LT3692A Monolithic Dual Tracking 3.5A Step-Down Switching Regulator Description Features n n n n n n n n n n n Wide Input Range: – Operation from 3V to 36V – OVLO Protects Circuit Through 60V Transients Independent Supply, Shutdown, Soft-Start, UVLO, Programmable Current Limit and Programmable Power Good for Each 3.5A Regulator Die Temperature Monitor Adjustable/Synchronizable Fixed Frequency Operation from 250kHz to 2MHz with Synchronized Clock Output Independent Synchronized Switching Frequencies Optimize Component Size Antiphase Switching Outputs Can Be Paralleled Flexible Output Voltage Tracking Low Dropout: 95% Maximum Duty Cycle 5mm × 5mm QFN Package FMEA Compliant 38-Pin Exposed Pad TSSOP Package Applications n n Automotive Supplies Distributed Supply Regulation L, LT, LTC, LTM, Linear Technology, the Linear logo and Burst Mode are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. The LT®3692A is a dual current mode PWM step-down DC/DC converter with two internal 3.8A switches. Independent input voltage, shutdown, feedback, soft-start, UVLO current limit and comparator pins for each channel simplify complex power supply tracking and sequencing requirements. To optimize efficiency and component size, both converters have a programmable maximum current limit and are synchronized to either a common external clock input, or a resistor settable fixed 250kHz to 2MHz internal oscillator. A frequency divider is provided for channel 1 to further optimize component size. At all frequencies, a 180° phase relationship between channels is maintained, reducing voltage ripple and component size. A clock output is available for synchronizing multiple regulators. Minimum input to output voltage ratios are improved by allowing the switch to stay on through multiple clock cycles only switching off when the boost capacitor needs recharging. Independent channel operation can be programmed using the SHDN pin. Disabling both converters reduces the total quiescent current to <10µA. The LT3692A is an improved version of the LT3692 with reduced minimum on-time. Typical Application Independent Synchronized Switching Frequencies Extend Full Frequency Input Range 3.3V and 1.2V 2-Stage Dual Step-Down Multi-Frequency Converter VOUT1 VIN1 5.5V TO 36V 4.7µF SHDN1 BST1 VOUT1 3.3V 2.5A 550kHz 0.22µF 100k 47µF 4.7µH 24.9k SHDN2 BST2 SW1 SW2 IND1 IND2 LT3692A VOUT2 VOUT1 FB1 8.06k PG CMPI1 CMPI2 CMPO1 CMPO2 100k 13k SS2 ILIM2 VC2 RT/SYNC 33pF 680pF DIV 68.1k 102k 0.1µF 0.5µH 4.02k FB2 SS1 ILIM1 VC1 0.1µF CH1: 550kHz VIN2 VIN1 CLKOUT GND TJ FB1 100p 47µF VOUT2 1.2V 1A 2.2MHz CH2: 2.2MHz VIN = 30V 3692A TA01b 8.06k CLKOUT 2.2MHz 0.1µF 220pF 22pF 10nF 40.2k 33.2k 3692a TA01a 3692a TA01c 3692afc For more information www.linear.com/3692A 1 LT3692A Absolute Maximum Ratings (Note 1) VIN1/2, SHDN1/2, CMPO1/2........................................40V VIN1/2 Transient (Note 2)............................................60V SW1/2.....................................................................VIN1/2 BST1/2.......................................................................60V BST1/2 Pin Above SW1/2...........................................25V IND1/2, VOUT1/2..........................................................40V FB1/2, CMPI1/2, SS1/2.................................................5V RT/SYNC......................................................................5V DIV, ILIM1/2..............................................................3.0V VC1/2, TJ............................................................... ±100µA Operating Junction Temperature Range (Note 3) LT3692AEUH...................................... –40°C to 125°C LT3692AIUH....................................... –40°C to 125°C LT3692AHUH...................................... –40°C to 150°C LT3692AEFE....................................... –40°C to 125°C LT3692AIFE........................................ –40°C to 125°C LT3692AHFE....................................... –40°C to 150°C Storage Temperature Range................... –65°C to 150°C Pin Configuration SS1 VIN1 SW1 DNC* IND1 DNC* VOUT1 TOP VIEW SHDN1 TOP VIEW 32 31 30 29 28 27 26 25 BST1 1 23 VC1 FB1 4 IND1 2 37 NC NC 3 36 VIN1 VOUT1 4 35 SHDN1 NC 5 34 SS1 6 33 ILIM1 7 32 VC1 CMPI1 8 31 NC FB1 9 30 RT/SYNC 21 CLKOUT 33 GND 38 SW1 BST1 22 RT/SYNC CMPI1 3 1 CMPO1 24 ILIM1 CMPO1 2 NC 20 TJ NC 10 CMPI2 6 19 DIV FB2 11 CMPO2 7 18 VC2 CMPI2 12 27 DIV CMPO2 13 26 VC2 FB2 5 17 ILIM2 BST2 8 BST2 14 SS2 SHDN2 VIN2 SW2 IND2 DNC* DNC* VOUT2 9 10 11 12 13 14 15 16 NC 15 VOUT2 16 UH PACKAGE 32-LEAD (5mm × 5mm) PLASTIC QFN NC 17 IND2 18 θJA = 23°C/W, θJC(PAD) = 1.5°C/W EXPOSED PAD (PIN 33) IS GND, MUST BE SOLDERED TO PCB *DO NOT CONNECT NC 19 39 GND 29 CLKOUT 28 TJ 25 ILIM2 24 SS2 23 SHDN2 22 VIN2 21 NC 20 SW2 FE PACKAGE 38-LEAD PLASTIC TSSOP θJA = 17.5°C/W, θJC(PAD) = 3°C/W EXPOSED PAD (PIN 39) IS GND, MUST BE SOLDERED TO PCB 2 3692afc For more information www.linear.com/3692A LT3692A Order Information LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT3692AEUH#PBF LT3692AEUH#TRPBF 3692A 32-Lead (5mm × 5mm) Plastic QFN –40°C to 125°C LT3692AIUH#PBF LT3692AIUH#TRPBF 3692A 32-Lead (5mm × 5mm) Plastic QFN –40°C to 125°C LT3692AHUH#PBF LT3692AHUH#TRPBF 3692A 32-Lead (5mm × 5mm) Plastic QFN –40°C to 150°C LT3692AEFE#PBF LT3692AEFE#TRPBF 3692AFE 38-Lead Plastic TSSOP –40°C to 125°C LT3692AIFE#PBF LT3692AIFE#TRPBF 3692AFE 38-Lead Plastic TSSOP –40°C to 125°C LT3692AHFE#PBF LT3692AHFE#TRPBF 3692AFE 38-Lead Plastic TSSOP –40°C to 150°C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VVIN1/2 = 15V unless otherwise specified. (Note 3) PARAMETER CONDITIONS MIN TYP MAX 1.24 1.32 1.4 V –1 0 1 µA VIN1 Undervoltage Lockout (Note 4) 2.5 2.8 3.1 V VIN Overvoltage Lockout Ch 1/2 (Note 5) 36 39 43 V 6 13 µA SHDN Voltage Threshold Ch 1/2 SHDN Input Current Ch 1/2 l VSHDN = 1.35V VIN1 Shutdown Current VSHDN = 0V l VIN2 Shutdown Current VSHDN = 0V l VIN1 Quiescent Current VSHDN = 2V VIN2 Quiescent Current VSHDN = 2V UNITS 0 2 µA 3 4 5 mA 400 630 1000 µA Feedback Voltage Ch 1/2 VVC1/2 = 1V l 790 806 822 mV Feedback Voltage Regulation VVIN1/2 = 3V to 35V, VVC1/2 = 0.5V to 1.4V l 780 806 830 mV Feedback Voltage Offset Ch 1 to Ch 2 VVC1/2 = 1V l –13 0 13 mV Feedback Bias Current Ch 1/2 VVC1/2 = 1V l 0 85 200 nA TJ Output Voltage (Note 6) TJ = 25°C, ITJ = 25µA, Temperature = 25°C ITJ = 25µA, Temperature = 125°C ITJ = 25µA, Temperature = –40°C TJ Error Temperature = 25°C to 125°C Error Amp gm Ch 1/2 VVC1/2 = 1V, IVC1/2 = ±10µA 250 1.23 –380 l mV V mV –100 0 100 mV 300 400 500 µMho Error Amp Source Current Ch 1/2 VFB1/2 = 0.7V, VVC1/2 = 1V 17 25 33 µA Error Amp Sink Current Ch 1/2 VFB1/2 =0.9V, VVC1/2 = 1V 20 28 36 µA Error Amp High Clamp Ch 1/2 VFB1/2 = 0.7V 1.7 1.9 2.1 V Error Amp Switching Threshold Ch 1/2 VFB1/2 = 0V 0.7 0.9 1.08 V 3692afc For more information www.linear.com/3692A 3 LT3692A Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VVIN1/2 = 15V unless otherwise specified. (Note 3) PARAMETER CONDITIONS Soft-Start Source Current Ch 1/2 VFB1/2 = 2V, VSS1/2 = 0.07V Soft-Start VOH Ch 1/2 VFB1/2 = 2V l MIN TYP MAX UNITS 9.5 12 14.5 µA 1.9 2.15 2.4 V Soft-Start Sink Current Ch 1/2 VFB1/2 = 0.7V, VSS1/2 = 2V 0.7 1.4 2 mA Soft-Start VOL Ch 1/2 VFB1/2 = 0V 120 160 200 mV Soft-Start to Feedback Offset Ch 1/2 VVC1/2 = 1V, VSS1/2 = 0.4V Soft-Start Sink Current Ch 1/2 POR VFB1/2 = 2V, VSS1/2 = 0.14V (Note 7) l Soft-Start POR Threshold Soft-Start SW Disable Ch 1/2 VFB1/2 = 0V (Note 7) CMPI Bias Current Ch 1/2 VCMPI1/2 = 0.8V CMPO Leakage Ch 1/2 VCMPI1/2 = 0.8V, VCMPO1/2 = 40V, CMPI Threshold Ch 1/2 VCMPI1/2 Rising CMPI Threshold Ch 1/2 of VFB1/2 VCMPI1/2 Rising (Note 8) l –12 0 12 mV 150 400 600 µA 70 100 140 mV 95 115 150 mV –100 0 100 nA 70 500 nA 700 720 760 mV 86 90 94 % 85 mV CMPI Hysteresis Ch 1/2 VCMPI1/2 35 60 CMPO Sink Current Ch 1/2 VCMPI1/2 = 0.6V, VCMPO1/2 = 0.2V, 200 300 RT/SYNC Reference Current VRT/SYNC = 0.36V (E- and I-Grade) VRT/SYNC = 0.36V (H-Grade) 11.3 11.2 12 12 12.7 13 µA µA Minimum Switching Frequency RRT/SYNC =0Ω 50 110 150 kHz Switching Frequency RRT/SYNC = 28k 925 1 1075 kHz Maximum Switching Frequency RRT/SYNC =100k 2.25 2.5 3.0 MHz l l Switching Phase Angle Ch 1 ≥ Ch 2 µA 185 DIV Reference Current VDIV = 1V CH1 DIV 2 Threshold Deg 10.7 12 13.3 µA RRT/SYNC = 0V 0.44 0.5 0.56 V CH1 DIV 4 Threshold RRT/SYNC = 0V 0.89 1.0 1.06 V CH1 DIV 8 Threshold RRT/SYNC = 0V 1.39 1.5 1.56 V l 0.25 CLKOUT VOL CLKOUT VOH CLKOUT to SW1ON Delay ( tDCLKOSW1) CLKOUT Rising V 2 V 60 ns CLKOUT to SW2ON Delay ( tDCLKOSW2) CLKOUT Falling 30 ns RT/SYNC to CLKOUT Delay ( tDRTSYNCH) VRT/SYNC = 0V to 2V Rising Edge 300 ns RT/SYNC to CLKOUT Delay ( tDRTSYNCL) VRT/SYNC = 2V to 0V Falling Edge 150 ns SYNC Frequency Range SYNC Phase Angle Ch 1 to Ch 2 250 SYNC Frequency = 250kHz 2000 180 kHz Deg Minimum Switch On-Time Ch 1/2 140 ns Minimum Switch Off-Time Ch 1/2 200 ns 4 3692afc For more information www.linear.com/3692A LT3692A Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VVIN1/2 = 15V unless otherwise specified. (Note 3) PARAMETER CONDITIONS Minimum Boost for 100% DC Ch 1/2 (Note 9) IND + VOUT Current Ch 1/2 VVOUT1/2 = 0V VVOUT1/2 = 5V ILIM1/2 Reference Current VILIM = 0V IND to VOUT Maximum Current Ch 1/2 MIN TYP MAX 1.6 2.2 2.6 UNITS V 1.5 0.5 5 5 µA µA l 10 12 16 µA VILIM1/2 = 0V, VVOUT = 1V (Note 10) VILIM1/2 = 0V, VVOUT = 5V (Note 10) VILIM1/2 = 0.5V, VVOUT = 1V (Note 10) VILIM1/2 = 0.5V, VVOUT = 5V (Note 10) VILIM1/2 = 1.5V, VVOUT = 1V (Note 10) VILIM1/2 = 1.5V, VVOUT = 5V (Note 10) l l 0.8 1.25 1.4 1.8 3.7 3.7 1.8 2 2.2 2.6 4.6 4.6 2.6 3.0 3.6 3.8 5.8 5.8 A A A A A A l 1 10 Switch Leakage Current Ch 1/2 VSW1/2 = 0V Switch Saturation Voltage Ch 1/2 ISW1/2 = 500mA, VBST1/2 = 18V ISW1/2 = 3A, VBST1/2 = 18V Boost Current Ch 1/2 ISW1/2 = 500mA, VBST1/2 = 8V ISW1/2 = 3A, VBST1/2 = 8V 7 35 13 55 40 85 mA mA Minimum Boost Voltage Ch1/2 (Note 11) ISW1/2 = 3A, VBST1/2 = 8V 1.6 2.2 3.0 V Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: Absolute Maximum Voltage at VIN1/2 and SHDN1/2 pins is 60V for nonrepetitive 1 second transients and 40V for continuous operation. Note 3: The LT3692AEUH/LT3692AEFE is guaranteed to meet performance specifications from 0°C to 125°C junction temperature. Specifications over the –40°C to 125°C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. The LT3692AIUH/LT3692AIFE is guaranteed over the full –40°C to 125°C operating junction temperature range. The LT3692AHUH/LT3692AHFE is guaranteed over the full –40°C to 150°C operating junction temperature range. High junction temperatures degrade operating lifetimes. Operating lifetime is derated at junction temperatures greater than 125°C. Note 4: VIN undervoltage lockout is defined as the voltage which the VIN pin must exceed for operation. The threshold guarantees that internal bias lines are regulated and switching frequency is constant. Actual minimum input voltage to maintain a regulated output will depend upon output voltage and load current. See the Applications Information section. Note 5: VIN overvoltage lockout is defined as the voltage when exceeded halts converter operation. See the Applications Information section. 