EVB71101 315/433MHz Receiver Evaluation Board Description Features ! ! ! ! ! ! Single-conversion superhet architecture for low external component count FSK for digital data and FM reception for analog signal transmission FSK/FM demodulation with phase-coincidence demodulator Low current consumption in active mode and very low standby current Switchable LNA gain for improved dynamic range RSSI allows signal strength indication and ASK detection Ordering Information Part No. EVB71101-433-FSK-C EVB71101-433-ASK-C EVB71101-315-FSK-C EVB71101-315-ASK-C Application Examples Evaluation Board ! ! ! ! ! ! ! " ! General digital data transmission Tire Pressure Monitoring Systems (TPMS) Remote Keyless Entry (RKE) Wireless access control Alarm and security systems Garage door openers Remote Controls Home and building automation Low-power telemetry systems General Description The TH71101 FSK/FM/ASK single-conversion superheterodyne receiver IC is designed for applications in the European 433 MHz industrial-scientific-medical (ISM) band, according to the EN 300 220 telecommunications standard. It can also be used for any other system with carrier frequencies ranging from 300 MHz to 450 MHz (e.g. for applications to FCC part 15 and ARIB STD-T67). 39012 71101 01 Rev. 011 Page 1 of 14 EVB Description June/07 EVB71101 315/433MHz Receiver Evaluation Board Description Document Content 1 Theory of Operation ...................................................................................................3 1.1 General............................................................................................................................. 3 1.2 EVB Technical Data Overview ......................................................................................... 3 1.3 Block Diagram .................................................................................................................. 4 1.4 Mode Configurations ........................................................................................................ 4 1.5 LNA GAIN Control ............................................................................................................ 4 1.6 Frequency Planning.......................................................................................................... 4 1.6.1 1.6.2 2 Selected Frequency Plans........................................................................................................... 5 Maximum Frequency Coverage................................................................................................... 5 Application Circuits ...................................................................................................6 2.1 2.1.1 2.1.2 2.1.3 2.2 2.2.1 2.2.2 2.2.3 FSK Application Circuit..................................................................................................... 6 Circuit Diagram for FSK Reception.............................................................................................. 6 Board Component Values for FSK .............................................................................................. 7 Component Arrangement Top Side for FSK Reception .............................................................. 8 ASK Application Circuit..................................................................................................... 9 Circuit Diagram for ASK Reception ............................................................................................. 