GSI GS70328TS-15 32k x 8 256kb asynchronous sram Datasheet

GS70328SJ/TS
32K x 8
256Kb Asynchronous SRAM
SOJ, TSOP
Commercial Temp
Industrial Temp
7, 8, 10, 12, 15 ns
3.3 V VDD
Corner VDD and VSS
Features
• Fast access time: 7, 8, 10, 12, 15 ns
• 75/65/50/50/50 mA at max cycle rate
• Single 3.3 V ± 0.3 V power supply
• All inputs and outputs are TTL-compatible
• Fully static operation
• Industrial Temperature Option: –40° to 85°C
• Package line up
SJ: 300 mil, 28-pin SOJ package
TS: 8 mm x 13.4 mm, 28-pin TSOP Type I package
Pin Descriptions
Symbol
Description
A0–A14
Address input
DQ1–DQ8
Data input/output
CE
Chip enable input
WE
Write enable input
OE
Output enable input
VDD
+3.3 V power supply
VSS
Ground
NC
No connect
Description
The GS70328 is a high speed CMOS static RAM organized as
32,763 words by 8 bits. Static design eliminates the need for
external clocks or timing strobes. The GS70328 operates on a
single 3.3 V power supply, and all inputs and outputs are TTLcompatible. The GS70328 is available in 300 mil, 28-pin SOJ
and 8 x 13.4 mm2, 28-pin TSOP Type-I packages.
Pin Configuration
Top view
A14
1
28
A12
2
27
WE
A7
3
26
A13
A6
4
25
A8
A5
5
24
A9
A4
6
23
A11
A3
7
22
OE
21
A10
20
CE
28-pin
300 mil
VDD
A2
8
A1
9
A0
10
19
DQ8
DQ1
11
18
DQ7
DQ2
12
17
DQ6
DQ3
13
16
DQ5
VSS
14
15
DQ4
Rev: 1.11 11/2004
SOJ
OE
A11
A9
A8
A13
WE
VDD
A14
A12
A7
A6
A5
A4
A3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28- pin
8 x 13.4 TSOP I
1/11
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
28
27
26
25
24
23
22
21
20
19
18
17
16
15
A10
CE
DQ8
DQ7
DQ6
DQ5
DQ4
VSS
DQ3
DQ2
DQ1
A0
A1
A2
© 1999, GSI Technology
GS70328SJ/TS
Block Diagram
A0
Address
Input
Buffer
Row
Decoder
Memory Array
Column
Decoder
A14
CE
WE
OE
I/O Buffer
Control
DQ1
DQ8
Truth Table
CE
OE
WE
DQ1 to DQ8
VDD Current
H
X
X
Not Selected
ISB1, ISB2
L
L
H
Read
L
X
L
Write
L
H
H
High Z
IDD
X: “H” or “L”
Absolute Maximum Ratings
Parameter
Symbol
Rating
Unit
Supply Voltage
VDD
–0.5 to +4.6
V
Input Voltage
VIN
–0.5 to VDD + 0.5
(≤ 4.6 V max.)
V
Output Voltage
VOUT
–0.5 to VDD + 0.5
(≤ 4.6 V max.)
V
Allowable power dissipation
PD
0.7
W
Storage temperature
TSTG
–55 to 150
o
C
Note:
Permanent device damage may occur if Absolute Maximum Ratings are exceeded. Functional operation shall be restricted to Recommended
Operating Conditions. Exposure to higher than recommended voltages for extended periods of time could affect device reliability.
