total time of one period. The specification here refers to the ADC clock input signal.
COMMON MODE VOLTAGE (VCM) is the common DC voltage applied to both input terminals of the ADC.
CONVERSION LATENCY is the number of clock cycles between initiation of conversion and when that data is
presented to the output driver stage. Data for any given sample is available at the output pins the Pipeline Delay
plus the Output Delay after the sample is taken. New data is available at every clock cycle, but the data lags the
conversion by the pipeline delay.
DIFFERENTIAL NON-LINEARITY (DNL) is the measure of the maximum deviation from the ideal step size of 1
LSB.
EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE BITS) is another method of specifying Signal-to-Noise
and Distortion Ratio or SINAD. ENOB is defined as (SINAD - 1.76) / 6.02 and says that the converter is
equivalent to a perfect ADC of this (ENOB) number of bits.
FULL POWER BANDWIDTH is a measure of the frequency at which the reconstructed output fundamental
drops 3 dB below its low frequency value for a full scale input.
GAIN ERROR is the deviation from the ideal slope of the transfer function. It can be calculated as:
Gain Error = Positive Full Scale Error − Negative Full Scale Error
(1)
It can also be expressed as Positive Gain Error and Negative Gain Error, which are calculated as:
PGE = Positive Full Scale Error - Offset Error NGE = Offset Error - Negative Full Scale Error
(2)
INTEGRAL NON LINEARITY (INL) is a measure of the deviation of each individual code from a best fit straight
line. The deviation of any given code from this straight line is measured from the center of that code value.
INTERMODULATION DISTORTION (IMD) is the creation of additional spectral components as a result of two
sinusoidal frequencies being applied to the ADC input at the same time. It is defined as the ratio of the power in
the intermodulation products to the total power in the original frequencies. IMD is usually expressed in dBFS.
LSB (LEAST SIGNIFICANT BIT) is the bit that has the smallest value or weight of all bits. This value is VFS/2n,
where “VFS” is the full scale input voltage and “n” is the ADC resolution in bits.
MISSING CODES are those output codes that will never appear at the ADC outputs. The ADC12C105 is
ensured not to have any missing codes.
MSB (MOST SIGNIFICANT BIT) is the bit that has the largest value or weight. Its value is one half of full scale.
NEGATIVE FULL SCALE ERROR is the difference between the actual first code transition and its ideal value of
½ LSB above negative full scale.
OFFSET ERROR is the difference between the two input voltages [(VIN+) – (VIN-)] required to cause a transition
from code 2047 to 2048.
OUTPUT DELAY is the time delay after the falling edge of the clock before the data update is presented at the
output pins.
PIPELINE DELAY (LATENCY) See CONVERSION LATENCY.
POSITIVE FULL SCALE ERROR is the difference between the actual last code transition and its ideal value of
1½ LSB below positive full scale.
POWER SUPPLY REJECTION RATIO (PSRR) is a measure of how well the ADC rejects a change in the power
supply voltage. PSRR is the ratio of the Full-Scale output of the ADC with the supply at the minimum DC supply
limit to the Full-Scale output of the ADC with the supply at the maximum DC supply limit, expressed in dB.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: ADC12C105
11
ADC12C105
SNAS417C – MAY 2007 – REVISED APRIL 2013
www.ti.com
SIGNAL TO NOISE RATIO (SNR) is the ratio, expressed in dB, of the rms value of the input signal to the rms
value of the sum of all other spectral components below one-half the sampling frequency, not including
harmonics or DC.
SIGNAL TO NOISE PLUS DISTORTION (S/N+D or SINAD) Is the ratio, expressed in dB, of the rms value of the
input signal to the rms value of all of the other spectral components below half the clock frequency, including
harmonics but excluding d.c.
SPURIOUS FREE DYNAMIC RANGE (SFDR) is the difference, expressed in dB, between the rms values of the
input signal and the peak spurious signal, where a spurious signal is any signal present in the output spectrum
that is not present at the input.