9 Board Component Values for ASK ............................................................................................ 10 Component Arrangement Top Side for ASK Reception ............................................................ 11 3 Evaluation Board Layouts .......................................................................................12 4 Board Variants..........................................................................................................12 5 Package Description ................................................................................................13 5.1 6 Soldering Information ..................................................................................................... 13 Disclaimer .................................................................................................................14 39012 71101 01 Rev. 011 Page 2 of 14 EVB Description June/07 EVB71101 315/433MHz Receiver Evaluation Board Description 1 Theory of Operation 1.1 General With the TH71101 receiver chip, various circuit configurations can be arranged in order to meet a number of different customer requirements. For FM/FSK reception the IF tank used in the phase coincidence demodulator can also be constituted by a ceramic discriminator with a varactor diode to create an AFC circuit. In ASK configuration, the RSSI signal is fed to an ASK detector, which is constituted by the operational amplifier. A double-conversion variant, called TH71102, is also available. This receiver IC allows a higher degree of image rejection, achieved in conjunction with an RF front-end filter. Both RXICs have the same die. At the TH71102, the second mixer (MIX2) is used to down-convert the first IF (IF1) to the second IF (IF2). At the TH71101, MIX2 operates as an amplifier. Efficient RF front-end filtering is realized by using a SAW, ceramic or helix filter in front of the LNA and by adding an LC filter at the LNA output. The TH71101 receiver IC consists of the following building blocks: # # # # # # # # 1.2 PLL synthesizer (PLL SYNTH) for generation of the local oscillator signal LO parts of the PLL SYNTH are: the high-frequency VCO1, the feedback divider DIV_16, a phase-frequency detector (PFD) with charge pump (CP) and a crystal-based reference oscillator (RO) Low-noise amplifier (LNA) for high-sensitivity RF signal reception First mixer (MIX1) for down-conversion of the RF signal to the IF IF pre amplifier which is a mixer cell (MIX2) that operates as an amplifier IF amplifier (IFA) to amplify and limit the IF signal and for RSSI generation Phase coincidence demodulator (DEMOD) with third mixer (MIX3) to demodulate the IF signal Operational amplifier (OA) for data slicing, filtering and ASK detection Bias circuitry for bandgap biasing and circuit shutdown EVB Technical Data Overview ! Input frequency range: 300 MHz to 450 MHz ! Power supply range: 2.3 V to 5.5 V @ ASK 2.7 V to 5.5 V @ FSK ! Temperature range: -40 °C to +85 °C ! Standby current: 50 nA ! Operating current: 6.5 mA @ low gain mode 8.2 mA @ high gain mode ! Sensitivity: -110 dBm @ ASK 1) -104 dBm @ FSK 2) ! Range of IF: 400 kHz to 22 MHz ! Maximum input level: -10 dBm @ ASK 0 dBm @ FSK ! Image rejection: > 45 dB (e.g. with 433.92 MHz SAW front-end filter and at 10.7 MHz IF) ! Spurious emission: < -70 dBm ! Input frequency acceptance range: up to ±100 kHz ! RSSI range: 70 dB ! FM/FSK deviation range: ±2.5 kHz to ±80 kHz ! Maximum analog