HCTS160MS Radiation Hardened Synchronous Counter September 1995 Features • • • • • • • • • • • • • Pinouts 3 Micron Radiation Hardened SOS CMOS Total Dose 200K RAD (Si) SEP Effective LET No Upsets: >100 MEV-cm2/mg Single Event Upset (SEU) Immunity < 2 x 10-9 Errors/Bit-Day (Typ) Dose Rate Survivability: >1 x 1012 RAD (Si)/s Dose Rate Upset: >1010 RAD (Si)/s 20ns Pulse Latch-Up Free Under Any Conditions Fanout (Over Temperature Range) -Standard Outputs 10 LSTTL Loads Military Temperature Range: -55oC to +125oC Significant Power Reduction Compared to LSTTL ICs DC Operating Voltage Range: 4.5V to 5.5V LSTTL Input Compatibility -VIL = 0.8V Max -VIH = VCC/2 Min Input Current Levels Ii ≤ 5µA @ VOL, VOH 16 LEAD CERAMIC DUAL-IN-LINE METAL SEAL PACKAGE (SBDIP) MIL-STD-1835 CDIP2-T16 TOP VIEW 16 VCC CP 2 15 TC P0 3 14 Q0 P1 4 13 Q1 P2 5 12 Q2 P3 6 11 Q3 PE 7 10 TE 9 SPE GND 8 Description The Intersil HCTS160MS is a Radiation Hardened high speed presettable BCD decade synchronous counter that features an asynchronous reset and look-ahead carry logic. Counting and parallel presetting are accomplished synchronously with the lowto-high transition of the clock. A low level on the synchronous parallel enable input, SPE, disables counting and allows data at the preset inputs, P0 - P3, to be loaded into the counter. The counter is reset by a low on the master reset input, MR. Two count enables, PE and TE are provided for n-bit cascading. TE also controls the terminal count output, TC. The terminal count output indicates a maximum count for one clock pulse and is used to enable the next cascaded stage to count. MR 1 16 LEAD CERAMIC METAL SEAL FLATPACK PACKAGE (FLATPACK) MIL-STD-1835 CDFP4-F16 TOP VIEW MR 1 16 VCC CP 2 15 TC P0 3 14 Q0 P1 4 13 Q1 P2 5 12 Q2 P3 6 11 Q3 PE 7 10 TE GND 8 9 SPE The HCTS160MS utilizes advanced CMOS/SOS technology to achieve high-speed operation. This device is a member of radiation hardened, high-speed, CMOS/SOS Logic Family. The HCTS160MS is supplied in a 16 lead Ceramic flatpack (K suffix) or a SBDIP Package (D suffix). Ordering Information PART NUMBER TEMPERATURE RANGE SCREENING LEVEL PACKAGE HCTS160DMSR -55oC to +125oC Intersil Class S Equivalent 16 Lead SBDIP HCTS160KMSR -55oC to +125oC Intersil Class S Equivalent 16 Lead Ceramic Flatpack +25oC Sample 16 Lead SBDIP HCTS160K/Sample +25oC Sample 16 Lead Ceramic Flatpack HCTS160HMSR +25oC Die Die CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999 560 DB NA HCTS160D/Sample Spec Number File Number 518611 2484.2 HCTS160MS Functional Block Diagram P0 P1 3 P2 4 P3 5 6 SPE MR Q1 Q0 Q2 Q0 Q3 Q2 Q3 Q0 Q1 Q3 Q0 Q3 Q0 CP MR P MR D0 T0 P MR D1 Q0 T1 CP Q0 CP P MR D2 T2 Q1 Q3 Q3 P D3 T3 Q2 CP Q3 CP Q0 PE TE GND 8 VCC 16 14 Q0 15 13 TC 12 Q1 11 Q0 Q1 TRUTH TABLE INPUTS OPERATING MODE OUTPUTS MR CP PE TE SPE Pn Qn TC Reset (Clear) L X X X X X L L Parallel Load H X X l l L L H X X l h H (Note 1) Count H h h h (Note 3) X Count (Note 1) Inhibit H X l (Note 2) X h (Note 3) X qn (Note 1) H X X l (Note 2) h (Note 3) X qn L H = HIGH Voltage Level L = LOW Voltage Level h = HIGH voltage level one setup time prior to the LOW-to-HIGH clock transition l = LOW voltage level one setup time