Order this document by MC33197/D The MC33197 is a standard wiper timer control device designed for harsh automotive applications. The device can perform the intermittent, after wash, and continuous wiper timer functions. It is designed to directly drive a wiper motor relay. The MC33197 requires very few external components for full system implementation. The intermittent control pin can be switched to ground or Vbat to meet a large variety of possible applications. The intermittent timing can be fixed or adjustable via an external resistor. The MC33197 is built using bipolar technology and parametrically specified over the automotive ambient temperature range and 8.0 to 16 V supply voltage. The MC33197 can operate in both front and rear wiper applications. • • • • • • • • AUTOMOTIVE WASH WIPER TIMER SEMICONDUCTOR TECHNICAL DATA Adjustable Time Interval of Less Than 500 ms to More Than 30 s 8 Intermittent Control Pin Can Be Switched to Ground or Vbat 1 Adjustable After Wipe Time P SUFFIX PLASTIC PACKAGE CASE 626 Priority to Continuous Wipe Minimum Number of Timing Components Integrated Relay Driver With Free Wheeling Protection Diode Operating Voltage Range From 8.0 to 16 V 8 For Front Wiper and Rear Wiper Window Applications 1 D SUFFIX PLASTIC PACKAGE CASE 751 (SO–8) ORDERING INFORMATION Device Operating Temperature Range MC33197D TA = – 40° to +105°C SO–8 MC33197P TA = – 40° to +125°C DIP–8 Package PIN CONNECTIONS MAXIMUM RATINGS Rating Symbol Value Unit Continuous Supply Voltage (VPin 6) VCC 16 V Storage Temperature Tstg –55 to +150 °C Thermal Resistance (Junction–to–Ambient) DIP–8 Package SO–8 Package RθJA °C TA Operating Junction Temperature Range TJ –40 to +150 °C TJ(max) 150 °C –40 to +125 –40 to +105 This document contains information on a new product. Specifications and information herein are subject to change without notice. MOTOROLA ANALOG IC DEVICE DATA 1 8 Out 2 Osc1 3 7 Gnd 6 VCC CONT 4 5 W/W (Top View) °C/W 100 145 Operating Ambient Temperature Range DIP–8 Package SO–8 Package Maximum Junction Temperature INT Osc2 (SO–8) Osc1 1 8 Osc2 CONT 2 W/W 3 7 INT 6 Out VCC 4 5 Gnd (Top View) Motorola, Inc. 1996 1 MC33197 Representative Block Diagram Vbb Vbb VCC Variable Current Sources R1 = 220 Ω R2 = 22 kΩ R3 = 1.5 to 22 kΩ R4 = 4.7 kΩ R5 = 4.7 kΩ C1 = 47 µF C2 = 100 nF R1 C1 Wiper Motor Relay MC33197 Out Int Switch INT R3 Ref Osc2 Gnd Input Comparator Logic Water Pump Motor W/W Ref R4 Vbb C2 M Ref Osc1 R2 Gnd Input Comparator with Hysteresis CONT R5 Cont Switch This device contains 390 active transistors. ELECTRICAL CHARACTERISTICS (–40°C ≤ TA ≤ +125°C, 8.0 V ≤ VCC ≤ 16 V, unless otherwise noted. Typical values reflect approximate mean at TA = 25°C with VCC = 14 V at the time of initial device characterization.) Characteristic Symbol Min Typ Max Unit Functional Supply Voltage Range VCCF 8.0 – 18 V Operating Supply Voltage Range VCCOP 8.0 – 16 V Standby Supply Current (VCC = 16 V, R2 = 68 k) ICC – 4.0 5.2 mA Supply Current INT Active (R3 = 2.5 k) ICC – 7.0 8.4 mA Supply Current Relay “On” (R2 = 68 k) ICC – 7.5 11.2 mA Supply Current INT and Relay “On” (R2 = 68 k, R3 = 2.5 k) ICC – 10 14.5 mA Oscillator Variations with Supply Voltage and Temperature (excluding external component tolerances, C2 = 100 nF polyester capacitor) (Notes 1 & 2) 10 V ≤ Vbb ≤ 16 V 8.0 V ≤ Vbb ≤ 16 V Kosc % – – 10 15 – – RL 60 – – Ω Output Voltage (Iout = 200 mA) Vout – 0.9 1.5 V Output Clamp Voltage (Iout = 20 mA) Vcl 19.5 – 22 V Oscillator Period Coefficient (TA = 25°C) Vbb = 13 V (Note 3) Vbb = 13 V (INT Connected to Gnd) (Note 4) Vbb = 13 V (INT Connected to Vbat, R1 = 220 Ω) (Note 4) tb1 tb2g tb2v 0.98 15.1 11.5 1.0 15.5 12.1 1.03 15.9 12.7 CONT Threshold (VCC = 13 V) Vih 6.0 – 8.5 V CONT Threshold (VCC = 16 V) Vih – VCC/2 – V Relay Resistance – NOTES: 1. The oscillator frequency is defined by the current flowing through the external