modulation frequency: 15 kHz 1) at 4 kbps NRZ, BER = 3⋅10-3, 180 kHz IF filter BW, incl. 3 dB SAW front-end-filter loss 2) at 4 kbps NRZ, BER = 3⋅10-3, ± 20 kHz FSK deviation, 180 kHz IF filter BW, incl. 3 dB SAW front-endfilter loss For more detailed information, please refer to the latest TH71101 data sheet revision 39012 71101 01 Rev. 011 Page 3 of 14 EVB Description June/07 EVB71101 315/433MHz Receiver Evaluation Board Description IN_LNA 31 21 14 15 16 MIX1 IF LNA MIX2 IN_DEM 13 OUT_IFA 12 RSSI 11 FBC1 10 IN_IFA 9 VEE_IF 8 OUT_MIX2 7 VCC_MIX 6 IF1N 5 IF1P 4 VEE_MIX 3 IN_MIX1 2 OUT_LNA 1 GAIN_LNA Block Diagram VEE_LNAC 1.3 OUTP MIX3 IF 23 IFA OUTN 24 LO OAP OA 20 OAN 19 PFD OUT_OA RO 27 28 22 17 VCC_BIAS 25 ENRX 26 RO VCC_PLL 29 LF VEE_RO 30 18 BIAS CP VEE_LNA 32 VCC_LNA VCO1 VEE_BIAS DIV_16 Fig. 1: TH71101 block diagram 1.4 Mode Configurations ENRX Mode Description 0 RX standby RX disabled 1 RX active RX enable Note: ENRX are pulled down internally 1.5 LNA GAIN Control VGAIN_LNA Mode Description < 0.8 V HIGH GAIN LNA set to high gain > 1.4 V LOW GAIN LNA set to low gain Note: hysteresis between gain modes to ensure stability 1.6 Frequency Planning Frequency planning is straightforward for single-conversion applications because there is only one IF that can be chosen, and then the only possible choice is low-side or high-side injection of the LO signal (which is now the one and only LO signal in the receiver). The receiver’s single-conversion architecture requires careful frequency planning. Besides the desired RF input signal, there are a number of spurious signals that may cause an undesired response at the output. Among them is the image of the RF signal that must be suppressed by the RF front-end filter. 39012 71101 01 Rev. 011 Page 4 of 14 EVB Description June/07 EVB71101 315/433MHz Receiver Evaluation Board Description By using the internal PLL synthesizer of the TH71101 with the fixed feedback divider ratio of N = 16 (DIV_16), two types of down-conversion are possible: low-side injection of LO and high-side injection of LO. The following table summarizes some equations that are useful to calculate the crystal reference frequency (REF) and the LO frequency, for a given RF and IF. 1.6.1 Injection type low high REF (RF – IF)/16 (RF + IF)/16 LO 16 • REF 16 • REF IF RF – LO LO – RF RF image RF – 2IF RF + 2IF Selected Frequency Plans The following table depicts crystal, LO and image signals considering the examples of 315 MHz and 433.92 MHz RF reception at IF = 10.7 MHz. Signal type RF = 315 MHz RF = 315 MHz RF = 433.92 MHz RF = 433.92 MHz Injection type low high low high REF / MHz 19.01875 20.35625 26.45125 27.78875 LO / MHz 304.3 325.7 423.22 444.62 RF image / MHz 293.6 336.4 412.52 455.32 The selection of the reference crystal frequency is based on some assumptions. As for example: the image frequency should not be in a radio band where strong interfering signals might occur (because they could represent parasitic receiving signals), the LO signal should be in the range of 300 MHz to 450 MHz (because this is the optimum frequency range of the VCO1). Furthermore the IF should be as high as possible to achieve highest RF image rejection. The columns in bold depict the selected frequency plans to receive at 315 MHz and 433.92 MHz, respectively. 