100 300 µA mV mV Note 6: The TJ output voltage represents the temperature at the center of the die while dissipating quiescent power. Due to switch power dissipation and temperature gradients across the die, the TJ output voltage measurement does not guarantee that absolute maximum junction temperature will not be exceeded. Note 7: An internal power on reset (POR) latch is set on the positive transition of the SHDN1/2 pin through its threshold, thermal shutdown or overvoltage lockout. The output of the latch activates current sources on each SS pin which typically sink 400µA and discharge the SS capacitor. The latch is reset when both SS pins are driven below the soft-start POR threshold or the SHDN pin is taken below its threshold. Note 8: The threshold is expressed as a percentage of the feedback reference voltage for the channel. Note 9: To enhance dropout operation, the output switch will be turned off for the minimum off-time only when the voltage across the boost capacitor drops below the minimum boost for 100% duty cycle threshold. Note 10: The IND to VOUT maximum current is defined as the value of current flowing from the IND pin to the VOUT pin which resets the switch latch when the VC pin is at its high clamp. Note 11: This is the minimum voltage across the boost capacitor needed to guarantee full saturation of the internal power switch. 3692afc For more information www.linear.com/3692A 5 LT3692A Typical Performance Characteristics VIN Overvoltage Threshold vs Temperature Shutdown Threshold and Minimum Input Voltage vs Temperature 3.5 41.0 5000 40.0 2.5 39.5 2.0 SHUTDOWN THRESHOLD VOLTAGE 1.5 4000 39.0 IQ (µA) VOLTAGE (V) 38.5 38.0 37.0 0.5 1000 36.5 0 –50 –25 0 36.0 –50 –25 25 50 75 100 125 150 TEMPERATURE (°C) 0 820 VSHDN1 = VSHDN2 = 0V CURRENT (µA) 5 4 3 2 815 0 –50 –25 6 1.25 4 1.00 2 OFFSET 810 0 –2 CH2 805 –4 CH1 IQ2 0 800 –50 –25 25 50 75 100 125 150 TEMPERATURE (°C) 0 3692A G04 4 420 –8 25 50 75 100 125 150 TEMPERATURE (°C) 390 385 380 375 370 –50 –30 –10 10 30 50 70 90 110 130 150 TEMPERATURE (°C) 3692A G07 TJ Output Voltage vs Temperature RTJ = 30k TO –1V –0.25 –0.50 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 3692A G06 Comparator Thresholds vs Temperature 750 VSS = 0.4V 740 730 1 0 –1 710 700 690 680 –2 670 –3 660 –4 –50 –25 RISING THRESHOLD 720 VOLTAGE (mV) VOLTAGE (mV) 395 0 1.4 0.25 RTJ = 30k TO GND 0 2 410 1.2 0.50 3 415 400 1 0.6 0.8 VOLTAGE (V) 0.75 Soft-Start-to-Feedback Offset vs Temperature 425 405 0.4 3692A G05 Error Amplifier Transconductance vs Temperature TRANSCONDUCTANCE (µMho) 1.50 –6 1 6 8 OFFSET VOLTAGE (mV) FEEDBACK VOLTAGE (V) 8 6 0.2 3692A G03 FB Voltage and CH1-CH2 FB Offset vs Temperature IQ1 0 3692A G02 Shutdown Quiescent Current vs Temperature 7 0 25 50 75 100 125 150 TEMPERATURE (°C) 3692A G01 9 –50°C 2000 125°C 37.5 1.0 25°C 150°C 3000 VOLTAGE (V) VOLTAGE (V) 6000 40.5 MINIMUM INPUT VOLTAGE 3.0 10 VIN1 Quiescent Current vs SHDN1 Voltage 25 50 75 100 125 150 TEMPERATURE (°C) 3692A G08 650 –50 –25 FALLING THRESHOLD 0 25 50 75 100 125 150 TEMPERATURE (°C) 3692A G09 3692afc For more information www.linear.com/3692A LT3692A Typical Performance Characteristics Comparator Sink Current vs Temperature SINK CURRENT AT VCMPO = 0.4V 191 1400 FREQUENCY (kHz) 300 250 200 150 RRT/SYNC = 28.0k 1000 800 600 400 50 200 0 189 1200 100 0 –50 –25 RRT/SYNC = 13.0k 185 183 179 0 –50 –25 25 50 75 100 125 150 TEMPERATURE (°C) 187 181 RRT/SYNC = 0k 0 177 175 –50 –25 25 50 75 100 125 150 TEMPERATURE (°C) CLKOUT-to-SW1 Delay vs Temperature Synchronization Duty Cycles vs Temperature 450 150 400 140 350 130 DELAY (ns) 100 100 90 SW1 300 CLKOUT 250 200 150 90 60 50 40 30 100 20 70 50 10 25 50 75 100 125 150 TEMPERATURE (°C) 0 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 3692A G13 0 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 3692A G15 Switch Saturation Voltage vs Temperature 1.8 300 1.6 ÷8 VOLTAGE (mV) 1.2 ÷4 1.0 0.8 0.6 ISW = 3A 250 1.4 ÷2 200 ISW = 1A 150 100 0.4 ISW = 500mA 50 0.2 0 –50 –25 MINIMUM RT/SYNC DUTY CYCLE 3695A G14 DIV Voltage Threshold vs Temperature VOLTAGE (V) 0 MAXIMUM RT/SYNC DUTY CYCLE 70 80 60 –50 –25 RT/SYNC FREQUENCY = 1MHz 80 DUTY CYCLE (%) 160 110 25 50 75 100 125 150 TEMPERATURE (°C) 3692A G12 RT/SYNC-to-CLKOUT and SW1 Delay vs Temperature 120 0 3692A G11 3692A G10 DELAY (ns) 193 RRT/SYNC = 44.2k 1600 350 CURRENT (µA) Switching Phase vs Temperature 195 1800 PHASE (DEG) 400 Switching Frequency vs Temperature 0 25 50 75 100 125 150 TEMPERATURE (°C) 0 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 3695A G16 3692A G17 3692afc For more information www.linear.com/3692A 7 LT3692A Typical Performance Characteristics Switch Peak Current vs Temperature 100 5.0 90 4.5 80 4.0 3A 60 50 40 30 10 0 2.50 VILIM = 0.5V 2.5 VILIM = 0V 2.0 1.5 0 –50 –25 0 1.00 –50 –25 25 50 75 100 125 150 TEMPERATURE (°C) 0 25 50 75 100 125 150 TEMPERATURE (°C) 3692A G20 5.0V Efficiency and Power Loss 3.3V Efficiency and Power Loss 90 2500 2250 85 2000 EFFICIENCY 3.0 90 2.5 85 3.0 2.5 1500 1250 1000 750 500 80 2.0 75 70 1.0 VIN = 12V FSW = 1MHz CH1 = 5V CH2 = 0V 65 250 0 10 20 30 40 50 60 70 RT/SYNC RESISTANCE (kΩ) 80 1.5 POWER LOSS 60 0 0.5 1.0 1.5 2.0 2.5 3.0 OUTPUT CURRENT (A) 3.5 2.0 75 1.5 POWER LOSS 70 0.5 65 0 60 1.0 0 0.5 VIN = 12V FREQ = 1MHz 0.5 CH1 = 3.3V CH2 = 0V 0 1 1.5 2 2.5 3 3.5 4 OUTPUT CURRENT (A) 3692A G22 3692A G21 2.5V Efficiency and Power Loss 3692A G23 1.8V Efficiency and Power Loss 3.0 2.5 80 80 2.0 75 2.0 75 1.5 70 1.5 EFFICIENCY 85 VIN = 12V FSW = 1MHz CH1 = 2.5V CH2 = 0V 65 60 1.0 0 0.5 1.0 1.5 2.0 2.5 3.0 OUTPUT CURRENT (A) 3.5 4 POWER LOSS 65 0.5 60 0 55 2.5 EFFICIENCY 1.0 VIN = 12V FSW = 1MHz CH1 = 1.8V CH2 = 0V 0 0.5 1.0 1.5 2.0 2.5 3.0 OUTPUT CURRENT (A) 3692A G24 PLOSS (W) POWER LOSS 70 EFFICIENCY (%) 85 PLOSS (W) 3.0 90 EFFICIENCY (%) 4 80 PLOSS (W) EFFICIENCY (%) 1750 EFFICIENCY (%) EFFICIENCY PLOSS (W) CLKOUT FREQUENCY (kHz) 1.75 3692A G19 CLKOUT Frequency vs RT/SYNC Resistance 8 2.00 1.25 0.5 3692A G18 0 2.25 1.50 1.0 25 50 75 100 125 150 TEMPERATURE (°C) ISW = 3A 2.75 VILIM = 1.5V 3.0 0.5A 0 –50 –25 3.00 3.5 1A 20 Minimum Boost Voltage vs Temperature VOLTAGE (V) 70 PEAK CURRENT (A) BOOST CURRENT (mA) Boost Current vs Temperature 3.5 0.5 4 0 3692A G25 3692afc For more information www.linear.com/3692A LT3692A Pin Functions BST1/BST2: The BST pin provides a higher than VIN base drive to the power NPN to ensure a low switch drop. If the voltage between the BST pin and the VIN pin is less than the voltage required to fully turn on the power NPN, the power switch is turned off to recharge the BST capacitor. CMPI1/CMPI2: The CMPI pin is an input to a comparator with a threshold of 720mV and 60mV of hysteresis. Connecting the CMPI pin to the FB pin will generate a power good signal when the output is within 90% of its regulated value. CMPO1/CMPO2: The CMPO pin is an open-collector output that sinks current when the CMPI pin falls below its threshold. For a typical input voltage above 2.8V, its output state remains true, although during shutdown, VIN1 undervoltage lockout or thermal shutdown, its current sink capability is reduced. The COMPO pins can be left open circuit or tied together to form a single power good signal. DIV: The voltage present at the DIV pin determines the ratio of channel 1 frequency to the master clock frequency set by the RT/SYNC pin. The DIV pin is driven by an internal current source with a typical value of 12µA which allows a single resistor from the DIV pin to ground to set the DIV voltage and resulting channel 1 frequency divider. Ratios of 1, 2, 4 and 8 are available. See the Applications Information section for more information. DNC: Do Not Connect. GND: The exposed pad pin is the only ground connection for the device. The exposed pad should be soldered to a large copper area to reduce thermal resistance. The GND pin is common to both channels and also serves as small-signal ground. For ideal operation all small-signal ground paths should connect to the GND pin at a single point avoiding any high current ground returns. ILIM1/ILIM2: The voltage present at the ILIM pin determines the peak inductor current for the channel. The ILIM pin is driven by an internal current source with a typical value of 12µA. A resistor from the ILIM pin to ground sets the ILIM voltage. The maximum current limit range is 4.8A to 2A when the ILIM voltages are 1.5V and 0V respectively. IND1/IND2: The IND pin is the input to the internal sense resistor that measures current flowing in the inductor. When the current in the resistor exceeds the current dictated by the VC pin, the SW latch is held in reset, disabling the output switch. Bias current flows out of the IND pin. RT/SYNC: The voltage present at the RT/SYNC pin determines the constant switching frequency. The RT/SYNC pin is driven by an internal current source with a typical value of 12µA which allows a single resistor from the RT/ SYNC pin to ground to set the RT/SYNC voltage and resulting switching frequency. Minimum switching frequency is typically 110kHz when VRT/SYNC is 0V and maximum switching frequency is typically 2.5MHz when VRT/SYNC is above 950mV. Driving the RT/SYNC pin with an external clock signal will synchronize the switch to the applied frequency. Synchronization occurs on the rising edge of the clock signal after the clock signal is detected. Each rising clock edge initiates an oscillator ramp reset. A gain control loop servos the oscillator charging current to maintain constant oscillator amplitude. Hence, the slope compensation and channel phase relationship remain unchanged. If the clock signal is removed, the oscillator reverts to resistor mode after the synchronization detection circuitry times out. The clock source impedance should be set such that the current out of the RT/SYNC pin in resistor mode generates a frequency roughly equivalent to the synchronization frequency. See the Applications Information section for more information. FB1/FB2: The FB pin is the negative input to the error amplifier. The output switches to regulate this pin to 806mV with respect to the exposed ground pad. Bias current flows out of the FB pin. 3692afc For more information www.linear.com/3692A 9 LT3692A pin functions SHDN1/SHDN2: The shutdown pin is used to control each channel’s operation. In addition to controlling channel 1, the SHDN1 pin also activates control circuitry for both channels and must be present for channel 2 to operate. When SHDN1 is below its threshold, switching on both channels is halted. Further reducing the SHDN1 voltage to 0.6V reduces the quiescent current to a typical value of 6µA Independent channel UVLO can be programmed by connecting the SHDN pin to an input voltage divider. See the Applications Information section for more information. If the shutdown features are not used, the SHDN pin should be tied to VIN. SS1/SS2: Current flowing out the SS pin into an external capacitor defines the rise time of the output voltage. When the SS pin is lower than the 0.806V reference, the feedback is regulated to the SS voltage. When the SS pin exceeds the reference voltage, the output will regulate the FB pin voltage to 0.806V and the SS pin will continue to rise until its clamp voltage. During an output overload, the VC pin is driven above the maximum switch current level activating its voltage clamp. When the VC clamp is activated, the SS pin is discharged until the output reaches a regulation point that the maximum output current can maintain. When the overload condition is removed, the output soft starts from that voltage. In the case of a SHDN or thermal shutdown event, a power on reset latch ensures the capacitors on both channels are fully discharged before either is released. Connecting both SS pins together ensures the outputs track together. CLKOUT: The CLKOUT pin generates a square wave of 0V to 2.5V which is synchronized to the internal oscillator. If the switching frequency is set by an external resistor the resultant clock duty cycle will be 50%. If the RT/SYNC pin is driven by an external clock source, the resultant CLKOUT duty cycle will mirror the external source. 