resistor R2. The voltage at the INT pin is (VCC/2 – Vbe) and hence the current flowing through R3 is different if R3 is connected to Vbb or to Gnd because of the voltage drop across resistor R1. This voltage drop causes the oscillator coefficient for tb2 to be different for the two cases of INT terminated to Gnd or to Vbb. Because of this, the oscillator coefficient is speci– fied with a specific value of R1 whenever INT is connected to Vbb. If R1 is changed, the coefficient will change. Also, any extra current through the resistor R1 other than the current used by the device will cause timing deviations in tb2 timings (as in the case where two devices are sharing a common R1 resistor). 2. The oscillator stability with temperature is dependent on the temperature coefficients of the external components. If the capacitance value of the external capacitor varies more than 5% over the parametric temperature range, the figures quoted for oscillator variation are not valid. 3. The tb1 duration is given by coefficient 4 x R2 x C2 (tb1 duration = tb1 x 4 x R2 x C2). 4. The tb2 duration is given by coefficient x R3 x C2 (tb2 duration = tb2 x R3 x C2). 2 MOTOROLA ANALOG IC DEVICE DATA MC33197 Figure 1. Intermittent Wash Wiper Typical Application + Battery Line Vbb C1 R1 Washer VCC R3 Intermittent Low Speed High Speed INT MC33197 R4 W/W Osc2 Out Wiper Motor Osc1 Gnd Low Speed M C2 Wash Wipe Switch R2 Water Pump M High Speed This application shows the MC33197 with the external wirings and two speed wiper motor. This application has the Intermittent and Wash Wiper functions. INTRODUCTION The MC33197 is a wiper timer control device designed for use in harsh automotive applications. The device can perform the intermittent, after wash, and continuous wiper timer functions. The MC33197 is designed to directly drive a wiper motor relay. The MC33197 is suitable for both front and rear wiper applications. The MC33197 connects directly to the vehicle’s battery voltage (Vbat) through a 220 Ω resistor used with a 47 µF de–coupling filter capacitor. The device has an internal oscillator controlled by one of two external resistors (R2 and R3) in addition to one external capacitor (C2), dependent on the application function required. The values of C2 and R2 determine the tb1 time base. Tb1 is used to generate the relay wiper activation during the INT function (T3) and the after wash timing (T2) during the wash wipe mode. The values C2 and R3 determine the tb2 time base. The tb2 time base is used to generate the pause or intermittent time (T4). The intermittent wiper function can generate intermittent timing (T4) from less than 500 ms to more than 30 seconds. The intermittent function of the device can be activated by the INT input connected to either ground or Vbat. The intermittent timing is externally adjustable by changing the value of resistor R3. The wash wiper timer function detects the water pump MOTOROLA ANALOG IC DEVICE DATA motor’s operation. When the pump motor activation is detected, the MC33197 turns the wiper on for the entire duration of the pump motor’s activation. When the motor is turned off, it generates an after wash timing (T2) to maintain the wiping action. The W/W pin is connected to the water pump motor through a protection resistor (R4). The MC33197 also has a continuous function, which activates the wiper relay whenever the CONT input is activated. The CONT input is connected to a switch through a protection resistor (R5). The CONT input comparator has an input threshold of Vbb/2 with hysteresis. The device has internal debounce circuitry, based on the oscillator period. This provides filtering of the intermittent (INT) and wash wipe (W/W) input signals (see T1 Debounce Timing paragraph that follows). The device directly drives the wiper motor relay. It internally incorporates a 20 V free wheeling zener diode to protect the device against overvoltage spikes produced when relay is switched off. Intermittent Operation Conditions: • W/W not connected or connected to ground. • CONT not connected or connected to ground. • INT connected to Vbb or to ground. 