1.6.2 Maximum Frequency Coverage Parameter fmin fmax Injection type high low RF / MHz 289.3 460.7 REF / MHz 18.75 28.125 LO / MHz 300 450 IF/ MHz 10.7 10.7 39012 71101 01 Rev. 011 Page 5 of 14 EVB Description June/07 EVB71101 315/433MHz Receiver Evaluation Board Description 2 Application Circuits 2.1 FSK Application Circuit RSSI GND OUT_OA GND Circuit Diagram for FSK Reception OUTP GND 2.1.1 1 2 1 2 1 2 FSK output C16 C15 C17 R4 R5 XTAL CB3 VCC VCC 17 OAN 19 OAP 20 VEE 22 TH71101 29 LF GAIN_LNA OUT_LNA IN_MIX1 VEE IF1P IF1N VCC CB1 R2 C10 VEE 10 1 2 3 4 5 6 7 8 32 VCC C11 FBC1 12 IN_IFA 11 31 IN_LNA CB4 C9 VEE L2 VCC FBC2 13 30 VEE 50 L1 6 1 SAWFIL 3 4 C3 C12 VCC 14 28 ENRX R1 IN_LNA 16 27 VCC CB2 CERDIS OUT_IFA 15 26 RO 1 2 3 VCC ENRX GND 25 VEE C_RO OUT_OA 18 VCC RSSI 21 24 1 2 GND RO OUTP 23 C1 OUT_MIX2 9 CERFIL C7 RL2 RL1 CB5 VCC C6 CB8 2 1 CB6 L3 GND VCC CB7 Circuit Features • • Tolerates input frequency variations Well-suited for NRZ, Manchester and similar codes 39012 71101 01 Rev. 011 Page 6 of 14 EVB Description June/07 EVB71101 315/433MHz Receiver Evaluation Board Description 2.1.2 Board Component Values for FSK Part Size Value @ 315 MHz Value @ 433.92 MHz C1 0805 27 pF 27 pF ±5% crystal series capacitor C3 0603 1 nF 1 nF ±10% loop filter capacitor C6 0603 6.8 pF 4.7 pF ±5% LNA output tank capacitor C7 0603 2.7 pF 2.2 pF ±5% MIX1 input matching capacitor C9 0603 33 nF 33 nF ±10% IFA feedback capacitor C10 0603 1 nF 1 nF ±10% IFA feedback capacitor C11 0603 1 nF 1 nF ±10% IFA feedback capacitor C12 0805 10 pF 10 pF ±5% DEMOD phase-shift capacitor C15 0805 100 pF 100 pF ±5% demodulator output low-pass capacitor, this value for data rates < 20 kbps NRZ, for higher data rates decrease the value C16 0805 1.5 nF 1.5 nF ±10% RSSI output low-pass capacitor C17 0805 10 nF 10 nF ±10% data slicer capacitor, this value for data rates > 0.8 kbps NRZ, for lower data rates increase the value CB1 to CB5 CB7 to CB8 0603 330 pF 330 pF ±10% de-coupling capacitor CB6 0805 33 nF 33 nF ±10% de-coupling capacitor Tolerance Description C_RO 0603 330 pF 330 pF ±5% optional capacitor, to couple external RO signal R1 0805 10 kΩ 10 kΩ ±5% loop filter resistor R2 0603 330 Ω 330 Ω ±5% optional CERFIL output matching resistor R4 0805 330 kΩ 330 kΩ ±5% data slicer resistor R5 0805 220 kΩ 220 kΩ ±5% loading resistor RL1 0805 470 Ω 470 Ω ±5% MIX1 bias resistor RL2 0805 470 Ω 470 Ω ±5% MIX1 bias resistor L1 0603 0Ω 68 nH ±5% L2 0603 33 nH 82 nH ±5% SAW filter matching inductor from Würth-Elektronik (WE-KI series), or equivalent part L3 0603 22 nH 15 nH ±5% 20.35625 MHz @ RF = 315 MHz 26.45125 MHz @ RF = 433.92 MHz ±25ppm cal. ±30ppm temp. SAFCC433MBL0X00 (f0 = 433.92 MHz) B3dB = 840 kHz XTAL SMD 6x3.5 HC49 SMD SAWFIL SMD 3x3 SAFDC315MSM0T00 (f0 = 315.00 MHz) CERFIL SMD 3.45x3.1 SFECF10M7HA00 CERDIS SMD 4.5x2 CDSCB10M7GA135 39012 71101 01 Rev. 011 LNA output tank inductor from Würth-Elektronik (WE-KI series), or equivalent part fundamental-mode crystal from Telcona/Horizon (HEX22 series) or equivalent part fundamental-mode crystal, Cload = 10 pF to 15 pF, C0, max = 7 pF, R1, max = 50 Ωl low-loss SAW filter from Murata, or equivalent part B3dB = 5MHz B3dB = 180 kHz ceramic filter from Murata, or equivalent part ceramic discriminator from Murata, or equivalent part Page 7 of 14 EVB Description June/07 EVB71101 315/433MHz Receiver Evaluation Board Description 2.1.3 Component Arrangement Top Side for FSK Reception 1 OUT_OA RSSI OUTP Melexis OUTN Board size is 42.7mm x 37.5mm 1 C16 C15 1 R5 1 0Ω 17 16 L2 32 1 C12 C11 R2 C9 CB2 TH71101 L1 0Ω CB4 24 25 C3 R1 RF_input CB3 C1 C-RO CERDIS C17 1 ENRX RO R4 XTAL C10 8 9 CB1 39012 