10 SW1/SW2: The SW pin is the emitter of the internal power NPN. At switch off, the inductor will drive this pin below ground with a high dV/dt. An external Schottky catch diode to ground, close to the SW pin and respective VIN decoupling capacitor’s ground, must be used to prevent this pin from excessive negative voltages. TJ: The TJ pin outputs a voltage proportional to junction temperature. The pin is 250mV for 25°C and has a slope of 10mV/°C. See the Applications Information section for more information. VC1/VC2: The VC pin is the output of the error amplifier and the input to the peak switch current comparator. It is normally used for frequency compensation, but can also be used as a current clamp or control loop override. If the error amplifier drives VC above the maximum switch current level, a voltage clamp activates. This indicates that the output is overloaded and current is pulled from the SS pin reducing the regulation point. VIN1: The VIN1 pin powers the internal control circuitry for both channels and is monitored by overvoltage/undervoltage lockout comparators. The VIN1 pin is also connected to the collector of channel 1’s on-chip power NPN switch. The VIN1 pin has high dI/dt edges and must be decoupled to ground close to the pin of the device. VIN2: The VIN2 pin powers the output stage for channel 2 and is monitored by overvoltage/undervoltage lockout comparators. VIN1 voltage must be greater than typically 2.8V for VIN2 operation. The VIN2 pin is also the collector of channel 2’s on-chip power NPN switch. The VIN2 pin has high dI/dt edges and must be decoupled to ground close to the pin of the device. VOUT1/VOUT2: The VOUT pin is the output to the internal sense resistor that measures current flowing in the inductor. When the current in the resistor exceeds the current dictated by the VC pin, the SW latch is held in reset disabling the output switch. Bias current flows out of the VOUT pin. 3692afc For more information www.linear.com/3692A LT3692A Block Diagram VIN1 1.32V SHDN1 + – + – VIN1 39V CHANNEL 1 THERMAL SHUTDOWN 2.5V 12µA SS1 S – + 90mV – + S PRE PRE Q R DROPOUT ENHANCEMENT BST1 DRIVER CIRCUITRY SW1 IND1 + – Q R VOUT1 VC1 R1 FB1 2.5V ILIM1 RLIM CMPI1 12µA SLOPE COMPENSATION 2.5V 2.5V DIV 0.806V 0.72V CMPO1 + – 12µA RT/SYNC R3 + + – R2 12µA OSCILLATOR AND AGC CLK1 VIN1 MASTER CLOCK 2.8V + – CLK2 TO CHANNEL 2 INTERNAL REGULATOR AND REFERENCES 2.5V TJ CLKOUT GND RDIV 3692a F01 Figure 1. LT3692A Block Diagram Applications Information The LT3692A is a dual channel, constant frequency, current mode buck converter with internal 3.8A switches. Each channel can be independently controlled with the exception that VIN1 must be above the typically 2.8V undervoltage lockout threshold to power the common internal regulator, oscillator and thermometer circuitry. If the SHDN1 pin is taken below its 1.32V threshold switching on both channels will be disabled. Further reducing the SHDN1 below a typical value of 0.6V will place the LT3692A in a low quiescent current mode. In this mode the LT3692A typically draws 6µA from VIN1 and <1µA from VIN2. When the SHDN pin is driven above 1.32V, the internal bias circuits turn on generating an internal regulated voltage, 0.806VFB, 12µA RT/SYNC, DIV and ILIM current references, and a POR signal which sets the soft-start latch. Once the internal reference reaches its regulation point, the internal oscillator will start generating a master clock signal for the two regulators at a frequency determined by the voltage present at the RT/SYNC pin. The channel 1 clock is then divided by 1, 2, 4 or 8 depending on the voltage present at the DIV pin. Channel 2’s clock runs at the master clock frequency with a 180° phase shift from channel 1. Alternatively, if a synchronization signal is detected by the LT3692A the RT/SYNC pin, the master clock will be generated at the incoming frequency on the rising edge of the synchronization pulse with channel 1 in phase with the synchronization signal. Frequency division and phase remains the same as the internally generated master clock. In addition, the internal slope compensation will be automatically adjusted to prevent subharmonic oscillation 3692afc For more information www.linear.com/3692A 11 LT3692A Applications Information during synchronization. In either mode of oscillator operation, a square wave with the master clock frequency, synchronized to channel 1 is present at the CLKOUT pin. The two regulators are constant frequency, current mode step-down converters. Current mode regulators are controlled by an internal clock and two feedback loops that control the duty cycle of the power switch. In addition to the normal error amplifier, there is a current sense amplifier that monitors switch current on a cycle-by-cycle basis. This technique means that the error amplifier commands current to be delivered to the output rather than voltage. A voltage fed system will have low phase shift up to the resonant frequency of the inductor and output capacitor, then an abrupt 180° shift will occur. The current fed system will have 90° phase shift at a much lower frequency, but will not have the additional 90° shift until well beyond the LC resonant frequency. This makes it much easier to frequency compensate the feedback loop and also gives much quicker transient response. The Block Diagram in Figure 1 shows only one of the switching regulators whose operation will be discussed below. The additional regulator will operate in a similar manner with the exception that its clock will be 180° outof-phase with the other regulator. When, during power-up, an internal POR signal sets the soft-start latch, both SS pins will be discharged to ground to ensure proper start-up operation. When the SS pin voltage drops below 100mV, the VC pin is driven low disabling switching and the soft-start latch is reset. Once the latch is reset the soft-start capacitor starts to charge with a typical value of 12µA. As the voltage rises above 115mV on the SS pin, the VC pin will be driven high by the error amplifier. When the voltage on the VC pin exceeds 0.9V, the clock set-pulse sets the driver flip-flop, which turns on the internal power NPN switch. This causes current from VIN, through the NPN switch, inductor and internal sense resistor to increase. When the voltage drop across the internal sense resistor exceeds a predetermined level set by the voltage on the VC pin, the flip-flop is reset and the internal NPN switch is turned off. Once the switch is turned off the inductor will drive the voltage at the SW pin low until the external Schottky diode starts to conduct, decreasing the current 12 in the inductor. The cycle is repeated with the start of each clock cycle. However, if the internal sense resistor voltage exceeds the predetermined level at the start of a clock cycle, the flip-flop will not be set resulting in a further decrease in inductor current. Since the output current is controlled by the VC voltage, output regulation is achieved by the error amplifier continually adjusting the VC pin voltage. The error amplifier is a transconductance amplifier that compares the FB voltage to the lowest voltage present at either the SS pin or an internal 806mV reference. Compensation of the loop is easily achieved with a simple capacitor or series resistor/capacitor from the VC pin to ground. The regulators’ maximum output current occurs when the VC pin is driven to its maximum clamp value by the error amplifier. The value of the typical maximum switch current can be programmed from 4.8A to 2A by placing a resistor from the ILIM pin to ground. Since the SS pin is driven by a constant current source, a single capacitor on the soft-start pin will generate controlled linear ramp on the output voltage. If the current demanded by the output exceeds the maximum current dictated by the VC pin clamp, the SS pin will be discharged, lowering the regulation point until the output voltage can be supported by the maximum current. Once the overload condition is removed, the regulator will soft-start from the overload regulation point. Shutdown control, VIN overvoltage, or thermal shutdown will set the soft-start latch, resulting in a complete softstart sequence. The switch driver operates from either the VIN or BST voltage. An external diode and capacitor are used to generate a drive voltage higher than VIN to saturate the output NPN and maintain high efficiency. If the BST capacitor voltage is sufficient, the switch is allowed to operate to 100% duty cycle. If the boost capacitor discharges towards a level insufficient to drive the output NPN, a BST pin comparator forces a minimum cycle off time, allowing the boost capacitor to recharge. A comparator with a threshold of 720mV and 60mV of hysteresis is provided for detecting error conditions. The CMPO output is an open-collector NPN that is off when the CMPI pin is above the threshold allowing a resistor to pull the CMPO pin to a desired voltage. 