3 MC33197 In this configuration, the circuit will respond to the switching of INT to either Vbb or ground after a time T1 (see T1 Debounce Timing). If INT is disconnected before the end of T1; no action will be taken. After a time T1, the output will be switched on for a duration, T3 = 16 x 4 x tb1 and then switched off for a duration, T4 = 144 x 4 x tb2. This sequence will continue to repeat so long as INT is disconnected from Vbb or ground for a time duration greater than T1. If INT is disconnected during the time T3; the output will remain on for the remainder of T3. This is illustrated in the diagram on Figure 2. Figure 2. Switching Waveform INT Timing other timing. Therefore, the circuit will not be reset to a defined state. Wash Wiper and Intermittent Operation If W/W is activated during the time INT is also activated, the circuit will respond to W/W after a time T1 (see T1 Debounce Timing). The output will turn on after T1, and stay on for a time T2 + T3 after W/W is deactivated. Following this, normal operation of INT will occur. This is shown on Figure 4. Figure 4. Switching Waveform W/W and INT Active INT W/W INT Out Out T1 T1 T4 T3 T3 T4 Wash Wipe Operation Conditions: • INT disconnected. • CONT disconnected or connected to ground. In this condition, the circuit will respond to the switching of W/W to Vbb after a time T1 (see T1 Debounce Timing). If W/W is disconnected or connected to ground before the end of T1; no action will be taken. After a time T1; the circuit will perform as shown on Figure 3. The output will turn on and remain on for the duration of W/W. When W/W becomes inactive, the output will remain on for T2 = 96 x 4 x tb1. T1 Debounce Timing The criteria for an input signal to be detected is that it should be active at two successive negative internal clock edges. The inputs are sampled on the negative edge of the internal clock. If two consecutive samples are the same, the input is detected as being in that state. Hence the time T1 from a signal becoming active to the time that the circuit responds can be anytime from 4 x tb1 to 2 x 4 x tb1 (due to synchronizing the input to the oscillator period) when the oscillator is oscillating with a time base of tb1 and 4 x tb2 to 2 x 4 x tb2, when the oscillator is oscillating with a time base of tb2. The following table summarizes all T1 debounce timings: Condition Figure 3. Switching Waveform W/W Timing W/W Out T1 Debounce Time INT Active 4 x tb1 to 2 x 4 x tb1 INT Inactive 4 x tb1 to 2 x 4 x tb1 W/W Active When INT Inactive 4 x tb1 to 2 x 4 x tb1 W/W Active When INT Active During T3 4 x tb1 to 2 x 4 x tb1 W/W Active When INT Active During T4 4 x tb2 to 2 x 4 x tb2 T2 Continuous Operation In this condition, the circuit responds to the switching of CONT to Vbb. If CONT is connected to Vbb, the output will turn on regardless of the state of any other input and remain on so long as CONT is active. This command operates directly on the relay output and does not interfere with any 4 T3 T2 Two MC33197 Devices Using One Decoupling Resistor and Capacitor Two devices may be connected to the power source using a common R1 resistor for protection against overvoltages. If this is done it should be noted that the current flowing through R1 is increased and hence the voltage drop across R1 is increased. MOTOROLA ANALOG IC DEVICE DATA MC33197 Overvoltage Protection In reference to the Block Diagram and Typical Application, all of the foregoing operational cases require: R1 ≥ 100 Ω, C1 ≥ 47 µF R3 ≥ 1.0 kΩ, R4 ≥ 4.7 kΩ, R5 ≥ 4.7 kΩ The circuit will not operate during the transient conditions. By using the above component values, the circuit will be able to sustain the following overvoltages on Vbb without permanent damage: 1. +28 V for 5 minutes 2. –15 V for 5 minutes 3. –16 V cycled off for 1.0 minute 4. +80 V pulse decaying exponentially to 8.0 V in 400 ms repeated 3 times at 1.0 minute intervals. 