71101 01 Rev. 011 Page 8 of 14 VCC 1 CB6 RL2 CB8 EVB711XX_4 RL1 L3 C6 IN_LNA CB7 CB5 C7 EVB Description June/07 EVB71101 315/433MHz Receiver Evaluation Board Description Circuit Diagram for ASK Reception OUT_OA GND 2.2.1 ASK Application Circuit RSSI GND 2.2 1 2 1 2 ASK output C16 R4 C17 CB3 VCC XTAL CB2 28 ENRX C3 VCC 17 OAN 19 OAP 20 VEE 22 TH71101 29 LF OUT_LNA IN_MIX1 VEE IF1P IF1N VCC CB1 R2 C10 VEE 10 GAIN_LNA 31 IN_LNA C11 FBC1 12 IN_IFA 11 1 2 3 4 5 6 7 8 32 VCC CB4 C9 VEE L2 VCC FBC2 13 30 VEE 50 L1 6 1 SAWFIL 3 4 VCC 14 27 VCC R1 IN_LNA 16 OUT_IFA 15 26 RO 1 2 3 VCC ENRX GND 25 VEE C_RO OUT_OA 18 VCC RSSI 21 24 1 2 GND RO OUTP 23 C1 OUT_MIX2 9 CERFIL C7 RL2 RL1 CB5 VCC 39012 71101 01 Rev. 011 CB8 Page 9 of 14 C6 2 1 CB6 L3 GND VCC CB7 EVB Description June/07 EVB71101 315/433MHz Receiver Evaluation Board Description 2.2.2 Board Component Values for ASK Part Size Value @ 315 MHz Value @ 433.92 MHz C1 0805 27 pF 27 pF ±5% crystal series capacitor C3 0603 1 nF 1 nF ±10% loop filter capacitor C6 0603 6.8 pF 4.7 pF ±5% LNA output tank capacitor C7 0603 2.7 pF 2.2 pF ±5% MIX1 input matching capacitor C9 0603 33 nF 33 nF ±10% IFA feedback capacitor C10 0603 1 nF 1 nF ±10% IFA feedback capacitor C11 0603 1 nF 1 nF ±10% IFA feedback capacitor C16 0805 1.5 nF 1.5 nF ±10% RSSI output low-pass capacitor, this value for data rates < 10 kbps NRZ, for higher data rates decrease the value C17 0805 10 nF 10 nF ±10% data slicer capacitor, this value for data rates > 0.8 kbps NRZ, for lower data rates increase the value CB1 to CB5 CB7 to CB8 0603 330 pF 330 pF ±10% de-coupling capacitor CB6 0805 33 nF 33 nF ±10% de-coupling capacitor C_RO 0603 330 pF 330 pF ±5% optional capacitor, to couple external RO signal Tolerance Description R1 0805 10 kΩ 10 kΩ ±5% loop filter resistor R2 0603 330 Ω 330 Ω ±5% optional CERFIL output matching resistor R4 0805 330 kΩ 330 kΩ ±5% data slicer resistor RL1 0805 470 Ω 470 Ω ±5% MIX1 bias resistor RL2 0805 470 Ω 470 Ω ±5% MIX1 bias resistor L1 0603 0Ω 68 nH ±5% L2 0603 33 nH 82 nH ±5% SAW filter matching inductor from Würth-Elektronik (WE-KI series), or equivalent part L3 0603 22 nH 15 nH ±5% SMD 6x3.5 XTAL HC49 SMD SAWFIL CERFIL SMD 3x3 SMD 3.45x3.1 39012 71101 01 Rev. 011 20.35625 MHz @ RF = 315 MHz 26.45125 MHz @ RF = 433.92 MHz ±25ppm cal. ±30ppm temp. SAFCC433MBL0X00 (f0 = 433.92 MHz) B3dB = 840 kHz SAFDC315MSM0T00 (f0 = 315.00 MHz) SFECF10M7HA00 LNA output tank inductor from Würth-Elektronik (WE-KI series), or equivalent part fundamental-mode crystal from Telcona/Horizon (HEX22 series) or equivalent part fundamental-mode crystal, Cload = 10 pF to 15 pF, C0, max = 7 pF, R1, max = 50 Ωl low-loss SAW filters from Murata or equivalent part B3dB = 5MHz B3dB = 180 kHz Page 10 of 14 ceramic filter from Murata, or equivalent part EVB Description June/07 EVB71101 315/433MHz Receiver Evaluation Board Description 2.2.3 Component Arrangement Top Side for ASK Reception OUT_OA RSSI OUTP 1 C16 1 1 XTAL C17 17 16 TH71101 L1 L2 32 1 R2 C9 CB2 C11 CB4 24 25 C3 R1 RF_input CB3 C1 C-RO 0Ω 1 ENRX RO R4 Melexis OUTN Board size is 42.7mm x 37.5mm C10 8 9 CB1 39012 71101 01 Rev. 011 Page 11 of 14 VCC 1 CB6 RL2 CB8 EVB711XX_4 RL1 L3 C6 IN_LNA CB7 CB5 C7 EVB Description June/07 EVB71101 315/433MHz Receiver Evaluation Board Description 3 Evaluation Board Layouts VCC Board layout data in Gerber format is available, board size is 37.5mm x 42.7mm. OUT_OA RSSI OUTP EVB711XX_4 IN_LNA ENRX RO Melexis OUTN 4 Melexis PCB bottom