TOTAL HARMONIC DISTORTION (THD) is the ratio, expressed in dB, of the rms total of the first six harmonic
levels at the output to the level of the fundamental at the output. THD is calculated as
(3)
where f1 is the RMS power of the fundamental (output) frequency and f2 through f7 are the RMS power of the first
six harmonic frequencies in the output spectrum.
SECOND HARMONIC DISTORTION (2ND HARM) is the difference expressed in dB, between the RMS power in
the input frequency at the output and the power in its 2nd harmonic level at the output.
THIRD HARMONIC DISTORTION (3RD HARM) is the difference, expressed in dB, between the RMS power in
the input frequency at the output and the power in its 3rd harmonic level at the output.
Timing Diagram
Sample N + 8
Sample N + 7
Sample N + 9
|
Sample N + 6
Sample N
Sample N + 10
VIN
tAD
Clock N
Clock N + 7
1
fCLK
|
CLK
tCL
tCH
|
Latency
tOD
|
DRDY
tSU
| |
D0 - D11
Data N - 1
tH
Data N
Data N + 1
Data N + 2
Figure 1. Output Timing
12
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: ADC12C105
ADC12C105
www.ti.com
SNAS417C – MAY 2007 – REVISED APRIL 2013
Transfer Characteristic
Figure 2. Transfer Characteristic
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: ADC12C105
13
ADC12C105
SNAS417C – MAY 2007 – REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics DNL, INL
Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.3V, VDR = +2.5V, Internal VREF
= +1.2V, fCLK = 105 MHz, 50% Duty Cycle, DCS disabled, VCM = VCMO, fIN = 10 MHz, CL = 5 pF/pin. Typical values are for TA
= 25°C.
14
DNL
INL
Figure 3.
Figure 4.
DNL vs. fCLK
INL vs. fCLK
Figure 5.
Figure 6.
DNL vs. Temperature
INL vs. Temperature
Figure 7.
Figure 8.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: ADC12C105
ADC12C105
www.ti.com
SNAS417C – MAY 2007 – REVISED APRIL 2013
Typical Performance Characteristics DNL, INL (continued)
Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.3V, VDR = +2.5V, Internal VREF
= +1.2V, fCLK = 105 MHz, 50% Duty Cycle, DCS disabled, VCM = VCMO, fIN = 10 MHz, CL = 5 pF/pin. Typical values are for TA
= 25°C.
DNL vs. VA
INL vs. VA
Figure 9.
Figure 10.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: ADC12C105
15
ADC12C105
SNAS417C – MAY 2007 – REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics
Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.3V, VDR = +2.5V, Internal VREF
= +1.2V, fCLK = 105 MHz, 50% Duty Cycle, DCS disabled, VCM = VCMO, fIN = 10 MHz, CL = 5 pF/pin. Typical values are for TA
= 25°C.
16
SNR, SINAD, SFDR vs. VA
Distortion vs. VA
Figure 11.
Figure 12.
SNR, SINAD, SFDR vs. VDR
Distortion vs. VDR
Figure 13.
Figure 14.
SNR, SINAD, SFDR vs. fCLK
Distortion vs. fCLK
Figure 15.
Figure 16.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: ADC12C105
ADC12C105
www.ti.com
SNAS417C – MAY 2007 – REVISED APRIL 2013
Typical Performance Characteristics (continued)
Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.3V, VDR = +2.5V, Internal VREF
= +1.2V, fCLK = 105 MHz, 50% Duty Cycle, DCS disabled, VCM = VCMO, fIN = 10 MHz, CL = 5 pF/pin. Typical values are for TA
= 25°C.
SNR, SINAD, SFDR vs. Clock Duty Cycle
Distortion vs. Clock Duty Cycle
Figure 17.
Figure 18.
SNR, SINAD, SFDR vs. Clock Duty Cycle, DCS Enabled
Distortion vs. Clock Duty Cycle, DCS Enabled
Figure 19.
Figure 20.
SNR, SINAD, SFDR vs. fIN
Distortion vs. fIN
Figure 21.