prior to the LOW-to-HIGH clock transition X = Immaterial q = Lower case letterindicate the state of the referenced output prior to the LOW-to-HIGH clock transition = LOW-to-HIGH clock transition NOTES: 1. The TC output is HIGH when TE is HIGH and the counter is at terminal count (HHHH for 161 and HLLH for 160) 2. The HIGH-to-LOW transition of PE or TE on the 54/74161 and 54/74160 should only occur while CP is high for conventional operation 3. The LOW-to-HIGH transition of SPE on the 54/74161 and 54/74160 should only occur while CP is high for conventional operation Spec Number 561 518611 Specifications HCTS160MS Absolute Maximum Ratings Reliability Information Supply Voltage (VCC). . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +7.0V Input Voltage Range, All Inputs . . . . . . . . . . . . .-0.5V to VCC +0.5V DC Input Current, Any One Input . . . . . . . . . . . . . . . . . . . . . . . .±10mA DC Drain Current, Any One Output. . . . . . . . . . . . . . . . . . . . . . .±25mA (All Voltage Reference to the VSS Terminal) Storage Temperature Range (TSTG) . . . . . . . . . . . -65oC to +150oC Lead Temperature (Soldering 10sec) . . . . . . . . . . . . . . . . . . +265oC Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1 Thermal Resistance θJA θJC SBDIP Package. . . . . . . . . . . . . . . . . . . . 73oC/W 24oC/W Ceramic Flatpack Package . . . . . . . . . . . 114oC/W 29oC/W Maximum Package Power Dissipation at +125oC Ambient SBDIP Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.68W Ceramic Flatpack Package . . . . . . . . . . . . . . . . . . . . . . . . . 0.44W If device power exceeds package dissipation capability, provide heat sinking or derate linearly at the following rate: SBDIP Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.7mW/oC Ceramic Flatpack Package . . . . . . . . . . . . . . . . . . . . . . 8.8mW/oC CAUTION: As with all semiconductors, stress listed under “Absolute Maximum Ratings” may be applied to devices (one at a time) without resulting in permanent damage. This is a stress rating only. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. The conditions listed under “Electrical Performance Characteristics” are the only conditions recommended for satisfactory device operation. Operating Conditions Supply Voltage (VCC). . . . . . . . . . . . . . . . . . . . . . . . +4.5V to +5.5V Input Rise and Fall Times at 4.5V VCC (TR, TF) . . . . . . .500ns Max Operating Temperature Range (TA) . . . . . . . . . . . . -55oC to +125oC Input Low Voltage (VIL). . . . . . . . . . . . . . . . . . . . . . . . . 0.0V to 0.8V Input High Voltage (VIH) . . . . . . . . . . . . . . . . . . . . . . .VCC/2 to VCC TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS PARAMETER Quiescent Current Output Current (Sink) Output Current (Source) Output Voltage Low Output Voltage High Input Leakage Current Noise Immunity Functional Test GROUP A SUBGROUPS TEMPERATURE MIN MAX UNITS 1 +25oC - 40 µA 2, 3 +125oC, -55oC - 750 µA 1 +25oC 4.8 - mA 2, 3 +125oC, -55oC 4.0 - mA 1 +25oC -4.8 - mA 2, 3 +125oC, -55oC -4.0 - mA VCC = 4.5V, VIH = 2.25V, IOL = 50µA, VIL = 0.8V 1, 2, 3 +25oC, +125oC, -55oC - 0.1 V VCC = 5.5V, VIH = 2.75V, IOL = 50µA, VIL = 0.8V 1, 2, 3 +25oC, +125oC, -55oC - 0.1 V VCC = 4.5V, VIH = 2.25V, IOH = -50µA, VIL = 0.8V 1, 2, 3 +25oC, +125oC, -55oC VCC -0.1 - V VCC = 5.5V, VIH = 2.75V, IOH = -50µA, VIL = 0.8V 1, 2, 3 +25oC, +125oC, -55oC VCC -0.1 - V VCC = 5.5V, VIN = VCC or GND 1 +25oC - ±0.5 µA 2, 3 +125oC, -55oC - ±5.0 µA 7, 8A, 8B +25oC, +125oC, -55oC - - - (NOTE 1) CONDITIONS SYMBOL ICC IOL IOH VOL VOH IIN FN VCC = 5.5V, VIN = VCC or GND VCC = 4.5V, VIH = 4.5V, VOUT = 0.4V, VIL = 0V VCC = 4.5V, VIH = 4.5V, VOUT = VCC - 0.4V, VIL = 0V VCC = 4.5V, VIH = 2.25V, VIL = 0.8V (Note 2) LIMITS NOTES: 1. All voltages referenced to device GND. 2. For functional tests, VO ≥ 4.0V is recognized as a logic “1”, and VO ≤ 0.5V is recognized as a logic “0”. Spec Number 562 518611 Specifications HCTS160MS TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS PARAMETER CP to QN SYMBOL TPHL TPLH CP to TC TPHL TPLH TE to TC TPHL TPLH MR to QN, TC (NOTES 1, 2) CONDITIONS TPHL GROUP A SUBGROUPS TEMPERATURE MIN MAX UNITS 9 +25oC 2 26 ns 10, 11 +125oC, -55oC 2 30 ns 9 +25oC 2 23 ns 10, 11 +125oC, -55oC 2 26 ns 9 +25oC 2 28 ns 10, 11 +125oC, -55oC 2 32 ns 9 +25oC 2 24 ns 10, 11 +125oC, -55oC 2 28 ns 9 +25oC 2 27 ns 10, 11 +125oC, -55oC 2 29 ns 9 +25oC 2 18 ns 10, 11 +125oC, -55oC 2 20 ns 9 +25oC 2 46 ns 10, 11 +125oC, -55oC 2 51 ns VCC = 4.5V VCC = 4.5V VCC = 4.5V VCC = 4.5V VCC = 4.5V VCC = 4.5V VCC = 4.5V LIMITS NOTES: 1. All voltages referenced to device GND. 2. AC measurements assume RL = 500Ω, CL = 50pF, Input TR = TF = 3ns, VIL = GND, VIH = 3V. TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS LIMITS PARAMETER SYMBOL Capacitance Power Dissipation CPD Input Capacitance Output Transition Time CIN TTHL TTLH CONDITIONS NOTES TEMPERATURE MIN MAX UNITS 1 +25oC - 104 pF 1 +125oC, -55oC - 260 pF 1 +25oC - 10 pF 1 +125oC - 10 pF 1 +25oC - 15 ns 1 +125oC - 22 ns VCC = 5.0V, f = 1MHz VCC = 5.0V,, f = 1MHz VCC = 4.5V NOTE: 1. The parameters listed in Table 3 are controlled via design or process parameters. Min and Max Limits are guaranteed but not directly tested. These parameters are characterized upon initial design release and upon design changes which affect these characteristics. Spec Number 563 518611 Specifications HCTS160MS TABLE 4. DC POST RADIATION ELECTRICAL PERFORMANCE CHARACTERISTICS 200K LIMITS PARAMETER (NOTES 1, 2) CONDITIONS SYMBOL TEMPERATURE MIN MAX UNITS Quiescent Current ICC VCC = 5.5V, VIN = VCC or GND +25oC - 0.75 mA Output Current (Sink) IOL VCC = 4.5V, VIN = VCC or GND, VOUT = 0.4V +25oC 4.0 - mA Output Current (Source) IOH VCC = 4.5V, VIN = VCC or GND, VOUT = VCC -0.4V +25oC -4.0 - mA Output Voltage Low VOL VCC = 4.5V and 5.5V, VIH = VCC/2, VIL = 0.8V, IOL = 50µA +25oC - -0.1 V Output Voltage High VOH VCC = 4.5V and 5.5V, VIH = VCC/2, VIL = 0.8V, IOH = -50µA +25oC VCC -0.1 - V Input Leakage Current IIN VCC = 5.5V, VIN = VCC or GND +25oC - ±5 µA Noise Immunity Functional Test FN VCC = 4.5V, VIH = 2.25V, VIL = 0.8V, (Note 3) +25oC - - - TPHL VCC = 4.5V +25oC 2 30 ns TPLH VCC = 4.5V +25oC 2 26 ns TPHL VCC = 4.5V +25oC 2 32 ns TPLH VCC = 4.5V +25oC 2 28 ns TPHL VCC = 4.5V +25oC 2 29 ns TPLH VCC = 4.5V +25oC 2 20 ns TPHL VCC = 4.5V +25oC 2 51 ns CP to