Rev: 1.11 11/2004
2/11
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 1999, GSI Technology
GS70328SJ/TS
Recommended Operating Conditions
Parameter
Symbol
Minimum
Typical
Maximum
Unit
Supply Voltage for -7/8/10/12
VDD
3.0
3.3
3.6
V
Input High Voltage
VIH
2.0
—
VDD + 0.3
V
Input Low Voltage
VIL
–0.3
—
0.8
V
Ambient Temperature,
Commercial Range
TAc
0
—
70
oC
Ambient Temperature,
Industrial Range
TAI
–40
—
85
o
C
Notes:
1. Input overshoot voltage should be less than VDD +2 V and not exceed 20 ns.
2. Input undershoot voltage should be greater than –2 V and not exceed 20 ns.
Capacitance
Parameter
Symbol
Test Condition
Maximum
Unit
Input Capacitance
CIN
VIN = 0 V
5
pF
Output Capacitance
COUT
VOUT = 0 V
7
pF
Notes:
1. Tested at TA = 25°C, f = 1 MHz
2. These parameters are sampled and are not 100% tested.
DC I/O Pin Characteristics
Parameter
Symbol
Test Conditions
Min
Max
Input Leakage Current
IIL
VIN = 0 to VDD
–1uA
1uA
Output Leakage Current
ILO
Output High Z
VOUT = 0 to VDD
–1uA
1uA
Output High Voltage
VOH
IOH = –4 mA
2.4 V
—
Output Low Voltage
VOL
ILO = +4 mA
—
0.4 V
Rev: 1.11 11/2004
3/11
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 1999, GSI Technology
GS70328SJ/TS
Power Supply Currents
Parameter Symbol
Operating
Supply
Current
Standby
Current
Standby
Current
Test Conditions
0 to 70°C
7 ns
8 ns
10 ns 12 ns 15 ns
-40 to 85°C
7 ns
8 ns
10 ns 12 ns 15 ns
IDD
CE ≤ VIL
All other inputs
≥ VIH or ≤ VIL
Min. cycle time
IOUT = 0 mA
75 mA 65 mA 50 mA 50 mA 50 mA 80 mA 70 mA 55 mA 55 mA 55 mA
ISB1
CE ≥ VIH
All other inputs
≥ VIH or ≤VIL
Min. cycle time
35 mA 30 mA 25 mA 25 mA 25 mA 40 mA 35 mA 30 mA 30 mA 30 mA
ISB2
CE ≥ VDD – 0.2 V
All other inputs
≥ VDD – 0.2 V or
≤ 0.2 V
1 mA
2 mA
AC Test Conditions
Output Load 1
Parameter
Conditions
Input high level
VIH = 2.4 V
Input low level
VIL = 0.4 V
50Ω
Input rise time
tr = 1 V/ns
VT = 1.4 V
Input fall time
tf = 1 V/ns
Input reference level
1.4 V
Output Load 2
Output reference level
1.4 V
3.3 V
Output load
Fig. 1& 2
DQ
Rev: 1.11 11/2004
589Ω
DQ
Notes:
1. Include scope and jig capacitance
2. Test conditions as specified with output loading as shown in Fig. 1
unless otherwise noted
3. Output load 2 for tLZ, tHZ, tOLZ and tOHZ
4/11
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
30pF1
5pF1
434Ω
© 1999, GSI Technology
GS70328SJ/TS
AC Characteristics
Read Cycle
Parameter
Symbol
Read cycle time
-7
-8
-10
-12
-15
Unit
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
tRC
7
—
8
—
10
—
12
—
15
—
ns
Address access time
tAA
—
7
—
8
—
10
—
12
—
15
ns
Chip enable access time (CE)
tAC
—
7
—
8
—
10
—
12
—
15
ns
Output enable to output valid (OE)
tOE
—
3.5
—
4
—
5
—
6
—
7
ns
Output hold from address change
tOH
2
—
2
—
2
—
3
—
3
—
ns
Chip enable to output in low Z (CE)
tLZ*
2
—
2
—
2
—
3
—
3
—
ns
Output enable to output in low Z (OE)
tOLZ*
0
—
0
—
0
—
0
—
0
—
ns
Chip disable to output in High Z (CE)
tHZ*
—
3.5
—
4
—
5
—
6
—
7
ns
Output disable to output in High Z (OE)
tOHZ*
—
3
—
3.5
—
4
—
5
—
6
ns
* These parameters are sampled and are not 100% tested
Read Cycle 1: CE = OE = VIL, WE = VIH
tRC
Address
tAA
tOH
Data Out