Figure 22.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: ADC12C105
17
ADC12C105
SNAS417C – MAY 2007 – REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics (continued)
Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.3V, VDR = +2.5V, Internal VREF
= +1.2V, fCLK = 105 MHz, 50% Duty Cycle, DCS disabled, VCM = VCMO, fIN = 10 MHz, CL = 5 pF/pin. Typical values are for TA
= 25°C.
18
SNR, SINAD, SFDR vs. Temperature
Distortion vs. Temperature
Figure 23.
Figure 24.
Spectral Response @ 10 MHz Input
Spectral Response @ 70 MHz Input
Figure 25.
Figure 26.
Spectral Response @ 240 MHz Input
Intermodulation Distortion, fIN1= 19.5 MHz, fIN2 = 20.5 MHz
Figure 27.
Figure 28.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: ADC12C105
ADC12C105
www.ti.com
SNAS417C – MAY 2007 – REVISED APRIL 2013
Typical Performance Characteristics (continued)
Unless otherwise specified, the following specifications apply: AGND = DRGND = 0V, VA = +3.3V, VDR = +2.5V, Internal VREF
= +1.2V, fCLK = 105 MHz, 50% Duty Cycle, DCS disabled, VCM = VCMO, fIN = 10 MHz, CL = 5 pF/pin. Typical values are for TA
= 25°C.
Power vs. fCLK
Figure 29.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: ADC12C105
19
ADC12C105
SNAS417C – MAY 2007 – REVISED APRIL 2013
www.ti.com
FUNCTIONAL DESCRIPTION
Operating on a single +3.3V supply, the ADC12C105 uses a pipeline architecture and has error correction
circuitry to help ensure maximum performance. The differential analog input signal is digitized to 12 bits. The
user has the choice of using an internal 1.2V stable reference, or using an external 1.2V reference. Any external
reference is buffered on-chip to ease the task of driving that pin.
The output word rate is the same as the clock frequency. The analog input is acquired at the rising edge of the
clock and the digital data for a given sample is delayed by the pipeline for 7 clock cycles. The digital outputs are
CMOS compatible signals that are clocked by a synchronous data ready output signal (DRDY, pin 21) at the
same rate as the clock input. Duty cycle stabilization and output data format are selectable using the quad state
function OF/DCS pin (pin 12). The output data can be set for offset binary or two's complement.
Power-down is selectable using the PD pin (pin 30). A logic high on the PD pin reduces the converter power
consumption. For normal operation, the PD pin should be connected to the analog ground (AGND).
Applications Information
OPERATING CONDITIONS
We recommend that the following conditions be observed for operation of the ADC12C105:
2.7V ≤ VA ≤ 3.6V
2.4V ≤ VDR ≤ VA
20 MHz ≤ fCLK ≤ 105 MHz
1.2V internal reference
VREF = 1.2V (for an external reference)
VCM = 1.5V (from VCMO)
ANALOG INPUTS
Signal Inputs
Differential Analog Input Pins
The ADC12C105 has one pair of analog signal input pins, VIN+ and VIN−, which form a differential input pair. The
input signal, VIN, is defined as
VIN = (VIN+) – (VIN−)
(4)
Figure 30 shows the expected input signal range. Note that the common mode input voltage, VCM, should be
1.5V. Using VCMO (pin 32) for VCM will ensure the proper input common mode level for the analog input signal.
The positive peaks of the individual input signals should each never exceed 2.6V. Each analog input pin of the
differential pair should have a maximum peak-to-peak voltage of 1V, be 180° out of phase with each other and
be centered around VCM.The peak-to-peak voltage swing at each analog input pin should not exceed the 1V or
the output data will be clipped.
Figure 30. Expected Input Signal Range
For single frequency sine waves the full scale error in LSB can be described as approximately
20
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: ADC12C105
ADC12C105
www.ti.com
SNAS417C – MAY 2007 – REVISED APRIL 2013
EFS = 4096 ( 1 - sin (90° + dev))
(5)
Where dev is the angular difference in degrees between the two signals having a 180° relative phase relationship
to each other (see Figure 31). For single frequency inputs, angular errors result in a reduction of the effective full
scale input. For complex waveforms, however, angular errors will result in distortion.