QN CP to TC TE to TC MR to QN, TC NOTES: 1. All voltages referenced to device GND. 2. AC measurements assume RL = 500Ω, CL = 50pF, Input TR = TF = 3ns, VIL = GND, VIH = 3V. 3. For functional tests VO ≥ 4.0V is recognized as a logic “1”, and VO ≤ 0.5V is recognized as a logic “0”. TABLE 5. BURN-IN AND OPERATING LIFE TEST, DELTA PARAMETERS (+25oC) GROUP B SUBGROUP DELTA LIMIT ICC 5 12µA IOL/IOH 5 -15% of 0 Hour PARAMETER Spec Number 564 518611 Specifications HCTS160MS TABLE 6. APPLICABLE SUBGROUPS CONFORMANCE GROUPS METHOD GROUP A SUBGROUPS Initial Test (Preburn-In) 100%/5004 1, 7, 9 ICC, IOL/H Interim Test I (Postburn-In) 100%/5004 1, 7, 9 ICC, IOL/H Interim Test II (Postburn-In) 100%/5004 1, 7, 9 ICC, IOL/H PDA 100%/5004 1, 7, 9, Deltas Interim Test III (Postburn-In) 100%/5004 1, 7, 9 PDA 100%/5004 1, 7, 9, Deltas Final Test 100%/5004 2, 3, 8A, 8B, 10, 11 Sample/5005 1, 2, 3, 7, 8A, 8B, 9, 10, 11 Subgroup B-5 Sample/5005 1, 2, 3, 7, 8A, 8B, 9, 10, 11, Deltas Subgroup B-6 Sample/5005 1, 7, 9 Sample/6005 1, 7, 9 Group A (Note 1) Group B Group D READ AND RECORD Subgroups 1, 2, 3, 9, 10, 11 NOTE: 1. Alternate Group A testing in accordance with Method 5005 of Mil-Std-883 may be exercised. TABLE 7. TOTAL DOSE IRRADIATION TEST CONFORMANCE GROUPS Group E Subgroup 2 READ AND RECORD METHOD PRE RAD POST RAD PRE RAD POST RAD 5005 1, 7, 9 Table 4 1, 9 Table 4 (Note 1) NOTE: 1. Except FN test which will be performed 100% go/no-go. TABLE 8. STATIC AND DYNAMIC BURN-IN TEST CONNECTIONS OSCILLATOR OPEN GROUND 1/2 VCC = 3V ± 0.5V VCC = 6V ± 0.5V 50kHz 25kHz 1 - 10 - 16 - - 8 - 1 - 7, 9, 10, 16 - - 4, 6, 8 11 - 15 1, 3, 5, 7, 9, 10, 16 2 - STATIC I BURN-IN 11 - 15 STATIC II BURN-IN 11 - 15 DYNAMIC BURN-IN NOTES: 1. Each pin except VCC and GND will have a resistor of 10KΩ ± 5% for static burn-in 2. Each pin except VCC and GND will have a resistor of 1KΩ ± 5% for dynamic burn-in TABLE 9. IRRADIATION TEST CONNECTIONS OPEN GROUND VCC = 5V ± 0.5V 11 - 15 8 1 - 7, 9, 10, 16 NOTE: Each pin except VCC and GND will have a resistor of 47KΩ ± 5% for irradiation testing. Group E, Subgroup 2, sample size is 4 dice/wafer 0 failures. Spec Number 565 518611 HCTS160MS Intersil Space Level Product Flow - ‘MS’ Wafer Lot Acceptance (All Lots) Method 5007 (Includes SEM) 100% Interim Electrical Test 1 (T1) GAMMA Radiation Verification (Each Wafer) Method 1019, 4 Samples/Wafer, 0 Rejects 100% Static Burn-In 2, Condition A or B, 24 hrs. min., +125oC min., Method 1015 100% Nondestructive Bond Pull, Method 2023 100% Interim Electrical Test 2 (T2) Sample - Wire Bond Pull Monitor, Method 2011 100% Delta Calculation (T0-T2) Sample - Die Shear Monitor, Method 2019 or 2027 100% PDA 1, Method 5004 (Notes 1and 2) 100% Internal Visual Inspection, Method 2010, Condition A 100% Dynamic Burn-In, Condition D, 240 hrs., +125oC or Equivalent, Method 1015 100% Delta Calculation (T0-T1) 100% Temperature Cycle, Method 1010, Condition C, 10 Cycles 100% Interim Electrical Test 3 (T3) 100% Constant Acceleration, Method 2001, Condition per Method 5004 100% Delta Calculation (T0-T3) 100% PDA 2, Method 5004 (Note 2) 100% PIND, Method 2020, Condition A 100% Final Electrical Test 100% External Visual 100% Fine/Gross Leak, Method 1014 100% Serialization 100% Radiographic, Method 2012 (Note 3) 100% Initial Electrical Test (T0) 100% Static Burn-In 1, Condition A or B, 24 hrs. min., +125oC min., Method 1015 100% External Visual, Method 2009 Sample - Group A, Method 5005 (Note 4) 100% Data Package Generation (Note 5) NOTES: 1. Failures from Interim electrical test 1 and 2 are combined for determining PDA 1. 