AZ DISPLAYS, INC. COMPLETE LCD SOLUTIONS SPECIFICATIONS FOR OLED DISPLAY PART NUMBER: DATE: AZOLED034A & AZOLED034A-T August 27, 2009 AZOLED034A 1. General Description 1.1 Features AZOLED034A ACTIVE OLED PANEL Ultra Compact NTSC/PAL/SECAM Video Auto Switch Single Operation Voltage +12V CVBS / S-Video (Option) / Analog RGB (PC Mode) Signal Input Support Touch Screen Function (option) 1.2 Applications Portable product Industrial Hand-held Security Instrument Display Office Electronics 1.3 Application Precautions Do not use the products herein for the following equipment which demands extremely high performance in terms of functionality, reliability, or accuracy. Aerospace equipment Communication equipment for trunk lines. Control equipment for the nuclear power industry. Medical equipment related to life support, etc. The other application that demands high reliability and functionality should first contact a sales representative. AZ DISPLAYS, INC. PAGE 02 OF 23 2. Block Diagram 2.1 Block Diagram AZ DISPLAYS, INC. PAGE 3 OF 23 3.Panel Information 3.1 Panel Mechanical Specifications Parameter Specifications Unit Screen Size 3.4 (diagonal) inch Display Format 480 x (R.G.B) x 272 dot Active Area 74.88(W) x 42.43 (H) mm Pixel Pitch 0.156(W) x 0.156(H) mm Pixel Configuration Stripe Outline Area 82.8(W) x 54.3(H) mm Thickness 1.6 mm 3.2 Panel Optical Characteristics Parameter Symbol Horizontal Viewing Angle Vertical Condition Min Left Right CR >10 Top Bottom Typ Max Unit 170 --- deg 170 --- 170 --- deg 170 --- deg Re At optimized CR Contrast Ratio Viewing 5000:1 10000:1 --- --- --- --- --- 50 us --- angle Response time Rise Fall Uniformity Tr Tf --- θ= 0° U Brightness White Chromaticity LED Life Time AZ DISPLAYS, INC. --- --- 70 75 --- 170 200 230 x θ= 0° 0.23 0.28 0.33 y θ= 0° 25C 0.25 0.30 0.35 30000 --- --- Hr PAGE 04 OF 23 4.1 Panel Mechanical Specifications (With Touch) Parameter Specifications Unit Screen Size 3.4 (diagonal) inch Display Format 480 x (R.G.B) x 272 dot Active Area 74.88(W) x 42.43 (H) mm Pixel Pitch 0.156(W) x 0.156(H) mm Pixel Configuration Stripe Outline Area 82.8(W) x 54.3(H) mm Thickness 2.8 mm 4.2 Panel Optical Characteristics (With Touch) Parameter Symbol Horizontal Viewing Angle Vertical Condition Left Right Top Min Typ Max Unit --- 170 --- deg --- 170 --- ----- 170 170 --- deg --- deg CR >10 Bottom At optimized CR Contrast Ratio Viewing 5000:1 10000:1 --- --- --- --- --- 50 us cd/m² angle Response time Rise Fall Tr Tf θ= 0° Brightness White Chromaticity Operation life time AZ DISPLAYS, INC. ----- --- 136 160 184 x θ= 0° 0.26 0.31 0.36 y θ= 0° 25℃ 0.28 0.33 0.38 30000 --- --- Hr PAGE 5 OF 23 Remark 5. Dimension Information 5.1 Unit(AZOLED034A) AZ DISPLAYS, INC. PAGE 06 OF 23 AZ DISPLAYS, INC. 5.2 Unit (AZOLED034A-T) AZ DISPLAYS, INC. PAGE 7 OF 23 AZ DISPLAYS, INC. AZ DISPLAYS, INC. PAGE 8 OF 23 6. Pin Description 6.1 J301 OLED LCD Panel I/O Terminals(FPC 71 Pin Below Contact Type) Pin No Symbol I/O Description 1 TP1 I Touch panel P1 2 TP2 I Touch panel P2 3 TP3 I Touch panel P3. 