Figure 31. Angular Errors Between the Two Input Signals Will Reduce the Output Level or Cause
Distortion
It is recommended to drive the analog inputs with a source impedance less than 100Ω. Matching the source
impedance for the differential inputs will improve even ordered harmonic performance (particularly second
harmonic).
Table 1 indicates the input to output relationship of the ADC12C105.
Table 1. Input to Output Relationship
VIN
VIN
Binary Output
2’s Complement Output
VCM − VREF/2
VCM + VREF/2
0000 0000 0000
1000 0000 0000
VCM − VREF/4
VCM + VREF/4
0100 0000 0000
1100 0000 0000
VCM
VCM
1000 0000 0000
0000 0000 0000
VCM + VREF/4
VCM − VREF/4
1100 0000 0000
0100 0000 0000
VCM + VREF/2
VCM − VREF/2
1111 1111 1111
0111 1111 1111
+
−
Negative Full-Scale
Mid-Scale
Positive Full-Scale
Driving the Analog Inputs
The VIN+ and the VIN− inputs of the ADC12C105 have an internal sample-and-hold circuit which consists of an
analog switch followed by a switched-capacitor amplifier.
Figure 32 and Figure 32 show examples of single-ended to differential conversion circuits. The circuit in
Figure 32 works well for input frequencies up to approximately 70MHz, while the circuit in Figure 33 works well
above 70MHz.
VIN
0.1 PF ADT1-1WT
50:
20:
18 pF
ADC
Input
0.1 PF
0.1 PF
20:
VCMO
Figure 32. Low Input Frequency Transformer Drive Circuit
VIN
0.1 PF ETC1-1-13
25:
10 pF
0.1 PF
ETC1-1-13
ADC
Input
25:
VCMO
0.1 PF
Figure 33. High Input Frequency Transformer Drive Circuit
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: ADC12C105
21
ADC12C105
SNAS417C – MAY 2007 – REVISED APRIL 2013
www.ti.com
One short-coming of using a transformer to achieve the single-ended to differential conversion is that most RF
transformers have poor low frequency performance. A differential amplifier can be used to drive the analog inputs
for low frequency applications. The amplifier must be fast enough to settle from the charging glitches on the
analog input resulting from the sample-and-hold operation before the clock goes high and the sample is passed
to the ADC core.
The SFDR performance of the converter depends on the external signal conditioning circuity used, as this affects
how quickly the sample-and-hold charging glitch will settle. An external resistor and capacitor network as shown
in Figure 34 should be used to isolate the charging glitches at the ADC input from the external driving circuit and
to filter the wideband noise at the converter input. These components should be placed close to the ADC inputs
because the analog input of the ADC is the most sensitive part of the system, and this is the last opportunity to
filter that input. For Nyquist applications the RC pole should be at the ADC sample rate. The ADC input
capacitance in the sample mode should be considered when setting the RC pole. For wideband undersampling
applications, the RC pole should be set at least 1.5 to 2 times the maximum input frequency to maintain a linear
delay response.
Input Common Mode Voltage
The input common mode voltage, VCM, should be in the range of 1.4V to 1.6V and be a value such that the peak
excursions of the analog signal do not go more negative than ground or more positive than 2.6V. It is
recommended to use VCMO (pin 32) as the input common mode voltage.
If the ADC12C105 is operated with VA=3.6V, a resistor of approximately 1KΩ should be used from the VCMO pin
to AGND.This will help maintain stability over the entire temperature range when using a high supply voltage.
Reference Pins
The ADC12C105 is designed to operate with an internal or external 1.2V reference. The internal 1.2 Volt
reference is the default condition when no external reference input is applied to the VREF pin. If a voltage is
applied to the VREF pin, then that voltage is used for the reference. The VREF pin should always be bypassed to
ground with a 0.1 µF capacitor close to the reference input pin.