3692afc For more information www.linear.com/3692A LT3692A Applications Information The voltage present at the TJ pin is proportional to the junction temperature of the LT3692A. The TJ pin will be 250mV for a die temperature of 25°C and will have a slope of 10mV/°C. Choosing the Output Voltage The output voltage is programmed with a resistor divider between the output and the FB pin. Choose the 1% resistors according to: V R1= R2 • OUT – 1 0.806 R2 should be 10k or less to avoid bias current errors. Reference designators refer to the Block Diagram in Figure 1. To alleviate duty cycle restrictions due to minimum switchon times, channel 1’s switching frequency can be divided from the master clock by 1, 2, 4 or 8 determined by resistor RDIV in Figure 1. Channel 2’s switching frequency is not affected by the DIV pin. The DIV pin is driven by a 12µA current source. Setting resistor RDIV sets the voltage present at the DIV pin which determines the divisor as shown in Table 1. The DIV pin doesn’t have any input hysteresis near the ratio thresholds. Table 1. Channel 1 Divisor vs VDIV Choosing the Switching Frequency The LT3692A switching frequency is set by resistor R3 in Figure 1. The RT/SYNC pin is driven by a 12µA current source. Setting resistor R3 sets the voltage present at the RT/SYNC pin which determines the master oscillator frequency as illustrated in Figure 2. The R3 resistance (in kΩ) may be calculated from the desired switching frequency (in kHz) by the equation: R3 = 1.86E-6 • FSW2 + 2.81E-2 • FSW –1.76 2500 DIV VOLTAGE 2000 1750 RDIV VDIV < 0.5V 1 0 0.5V < VDIV < 1.0V 2 61.9k 1.0V < VDIV < 1.5V 4 102k 1.5V < VDIV 8 150k The switching frequency is typically set as high as possible to reduce overall solution size. The LT3692A employs techniques to enhance dropout at high frequencies but efficiency and maximum input voltage decrease due to switching losses and minimum switch-on times. Frequency (Hz) = 1500 1250 1000 VOUT + VD 1 • VIN – VSW + VD tON(MIN) where VD is the forward voltage drop of the catch diode (D1 Figure 2), VSW is the voltage drop of the internal switch, and tON(MIN) in the minimum on-time of the switch. 750 500 250 0 FREQUENCY RATIO The maximum recommended frequency can be approximated by the equation: 2250 CLKOUT FREQUENCY (kHz) for frequencies between 150kHz and 2250kHz. A 0V to 2.5V square wave with the same frequency as the master oscillator and in phase with channel 1 is output via the CLKOUT pin. The CLKOUT signal can be used to synchronize multiple switching regulators. 0 10 20 30 40 50 60 70 RT/SYNC RESISTANCE (kΩ) 80 3692a F02 Figure 2. Switching Frequency vs RT/SYNC Resistance 3692afc For more information www.linear.com/3692A 13 LT3692A Applications Information Table 2. Efficiency and Size Comparisons for Different RRT/SYNC Values, 3.3V Output FREQUENCY RT/SYNC EFFICIENCY VVIN1/2 = 12V VIN(MAX)† L* C* C + L (Area) 250kHz 5.90k 88% 39V 12µH 120µF 59.8mm2 500kHz 13.0k 87% 39V 5.6µH 60µF 54.6mm2 1000kHz 28.0k 84% 26V 3.3µH 30µF 51.9mm2 1500kHz 44.2k 82% 18V 1.5µH 22µF 46.9mm2 2250kHz 69.8k 78% 12V 1µH 15µF 19.1mm2 †V IN(MAX) is defined as the highest typical input voltage that maintains constant output voltage ripple. * Inductor and capacitor values chosen for stability and constant ripple current. The following example along with the data in Table 2 illustrates the trade-offs of switch frequency selection for a single input voltage system. Example. VIN = 25V, VOUT = 3.3V, IOUT = 2.5A, tON(MIN) = 140ns, VD = 0.6V, VSW = 0.4V: Max Frequency = 3.3 + 0.6 1 • ~ 1.1MHz 25 – 0.4 + 0.6 140ns RT/SYNC ~ 31.6kΩ (Figure 2 ) Input Voltage Range Once the switching frequency has been determined, the input voltage range of the regulator can be determined. The minimum input voltage is determined by either the LT3692A’s minimum operating voltage of ~2.8V, or by its maximum duty cycle. The duty cycle is the fraction of time that the internal switch is on during a clock cycle. Unlike most fixed frequency regulators, the LT3692A will not switch off at the end of each clock cycle if there is sufficient voltage across the boost capacitor (C3 in Figure 1) to fully saturate the output switch. Forcing switch-off for a minimum time will only occur at the end of a clock cycle when the boost capacitor needs to be recharged. This operation has the same effect as lowering the clock frequency for a fixed off time, resulting in a higher duty cycle and lower minimum input voltage. The resultant duty cycle depends on the charging times of the boost capacitor and can be approximated by the following equation: DCMAX = 1 1 B where B is 3A divided by the typical boost current from the Electrical Characteristics table. 1+ This leads to a minimum input voltage of: VIN(MIN) = VOUT + VD – VD + VSW DCMAX where VSW is the voltage drop of the internal switch. Figure 4 shows a typical graph of minimum input voltage vs load current for the 3.3V output shown in Figure 15. 6 tP VOUT = 3.3V 5 START-UP tP/2 VOLTAGE (V) SW1 tP SW2 tP/2 tP 2 0 3692a F03 0 tDCLKOSW2 500 1000 1500 2000 2500 3000 3500 CURRENT (mA) 3692a F04 Figure 3. Timing Diagram RT/SYNC = 28.0k, tP = 1µs, VDIV = 0V 14 3 1 CLKOUT tDCLKOSW1 RUNNING 4 Figure 4. Minimum Input Voltage vs Load Current 3692afc For more information www.linear.com/3692A LT3692A Applications Information The maximum input voltage is determined by the absolute maximum ratings of the VIN and BST pins and by the frequency and minimum duty cycle. The minimum duty cycle is defined as: DCMIN = tON(MIN) • Frequency Maximum input voltage as: VIN(MAX) = VOUT + VD – VD + VSW DCMIN In cases where multiple input voltages are present, or the VIN/VOUT ratio for channel 1 is significantly different than channel 2, channel 1’s frequency can be divided by a factor of 2, 4 or 8 from the programmed value by setting the DIV pin resistor to the appropriate value. Dividing channel 1’s frequency will increase the maximum input voltage by the same ratio. Channel 1’s external components will have to be chosen according to the resulting frequency. Example: Note that the LT3692A will regulate if the input voltage is taken above the calculated maximum voltage as long as maximum ratings of the VIN and BST pins are not violated. However operation in this region of input voltage will exhibit pulse-skipping behavior. VOUT = 3.3V, IOUT = 1A, frequency = 1MHz, temperature = 25°C, VSW = 0.1V, B = 50 (from boost characteristics specification), VD = 0.4V, tON(MIN) = 140ns. VDIV = 0.75V. DCMIN1 = tON(MIN1) • Frequency/2 = 0.07 VIN1(MAX) = Example: VOUT = 3.3V, IOUT = 1A, frequency = 1MHz, temperature = 25°C, VSW = 0.1V, B = 50 (from boost characteristics specification), VD = 0.4V, tON(MIN) = 140ns: DCMAX = 1 1+ VIN(MIN) = 1 50 = 98% 3.3 + 0.4 – 0.4 + 0.1= 26.1V 0.14 If the maximum load for a single channel is lower than 2.5A, then you can decrease the value of the inductor and operate with higher ripple current, or you can adjust the maximum switch current for the channel via the ILIM pin. This allows you to use a physically smaller inductor, or one with a lower DCR resulting in higher efficiency. SW1 tP SW2 tP/2 VOUT f With this value the maximum load current will be ~3.5A, independent of input voltage. The inductor’s RMS current rating must be greater than your maximum load current and its saturation current should be higher than the maximum peak switch current, and will reduce the output voltage ripple. 2 • tP The peak inductor and switch current is: tP CLKOUT tDCLKOSW1 A good first choice for the LT3692A inductor value is: where f is frequency in MHz and L is in µH. 3.3 + 0.4 – 0.4 + 0.1= 3.48V 0.98 1/(2 • tP) Inductor Selection and Maximum Output Current L= DCMIN = tON(MIN) • Frequency = 0.14 VIN(MAX) = 3.3 + 0.4 – 0.4 + 0.1= >39V 0.07 3692a F05 tDCLKOSW2 Figure 5. Timing Diagram RT/SYNC = 28.0k, tP = 1µs, VDIV = 0.75V ISW(PK) = IL(PK) = IOUT + ∆IL 2 To maintain output regulation, this peak current must be less than the LT3692A’s switch current limit, ILIM. ILIM 3692afc For more information www.linear.com/3692A 15 LT3692A Applications Information can be set between 2A and 4.8A for each channel via a resistor from the ILIM pin to ground. The ILIM pin is driven by a 12µA current source. Setting resistor R LIM sets the voltage present at the ILIM pin which determines the maximum switch current as illustrated in Figure 6. A capacitor from the ILIM pin to ground, or a resistor divider from the output, can be used to limit the peak current during start-up. If a capacitor is used it must be discharged before power-up to ensure proper operation (see 3.3V and 2.5V Dual Step-Down Converter in Typical Applications). Referring to Figure 6, as the peak current limit is reduced, slope compensation further reduces the peak current with increasing duty cycle. When the ILIM pin is used to reduce the peak switch current, the equation for inductor choice becomes: 50 • VOUT L= for RILIM > 24.9kΩ f • RILIM where f is frequency in MHz, L in µH and R in kΩ. 4.5 PEAK SWITCH CURRENT (A) 4.0 3.5 When the LT3692A’s input supplies are operated at different input voltages, an input capacitor sized for that channel should be placed as close as possible to the respective VIN pins. A caution regarding the use of ceramic capacitors at the input. A ceramic input capacitor can combine with stray inductance to form a resonant tank circuit. If power is applied quickly (for example by plugging the circuit into a live power source) this tank can ring, doubling the input voltage and damaging the LT3692A. The solution is to either clamp the input voltage or dampen the tank circuit by adding a lossy capacitor in parallel with the ceramic capacitor. For details, see Application Note 88. Output Capacitor Selection Typically step-down regulators are easily compensated with an output crossover frequency that is 1/10 of the switching frequency. This means that the time that the output capacitor must supply the output load during a transient step is ~2 or 3 switching periods. With an allowable 1% drop in output voltage during the step, a good starting value for the output capacitor can be expressed by: CVOUT = 3.0 2.5 Example: 2.0 VOUT = 3.3V, Frequency = 1MHz, Max Load Step = 2A. 1.5 1.0 CVOUT = 0 10 20 30 40 50 60 70 80 90 100 ILIM PIN RESISTOR (kΩ) 3692a F06 Figure 6. Peak Switch Current vs ILIM Resistor Input Capacitor Selection Bypass the inputs of the LT3692A circuit with a 4.7µF or higher ceramic capacitor of X7R or X5R type. A lower value or a less expensive Y5V type can be used if there is additional bypassing provided by bulk electrolytic or tantalum capacitors. 