4 TP4 I Touch panel P4 5 AR_VSS I Negative voltage for OLED 6 AR_VSS I Negative voltage for OLED 7 TEST1_VS open CMEL test pin, it must be open. 8 AR_VDD I Positive voltage for OLED 9 AR_VDD I Positive voltage for OLED 10 TEST2_VD open CMEL test pin, it must be open. 11 ARREF I/O 12 VGL I/O 13 VGH 14 LVO 15 C22N I/O Connect to the step-up circuit, capacitors according to the step-up factor. 16 C22P I/O Leave this pin open if the internal step-up circuit is not used. 17 HVO 18 C21P I/O Connect to the step-up circuit, capacitors according to the step-up factor. 19 C21N I/O Leave this pin open if the internal step-up circuit is not used. 20 C11N I/O 21 C11P I/O Connect to the step-up circuit, capacitors according to the step-up factor. 22 C12N I/O Leave this pin open if the internal step-up circuit is not used. 23 C12P I/O 24 PVSS 25 DDVDH 26 VSSA 27 VSSA 28 VCI 29 VCI 30 VGAM1OUT I/O I/O I/O I/O P I/O P P P Remark Panel refers voltage of the regulator ARREF or external input voltage.(-8V~+8V) Low Voltage output of regulator VGL or external input voltage.(-3V~-8V) High Voltage output of regulator VGH or external input voltage.(+3V~+8V) Negative output voltage of the booster2. (-8.5V) Positive output voltage of the booster2. (8.5V) Charge pump ground pin, it must connect to external ground. Output voltage of the booster1. (5.1V/6.0V) Analog ground pin. It must connect to external ground. Analog ground pin. It must connect to external ground. A power supply for the Analog circuit. (3.0V~3.6V) P A power supply for the Analog circuit. (3.0V~3.6V) Output voltage of the VGAM1OUT regulator and used positive powerof source driver. (4.8V/5.8V) Internal logic voltage input or output pin VDC_ENB=0, VDDD is output, please connect to 1uF capacitor. 31 I/O AZ DISPLAYS, INC. VDC0 VDDD Status 0 1.8 Norml display 1 2.5 OTP program PAGE 09 OF 23 VDC_ENB=1, VDDD is input. (Input range = 1.6V~2.75V) 32 VCC P A power supply for the Digital circuit. (1.5V~3.6V) 33 VSSD P Digital ground pin. It must connect to external ground. 34 NRESET I 35 NCS I Serial Interface chip enable pin. (Normally pull high) 36 SCL I Serial Interface clock input pin. (Normally pull high) 37 SDA I Serial Interface data line. (Normally pull high) Reset pin. Setting either pin low initializes the LSI. Must be reset after power is supplied. (Normally pull high) Data enable: 38 DE I When VSYNC+HSYNC+DE mode, DE=H: Data enable, DE=L: Data disable (Black). (Normally pull low) Frame synchronizing signal. 39 VSYNC I If VSPL=0: Active low. If VSPL=1: Active high. Line synchronizing signal. 40 HSYNC I If HSPL=0: Active low. If HSPL=1: Active high. Dot clock signal. If DPL=0: Data are input on the rising edge of DOTCLK. If 41 DCLK I 42 D27 I 43 D26 44 D25 45 D24 46 D23 only D07~D00 are used, and others short to GND. DX7~DX0 has 8-bit 47 D22 width, respectively to compose 16,777,216 color and 256 gray scale of 1 48 D21 pixel. 