It is important that all grounds associated with the reference voltage and the analog input signal make connection
to the ground plane at a single, quiet point to minimize the effects of noise currents in the ground path.
The Reference Bypass Pins (VRP, VCMO, and VRN) are made available for bypass purposes. These pins should
each be bypassed to AGND with a low ESL (equivalent series inductance) 1 µF capacitor placed very close to
the pin to minimize stray inductance. A 0.1 µF capacitor should be placed between VRP and VRN as close to the
pins as possible, and a 1 µF capacitor should be placed in parallel. This configuration is shown in Figure 34. It is
necessary to avoid reference oscillation, which could result in reduced SFDR and/or SNR. VCMO may be loaded
to 1mA for use as a temperature stable 1.5V reference. The remaining pins should not be loaded.
Smaller capacitor values than those specified will allow faster recovery from the power down mode, but may
result in degraded noise performance. Loading any of these pins, other than VCMO may result in performance
degradation.
The nominal voltages for the reference bypass pins are as follows:
VCMO = 1.5 V
VRP = 2.0 V
VRN = 1.0 V
OF/DCS Pin
Duty cycle stabilization and output data format are selectable using this quad state function pin. When enabled,
duty cycle stabilization can compensate for clock inputs with duty cycles ranging from 30% to 70% and generate
a stable internal clock, improving the performance of the part. With OF/DCS = VA the output data format is 2's
complement and duty cycle stabilization is not used. With OF/DCS = AGND the output data format is offset
binary and duty cycle stabilization is not used. With OF/DCS = (2/3)*VA the output data format is 2's complement
and duty cycle stabilization is applied to the clock. If OF/DCS is (1/3)*VA the output data format is offset binary
and duty cycle stabilization is applied to the clock. While the sense of this pin may be changed "on the fly," doing
this is not recommended as the output data could be erroneous for a few clock cycles after this change is made.
22
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: ADC12C105
ADC12C105
www.ti.com
SNAS417C – MAY 2007 – REVISED APRIL 2013
DIGITAL INPUTS
Digital CMOS compatible inputs consist of CLK, and PD.
Clock Input
The CLK controls the timing of the sampling process. To achieve the optimum noise performance, the clock input
should be driven with a stable, low jitter clock signal in the range indicated in the Electrical Table. The clock input
signal should also have a short transition region. This can be achieved by passing a low-jitter sinusoidal clock
source through a high speed buffer gate. The trace carrying the clock signal should be as short as possible and
should not cross any other signal line, analog or digital, not even at 90°.
The clock signal also drives an internal state machine. If the clock is interrupted, or its frequency is too low, the
charge on the internal capacitors can dissipate to the point where the accuracy of the output data will degrade.
This is what limits the minimum sample rate.
The clock line should be terminated at its source in the characteristic impedance of that line. Take care to
maintain a constant clock line impedance throughout the length of the line. Refer to Application Note AN-905
(SNLA035) for information on setting characteristic impedance.
It is highly desirable that the the source driving the ADC clock pins only drive that pin. However, if that source is
used to drive other devices, then each driven pin should be AC terminated with a series RC to ground, such that
the resistor value is equal to the characteristic impedance of the clock line and the capacitor value is
(6)
where tPD is the signal propagation rate down the clock line, "L" is the line length and ZO is the characteristic
impedance of the clock line. This termination should be as close as possible to the ADC clock pin but beyond it
as seen from the clock source. Typical tPD is about 150 ps/inch (60 ps/cm) on FR-4 board material. The units of
"L" and tPD should be the same (inches or centimeters).
The duty cycle of the clock signal can affect the performance of the A/D Converter. Because achieving a precise
duty cycle is difficult, the ADC12C105 has a Duty Cycle Stabilizer. It is designed to maintain performance over a
clock duty cycle range of 30% to 70%.
Power-Down (PD)
The PD pin, when high, holds the ADC12C105 in a power-down mode to conserve power when the converter is
not being used. The power consumption in this state is 5 mW if the clock is stopped when PD is high. The output
data pins are undefined and the data in the pipeline is corrupted while in the power down mode.