Rev: 1.11 11/2004
Previous Data
Data valid
5/11
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 1999, GSI Technology
GS70328SJ/TS
Read Cycle 2: WE = VIH
tRC
Address
tAA
CE
tAC
tHZ
tLZ
OE
tOE
tOHZ
tOLZ
Data Out
DATA VALID
High impedance
Write Cycle
Parameter
Symbol
Write cycle time
-7
-8
-10
-12
-15
Unit
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
tWC
7
—
8
—
10
—
12
—
15
—
ns
Address valid to end of write
tAW
5
—
5.5
—
7
—
10
—
13
—
ns
Chip enable to end of write
tCW
5
—
5.5
—
7
—
10
—
13
—
ns
Data set up time
tDW
3.5
—
4
—
5
—
7
—
10
—
ns
Data hold time
tDH
0
—
0
—
0
—
0
—
0
—
ns
Write pulse width
tWP
5
—
5.5
—
7
—
10
—
13
—
ns
Address set up time
tAS
0
—
0
—
0
—
0
—
0
—
ns
Write recovery time (WE)
tWR
0
—
0
—
0
—
0
—
0
—
ns
Write recovery time (CE)
tWR1
0
—
0
—
0
—
0
—
0
—
ns
Output Low Z from end of write
tWLZ*
2
—
2
—
2
—
3
—
3
—
ns
Write to output in High Z
tWHZ*
—
3
—
3.5
—
4
—
5
—
5
ns
* These parameters are sampled and are not 100% tested
Rev: 1.11 11/2004
6/11
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 1999, GSI Technology
GS70328SJ/TS
Write Cycle 1: WE control
tWC
Address
tAW
tWR
OE
tCW
CE
tAS
tWP
WE
tDW
Data In
tDH
DATA VALID
tWHZ
tWLZ
Data Out
HIGH IMPEDANCE
Write Cycle 2: CE control
tWC
Address
tAW
tWR1
OE
tAS
tCW
CE
tBW
UB, LB
tWP
WE
tDW
Data In
DATA VALID
Data Out
Rev: 1.11 11/2004
tDH
HIGH IMPEDANCE
7/11
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 1999, GSI Technology
GS70328SJ/TS
28-Pin SOJ, 300 mil
Dimension in inch
L
D
e
A
A1
A
A2
1
GE
E
HE
c
y
B
B1
Detail A
Θ
Dimension in mm
Symbol
min
nom
max
min
nom
max
A
—
—
0.148
—
—
3.76
A1
0.025
—
—
0.64
—
—
A2
0.095
0.100
0.105
2.41
2.54
2.67
B
0.015
—
0.020
0.38
—
0.51
B1
0.026
0.028
0.032
0.66
0.71
0.81
c
D
0.008
0.705
0.010
0.71
0.012
0.715
0.20
17.91
0.25
18.03
0.30
18.16
E
0.295
0.300
0.305
7.49
7.62
7.75
e
—
0.05
—
—
1.27
—
HE
0.330
0.335
0.340
8.38
8.51
8.64
GE
0.255
0.265
0.275
6.48
6.73
6.985
L
0.082
—
—
2.08
—
—
y
—
—
0.004
—
—
0.10
Θ
o
o
—
10o
0
—
10
o
0
Notes:
1. Dimension D& E do not include interlead flash
2. Dimension B1 does not include dambar protrusion/intrusion
3. Controlling dimension: inches
Rev: 1.11 11/2004
8/11
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 1999, GSI Technology
GS70328SJ/TS
28-Pin TSOP-I, 8 mm x 13.4 mm
Dimension in inch
E
28
c
L
1
e
GE
E
HE
c
HD
D
D
A
A
A2
A
e
yB
B
B1
L1
Detail A
A1
L
A
A2
A1
1
y
Detail A
Rev: 1.11 11/2004
Θ
Q
Dimension in mm
Symbol
min
nom
max
min
nom
max
A
—
—
0.047
—
—
1.20
A1
0.002
—
0.006
0.05
—
0.15
A2
0.035
0.040
0.041
0.90
1.00
1.05
B
0.007
0.008
0.011
0.17
0.20
0.27
D
—
0.465
—
—
11.8
—
HD
—
.528
—
—
13.4
—
c
0.004
0.006
0.008
0.10
0.15
0.21
E
—
0.315
—
—
8.00
—
e
—
0.022
—
—
0.55
—
L
0.020
0.024
0.028
0.50
0.60
0.70
L1
0.024
0.032
0.040
0.60
0.80
1.00
y
—
—
0.003
—
—
0.08
Θ
0o
—
5o
0o
—
5o
Notes:
1. Dimension D& E do not include interlead flash
2. Dimension B1 does not include dambar protrusion/intrusion
3. Controlling dimension: inches
4. Profile tolerance zones for D and E do not include mold
protrusion. Allowable mold protrusion on E is 0.15 mm per side
and on D is 0.25 mm per side.
