Power-One DFC25E24T5/12 Triple output Datasheet

DFC25 SERIES
TRIPLE OUTPUT
FEATURES
• Up to 25 Watts with Triple Outputs
• +3.3V or +5V Main Outputs
• Remote ON/OFF
• Common and Differential Mode Input Filters
• Main Output Trim
• Efficiencies to 81%
• Operation from -25°C up to 85°C
• 700/1544V Isolation
• Two Year Warranty
• UL/CSA/TÜV
DESCRIPTION
The DFC25 Series DC/DC converter provides three output voltages
from a single 12, 24, or 48 volt nominal input for industrial and
datacom equipment. Available output power ranges up to 25 watts.
Excellent noise performance is attained via an aluminum case,
toroidal magnetics, and double shielded transformers. Common
mode and differential mode input filtering are integral to the design.
Selected models provide 1544 volts isolation from input to output.
The input and output sections of the DFC25 Series are protected
from overvoltage transients via internal circuitry. Same voltage
single output units of the DFC25 family may be connected in
parallel to achieve additional output current.
BOTTOM VIEW
Selection Chart - Up to 25 Watts Output Power
Input Range
VDC
Min
Max
Model
DFC25E24T5/12
DFC25E24T5/15
DFC25E48T3.3/12
DFC25E48T5/12
18
18
36
36
36
36
72
72
Output
VDC
Nominal
Output
mA MAX
+5.0, ±12
+5.0, ±15
+3.3, ±12
+5.0, ±12
+5000, ±1000
+5000, ±800
+5000, ±1000
+5000, ±1000
SIDE VIEW
0.040 (1.02) DIA
6 PLACES
2.50
(63.5)
9
2.75
(70.0)
8
7
6
5
3.00
(76.2)
General Specifications (1)
pF
ON Logic Level or Pin Open
MIN
2.5
Volts
Off Logic Level or Tie to -Input
MAX
0.7
Volts
Converter Idle Current
TYP
10
mA
Remote ON/OFF
PIN CONNECTIONS
PIN NUMBER
PIN OUT
1
-INPUT
2
+INPUT
3
N/C
4
ON/OFF
5
TRIM
6
+3.3V OR +5V
7
COMMON
8
+12V OR +15V
9
-12V OR -15V
Output Trim Function
Input Resistance
TYP
40
kΩ
Programming Range
MIN
±10
%
Case Operating Range (2)
MIN
MAX
-25
+60
°C
Case Functional Range
MIN
MAX
-40
+105
°C
Storage Range
MIN
MAX
-45
+105
°C
Thermal Impedance
TYP
10
°C/Watt
MTBF (Calculated)
TYP
1,000,000
Hours
Unit Weight
TYP
2.6/71
oz/gm
Environmental
General
Rev. 04/2000
NOTE: All pins are 0.040"
diameter brass with tin plating.
Mechanical tolerances unless
otherwise noted:
X.XX dimensions: ±0.020 inches
X.XXX dimensions: ±0.005 inches
NOTES
(1) All parameters measured at 25°C, nominal input voltage,
and full rated load unless otherwise noted.
(2) Derate linearly to 0 Watts at 105°C ambient. Operation to
+70°C ambient with externally supplied forced air cooling,
100LFM.
(3) Case is tied to -Input, Pin 1.
