Document 428-1 Shielded Power Inductors – LPS3010 • Ultra small 3.0 × 3.0 mm footprint; less than 1.0 mm tall • Very low DCR; excellent current handling Core material Ferrite Core and winding loss See www.coilcraft.com/coreloss Environmental RoHS compliant, halogen free Terminations RoHS compliant matte tin over nickel over silver. Other terminations available at additional cost. Weight 25 – 32 mg Ambient temperature –40°C to +85°C with Irms current, +85°C to +125°C with derated current Storage temperature Component: –40°C to +125°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 1000/7″ reel; 3500/13″ reel; Plastic tape: 12 mm wide, 0.23 mm thick, 8 mm pocket spacing, 1.4 mm pocket depth Recommended pick and place nozzle OD: 3 mm; ID: ≤ 1.5 mm PCB washing Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. See Doc787_PCB_Washing.pdf. Isat (A)5 Irms (A)6 DCR SRF Inductance2 max3 typ4 10% 20% 30% 20°C 40°C Part number1 ±20% (µH) (Ohms) (MHz) drop drop drop rise rise LPS3010-471MR_ LPS3010-681MR_ LPS3010-102MR_ LPS3010-152MR_ LPS3010-182MR_ 0.47 0.68 1.0 1.5 1.8 0.070 0.080 0.085 0.120 0.150 370 270 230 165 150 1.8 1.6 1.5 1.3 1.2 1.9 1.7 1.6 1.4 1.2 2.0 1.7 1.6 1.4 1.3 1.3 1.3 1.1 1.05 1.00 1.80 1.75 1.50 1.40 1.40 LPS3010-222MR_ LPS3010-332MR_ LPS3010-472MR_ LPS3010-562MR_ LPS3010-682MR_ 2.2 3.3 4.7 5.6 6.8 0.220 0.220 0.300 0.400 0.450 130 110 92 80 70 1.3 0.83 0.72 0.67 0.61 1.4 0.88 0.75 0.69 0.63 1.4 0.90 0.77 0.71 0.64 0.90 0.85 0.70 0.60 0.56 1.10 1.10 0.95 0.78 0.74 LPS3010-822MR_ LPS3010-103MR_ LPS3010-123MR_ LPS3010-153MR_ LPS3010-183MR_ 8.2 10 12 15 18 0.520 0.540 0.700 0.950 1.10 62 58 47 43 40 0.56 0.50 0.46 0.41 0.38 0.59 0.53 0.49 0.43 0.40 0.59 0.55 0.50 0.44 0.41 0.53 0.48 0.44 0.37 0.33 0.70 0.64 0.58 0.48 0.47 LPS3010-223MR_ LPS3010-333MR_ LPS3010-473MR_ LPS3010-683MR_ LPS3010-104MR_ 22 33 47 68 100 1.20 2.00 3.20 3.50 5.25 36 27 21 21 14 0.32 0.25 0.23 0.20 0.14 0.35 0.27 0.24 0.21 0.16 0.36 0.28 0.25 0.22 0.17 0.30 0.26 0.22 0.20 0.18 0.41 0.35 0.31 0.28 0.24 LPS3010-124MR_ LPS3010-154MR_ LPS3010-184MR_ LPS3010-224MR_ 120 150 180 220 6.10 9.15 10.1 12.5 12 11 9 8 0.13 0.13 0.11 0.10 0.15 0.14 0.12 0.11 0.15 0.14 0.13 0.12 0.14 0.13 0.11 0.095 0.19 0.17 0.15 0.13 1. Please specify termination and packaging codes: LPS3010-223MRC Termination: R = RoHS compliant matte tin over nickel over silver. Special order, added cost: Q = RoHS tin-silver-copper (95.5/4/0.5) or P = non-RoHS tin-lead (63/37). Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic tape (1000 parts per full reel). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D = 13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (3500 parts per full reel). 2. Inductance tested at 100 kHz, 0.1 Vrms using an Agilent/HP 4192A. Inductance at 1 MHz is the same for parts with SRF ≥10 MHz. 3. DCR measured on a micro-ohmmeter. 4. SRF measured using an Agilent/HP 8753ES or equivalent. 5. DC current that causes the specified inductance drop from its value without current. 6. Current that causes the specified temperature rise from 25°C ambient. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Coilcraft Designer’s Kit C392 contains samples of 0.80 µH to 33 µH parts (3 each) from LPS3008, LPS3010 and LPS3015. Kit C401 contains samples of 0.56 µH to 33 µH parts (3 each) from LPS4012 and LPS4018. Kit C402 contains samples of 220 µH to 3300 µH parts (3 each) from all five series. For details of kit contents and to order, contact Coilcraft or visit http://order.coilcraft.com. Document 428-1 Revised 08/02/13 Document 428-2 Shielded SMT Power Inductors – LPS3010 Series L vs Frequency L vs Current 1000 1000 330 µH 100 68 µH Inductance (µH) Inductance (µH) 330 µH 33 µH 6.8 µH 10 3.3 µH 1 0.1 0.68 µH 0.01 0.1 1 10 Frequency (MHz) 100 68 µH 33 µH 6.8 µH 10 3.3 µH 1 0.1 0.68 µH 0.01 0.1 Current (A) 1 10 Typical Current Derating 120 100 90 80 70 60 50 40 30 20 25°C Percent of rated Current 110 Isat Irms 10 0 -40 -20 0 20 40 60 80 100 120 140 Ambient temperature (°C) Packaging 1000/7″ reel; 3500/13″ reel; Plastic tape: 12 mm wide, 0.23 mm thick, 8 mm pocket spacing, 1.4 mm pocket depth NOTE NEW PART ORIENTATION Parts are rotated 90° in the packaging tape compared to previous versions of this product. NEW Dimensions are in inches mm OLD 123 123 123 123 123 123 Document 428-2 Revised 08/02/13