49 D20 50 D17 51 D16 52 D15 53 D14 54 D13 55 D12 56 D11 57 D10 58 D07 59 D06 60 D05 61 D04 62 D03 63 D02 DPL=1: Data are input on the falling edge of DOTCLK. Digital data input. DX0 is LSB and DX7 is MSB. (Normally pull low) 1. If parallel RGB input mode is used, D0X, D1X, and D2X indicate R, G, and B data in turn. 2. If serial RGB or RGBD or CCIR601 or CCIR656 input mode is selected, AZ DISPLAYS, INC. PAGE 10 OF 23 64 D01 65 D00 66 TEST3_W 67 AR_VDD I Positive voltage for OLED 68 AR_VDD I Positive voltage for OLED 69 AR_VSS I Negative voltage for OLED 70 AR_VSS I Negative voltage for OLED 71 TEST4_P open CMEL test pin, it must be open. open CMEL test pin, it must be open. 6.2 J101 Pin Assignment of Analog RGB Input (D-Sub 15 Pin) Pin No Symbol I/O Description 1 NC - No Connection 2 NC - No Connection 3 NC - No Connection 4 GND - Ground 5 NC 6 VS_IN I TTL Vertical sync 7 HS_IN I TTL Horizontal sync 8 AGND - Analog Ground 9 RI+ I Analog Red Signal 10 AGND - Analog Ground 11 GI+ I Analog Green Signal 12 AGND - Analog Ground 13 BI+ 14 GND Remark No Connection - Analog Blue Signal I - Ground AZ DISPLAYS, INC. PAGE 11 OF 23 6.3 J105 Pin Assignment of Key (Pitch 1.25mm 9Pin, Side Entry Type) Pin No Symbol I/O Description 1 N.C - No Connection 2 KEY-ADC1 I KEY ADC Input 1 3 KEY-ADC0 I KEY ADC Input 0 4 GND - Ground 5 VDD - +3.3V Output Voltage 6 IR_DATA I DATA of IR Receiver 7 LED-R O Index Red LED for power off control 8 LED-G O Index Green LED for power on control 9 GND - Ground Remark 6.4 J102C Pin Assignment of Signal Input (Pitch 1.25mm 15Pin, Side Entry Type) Pin No Symbol I/O Description Remark +12V Input Voltage 1 VCC12V 2 VCC12V - +12V Input Voltage 3 GND_D - Ground 4 GND_D - Ground 5 VIDEO1 I Video1 Input Signal 6 GND_A - Ground For Video1 7 VIDEO2 I Video2 Input Signal 8 GND_A - Ground For Video2 9 N.C 10 AGND - Analog Ground 11 S1_Y+ I Analog Luma Input of S-Video1 12 GND - Ground for Analog Luma Input of S-Video1 13 S1_C+ I Analog Chroma Input of S-Video1 14 GND - Ground for Analog Chroma Input of S-Video1 15 GND_D - Ground - No Connection - AZ DISPLAYS, INC. PAGE 12 OF 23 7. Absolute Maximum Ratings 7.1 Absolute Maximum Ratings Parameter Symbol Input Voltage Vin Video Input Signal Video in S-Video Input Signal Max Unit +14 V 0.5 2.0 Vp-p @75 S-Video in 0.5 2.0 Vp-p @75 Analog RGB Input Signal Analog RGB in 0.5 2.0 Vp-p @75 Digital Input Signal TTL +3.6 V Operating Temperature Storage Temperature AZ DISPLAYS, INC. Min +10 +0.3 -10 +60 -20 +70 Remark C C PAGE 13 OF 23 8. Recommended operating conditions 8.1 Electrical Characteristics Parameter Symbol Input Voltage Vin Total Current Iin I/O I Min Typ Max Unit +11 +12 +13 V I I Power Consumption Output Voltage VDD O Video Input Signal Video in I S-Video Input Signal S-Video in Y Analog RGB Input Signal Analog RGB in +3.2 195 mA 2.3 W +3.3 +3.4 Note @+12V V I=10mA 1.0 Vp-p @75 I 0.7 Vp-p @75 C I 0.286 Vp-p @75 RGB I 0.7 Vp-p @75 8.2 VGA Mode Characteristics Dots per inch Hor. Unit Polarity Ver. 640*480 31.469 KHz Negative 800*600 37.879 KHz Positive Unit Polarity