5. ± 300 V pulse decaying exponentially to 30 V in 300 ms with a maximum energy of 1.0 Joule. 6. ±100 V pulse decaying exponentially to 10 V in 2 ms. Recommended External Component Values Below are the recommended component values to ensure the device will operate properly, and that all specified parameters will stay within their tolerances. R1 should be greater than 100 Ω; recommended value of 220 Ω. R1 can be up to 500 Ω, but in this case the tb2v parameter could be out of it’s specified value (see Electrical Characteristics and Note 1). Also, the minimum operating voltage range should be greater than 8.0 V. The following values should be adhered to: 10 kΩ ≤ R2 ≤ 68 kΩ 1.5 kΩ ≤ R3 ≤ 47 kΩ R4 ≥ 4.7 kΩ R5 ≥ 4.7 kΩ C1 ≥ 47 uF 47 nF ≤ C2 ≤ 470 nF MOTOROLA ANALOG IC DEVICE DATA Application Information The following is an example of timing calculations using the following external components values: R2 = 22 kΩ, R3 = 2.2 kΩ, C2 = 100 nF (Referring to Block Diagram and Typical Application). Oscillator Time Base Calculation: tb1 duration = tb1 x 4 x R2 x C2 = 1 x 4 x 27e3 x 100e–9 = 10.8 ms tb2 duration_g (INT to Gnd) = tb2g x R3 x C2 = 15.5 x 2.2e3 x 100e–9 = 3.41 ms tb2 duration_v (INT to Vbb) = tb2v x R3 x C2 = 12.1 x 2.2e3 x 100e–9 = 2.66 ms Intermittent timing calculation: T3 = 16 x 4 x tb1 duration = 16 x 4 x 10.8 ms = 691 ms T4 = 144 x 4 x tb2 duration_g = 144 x 4 x 3.41 ms = 1.96 s (INT connected to Gnd) T4 = 144 x 4 x tb2 duration_v = 144 x 4 x 2.66 ms = 1.53 s (INT connected to Vbb) Wash wipe timing calculation: T2 = 96 x 4 x tb1 = 96 x 4 x 10.8 ms = 4.15 s T1 Debounce Time Calculation (see T1 Debounce Timing) When oscillator is oscillating at tb1: T1 minimum = 4 x tb1 = 4 x 10.8 ms = 43.2 ms T1 maximum = 2 x 4 x tb1 = 2 x 4 x 10.8 ms = 86.4 ms When oscillator is oscillating at tb2: T1 minimum (INT connected to Gnd, tb2g) = 4 x tb2 = 4 x 3.41 ms = 13.6 ms T1 maximum (INT connected to Gnd, tb2g) = 2 x 4 x tb2 = 2 x 4 x 3.41 ms = 27.3 ms 5 MC33197 OUTLINE DIMENSIONS P SUFFIX PLASTIC PACKAGE CASE 626–05 ISSUE K 8 NOTES: 1. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 2. PACKAGE CONTOUR OPTIONAL (ROUND OR SQUARE CORNERS). 3. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5 –B– 1 4 DIM A B C D F G H J K L M N F –A– NOTE 2 L C J –T– N SEATING PLANE D STYLE 1: PIN 1. 2. 3. 4. 5. 6. 7. 8. M K G H 0.13 (0.005) M T A B M MILLIMETERS MIN MAX 9.40 10.16 6.10 6.60 3.94 4.45 0.38 0.51 1.02 1.78 2.54 BSC 0.76 1.27 0.20 0.30 2.92 3.43 7.62 BSC ––– 10_ 0.76 1.01 M INCHES MIN MAX 0.370 0.400 0.240 0.260 0.155 0.175 0.015 0.020 0.040 0.070 0.100 BSC 0.030 0.050 0.008 0.012 0.115 0.135 0.300 BSC ––– 10_ 0.030 0.040 AC IN DC + IN DC – IN AC IN GROUND OUTPUT AUXILIARY VCC D SUFFIX PLASTIC PACKAGE CASE 751–05 (SO–8) ISSUE N NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. –A– 8 5 –B– 1 4X P 0.25 (0.010) 4 M B M G R C –T– 8X D 0.25 (0.010) 6 K M T B SEATING PLANE S A M_ S X 45 _ F J DIM A B C D F G J K M P R MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.18 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.189 0.196 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.007 0.009 0.004 0.009 0_ 7_ 0.229 0.244 0.010 0.019 MOTOROLA ANALOG IC DEVICE DATA MC33197 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. MOTOROLA ANALOG IC DEVICE DATA 7 MC33197 How to reach us: USA / EUROPE: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315 MFAX: [email protected] – TOUCHTONE (602) 244–6609 INTERNET: http://Design–NET.com HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 8 ◊ *MC33197/D* MC33197/D MOTOROLA ANALOG IC DEVICE DATA