16 Max Load Step Frequency • 0.01• VOUT 2 = 60µF 1E6 • 0.01• 3.3V The calculated value is only a suggested starting value. Increase the value if transient response needs improvement or reduce the capacitance if size is a priority. The output capacitor filters the inductor current to generate an output with low voltage ripple. It also stores energy in order to satisfy transient loads and to stabilize the LT3692A’s control loop. The switching frequency of the LT3692A determines the value of output capacitance required. Also, the current mode control loop doesn’t require the presence of output capacitor series resistance (ESR). For these reasons, you are free to use ceramic capacitors to achieve very low output ripple and small circuit size. 3692afc For more information www.linear.com/3692A LT3692A Applications Information You can also use electrolytic capacitors. The ESRs of most aluminum electrolytics are too large to deliver low output ripple. Tantalum and newer, lower ESR organic electrolytic capacitors intended for power supply use, are suitable and the manufacturers will specify the ESR. The choice of capacitor value will be based on the ESR required for low ripple. Because the volume of the capacitor determines its ESR, both the size and the value will be larger than a ceramic capacitor that would give you similar ripple performance. One benefit is that the larger capacitance may give better transient response for large changes in load current. Table 3 lists several capacitor vendors. Table 3 VENDOR TYPE Taiyo Yuden Ceramic X5R, X7R SERIES AVX Ceramic X5R, X7R Tantalum Kemet Tantalum TA Organic AL Organic T491, T494, T495 T520 A700 Sanyo TA/AL Organic POSCAP Panasonic AL Organic SP CAP TDK Ceramic X5R, X7R Catch Diode The diode D1 conducts current only during switch-off time. Use a Schottky diode to limit forward voltage drop to increase efficiency. The Schottky diode must have a peak reverse voltage that is equal to regulator input voltage and sized for average forward current in normal operation. Average forward current can be calculated from: ID(AVG) = IOUT • ( VIN – VOUT ) VIN With a shorted condition, diode current will increase to the typical value determined by the peak switch current limit of the LT3692A set by the ILIM pin. This is safe for short periods of time, but it would be prudent to check with the diode manufacturer if continuous operation under these conditions can be tolerated. BST Pin Considerations The capacitor and diode tied to the BST pin generate a voltage that is higher than the input voltage. In most cases a 0.47µF capacitor and a small Schottky diode (such as the CMDSH-4E) will work well. To ensure optimal performance at duty cycles greater than 80%, use a 0.5A Schottky diode (such as a PMEG4005). Almost any type of film or ceramic capacitor is suitable, but the ESR should be <1Ω to ensure it can be fully recharged during the off time of the switch. The capacitor value can be approximated by: CBST = IOUT(MAX) • VOUT 5 • VIN ( VOUT – 2) • f where IOUT(MAX) is the maximum load current. Figure 7 shows four ways to arrange the boost circuit. The BST pin must be more than 3V above the SW pin for full efficiency. Generally, for outputs of 3.3V and higher the standard circuit (Figure 7a) is the best. For lower output voltages the boost diode can be tied to the input (Figure 7b). The circuit in Figure 7a is more efficient because the BST pin current comes from a lower voltage source. Figure 7c shows the boost voltage source from available DC sources that are greater than 3V. The highest efficiency is attained by choosing the lowest boost voltage above 3V. For example, if you are generating 3.3V and 1.8V and the 3.3V is on whenever the 1.8V is on, the 1.8V boost diode can be connected to the 3.3V output. In any case, you must also be sure that the maximum voltage at the BST pin is less than the maximum specified in the Absolute Maximum Ratings section. The boost circuit can also run directly from a DC voltage that is higher than the input voltage by more than 3V, as in Figure 7d. The diode is used to prevent damage to the LT3692A in case VX is held low while VIN is present. The circuit saves several components (both BST pins can be tied to D2). However, efficiency may be lower and dissipation in the LT3692A may be higher. Also, if VX is absent, the LT3692A will still attempt to regulate the output, but will do so with very low efficiency and high dissipation because the switch will not be able to saturate, dropping 1.5V to 2V in conduction. 3692afc For more information www.linear.com/3692A 17 LT3692A Applications Information D2 VIN VIN BST C3 D2 VIN SW VIN LT3692A GND (7b) D2 VX > VIN + 3V VIN BST C3 VIN SW VIN BST SW LT3692A LT3692A IND VOUT VBST – VSW = VX VBST(MAX) = VIN + VX VX(MIN) = 3V VOUT < 3V GND VBST – VSW = VIN VBST(MAX) = 2 • VIN D2 VIN SW IND VOUT VOUT (7a) VX = LOWEST VIN OR VOUT > 3V C3 LT3692A IND VOUT VBST – VSW = VOUT VBST(MAX) = VIN + VOUT BST IND VOUT VOUT < 3V GND VBST – VSW = VX VBST(MAX) = VX VX(MIN) = VIN + 3V (7c) VOUT < 3V GND 3692a F07 (7d) Figure 7. BST Pin Considerations The minimum input voltage of an LT3692A application is limited by the minimum operating voltage (typically 2.8V) and by the maximum duty cycle as outlined above. For proper start-up, the minimum input voltage is also limited by the boost circuit. If the input voltage is ramped slowly, or the LT3692A is turned on with its SS pin when the output is already in regulation, then the boost capacitor may not be fully charged. Because the boost capacitor is charged with the energy stored in the inductor, the circuit will rely on some minimum load current to get the boost circuit running properly. This minimum load will depend on input and output voltages, and on the arrangement of the boost circuit. The Typical Performance Characteristics section shows plots of the minimum load current to start and to run as a function of input voltage for 3.3V outputs. In many cases the discharged output capacitor will present a load to the switcher which will allow it to start. The plots show the worst-case situation where VIN is ramping very slowly. Use a Schottky diode for the lowest start-up voltage. 18 Outputs Greater Than 6V For outputs greater than 6V, add a resistor of 1k to 2.5k across the inductor to damp the discontinuous ringing of the SW node, preventing unintended SW current. The 12V output circuit in the Typical Applications section shows the location of this resistor. Frequency Compensation The LT3692A uses current mode control to regulate the output. This simplifies loop compensation. In particular, the LT3692A does not require the ESR of the output capacitor for stability so you are free to use ceramic capacitors to achieve low output ripple and small circuit size. Frequency compensation is provided by the components tied to the VC pin. Generally a capacitor and a resistor in series to ground determine loop gain. In addition, there is a lower value capacitor in parallel. This capacitor is not part of the loop compensation but is used to filter noise at the switching frequency. 3692afc For more information www.linear.com/3692A LT3692A Applications Information Loop compensation determines the stability and transient performance. Designing the compensation network is a bit complicated and the best values depend on the application and in particular the type of output capacitor. A practical approach is to start with one of the circuits in this data sheet that is similar to your application and tune the compensation network to optimize the performance. Stability should then be checked across all operating conditions, including load current, input voltage and temperature. The LT1375 data sheet contains a more thorough discussion of loop compensation and describes how to test the stability using a transient load. Figure 8 shows an equivalent circuit for the LT3692A control loop. The error amp is a transconductance amplifier with finite output impedance. The power section, consisting of the modulator, power switch and inductor, is modeled as a transconductance amplifier generating an output current proportional to the voltage at the VC pin. Note that the output capacitor integrates this current, and that the capacitor on the VC pin (CC) integrates the error amplifier output current, resulting in two poles in the loop. In most cases a zero is required and comes from either the output capacitor ESR or from a resistor in series with CC. This simple model works well as long as the value of the inductor is not too high and the loop crossover frequency is much lower than the switching frequency. A phase lead capacitor (CPL) across the feedback divider may improve the transient response. Synchronization The RT/SYNC pin can also be used to synchronize the regulators to an external clock source. Driving the RT/SYNC resistor with a clock source triggers the synchronization detection circuitry. Once synchronization is detected, the rising edge of SW1 will be synchronized to the rising edge of the RT/SYNC signal and the rising edge of SW2 synchronized to the falling edge of the RT/SYNC signal (see Figures 10 and 11). During synchronization, a 0V to 2.4V square wave with the same frequency and duty cycle as the synchronization signal is output via the CLKOUT pin with a typical propagation delay of 250ns. In addition, an internal AGC loop will adjust slope compensation to avoid subharmonic oscillation. If the synchronization signal is halted, the synchronization detection circuitry will timeout in typically 10µs at which time the LT3692A reverts to the free-running frequency based on the RT/SYNC pin voltage. The synchronizing clock signal input to the LT3692A must have a frequency between 200kHz and 2MHz, a duty cycle between 20% and 80%, a low state below 0.5V and a high state above 1.6V. Synchronization signals outside of these parameters will cause erratic switching behavior. If the RT/SYNC pin is held above 1.6V at any time, switching will be disabled. If the synchronization signal is not present during regulator start-up (for example, the synchronization circuitry is powered from the regulator output) the RT/SYNC pin must remain below 1V until the synchronization circuitry is active for proper start-up operation. LT3692A CURRENT MODE POWER STAGE gm = 4.8mho OUTPUT gm = 400µmho 3.6M RC CF CC + – VC ERROR AMP R1 CPL ESR FB C1 + 0.806V R2 C1 CERAMIC TANTALUM OR POLYMER 3692a F08 Figure 8. Model for Loop Response 3692afc For more information www.linear.com/3692A 19 LT3692A Applications Information If the synchronization signal powers up in an undetermined state (VOL, VOH, Hi-Z), connect the synchronization clock to the LT3692A as shown in Figure 9. The circuit as shown will isolate the synchronization signal when the output voltage is below 90% of the regulated output. The LT3692A will start up with a switching frequency determined by the resistor from the RT/SYNC pin to ground. VOUT1 LT3692A PG1 RT/SYNC If the synchronization signal powers up in a low impedance state (VOL), connect a resistor between the RT/SYNC pin and the synchronizing clock. The equivalent resistance seen from the RT/SYNC pin to ground will set the startup frequency. If the synchronization signal powers up in a high impedance state (Hi-Z), connect a resistor from the RT/SYNC pin to ground. The equivalent resistance seen from the RT/SYNC pin to ground will set the start-up frequency. VCC SYNCHRONIZATION CIRCUITRY CLK 3692a F09 Figure 9. Synchronous Signal Powered from Regulator’s Output tP tP SW1 SW1 tP/2 tP tP SW2 SW2 tP tP/2 tPON CLKOUT CLKOUT tDCLKOSW1 tDCLKOSW1 tDCLKOSW2 tP/2 tP tDCLKOSW2 tPON tP RT/SYNC RT/SYNC 3692a F10 tDRTSYNC Figure 10. Timing Diagram RT/SYNC = 1MHz, Duty Cycle = 50% 20 tP 3692a F11 tDRTSYNCH tDRTSYNCH Figure 11. Timing Diagram RT/SYNC = 1MHz, Duty Cycle > 50% 3692afc For more information www.linear.com/3692A LT3692A Applications Information Reducing Input Ripple Voltage Shutdown and Undervoltage/Overvoltage Lockout Synchronizing the switches to the rising and falling edges of the synchronization signal provides the unique ability to reduce input ripple currents in systems where VIN1 and VIN2 are connected to the same supply. Decreasing the input current ripple reduces the required input capacitance. For example, the input ripple voltage shown in Figure 12 for a typical antiphase dual 14.4V to 8.5V and 14.4V to 3.3V regulator is decreased from a peak of 472mV to 160mV as