Hz Negative Hz Positive 59.941 60.317 Note 8.3 Optics Sample Test Data Parameter S/N White Window Red Green Blue 0.281 0.651 0.282 0.148 .y 0.305 0.346 0.678 0.145 L(cd/m²) 349 TC(°K) 9150 001 x Remark ±15 BM-7 FAST(TOPCON) 2.Video Pattern Generator: FLUKE PM54200 3. Measurement Distance 500mm 50mm 4. TOPCON BM-7 Luminance Meter 2° filed of view is used in the testing (After 10min ~20min operation) AZ DISPLAYS, INC. PAGE 14 OF 23 9.Operation manual 9.1 Driver Board Manual To AZOLED034A KEYBOARD TO I/O BOARD To USB Board 9.2 Power and RCA Input Board (Optional) AZ DISPLAYS, INC. PAGE15 of 23 10. Key Function by OSD 10.1 Menu Operation Current selected indicator Meaning of the selected indicator Other indicators Current value Fig. 9-1 Expand current selected indicator Adjustable range To Driver Board (J105) POWER AUTO SOURCE MENU UP DOWN Operations of key board 1. To navigate the menu, press [MENU]. (Fig. 9-1) 2. The indicator lighting up in white color is the selected adjustment item. 3. To Next Item of the menu, press [MENU] again. 4. The operations below are only available when • MenuŽ is st arted. 5. Press [UP] / [DOWN] to adjust the value of the selected item. AZ DISPLAYS, INC. PAGE 16 OF 23 Overview of the menu Indicator Meaning Adjustable range For Remark Brightness 0 64 AV / S-Video / VGA Adjust-Bar Contrast 0 64 AV / S-Video / VGA Adjust-Bar Color 0 64 AV / S-Video Adjust-Bar Tint 0 32 AV / S-Video Sharpness 0 16 AV / S-Video Color Tone Normal / Warm / Cool Adjust-Bar AV / S-Video / VGA H-Position -25 +25 AV / S-Video / VGA Balance-Bar V-Position -10 +10 AV / S-Video / VGA Balance-Bar Auto Scan Information Setup VGA Over Scan / Under Scan AV / S-Video AV / S-Video / VGA Fig. 9-2 AV / S-V Fig. 9-3 Factory Set AV / S-Video / VGA Exit AV / S-Video / VGA Fig. 9-2 AZ DISPLAYS, INC. PAGE 17 OF 23 Setup Menu Firmware VER 0.25 above Fig. 9-3 Indicator Meaning Adjustable range Show Status ON / OFF Blue Screen ON / OFF Auto Power On ON / OFF Auto Sleep OFF / 3s / 5s / 15s / 30s Detect Source ON / OFF Function Remark ON: Show Show screen status. OFF: Hidden If loss signal will put on the ON: Blue blue or black screen. OFF: Black Power input module will be ON: Auto auto turn on. OFF: Manual If signal loss over setting ON: Auto times will be power off. OFF: Normal Auto detection which source ON: Auto in exist. OFF: Normal Return Note : Priority : Auto Sleep > Auto Power On Note : VGA Only don't have Detect Source function. AZ DISPLAYS, INC. PAGE 18 OF 23 10.2 Operation Indicator of input signal Video system Fig. 9-4 [Power] Monitor power on / off [Source] Input signal switch Overview of input signals Indicator Input signal Interface Video system VGA Analog RGB 640x480_60 / 800x600_60 AZ DISPLAYS, INC. PAGE 19 OF 23 11. Application Schematic Diagram 11.1 Application Circuit AZ DISPLAYS, INC. PAGE 20 OF 23 11.2 Key and IR Circuit AZ DISPLAYS, INC. PAGE 21 OF 23 11.3 Keyboard AZ DISPLAYS, INC. PAGE 22 OF 23 11.4 S-Video and RCA Input Board AZ DISPLAYS, INC. PAGE 23 OF 23