The Power Down Mode Exit Cycle time is determined by the value of the components on pins 1, 2, and 32 and is
about 3 ms with the recommended components on the VRP, VCMO and VRN reference bypass pins. These
capacitors loose their charge in the Power Down mode and must be recharged by on-chip circuitry before
conversions can be accurate. Smaller capacitor values allow slightly faster recovery from the power down mode,
but can result in a reduction in SNR, SINAD and ENOB performance.
DIGITAL OUTPUTS
Digital outputs consist of the CMOS signals D0-D11, and DRDY.
The ADC12C105 has 13 CMOS compatible data output pins corresponding to the converted input value and a
data ready (DRDY) signal that should be used to capture the output data. Valid data is present at these outputs
while the PD pin is low. Data should be captured and latched with the rising edge of the DRDY signal.
Be very careful when driving a high capacitance bus. The more capacitance the output drivers must charge for
each conversion, the more instantaneous digital current flows through VDR and DRGND. These large charging
current spikes can cause on-chip ground noise and couple into the analog circuitry, degrading dynamic
performance. Adequate bypassing, limiting output capacitance and careful attention to the ground plane will
reduce this problem. The result could be an apparent reduction in dynamic performance.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: ADC12C105
23
ADC12C105
SNAS417C – MAY 2007 – REVISED APRIL 2013
www.ti.com
2.4 to VA Volts
+3.3V
CHOKE
2 x 0.1 PF
+
10 PF
31
1 PF
0.1 PF
32
0.1 PF
2
50
1 PF
20
10 PF
V DR
VA 3
VA 8
10
VA
0.1 PF
VREF
(MSB) D11
D10
D9
D8
VCMO
V RP
0.1 PF
0.1 PF
1
0.1 PF
0.1 PF
5
T1
18 pF
2
0.1 PF
0.1 PF
PD
OF/DCS
20
VIN+
VIN-
30
PD
12
OF/DCC
11
CLK
Clock In
4
7
9
AGND
AGND
ADT1-1WT
6
D4
D3
D2
D1
(LSB) D0
DRGND
1
20
DRDY
21
Output
Word
74LVTH162374
CLK
22
VIN
D7
D6
D5
ADC12C105
V RN
29
28
27
26
25
24
23
19
18
17
16
15
Figure 34. Application Circuit
POWER SUPPLY CONSIDERATIONS
The power supply pins should be bypassed with a 0.1 µF capacitor and with a 100 pF ceramic chip capacitor
close to each power pin. Leadless chip capacitors are preferred because they have low series inductance.
As is the case with all high-speed converters, the ADC12C105 is sensitive to power supply noise. Accordingly,
the noise on the analog supply pin should be kept below 100 mVP-P.
No pin should ever have a voltage on it that is in excess of the supply voltages, not even on a transient basis. Be
especially careful of this during power turn on and turn off.
The VDR pin provides power for the output drivers and may be operated from a supply in the range of 2.4V to VA.
This enables lower power operation, reduces the noise coupling effects from the digital outputs to the analog
circuitry and simplifies interfacing to lower voltage devices and systems.
LAYOUT AND GROUNDING
Proper grounding and proper routing of all signals are essential to ensure accurate conversion. Maintaining
separate analog and digital areas of the board, with the ADC12C105 between these areas, is required to achieve
specified performance.
The ground return for the data outputs (DRGND) carries the ground current for the output drivers. The output
current can exhibit high transients that could add noise to the conversion process. To prevent this from
happening, the DRGND pins should NOT be connected to system ground in close proximity to any of the
ADC12C105's other ground pins.
Capacitive coupling between the typically noisy digital circuitry and the sensitive analog circuitry can lead to poor
performance. The solution is to keep the analog circuitry separated from the digital circuitry, and to keep the
clock line as short as possible.
The effects of the noise generated from the ADC output switching can be minimized through the use of 22Ω
resistors in series with each data output line. Locate these resistors as close to the ADC output pins as possible.