shown in Figure 13 by driving the LT3692A with a 71% duty cycle synchronization signal. Typically, undervoltage lockout (UVLO) is used in situations where the input supply is current limited, or has a relatively high source resistance. A switching regulator draws constant power from the source, so source current increases as source voltage drops. This looks like a negative resistance load to the source and can cause the source to current limit or latch low under low source voltage conditions. UVLO prevents the regulator from operating at source voltages where these problems might occur. SW1 Overvoltage lockout (OVLO) is typically used to shut down the switching regulator during potentially harmful input voltage transients. The overvoltage lockout threshold is typically 39V. Each channel of the LT3692A is forced into shutdown when its input voltage exceeds 39V, and will survive voltages as high as 60V. When the input voltage drops back below 39V, the LT3692A goes through a POR cycle and the output soft-starts from its existing level to its regulation point. SW2 INPUT RIPPLE V RT/SYNC 3692a F12 Figure 12. Dual 14.4V/8.5V, 14.4V/3.3V with 180° Phase SW1 SW2 Additionally, an internal comparator will force both channels into shutdown below the minimum VIN1 of 2.8V. This feature can be used to prevent excessive discharge of battery-operated systems. In addition to the VIN1 undervoltage lockout, both channels will be disabled when SHDN1 is less than 1.32V. Programmable UVLO may be implemented using an input voltage divider and one of the internal comparators (see the Typical Applications section). INPUT RIPPLE V RT/SYNC 3692a F13 Figure 13. Dual 14.4V/8.5V, 14.4V/3.3V with 256° Phase When the SHDN pin is taken above 1.32V, its respective channel is allowed to operate. When the SHDN pin is driven below 1.32V, its channel is disabled. Taking SHDN1 below 0.6V will place the LT3692A in a low quiescent current mode. A graph of quiescent current vs SHDN1 voltage can be found in the Typical Performance Characteristics section. There is no hysteresis on the SHDN pins. Keep the connections from any series resistors to the SHDN pins short and make sure that the interplane or surface capacitance to switching nodes is minimized. 3692afc For more information www.linear.com/3692A 21 LT3692A Applications Information Soft-Start The output of the LT3692A regulates to the lowest voltage present at either the SS pin or an internal 0.806V reference. A capacitor from the SS pin to ground is charged by an internal 12µA current source resulting in a linear output ramp from 0V to the regulated output whose duration is given by: tRAMP C • 0.806V = SS 12µA At power-up, a reset signal sets the soft-start latch and discharges both SS pins to approximately 0V to ensure proper start-up. When both SS pins are fully discharged the latch is reset and the internal 12µA current source starts to charge the SS pin. When the SS pin voltage is below 115mV, the VC pin is pulled low which disables switching. This allows the SS pin to be used as an individual shutdown for each channel. As the SS pin voltage rises above 90mV, the VC pin is released and the output is regulated to the SS voltage. When the SS pin voltage exceeds the internal 0.806V reference, the output is regulated to the reference. The SS pin voltage will continue to rise until it is clamped at typically 2.15V. In the event of a VIN1 undervoltage lockout, the soft-start latch is set for both channels, triggering a full start-up sequence. If a channel’s SHDN pin is driven below 1.32V, its overvoltage lockout is enabled, or the internal die temperature for its power switch exceeds its maximum rating during normal operation, the soft-start latch is set for that channel. In addition, if the load exceeds the maximum output switch current, the output will start to drop causing the VC pin clamp to be activated. As long as the VC pin is clamped, the SS pin will be discharged. As a result, the output will be regulated to the highest voltage that the maximum output current can support. For example, if a 6V output is loaded by 1Ω the SS pin will drop to 0.64V, regulating the output at 4.8V (4.8A • 1Ω). Once the overload condition is removed, the output will soft start from the temporary voltage level to the normal regulation point. Since the SS pin is clamped at typically 2.15V and has to discharge to 0.806V before taking control of regulation, momentary overload conditions will be tolerated without 22 a soft-start recovery. The typical time before the SS pin takes control is: tSS(CONTROL) = CSS • 1.2V 1.4mA Open-Collector Comparators The CMPO pin is the open-collector output of an internal comparator. The comparator compares the CMPI pin voltage to 90% of the reference voltage (0.72V) with 60mV of hysteresis. The CMPO pin has a typical sink capability of 300µA when the CMPI pin is below the threshold and can withstand 40V when the threshold is exceeded. The CMPO pin is active (sink capability is reduced in shutdown and undervoltage lockout mode) as long as the VIN1 pin voltage exceeds typically 2.8V. The comparators can be used to monitor input and output voltages as well as die temperature. See the Typical Applications circuit collection for examples. Output Tracking/Sequencing Complex output tracking and sequencing between channels can be implemented using the LT3692A’s SS and CMPO pins. Figure 14 shows several configurations for output tracking/sequencing for a 3.3V and 1.8V application. Independent soft-start for each channel is shown in Figure 16a. The output ramp time for each channel is set by the soft-start capacitor as described in the soft-start section. Ratiometric tracking is achieved in Figure 14b by connecting both SS pins together. In this configuration, the SS pin source current is doubled (24µA) which must be taken into account when calculating the output rise time. By connecting a feedback network from VOUT1 to the SS2 pin with the same ratio that sets VOUT2 voltage, absolute tracking shown in Figure 14c is implemented. The minimum value of the top feedback resistor (R1) should be set such that the SS pin can be driven all the way to ground with 1.4mA of sink current when VOUT1 is at its regulated voltage. In addition, a small VOUT2 voltage offset will be present due to the SS2 12µA source current. This offset can be corrected for by slightly reducing the value of R2. For more information www.linear.com/3692A 3692afc LT3692A Applications Information Figure 14d illustrates output sequencing. When VOUT1 is within 10% of its regulated voltage, CMPO1 releases the SS2 soft-start pin allowing VOUT2 to soft-start. In this case CMPO1 will be pulled up to 2V by the SS pin. If a greater voltage is needed for CMPO1 logic, a pull-up resistor to VOUT1 can be used. This will decrease the soft-start ramp time and increase tolerance to momentary shorts. If precise output ramp up and down is required, drive the SS pins as shown in Figure 14e. The minimum value of resistor (R3) should be set such that the SS pin can be driven all the way to ground with 1.4mA of sink current during power-up and fault conditions. Application Optimization In multiple channel applications requiring large VIN to VOUT ratios, the maximum frequency and resulting inductor size is determined by the channel with the largest ratio. The LT3692A’s multi-frequency operation allows the user to minimize component size for each channel while maintaining constant frequency operation. The circuit in Figure 15 illustrates this approach. A 2-stage step-down approach coupled with multi-frequency operation will further reduce external component size by allowing an increase in frequency for the channel with the lower VIN to VOUT ratio. The drawback to this approach is that the output power capability for the first stage is determined by the output power drawn from the second stage. The dual step-down application in Figure 16 steps down the input voltage (VIN1) to the highest output voltage then uses that voltage to power the second output (VIN2). VOUT1 must be able to provide enough current for its output plus VOUT2 maximum load. Note that the VOUT1 voltage must be above VIN2’s minimum input voltage as specified in the Electrical Characteristics (typically 2.8V) when the second channel starts to switch. Delaying channel 2 can be accomplished by either independent soft-start capacitors or sequencing with the CMP01 output. For example, assume a maximum input of 36V: VIN = 36V, VOUT1 = 3.3V at 2A and VOUT2 = 1.2V at 1A. Frequency (Hz) = L= VOUT + VD 1 • VIN – VSW + VD tON(MIN) ( VIN – VOUT ) • VOUT VIN • f Single Step-Down: Frequency (Hz) = 1.2 + 0.6 1 • ≅ 350kHz 35V – 0.4 + 0.6 140ns L1= (36V – 3.3) • 3.3 ≥ 8.5µH L2 = (36V – 1.2) • 1.2 ≥ 3.3µH 36V • 350kHz 36V • 350kHz 2-Stage Step-Down: Frequency (Hz) = 3.3 + 0.6 1 • ≅ 750kHz 36V – 0.4 + 0.6 140ns L1= (36V – 3.3) • 3.3 ≥ 4.0µH L2 = (3.3 – 1.2) • 1.2 ≥ 1.0µH 36V • 750kHz 3.3 • 750kHz 2-Stage Step-Down Multi-Frequency: RDIV = 100k, FREQ1 = 550kHz, FREQ2 = 2200kHz. L1= (36V – 3.3) • 3.3 ≥ 5.4µH L2 = (3.3 – 1.2) • 1.2 ≥ 0.47µH 36V • 550kHz 3.3 • 2200K Hz In addition, RILIM2 = 33.2k reduces the peak current limit on channel 2 to 2A, which reduces inductor size and catch diode requirements. 3692afc For more information www.linear.com/3692A 23 LT3692A Applications Information Independent Start-Up Ratiometric Start-Up Absolute Start-Up VOUT1 0.5V/DIV VOUT1 0.5V/DIV PG1 VOUT2 0.5V/DIV VOUT2 0.5V/DIV 5ms/DIV LT3692A FB1 CMPI1 0.72V + – 0.1µF CMPO1 12µA 0.72V + – FB1 CMPI1 2.5V 12µA 0.72V SS1 2.5V PG2 12µA 0.72V SS2 12µA PG1 0.72V + – R4 FB2 CMPI2 2.5V PG2 12µA 0.72V SS2 R8 0.22µF (14a) PG1 VOUT2 R6 R5 CMPO2 R3 R2 CMPO1 + – 0.1µF R4 FB2 CMPI2 FB1 CMPI1 2.5V VOUT2 R5 CMPO2 R1 SS1 R6 VOUT1 R3 R2 CMPO1 + – 0.1µF FB2 CMPI2 SS2 R1 PG1 R4 LT3692A VOUT1 R3 R2 VOUT2 2.5V 10ms/DIV LT3692A R1 SS1 PG2 10ms/DIV VOUT1 2.5V VOUT2 0.5V/DIV PG2 PG2 12µA VOUT1 0.5V/DIV PG1 PG1 CMPO2 + – R6 R5 PG2 R7 (14b) (14c) Output Sequencing Controlled Power Up and Down VOUT1 0.5V/DIV VOUT1 0.5V/DIV PG1/PG2 VOUT2 0.5V/DIV VOUT2 0.5V/DIV PG1 SS1/2 PG2 10ms/DIV 10ms/DIV LT3692A LT3692A VOUT1 VOUT1 R1 FB1 CMPI1 2.5V 12µA 0.72V SS1 + – 0.1µF R1 R2 2.5V CMPO1 R4 12µA SS2 0.72V + – CMPO2 0.72V SS1 + – VOUT2 2.5V 12µA PG1 R5 FB2 CMPI2 FB1 CMPI1 + – R2 CMPO1 PG1 VOUT2 R4 R6 R5 FB2 CMPI2 2.5V PG2 R3 12µA SS2 0.72V + – 0.22µF R6 R5 CMPO2 PG2 3692a F14 (14d) (14e) Figure 14. SS Pin Configurations 24 3692afc For more information www.linear.com/3692A LT3692A Applications Information VIN1 5.5V TO 36V 4.7µF 4.7µF VIN2 VIN1 SHDN1 BST1 VOUT1 1.2V 3A 300kHz 4.7µH 0.47µF SW1 SW2 IND1 IND2 4.7µH 0.47µF VOUT2 3.3V 2A 600kHz 100k LT3692A VOUT2 VOUT1 100µF ×3 8.06k 100k SHDN2 BST2 100pF 4.02k FB1 PG1 CMPI2 CMPO1 CMPO2 SS1 DIV 33pF 49.9k ILIM2 VC2 RT/SYNC 820pF 7.50k 15.8k 47µF 8.06k PG2 SS2 ILIM1 VC1 0.1µF 24.9k FB2 CMPI1 CLKOUT TJ GND ILIM1 CLOCKOUT 600kHz 680pF 33pF 10nF 61.9k 0.1µF 13.0k 3692a F15 Figure 15. 3.3V and 1.2V Dual Step-Down Multi-Frequency Converter VIN1 5.5V TO 36V 4.7µF VIN2 VIN1 SHDN1 BST1 SHDN2 BST2 0.22µF VOUT1 3.3V 2.5A 550kHz 100k 47µF 4.7µH 24.9k IND1 IND2 LT3692A VOUT2 VOUT1 FB1 8.06k PG 33pF CMPI2 CMPO1 CMPO2 100k SS2 ILIM2 VC2 RT/SYNC 680pF 13k DIV 68.1k 102k 0.5µH 4.02k FB2 CMPI1 SS1 ILIM1 VC1 0.1µF 0.1µF SW2 SW1 CLKOUT GND TJ FB1 100pF VOUT2 1.2V 1A 47µF 2.2MHz 8.06k CLKOUT 2.2MHz 10nF 220pF 0.1µF 22pF 40.2k 33.2k 3692a F16 Figure 16. 3.3V and 1.2V 2-Stage Dual Step-Down Multi-Frequency Converter 3692afc For more information www.linear.com/3692A 25 LT3692A Applications Information Shorted and Reverse Input Protection If the inductor is chosen so that it won’t saturate excessively, an LT3692A step-down regulator will tolerate a shorted output. There is another situation to consider in systems where the output will be held high when the input to the LT3692A is absent. This may occur in battery charging applications or in battery back-up systems where a battery or some other supply is diode OR-ed with the LT3692A’s output. If the VIN1/2 pin is allowed to float and the SHDN pin is held high (either by a logic signal or because it is tied to VIN), then the LT3692A’s internal circuitry will pull its quiescent current through its SW pin. This is fine if your system can tolerate a few mA in this state. If you ground the SHDN pin, the SW pin current will drop to essentially zero. However, if the VIN pin is grounded while the output is held high, then parasitic diodes inside the LT3692A can pull large currents from the output through the SW pin and the VIN1/2 pin. Figure 17 shows a circuit that will run only when the input voltage is present and that protects against a shorted or reversed input. PARASITIC DIODE D4 VIN1/2 VIN SW VOUT1/2 LT3692A VIN LT3692A SW GND (18a) VIN LT3692A SW GND (18b) VIN LT3692A SW GND (18c) 3692a F18 Figure 18. Subtracting the Current When the Switch Is On (18a) from the Current When the Switch Is Off (18b) Reveals the Path of the High Frequency Switching Current (18c). Keep this Loop Small. The Voltage on the SW and BST Traces Will Also Be Switched; Keep These Traces as Short as Possible. Finally, Make Sure the Circuit Is Shielded with a Local Ground Plane 3692a F17 Figure 17. Diode D4 Prevents a Shorted Input from Discharging a Backup Battery Tied to the Output 26 3692afc For more information www.linear.com/3692A LT3692A Applications Information PCB Layout For proper operation and minimum EMI, care must be taken during printed circuit board (PCB) layout. Figure 18 shows the high di/dt paths in the buck regulator circuit. Note that large switched currents flow in the power switch, the catch diode and the input capacitor. The loop formed by these components should be as small as possible. These components, along with the inductor and output capacitor, should be placed on the same side of the circuit board and their connections should be made on that layer. Place a local, unbroken ground plane below these components, and tie this ground plane to system ground at one location, ideally at the ground terminal of the output capacitor C2. Route all small signal analog returns to the ground connection at the bottom of the package. Additionally, the SW and BST traces should be kept as short as possible. Thermal Considerations The PCB must also provide heat sinking to keep the LT3692A cool. The exposed metal on the bottom of the package must be soldered to a ground plane. This ground should be tied to other copper layers below with thermal vias; these layers will spread the heat dissipated by the LT3692A. DC1403A TSSOP LAYOUT Place additional vias near the catch diodes. Adding more copper to the top and bottom layers and tying this copper to the internal planes with vias can further reduce thermal resistance. The topside metal and component outlines in Figure 19 illustrate proper component placement and trace routing. The LT3692A’s powerful 3.8A switches allow the converter to source large output currents. Depending on the converter’s operating conditions, the resulting internal power dissipation can raise the junction temperature beyond its maximum rating. Operating conditions include input voltages, output voltages, switching frequencies, output currents, and the ambient environmental temperature, etc. An estimation of the junction temperature rise above ambient temperature helps determine whether a given design may exceed the maximum junction ratings for specific operating conditions. However, temperature rise depends on PCB design and the proximity to other heat sources. The final converter design must be evaluated on the bench. An estimation of the junction temperature rise begins by determining which circuit components dissipate power. In order to simplify the power loss estimation, only the inductors, catch diodes, and the LT3692A will be considered QFN LAYOUT Figure 19. PCB Top Layer and Component Placement for TSSOP and QFN Packages For more information www.linear.com/3692A 3692a F19 3692afc 27 LT3692A Applications Information as heat sources. After the operating conditions have been determined, the individual power losses are calculated by: V PowerD1,2 = 1− OUT •IOUT • VFD VIN PowerIND1,2 = RIND •IOUT2 V PowerCH1,2 = 0.1• OUT •IOUT2 + 2•10 –3 VIN •VIN + IOUT • VOUT • VBOOST 40• VIN + VIN IOUT VIN •IOUT •FSW •10−6 • + 0.3 3 where: FSW = Switching Frequency in kHz RIND = Inductor Resis tance VFD = Catch Diode Forward Voltage Drop VBOOST = Switch Boost Voltage Table 4. LT3692A Operating Conditions FSW VOUT1 IOUT1 VIN (V) (kHz) (V) (A) 30 300/600 1.2 2 12 1000 3.3 2.5 24 500 5 2 12 500 5 3 VOUT2 (V) 3.3 3.3 3.3 3.3 IOUT2 (A) 2 2.5 2 3 Table 5. LT3692A Power Loss Contributions PD1 PD2 PL1 PL2 (W) (W) (W) (W) 0.86 0.80 0.24 0.24 0.82 0.82 0.25 0.25 0.71 0.78 0.24 0.24 0.79 0.98 0.54 0.54 PCH1 (W) 0.38 0.62 0.54 0.81 PCH2 (W) 0.72 0.62 0.48 0.59 Table 6. Estimated System Power Loss and IC Temperature Rise TRISE TSSOP (°C) TRISE QFN (°C) PLOSS (W) CALCULATED MEASURED CALCULATED MEASURED CALCULATED MEASURED For the LT3692A demo board (see Figure 19) using the TSSOP package, the estimated junction temperature rise above ambient temperature is found by: TRISETSSOP ≈ 10 • (PowerD1 + PowerD2 ) + 12.3 • (PowerIND1 + Power IND2) + 17.5 • (PowerCH1 + PowerCH2 ) The estimated junction temperature rise above ambient for the LT3692A QFN layout (see Figure 19) is: TRISEQFN ≈ 8.5 • (Power D1+ Power D2) + 13 • (Power IND1+ Power IND2) + 23 • (PowerCH1 + PowerCH2 ) For example, the typical application circuits listed in Table 4 are used to calculate the individual power loss contributions in Table 5. Table 6 shows the estimated power loss and junction temperature rise above ambient temperature. 28 Note that the larger TSSOP package demonstrates better thermal performance than the compact QFN package on the LT3692A demo circuit boards. For LT3692A applications that favor thermal performance, the TSSOP package is the preferred package option. 3.2 3.4 3.0 4.2 3.2 3.5 3.1 4.7 41.9 44.3 38.5 55.4 44.9 48.8 35.3 52.0 45.8 49 42.2 61.2 49.1 54.8 42.3 63 The power loss and temperature rise equations provided in the Thermal Considerations section serve as a good starting point for estimating the junction temperature rise. However, the LT3692A is a very versatile converter. The combination of independent input voltages, output voltages, output currents, switching frequencies, and package selections for the LT3692A dictate that no power loss estimation scheme can accommodate every possible operating condition. As such, it is absolutely necessary to evaluate a converter’s performance at the bench. The power dissipation in the other power components such as boost diodes, input and output capacitors, inductor core loss, and trace resistances cause additional copper heating and can further increase what the IC sees as ambient temperature. See the LT1767 data sheet’s Thermal Considerations section. 3692afc For more information www.linear.com/3692A LT3692A Applications Information Die Temperature and Thermal Shutdown Generating a Negative Regulated Voltage The LT3692A TJ pin outputs a voltage proportional to the internal junction temperature. The TJ pin typically outputs 250mV for 25°C and has a slope of 10mV/°C. Without the aid of external circuitry, the TJ pin output is valid from 20°C to 150°C (200mV to 1.5V) with a maximum load of 100µA. The simple charge pump circuit in Figure 21 uses the CLKOUT pin output to generate a negative voltage, eliminating the need for an external regulated supply. Surface mount capacitors and dual-package Schottky diodes minimize the board area needed to implement the negative voltage supply. Full Temperature Range Measurement To extend the operating temperature range of the TJ output below 20°C, connect a resistor from the TJ pin to a negative supply as shown in Figure 20. The negative rail voltage and TJ pin resistor may be calculated using the following equations: VNEG 2 • TEMP(MIN)°C ≤ 100 R1≤ VNEG 33µA 330pF D4 CLKOUT GND 0.1µF D3 3692 F21 Figure 21. Circuit to Generate the Negative Voltage Rail to Extend the TJ Pin Operating Range TEMP(MIN)°C is the minimum temperature where a valid TJ pin output is required. VNEG = Regulated negative voltage supply. For example: TEMP(MIN)°C = –40°C VNEG ≤ –0.8V VNEG = –1, R1 ≤ |VNEG|/33µA = 30.2kΩ TJ LT3692A 30k D3, D4: ZETEX BAT54S where: LT3692A TJ As a safeguard, the LT3692A has an additional thermal shutdown threshold set at a typical value of 163°C for each channel. Each time the threshold is exceeded, a power-on sequence for that channel will be initiated. The sequence will then repeat until the thermal overload is removed. It should be noted that the TJ pin voltage represents a steady-state temperature and should not be used to guarantee that maximum junction temperatures are not exceeded. Instantaneous power along with thermal gradients and time constants may cause portions of the die to exceed maximum ratings and thermal shutdown thresholds. Be sure to calculate die temperature rise for steady state (>1Min) as well as impulse conditions. R1 VNEG GND + 3692 F20 Figure 20. Circuit to Extend the TJ Pin Operating Range 3692afc For more information www.linear.com/3692A 29 LT3692A Applications Information CLKOUT Capacitive Loading A minor drawback to generating a negative rail from the CLKOUT pin is that the charge pump adds capacitance to the CLKOUT pin, resulting in an output synchronization clock signal phase delay. Figures 22 and 23 show the impact of capacitive loading on the CLKOUT signal rise and fall times. Note that a typical 10:1 150MHz oscilloscope probe contributes significant capacitance to the CLKOUT node, necessitating a low capacitance probe for accurate measurements. Applications requiring CLKOUT to generate the negative supply voltage and provide the synchronization clock to other regulators may benefit from buffering CLKOUT prior to the charge pump circuitry. CHARGE PUMP SCOPE PROBE: 15pF SYNCHRONIZED LT3692A RT/SYNC PIN FET PROBE: 2pF 500mV/DIV 40ns/DIV FREQUENCY: 1.000MHz 3692a F22 Figure 22. CLKOUT Rise Time Other Linear Technology Publications Application Notes 19, 35 and 44 contain more detailed descriptions and design information for buck regulators and other switching regulators. The LT1376 data sheet has a more extensive discussion of output ripple, loop compensation and stability testing. Design Note 100 shows how to generate a dual (+ and –) output supply using a buck regulator. SCOPE PROBE: 15pF CHARGE PUMP SYNCHRONIZED LT3692A RT/SYNC PIN 500mV/DIV FET PROBE: 2pF 20ns/DIV FREQUENCY: 1.000MHz 3692a F23 Figure 23. CLKOUT Fall Time 30 3692afc For more information www.linear.com/3692A VIN 6V TO 36V For more information www.linear.com/3692A 0.1µF VOUT1 5V 1.5A 500kHz 100k 47µF 4.7µF 33pF 8.06k 680pF 10.0k 100pF 0.47µF 61.9k 42.2k 6.8µH VIN2 IND2 SW2 SHDN2 BST2 102k DIV GND TJ CLKOUT ILIM1 VC1 RT/SYNC SS2 ILIM2 VC2 SS1 CMPO2 CMPO1 FB2 CMPI2 CMPI1 FB1 LT3692A VOUT2 VOUT1 IND1 SW1 SHDN1 BST1 VIN1 10nF 16.9k 1.5µH 33pF 330pF 11.0k 8.06k 100pF 0.1µF 49.9k PG 100k 8.06k 10k CLOCKOUT 2MHz 22µF VOUT2 2.5V 1A 2MHz 8.06k 4.02k VOUT3 1.2V 1A 1MHz 49.9k 33pF 8.06k 100µF 0.1µF 4.02k 9.76k 470pF 100pF 1.5µH 1µF VIN2 IND2 SW2 SHDN2 BST2 61.9k DIV FB2 ILIM2 VC2 SS2 CMPO2 CMPI2 TJ CLKOUT GND RT/SYNC ILIM1 VC1 SS1 CMPO1 CMPI1 FB1 LT3692A VOUT2 VOUT1 IND1 SW1 SHDN1 BST1 VIN1 Quad Output 5V, 2.5V, 1.8V and 1.2V Multi-Frequency Synchronized, 2-Stage Converter with Output Sequencing, Absolute Tracking and Current Limiting 10nF 10k 1.5µH 15.0k 220pF 100pF 0.1µF 8.06k 33pF 1µF 3692a TA02 49.9k VOUT4 1.8V 1A 47µF 2MHz LT3692A Typical Applications 3692afc 31 LT3692A TYPICAL APPLICATIONS 3.3V and 1.8V 2-Stage Dual Step-Down Multi-Frequency Converter VIN 5.5V TO 36V 4.7µF VIN2 VIN1 SHDN1 BST1 8.2µH 0.47µF VOUT1 3.3V 2.5A 400kHz 100µF SHDN2 BST2 SW1 SW2 IND1 IND2 100pF 24.9k FB1 FB2 CMPI1 CMPI2 CMPO1 CMPO2 SS1 DIV 33pF 16.5k ILIM2 VC2 RT/SYNC 470pF 47.5k 102k 10k 47µF 100pF 100k VOUT2 1.8V 1A 1600kHz 8.06k PG SS2 ILIM1 VC1 100k 0.22µF LT3692A VOUT2 VOUT1 8.06k 0.1µF 1µH CLKOUT GND TJ 0.1µF CLOCKOUT 1600kHz 330pF 33pF 10nF 36.5k 40.2k 3692a TA03 32 3692afc For more information www.linear.com/3692A LT3692A TYPICAL APPLICATIONS 12V to 3.3V and 2.5V Converter with Start-Up Current Limiting VIN 12V 4.7µF 4.7µF VIN2 VIN1 SHDN1 BST1 2.2µH 0.22µF VOUT1 2.5V 3A 1MHz SHDN2 BST2 SW1 SW2 IND1 IND2 0.22µF LT3692A VOUT2 VOUT1 47µF 8.06k 100pF 16.9k FB1 FB2 CMPI1 CMPI2 CMPO1 CMPO2 ILIM2 VC2 ILIM1 VC1 0.1µF RT/SYNC 330pF DIV 33pF 0.1µF 21.0k 28.0k 24.9k 100pF 8.06k 47µF VOUT2 3.3V 3A 1MHz SS2 SS1 120k 2.2µH CLKOUT GND TJ CLOCKOUT 1MHz 33pF 0.1µF 330pF 10nF 24.9k 0.1µF 120k 3692a TA04 3692afc For more information www.linear.com/3692A 33 LT3692A TYPICAL APPLICATIONS 3.3V/5A Single Output with UVLO/OVLO and Power Good VIN 5.5V TO 18V 60V TRANSIENT 4.7µF ×2 13k 174k 7.15k 37.4k SHDN2 BST1 CMPI2 CMPO2 51.1k ILIM1 ILIM2 820pF 33pF SW1 CLOCKOUT 1MHz SS1 VOUT2 SS2 VC1 BST2 SW2 CLKOUT 10nF 20k 28k DIV 47µF ×2 GND FB1 CMPI1 FB2 VOUT 3.3V 5A 2MHz EFFECTIVE RIPPLE 0.22µF 3.3µH IND2 RT/SYNC TJ 0.1µF 0.22µF 3.3µH IND1 LT3692A VOUT1 VC2 Q1 2N3904 34 VIN2 VIN1 SHDN1 24.9k 8.06k CMPO1 100k PG 3692a TA05 3692afc For more information www.linear.com/3692A LT3692A TYPICAL APPLICATIONS Power Supply Dual Input Single 3.3V/4A Output Step-Down Converter VIN1 12V 4.7µF 47.5k 13k 2.2µF VIN2 VIN1 SHDN1 SHDN1 SHDN2 BST1 CMPO1 CMPO2 SW1 VIN2 5V 2A MAX 0.22µF 2.2µH IND1 LT3692A SS2 VOUT1 SS1 0.1µF 64.9k 36.5k 33pF 680pF 21.0k CLOCKOUT 2MHz 61.9k 61.9k ILIM1 VOUT2 ILIM2 VC1 BST2 SW2 VC2 0.22µF 2.2µH IND2 CLKOUT RT/SYNC DIV FB1 CMPI1 FB2 TJ CMPI2 10nF 47µF ×2 GND VOUT 3.3V 4A 24.9k 8.06k 3692a TA06 3692afc For more information www.linear.com/3692A 35 LT3692A TYPICAL APPLICATIONS 5V and 1.8V Dual 2-Stage Converter VIN1 6V TO 36V 4.7µF VIN2 VIN1 SHDN1 BST1 4.7µH 0.22µF VOUT1 5V 1A 1MHz SHDN2 BST2 SW1 SW2 IND1 IND2 1µH 0.22µF LT3692A VOUT2 VOUT1 22µF 100k 42.2k 8.06k PG FB1 CMPI2 CMPO1 CMPO2 SS1 0.1µF 49.9k 10k ILIM2 VC2 RT/SYNC DIV 33pF 61.9k 61.9k FB1 47µF 100pF 8.06k SS2 ILIM1 VC1 680pF 10k FB2 CMPI1 VOUT2 1.8V 1A 2MHz CLKOUT GND TJ ILIM1 CLOCKOUT 2MHz 33pF 0.1µF 330pF 10nF 39.2k 3692a TA07 36 3692afc For more information www.linear.com/3692A 100k 0.1µF PG1 VOUT1 12V 0.5A 1MHz 37.6k 33pF 470pF 8.06k 22µF 0.47µF VIN 15V TO 36V 28k 113k 1k 10µH OFF ON 4.7µF IND2 SW2 SHDN2 BST2 VIN2 FB2 DIV GND TJ CLKOUT ILIM2 VC2 ILIM1 VC1 RT/SYNC SS2 CMPO2 CMPI2 SS1 CMPO1 CMPI1 FB1 LT3692A VOUT2 VOUT1 IND1 SW1 SHDN1 BST1 VIN1 24.9k 10nF FB1 3.3µH SHDN1 33pF 16.0k 330pF 8.06k 0.22µF 100k 47µF For more information www.linear.com/3692A 133k 0.1µF 0.1µF SS2 VOUT3 1.2V 3A 1MHz OUT2 MOD GND SET OUT1 U1 LTC6908-1 V+ VOUT2 3.3V 2A 1MHz VOUT2 100k 8.06k 100µF 0.22µF 33pF 150pF 4.99k 1nF SS2 4.02k 1.5µH SHDN1 1µF IND2 SW2 SHDN2 BST2 VIN2 GND TJ CLKOUT DIV RT/SYNC FB2 CMPI2 CMPO2 SS2 ILIM2 VC2 CMPI1 CMPO1 SS1 ILIM1 VC1 FB1 LT3692A VOUT2 VOUT1 IND1 SW1 SHDN1 BST1 VIN1 12V, 3.3V, 2.5V, 1.2V Quad Output with External Synchronization, Output Sequencing and Tracking Application 10nF SS2 16.9k 2.2µH SHDN1 33pF 8.06k VOUT2 3692a TA08 100k 47µF VOUT4 2.5V 3A 1MHz 330pF 11.2k 100pF 0.22µF 1µF LT3692A TYPICAL APPLICATIONS 37 3692afc LT3692A TYPICAL APPLICATIONS 5V, 3.3V, 2.5V, 1.8V Synchronized Quad Output VOUT1 5V 1A 2.2µF SVIN PVIN2 PVIN DDR 4.7µF ×2 RUN LT3612 MODE RT VIN2 VIN1 SHDN1 BST1 6.8µH 0.22µF 100pF 42.2k 8.06k SW1 SW2 IND1 IND2 FB1 FB2 CMPI1 CMPI2 CMPO1 SS1 CMPO2 SS2 ILIM2 VC2 ILIM1 VC1 0.1µF RT/SYNC 330pF DIV 33pF 60.4k 24.9k 16k 270k FB VOUT2 3.3V 100µF 2A ITH TRACK/SS SGND PGND SVIN PVIN2 60.4k SHDN2 BST2 6.8µH 2.2µF 0.22µF LT3692A VOUT2 VOUT1 47µF 3.3µH SW PGOOD VIN1 7V TO 36V TJ 0.1µF RUN LT3612 100k ILIM1 VC1 MODE 100°C TEMP FLAG SS1 RT 3.3µH SW PGOOD 47µF FB1 CLKOUT GND PVIN DDR 191k FB VOUT3 2.5V 100µF 2A ITH TRACK/SS SGND PGND SVIN PVIN2 60.4k CLOCKOUT 600kHz 2.2µF 28k 73.2k R14 49.9k PVIN DDR PGOOD RUN LT3612 MODE RT SGND 3.3µH SW 121k FB VOUT4 1.8V 100µF 2A ITH TRACK/SS 60.4k PGND 0.1µF 3692 TA09 38 3692afc For more information www.linear.com/3692A LT3692A Package Description Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. FE Package 38-Lead Plastic TSSOP (4.4mm) (Reference LTC DWG # 05-08-1772 Rev C) Exposed Pad Variation AA 4.75 REF 38 9.60 – 9.80* (.378 – .386) 4.75 REF (.187) 20 6.60 ±0.10 4.50 REF 2.74 REF SEE NOTE 4 6.40 2.74 REF (.252) (.108) BSC 0.315 ±0.05 1.05 ±0.10 0.50 BSC RECOMMENDED SOLDER PAD LAYOUT 4.30 – 4.50* (.169 – .177) 0.09 – 0.20 (.0035 – .0079) 0.50 – 0.75 (.020 – .030) NOTE: 1. CONTROLLING DIMENSION: MILLIMETERS 2. DIMENSIONS ARE IN MILLIMETERS (INCHES) 3. DRAWING NOT TO SCALE 1 0.25 REF 19 1.20 (.047) MAX 0° – 8° 0.50 (.0196) BSC 0.17 – 0.27 (.0067 – .0106) TYP 0.05 – 0.15 (.002 – .006) FE38 (AA) TSSOP REV C 0910 4. RECOMMENDED MINIMUM PCB METAL SIZE FOR EXPOSED PAD ATTACHMENT *DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.150mm (.006") PER SIDE 3692afc For more information www.linear.com/3692A 39 LT3692A Package Description Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. UH Package 32-Lead Plastic QFN (5mm × 5mm) (Reference LTC DWG # 05-08-1693 Rev D) 0.70 ±0.05 5.50 ±0.05 4.10 ±0.05 3.50 REF (4 SIDES) 3.45 ± 0.05 3.45 ± 0.05 PACKAGE OUTLINE 0.25 ± 0.05 0.50 BSC RECOMMENDED SOLDER PAD LAYOUT APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 5.00 ± 0.10 (4 SIDES) BOTTOM VIEW—EXPOSED PAD 0.75 ± 0.05 R = 0.05 TYP 0.00 – 0.05 R = 0.115 TYP PIN 1 NOTCH R = 0.30 TYP OR 0.35 × 45° CHAMFER 31 32 0.40 ± 0.10 PIN 1 TOP MARK (NOTE 6) 1 2 3.50 REF (4-SIDES) 3.45 ± 0.10 3.45 ± 0.10 (UH32) QFN 0406 REV D 0.200 REF NOTE: 1. DRAWING PROPOSED TO BE A JEDEC PACKAGE OUTLINE M0-220 VARIATION WHHD-(X) (TO BE APPROVED) 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 40 0.25 ± 0.05 0.50 BSC 3692afc For more information www.linear.com/3692A LT3692A Revision History REV DATE DESCRIPTION PAGE NUMBER A 9/11 Added H-grade 2 to 4 B 4/12 Clarified the synchronization maximum frequency and Typical Application. 1 Clarified the Electrical Characteristics table. 4 Clarified the DIV Voltage Threshold vs Temperature graph. 7 Replaced 90mV with 100mV. 12 Clarified Table 1. 13 Replaced DIV resistor values in the applications schematics. C 3/13 25, 31, 32 Added VIN1 Quiescent Current vs SHDN1 Voltage Graph 6 Clarified SHDN1/2 Pin Function Description 10 Clarified SHDN pin operation in Applications Information operation in general description 11 Clarified SHDN pin operation description in Applications Information 21 3692afc Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection its circuits as described herein will not infringe on existing patent rights. Forofmore information www.linear.com/3692A 41 LT3692A Typical Application FMEA Fault Tolerant 3.3V/2A and 5V/2A Dual Converter VIN1 6V TO 36V (60V TRANSIENT) 4.7µF SHDN2 6.8µH 0.22µF VOUT1 5V 2A 500kHz VIN1 SHDN1 BST1 4.7µF 100k VIN2 SHDN2 BST2 SW1 SW2 IND1 IND2 5.6µH 0.22µF VOUT2 3.3V 2A 500kHz LT3692A VOUT2 VOUT1 4.22k 47µF 249k 806Ω PG1 SS2 ILIM2 FB1 CMPI2 CMPO1 CMPO2 SS1 820pF 12.7k 10nF ILIM1 VC1 DIV 100µF 806Ω 249k PG2 SS2 ILIM2 VC2 RT/SYNC 33pF 2.49k FB2 CMPI1 CLKOUT GND TJ CLOCKOUT 500kHz 13.0k 10nF 680pF 15.4k 33pF 22nF 49.9k 3692a TA10 Related Parts PART NUMBER DESCRIPTION LT3692 36V with Transient Protection to 60V, Dual 3.5A, 2.5MHz, High Efficiency VIN = 3V to 36V, Transients to 60V, VOUT(MIN) = 0.8V, IQ = 4mA, ISD <10µA, 5mm × 5mm QFN-32 Step-Down DC/DC Converter LT3507 36V, Triple 2.4A, 1.4A and 1.4A (IOUT), 2.5MHz, High Efficiency Step-Down DC/DC Converter with LDO Controller VIN = 4V to 36V, VOUT(MIN) = 0.8V, IQ = 7mA, ISD = 1µA, 5mm × 7mm QFN-38 LT3508 36V with Transient Protection to 40V, Dual 1.4A (IOUT), 3MHz, High Efficiency Step-Down DC/DC Converter VIN = 3.7V to 37V, VOUT(MIN) = 0.8V, IQ = 4.6mA, ISD = 1µA, 4mm × 4mm QFN-24, TSSOP-16E LT3680 36V, 3A, 2.4MHz High Efficiency Micropower Step-Down DC/DC Converter VIN = 3.6V to 36V, VOUT(MIN) = 0.8V, IQ = 75µA, ISD < 1µA, 3mm × 3mm DFN-10, MSOP-10E LT3693 36V, 3A, 2.4MHz High Efficiency Step-Down DC/DC Converter VIN = 3.6V to 36V, VOUT(MIN) = 0.8V, IQ = 1.3mA, ISD < 1µA, 3mm × 3mm DFN-10, MSOP-10E LT3480 36V with Transient Protection to 60V, 2A (IOUT), 2.4MHz, High Efficiency Step-Down DC/DC Converter with Burst Mode® Operation VIN = 3.6V to 38V, Transients to 60V, VOUT(MIN) = 0.78V, IQ = 70µA, ISD < 1µA, 3mm × 3mm DFN-10, MSOP-10E LT3980 58V with Transient Protection to 80V, 2A (IOUT), 2.4MHz, High Efficiency Step-Down DC/DC Converter with Burst Mode Operation VIN = 3.6V to 58V, Transients to 80V, VOUT(MIN) = 0.79V, IQ = 75µA, ISD < 1µA, 3mm × 4mm DFN-16, MSOP-16E LT3971 38V, 1.2A (IOUT), 2MHz, High Efficiency Step-Down DC/DC Converter with Only 2.8µA of Quiescent Current VIN = 4.2V to 38V, VOUT(MIN) = 1.2V, IQ = 2.8µA, ISD < 1µA, 3mm × 3mm DFN-10, MSOP-10E LT3991 55V, 1.2A (IOUT), 2MHz, High Efficiency Step-Down DC/DC Converter with Only 2.8µA of Quiescent Current VIN = 4.2V to 55V, VOUT(MIN) = 1.2V, IQ = 2.8µA, ISD < 1µA, 3mm × 3mm DFN-10, MSOP-10E 42 Linear Technology Corporation COMMENTS 1630 McCarthy Blvd., Milpitas, CA 95035-7417 For more information www.linear.com/3692A (408)432-1900● FAX:(408)434-0507● www.linear.com/3692A 3692afc LT 0313 REV C • PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 2011