1
0.43
(11.0)
700
0.000
TYP
Input to Output Capacitance
4
0.38
(9.65)
Volts
2
2.05
(52.1)
700
1544
1
1.65
(42.0)
MIN
MIN
0.45
(11.4)
Isolation Voltage
Input to Output
12V, 24V Input
48V Input
10µA Leakage
0.00
0.25
(6.3)
0.00
1.25
(31.8)
Units
0.85
(21.6)
All Models
Isolation (3)
DFC25 SERIES – TRIPLE OUTPUT
Input Parameters (1)
Model
DFC25E24T5/12
DFC25E24T5/15
DFC25E48T3.3/12
DFC25E48T5/12
Units
Reflected Ripple (2)
TYP
230
230
150
150
mAPP
Input Current
Full Load
No Load
TYP
TYP
1563
10
1563
10
890
10
781
10
mA
Inrush Current (5)
MAX
50
50
50
50
APK
Efficiency
TYP
80
80
78
80
%
Switching Frequency
TYP
150
150
150
150
kHz
Maximum Input
Overvoltage,
100ms Maximum
MAX
45
45
85
85
VDC
Turn-on Time,
1% Output Error
TYP
10
10
10
10
mS
Output Parameters (1)
Model
Output (8)
Output Voltage
DFC25EXXT3.3/XX
DFC25EXXT5/XX
DFC25EXXTX/12
DFC25EXXTX/15
V1
V1
V2,V3
V2,V3
Units
3.3
5
12
15
VDC
Output Voltage Accuracy
MIN
TYP
MAX
3.27
3.30
3.33
5.05
5.10
5.15
11.88
12.00
12.12
14.85
15.00
15.15
VDC
Rated Load Range
MIN
MAX
0.5
5.0
0.5
5.0
0.0
1.0
0.0
0.8
A
Load Regulation
25% Load - Max Load
TYP
1.0
1.0
8.0
8.0
%
Line Regulation
Vin = Min-Max VDC
TYP
0.2
0.2
3.0
3.0
%
Cross Regulation
25% Load - Max Load (6)
TYP
3.0
3.0
8.0
8.0
%
Transient Response
25% Load Step (7)
TYP
2
2
2
2
%
Short Term Stability (3)
TYP
<0.05
<0.05
<0.05
<0.05
%/24Hrs
Long Term Stability
TYP
<0.1
<0.1
<0.1
<0.1
%/kHrs
Input Ripple Rejection (4)
TYP
>40
>40
>40
>40
dB
Noise, Peak - Peak (2)
TYP
75
75
120
150
mVPP
Temperature Coefficient
TYP
100
100
300
300
ppm/°C
Short Circuit Protection
from +OUT to -OUT
Continuous Current Limit Protection on 3.3V or 5V outputs,
Momentary Current Limit Protection on 12V or 15V outputs
NOTES
(1) All All parameters measured at Tc=25°C, nominal input voltage and full rated load unless otherwise
noted.
(2) Measurement bandwidth is 0-20 MHz for peak-peak measurements, 10 kHz to 1 MHz for RMS
measurements. Output noise is measured with a 0.01µF/100V ceramic capacitor in parallel with a
1µF/35V Tantalum capacitor, 1 inch from the output pins to simulate standard PCB decoupling
capacitance.
(3) Short term stability is specified after a 30 minute warm-up at full load, constant line and recording
the drift over a 24 hour period.
(4) The transient response is specified as the time required to settle from a 50 to 75% step load change
(rise time of step = 2µSec) to a 1% error band.
(5) Per ETSI-300-132
(6) Change to main channel output for a 25% to 100% change on dual outputs or change on dual
channel outputs due to a 25% to 100% change on the main channel output.
(7) Recovery to within 1% in less than 1 millisecond after transient has been applied.
(8) V3 is defined as the minus, or negative output. Values in the chart are shown as positive for V2, and
can be assumed negative for V3.
DFC25 SERIES APPLICATION NOTES:
External Capacitance Requirements
A low ESR external capacitance is required for operation of the DFC25 Series. For maximum
performance, it is recommended that the DFC25 Series uses a capacitor of sufficient ripple current
capacity connected across the input pins, especially if a capacitive input source is farther than 1"
from the converter. To meet the reflected ripple requirements of the converter, an input impedance
of less than 0.09 Ohms at 200 kHz is required. External output capacitance is not required for
operation, however it is recommended that 1µF to 10µF of Tantalum and 0.001 to 0.1µF ceramic
capacitance be selected for each output to reduce system noise. Additional output capacitance may
be added for increased filtering, but should not exceed 400µF.
Remote ON/OFF Operation
The remote ON/OFF pin may be left floating if this function is not used. It is recommended to drive
this pin with TTL compatible circuitry. When the ON/OFF pin is pulled low with respect to the
-INPUT, the converter is placed in a low power drain state. The input capacitors are kept fully
charged in the OFF mode. For proper operation, this input may be driven from a logic gate directly.
The ON/OFF pin should never be pulled more than 0.3 volts below -INPUT or have a voltage
greater than +6 volts applied.
NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems, equipment used in hazardous environments,
or nuclear control systems without the express written consent of the President of Power-One, Inc.
TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are
subject to change without notice.
2
Similar pages