2. Failures from subgroup 1, 7, 9 and deltas are used for calculating PDA. The maximum allowable PDA = 5% with no more than 3% of the failures from subgroup 7. 3. Radiographic (X-Ray) inspection may be performed at any point after serialization as allowed by Method 5004. 4. Alternate Group A testing may be performed as allowed by MIL-STD-883, Method 5005. 5. Data Package Contents: • Cover Sheet (Intersil Name and/or Logo, P.O. Number, Customer Part Number, Lot Date Code, Intersil Part Number, Lot Number, Quantity). • Wafer Lot Acceptance Report (Method 5007). Includes reproductions of SEM photos with percent of step coverage. • GAMMA Radiation Report. Contains Cover page, disposition, Rad Dose, Lot Number, Test Package used, Specification Numbers, Test equipment, etc. Radiation Read and Record data on file at Intersil. • X-Ray report and film. Includes penetrometer measurements. • Screening, Electrical, and Group A attributes (Screening attributes begin after package seal). • Lot Serial Number Sheet (Good units serial number and lot number). • Variables Data (All Delta operations). Data is identified by serial number. Data header includes lot number and date of test. • The Certificate of Conformance is a part of the shipping invoice and is not part of the Data Book. The Certificate of Conformance is signed by an authorized Quality Representative. Spec Number 566 518611 HCTS160MS AC Timing Diagrams AC Load Circuit VIH DUT INPUT VS TEST POINT VIL CL TPLH RL TPHL VOH VS OUTPUT CL = 50pF VOL RL = 500Ω TTLH VOH TTHL 80% 20% VOL 80% OUTPUT 20% AC VOLTAGE LEVELS PARAMETER HCTS UNITS VCC 4.50 V VIH 3.00 V VS 1.30 V VIL 0 V GND 0 V All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com Sales Office Headquarters NORTH AMERICA Intersil Corporation P. O. Box 883, Mail Stop 53-204 Melbourne, FL 32902 TEL: (321) 724-7000 FAX: (321) 724-7240 EUROPE Intersil SA Mercure Center 100, Rue de la Fusee 1130 Brussels, Belgium TEL: (32) 2.724.2111 FAX: (32) 2.724.22.05 ASIA Intersil (Taiwan) Ltd. Taiwan Limited 7F-6, No. 101 Fu Hsing North Road Taipei, Taiwan Republic of China TEL: (886) 2 2716 9310 FAX: (886) 2 2715 3029 Spec Number 567 518611 HCTS160MS Die Characteristics DIE DIMENSIONS: 104 x 86 mils METALLIZATION: Type: AlSi Metal Thickness: 11kÅ ± 1kÅ GLASSIVATION: Type: SiO2 Thickness: 13kÅ ± 2.6kÅ WORST CASE CURRENT DENSITY: <2.0 x 105A/cm2 BOND PAD SIZE: 100µm x 100µm 4 mils x 4 mils Metallization Mask Layout HCTS160MS CD (2) MR (1) VCC (16) (15) TC P0 (3) (14) Q0 P1 (4) (13) Q1 P2 (5) (12) Q2 P3 (6) (11) Q3 PE (7) (8) GND (9) SPE (10) TE NOTE: The die diagram is a generic plot from a similar HCS device. It is intended to indicate approximate die size and bond pad location. The mask series for the HCTS160 is TA14445A. Spec Number 568 518611