Since digital switching transients are composed largely of high frequency components, total ground plane copper
weight will have little effect upon the logic-generated noise. This is because of the skin effect. Total surface area
is more important than is total ground plane area.
24
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: ADC12C105
ADC12C105
www.ti.com
SNAS417C – MAY 2007 – REVISED APRIL 2013
Generally, analog and digital lines should cross each other at 90° to avoid crosstalk. To maximize accuracy in
high speed, high resolution systems, however, avoid crossing analog and digital lines altogether. It is important to
keep clock lines as short as possible and isolated from ALL other lines, including other digital lines. Even the
generally accepted 90° crossing should be avoided with the clock line as even a little coupling can cause
problems at high frequencies. This is because other lines can introduce jitter into the clock line, which can lead to
degradation of SNR. Also, the high speed clock can introduce noise into the analog chain.
Best performance at high frequencies and at high resolution is obtained with a straight signal path. That is, the
signal path through all components should form a straight line wherever possible.
Be especially careful with the layout of inductors and transformers. Mutual inductance can change the
characteristics of the circuit in which they are used. Inductors and transformers should not be placed side by
side, even with just a small part of their bodies beside each other. For instance, place transformers for the analog
input and the clock input at 90° to one another to avoid magnetic coupling.
The analog input should be isolated from noisy signal traces to avoid coupling of spurious signals into the input.
Any external component (e.g., a filter capacitor) connected between the converter's input pins and ground or to
the reference input pin and ground should be connected to a very clean point in the ground plane.
All analog circuitry (input amplifiers, filters, reference components, etc.) should be placed in the analog area of
the board. All digital circuitry and dynamic I/O lines should be placed in the digital area of the board. The
ADC12C105 should be between these two areas. Furthermore, all components in the reference circuitry and the
input signal chain that are connected to ground should be connected together with short traces and enter the
ground plane at a single, quiet point. All ground connections should have a low inductance path to ground.
DYNAMIC PERFORMANCE
To achieve the best dynamic performance, the clock source driving the CLK input must have a sharp transition
region and be free of jitter. Isolate the ADC clock from any digital circuitry with buffers, as with the clock tree
shown in Figure 35. The gates used in the clock tree must be capable of operating at frequencies much higher
than those used if added jitter is to be prevented.
As mentioned in LAYOUT AND GROUNDING, it is good practice to keep the ADC clock line as short as possible
and to keep it well away from any other signals. Other signals can introduce jitter into the clock signal, which can
lead to reduced SNR performance, and the clock can introduce noise into other lines. Even lines with 90°
crossings have capacitive coupling, so try to avoid even these 90° crossings of the clock line.
Figure 35. Isolating the ADC Clock from other Circuitry with a Clock Tree
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: ADC12C105
25
ADC12C105
SNAS417C – MAY 2007 – REVISED APRIL 2013
www.ti.com
REVISION HISTORY
Changes from Revision B (April 2013) to Revision C
•
26
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 25
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: ADC12C105
PACKAGE OPTION ADDENDUM
www.ti.com
13-Sep-2014
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
ADC12C105CISQ/NOPB
ACTIVE
WQFN
RTV
32
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
-40 to 85
12C105
ADC12C105CISQE/NOPB
ACTIVE
WQFN
RTV
32
250
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
-40 to 85
12C105
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
13-Sep-2014
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
8-Apr-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
ADC12C105CISQ/NOPB
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
WQFN
RTV
32
1000
178.0
12.4
5.3
5.3
1.3
8.0
12.0
Q1
ADC12C105CISQE/NOPB WQFN
RTV
32
250
178.0
12.4
5.3
5.3
1.3
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
8-Apr-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
ADC12C105CISQ/NOPB
WQFN
RTV
32
1000
213.0
191.0
55.0
ADC12C105CISQE/NOPB
WQFN
RTV
32
250
213.0
191.0
55.0
Pack Materials-Page 2
MECHANICAL DATA
RTV0032A
SQA32A (Rev B)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated