NJU7045 Input/Output Full-Swing High Output Current Single C-MOS Operational Amplifier with Shutdown ■PACKAGE OUTLINE ■GENERAL DESCRIPTION The NJU7045 is a C-MOS operational amplifier permitting a full-swing input and output in full-swing under high load. Based on C-MOS technology, there are excellent features such as high output current, low current consumption, low operating voltage, and very high input impedance. ■ FEATURES ●Operating Voltage: ●Input/Output Full-Swing ●High Output Current: ●Input Offset Voltage: ●Wide Input Common Mode ●Operating Current: (Active) (Shutdown) ●High Input Impedance: ●Low Input Bias Current: ●Ground Sensing ●Tiny Package: NJU7045RB1 NJU7045F1 2.2V to 5.5V 40mA at VO=0V VIO=10mV max. Voltage Range:VSS to VDD IDD=350µA typ. (at VDD=3V) IDD=0.9µA typ. (at VDD=2.2V to 5.5V) 1TΩ Typ. IIB=1pA typ. TVSP8, MTP6 ■ PIN CONFIGURATION 1 8 + 2 7 3 6 4 5 NJU7045RB1 (Top View) Ver.2004-08-24 PIN FUNCTION 1. NC 2. –INPUT 3. +INPUT 4. VSS 5. NC 6. OUTPUT 7. VDD 8. SHDN 1 2 6 + − 3 5 4 NJU7045F1 (Top View) PIN FUNCTION 1. OUTPUT 2. VSS 3. +INPUT 4. –INPUT 5. SHDN 6. VDD -1- NJU7045 ■ ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL Supply Voltage Common Mode Input Voltage Range Differential Input Voltage Range VDD VICM VID Power Dissipation PD Output Current Operating Temperature Range Storage Temperature Range IO Topr Tstg RATINGS UNIT 7 0 to 7 (Note 1) ±7 320 [TVSP8] 410 [TVSP8] (Note 2) 540 [TVSP8] (Note 3) 200 [ MTP6 ] 410 [ MTP6 ] (Note 2) 580 [ MTP6 ] (Note 3) ±75 [TVSP8, MTP6] -40 to +85 -55 to +125 V V V mW mA ˚C ˚C (Note 1) For supply voltage less than 7V, the absolute maximum input voltage is equal to the supply voltage. (Note 2) On the PCB " EIA/JEDEC (76.2x11.43x1.6mm, two layers, FR-4) " (Note 3) On the PCB " EIA/JEDEC (76.2x11.43x1.6mm, four layers, FR-4) " FIGURE 1-1. Power Dissipation vs. Ambient Temperature (3) 500 400 300 600 Power Dissipation P D (mW) Power Dissipation P D (mW) 600 Package Type (1)TVSP8 : ∆PD= -3.2(mW/°C) (2)TVSP8[Tw o Layer] : ∆PD= -4.1(mW/°C) (3)TVSP8[Four Layer] : ∆PD= -5.4(mW/°C) FIGURE 1-2. Power Dissipation vs. Ambient Temperature (2) (1) 200 100 (3) 500 400 Package Type (1)MTP6 : ∆PD= -2(mW/°C) (2)MTP6[Tw o Layer] : ∆PD= -4.1(mW/°C) (3)MTP6[Four Layer] : ∆PD= -5.8(mW/°C) (2) 300 200 (1) 100 0 25 50 75 Ambient Temperature Ta (°C) 100 0 25 50 75 100 Ambient Temperature Ta (°C) (Note 4) Please do not exceed "Power Dissipation (PD)" the power dissipation in IC is absolutely indicated to be in the maximum rating. See the figure "Power Dissipation vs. Ambient Temperature" for information on temperature derating of this device. -2- Ver.2004-08-24 NJU7045 ■ OPERATING VOLTAGE (Ta=25˚C) PARAMETER SYMBOL RATINGS UNIT Supply Voltage V DD 2.2 to 5.5 V ■STATE DEFINITION OF NJU7045 OPERATION ●”State of NJU7045 Operation” vs. “Turn-on/off Control Voltage VSD“ State Definition CONTROL CONDITION Amplifier Operating V SD =V I H Shutdown V SD =V I L (2.2V ≤ VDD ≤ 5.5V, Ta=25˚C) State of NU7045 Operation Amplifier is active. The output impedance is high, output signal is muted and the supply current is reduced. ■ELECTRICAL CHARACTERISTICS [Enable/Shutdown Control Information] ●Turn-on/off Control Voltage Range for SHDN Pin PARAMETER SYMBOL Turn-on Voltage to Enable part Turn-off Voltage VIH VIL TEST CONDITION (Note 5) (Note 5) (2.2V ≤ VDD ≤ 5.5V, Ta=25˚C) MIN. TYP. MAX. UNIT V DD x 0.7 0 - V DD V DD x 0.3 V V (Note 5) The SHDN pin can’t be left unconnected. ●DC CHARACTERISTICS of “SHDN Pin” PARAMETER SYMBOL Input Bias Current of SHDN Pin I BSD (2.2V ≤ VDD ≤ 5.5V, Ta=25˚C) TEST CONDITION 0 ≤ VSD ≤ VDD MIN. TYP. MAX. UNIT - - ±2 µA ●Turn-on/off Time (2.2V ≤ VDD ≤ 5.5V, Ta=25˚C) PARAMETER SYMBOL Amplifier Turn-off Time TOFF Amplifier Turn-on Time TON TEST CONDITION TVSDHL ≤ 100ns FIGURE 2,3 TVSDLH ≤ 100ns FIGURE 2,3 FIGURE 2. TOFF/TON CONDITION TVSDHL MIN. TYP. MAX. UNIT - 1 - µs - 10 - µs FIGURE 3. TOFF/TON TEST CIRCUIT TVSDLH VDD [ RL=600Ω , C L=0pF ] VDD 70% V SD 0.1V VDD 30% VDD 90% RL CL VSD V OUT VDD 10% TOFF Ver.2004-08-24 TON -3- NJU7045 ■ELECTRICAL CHARACTERISTICS [Shutdown Characteristics] ●DC CHARACTERISTICS PARAMETER SYMBOL Output Leak Current Operating Current I L EAK I DDSD (2.2V ≤ VDD ≤ 5.5V, Ta=25˚C) TEST CONDITION MIN. TYP. MAX. UNIT - - ±3 0.9 µA µA FIGURE 4 No Signal Apply, No Load, V SD ≤ 0.2V ●AC CHARACTERISTICS (2.2V ≤ VDD ≤ 5.5V, Ta=25˚C) PARAMETER SYMBOL Mute Level MUTE TEST CONDITION MIN. TYP. MAX. UNIT - -100 - dB VIN=1VPP, f=1kHz, FIGURE 5 FIGURE 4. LEAK CURRENT TEST CIRCUIT Vout Measurement Point VDD [ RL=100kΩ ] RL 1/2 VDD ILEAK = VOUT - 1/2VDD RL 1/2 VDD VSD=VIL FIGURE 5. MUTE LEVEL TEST CIRCUIT Vin Measurement Point VDD Vout Measurement Point [ RL=600Ω ] RL MUTE LEVEL=VOUT / VIN 1/2 VDD 1/2 VDD VSD=VIL -4- Ver.2004-08-24 NJU7045 ■ELECTRICAL CHARACTERISTICS [Amplifier Operating] ●DC CHARACTERISTICS (VDD=5V, 3.5V ≤ V SD ≤ 5V, Ta=25˚C) PARAMETER SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT Operating Current Input Offset Voltage Input Bias Current Input Offset Current Large Signal Voltage Gain I DD VIO IB IIO AV No signal Apply, V SD =V DD 70 450 1 1 90 700 10 - µA mV pA pA dB Common Mode Rejection Ratio CMR 44 60 - dB Supply Voltage Rejection Ratio SVR CMR+: 2.5V ≤ V CM ≤ 5V CMR-: 0V ≤ V CM ≤ 2.5V (Note 6) 4.0V ≤ V DD ≤ 5.5V, V CM =V DD /2, V SD =V DD 55 85 - dB Output Voltage1 VOH1 VOL1 R L =10kΩ to 2.5V R L =10kΩ to 2.5V 4.95 - - 0.05 V V Output Voltage2 VOH2 VOL2 R L =600Ω to 2.5V R L =600Ω to 2.5V 4.9 - - 0.10 V V Output Source Current Output Sink Current Input Common Mode Voltage Range I SOURCE I SI NK VICM V O =2.5V V O =2.5V CMR ≥ 44dB 70 70 0 - 5 mA mA V R L =10kΩ to 2.5V, Vo=2.5V±2.4V (Note 6) CMR is represented by either CMR+ or CMR- has lower value. ●AC CHARACTERISTICS (VDD=5V, 3.5V ≤ V SD ≤ 5V, Ta=25˚C) PARAMETER SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT Unity Gain Bandwidth Total Harmonic Distortion Equivalent Input Noise Voltage GB THD V NI R L =10kΩ to 2.5V f=1kHz, VIN=1Vpp, AV=0dB f=1kHz - 0.8 0.05 40 - MHz % nV/√Hz ●TRANSIENT CHARACTERISTICS (VDD=5V, 3.5V ≤ V SD ≤ 5V, Ta=25˚C) PARAMETER SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT Slew Rate SR R L =10kΩ to 2.5V - 0.8 - V/µs Ver.2004-08-24 -5- NJU7045 ■ELECTRICAL CHARACTERISTICS [Amplifier Operating] ●DC CHARACTERISTICS (VDD=3V, 2.1V ≤ V SD ≤ 3V, Ta=25˚C) PARAMETER SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT Operating Current Input Offset Voltage Input Bias Current Input Offset Current Large Signal Voltage Gain I DD VIO IB IIO AV No signal Apply, V SD =V DD 70 350 1 1 90 600 10 - µA mV pA pA dB Common Mode Rejection Ratio CMR CMR+: 1.5V ≤ V CM ≤ 3V CMR-: 0V ≤ V CM ≤ 1.5V (Note 7) 42 60 - dB Supply Voltage Rejection Ratio SVR 2.7V ≤ V DD ≤ 4.0V, V CM =V DD /2, V SD =V DD 50 80 - dB Output Voltage1 VOH1 VOL1 R L =10kΩ to 1.5V R L =10kΩ to 1.5V 2.95 - - 0.05 V V Output Voltage2 VOH2 VOL2 R L =600Ω to 1.5V R L =600Ω to 1.5V 2.9 - - 0.10 V V Output Source Current Output Sink Current Input Common Mode Voltage Range I SOURCE I SI NK VICM V O =1.5V V O =1.5V CMR ≥ 42dB 30 30 0 40 40 - 3 mA mA V R L =10kΩ to 1.5V, Vo=1.5V±1.4V (Note 6) CMR is represented by either CMR+ or CMR- has lower value. ●AC CHARACTERISTICS (VDD=3V, 2.1V ≤ V SD ≤ 3V, Ta=25˚C) PARAMETER SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT Unity Gain Bandwidth Total Harmonic Distortion Equivalent Input Noise Voltage GB THD V NI R L =10kΩ to 1.5V f=1kHz, VIN=1Vpp, AV=0dB f=1kHz - 0.8 0.05 40 - MHz % nV/√Hz ●TRANSIENT CHARACTERISTICS -6- (VDD=3V, 2.1V ≤ V SD ≤ 3V, Ta=25˚C) PARAMETER SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT Slew Rate SR R L =10kΩ to 1.5V - 0.7 - V/µs Ver.2004-08-24 NJU7045 ■ELECTRICAL CHARACTERISTICS [Amplifier Operating] ●DC CHARACTERISTICS (VDD=2.2V, 1.54V ≤ V SD ≤ 2.2V, Ta=25˚C) PARAMETER SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT Operating Current Input Offset Voltage Input Bias Current Input Offset Current Large Signal Voltage Gain I DD VIO IB IIO AV No Signal Apply, V SD =V DD 70 300 1 1 90 500 10 - µA mV pA pA dB Common Mode Rejection Ratio CMR CMR+: 1.1V ≤ V CM ≤ 2.2V CMR-: 0V ≤ V CM ≤ 1.1V (Note 7) 30 60 - dB Supply Voltage Rejection Ratio SVR 2.2V ≤ V DD ≤ 2.7V, V CM =V DD /2, V SD =V DD 45 70 - dB Output Voltage1 VOH1 VOL1 R L =10kΩ to 1.1V R L =10kΩ to 1.1V 2.15 - - 0.05 V V Output Voltage2 VOH2 VOL2 R L =600Ω to 1.1V R L =600Ω to 1.1V 2.1 - - 0.1 V V Output Source Current Output Sink Current Input Common Mode Voltage Range I SOURCE I SI NK VICM V O =1.1V V O =1.1V CMR ≥ 30dB 10 10 0 15 15 - 2.2 mA mA V R L =10kΩ to 1.1V, Vo=1.1V±1.0V (Note 7) CMR is represented by either CMR+ or CMR- has lower value. ●AC CHARACTERISTICS (VDD=2.2V, 1.54V ≤ V SD ≤ 2.2V, Ta=25˚C) PARAMETER SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT Unity Gain Bandwidth Total Harmonic Distortion Equivalent Input Noise Voltage GB THD V NI R L =10kΩ to 1.1V f=1kHz, VIN=1Vpp, AV=0dB f=1kHz - 0.8 0.05 40 - MHz % nV/√Hz ●TRANSIENT CHARACTERISTICS (VDD=2.2V, 1.54V ≤ V SD ≤ 2.2V, Ta=25˚C) PARAMETER SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT Slew Rate SR R L =10kΩ to 1.1V - 0.6 - V/µs [CAUTION] The specifications on this data book are only given for information, without any guarantee as regards either mistakes or omissions. The application circuits in this data book are described only to show representative usages of the product and not intended for the guarantee or permission of any right including the industrial rights. Ver.2004-08-24 -7-