view PCB top view Board Variants Type EVB71101 Frequency/MHz Modulation Board Execution –315 –FSK –A antenna version –433 –ASK –C connector version –868 –FM –915 Note: 39012 71101 01 Rev. 011 available EVB setups Page 12 of 14 EVB Description June/07 EVB71101 315/433MHz Receiver Evaluation Board Description 5 Package Description The device TH71101 is RoHS compliant. D D1 A 24 17 16 25 b E e E1 32 9 1 8 A2 A1 12° +1° 0.25 (0.0098) c 12° +1° L .10 (.004) Fig. 2: LQFP32 (Low profile Quad Flat Package) All Dimension in mm, coplanaríty < 0.1mm E1, D1 E, D A A1 A2 e b c L α 7.00 9.00 1.40 1.60 0.05 0.15 1.35 1.45 0.8 0.30 0.45 0.09 0.20 0.45 0.75 0° 7° 0.053 0.057 0.031 0.012 0.018 0.0035 0.0079 0.018 0.030 0° 7° min max All Dimension in inch, coplanaríty < 0.004” min max 5.1 0.276 0.354 0.055 0.063 0.002 0.006 Soldering Information • 39012 71101 01 Rev. 011 The device TH71101 is qualified for MSL3 with soldering peak temperature 260 deg C according to JEDEC J-STD-2. Page 13 of 14 EVB Description June/07 EVB71101 315/433MHz Receiver Evaluation Board Description 6 Disclaimer 1) The information included in this documentation is subject to Melexis intellectual and other property rights. Reproduction of information is permissible only if the information will not be altered and is accompanied by all associated conditions, limitations and notices. 2) Any use of the documentation without the prior written consent of Melexis other than the one set forth in clause 1 is an unfair and deceptive business practice. Melexis is not responsible or liable for such altered documentation. 3) The information furnished by Melexis in this documentation is provided ’as is’. Except as expressly warranted in any other applicable license agreement, Melexis disclaims all warranties either express, implied, statutory or otherwise including but not limited to the merchantability, fitness for a particular purpose, title and non-infringement with regard to the content of this documentation. 4) Notwithstanding the fact that Melexis endeavors to take care of the concept and content of this documentation, it may include technical or factual inaccuracies or typographical errors. Melexis disclaims any responsibility in connection herewith. 5) Melexis reserves the right to change the documentation, the specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with Melexis for current information. 6) Melexis shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interrupt of business or indirect, special incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the information in this documentation. 7) The product described in this documentation is intended for use in normal commercial applications. Applications requiring operation beyond ranges specified in this documentation, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are specifically not recommended without additional processing by Melexis for each application. 8) Any supply of products by Melexis will be governed by the Melexis Terms of Sale, published on www.melexis.com. © Melexis NV. All rights reserved. For the latest version of this document, go to our website at: www.melexis.com Or for additional information contact Melexis Direct: Europe, Africa: Americas: Asia: Phone: +32 1367 0495 E-mail: [email protected] Phone: +1 603 223 2362 E-mail: [email protected] Phone: +32 1367 0495 E-mail: [email protected] ISO/TS 16949 and ISO14001 Certified 39012 71101 01 Rev. 011 Page 14 of 14 EVB Description June/07