9/11
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 1999, GSI Technology
GS70328SJ/TS
Ordering Information
*
Part Number*
Package
Access Time
Temp. Range
GS70328SJ-7
300-mil SOJ
7 ns
Commercial
GS70328SJ-8
300-mil SOJ
8 ns
Commercial
GS70328SJ-10
300-mil SOJ
10 ns
Commercial
GS70328SJ-12
300-mil SOJ
12 ns
Commercial
GS70328SJ-15
300-mil SOJ
15 ns
Commercial
GS70328SJ-7I
300-mil SOJ
7 ns
Industrial
GS70328SJ-8I
300-mil SOJ
8 ns
Industrial
GS70328SJ-10I
300-mil SOJ
10 ns
Industrial
GS70328SJ-12I
300-mil SOJ
12 ns
Industrial
GS70328SJ-15I
300-mil SOJ
15 ns
Industrial
GS70328TS-7
TSOP-I 8 x 13.4 mm2
7 ns
Commercial
GS70328TS-8
TSOP-I 8 x 13.4 mm2
8 ns
Commercial
GS70328TS-10
TSOP-I 8 x 13.4 mm2
10 ns
Commercial
GS70328TS-12
TSOP-I 8 x 13.4 mm2
12 ns
Commercial
GS70328TS-15
TSOP-I 8 x 13.4 mm2
15 ns
Commercial
GS70328TS-7I
TSOP-I 8 x 13.4 mm2
7 ns
Industrial
GS70328TS-8I
TSOP-I 8 x 13.4 mm2
8 ns
Industrial
GS70328TS-10I
TSOP-I 8 x 13.4 mm2
10 ns
Industrial
GS70328TS-12I
TSOP-I 8 x 13.4 mm2
12 ns
Industrial
GS70328TS-15I
TSOP-I 8 x 13.4 mm2
15 ns
Industrial
Status
Customers requiring delivery in Tape and Reel should add the character “T” to the end of the part number. For example: GS70328TP-8T
Rev: 1.11 11/2004
10/11
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 1999, GSI Technology
GS70328SJ/TS
R
evision History
Rev. Code: Old;
New
Types of Changes
Format or Content
1.03 8/1999;
1.04 11/1999
Content
GS70328Rev1.04 12/1999KRev
1.05 2/2000L
Rev 1.05 2/2000L; Rev1.06 6/2000
Rev1.06; Rev1.07
Format/Content
Content
Format/Content
Page #/Revisions/Reason
• Added 12ns speed bin information to 70328 datasheet.
• GSI Logo
• Nominal value for HD on the TSOP-I 28-pin package changed
to 13.4
• Updated format to conform to Tech Pubs standards
• Corrected errors in both case diagrams
70328_r1_07; 70328_r1_08
Content
• Added 12 ns reference to Parameter column in
Recommended Operating Conditions table on page 3
70328_r1_08; 70328_r1_09
Content
• Added 15 ns references to entire document
70328_r1_09; 70328_r1_10
Content
• Removed 6 ns speed bin from entire document
70328_r1_10; 70328_r1_11
Format
• Updated format
Rev: 1.11 11/2004
11/11
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 1999, GSI Technology
Similar pages